diff options
Diffstat (limited to 'firmware/configuration/t841_default/Makefile.inc')
| -rw-r--r-- | firmware/configuration/t841_default/Makefile.inc | 60 |
1 files changed, 60 insertions, 0 deletions
diff --git a/firmware/configuration/t841_default/Makefile.inc b/firmware/configuration/t841_default/Makefile.inc new file mode 100644 index 0000000..9601a69 --- /dev/null +++ b/firmware/configuration/t841_default/Makefile.inc @@ -0,0 +1,60 @@ +# Name: Makefile +# Project: Micronucleus +# License: GNU GPL v2 (see License.txt) +# +# Controller type: ATtiny 841 +# Configuration: Default configuration - 12 Mhz RC oscillator +# Last Change: Mar 16,2014 + + +F_CPU = 12000000 +DEVICE = attiny841 + +# hexadecimal address for bootloader section to begin. To calculate the best value: +# - make clean; make main.hex; ### output will list data: 2124 (or something like that) +# - for the size of your device (8kb = 1024 * 8 = 8192) subtract above value 2124... = 6068 +# - How many pages in is that? 6068 / 64 (tiny85 page size in bytes) = 94.8125 +# - round that down to 94 - our new bootloader address is 94 * 64 = 6016, in hex = 1780 +BOOTLOADER_ADDRESS = 19C0 + +FUSEOPT = -U lfuse:w:0xe2:m -U hfuse:w:0xdd:m -U efuse:w:0xfe:m +FUSEOPT_DISABLERESET = # TODO + +#--------------------------------------------------------------------- +# ATtiny841 +#--------------------------------------------------------------------- +# Fuse extended byte: +# 0xFE = 1 1 1 1 1 1 1 0 +# ^ +# | +# +---- SELFPRGEN (enable self programming flash) +# +# Fuse high byte: +# 0xdd = 1 1 0 1 1 1 0 1 +# ^ ^ ^ ^ ^ \-+-/ +# | | | | | +------ BODLEVEL 2..0 (brownout trigger level -> 2.7V) +# | | | | +---------- EESAVE (preserve EEPROM on Chip Erase -> not preserved) +# | | | +-------------- WDTON (watchdog timer always on -> disable) +# | | +---------------- SPIEN (enable serial programming -> enabled) +# | +------------------ DWEN (debug wire enable) +# +-------------------- RSTDISBL (disable external reset -> enabled) +# +# Fuse high byte ("no reset": external reset disabled, can't program through SPI anymore) +# 0x5d = 0 1 0 1 1 1 0 1 +# ^ ^ ^ ^ ^ \-+-/ +# | | | | | +------ BODLEVEL 2..0 (brownout trigger level -> 2.7V) +# | | | | +---------- EESAVE (preserve EEPROM on Chip Erase -> not preserved) +# | | | +-------------- WDTON (watchdog timer always on -> disable) +# | | +---------------- SPIEN (enable serial programming -> enabled) +# | +------------------ DWEN (debug wire enable) +# +-------------------- RSTDISBL (disable external reset -> disabled!) +# +# Fuse low byte: +# 0xe2 = 1 1 1 0 0 0 1 0 +# ^ ^ \+/ \--+--/ +# | | | +------- CKSEL 3..0 (clock selection -> RC Oscillator) +# | | +--------------- SUT 1..0 (BOD enabled, fast rising power) +# | +------------------ CKOUT (clock output on CKOUT pin -> disabled) +# +-------------------- CKDIV8 (divide clock by 8 -> don't divide) + + |