# MCU name MCU = atmega32u4 # Processor frequency. # This will define a symbol, F_CPU, in all source code files equal to the # processor frequency in Hz. You can then use this symbol in your source code to # calculate timings. Do NOT tack on a 'UL' at the end, this will be done # automatically to create a 32-bit value in your source code. # # This will be an integer division of F_USB below, as it is sourced by # F_USB after it has run through any CPU prescalers. Note that this value # does not *change* the processor frequency - it should merely be updated to # reflect the processor speed set externally so that the code can use accurate # software delays. F_CPU = 16000000 # # LUFA specific # # Target architecture (see library "Board Types" documentation). ARCH = AVR8 # Input clock frequency. # This will define a symbol, F_USB, in all source code files equal to the # input clock frequency (before any prescaling is performed) in Hz. This value may # differ from F_CPU if prescaling is used on the latter, and is required as the # raw input clock is fed directly to the PLL sections of the AVR for high speed # clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' # at the end, this will be done automatically to create a 32-bit value in your # source code. # # If no clock division is performed on the input clock inside the AVR (via the # CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. F_USB = $(F_CPU) # Interrupt driven control endpoint task(+60) OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT # Boot Section Size in *bytes* OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options # change yes to no to disable # BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) MOUSEKEY_ENABLE = yes # Mouse keys(+4700) EXTRAKEY_ENABLE = yes # Audio control and System control(+450) CONSOLE_ENABLE = no # Console for debug(+400) COMMAND_ENABLE = no # Commands for debug and configuration SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend NKRO_ENABLE = yes # USB Nkey Rollover BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default MIDI_ENABLE = no # MIDI controls UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 LAYOUTS = planck_mit ortho_4x12 LAYOUTS_HAS_RGB = no d=fc0af42eb82bf94a9b1174d3ba96536238bc5fcd'>DOCS/vt102-ug/table6-7.html
blob: 43331c7c5dd388894a17f75aac3e1c8b72b6f6c6 (plain) 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146