diff options
Diffstat (limited to 'Demos')
28 files changed, 150 insertions, 117 deletions
diff --git a/Demos/AudioInput/makefile b/Demos/AudioInput/makefile index 51f6cc5b8..697442b5e 100644 --- a/Demos/AudioInput/makefile +++ b/Demos/AudioInput/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/AudioOutput/makefile b/Demos/AudioOutput/makefile index 6c2ee3230..a84a4b58b 100644 --- a/Demos/AudioOutput/makefile +++ b/Demos/AudioOutput/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/BluetoothHost/BluetoothHost.c b/Demos/BluetoothHost/BluetoothHost.c index 0f9eb4a9e..50bd1a8fe 100644 --- a/Demos/BluetoothHost/BluetoothHost.c +++ b/Demos/BluetoothHost/BluetoothHost.c @@ -62,9 +62,9 @@ TASK_LIST Bluetooth_Device_t Bluetooth_DeviceConfiguration =
{
- Class: (DEVICE_CLASS_SERVICE_CAPTURING | DEVICE_CLASS_MAJOR_COMPUTER | DEVICE_CLASS_MINOR_COMPUTER_PALM),
+ Class: (DEVICE_CLASS_SERVICE_CAPTURING | DEVICE_CLASS_MAJOR_COMPUTER | DEVICE_CLASS_MINOR_COMPUTER_PALM),
PINCode: "0000",
- Name: "LUFA Bluetooth Demo"
+ Name: "LUFA Bluetooth Demo"
};
diff --git a/Demos/BluetoothHost/makefile b/Demos/BluetoothHost/makefile index 189c84e1c..0adac4bcd 100644 --- a/Demos/BluetoothHost/makefile +++ b/Demos/BluetoothHost/makefile @@ -540,10 +540,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -677,15 +677,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -698,11 +699,15 @@ clean_list: $(REMOVE) $(SRC:.c=.i)
$(REMOVEDIR) .dep
+
doxygen:
@echo Generating Project Documentation...
@doxygen Doxygen.conf
@echo Documentation Generation Complete.
+clean_doxygen:
+ rm -rf Documentation
+
# Create object files directory
$(shell mkdir $(OBJDIR) 2>/dev/null)
@@ -716,4 +721,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/CDC/makefile b/Demos/CDC/makefile index 9b0e5bdd6..8b19d1dee 100644 --- a/Demos/CDC/makefile +++ b/Demos/CDC/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/CDCHost/makefile b/Demos/CDCHost/makefile index d1e4cb990..98700824c 100644 --- a/Demos/CDCHost/makefile +++ b/Demos/CDCHost/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -674,15 +674,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/DualCDC/makefile b/Demos/DualCDC/makefile index 01ab60997..9313b8008 100644 --- a/Demos/DualCDC/makefile +++ b/Demos/DualCDC/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/Joystick/makefile b/Demos/Joystick/makefile index a29a2d380..6638c108c 100644 --- a/Demos/Joystick/makefile +++ b/Demos/Joystick/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -615,6 +615,8 @@ extcoff: $(TARGET).elf @echo $(MSG_SYMBOL_TABLE) $@
$(NM) -n $< > $@
+
+
# Create library from object files.
.SECONDARY : $(TARGET).a
.PRECIOUS : $(OBJ)
@@ -674,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -712,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/Keyboard/makefile b/Demos/Keyboard/makefile index 681f729e2..db138609a 100644 --- a/Demos/Keyboard/makefile +++ b/Demos/Keyboard/makefile @@ -536,10 +536,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -678,10 +678,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -716,4 +717,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardFullInt/makefile b/Demos/KeyboardFullInt/makefile index b1f7f890f..a7ebbf9fd 100644 --- a/Demos/KeyboardFullInt/makefile +++ b/Demos/KeyboardFullInt/makefile @@ -533,10 +533,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -675,10 +675,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -713,4 +714,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardHost/makefile b/Demos/KeyboardHost/makefile index 7ff737e51..6ef376b33 100644 --- a/Demos/KeyboardHost/makefile +++ b/Demos/KeyboardHost/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -674,15 +674,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardHostViaInt/makefile b/Demos/KeyboardHostViaInt/makefile index a8b3f23e6..813ed690c 100644 --- a/Demos/KeyboardHostViaInt/makefile +++ b/Demos/KeyboardHostViaInt/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -674,15 +674,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardHostWithParser/makefile b/Demos/KeyboardHostWithParser/makefile index ea768b4e4..41d8d9f66 100644 --- a/Demos/KeyboardHostWithParser/makefile +++ b/Demos/KeyboardHostWithParser/makefile @@ -539,10 +539,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,15 +676,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -719,4 +720,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardMouse/makefile b/Demos/KeyboardMouse/makefile index 7c26d2cf2..b16146c28 100644 --- a/Demos/KeyboardMouse/makefile +++ b/Demos/KeyboardMouse/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/KeyboardViaInt/makefile b/Demos/KeyboardViaInt/makefile index ff225b35c..5b84843b6 100644 --- a/Demos/KeyboardViaInt/makefile +++ b/Demos/KeyboardViaInt/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MIDI/makefile b/Demos/MIDI/makefile index c5cc048d8..7d9f24a05 100644 --- a/Demos/MIDI/makefile +++ b/Demos/MIDI/makefile @@ -534,10 +534,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,10 +676,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -714,4 +715,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MassStorage/makefile