From efbd7db9789c18e465750646d51a5fab936c5fc6 Mon Sep 17 00:00:00 2001 From: gdisirio Date: Mon, 22 Oct 2012 17:46:59 +0000 Subject: git-svn-id: svn://svn.code.sf.net/p/chibios/svn/trunk@4776 35acf78f-673a-0410-8e92-d51de3d6d3f4 --- os/hal/platforms/STM32F3xx/stm32f30x.h | 6206 ++++++++++++++++++++++++++++++++ 1 file changed, 6206 insertions(+) create mode 100644 os/hal/platforms/STM32F3xx/stm32f30x.h (limited to 'os/hal/platforms/STM32F3xx/stm32f30x.h') diff --git a/os/hal/platforms/STM32F3xx/stm32f30x.h b/os/hal/platforms/STM32F3xx/stm32f30x.h new file mode 100644 index 000000000..8ca340f48 --- /dev/null +++ b/os/hal/platforms/STM32F3xx/stm32f30x.h @@ -0,0 +1,6206 @@ +/** + ****************************************************************************** + * @file stm32f30x.h + * @author MCD Application Team + * @version V1.0.0 + * @date 04-September-2012 + * @brief CMSIS Cortex-M4 Device Peripheral Access Layer Header File. + * This file contains all the peripheral registers definitions, bits + * definitions and memory mapping for STM32F30x devices. + * + * The file is the unique include file that the application programmer + * is using in the C source code, usually in main.c. This file contains: + * - Configuration section that allows to select: + * - The device used in the target application + * - To use or not the peripheral’s drivers in application code(i.e. + * code will be based on direct access to peripheral’s registers + * rather than drivers API), this option is controlled by + * "#define USE_STDPERIPH_DRIVER" + * - To change few application-specific parameters such as the HSE + * crystal frequency + * - Data structures and the address mapping for all peripherals + * - Peripheral registers declarations and bits definition + * - Macros to access peripheral registers hardware + * + ****************************************************************************** + * @attention + * + *

© COPYRIGHT 2012 STMicroelectronics

+ * + * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); + * You may not use this file except in compliance with the License. + * You may obtain a copy of the License at: + * + * http://www.st.com/software_license_agreement_liberty_v2 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + ****************************************************************************** + */ + +/** @addtogroup CMSIS + * @{ + */ + +/** @addtogroup stm32f30x + * @{ + */ + +#ifndef __STM32F30x_H +#define __STM32F30x_H + +#ifdef __cplusplus + extern "C" { +#endif /* __cplusplus */ + +/** @addtogroup Library_configuration_section + * @{ + */ + +/* Uncomment the line below according to the target STM32 device used in your + application + */ + +#if !defined (STM32F30X) + #define STM32F30X +#endif + +/* Tip: To avoid modifying this file each time you need to switch between these + devices, you can define the device in your toolchain compiler preprocessor. + */ + +#if !defined (STM32F30X) + #error "Please select first the target STM32F30X device used in your application (in stm32f30x.h file)" +#endif + +#if !defined (USE_STDPERIPH_DRIVER) +/** + * @brief Comment the line below if you will not use the peripherals drivers. + In this case, these drivers will not be included and the application code will + be based on direct access to peripherals registers + */ + /*#define USE_STDPERIPH_DRIVER*/ +#endif /* USE_STDPERIPH_DRIVER */ + +/** + * @brief In the following line adjust the value of External High Speed oscillator (HSE) + used in your application + + Tip: To avoid modifying this file each time you need to use different HSE, you + can define the HSE value in your toolchain compiler preprocessor. + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +/** + * @brief In the following line adjust the External High Speed oscillator (HSE) Startup + Timeout value + */ +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSE start up */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup + Timeout value + */ +#if !defined (HSI_STARTUP_TIMEOUT) + #define HSI_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSI start up */ +#endif /* HSI_STARTUP_TIMEOUT */ + +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)8000000) +#endif /* HSI_VALUE */ /*!