aboutsummaryrefslogtreecommitdiffstats
path: root/keyboards/ergodox/infinity/infinity.c
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/ergodox/infinity/infinity.c')
-rw-r--r--keyboards/ergodox/infinity/infinity.c195
1 files changed, 195 insertions, 0 deletions
diff --git a/keyboards/ergodox/infinity/infinity.c b/keyboards/ergodox/infinity/infinity.c
new file mode 100644
index 000000000..62259ed3f
--- /dev/null
+++ b/keyboards/ergodox/infinity/infinity.c
@@ -0,0 +1,195 @@
+#include "infinity.h"
+#include "ch.h"
+#include "hal.h"
+#include "serial_link/system/serial_link.h"
+#ifdef VISUALIZER_ENABLE
+#include "lcd_backlight.h"
+#endif
+
+void init_serial_link_hal(void) {
+ PORTA->PCR[1] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(2);
+ PORTA->PCR[2] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(2);
+ PORTE->PCR[0] = PORTx_PCRn_PE | PORTx_PCRn_PS | PORTx_PCRn_PFE | PORTx_PCRn_MUX(3);
+ PORTE->PCR[1] = PORTx_PCRn_DSE | PORTx_PCRn_SRE | PORTx_PCRn_MUX(3);
+}
+
+#define RED_PIN 1
+#define GREEN_PIN 2
+#define BLUE_PIN 3
+#define CHANNEL_RED FTM0->CHANNEL[0]
+#define CHANNEL_GREEN FTM0->CHANNEL[1]
+#define CHANNEL_BLUE FTM0->CHANNEL[2]
+
+#define RGB_PORT PORTC
+#define RGB_PORT_GPIO GPIOC
+
+// Base FTM clock selection (72 MHz system clock)
+// @ 0xFFFF period, 72 MHz / (0xFFFF * 2) = Actual period
+// Higher pre-scalar will use the most power (also look the best)
+// Pre-scalar calculations
+// 0 - 72 MHz -> 549 Hz
+// 1 - 36 MHz -> 275 Hz
+// 2 - 18 MHz -> 137 Hz
+// 3 - 9 MHz -> 69 Hz (Slightly visible flicker)
+// 4 - 4 500 kHz -> 34 Hz (Visible flickering)
+// 5 - 2 250 kHz -> 17 Hz
+// 6 - 1 125 kHz -> 9 Hz
+// 7 - 562 500 Hz -> 4 Hz
+// Using a higher pre-scalar without flicker is possible but FTM0_MOD will need to be reduced
+// Which will reduce the brightness range
+#define PRESCALAR_DEFINE 0
+void lcd_backlight_hal_init(void) {
+ // Setup Backlight
+ SIM->SCGC6 |= SIM_SCGC6_FTM0;
+ FTM0->CNT = 0; // Reset counter
+
+ // PWM Period
+ // 16-bit maximum
+ FTM0->MOD = 0xFFFF;
+
+ // Set FTM to PWM output - Edge Aligned, Low-true pulses
+#define CNSC_MODE FTM_SC_CPWMS | FTM_SC_PS(4) | FTM_SC_CLKS(0)
+ CHANNEL_RED.CnSC = CNSC_MODE;
+ CHANNEL_GREEN.CnSC = CNSC_MODE;
+ CHANNEL_BLUE.CnSC = CNSC_MODE;
+
+ // System clock, /w prescalar setting
+ FTM0->SC = FTM_SC_CLKS(1) | FTM_SC_PS(PRESCALAR_DEFINE);
+
+ CHANNEL_RED.CnV = 0;
+ CHANNEL_GREEN.CnV = 0;
+ CHANNEL_BLUE.CnV = 0;
+
+ RGB_PORT_GPIO->PDDR |= (1 << RED_PIN);
+ RGB_PORT_GPIO->PDDR |= (1 << GREEN_PIN);
+ RGB_PORT_GPIO->PDDR |= (1 << BLUE_PIN);
+
+#define RGB_MODE PORTx_PCRn_SRE | PORTx_PCRn_DSE | PORTx_PCRn_MUX(4)
+ RGB_PORT->PCR[RED_PIN] = RGB_MODE;
+ RGB_PORT->PCR[GREEN_PIN] = RGB_MODE;
+ RGB_PORT->PCR[BLUE_PIN] = RGB_MODE;
+}
+
