From 60ed0b7c3045d9511c28495f4d8c65240434c952 Mon Sep 17 00:00:00 2001
From: MechMerlin <30334081+mechmerlin@users.noreply.github.com>
Date: Sat, 3 Nov 2018 15:09:32 -0700
Subject: Keyboard: Port over the x268 Noxary Firmware (#4339)

* port over Rozakiin https://github.com/Rozakiin/Noxary_Firmware/tree/master/noxary_x268

* rename LAYOUT to LAYOUT_65_ansi default layout

* add configurator support

* add community layout support

* put Rozakiin's name everywhere

* update readme

* problems with the 65_ansi keymap to be diagnosed later
---
 keyboards/noxary/x268/rules.mk | 80 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
 create mode 100644 keyboards/noxary/x268/rules.mk

(limited to 'keyboards/noxary/x268/rules.mk')

diff --git a/keyboards/noxary/x268/rules.mk b/keyboards/noxary/x268/rules.mk
new file mode 100644
index 000000000..3c4a26ad1
--- /dev/null
+++ b/keyboards/noxary/x268/rules.mk
@@ -0,0 +1,80 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Bootloader selection
+#   Teensy       halfkay
+#   Pro Micro    caterina
+#   Atmel DFU    atmel-dfu
+#   LUFA DFU     lufa-dfu
+#   QMK DFU      qmk-dfu
+#   atmega32a    bootloadHID
+BOOTLOADER = atmel-dfu
+
+
+# If you don't know the bootloader type, then you can specify the
+# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
+#   Teensy halfKay      512
+#   Teensy++ halfKay    1024
+#   Atmel DFU loader    4096
+#   LUFA bootloader     4096
+#   USBaspLoader        2048
+# OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no        # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes            # USB Nkey Rollover
+BACKLIGHT_ENABLE = yes       # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = yes        # Enable keyboard RGB underglow
+MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no           # Audio output on port C6
+FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no 		# Enable support for HD44780 based LCDs (+400)
-- 
cgit v1.2.3