< Value of the Internal High Speed oscillator in Hz. + The real value may vary depending on the variations + in voltage and temperature. */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)40000) +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + + +/** + * @brief STM32F30x Standard Peripherals Library version number V1.0.0 + */ +#define __STM32F30X_STDPERIPH_VERSION_MAIN (0x01) /*!< [31:24] main version */ +#define __STM32F30X_STDPERIPH_VERSION_SUB1 (0x00) /*!< [23:16] sub1 version */ +#define __STM32F30X_STDPERIPH_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */ +#define __STM32F30X_STDPERIPH_VERSION_RC (0x00) /*!< [7:0] release candidate */ +#define __STM32F30X_STDPERIPH_VERSION ( (__STM32F30X_STDPERIPH_VERSION_MAIN << 24)\ + |(__STM32F30X_STDPERIPH_VERSION_SUB1 << 16)\ + |(__STM32F30X_STDPERIPH_VERSION_SUB2 << 8)\ + |(__STM32F30X_STDPERIPH_VERSION_RC)) + +/** + * @} + */ + +/** @addtogroup Configuration_section_for_CMSIS + * @{ + */ + +/** + * @brief Configuration of the Cortex-M4 Processor and Core Peripherals + */ +#define __CM4_REV 0x0001 /*!< Core revision r0p1 */ +#define __MPU_PRESENT 1 /*!< STM32F30X provide an MPU */ +#define __NVIC_PRIO_BITS 4 /*!< STM32F30X uses 4 Bits for the Priority Levels */ +#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */ +#define __FPU_PRESENT 1 /*!< STM32F30X provide an FPU */ + + +/** + * @brief STM32F30X Interrupt Number Definition, according to the selected device + * in @ref Library_configuration_section + */ +typedef enum IRQn +{ +/****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/ + NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */ + MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */ + BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */ + UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */ + SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */ + DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */ + PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */ + SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */ +/****** STM32 specific Interrupt Numbers **********************************************************************/ + WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */ + PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */ + TAMPER_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts */ + RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI lines 17, 19 & 20 */ + FLASH_IRQn = 4, /*!< FLASH global Interrupt */ + RCC_IRQn = 5, /*!< RCC global Interrupt */ + EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */ + EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */ + EXTI2_TS_IRQn = 8, /*!< EXTI Line2 Interrupt and Touch Sense Interrupt */ + EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */ + EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */ + DMA1_Channel1_IRQn = 11, /*!< DMA1 Channel 1 Interrupt */ + DMA1_Channel2_IRQn = 12, /*!< DMA1 Channel 2 Interrupt */ + DMA1_Channel3_IRQn = 13, /*!< DMA1 Channel 3 Interrupt */ + DMA1_Channel4_IRQn = 14, /*!< DMA1 Channel 4 Interrupt */ + DMA1_Channel5_IRQn = 15, /*!< DMA1 Channel 5 Interrupt */ + DMA1_Channel6_IRQn = 16, /*!< DMA1 Channel 6 Interrupt */ + DMA1_Channel7_IRQn = 17, /*!< DMA1 Channel 7 Interrupt */ + ADC1_2_IRQn = 18, /*!< ADC1 & ADC2 Interrupts */ + USB_HP_CAN1_TX_IRQn = 19, /*!< USB Device High Priority or CAN1 TX Interrupts */ + USB_LP_CAN1_RX0_IRQn = 20, /*!