b/Demos/MassStorage/makefile index 2f17228af..284d2aa28 100644 --- a/Demos/MassStorage/makefile +++ b/Demos/MassStorage/makefile @@ -536,10 +536,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -678,10 +678,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -716,4 +717,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MassStorageHost/makefile b/Demos/MassStorageHost/makefile index 2608b76bb..322d76003 100644 --- a/Demos/MassStorageHost/makefile +++ b/Demos/MassStorageHost/makefile @@ -539,10 +539,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -676,15 +676,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -719,4 +720,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/Mouse/makefile b/Demos/Mouse/makefile index 0f20dca63..4886e8926 100644 --- a/Demos/Mouse/makefile +++ b/Demos/Mouse/makefile @@ -535,10 +535,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -677,10 +677,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -715,4 +716,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MouseFullInt/makefile b/Demos/MouseFullInt/makefile index fe8551698..0a7e684d5 100644 --- a/Demos/MouseFullInt/makefile +++ b/Demos/MouseFullInt/makefile @@ -535,10 +535,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -677,10 +677,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -715,4 +716,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MouseHost/makefile b/Demos/MouseHost/makefile index 6e8688f10..f2bb61ad2 100644 --- a/Demos/MouseHost/makefile +++ b/Demos/MouseHost/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -679,10 +679,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MouseHostViaInt/makefile b/Demos/MouseHostViaInt/makefile index f2b86e12f..45b53c6b3 100644 --- a/Demos/MouseHostViaInt/makefile +++ b/Demos/MouseHostViaInt/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -679,10 +679,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MouseHostWithParser/makefile b/Demos/MouseHostWithParser/makefile index 3eec44b36..c815185f2 100644 --- a/Demos/MouseHostWithParser/makefile +++ b/Demos/MouseHostWithParser/makefile @@ -539,10 +539,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -681,10 +681,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -719,4 +720,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/MouseViaInt/makefile b/Demos/MouseViaInt/makefile index 571d1f606..892fe4417 100644 --- a/Demos/MouseViaInt/makefile +++ b/Demos/MouseViaInt/makefile @@ -535,10 +535,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -677,10 +677,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -715,4 +716,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/RNDISEthernet/makefile b/Demos/RNDISEthernet/makefile index ba1588af6..18f1fe4a8 100644 --- a/Demos/RNDISEthernet/makefile +++ b/Demos/RNDISEthernet/makefile @@ -548,10 +548,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -690,10 +690,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -728,4 +729,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/StillImageHost/makefile b/Demos/StillImageHost/makefile index 63e328ac4..8387c8161 100644 --- a/Demos/StillImageHost/makefile +++ b/Demos/StillImageHost/makefile @@ -537,10 +537,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -674,15 +674,16 @@ $(OBJDIR)/%.o : %.S $(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@
-## Target: clean project.
+# Target: clean project.
clean: begin clean_list clean_binary end
clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -717,4 +718,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/TestApp/makefile b/Demos/TestApp/makefile index befc0e6fc..e3a3ba935 100644 --- a/Demos/TestApp/makefile +++ b/Demos/TestApp/makefile @@ -542,10 +542,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -684,10 +684,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -722,4 +723,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
diff --git a/Demos/USBtoSerial/makefile b/Demos/USBtoSerial/makefile index 6703102bb..0c4aa87e8 100644 --- a/Demos/USBtoSerial/makefile +++ b/Demos/USBtoSerial/makefile @@ -536,10 +536,10 @@ flip-ee: $(TARGET).hex $(TARGET).eep batchisp -hardware usb -device $(MCU) -operation start reset 0
dfu-ee: $(TARGET).hex $(TARGET).eep
- dfu-programmer $(MCU) erase
- dfu-programmer $(MCU) eeprom --debug 1 $(TARGET).eep
+ dfu-programmer $(MCU) flash-eeprom --debug 1 --suppress-bootloader-mem $(TARGET).eep
dfu-programmer $(MCU) reset
+
# Generate avr-gdb config/init file which does the following:
# define the reset signal, load the target file, connect to target, and set
# a breakpoint at main().
@@ -678,10 +678,11 @@ clean: begin clean_list clean_binary end clean_binary:
$(REMOVE) $(TARGET).hex
-
+
clean_list:
@echo $(MSG_CLEANING)
$(REMOVE) $(TARGET).eep
+ $(REMOVE) $(TARGET)eep.hex
$(REMOVE) $(TARGET).cof
$(REMOVE) $(TARGET).elf
$(REMOVE) $(TARGET).map
@@ -716,4 +717,4 @@ $(shell mkdir $(OBJDIR) 2>/dev/null) finish end sizebefore sizeafter gccversion \
build elf hex eep lss sym coff extcoff \
clean clean_list clean_binary program debug \
-gdb-config doxygen dfu flip
+gdb-config doxygen dfu flip flip-ee dfu-ee
|