diff options
Diffstat (limited to 'boards/ST_STM8S_DISCOVERY')
| -rw-r--r-- | boards/ST_STM8S_DISCOVERY/board.c | 78 | ||||
| -rw-r--r-- | boards/ST_STM8S_DISCOVERY/board.h | 121 |
2 files changed, 0 insertions, 199 deletions
diff --git a/boards/ST_STM8S_DISCOVERY/board.c b/boards/ST_STM8S_DISCOVERY/board.c deleted file mode 100644 index 33e1fa1e9..000000000 --- a/boards/ST_STM8S_DISCOVERY/board.c +++ /dev/null @@ -1,78 +0,0 @@ -/*
- ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#include "ch.h"
-#include "hal.h"
-
-/**
- * @brief PAL setup.
- * @details Digital I/O ports static configuration as defined in @p board.h.
- */
-#if HAL_USE_PAL || defined(__DOXYGEN__)
-ROMCONST PALConfig pal_default_config =
-{
- {
- {VAL_GPIOAODR, 0, VAL_GPIOADDR, VAL_GPIOACR1, VAL_GPIOACR2},
- {VAL_GPIOBODR, 0, VAL_GPIOBDDR, VAL_GPIOBCR1, VAL_GPIOBCR2},
- {VAL_GPIOCODR, 0, VAL_GPIOCDDR, VAL_GPIOCCR1, VAL_GPIOCCR2},
- {VAL_GPIODODR, 0, VAL_GPIODDDR, VAL_GPIODCR1, VAL_GPIODCR2},
- {VAL_GPIOEODR, 0, VAL_GPIOEDDR, VAL_GPIOECR1, VAL_GPIOECR2},
- {VAL_GPIOFODR, 0, VAL_GPIOFDDR, VAL_GPIOFCR1, VAL_GPIOFCR2},
- {VAL_GPIOGODR, 0, VAL_GPIOGDDR, VAL_GPIOGCR1, VAL_GPIOGCR2},
- }
-};
-#endif
-
-/*
- * TIM 2 clock after the prescaler.
- */
-#define TIM2_CLOCK (SYSCLK / 16)
-#define TIM2_ARR ((TIM2_CLOCK / CH_FREQUENCY) - 1)
-
-/*
- * TIM2 interrupt handler.
- */
-CH_IRQ_HANDLER(13) {
-
- CH_IRQ_PROLOGUE();
-
- chSysLockFromIsr();
- chSysTimerHandlerI();
- chSysUnlockFromIsr();
-
- TIM2->SR1 = 0;
-
- CH_IRQ_EPILOGUE();
-}
-
-/*
- * Board-specific initialization code.
- */
-void boardInit(void) {
-
- /*
- * TIM2 initialization as system tick.
- */
- CLK->PCKENR1 |= CLK_PCKENR1_TIM2;
- TIM2->PSCR = 4; /* Prescaler divide by 2^4=16.*/
- TIM2->ARRH = (uint8_t)(TIM2_ARR >> 8);
- TIM2->ARRL = (uint8_t)(TIM2_ARR);
- TIM2->CNTRH = 0;
- TIM2->CNTRL = 0;
- TIM2->SR1 = 0;
- TIM2->IER = TIM2_IER_UIE;
- TIM2->CR1 = TIM2_CR1_CEN;
-}
diff --git a/boards/ST_STM8S_DISCOVERY/board.h b/boards/ST_STM8S_DISCOVERY/board.h deleted file mode 100644 index 70e8682da..000000000 --- a/boards/ST_STM8S_DISCOVERY/board.h +++ /dev/null @@ -1,121 +0,0 @@ -/*
- ChibiOS/RT - Copyright (C) 2006-2013 Giovanni Di Sirio
-
- Licensed under the Apache License, Version 2.0 (the "License");
- you may not use this file except in compliance with the License.
- You may obtain a copy of the License at
-
- http://www.apache.org/licenses/LICENSE-2.0
-
- Unless required by applicable law or agreed to in writing, software
- distributed under the License is distributed on an "AS IS" BASIS,
- WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- See the License for the specific language governing permissions and
- limitations under the License.
-*/
-
-#ifndef _BOARD_H_
-#define _BOARD_H_
-
-/*
- * Setup for STMicroelectronics STM8S-Discovery board.
- */
-
-/*
- * Board identifiers.
- */
-#define BOARD_ST_STM8S_DISCOVERY
-#define BOARD_NAME "ST STM8S-Discovery"
-
-/*
- * Board frequencies.
- */
-#define HSECLK 16000000
-
-/*
- * MCU model used on the board.
- */
-#define STM8S105
-
-/*
- * Pin definitions.
- */
-#define PA_OSCIN 1
-#define PA_OSCOUT 2
-
-#define PC_TS_KEY 1
-#define PC_TS_LOADREF 2
-#define PC_TS_SHIELD 3
-
-#define PD_LD10 0
-#define PD_SWIM 1
-#define PD_TX 5
-#define PD_RX 6
-
-/*
- * Port A initial setup.
- */
-#define VAL_GPIOAODR 0
-#define VAL_GPIOADDR 0 /* All inputs. */
-#define VAL_GPIOACR1 0xFF /* All pull-up or push-pull. */
-#define VAL_GPIOACR2 0
-
-/*
- * Port B initial setup.
- */
-#define VAL_GPIOBODR 0
-#define VAL_GPIOBDDR 0 /* All inputs. */
-#define VAL_GPIOBCR1 0xFF /* All push-pull. */
-#define VAL_GPIOBCR2 0
-
-/*
- * Port C initial setup.
- */
-#define VAL_GPIOCODR 0
-#define VAL_GPIOCDDR 0 /* All inputs. */
-#define VAL_GPIOCCR1 0xFF /* All pull-up. */
-#define VAL_GPIOCCR2 0
-
-/*
- * Port D initial setup.
- */
-#define VAL_GPIODODR (1 << PD_LD10) | (1 << PD_TX)
-#define VAL_GPIODDDR (1 << PD_LD10) | (1 << PD_TX)
-#define VAL_GPIODCR1 0xFF /* All pull-up. */
-#define VAL_GPIODCR2 0
-
-/*
- * Port E initial setup.
- */
-#define VAL_GPIOEODR 0
-#define VAL_GPIOEDDR 0 /* All inputs. */
-#define VAL_GPIOECR1 0xFF /* All pull-up. */
-#define VAL_GPIOECR2 0
-
-/*
- * Port F initial setup.
- */
-#define VAL_GPIOFODR 0
-#define VAL_GPIOFDDR 0 /* All inputs. */
-#define VAL_GPIOFCR1 0xFF /* All pull-up. */
-#define VAL_GPIOFCR2 0
-
-/*
- * Port G initial setup.
- */
-#define VAL_GPIOGODR 0
-#define VAL_GPIOGDDR 0 /* All inputs. */
-#define VAL_GPIOGCR1 0xFF /* All pull-up or push-pull. */
-#define VAL_GPIOGCR2 0
-
-#if !defined(_FROM_ASM_)
-#ifdef __cplusplus
-extern "C" {
-#endif
- void boardInit(void);
-#ifdef __cplusplus
-}
-#endif
-#endif /* _FROM_ASM_ */
-
-#endif /* _BOARD_H_ */
|