| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
| |
of the alternative CTC mode via the Input Capture register, to reduce user confusion.
|
|
|
|
| |
using a LRU (Least Recently Used) algorithm to discard the oldest set note when the note table becomes full.
|
|
|
|
| |
up to three simultaneous notes from MIDI channel 0.
|
|
|
|
|
|
| |
port when the USART is busy.
Minor documentation improvements.
|
|
|
|
| |
value to give maximum throughput.
|
|
|
|
| |
projects so that the RAM is not overflowed on the smaller USB AVR targets (thanks to Andrei from Microsin.ru).
|
|
|
|
| |
XPROGTarget_SendIdle(), as it is sending idle bits and not break bits.
|
|
|
|
| |
automatically after exiting TPI programming mode.
|
|
|
|
|
|
| |
issues with the XPLAINBridge when PDI programming at faster rates.
Speed up XMEGANVM_WaitWhileNVMControllerBusy() by preloading the status register address into the pointer register of the target's NVM controller and then reading via a faster indirect load command.
|
|
|
|
| |
clone programmer project (thanks to Tom Light).
|
| |
|
| |
|
|
|
|
| |
instead of the desired 500KHz.
|
|
|
|
| |
endpoint descriptors (thanks to MCS Electronics).
|
|
|
|
|
|
| |
Fixed calculation of timer register reload values derived from F_CPU; must subtract one from the division result for the compare value to be correct.
Change AVRISP-MKII rescue clock speed to 4MHz to ensure that a 125KHz ISP speed works regardless of the target's fuses (i.e. DIV8 set).
|
|
|
|
| |
report descriptor.
|
|
|
|
| |
EVENT_USB_Device_ControlRequest() as it is now fired before the library request handlers, not afterwards.
|
|
|
|
| |
send buffer becomes full.
|
|
|
|
|
|
| |
generation in the AVRISP-MKII clone project.
Change over all low level host mode project's descriptor comparator routines to perform the descriptor casting in a temp variable to make the code clearer and easier to modify (despite being more verbose).
|
|
|
|
| |
clock can be generated at all times when 125KHz ISP programming mode is selected.
|
|
|
|
| |
redirect domain, including the new aliased links for LUFA-related pages such as the various download/source control mirrors and support lists.
|
|
|
|
|
|
|
|
| |
modify all demos to use them where possible.
Move out private/internal host class driver constants to the common class driver headers, so that they can be used in the Low Level host mode demos.
Ensure all demos, projects and bootloaders use the class driver constants where possible to minimise code repetition.
|
|
|
|
|
|
| |
is included, and no longer need to be seperately included.
All LowLevel demos changed to use the constants and types defined in the USB class drivers.
|
|
|
|
| |
recent API changes in the LUFA core.
|
|
|
|
| |
complete in the rest of the XPLAINBridge project code.
|
| |
|
|
|
|
| |
tool made by Laszlo Monda
|
|
|
|
| |
selection constant names.
|
|
|
|
| |
and the AVRISP-MKII ISP modules.
|
|
|
|
| |
CMDEX bit - this appears to be an error in the XMEGA manual external memory programming table.
|
|
|
|
| |
XMEGA targets.
|
|
|
|
| |
writing in non-paged mode and the polling byte cannot be used.
|
|
|
|
|
|
| |
interface's report descriptor size.
Simplified low level Host demo configuration descriptor parser routines.
|
|
|
|
|
|
| |
an invalid interface is discarded.
Update the pipe configuration routines in the host mode class drivers so that they use the same new code to enumerate compatible devices to increase reliability. Add support to the host mode class drivers for non-sequential (but non-overlapping with other interface) pipe numbers.
|
|
|
|
|
|
|
|
|
|
| |
on the configuration order instead to ensure maximum reliability.
Altered all low level device and host mode demos to ensure that endpoints and pipes are configured in ascending order properly.
Rewrote all low level host mode demos' configuration descriptor parser code to ensure that pipes are enumerated in ascending order, and to ensure maximum compatibility with devices.
Incremented all device mode demo's device descriptor revision numbers to ensure that any descriptor changes are re-fetched on machines which have enumerated previous versions.
|
|
|
|
|
|
| |
project so that it defaults to active low drive.
Fixed incorrect USB_DeviceState value when unconfiguring the device without an address set.
|
|
|
|
|
|
|
|
| |
make them more managable.
Add new CDC descriptor structs to the CDC class driver, so that the CDC demos can use human readable field names.
Rename prefix for Still Image Host class driver functions from "SImage_" to "SI_" to remain consistent with the rest of the driver.
|
|
|
|
| |
all dfu-programmer versions.
|
|
|
|
|
|
|
|
| |
ensure that writes to the bootloader section of the AVR's flash memory are ignored (thanks to Axel Rohde).
Fixed incorrect command name for EEPROM memory programming in the makefile dfu-ee target.
Makefile whitespace fixes.
|
|
|
|
| |
assembly and C++ sources (thanks to Daniel Czigany).
|
| |
|
| |
|
| |
|
|
|
|
| |
naming.
|
|
|
|
| |
USB AVR device "series" comprises of.
|
|
|
|
| |
incorrect call to ADC_Init() in the TemperatureDatalogger project.
|
|
|
|
| |
not removed when the GetDescriptor callback function's signature was altered.
|
| |
|
|
|
|
| |
so that the descriptor pointer is const, to remove the need for extra casting inside the callback (thanks to Jonathan Kollasch).
|
|
|
|
|
|
| |
acknowledged, so that long event handlers do do skew the timing of the control requests.
Fixed USBtoSerial and Benito project SetLineEncoding calls failing if the USART is busy, due to the RX ISR delaying the control request handler.
|