1 files changed, 0 insertions, 128 deletions
diff --git a/boards/ST_STM3210C_EVAL/board.h b/boards/ST_STM3210C_EVAL/board.h
deleted file mode 100644
index 2193179b8..000000000
--- a/boards/ST_STM3210C_EVAL/board.h
+++ /dev/null
@@ -1,128 +0,0 @@
-/*
-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for the STMicroelectronics STM3210C-EVAL evaluation board.
- */
-
-#define GPIOD_LED1              7
-#define GPIOD_LED2              13
-#define GPIOD_LED3              3
-#define GPIOD_LED4              4
-
-/*
- * Board identifier.
- */
-#define BOARD_ST_STM3210C_EVAL
-#define BOARD_NAME              "ST STM3210C-EVAL"
-
-/*
- * Board frequencies.
- */
-#define STM32_LSECLK            32768
-#define STM32_HSECLK            25000000
-
-/*
- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
- */
-#define STM32F10X_CL
-
-/*
- * IO pins assignments.
- * *********************TO BE COMPLETED*********************
- */
-
-/*
- * I/O ports initial setup, this configuration is established soon after reset
- * in the initialization code.
- *
- * The digits have the following meaning:
- *   0 - Analog input.
- *   1 - Push Pull output 10MHz.
- *   2 - Push Pull output 2MHz.
- *   3 - Push Pull output 50MHz.
- *   4 - Digital input.
- *   5 - Open Drain output 10MHz.
- *   6 - Open Drain output 2MHz.
- *   7 - Open Drain output 50MHz.
- *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
- *   9 - Alternate Push Pull output 10MHz.
- *   A - Alternate Push Pull output 2MHz.
- *   B - Alternate Push Pull output 50MHz.
- *   C - Reserved.
- *   D - Alternate Open Drain output 10MHz.
- *   E - Alternate Open Drain output 2MHz.
- *   F - Alternate Open Drain output 50MHz.
- * Please refer to the STM32 Reference Manual for details.
- */
-
-/*
- * Port A setup.
- * Everything input except:
- */
-#define VAL_GPIOACRL            0x44444444      /*  PA7...PA0 */
-#define VAL_GPIOACRH            0x44444444      /* PA15...PA8 */
-#define VAL_GPIOAODR            0xFFFFFFFF
-
-/*
- * Port B setup.
- * Everything input except:
- */
-#define VAL_GPIOBCRL            0x44444444      /*  PB7...PB0 */
-#define VAL_GPIOBCRH            0x44444444      /* PB15...PB8 */
-#define VAL_GPIOBODR            0xFFFFFFFF
-
-/*
- * Port C setup.
- * Everything input except:
- */
-#define VAL_GPIOCCRL            0x44444444      /*  PC7...PC0 */
-#define VAL_GPIOCCRH            0x44444444      /* PC15...PC8 */
-#define VAL_GPIOCODR            0xFFFFFFFF
-
-/*
- * Port D setup.
- * Everything input except:
- * PD5 - USART2TX (remapped) AF PP Output
- * PD6 - USART2RX (remapped) Digital Input
- * PD7 - LED (LD1) PP Output
- */
-#define VAL_GPIODCRL            0x34B33444      /*  PD7...PD0 */
-#define VAL_GPIODCRH            0x44344444      /* PD15...PD8 */
-#define VAL_GPIODODR            0x0000DF67
-
-/*
- * Port E setup.
- * Everything input except:
- */
-#define VAL_GPIOECRL            0x44444444      /*  PE7...PE0 */
-#define VAL_GPIOECRH            0x44344444      /* PE15...PE8 */
-#define VAL_GPIOEODR            0xFFFFFFFF
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
-  void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */