From fe47c15b999f45d67e637666bccb472c2adf7dd1 Mon Sep 17 00:00:00 2001 From: Nico Huber Date: Sat, 28 May 2022 14:26:06 +0200 Subject: flashchips: Add Spansion (today Infineon) S25FL128L and S25FL256L These chips seem to be rather regular, supporting 2.7V..3.6V, the common erase block sizes 4KiB, 32KiB, 64KiB and the usual block- protection bits. Status/configuration register naming differs from other vendors, though. These chips have 2 status registers plus 3 configuration registers. Configuration registers 1 & 2 match status registers 2 & 3 of what we are used from other vendors. Read opcodes match too, however writes are always done through the WRSR instruction which can write up to 4 bytes (SR1, CR1, CR2, CR3). S25FL256L supports native 4BA commands and entering a 4BA mode. However, it uses an unusual opcode (0x53) for the 32KiB 4BA block erase. Signed-off-by: Nico Huber Change-Id: I356df6649f29e50879a4da4183f1164a81cb0a09 Reviewed-on: https://review.coreboot.org/c/flashrom/+/64747 Reviewed-by: Thomas Heijligen Tested-by: build bot (Jenkins) --- flashchips.c | 123 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 123 insertions(+) (limited to 'flashchips.c') diff --git a/flashchips.c b/flashchips.c index 0579b79a..4a869b39 100644 --- a/flashchips.c +++ b/flashchips.c @@ -16182,6 +16182,63 @@ const struct flashchip flashchips[] = { .voltage = {2700, 3600}, }, + { + .vendor = "Spansion", + .name = "S25FL128L", + .bustype = BUS_SPI, + .manufacture_id = SPANSION_ID, + .model_id = SPANSION_S25FL128L, + .total_size = 16384, + .page_size = 256, + /* 4 x 256B Security Region (OTP) */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_WRSR_EXT3 | FEATURE_OTP, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 4096} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 512} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 256} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {16384 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {16384 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp2_srwd, + .unlock = spi_disable_blockprotect_bp2_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) supported */ + .voltage = {2700, 3600}, + .reg_bits = + { + /* + * Note: This chip has a read-only Status Register 2 that is not + * counted here. Registers are mapped as follows: + * STATUS1 ... Status Register 1 + * STATUS2 ... Configuration Register 1 + * STATUS3 ... Configuration Register 2 + */ + .srp = {STATUS1, 7, RW}, + .srl = {STATUS2, 0, RW}, + .bp = {{STATUS1, 2, RW}, {STATUS1, 3, RW}, {STATUS1, 4, RW}}, + .tb = {STATUS1, 5, RW}, + .sec = {STATUS1, 6, RW}, + .cmp = {STATUS2, 6, RW}, + .wps = {STATUS3, 2, RW}, + }, + .decode_range = decode_range_spi25, + }, + { .vendor = "Spansion", .name = "S25FL128P......0", /* uniform 64 kB sectors */ @@ -16609,6 +16666,72 @@ const struct flashchip flashchips[] = { .voltage = {2700, 3600}, }, + { + .vendor = "Spansion", + .name = "S25FL256L", + .bustype = BUS_SPI, + .manufacture_id = SPANSION_ID, + .model_id = SPANSION_S25FL256L, + .total_size = 32768, + .page_size = 256, + /* 4 x 256B Security Region (OTP) */ + .feature_bits = FEATURE_WRSR_WREN | FEATURE_WRSR_EXT3 | FEATURE_OTP | + FEATURE_4BA_ENTER | FEATURE_4BA_NATIVE, + .tested = TEST_UNTESTED, + .probe = probe_spi_rdid, + .probe_timing = TIMING_ZERO, + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 8192} }, + .block_erase = spi_block_erase_21, + }, { + .eraseblocks = { {4 * 1024, 8192} }, + .block_erase = spi_block_erase_20, + }, { + .eraseblocks = { {32 * 1024, 1024} }, + .block_erase = spi_block_erase_53, + }, { + .eraseblocks = { {32 * 1024, 1024} }, + .block_erase = spi_block_erase_52, + }, { + .eraseblocks = { {64 * 1024, 512} }, + .block_erase = spi_block_erase_dc, + }, { + .eraseblocks = { {64 * 1024, 512} }, + .block_erase = spi_block_erase_d8, + }, { + .eraseblocks = { {32768 * 1024, 1} }, + .block_erase = spi_block_erase_60, + }, { + .eraseblocks = { {32768 * 1024, 1} }, + .block_erase = spi_block_erase_c7, + } + }, + .printlock = spi_prettyprint_status_register_bp3_srwd, + .unlock = spi_disable_blockprotect_bp3_srwd, + .write = spi_chip_write_256, + .read = spi_chip_read, /* Fast read (0x0B) supported */ + .voltage = {2700, 3600}, + .reg_bits = + { + /* + * Note: This chip has a read-only Status Register 2 that is not + * counted here. Registers are mapped as follows: + * STATUS1 ... Status Register 1 + * STATUS2 ... Configuration Register 1 + * STATUS3 ... Configuration Register 2 + */ + .srp = {STATUS1, 7, RW}, + .srl = {STATUS2, 0, RW}, + .bp = {{STATUS1, 2, RW}, {STATUS1, 3, RW}, {STATUS1, 4, RW}, {STATUS1, 5, RW}}, + .tb = {STATUS1, 6, RW}, + .cmp = {STATUS2, 6, RW}, + .wps = {STATUS3, 2, RW}, + }, + .decode_range = decode_range_spi25, + }, + { .vendor = "Spansion", .name = "S25FL256S Large Sectors", -- cgit v1.2.3