< USB Device Low Priority or CAN1 RX0 Interrupts */ + CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */ + CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */ + EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */ + TIM1_BRK_TIM15_IRQn = 24, /*!< TIM1 Break and TIM15 Interrupts */ + TIM1_UP_TIM16_IRQn = 25, /*!< TIM1 Update and TIM16 Interrupts */ + TIM1_TRG_COM_TIM17_IRQn = 26, /*!< TIM1 Trigger and Commutation and TIM17 Interrupt */ + TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */ + TIM2_IRQn = 28, /*!< TIM2 global Interrupt */ + TIM3_IRQn = 29, /*!< TIM3 global Interrupt */ + TIM4_IRQn = 30, /*!< TIM4 global Interrupt */ + I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */ + I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */ + I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */ + I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */ + SPI1_IRQn = 35, /*!< SPI1 global Interrupt */ + SPI2_IRQn = 36, /*!< SPI2 global Interrupt */ + USART1_IRQn = 37, /*!< USART1 global Interrupt */ + USART2_IRQn = 38, /*!< USART2 global Interrupt */ + USART3_IRQn = 39, /*!< USART3 global Interrupt */ + EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */ + RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */ + USBWakeUp_IRQn = 42, /*!< USB Wakeup Interrupt */ + TIM8_BRK_IRQn = 43, /*!< TIM8 Break Interrupt */ + TIM8_UP_IRQn = 44, /*!< TIM8 Update Interrupt */ + TIM8_TRG_COM_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt */ + TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */ + ADC3_IRQn = 47, /*!< ADC3 global Interrupt */ + SPI3_IRQn = 51, /*!< SPI3 global Interrupt */ + UART4_IRQn = 52, /*!< UART4 global Interrupt */ + UART5_IRQn = 53, /*!< UART5 global Interrupt */ + TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */ + TIM7_IRQn = 55, /*!< TIM7 global Interrupt */ + DMA2_Channel1_IRQn = 56, /*!< DMA2 Channel 1 global Interrupt */ + DMA2_Channel2_IRQn = 57, /*!< DMA2 Channel 2 global Interrupt */ + DMA2_Channel3_IRQn = 58, /*!< DMA2 Channel 3 global Interrupt */ + DMA2_Channel4_IRQn = 59, /*!< DMA2 Channel 4 global Interrupt */ + DMA2_Channel5_IRQn = 60, /*!< DMA2 Channel 5 global Interrupt */ + ADC4_IRQn = 61, /*!< ADC4 global Interrupt */ + COMP1_2_3_IRQn = 64, /*!< COMP1, COMP2 and COMP3 global Interrupt */ + COMP4_5_6_IRQn = 65, /*!< COMP5, COMP6 and COMP4 global Interrupt */ + COMP7_IRQn = 66, /*!< COMP7 global Interrupt */ + USB_HP_IRQn = 74, /*!< USB High Priority global Interrupt remap */ + USB_LP_IRQn = 75, /*!< USB Low Priority global Interrupt remap */ + USBWakeUp_RMP_IRQn = 76, /*!< USB Wakeup Interrupt remap */ + FPU_IRQn = 81 /*!< Floating point Interrupt */ +} IRQn_Type; + +/** + * @} + */ + +#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */ +/* CHIBIOS FIX */ +/*#include "system_stm32f30x.h"*/ /* STM32F30x System Header */ +#include + +/** @addtogroup Exported_types + * @{ + */ +/*!< STM32F10x Standard Peripheral Library old types (maintained for legacy purpose) */ +typedef int32_t s32; +typedef int16_t s16; +typedef int8_t s8; + +typedef const int32_t sc32; /*!< Read Only */ +typedef const int16_t sc16; /*!< Read Only */ +typedef const int8_t sc8; /*!< Read Only */ + +typedef __IO int32_t vs32; +typedef __IO int16_t vs16; +typedef __IO int8_t vs8; + +typedef __I int32_t vsc32; /*!< Read Only */ +typedef __I int16_t vsc16; /*!< Read Only */ +typedef __I int8_t vsc8; /*!< Read Only */ + +typedef uint32_t u32; +typedef uint16_t u16; +typedef uint8_t u8; + +typedef const uint32_t uc32; /*!< Read Only */ +typedef const uint16_t uc16; /*!< Read Only */ +typedef const uint8_t uc8; /*!< Read Only */ + +typedef __IO uint32_t vu32; +typedef __IO uint16_t vu16; +typedef __IO uint8_t vu8; + +typedef __I uint32_t vuc32; /*!< Read Only */ +typedef __I uint16_t vuc16; /*!< Read Only */ +typedef __I uint8_t vuc8; /*!