1 files changed, 68 insertions, 0 deletions
diff --git a/boards/EA_LPCXPRESSO_LPC1769/board.c b/boards/EA_LPCXPRESSO_LPC1769/board.c
new file mode 100644
index 000000000..216b9e813
--- /dev/null
+++ b/boards/EA_LPCXPRESSO_LPC1769/board.c
@@ -0,0 +1,68 @@
+/*
+    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#include "ch.h"
+#include "hal.h"
+
+/**
+ * @brief   PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ *          This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config = {
+ {VAL_GPIO0DATA, VAL_GPIO0DIR},
+ {VAL_GPIO1DATA, VAL_GPIO1DIR},
+ {VAL_GPIO2DATA, VAL_GPIO2DIR},
+ {VAL_GPIO3DATA, VAL_GPIO3DIR},
+ {VAL_GPIO4DATA, VAL_GPIO4DIR}
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+
+  LPC17xx_clock_init();
+}
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+
+  /*
+   * Extra, board-specific, initializations.
+   */
+  LPC_PINCON->PINSEL0  |= (1UL << 4) | (1UL << 6); 	    /* Set UART0 TXD0 P0.2 and RXD0 P0.3 pins.*/
+  LPC_PINCON->PINMODE0 |= (2UL << 4) | (2UL << 6); 	    /* Disable pull-up on UART0 TXD0 and RXD0 pins.*/
+
+  LPC_PINCON->PINSEL3  |= (1UL << 22); 	                /* Set CLKOUT P1.27 pin.*/
+  LPC_PINCON->PINMODE3 |= (2UL << 22); 	                /* Disable pull-up on CLKOUT pin. */
+
+  /* I2C1 config */
+  LPC_PINCON->PINSEL1 |= (3UL << 8) | (3UL << 6);       /* Set I2C1 SCL1 P0.20, SDA1 P0.19 pins. */
+  LPC_PINCON->PINMODE1 |= (2UL << 8) | (2UL << 6);      /* Disable pull-up on I2C1 SCL1 P0.20, SDA1 P0.19 pins. */
+  LPC_PINCON->PINMODE_OD0 |= (1UL << 20) | (1UL << 19); /* Set I2C1 SCL1 P0.20, SDA1 P0.19 as open drain pins. */
+
+  /* ADC config */
+  LPC_PINCON->PINMODE1 |= (2UL << 16) | (2UL << 14);    /* Disable pull-up on AD0.1 P0.24 and AD0.0 P0.23 pins.*/
+  LPC_PINCON->PINSEL1 |= (1UL << 16) | (1UL << 14);     /* Set AD0.1 P0.24 and AD0.0 P0.23 pins.*/
+
+}