diff options
author | John Crispin <john@openwrt.org> | 2016-02-25 10:14:05 +0000 |
---|---|---|
committer | John Crispin <john@openwrt.org> | 2016-02-25 10:14:05 +0000 |
commit | 0834f9f07631a8857a96614e37cb21e1dc84ffb4 (patch) | |
tree | c62e777de69d8397ed7870991bc46d5648a20046 /target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch | |
parent | b3dc9566a46efa67951ff6ae28e4397da9db92af (diff) | |
download | master-31e0f0ae-0834f9f07631a8857a96614e37cb21e1dc84ffb4.tar.gz master-31e0f0ae-0834f9f07631a8857a96614e37cb21e1dc84ffb4.tar.bz2 master-31e0f0ae-0834f9f07631a8857a96614e37cb21e1dc84ffb4.zip |
brcm2708: remove linux 4.1 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 48766
Diffstat (limited to 'target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch')
-rw-r--r-- | target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch | 3750 |
1 files changed, 0 insertions, 3750 deletions
diff --git a/target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch b/target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch deleted file mode 100644 index 22f74a76a6..0000000000 --- a/target/linux/brcm2708/patches-4.1/0025-BCM2708-Add-core-Device-Tree-support.patch +++ /dev/null @@ -1,3750 +0,0 @@ -From a50362aada2dfc7d76cd18f4a0c238000ec12d2a Mon Sep 17 00:00:00 2001 -From: notro <notro@tronnes.org> -Date: Wed, 9 Jul 2014 14:46:08 +0200 -Subject: [PATCH 025/222] BCM2708: Add core Device Tree support - -Add the bare minimum needed to boot BCM2708 from a Device Tree. - -Signed-off-by: Noralf Tronnes <notro@tronnes.org> - -BCM2708: DT: change 'axi' nodename to 'soc' - -Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835. -The VC4 bootloader fills in certain properties in the 'axi' subtree, -but since this is part of an upstreaming effort, the name is changed. - -Signed-off-by: Noralf Tronnes notro@tronnes.org - -BCM2708_DT: Correct length of the peripheral space ---- - arch/arm/boot/dts/Makefile | 27 ++ - arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 140 ++++++ - arch/arm/boot/dts/bcm2708-rpi-b.dts | 130 ++++++ - arch/arm/boot/dts/bcm2708-rpi-cm.dts | 18 + - arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 51 +++ - arch/arm/boot/dts/bcm2708.dtsi | 19 + - arch/arm/boot/dts/bcm2708_common.dtsi | 230 ++++++++++ - arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 140 ++++++ - arch/arm/boot/dts/bcm2709.dtsi | 70 +++ - arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 45 +- - arch/arm/boot/dts/bcm2835-rpi-b.dts | 29 +- - arch/arm/boot/dts/bcm2835-rpi.dtsi | 97 +++- - arch/arm/boot/dts/bcm2835.dtsi | 45 +- - arch/arm/boot/dts/overlays/Makefile | 57 +++ - arch/arm/boot/dts/overlays/README | 493 +++++++++++++++++++++ - arch/arm/boot/dts/overlays/ads7846-overlay.dts | 83 ++++ - .../dts/overlays/bmp085_i2c-sensor-overlay.dts | 23 + - arch/arm/boot/dts/overlays/dht11-overlay.dts | 39 ++ - arch/arm/boot/dts/overlays/enc28j60-overlay.dts | 50 +++ - .../boot/dts/overlays/hifiberry-amp-overlay.dts | 39 ++ - .../boot/dts/overlays/hifiberry-dac-overlay.dts | 34 ++ - .../dts/overlays/hifiberry-dacplus-overlay.dts | 39 ++ - .../boot/dts/overlays/hifiberry-digi-overlay.dts | 39 ++ - arch/arm/boot/dts/overlays/hy28a-overlay.dts | 87 ++++ - arch/arm/boot/dts/overlays/hy28b-overlay.dts | 142 ++++++ - arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts | 49 ++ - arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts | 13 + - arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts | 39 ++ - .../boot/dts/overlays/iqaudio-dacplus-overlay.dts | 39 ++ - arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts | 57 +++ - .../arm/boot/dts/overlays/mcp2515-can0-overlay.dts | 69 +++ - arch/arm/boot/dts/overlays/mmc-overlay.dts | 19 + - arch/arm/boot/dts/overlays/mz61581-overlay.dts | 109 +++++ - arch/arm/boot/dts/overlays/piscreen-overlay.dts | 96 ++++ - .../dts/overlays/pitft28-resistive-overlay.dts | 115 +++++ - arch/arm/boot/dts/overlays/pps-gpio-overlay.dts | 34 ++ - arch/arm/boot/dts/overlays/rpi-dac-overlay.dts | 34 ++ - arch/arm/boot/dts/overlays/rpi-display-overlay.dts | 82 ++++ - arch/arm/boot/dts/overlays/rpi-proto-overlay.dts | 39 ++ - arch/arm/boot/dts/overlays/sdhost-overlay.dts | 78 ++++ - arch/arm/boot/dts/overlays/spi-bcm2708-overlay.dts | 18 + - arch/arm/boot/dts/overlays/spi-bcm2835-overlay.dts | 18 + - arch/arm/boot/dts/overlays/tinylcd35-overlay.dts | 216 +++++++++ - arch/arm/boot/dts/overlays/w1-gpio-overlay.dts | 39 ++ - .../boot/dts/overlays/w1-gpio-pullup-overlay.dts | 41 ++ - 45 files changed, 3316 insertions(+), 54 deletions(-) - create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b-plus.dts - create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b.dts - create mode 100755 arch/arm/boot/dts/bcm2708-rpi-cm.dts - create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dtsi - create mode 100644 arch/arm/boot/dts/bcm2708.dtsi - create mode 100644 arch/arm/boot/dts/bcm2708_common.dtsi - create mode 100644 arch/arm/boot/dts/bcm2709-rpi-2-b.dts - create mode 100644 arch/arm/boot/dts/bcm2709.dtsi - create mode 100644 arch/arm/boot/dts/overlays/Makefile - create mode 100644 arch/arm/boot/dts/overlays/README - create mode 100644 arch/arm/boot/dts/overlays/ads7846-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/dht11-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/enc28j60-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hy28a-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/hy28b-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts - create mode 100755 arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/mmc-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/mz61581-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/piscreen-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/pps-gpio-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/rpi-dac-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/rpi-display-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/rpi-proto-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/sdhost-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/spi-bcm2708-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/spi-bcm2835-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/tinylcd35-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-overlay.dts - create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -1,5 +1,21 @@ - ifeq ($(CONFIG_OF),y) - -+dtb-$(CONFIG_BCM2708_DT) += bcm2708-rpi-b.dtb -+dtb-$(CONFIG_BCM2708_DT) += bcm2708-rpi-b-plus.dtb -+dtb-$(CONFIG_BCM2708_DT) += bcm2708-rpi-cm.dtb -+dtb-$(CONFIG_BCM2709_DT) += bcm2709-rpi-2-b.dtb -+ -+# Raspberry Pi -+ifeq ($(CONFIG_BCM2708_DT),y) -+ RPI_DT_OVERLAYS=y -+endif -+ifeq ($(CONFIG_BCM2709_DT),y) -+ RPI_DT_OVERLAYS=y -+endif -+ifeq ($(CONFIG_ARCH_BCM2835),y) -+ RPI_DT_OVERLAYS=y -+endif -+ - dtb-$(CONFIG_ARCH_ALPINE) += \ - alpine-db.dtb - dtb-$(CONFIG_MACH_ASM9260) += \ -@@ -660,7 +676,18 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \ - mt6592-evb.dtb \ - mt8127-moose.dtb \ - mt8135-evbp1.dtb -+ -+targets += dtbs dtbs_install -+targets += $(dtb-y) -+ - endif - - always := $(dtb-y) - clean-files := *.dtb -+ -+# Enable fixups to support overlays on BCM2708 platforms -+ifeq ($(RPI_DT_OVERLAYS),y) -+ DTC_FLAGS ?