aboutsummaryrefslogtreecommitdiffstats
path: root/converter/m0110_usb/Makefile.tmk_rev2
diff options
context:
space:
mode:
Diffstat (limited to 'converter/m0110_usb/Makefile.tmk_rev2')
-rw-r--r--converter/m0110_usb/Makefile.tmk_rev296
1 files changed, 0 insertions, 96 deletions
diff --git a/converter/m0110_usb/Makefile.tmk_rev2 b/converter/m0110_usb/Makefile.tmk_rev2
deleted file mode 100644
index e83645632..000000000
--- a/converter/m0110_usb/Makefile.tmk_rev2
+++ /dev/null
@@ -1,96 +0,0 @@
-# Target file name (without extension).
-TARGET = m0110_lufa
-
-# Directory common source filess exist
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC = matrix.c \
- led.c \
- keymap_common.c \
- m0110.c
-
-# To use own keymap file run make like: make keymap=hasu
-ifdef KEYMAP
- SRC += keymap_$(KEYMAP).c
-else
- SRC += keymap_default.c
-endif
-
-CONFIG_H = config.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-MCU = atmega32u2 # TMK converter rev2
-#MCU = atmega32u4 # TMK converter rev1
-
-
-# Processor frequency.
-# Normally the first thing your program should do is set the clock prescaler,
-# so your program will run at the correct speed. You should also set this
-# variable to same clock speed. The _delay_ms() macro uses this, and many
-# examples use this variable to calculate timings. Do not add a "UL" here.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in bytes
-# Teensy halfKay 512
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# *Comment out* to disable the options.
-#
-#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
-#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
-
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TMK_DIR)
-
-
-include $(TMK_DIR)/protocol/lufa.mk
-include $(TMK_DIR)/protocol.mk
-include $(TMK_DIR)/common.mk
-include $(TMK_DIR)/rules.mk