+static uint16_t cie_lightness(uint16_t v) {
+ // The CIE 1931 formula for lightness
+ // Y = luminance (output) 0-1
+ // L = lightness input 0 - 100
+
+ // Y = (L* / 902.3) if L* <= 8
+ // Y = ((L* + 16) / 116)^3 if L* > 8
+
+ float l = 100.0f * (v / 65535.0f);
+ float y = 0.0f;
+ if (l <= 8.0f) {
+ y = l / 902.3;
+ }
+ else {
+ y = ((l + 16.0f) / 116.0f);
+ y = y * y * y;
+ if (y > 1.0f) {
+ y = 1.0f;
+ }
+ }
+ return y * 65535.0f;
+}
+
+void lcd_backlight_hal_color(uint16_t r, uint16_t g, uint16_t b) {
+ CHANNEL_RED.CnV = cie_lightness(r);
+ CHANNEL_GREEN.CnV = cie_lightness(g);
+ CHANNEL_BLUE.CnV = cie_lightness(b);
+}
+
+__attribute__ ((weak))
+void matrix_init_user(void) {
+}
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+
+void matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+
+ matrix_init_user();
+ // The backlight always has to be initialized, otherwise it will stay lit
+#ifndef VISUALIZER_ENABLE
+ lcd_backlight_hal_init();
+#endif
+}
+
+void matrix_scan_kb(void) {
+ // put your looping keyboard code here
+ // runs every cycle (a lot)
+
+ matrix_scan_user();
+}
+
+__attribute__ ((weak))
+void ergodox_board_led_on(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_1_on(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_2_on(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_3_on(void){
+}
+
+__attribute__ ((weak))
+void ergodox_board_led_off(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_1_off(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_2_off(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_3_off(void){
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_1_set(uint8_t n) {
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_2_set(uint8_t n) {
+}
+
+__attribute__ ((weak))
+void ergodox_right_led_3_set(uint8_t n) {
+}
+
+#ifdef ONEHAND_ENABLE
+__attribute__ ((weak))
+const keypos_t hand_swap_config[MATRIX_ROWS][MATRIX_COLS] = {
+ {{0, 9}, {1, 9}, {2, 9}, {3, 9}, {4, 9}},
+ {{0, 10}, {1, 10}, {2, 10}, {3, 10}, {4, 10}},
+ {{0, 11}, {1, 11}, {2, 11}, {3, 11}, {4, 11}},
+ {{0, 12}, {1, 12}, {2, 12}, {3, 12}, {4, 12}},
+ {{0, 13}, {1, 13}, {2, 13}, {3, 13}, {4, 13}},
+ {{0, 14}, {1, 14}, {2, 14}, {3, 14}, {4, 14}},
+ {{0, 15}, {1, 15}, {2, 15}, {3, 15}, {4, 15}},
+ {{0, 16}, {1, 16}, {2, 16}, {3, 16}, {4, 16}},
+ {{0, 17}, {1, 17}, {2, 17}, {3, 17}, {4, 17}},
+ {{0, 0}, {1, 0}, {2, 0}, {3, 0}, {4, 0}},
+ {{0, 1}, {1, 1}, {2, 1}, {3, 1}, {4, 1}},
+ {{0, 2}, {1, 2}, {2, 2}, {3, 2}, {4, 2}},
+ {{0, 3}, {1, 3}, {2, 3}, {3, 3}, {4, 3}},
+ {{0, 4}, {1, 4}, {2, 4}, {3, 4}, {4, 4}},
+ {{0, 5}, {1, 5}, {2, 5}, {3, 5}, {4, 5}},
+ {{0, 6}, {1, 6}, {2, 6}, {3, 6}, {4, 6}},
+ {{0, 7}, {1, 7}, {2, 7}, {3, 7}, {4, 7}},
+ {{0, 8}, {1, 8}, {2, 8}, {3, 8}, {4, 8}},
+};
+#endif