< Read Only */ + +typedef enum {RESET = 0, SET = !RESET} FlagStatus, ITStatus; + +typedef enum {DISABLE = 0, ENABLE = !DISABLE} FunctionalState; +#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE)) + +typedef enum {ERROR = 0, SUCCESS = !ERROR} ErrorStatus; + +/** + * @} + */ + +/** @addtogroup Peripheral_registers_structures + * @{ + */ + +/** + * @brief Analog to Digital Converter + */ + +typedef struct +{ + __IO uint32_t ISR; /*!< ADC Interrupt and Status Register, Address offset: 0x00 */ + __IO uint32_t IER; /*!< ADC Interrupt Enable Register, Address offset: 0x04 */ + __IO uint32_t CR; /*!< ADC control register, Address offset: 0x08 */ + __IO uint32_t CFGR; /*!< ADC Configuration register, Address offset: 0x0C */ + uint32_t RESERVED0; /*!< Reserved, 0x010 */ + __IO uint32_t SMPR1; /*!< ADC sample time register 1, Address offset: 0x14 */ + __IO uint32_t SMPR2; /*!< ADC sample time register 2, Address offset: 0x18 */ + uint32_t RESERVED1; /*!< Reserved, 0x01C */ + __IO uint32_t TR1; /*!< ADC watchdog threshold register 1, Address offset: 0x20 */ + __IO uint32_t TR2; /*!< ADC watchdog threshold register 2, Address offset: 0x24 */ + __IO uint32_t TR3; /*!< ADC watchdog threshold register 3, Address offset: 0x28 */ + uint32_t RESERVED2; /*!< Reserved, 0x02C */ + __IO uint32_t SQR1; /*!< ADC regular sequence register 1, Address offset: 0x30 */ + __IO uint32_t SQR2; /*!< ADC regular sequence register 2, Address offset: 0x34 */ + __IO uint32_t SQR3; /*!< ADC regular sequence register 3, Address offset: 0x38 */ + __IO uint32_t SQR4; /*!< ADC regular sequence register 4, Address offset: 0x3C */ + __IO uint32_t DR; /*!< ADC regular data register, Address offset: 0x40 */ + uint32_t RESERVED3; /*!< Reserved, 0x044 */ + uint32_t RESERVED4; /*!< Reserved, 0x048 */ + __IO uint32_t JSQR; /*!< ADC injected sequence register, Address offset: 0x4C */ + uint32_t RESERVED5[4]; /*!< Reserved, 0x050 - 0x05C */ + __IO uint32_t OFR1; /*!< ADC offset register 1, Address offset: 0x60 */ + __IO uint32_t OFR2; /*!< ADC offset register 2, Address offset: 0x64 */ + __IO uint32_t OFR3; /*!< ADC offset register 3, Address offset: 0x68 */ + __IO uint32_t OFR4; /*!< ADC offset register 4, Address offset: 0x6C */ + uint32_t RESERVED6[4]; /*!< Reserved, 0x070 - 0x07C */ + __IO uint32_t JDR1; /*!< ADC injected data register 1, Address offset: 0x80 */ + __IO uint32_t JDR2; /*!< ADC injected data register 2, Address offset: 0x84 */ + __IO uint32_t JDR3; /*!< ADC injected data register 3, Address offset: 0x88 */ + __IO uint32_t JDR4; /*!< ADC injected data register 4, Address offset: 0x8C */ + uint32_t RESERVED7[4]; /*!< Reserved, 0x090 - 0x09C */ + __IO uint32_t AWD2CR; /*!< ADC Analog Watchdog 2 Configuration Register, Address offset: 0xA0 */ + __IO uint32_t AWD3CR; /*!< ADC Analog Watchdog 3 Configuration Register, Address offset: 0xA4 */ + uint32_t RESERVED8; /*!< Reserved, 0x0A8 */ + uint32_t RESERVED9; /*!< Reserved, 0x0AC */ + __IO uint32_t DIFSEL; /*!< ADC Differential Mode Selection Register, Address offset: 0xB0 */ + __IO uint32_t CALFACT; /*!< ADC Calibration Factors, Address offset: 0xB4 */ + +} ADC_TypeDef; + +typedef struct +{ + __IO uint32_t CSR; /*!< ADC Common status register, Address offset: ADC1/3 base address + 0x300 */ + uint32_t RESERVED; /*!< Reserved, ADC1/3 base address + 0x304 */ + __IO uint32_t CCR; /*!< ADC common control register, Address offset: ADC1/3 base address + 0x308 */ + __IO uint32_t CDR; /*!< ADC common regular data register for dual + AND triple modes, Address offset: ADC1/3 base address + 0x30C */ +} ADC_Common_TypeDef; + + +/** + * @brief Controller Area Network TxMailBox + */ +typedef struct +{ + __IO uint32_t TIR; /*!< CAN TX mailbox identifier register */ + __IO uint32_t TDTR; /*!< CAN mailbox data length control and time stamp register */ + __IO uint32_t TDLR; /*!