1 files changed, 0 insertions, 76 deletions
diff --git a/demos/KINETIS/RT-FREEDOM-KL25Z/mcuconf.h b/demos/KINETIS/RT-FREEDOM-KL25Z/mcuconf.h
deleted file mode 100644
index 986d324e0..000000000
--- a/demos/KINETIS/RT-FREEDOM-KL25Z/mcuconf.h
+++ /dev/null
@@ -1,76 +0,0 @@
-/*
-    ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio
-
-    Licensed under the Apache License, Version 2.0 (the "License");
-    you may not use this file except in compliance with the License.
-    You may obtain a copy of the License at
-
-        http://www.apache.org/licenses/LICENSE-2.0
-
-    Unless required by applicable law or agreed to in writing, software
-    distributed under the License is distributed on an "AS IS" BASIS,
-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-    See the License for the specific language governing permissions and
-    limitations under the License.
-*/
-
-#ifndef MCUCONF_H
-#define MCUCONF_H
-
-/*
- * STM32F0xx drivers configuration.
- * The following settings override the default settings present in
- * the various device driver implementation headers.
- * Note that the settings for each driver only have effect if the whole
- * driver is enabled in halconf.h.
- *
- * IRQ priorities:
- * 3...0       Lowest...Highest.
- *
- * DMA priorities:
- * 0...3        Lowest...Highest.
- */
-
-#define KL2x_MCUCONF
-
-/*
- * HAL driver system settings.
- */
-
-/* Select the MCU clocking mode below by enabling the appropriate block. */
-
-/* FEI mode */
-#if 0
-#define KINETIS_MCG_MODE            KINETIS_MCG_MODE_FEI
-#define KINETIS_SYSCLK_FREQUENCY    21000000UL
-#endif /* 0 */
-
-/* FEE mode - 24 MHz with external 32.768 kHz crystal */
-#if 0
-#define KINETIS_MCG_MODE            KINETIS_MCG_MODE_FEE
-#define KINETIS_MCG_FLL_DMX32       1           /* Fine-tune for 32.768 kHz */
-#define KINETIS_MCG_FLL_DRS         0           /* 732x FLL factor */
-#define KINETIS_MCG_FLL_OUTDIV1     1           /* Divide 48 MHz FLL by 1 => 24 MHz */
-#define KINETIS_MCG_FLL_OUTDIV4     2           /* Divide OUTDIV1 output by 2 => 12 MHz */
-#define KINETIS_SYSCLK_FREQUENCY    23986176UL  /* 32.768 kHz*732 (~24 MHz) */
-#define KINETIS_UART0_CLOCK_FREQ    (32768 * 732) /* FLL output */
-#define KINETIS_UART0_CLOCK_SRC     1           /* Select FLL clock */
-#define KINETIS_BUSCLK_FREQUENCY    (KINETIS_SYSCLK_FREQUENCY / KINETIS_MCG_FLL_OUTDIV4)
-#endif /* 0 */
-
-/* FEE mode - 48 MHz */
-#if 0
-#define KINETIS_MCG_MODE            KINETIS_MCG_MODE_FEE
-#define KINETIS_MCG_FLL_DMX32       1           /* Fine-tune for 32.768 kHz */
-#define KINETIS_MCG_FLL_DRS         1           /* 1464x FLL factor */
-#define KINETIS_MCG_FLL_OUTDIV1     1           /* Divide 48 MHz FLL by 1 => 48 MHz */
-#define KINETIS_MCG_FLL_OUTDIV4     2           /* Divide OUTDIV1 output by 2 => 24 MHz */
-#define KINETIS_SYSCLK_FREQUENCY    47972352UL  /* 32.768 kHz * 1464 (~48 MHz) */
-#endif /* 0 */
-
-/*
- * SERIAL driver system settings.
- */
-#define KINETIS_SERIAL_USE_UART0              TRUE
-
-#endif /* MCUCONF_H */