1 files changed, 0 insertions, 121 deletions
diff --git a/boards/ST_STM8S_DISCOVERY/board.h b/boards/ST_STM8S_DISCOVERY/board.h
deleted file mode 100644
index 70e8682da..000000000
--- a/boards/ST_STM8S_DISCOVERY/board.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
-    ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for STMicroelectronics STM8S-Discovery board.
- */
-
-/*
- * Board identifiers.
- */
-#define BOARD_ST_STM8S_DISCOVERY
-#define BOARD_NAME      "ST STM8S-Discovery"
-
-/*
- * Board frequencies.
- */
-#define HSECLK          16000000
-
-/*
- * MCU model used on the board.
- */
-#define STM8S105
-
-/*
- * Pin definitions.
- */
-#define PA_OSCIN        1
-#define PA_OSCOUT       2
-
-#define PC_TS_KEY       1
-#define PC_TS_LOADREF   2
-#define PC_TS_SHIELD    3
-
-#define PD_LD10         0
-#define PD_SWIM         1
-#define PD_TX           5
-#define PD_RX           6
-
-/*
- * Port A initial setup.
- */
-#define VAL_GPIOAODR    0
-#define VAL_GPIOADDR    0               /* All inputs.                      */
-#define VAL_GPIOACR1    0xFF            /* All pull-up or push-pull.        */
-#define VAL_GPIOACR2    0
-
-/*
- * Port B initial setup.
- */
-#define VAL_GPIOBODR    0
-#define VAL_GPIOBDDR    0               /* All inputs.                      */
-#define VAL_GPIOBCR1    0xFF            /* All push-pull.                   */
-#define VAL_GPIOBCR2    0
-
-/*
- * Port C initial setup.
- */
-#define VAL_GPIOCODR    0
-#define VAL_GPIOCDDR    0               /* All inputs.                      */
-#define VAL_GPIOCCR1    0xFF            /* All pull-up.                     */
-#define VAL_GPIOCCR2    0
-
-/*
- * Port D initial setup.
- */
-#define VAL_GPIODODR    (1 << PD_LD10) | (1 << PD_TX)
-#define VAL_GPIODDDR    (1 << PD_LD10) | (1 << PD_TX)
-#define VAL_GPIODCR1    0xFF            /* All pull-up.                     */
-#define VAL_GPIODCR2    0
-
-/*
- * Port E initial setup.
- */
-#define VAL_GPIOEODR    0 
-#define VAL_GPIOEDDR    0               /* All inputs.                      */
-#define VAL_GPIOECR1    0xFF            /* All pull-up.                     */
-#define VAL_GPIOECR2    0
-
-/*
- * Port F initial setup.
- */
-#define VAL_GPIOFODR    0
-#define VAL_GPIOFDDR    0               /* All inputs.                      */
-#define VAL_GPIOFCR1    0xFF            /* All pull-up.                     */
-#define VAL_GPIOFCR2    0
-
-/*
- * Port G initial setup.
- */
-#define VAL_GPIOGODR    0
-#define VAL_GPIOGDDR    0               /* All inputs.                      */
-#define VAL_GPIOGCR1    0xFF            /* All pull-up or push-pull.        */
-#define VAL_GPIOGCR2    0
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
-  void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */