diff options
Diffstat (limited to 'Demos/Host/ClassDriver/StillImageHost/makefile')
| -rw-r--r-- | Demos/Host/ClassDriver/StillImageHost/makefile | 77 |
1 files changed, 47 insertions, 30 deletions
diff --git a/Demos/Host/ClassDriver/StillImageHost/makefile b/Demos/Host/ClassDriver/StillImageHost/makefile index f36d9f278..626d6e685 100644 --- a/Demos/Host/ClassDriver/StillImageHost/makefile +++ b/Demos/Host/ClassDriver/StillImageHost/makefile @@ -71,28 +71,21 @@ BOARD = USBKEY # Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency. You can then use this symbol in your source code to
+# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
-# Typical values are:
-# F_CPU = 1000000
-# F_CPU = 1843200
-# F_CPU = 2000000
-# F_CPU = 3686400
-# F_CPU = 4000000
-# F_CPU = 7372800
-# F_CPU = 8000000
-# F_CPU = 11059200
-# F_CPU = 14745600
-# F_CPU = 16000000
-# F_CPU = 18432000
-# F_CPU = 20000000
+#
+# This will be an integer division of F_CLOCK below, as it is sourced by
+# F_CLOCK after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
F_CPU = 8000000
# Input clock frequency.
# This will define a symbol, F_CLOCK, in all source code files equal to the
-# input clock frequency (before any prescaling is performed). This value may
+# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
@@ -461,7 +454,7 @@ ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS) # Default target.
-all: begin gccversion sizebefore build showeventhooks showliboptions showtarget sizeafter end
+all: begin gccversion sizebefore build checkinvalidevents showliboptions showtarget sizeafter end
# Change the build target to build a HEX file or a library.
build: elf hex eep lss sym
@@ -504,14 +497,17 @@ sizeafter: @if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \
2>/dev/null; echo; fi
-showeventhooks: build
- @echo
- @echo -------- Unhooked LUFA Events --------
- @$(shell) (grep -s '^EVENT_.*LUFA/.*\\.o' $(TARGET).map | \
- cut -d' ' -f1 | cut -d'_' -f2- | grep ".*") || \
- echo "(None)"
- @echo --------------------------------------
+$(LUFA_PATH)/LUFA/LUFA_Events.lst:
+ @make -C $(LUFA_PATH)/LUFA/ LUFA_Events.lst
+checkinvalidevents: $(LUFA_PATH)/LUFA/LUFA_Events.lst
+ @echo
+ @echo Checking for invalid events...
+ @$(shell) avr-nm $(TARGET).elf | sed -n -e 's/^.*EVENT_/EVENT_/p' | \
+ grep -F -v --file=$(LUFA_PATH)/LUFA/LUFA_Events.lst > InvalidEvents.tmp || true
+ @sed -n -e 's/^/ WARNING - INVALID EVENT NAME: /p' InvalidEvents.tmp
+ @if test -s InvalidEvents.tmp; then exit 1; fi
+
showliboptions:
@echo
@echo ---- Compile Time Library Options ----
@@ -528,16 +524,37 @@ showtarget: @echo Clock: $(F_CPU)Hz CPU, $(F_CLOCK)Hz Master
@echo --------------------------------------
+
# Display compiler version information.
gccversion :
@$(CC) --version
-
# Program the device.
program: $(TARGET).hex $(TARGET).eep
$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+flip: $(TARGET).hex
+ batchisp -hardware usb -device $(MCU) -operation erase f
+ batchisp -hardware usb -device $(MCU) -operation loadbuffer $(TARGET).hex program
+ batchisp -hardware usb -device $(MCU) -operation start reset 0
+
+dfu: $(TARGET).hex
+ dfu-programmer $(MCU) erase
+ dfu-programmer $(MCU) flash --debug 1 $(TARGET).hex
+ dfu-programmer $(MCU) reset
+
+flip-ee: $(TARGET).hex $(TARGET).eep
+ $(COPY) $(TARGET).eep $(TARGET)eep.hex
+ batchisp -hardware usb -device $(MCU) -operation memory EEPROM erase
+ batchisp -hardware usb -device $(MCU) -operation memory EEPROM loadbuffer $(TARGET)eep.hex program
+ batchisp -hardware usb -device $(MCU) -operation start reset 0
+ $(REMOVE) $(TARGET)eep.hex
+
+dfu-ee: $(TARGET).hex $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
+ dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
@@ -692,9 +709,9 @@ clean_list: $(REMOVE) $(SRC:.c=.s)
$(REMOVE) $(SRC:.c=.d)
$(REMOVE) $(SRC:.c=.i)
+ $(REMOVE) InvalidEvents.tmp
$(REMOVEDIR) .dep
-
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@@ -712,8 +729,8 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) # Listing of phony targets.
-.PHONY : all showeventhooks showliboptions showtarget \
-begin finish end sizebefore sizeafter gccversion build \
-elf hex eep lss sym coff extcoff program clean debug \
-clean_list clean_binary gdb-config doxygen dfu flip \
-flip-ee dfu-ee
\ No newline at end of file +.PHONY : all checkinvalidevents showliboptions \
+showtarget begin finish end sizebefore sizeafter \
+gccversion build elf hex eep lss sym coff extcoff \
+program dfu flip flip-ee dfu-ee clean debug \
+clean_list clean_binary gdb-config doxygen
\ No newline at end of file |