From a8b66f318dda3cc18dfcedaa3af3d01ab68b82e8 Mon Sep 17 00:00:00 2001 From: Dean Camera Date: Sun, 26 Dec 2010 14:55:26 +0000 Subject: Documentation improvements - put driver example code into its own section, fix incorrect and missing section names. --- Projects/AVRISP-MKII/AVRISP-MKII.txt | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'Projects/AVRISP-MKII') diff --git a/Projects/AVRISP-MKII/AVRISP-MKII.txt b/Projects/AVRISP-MKII/AVRISP-MKII.txt index 7489cf6a0..fb6411b58 100644 --- a/Projects/AVRISP-MKII/AVRISP-MKII.txt +++ b/Projects/AVRISP-MKII/AVRISP-MKII.txt @@ -6,7 +6,7 @@ /** \mainpage AVRISP MKII Programmer Project * - * \section SSec_Compat Project Compatibility: + * \section Sec_Compat Project Compatibility: * * The following list indicates what microcontrollers are compatible with this project. * @@ -15,7 +15,7 @@ * - Series 4 USB AVRs (ATMEGAxxU4) * - Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - 8KB versions with reduced features only * - * \section SSec_Info USB Information: + * \section Sec_Info USB Information: * * The following table gives a rundown of the USB utilization of this project. * @@ -42,7 +42,7 @@ * * * - * \section SSec_Description Project Description: + * \section Sec_Description Project Description: * * Firmware for an AVRStudio compatible AVRISP-MKII clone programmer. This project will enable the USB AVR series of * microcontrollers to act as a clone of the official Atmel AVRISP-MKII programmer, usable within AVRStudio. In its @@ -109,8 +109,8 @@ * fuses have been mis-set. To use the recovery clock, connect the OCR1A pin of the USB AVR to the target AVR's * XTAL1 pin, and set the ISP programming speed to 125KHz (note: other ISP speeds will not work correctly). * - * 1 Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only \n - * 2 See AUX line related tokens in the \ref SSec_Options section + * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n + * 2 See AUX line related tokens in the \ref Sec_Options section * * \section Sec_PDI PDI Connections * Connections to the device for PDI programming (when enabled): @@ -153,7 +153,7 @@ * * * - * 1 Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only \n + * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n * * \section Sec_TPI TPI Connections @@ -197,11 +197,11 @@ * * * - * 1 Optional, see \ref SSec_Options section - for USB AVRs with ADC modules only \n + * 1 Optional, see \ref Sec_Options section - for USB AVRs with ADC modules only \n * 2 The AVR's Tx and Rx become the DATA line when connected together via a pair of 220 ohm resistors \n - * 3 See AUX line related tokens in the \ref SSec_Options section + * 3 See AUX line related tokens in the \ref Sec_Options section * - * \section SSec_Options Project Options + * \section Sec_Options Project Options * * The following defines can be found in this project, which can control the project behaviour when defined, or changed in value. * -- cgit v1.2.3