< CAN mailbox data low register */ + __IO uint32_t TDHR; /*!< CAN mailbox data high register */ +} CAN_TxMailBox_TypeDef; + +/** + * @brief Controller Area Network FIFOMailBox + */ +typedef struct +{ + __IO uint32_t RIR; /*!< CAN receive FIFO mailbox identifier register */ + __IO uint32_t RDTR; /*!< CAN receive FIFO mailbox data length control and time stamp register */ + __IO uint32_t RDLR; /*!< CAN receive FIFO mailbox data low register */ + __IO uint32_t RDHR; /*!< CAN receive FIFO mailbox data high register */ +} CAN_FIFOMailBox_TypeDef; + +/** + * @brief Controller Area Network FilterRegister + */ +typedef struct +{ + __IO uint32_t FR1; /*!< CAN Filter bank register 1 */ + __IO uint32_t FR2; /*!< CAN Filter bank register 1 */ +} CAN_FilterRegister_TypeDef; + +/** + * @brief Controller Area Network + */ +typedef struct +{ + __IO uint32_t MCR; /*!< CAN master control register, Address offset: 0x00 */ + __IO uint32_t MSR; /*!< CAN master status register, Address offset: 0x04 */ + __IO uint32_t TSR; /*!< CAN transmit status register, Address offset: 0x08 */ + __IO uint32_t RF0R; /*!< CAN receive FIFO 0 register, Address offset: 0x0C */ + __IO uint32_t RF1R; /*!< CAN receive FIFO 1 register, Address offset: 0x10 */ + __IO uint32_t IER; /*!< CAN interrupt enable register, Address offset: 0x14 */ + __IO uint32_t ESR; /*!< CAN error status register, Address offset: 0x18 */ + __IO uint32_t BTR; /*!< CAN bit timing register, Address offset: 0x1C */ + uint32_t RESERVED0[88]; /*!< Reserved, 0x020 - 0x17F */ + CAN_TxMailBox_TypeDef sTxMailBox[3]; /*!< CAN Tx MailBox, Address offset: 0x180 - 0x1AC */ + CAN_FIFOMailBox_TypeDef sFIFOMailBox[2]; /*!< CAN FIFO MailBox, Address offset: 0x1B0 - 0x1CC */ + uint32_t RESERVED1[12]; /*!< Reserved, 0x1D0 - 0x1FF */ + __IO uint32_t FMR; /*!< CAN filter master register, Address offset: 0x200 */ + __IO uint32_t FM1R; /*!< CAN filter mode register, Address offset: 0x204 */ + uint32_t RESERVED2; /*!< Reserved, 0x208 */ + __IO uint32_t FS1R; /*!< CAN filter scale register, Address offset: 0x20C */ + uint32_t RESERVED3; /*!< Reserved, 0x210 */ + __IO uint32_t FFA1R; /*!< CAN filter FIFO assignment register, Address offset: 0x214 */ + uint32_t RESERVED4; /*!< Reserved, 0x218 */ + __IO uint32_t FA1R; /*!< CAN filter activation register, Address offset: 0x21C */ + uint32_t RESERVED5[8]; /*!< Reserved, 0x220-0x23F */ + CAN_FilterRegister_TypeDef sFilterRegister[28]; /*!< CAN Filter Register, Address offset: 0x240-0x31C */ +} CAN_TypeDef; + + +/** + * @brief Analog Comparators + */ + +typedef struct +{ + __IO uint32_t CSR; /*!< Comparator control Status register, Address offset: 0x00 */ +} COMP_TypeDef; + +/** + * @brief CRC calculation unit + */ + +typedef struct +{ + __IO uint32_t DR; /*!< CRC Data register, Address offset: 0x00 */ + __IO uint8_t IDR; /*!< CRC Independent data register, Address offset: 0x04 */ + uint8_t RESERVED0; /*!< Reserved, 0x05 */ + uint16_t RESERVED1; /*!< Reserved, 0x06 */ + __IO uint32_t CR; /*!< CRC Control register, Address offset: 0x08 */ + uint32_t RESERVED2; /*!< Reserved, 0x0C */ + __IO uint32_t INIT; /*!< Initial CRC value register, Address offset: 0x10 */ + __IO uint32_t POL; /*!< CRC polynomial register, Address offset: 0x14 */ +} CRC_TypeDef; + +/** + * @brief Digital to Analog Converter + */ + +typedef struct +{ + __IO uint32_t CR; /*!< DAC control register, Address offset: 0x00 */ + __IO uint32_t SWTRIGR; /*!< DAC software trigger register, Address offset: 0x04 */ + __IO uint32_t DHR12R1; /*!< DAC channel1 12-bit right-aligned data holding register, Address offset: 0x08 */ + __IO uint32_t DHR12L1; /*!< DAC channel1 12-bit left aligned data holding register, Address offset: 0x0C */ + __IO uint32_t DHR8R1; /*!< DAC channel1 8-bit right aligned data holding register, Address offset: 0x10 */ + __IO uint32_t DHR12R2; /*!< DAC channel2 12-bit right aligned data holding register, Address offset: 0x14 */ + __IO uint32_t DHR12L2; /*!< DAC channel2 12-bit left aligned data holding register, Address offset: 0x18 */ + __IO uint32_t DHR8R2; /*!< DAC channel2 8-bit right-aligned data holding register, Address offset: 0x1C */ + __IO uint32_t DHR12RD; /*!< Dual DAC 12-bit right-aligned data holding register, Address offset: 0x20 */ + __IO uint32_t DHR12LD; /*!< DUAL DAC 12-bit left aligned data holding register, Address offset: 0x24 */ + __IO uint32_t DHR8RD; /*!< DUAL DAC 8-bit right aligned data holding register, Address offset: 0x28 */ + __IO uint32_t DOR1; /*!< DAC channel1 data output register, Address offset: 0x2C */ + __IO uint32_t DOR2; /*!< DAC channel2 data output register, Address offset: 0x30 */ + __IO uint32_t SR; /*!< DAC status register, Address offset: 0x34 */ +} DAC_TypeDef; + +/** + * @brief Debug MCU + */ + +typedef struct +{ + __IO uint32_t IDCODE; /*!< MCU device ID code, Address offset: 0x00 */ + __IO uint32_t CR; /*!< Debug MCU configuration register, Address offset: 0x04 */ + __IO uint32_t APB1FZ; /*!< Debug MCU APB1 freeze register, Address offset: 0x08 */ + __IO uint32_t APB2FZ; /*!< Debug MCU APB2 freeze register, Address offset: 0x0C */ +}DBGMCU_TypeDef; + +/** + * @brief DMA Controller + */ + +typedef struct +{ + __IO uint32_t CCR; /*!< DMA channel x configuration register */ + __IO uint32_t CNDTR; /*!< DMA channel x number of data register */ + __IO uint32_t CPAR; /*!< DMA channel x peripheral address register */ + __IO uint32_t CMAR; /*!< DMA channel x memory address register */ +} DMA_Channel_TypeDef; + +typedef struct +{ + __IO uint32_t ISR; /*!< DMA interrupt status register, Address offset: 0x00 */ + __IO uint32_t IFCR; /*!< DMA interrupt clear flag register, Address offset: 0x04 */ +} DMA_TypeDef; + +/** + * @brief External Interrupt/Event Controller + */ + +typedef struct +{ + __IO uint32_t IMR; /*!< EXTI Interrupt mask register, Address offset: 0x00 */ + __IO uint32_t EMR; /*!< EXTI Event mask register, Address offset: 0x04 */ + __IO uint32_t RTSR; /*!< EXTI Rising trigger selection register, Address offset: 0x08 */ + __IO uint32_t FTSR; /*!< EXTI Falling trigger selection register, Address offset: 0x0C */ + __IO uint32_t SWIER; /*!< EXTI Software interrupt event register, Address offset: 0x10 */ + __IO uint32_t PR; /*!< EXTI Pending register, Address offset: 0x14 */ + uint32_t RESERVED1; /*!< Reserved, 0x18 */ + uint32_t RESERVED2; /*!< Reserved, 0x1C */ + __IO uint32_t IMR2; /*!< EXTI Interrupt mask register, Address offset: 0x20 */ + __IO uint32_t EMR2; /*!< EXTI Event mask register, Address offset: 0x24 */ + __IO uint32_t RTSR2; /*!< EXTI Rising trigger selection register, Address offset: 0x28 */ + __IO uint32_t FTSR2; /*!< EXTI Falling trigger selection register, Address offset: 0x2C */ + __IO uint32_t SWIER2; /*!< EXTI Software interrupt event register, Address offset: 0x30 */ + __IO uint32_t PR2; /*!< EXTI Pending register, Address offset: 0x34 */ +}EXTI_TypeDef; + +/** + * @brief FLASH Registers + */ + +typedef struct +{ + __IO uint32_t ACR; /*!< FLASH access control register, Address offset: 0x00 */ + __IO uint32_t KEYR; /*!< FLASH key register, Address offset: 0x04 */ + __IO uint32_t OPTKEYR; /*!< FLASH option key register, Address offset: 0x08 */ + __IO uint32_t SR; /*!< FLASH status register, Address offset: 0x0C */ + __IO uint32_t CR; /*!< FLASH control register, Address offset: 0x10 */ + __IO uint32_t AR; /*!< FLASH address register, Address offset: 0x14 */ + uint32_t RESERVED; /*!< Reserved, 0x18 */ + __IO uint32_t OBR; /*!< FLASH Option byte register, Address offset: 0x1C */ + __IO uint32_t WRPR; /*!< FLASH Write register, Address offset: 0x20 */ + +} FLASH_TypeDef; + +/** + * @brief Option Bytes Registers + */ +typedef struct +{ + __IO uint16_t RDP; /*!