4 files changed, 7 insertions, 7 deletions
diff --git a/Projects/AVRISP-MKII/Lib/XPROG/TINYNVM.c b/Projects/AVRISP-MKII/Lib/XPROG/TINYNVM.c
index 8d74dd47f..526837cd0 100644
--- a/Projects/AVRISP-MKII/Lib/XPROG/TINYNVM.c
+++ b/Projects/AVRISP-MKII/Lib/XPROG/TINYNVM.c
@@ -151,7 +151,7 @@ void TINYNVM_DisableTPI(void)
 		/* Clear the NVMEN bit in the TPI STATUS register to disable TPI mode */
 		XPROGTarget_SendByte(TPI_CMD_SSTCS | TPI_STATUS_REG);
 		XPROGTarget_SendByte(0x00);
-	
+
 		/* Read back the STATUS register, check to see if it took effect */
 		XPROGTarget_SendByte(TPI_CMD_SLDCS | PDI_RESET_REG);
 	} while (XPROGTarget_ReceiveByte() != 0x00);
diff --git a/Projects/AVRISP-MKII/Lib/XPROG/XMEGANVM.c b/Projects/AVRISP-MKII/Lib/XPROG/XMEGANVM.c
index 71fa78222..d0e6d7335 100644
--- a/Projects/AVRISP-MKII/Lib/XPROG/XMEGANVM.c
+++ b/Projects/AVRISP-MKII/Lib/XPROG/XMEGANVM.c
@@ -149,7 +149,7 @@ void XMEGANVM_DisablePDI(void)
 {
 	XMEGANVM_WaitWhileNVMBusBusy();
 
-	/* Clear the RESET key in the RESET PDI register to allow the XMEGA to run - must perform this until the 
+	/* Clear the RESET key in the RESET PDI register to allow the XMEGA to run - must perform this until the
 	 * change takes effect, as in some cases it takes multiple writes (silicon bug?).
 	 */
 	do
@@ -157,7 +157,7 @@ void XMEGANVM_DisablePDI(void)
 		/* Clear reset register */
 		XPROGTarget_SendByte(PDI_CMD_STCS | PDI_RESET_REG);
 		XPROGTarget_SendByte(0x00);
-	
+
 		/* Read back the reset register, check to see if it took effect */
 		XPROGTarget_SendByte(PDI_CMD_LDCS | PDI_RESET_REG);
 	} while (XPROGTarget_ReceiveByte() != 0x00);
diff --git a/Projects/AVRISP-MKII/Lib/XPROG/XPROGProtocol.c b/Projects/AVRISP-MKII/Lib/XPROG/XPROGProtocol.c
index 72cc53636..132acf154 100644
--- a/Projects/AVRISP-MKII/Lib/XPROG/XPROGProtocol.c
+++ b/Projects/AVRISP-MKII/Lib/XPROG/XPROGProtocol.c
@@ -143,7 +143,7 @@ static void XPROGProtocol_LeaveXPROGMode(void)
 	  TINYNVM_DisableTPI();
 
 	#if defined(XCK_RESCUE_CLOCK_ENABLE) && defined(ENABLE_ISP_PROTOCOL)
-	/* If the XCK rescue clock option is enabled, we need to restart it once the 
+	/* If the XCK rescue clock option is enabled, we need to restart it once the
 	 * XPROG mode has been exited, since the XPROG protocol stops it after use. */
 	ISPTarget_ConfigureRescueClock();
 	#endif
@@ -258,7 +258,7 @@ static void XPROGProtocol_WriteMemory(void)
 		Endpoint_ClearOUT();
 		Endpoint_WaitUntilReady();
 	}
-	
+
 	Endpoint_ClearOUT();
 	Endpoint_SelectEndpoint(AVRISP_DATA_IN_EPNUM);
 	Endpoint_SetEndpointDirection(ENDPOINT_DIR_IN);
diff --git a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c
index 58df78559..0ba3c7674 100644
--- a/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c
+++ b/Projects/AVRISP-MKII/Lib/XPROG/XPROGTarget.c
@@ -120,7 +120,7 @@ void XPROGTarget_DisableTargetTPI(void)
 	/* Set all USART lines as inputs, tristate */
 	DDRD  &= ~((1 << 5) | (1 << 3));
 	PORTD &= ~((1 << 5) | (1 << 3) | (1 << 2));
-	
+
 	/* Tristate target /RESET line */
 	AUX_LINE_DDR  &= ~AUX_LINE_MASK;
 	AUX_LINE_PORT &= ~AUX_LINE_MASK;
@@ -164,7 +164,7 @@ void XPROGTarget_SendIdle(void)
 	/* Switch to Tx mode if currently in Rx mode */
 	if (!(IsSending))
 	  XPROGTarget_SetTxMode();
-	
+
 	/* Need to do nothing for a full frame to send an IDLE */
 	for (uint8_t i = 0; i < BITS_IN_USART_FRAME; i++)
 	{