= -@ -+endif -+ -+subdir-y += overlays ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts -@@ -0,0 +1,140 @@ -+/dts-v1/; -+ -+/include/ "bcm2708.dtsi" -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ model = "Raspberry Pi Model B+"; -+ -+ aliases { -+ soc = &soc; -+ spi0 = &spi0; -+ i2c0 = &i2c0; -+ i2c1 = &i2c1; -+ i2s = &i2s; -+ gpio = &gpio; -+ intc = &intc; -+ leds = &leds; -+ audio = &audio; -+ sound = &sound; -+ uart0 = &uart0; -+ uart1 = &uart1; -+ clocks = &clocks; -+ }; -+ -+ sound: sound { -+ }; -+}; -+ -+&gpio { -+ spi0_pins: spi0_pins { -+ brcm,pins = <7 8 9 10 11>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+ -+ i2c0_pins: i2c0 { -+ brcm,pins = <0 1>; -+ brcm,function = <4>; -+ }; -+ -+ i2c1_pins: i2c1 { -+ brcm,pins = <2 3>; -+ brcm,function = <4>; -+ }; -+ -+ i2s_pins: i2s { -+ brcm,pins = <18 19 20 21>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+}; -+ -+&mmc { -+ status = "okay"; -+ bus-width = <4>; -+}; -+ -+&fb { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+&spi0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&spi0_pins>; -+ -+ spidev@0{ -+ compatible = "spidev"; -+ reg = <0>; /* CE0 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+ -+ spidev@1{ -+ compatible = "spidev"; -+ reg = <1>; /* CE1 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+}; -+ -+&i2c0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c0_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2c1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c1_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2s { -+ #sound-dai-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2s_pins>; -+}; -+ -+&leds { -+ act_led: act { -+ label = "led0"; -+ linux,default-trigger = "mmc0"; -+ gpios = <&gpio 47 0>; -+ }; -+ -+ pwr_led: pwr { -+ label = "led1"; -+ linux,default-trigger = "input"; -+ gpios = <&gpio 35 0>; -+ }; -+}; -+ -+/ { -+ __overrides__ { -+ uart0 = <&uart0>,"status"; -+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0"; -+ i2s = <&i2s>,"status"; -+ spi = <&spi0>,"status"; -+ i2c0 = <&i2c0>,"status"; -+ i2c1 = <&i2c1>,"status"; -+ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; -+ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; -+ -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; -+ act_led_trigger = <&act_led>,"linux,default-trigger"; -+ -+ pwr_led_gpio = <&pwr_led>,"gpios:4"; -+ pwr_led_activelow = <&pwr_led>,"gpios:8"; -+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; -+ -+ audio = <&audio>,"status"; -+ watchdog = <&watchdog>,"status"; -+ random = <&random>,"status"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts -@@ -0,0 +1,130 @@ -+/dts-v1/; -+ -+/include/ "bcm2708.dtsi" -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ model = "Raspberry Pi Model B"; -+ -+ aliases { -+ soc = &soc; -+ spi0 = &spi0; -+ i2c0 = &i2c0; -+ i2c1 = &i2c1; -+ i2s = &i2s; -+ gpio = &gpio; -+ intc = &intc; -+ leds = &leds; -+ audio = &audio; -+ sound = &sound; -+ uart0 = &uart0; -+ uart1 = &uart1; -+ clocks = &clocks; -+ }; -+ -+ sound: sound { -+ }; -+}; -+ -+&gpio { -+ spi0_pins: spi0_pins { -+ brcm,pins = <7 8 9 10 11>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+ -+ i2c0_pins: i2c0 { -+ brcm,pins = <0 1>; -+ brcm,function = <4>; -+ }; -+ -+ i2c1_pins: i2c1 { -+ brcm,pins = <2 3>; -+ brcm,function = <4>; -+ }; -+ -+ i2s_pins: i2s { -+ brcm,pins = <28 29 30 31>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+}; -+ -+&mmc { -+ status = "okay"; -+ bus-width = <4>; -+}; -+ -+&fb { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+&spi0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&spi0_pins>; -+ -+ spidev@0{ -+ compatible = "spidev"; -+ reg = <0>; /* CE0 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+ -+ spidev@1{ -+ compatible = "spidev"; -+ reg = <1>; /* CE1 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+}; -+ -+&i2c0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c0_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2c1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c1_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2s { -+ #sound-dai-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2s_pins>; -+}; -+ -+&leds { -+ act_led: act { -+ label = "led0"; -+ linux,default-trigger = "mmc0"; -+ gpios = <&gpio 16 1>; -+ }; -+}; -+ -+/ { -+ __overrides__ { -+ uart0 = <&uart0>,"status"; -+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0"; -+ i2s = <&i2s>,"status"; -+ spi = <&spi0>,"status"; -+ i2c0 = <&i2c0>,"status"; -+ i2c1 = <&i2c1>,"status"; -+ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; -+ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; -+ -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; -+ act_led_trigger = <&act_led>,"linux,default-trigger"; -+ -+ audio = <&audio>,"status"; -+ watchdog = <&watchdog>,"status"; -+ random = <&random>,"status"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts -@@ -0,0 +1,18 @@ -+/dts-v1/; -+ -+/include/ "bcm2708-rpi-cm.dtsi" -+ -+/ { -+ model = "Raspberry Pi Compute Module"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+/ { -+ __overrides__ { -+ uart0 = <&uart0>,"status"; -+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi -@@ -0,0 +1,51 @@ -+/include/ "bcm2708.dtsi" -+ -+/ { -+ aliases { -+ soc = &soc; -+ spi0 = &spi0; -+ i2c0 = &i2c0; -+ i2c1 = &i2c1; -+ i2s = &i2s; -+ gpio = &gpio; -+ intc = &intc; -+ leds = &leds; -+ audio = &audio; -+ sound = &sound; -+ uart0 = &uart0; -+ uart1 = &uart1; -+ clocks = &clocks; -+ }; -+ -+ sound: sound { -+ }; -+}; -+ -+&leds { -+ act_led: act { -+ label = "led0"; -+ linux,default-trigger = "mmc0"; -+ gpios = <&gpio 47 0>; -+ }; -+}; -+ -+&mmc { -+ status = "okay"; -+ bus-width = <4>; -+}; -+ -+&fb { -+ status = "okay"; -+}; -+ -+&audio { -+ status = "okay"; -+}; -+ -+/ { -+ __overrides__ { -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; -+ act_led_trigger = <&act_led>,"linux,default-trigger"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708.dtsi -@@ -0,0 +1,19 @@ -+/include/ "bcm2708_common.dtsi" -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ model = "BCM2708"; -+ -+ chosen { -+ /* No padding required - the boot loader can do that. */ -+ bootargs = ""; -+ }; -+ -+ soc { -+ ranges = <0x7e000000 0x20000000 0x01000000>; -+ -+ arm-pmu { -+ compatible = "arm,arm1176-pmu"; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2708_common.dtsi -@@ -0,0 +1,230 @@ -+/include/ "skeleton.dtsi" -+ -+/ { -+ interrupt-parent = <&intc>; -+ -+ /* Onboard audio */ -+ audio: audio { -+ compatible = "brcm,bcm2835-audio"; -+ brcm,pwm-channels = <8>; -+ status = "disabled"; -+ }; -+ -+ soc: soc { -+ compatible = "simple-bus"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ dma: dma@7e007000 { -+ compatible = "brcm,bcm2835-dma"; -+ reg = <0x7e007000 0xf00>; -+ interrupts = <1 16>, -+ <1 17>, -+ <1 18>, -+ <1 19>, -+ <1 20>, -+ <1 21>, -+ <1 22>, -+ <1 23>, -+ <1 24>, -+ <1 25>, -+ <1 26>, -+ <1 27>, -+ <1 28>; -+ -+ #dma-cells = <1>; -+ brcm,dma-channel-mask = <0x7f35>; -+ }; -+ -+ intc: interrupt-controller { -+ compatible = "brcm,bcm2708-armctrl-ic"; -+ reg = <0x7e00b200 0x200>; -+ interrupt-controller; -+ #interrupt-cells = <2>; -+ }; -+ -+ watchdog: watchdog@7e100000 { -+ compatible = "brcm,bcm2835-pm-wdt"; -+ reg = <0x7e100000 0x28>; -+ status = "disabled"; -+ }; -+ -+ random: rng@7e104000 { -+ compatible = "brcm,bcm2835-rng"; -+ reg = <0x7e104000 0x10>; -+ status = "disabled"; -+ }; -+ -+ mailbox: mailbox@7e00b800 { -+ compatible = "brcm,bcm2708-vcio"; -+ reg = <0x7e00b880 0x40>; -+ interrupts = <0 1>; -+ }; -+ -+ gpio: gpio { -+ compatible = "brcm,bcm2835-gpio"; -+ reg = <0x7e200000 0xb4>; -+ interrupts = <2 17>, <2 18>; -+ -+ gpio-controller; -+ #gpio-cells = <2>; -+ -+ interrupt-controller; -+ #interrupt-cells = <2>; -+ }; -+ -+ mmc: mmc@7e300000 { -+ compatible = "brcm,bcm2835-mmc"; -+ reg = <0x7e300000 0x100>; -+ interrupts = <2 30>; -+ clocks = <&clk_mmc>; -+ dmas = <&dma 11>, -+ <&dma 11>; -+ dma-names = "tx", "rx"; -+ status = "disabled"; -+ }; -+ -+ uart0: uart@7e201000 { -+ compatible = "arm,pl011", "arm,primecell"; -+ reg = <0x7e201000 0x1000>; -+ interrupts = <2 25>; -+ clocks = <&clk_uart0 &clk_apb_p>; -+ clock-names = "uartclk","apb_pclk"; -+ arm,primecell-periphid = <0x00241011>; // For an explanation, see -+ // https://github.com/raspberrypi/linux/commit/13731d862cf5219216533a3b0de052cee4cc5038 -+ status = "disabled"; -+ }; -+ -+ i2s: i2s@7e203000 { -+ compatible = "brcm,bcm2708-i2s"; -+ reg = <0x7e203000 0x20>, -+ <0x7e101098 0x02>; -+ -+ //dmas = <&dma 2>, -+ // <&dma 3>; -+ dma-names = "tx", "rx"; -+ status = "disabled"; -+ }; -+ -+ spi0: spi@7e204000 { -+ compatible = "brcm,bcm2835-spi"; -+ reg = <0x7e204000 0x1000>; -+ interrupts = <2 22>; -+ clocks = <&clk_spi>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ /* the dma channels */ -+ dmas = <&dma 6>, <&dma 7>; -+ dma-names = "tx", "rx"; -+ /* the chipselects used - <0> means native GPIO -+ * add more gpios if necessary as <&gpio 6 1> -+ * (but do not forget to make them output!) -+ */ -+ cs-gpios = <0>, <0>; -+ }; -+ -+ i2c0: i2c@7e205000 { -+ compatible = "brcm,bcm2708-i2c"; -+ reg = <0x7e205000 0x1000>; -+ interrupts = <2 21>; -+ clocks = <&clk_i2c>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ }; -+ -+ uart1: uart@7e215040 { -+ compatible = "brcm,bcm2835-aux-uart", "ns16550"; -+ reg = <0x7e215040 0x40>; -+ interrupts = <1 29>; -+ clock-frequency = <500000000>; -+ reg-shift = <2>; -+ no-loopback-test; -+ status = "disabled"; -+ }; -+ -+ i2c1: i2c@7e804000 { -+ compatible = "brcm,bcm2708-i2c"; -+ reg = <0x7e804000 0x1000>; -+ interrupts = <2 21>; -+ clocks = <&clk_i2c>; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "disabled"; -+ }; -+ -+ usb: usb@7e980000 { -+ compatible = "brcm,bcm2708-usb"; -+ reg = <0x7e980000 0x10000>, -+ <0x7e006000 0x1000>; -+ interrupts = <2 0>, -+ <1 9>; -+ }; -+ -+ leds: leds { -+ compatible = "gpio-leds"; -+ }; -+ -+ fb: fb { -+ compatible = "brcm,bcm2708-fb"; -+ status = "disabled"; -+ }; -+ -+ vchiq: vchiq { -+ compatible = "brcm,bcm2835-vchiq"; -+ reg = <0x7e00b840 0xf>; -+ interrupts = <0 2>; -+ }; -+ -+ thermal: thermal { -+ compatible = "brcm,bcm2835-thermal"; -+ }; -+ }; -+ -+ clocks: clocks { -+ compatible = "simple-bus"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ clk_mmc: clock@0 { -+ compatible = "fixed-clock"; -+ reg = <0>; -+ #clock-cells = <0>; -+ clock-output-names = "mmc"; -+ clock-frequency = <250000000>; -+ }; -+ -+ clk_i2c: clock@1 { -+ compatible = "fixed-clock"; -+ reg = <1>; -+ #clock-cells = <0>; -+ clock-output-names = "i2c"; -+ clock-frequency = <250000000>; -+ }; -+ -+ clk_spi: clock@2 { -+ compatible = "fixed-clock"; -+ reg = <2>; -+ #clock-cells = <0>; -+ clock-output-names = "spi"; -+ clock-frequency = <250000000>; -+ }; -+ -+ clk_uart0: clock@3 { -+ compatible = "fixed-clock"; -+ reg = <3>; -+ #clock-cells = <0>; -+ clock-output-names = "uart0_pclk"; -+ clock-frequency = <3000000>; -+ }; -+ -+ clk_apb_p: clock@4 { -+ compatible = "fixed-clock"; -+ reg = <4>; -+ #clock-cells = <0>; -+ clock-output-names = "apb_pclk"; -+ clock-frequency = <126000000>; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts -@@ -0,0 +1,140 @@ -+/dts-v1/; -+ -+/include/ "bcm2709.dtsi" -+ -+/ { -+ compatible = "brcm,bcm2709"; -+ model = "Raspberry Pi 2 Model B"; -+ -+ aliases { -+ soc = &soc; -+ spi0 = &spi0; -+ i2c0 = &i2c0; -+ i2c1 = &i2c1; -+ i2s = &i2s; -+ gpio = &gpio; -+ intc = &intc; -+ leds = &leds; -+ audio = &audio; -+ sound = &sound; -+ uart0 = &uart0; -+ uart1 = &uart1; -+ clocks = &clocks; -+ }; -+ -+ sound: sound { -+ }; -+}; -+ -+&gpio { -+ spi0_pins: spi0_pins { -+ brcm,pins = <7 8 9 10 11>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+ -+ i2c0_pins: i2c0 { -+ brcm,pins = <0 1>; -+ brcm,function = <4>; -+ }; -+ -+ i2c1_pins: i2c1 { -+ brcm,pins = <2 3>; -+ brcm,function = <4>; -+ }; -+ -+ i2s_pins: i2s { -+ brcm,pins = <18 19 20 21>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+}; -+ -+&mmc { -+ status = "okay"; -+ bus-width = <4>; -+}; -+ -+&fb { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+&spi0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&spi0_pins>; -+ -+ spidev@0{ -+ compatible = "spidev"; -+ reg = <0>; /* CE0 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+ -+ spidev@1{ -+ compatible = "spidev"; -+ reg = <1>; /* CE1 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; -+ }; -+}; -+ -+&i2c0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c0_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2c1 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c1_pins>; -+ clock-frequency = <100000>; -+}; -+ -+&i2s { -+ #sound-dai-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2s_pins>; -+}; -+ -+&leds { -+ act_led: act { -+ label = "led0"; -+ linux,default-trigger = "mmc0"; -+ gpios = <&gpio 47 0>; -+ }; -+ -+ pwr_led: pwr { -+ label = "led1"; -+ linux,default-trigger = "input"; -+ gpios = <&gpio 35 0>; -+ }; -+}; -+ -+/ { -+ __overrides__ { -+ uart0 = <&uart0>,"status"; -+ uart0_clkrate = <&clk_uart0>,"clock-frequency:0"; -+ i2s = <&i2s>,"status"; -+ spi = <&spi0>,"status"; -+ i2c0 = <&i2c0>,"status"; -+ i2c1 = <&i2c1>,"status"; -+ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; -+ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; -+ -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; -+ act_led_trigger = <&act_led>,"linux,default-trigger"; -+ -+ pwr_led_gpio = <&pwr_led>,"gpios:4"; -+ pwr_led_activelow = <&pwr_led>,"gpios:8"; -+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; -+ -+ audio = <&audio>,"status"; -+ watchdog = <&watchdog>,"status"; -+ random = <&random>,"status"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/bcm2709.dtsi -@@ -0,0 +1,70 @@ -+/include/ "bcm2708_common.dtsi" -+ -+/ { -+ compatible = "brcm,bcm2709"; -+ model = "BCM2709"; -+ -+ chosen { -+ /* No padding required - the boot loader can do that. */ -+ bootargs = ""; -+ }; -+ -+ soc { -+ ranges = <0x7e000000 0x3f000000 0x01000000>; -+ -+ arm-pmu { -+ compatible = "arm,cortex-a7-pmu"; -+ interrupts = <3 9>; -+ }; -+ }; -+ -+ timer { -+ compatible = "arm,armv7-timer"; -+ clock-frequency = <19200000>; -+ interrupts = <3 0>, // PHYS_SECURE_PPI -+ <3 1>, // PHYS_NONSECURE_PPI -+ <3 3>, // VIRT_PPI -+ <3 2>; // HYP_PPI -+ always-on; -+ }; -+ -+ cpus: cpus { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ v7_cpu0: cpu@0 { -+ device_type = "cpu"; -+ compatible = "arm,cortex-a7"; -+ reg = <0xf00>; -+ clock-frequency = <800000000>; -+ }; -+ -+ v7_cpu1: cpu@1 { -+ device_type = "cpu"; -+ compatible = "arm,cortex-a7"; -+ reg = <0xf01>; -+ clock-frequency = <800000000>; -+ }; -+ -+ v7_cpu2: cpu@2 { -+ device_type = "cpu"; -+ compatible = "arm,cortex-a7"; -+ reg = <0xf02>; -+ clock-frequency = <800000000>; -+ }; -+ -+ v7_cpu3: cpu@3 { -+ device_type = "cpu"; -+ compatible = "arm,cortex-a7"; -+ reg = <0xf03>; -+ clock-frequency = <800000000>; -+ }; -+ }; -+ -+ __overrides__ { -+ arm_freq = <&v7_cpu0>, "clock-frequency:0", -+ <&v7_cpu1>, "clock-frequency:0", -+ <&v7_cpu2>, "clock-frequency:0", -+ <&v7_cpu3>, "clock-frequency:0"; -+ }; -+}; ---- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts -+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts -@@ -4,27 +4,40 @@ - / { - compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; - model = "Raspberry Pi Model B+"; -- -- leds { -- act { -- gpios = <&gpio 47 0>; -- }; -- -- pwr { -- label = "PWR"; -- gpios = <&gpio 35 0>; -- default-state = "keep"; -- linux,default-trigger = "default-on"; -- }; -- }; - }; - - &gpio { -- pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>; -- -- /* I2S interface */ -- i2s_alt0: i2s_alt0 { -+ i2s_pins: i2s { - brcm,pins = <18 19 20 21>; - brcm,function = <4>; /* alt0 */ - }; - }; -+ -+&i2s { -+ #sound-dai-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2s_pins>; -+}; -+ -+&act_led { -+ gpios = <&gpio 47 0>; -+}; -+ -+&leds { -+ pwr_led: pwr { -+ label = "led1"; -+ linux,default-trigger = "input"; -+ gpios = <&gpio 35 0>; -+ }; -+}; -+ -+/ { -+ __overrides__ { -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; -+ -+ pwr_led_gpio = <&pwr_led>,"gpios:4"; -+ pwr_led_activelow = <&pwr_led>,"gpios:8"; -+ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; -+ }; -+}; ---- a/arch/arm/boot/dts/bcm2835-rpi-b.dts -+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts -@@ -5,19 +5,28 @@ - compatible = "raspberrypi,model-b", "brcm,bcm2835"; - model = "Raspberry Pi Model B"; - -- leds { -- act { -- gpios = <&gpio 16 1>; -- }; -- }; - }; - - &gpio { -- pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>; -- -- /* I2S interface */ -- i2s_alt2: i2s_alt2 { -+ i2s_pins: i2s { - brcm,pins = <28 29 30 31>; -- brcm,function = <6>; /* alt2 */ -+ brcm,function = <4>; /* alt0 */ -+ }; -+}; -+ -+&i2s { -+ #sound-dai-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2s_pins>; -+}; -+ -+&act_led { -+ gpios = <&gpio 16 1>; -+}; -+ -+/ { -+ __overrides__ { -+ act_led_gpio = <&act_led>,"gpios:4"; -+ act_led_activelow = <&act_led>,"gpios:8"; - }; - }; ---- a/arch/arm/boot/dts/bcm2835-rpi.dtsi -+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi -@@ -1,51 +1,112 @@ - /include/ "bcm2835.dtsi" - - / { -+ /* This is left here in case u-boot needs it */ - memory { - reg = <0 0x10000000>; - }; - -- leds { -+ aliases { -+ soc = &soc; -+ spi0 = &spi0; -+ i2c0 = &i2c0; -+ i2c1 = &i2c1; -+ i2s = &i2s; -+ gpio = &gpio; -+ intc = &intc; -+ leds = &leds; -+ sound = &sound; -+ }; -+ -+ leds: leds { - compatible = "gpio-leds"; - -- act { -- label = "ACT"; -- default-state = "keep"; -- linux,default-trigger = "heartbeat"; -+ act_led: act { -+ label = "led0"; -+ linux,default-trigger = "mmc0"; - }; - }; -+ -+ /* Onboard audio */ -+ audio: audio { -+ compatible = "brcm,bcm2835-audio"; -+ brcm,pwm-channels = <8>; -+ status = "disabled"; -+ }; -+ -+ /* External sound card */ -+ sound: sound { -+ }; - }; - - &gpio { -- pinctrl-names = "default"; -+ spi0_pins: spi0_pins { -+ brcm,pins = <7 8 9 10 11>; -+ brcm,function = <4>; /* alt0 */ -+ }; - -- gpioout: gpioout { -- brcm,pins = <6>; -- brcm,function = <1>; /* GPIO out */ -+ i2c0_pins: i2c0 { -+ brcm,pins = <0 1>; -+ brcm,function = <4>; - }; - -- alt0: alt0 { -- brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>; -- brcm,function = <4>; /* alt0 */ -+ i2c1_pins: i2c1 { -+ brcm,pins = <2 3>; -+ brcm,function = <4>; -+ }; -+}; -+ -+&spi0 { -+ pinctrl-names = "default"; -+ pinctrl-0 = <&spi0_pins>; -+ -+ spidev@0{ -+ compatible = "spidev"; -+ reg = <0>; /* CE0 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; - }; - -- alt3: alt3 { -- brcm,pins = <48 49 50 51 52 53>; -- brcm,function = <7>; /* alt3 */ -+ spidev@1{ -+ compatible = "spidev"; -+ reg = <1>; /* CE1 */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ spi-max-frequency = <500000>; - }; - }; - - &i2c0 { -- status = "okay"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c0_pins>; - clock-frequency = <100000>; - }; - - &i2c1 { -- status = "okay"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&i2c1_pins>; - clock-frequency = <100000>; - }; - --&sdhci { -+&mmc { - status = "okay"; - bus-width = <4>; - }; -+ -+&fb { -+ status = "okay"; -+}; -+ -+/ { -+ __overrides__ { -+ i2s = <&i2s>,"status"; -+ spi = <&spi0>,"status"; -+ i2c0 = <&i2c0>,"status"; -+ i2c1 = <&i2c1>,"status"; -+ i2c0_baudrate = <&i2c0>,"clock-frequency:0"; -+ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; -+ act_led_trigger = <&act_led>,"linux,default-trigger"; -+ audio = <&audio>,"status"; -+ }; -+}; ---- a/arch/arm/boot/dts/bcm2835.dtsi -+++ b/arch/arm/boot/dts/bcm2835.dtsi -@@ -6,14 +6,15 @@ - interrupt-parent = <&intc>; - - chosen { -- bootargs = "earlyprintk console=ttyAMA0"; -+ bootargs = ""; - }; - -- soc { -+ soc: soc { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x7e000000 0x20000000 0x02000000>; -+ dma-ranges = <0x40000000 0x00000000 0x20000000>; - - timer@7e003000 { - compatible = "brcm,bcm2835-system-timer"; -@@ -50,16 +51,22 @@ - #interrupt-cells = <2>; - }; - -- watchdog@7e100000 { -+ watchdog: watchdog@7e100000 { - compatible = "brcm,bcm2835-pm-wdt"; - reg = <0x7e100000 0x28>; - }; - -- rng@7e104000 { -+ random: rng@7e104000 { - compatible = "brcm,bcm2835-rng"; - reg = <0x7e104000 0x10>; - }; - -+ mailbox: mailbox@7e00b800 { -+ compatible = "brcm,bcm2708-vcio"; -+ reg = <0x7e00b880 0x40>; -+ interrupts = <0 1>; -+ }; -+ - gpio: gpio@7e200000 { - compatible = "brcm,bcm2835-gpio"; - reg = <0x7e200000 0xb4>; -@@ -83,7 +90,7 @@ - #interrupt-cells = <2>; - }; - -- uart@7e201000 { -+ uart0: uart@7e201000 { - compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; - reg = <0x7e201000 0x1000>; - interrupts = <2 25>; -@@ -102,7 +109,7 @@ - status = "disabled"; - }; - -- spi: spi@7e204000 { -+ spi0: spi@7e204000 { - compatible = "brcm,bcm2835-spi"; - reg = <0x7e204000 0x1000>; - interrupts = <2 22>; -@@ -122,11 +129,14 @@ - status = "disabled"; - }; - -- sdhci: sdhci@7e300000 { -- compatible = "brcm,bcm2835-sdhci"; -+ mmc: mmc@7e300000 { -+ compatible = "brcm,bcm2835-mmc"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clk_mmc>; -+ dmas = <&dma 11>, -+ <&dma 11>; -+ dma-names = "tx", "rx"; - status = "disabled"; - }; - -@@ -140,7 +150,7 @@ - status = "disabled"; - }; - -- usb@7e980000 { -+ usb: usb@7e980000 { - compatible = "brcm,bcm2835-usb"; - reg = <0x7e980000 0x10000>; - interrupts = <1 9>; -@@ -149,6 +159,21 @@ - arm-pmu { - compatible = "arm,arm1176-pmu"; - }; -+ -+ fb: fb { -+ compatible = "brcm,bcm2708-fb"; -+ status = "disabled"; -+ }; -+ -+ vchiq: vchiq { -+ compatible = "brcm,bcm2835-vchiq"; -+ reg = <0x7e00b840 0xf>; -+ interrupts = <0 2>; -+ }; -+ -+ thermal: thermal { -+ compatible = "brcm,bcm2835-thermal"; -+ }; - }; - - clocks { -@@ -161,7 +186,7 @@ - reg = <0>; - #clock-cells = <0>; - clock-output-names = "mmc"; -- clock-frequency = <100000000>; -+ clock-frequency = <250000000>; - }; - - clk_i2c: clock@1 { ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/Makefile -@@ -0,0 +1,57 @@ -+ifeq ($(CONFIG_OF),y) -+ -+# Overlays for the Raspberry Pi platform -+ -+ifeq ($(CONFIG_BCM2708_DT),y) -+ RPI_DT_OVERLAYS=y -+endif -+ifeq ($(CONFIG_BCM2709_DT),y) -+ RPI_DT_OVERLAYS=y -+endif -+ifeq ($(CONFIG_ARCH_BCM2835),y) -+ RPI_DT_OVERLAYS=y -+endif -+ -+dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hifiberry-amp-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dac-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hifiberry-dacplus-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hifiberry-digi-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hy28a-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += hy28b-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += i2c-rtc-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += i2s-mmap-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dac-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += iqaudio-dacplus-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += lirc-rpi-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += mcp2515-can0-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += mmc-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += mz61581-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += piscreen-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += pitft28-resistive-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += pps-gpio-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += rpi-dac-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += rpi-display-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += rpi-proto-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += sdhost-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += spi-bcm2708-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += spi-bcm2835-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += tinylcd35-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-overlay.dtb -+dtb-$(RPI_DT_OVERLAYS) += w1-gpio-pullup-overlay.dtb -+ -+targets += dtbs dtbs_install -+targets += $(dtb-y) -+ -+endif -+ -+always := $(dtb-y) -+clean-files := *.dtb -+ -+# Enable fixups to support overlays on BCM2708 platforms -+ifeq ($(RPI_DT_OVERLAYS),y) -+ DTC_FLAGS ?= -@ -+endif ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/README -@@ -0,0 +1,493 @@ -+Introduction -+============ -+ -+This directory contains Device Tree overlays. Device Tree makes it possible -+to support many hardware configurations with a single kernel and without the -+need to explicitly load or blacklist kernel modules. Note that this isn't a -+"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices -+are still configured by the board support code, but the intention is to -+eventually reach that goal. -+ -+On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By -+default, the Raspberry Pi kernel boots with device tree enabled. You can -+completely disable DT usage (for now) by adding: -+ -+ device_tree= -+ -+to your config.txt, which should cause your Pi to revert to the old way of -+doing things after a reboot. -+ -+In /boot you will find a .dtb for each base platform. This describes the -+hardware that is part of the Raspberry Pi board. The loader (start.elf and its -+siblings) selects the .dtb file appropriate for the platform by name, and reads -+it into memory. At this point, all of the optional interfaces (i2c, i2s, spi) -+are disabled, but they can be enabled using Device Tree parameters: -+ -+ dtparam=i2c=on,i2s=on,spi=on -+ -+However, this shouldn't be necessary in many use cases because loading an -+overlay that requires one of those interfaces will cause it to be enabled -+automatically, and it is advisable to only enable interfaces if they are -+needed. -+ -+Configuring additional, optional hardware is done using Device Tree overlays -+(see below). -+ -+raspi-config -+============ -+ -+The Advanced Options section of the raspi-config utility can enable and disable -+Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it -+is possible to both enable an interface and blacklist the driver, if for some -+reason you should want to defer the loading. -+ -+Modules -+======= -+ -+As well as describing the hardware, Device Tree also gives enough information -+to allow suitable driver modules to be located and loaded, with the corollary -+that unneeded modules are not loaded. As a result it should be possible to -+remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can -+have its contents deleted (or commented out). -+ -+Using Overlays -+============== -+ -+Overlays are loaded using the "dtoverlay" directive. As an example, consider the -+popular lirc-rpi module, the Linux Infrared Remote Control driver. In the -+pre-DT world this would be loaded from /etc/modules, with an explicit -+"modprobe lirc-rpi" command, or programmatically by lircd. With DT enabled, -+this becomes a line in config.txt: -+ -+ dtoverlay=lirc-rpi -+ -+This causes the file /boot/overlays/lirc-rpi-overlay.dtb to be loaded. By -+default it will use GPIOs 17 (out) and 18 (in), but this can be modified using -+DT parameters: -+ -+ dtoverlay=lirc-rpi,gpio_out_pin=17,gpio_in_pin=13 -+ -+Parameters always have default values, although in some cases (e.g. "w1-gpio") -+it is necessary to provided multiple overlays in order to get the desired -+behaviour. See the list of overlays below for a description of the parameters and their defaults. -+ -+The Overlay and Parameter Reference -+=================================== -+ -+Name: <The base DTB> -+Info: Configures the base Raspberry Pi hardware -+Load: <loaded automatically> -+Params: -+ audio Set to "on" to disable the onboard ALSA audio -+ interface (default "off") -+ -+ i2c_arm Set to "on" to enable the ARM's i2c interface -+ (default "off") -+ -+ i2c_vc Set to "on" to enable the i2c interface -+ usually reserved for the VideoCore processor -+ (default "off") -+ -+ i2c An alias for i2c_arm -+ -+ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface -+ (default "100000") -+ -+ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface -+ (default "100000") -+ -+ i2c_baudrate An alias for i2c_arm_baudrate -+ -+ i2s Set to "on" to enable the i2s interface -+ (default "off") -+ -+ spi Set to "on" to enable the spi interfaces -+ (default "off") -+ -+ random Set to "on" to enable the hardware random -+ number generator (default "off") -+ -+ uart0 Set to "off" to disable uart0 (default "on") -+ -+ watchdog Set to "on" to enable the hardware watchdog -+ (default "off") -+ -+ act_led_trigger Choose which activity the LED tracks. -+ Use "heartbeat" for a nice load indicator. -+ (default "mmc") -+ -+ act_led_activelow Set to "on" to invert the sense of the LED -+ (default "off") -+ -+ act_led_gpio Set which GPIO to use for the activity LED -+ (in case you want to connect it to an external -+ device) -+ (default "16" on a non-Plus board, "47" on a -+ Plus or Pi 2) -+ -+ pwr_led_trigger -+ pwr_led_activelow -+ pwr_led_gpio -+ As for act_led_*, but using the PWR LED. -+ Not available on Model A/B boards. -+ -+ N.B. It is recommended to only enable those interfaces that are needed. -+ Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc -+ interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) -+ Note also that i2c, i2c_arm and i2c_vc are aliases for the physical -+ interfaces i2c0 and i2c1. Use of the numeric variants is still possible -+ but deprecated because the ARM/VC assignments differ between board -+ revisions. The same board-specific mapping applies to i2c_baudrate, -+ and the other i2c baudrate parameters. -+ -+ -+Name: ads7846 -+Info: ADS7846 Touch controller -+Load: dtoverlay=ads7846,<param>=<val> -+Params: cs SPI bus Chip Select (default 1) -+ speed SPI bus speed (default 2Mhz, max 3.25MHz) -+ penirq GPIO used for PENIRQ. REQUIRED -+ penirq_pull Set GPIO pull (default 0=none, 2=pullup) -+ swapxy Swap x and y axis -+ xmin Minimum value on the X axis (default 0) -+ ymin Minimum value on the Y axis (default 0) -+ xmax Maximum value on the X axis (default 4095) -+ ymax Maximum value on the Y axis (default 4095) -+ pmin Minimum reported pressure value (default 0) -+ pmax Maximum reported pressure value (default 65535) -+ xohms Touchpanel sensitivity (X-plate resistance) -+ (default 400) -+ -+ penirq is required and usually xohms (60-100) has to be set as well. -+ Apart from that, pmax (255) and swapxy are also common. -+ The rest of the calibration can be done with xinput-calibrator. -+ See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian -+ Device Tree binding document: -+ www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt -+ -+ -+Name: bmp085_i2c-sensor -+Info: Configures the BMP085/BMP180 digital barometric pressure and temperature -+ sensors from Bosch Sensortec -+Load: dtoverlay=bmp085_i2c-sensor -+Params: <None> -+ -+ -+[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ] -+ -+ -+Name: enc28j60 -+Info: Overlay for the Microchip ENC28J60 Ethernet Controller (SPI) -+Load: dtoverlay=enc28j60,<param>=<val> -+Params: int_pin GPIO used for INT (default 25) -+ -+ speed SPI bus speed (default 12000000) -+ -+ -+Name: hifiberry-amp -+Info: Configures the HifiBerry Amp and Amp+ audio cards -+Load: dtoverlay=hifiberry-amp -+Params: <None> -+ -+ -+Name: hifiberry-dac -+Info: Configures the HifiBerry DAC audio card -+Load: dtoverlay=hifiberry-dac -+Params: <None> -+ -+ -+Name: hifiberry-dacplus -+Info: Configures the HifiBerry DAC+ audio card -+Load: dtoverlay=hifiberry-dacplus -+Params: <None> -+ -+ -+Name: hifiberry-digi -+Info: Configures the HifiBerry Digi audio card -+Load: dtoverlay=hifiberry-digi -+Params: <None> -+ -+ -+Name: hy28a -+Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics -+ Default values match Texy's display shield -+Load: dtoverlay=hy28a,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ xohms Touchpanel sensitivity (X-plate resistance) -+ -+ resetgpio GPIO used to reset controller -+ -+ ledgpio GPIO used to control backlight -+ -+ -+Name: hy28b -+Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics -+ Default values match Texy's display shield -+Load: dtoverlay=hy28b,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ xohms Touchpanel sensitivity (X-plate resistance) -+ -+ resetgpio GPIO used to reset controller -+ -+ ledgpio GPIO used to control backlight -+ -+ -+Name: i2c-rtc -+Info: Adds support for a number of I2C Real Time Clock devices -+Load: dtoverlay=i2c-rtc,<param> -+Params: ds1307 Select the DS1307 device -+ -+ ds3231 Select the DS3231 device -+ -+ pcf2127 Select the PCF2127 device -+ -+ pcf8523 Select the PCF8523 device -+ -+ pcf8563 Select the PCF8563 device -+ -+ -+Name: iqaudio-dac -+Info: Configures the IQaudio DAC audio card -+Load: dtoverlay=iqaudio-dac -+Params: <None> -+ -+ -+Name: iqaudio-dacplus -+Info: Configures the IQaudio DAC+ audio card -+Load: dtoverlay=iqaudio-dacplus -+Params: <None> -+ -+ -+Name: lirc-rpi -+Info: Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi) -+ Consult the module documentation for more details. -+Load: dtoverlay=lirc-rpi,<param>=<val>,... -+Params: gpio_out_pin GPIO for output (default "17") -+ -+ gpio_in_pin GPIO for input (default "18") -+ -+ gpio_in_pull Pull up/down/off on the input pin -+ (default "down") -+ -+ sense Override the IR receive auto-detection logic: -+ "1" = force active high -+ "0" = force active low -+ "-1" = use auto-detection -+ (default "-1") -+ -+ softcarrier Turn the software carrier "on" or "off" -+ (default "on") -+ -+ invert "on" = invert the output pin (default "off") -+ -+ debug "on" = enable additional debug messages -+ (default "off") -+ -+ -+Name: mcp2515-can0 -+Info: Configures the MCP2515 CAN controller -+Load: dtoverlay=mcp2515-can0,<param>=<val> -+Params: oscillator Clock frequency for the CAN controller (Hz) -+ -+ spimaxfrequency Maximum SPI frequence (Hz) -+ -+ interrupt GPIO for interrupt signal -+ -+ -+Name: mmc -+Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock -+Load: dtoverlay=mmc,<param>=<val> -+Params: overclock_50 Clock (in MHz) to use when the MMC framework -+ requests 50MHz -+ force_pio Disable DMA support -+ -+ -+Name: mz61581 -+Info: MZ61581 display by Tontec -+Load: dtoverlay=mz61581,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ xohms Touchpanel sensitivity (X-plate resistance) -+ -+ -+[ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ] -+ -+ -+[ The pcf8523-rtc overlay has been deleted. See i2c-rtc. ] -+ -+ -+[ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ] -+ -+ -+Name: piscreen -+Info: PiScreen display by OzzMaker.com -+Load: dtoverlay=piscreen,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ xohms Touchpanel sensitivity (X-plate resistance) -+ -+ -+Name: pitft28-resistive -+Info: Adafruit PiTFT 2.8" resistive touch screen -+Load: dtoverlay=pitft28-resistive,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ -+Name: pps-gpio -+Info: Configures the pps-gpio (pulse-per-second time signal via GPIO). -+Load: dtoverlay=pps-gpio,<param>=<val> -+Params: gpiopin Input GPIO (default "18") -+ -+ -+Name: rpi-dac -+Info: Configures the RPi DAC audio card -+Load: dtoverlay=rpi-dac -+Params: <None> -+ -+ -+Name: rpi-display -+Info: RPi-Display - 2.8" Touch Display by Watterott -+Load: dtoverlay=rpi-display,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ xohms Touchpanel sensitivity (X-plate resistance) -+ -+ -+Name: rpi-proto -+Info: Configures the RPi Proto audio card -+Load: dtoverlay=rpi-proto -+Params: <None> -+ -+ -+Name: sdhost -+Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock -+Load: dtoverlay=sdhost,<param>=<val> -+Params: overclock_50 Clock (in MHz) to use when the MMC framework -+ requests 50MHz -+ force_pio Disable DMA support -+ -+ -+Name: spi-bcm2708 -+Info: Selects the bcm2708-spi SPI driver -+Load: dtoverlay=spi-bcm2708 -+Params: <None> -+ -+ -+Name: spi-bcm2835 -+Info: Selects the bcm2835-spi SPI driver -+Load: dtoverlay=spi-bcm2835 -+Params: <None> -+ -+ -+Name: tinylcd35 -+Info: 3.5" Color TFT Display by www.tinylcd.com -+ Options: Touch, RTC, keypad -+Load: dtoverlay=tinylcd35,<param>=<val> -+Params: speed Display SPI bus speed -+ -+ rotate Display rotation {0,90,180,270} -+ -+ fps Delay between frame updates -+ -+ debug Debug output level {0-7} -+ -+ touch Enable touch panel -+ -+ touchgpio Touch controller IRQ GPIO -+ -+ xohms Touchpanel: Resistance of X-plate in ohms -+ -+ rtc-pcf PCF8563 Real Time Clock -+ -+ rtc-ds DS1307 Real Time Clock -+ -+ keypad Enable keypad -+ -+ Examples: -+ Display with touchpanel, PCF8563 RTC and keypad: -+ dtoverlay=tinylcd35,touch,rtc-pcf,keypad -+ Old touch display: -+ dtoverlay=tinylcd35,touch,touchgpio=3 -+ -+ -+Name: w1-gpio -+Info: Configures the w1-gpio Onewire interface module. -+ Use this overlay if you *don't* need a GPIO to drive an external pullup. -+Load: dtoverlay=w1-gpio,<param>=<val> -+Params: gpiopin GPIO for I/O (default "4") -+ -+ pullup Non-zero, "on", or "y" to enable the parasitic -+ power (2-wire, power-on-data) feature -+ -+ -+Name: w1-gpio-pullup -+Info: Configures the w1-gpio Onewire interface module. -+ Use this overlay if you *do* need a GPIO to drive an external pullup. -+Load: dtoverlay=w1-gpio-pullup,<param>=<val>,... -+Params: gpiopin GPIO for I/O (default "4") -+ -+ pullup Non-zero, "on", or "y" to enable the parasitic -+ power (2-wire, power-on-data) feature -+ -+ extpullup GPIO for external pullup (default "5") -+ -+ -+Troubleshooting -+=============== -+ -+If you are experiencing problems that you think are DT-related, enable DT -+diagnostic output by adding this to /boot/config.txt: -+ -+ dtdebug=on -+ -+and rebooting. Then run: -+ -+ sudo vcdbg log msg -+ -+and look for relevant messages. -+ -+Further reading -+=============== -+ -+This is only meant to be a quick introduction to the subject of Device Tree on -+Raspberry Pi. There is a more complete explanation here: -+ -+http://www.raspberrypi.org/documentation/configuration/device-tree.md ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/ads7846-overlay.dts -@@ -0,0 +1,83 @@ -+/* -+ * Generic Device Tree overlay for the ADS7846 touch controller -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ ads7846_pins: ads7846_pins { -+ brcm,pins = <255>; /* illegal default value */ -+ brcm,function = <0>; /* in */ -+ brcm,pull = <0>; /* none */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ ads7846: ads7846@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&ads7846_pins>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <255 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 255 0>; -+ -+ /* driver defaults */ -+ ti,x-min = /bits/ 16 <0>; -+ ti,y-min = /bits/ 16 <0>; -+ ti,x-max = /bits/ 16 <0x0FFF>; -+ ti,y-max = /bits/ 16 <0x0FFF>; -+ ti,pressure-min = /bits/ 16 <0>; -+ ti,pressure-max = /bits/ 16 <0xFFFF>; -+ ti,x-plate-ohms = /bits/ 16 <400>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ cs = <&ads7846>,"reg:0"; -+ speed = <&ads7846>,"spi-max-frequency:0"; -+ penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */ -+ <&ads7846>,"interrupts:0", -+ <&ads7846>,"pendown-gpio:4"; -+ penirq_pull = <&ads7846_pins>,"brcm,pull:0"; -+ swapxy = <&ads7846>,"ti,swap-xy?"; -+ xmin = <&ads7846>,"ti,x-min;0"; -+ ymin = <&ads7846>,"ti,y-min;0"; -+ xmax = <&ads7846>,"ti,x-max;0"; -+ ymax = <&ads7846>,"ti,y-max;0"; -+ pmin = <&ads7846>,"ti,pressure-min;0"; -+ pmax = <&ads7846>,"ti,pressure-max;0"; -+ xohms = <&ads7846>,"ti,x-plate-ohms;0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/bmp085_i2c-sensor-overlay.dts -@@ -0,0 +1,23 @@ -+// Definitions for BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ bmp085@77 { -+ compatible = "bosch,bmp085"; -+ reg = <0x77>; -+ default-oversampling = <3>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/dht11-overlay.dts -@@ -0,0 +1,39 @@ -+/* -+ * Overlay for the DHT11/21/22 humidity/temperature sensor modules. -+ */ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ -+ dht11: dht11@0 { -+ compatible = "dht11"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&dht11_pins>; -+ gpios = <&gpio 4 0>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ dht11_pins: dht11_pins { -+ brcm,pins = <4>; -+ brcm,function = <0>; // in -+ brcm,pull = <0>; // off -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ gpiopin = <&dht11_pins>,"brcm,pins:0", -+ <&dht11>,"gpios:4"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts -@@ -0,0 +1,50 @@ -+// Overlay for the Microchip ENC28J60 Ethernet Controller -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ eth1: enc28j60@0{ -+ compatible = "microchip,enc28j60"; -+ reg = <0>; /* CE0 */ -+ pinctrl-names = "default"; -+ pinctrl-0 = <ð1_pins>; -+ interrupt-parent = <&gpio>; -+ interrupts = <25 0x2>; /* falling edge */ -+ spi-max-frequency = <12000000>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ eth1_pins: eth1_pins { -+ brcm,pins = <25>; -+ brcm,function = <0>; /* in */ -+ brcm,pull = <0>; /* none */ -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ int_pin = <ð1>, "interrupts:0", -+ <ð1_pins>, "brcm,pins:0"; -+ speed = <ð1>, "spi-max-frequency:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for HiFiBerry Amp/Amp+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "hifiberry,hifiberry-amp"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ tas5713@1b { -+ #sound-dai-cells = <0>; -+ compatible = "ti,tas5713"; -+ reg = <0x1b>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts -@@ -0,0 +1,34 @@ -+// Definitions for HiFiBerry DAC -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "hifiberry,hifiberry-dac"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target-path = "/"; -+ __overlay__ { -+ pcm5102a-codec { -+ #sound-dai-cells = <0>; -+ compatible = "ti,pcm5102a"; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for HiFiBerry DAC+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "hifiberry,hifiberry-dacplus"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ pcm5122@4d { -+ #sound-dai-cells = <0>; -+ compatible = "ti,pcm5122"; -+ reg = <0x4d>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for HiFiBerry Digi -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "hifiberry,hifiberry-digi"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ wm8804@3b { -+ #sound-dai-cells = <0>; -+ compatible = "wlf,wm8804"; -+ reg = <0x3b>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hy28a-overlay.dts -@@ -0,0 +1,87 @@ -+/* -+ * Device Tree overlay for HY28A display -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ hy28a_pins: hy28a_pins { -+ brcm,pins = <17 25 18>; -+ brcm,function = <0 1 1>; /* in out out */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ hy28a: hy28a@0{ -+ compatible = "ilitek,ili9320"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&hy28a_pins>; -+ -+ spi-max-frequency = <32000000>; -+ spi-cpol; -+ spi-cpha; -+ rotate = <270>; -+ bgr; -+ fps = <50>; -+ buswidth = <8>; -+ startbyte = <0x70>; -+ reset-gpios = <&gpio 25 0>; -+ led-gpios = <&gpio 18 1>; -+ debug = <0>; -+ }; -+ -+ hy28a_ts: hy28a-ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <17 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 17 0>; -+ ti,x-plate-ohms = /bits/ 16 <100>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ speed = <&hy28a>,"spi-max-frequency:0"; -+ rotate = <&hy28a>,"rotate:0"; -+ fps = <&hy28a>,"fps:0"; -+ debug = <&hy28a>,"debug:0"; -+ xohms = <&hy28a_ts>,"ti,x-plate-ohms;0"; -+ resetgpio = <&hy28a>,"reset-gpios:4", -+ <&hy28a_pins>, "brcm,pins:1"; -+ ledgpio = <&hy28a>,"led-gpios:4", -+ <&hy28a_pins>, "brcm,pins:2"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/hy28b-overlay.dts -@@ -0,0 +1,142 @@ -+/* -+ * Device Tree overlay for HY28b display shield by Texy -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ hy28b_pins: hy28b_pins { -+ brcm,pins = <17 25 18>; -+ brcm,function = <0 1 1>; /* in out out */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ hy28b: hy28b@0{ -+ compatible = "ilitek,ili9325"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&hy28b_pins>; -+ -+ spi-max-frequency = <48000000>; -+ spi-cpol; -+ spi-cpha; -+ rotate = <270>; -+ bgr; -+ fps = <50>; -+ buswidth = <8>; -+ startbyte = <0x70>; -+ reset-gpios = <&gpio 25 0>; -+ led-gpios = <&gpio 18 1>; -+ -+ gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7"; -+ -+ init = <0x10000e7 0x0010 -+ 0x1000000 0x0001 -+ 0x1000001 0x0100 -+ 0x1000002 0x0700 -+ 0x1000003 0x1030 -+ 0x1000004 0x0000 -+ 0x1000008 0x0207 -+ 0x1000009 0x0000 -+ 0x100000a 0x0000 -+ 0x100000c 0x0001 -+ 0x100000d 0x0000 -+ 0x100000f 0x0000 -+ 0x1000010 0x0000 -+ 0x1000011 0x0007 -+ 0x1000012 0x0000 -+ 0x1000013 0x0000 -+ 0x2000032 -+ 0x1000010 0x1590 -+ 0x1000011 0x0227 -+ 0x2000032 -+ 0x1000012 0x009c -+ 0x2000032 -+ 0x1000013 0x1900 -+ 0x1000029 0x0023 -+ 0x100002b 0x000e -+ 0x2000032 -+ 0x1000020 0x0000 -+ 0x1000021 0x0000 -+ 0x2000032 -+ 0x1000050 0x0000 -+ 0x1000051 0x00ef -+ 0x1000052 0x0000 -+ 0x1000053 0x013f -+ 0x1000060 0xa700 -+ 0x1000061 0x0001 -+ 0x100006a 0x0000 -+ 0x1000080 0x0000 -+ 0x1000081 0x0000 -+ 0x1000082 0x0000 -+ 0x1000083 0x0000 -+ 0x1000084 0x0000 -+ 0x1000085 0x0000 -+ 0x1000090 0x0010 -+ 0x1000092 0x0000 -+ 0x1000093 0x0003 -+ 0x1000095 0x0110 -+ 0x1000097 0x0000 -+ 0x1000098 0x0000 -+ 0x1000007 0x0133 -+ 0x1000020 0x0000 -+ 0x1000021 0x0000 -+ 0x2000064>; -+ debug = <0>; -+ }; -+ -+ hy28b_ts: hy28b-ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <17 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 17 0>; -+ ti,x-plate-ohms = /bits/ 16 <100>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ speed = <&hy28b>,"spi-max-frequency:0"; -+ rotate = <&hy28b>,"rotate:0"; -+ fps = <&hy28b>,"fps:0"; -+ debug = <&hy28b>,"debug:0"; -+ xohms = <&hy28b_ts>,"ti,x-plate-ohms;0"; -+ resetgpio = <&hy28b>,"reset-gpios:4", -+ <&hy28b_pins>, "brcm,pins:1"; -+ ledgpio = <&hy28b>,"led-gpios:4", -+ <&hy28b_pins>, "brcm,pins:2"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts -@@ -0,0 +1,49 @@ -+// Definitions for several I2C based Real Time Clocks -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ ds1307: ds1307@68 { -+ compatible = "maxim,ds1307"; -+ reg = <0x68>; -+ status = "disable"; -+ }; -+ ds3231: ds3231@68 { -+ compatible = "maxim,ds3231"; -+ reg = <0x68>; -+ status = "disable"; -+ }; -+ pcf2127: pcf2127@51 { -+ compatible = "nxp,pcf2127"; -+ reg = <0x51>; -+ status = "disable"; -+ }; -+ pcf8523: pcf8523@68 { -+ compatible = "nxp,pcf8523"; -+ reg = <0x68>; -+ status = "disable"; -+ }; -+ pcf8563: pcf8563@51 { -+ compatible = "nxp,pcf8563"; -+ reg = <0x51>; -+ status = "disable"; -+ }; -+ }; -+ }; -+ __overrides__ { -+ ds1307 = <&ds1307>,"status"; -+ ds3231 = <&ds3231>,"status"; -+ pcf2127 = <&pcf2127>,"status"; -+ pcf8523 = <&pcf8523>,"status"; -+ pcf8563 = <&pcf8563>,"status"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/i2s-mmap-overlay.dts -@@ -0,0 +1,13 @@ -+/dts-v1/; -+/plugin/; -+ -+/{ -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&i2s>; -+ __overlay__ { -+ brcm,enable-mmap; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for IQaudIO DAC -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "iqaudio,iqaudio-dac"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ pcm5122@4c { -+ #sound-dai-cells = <0>; -+ compatible = "ti,pcm5122"; -+ reg = <0x4c>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for IQaudIO DAC+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "iqaudio,iqaudio-dac"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ pcm5122@4c { -+ #sound-dai-cells = <0>; -+ compatible = "ti,pcm5122"; -+ reg = <0x4c>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/lirc-rpi-overlay.dts -@@ -0,0 +1,57 @@ -+// Definitions for lirc-rpi module -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ lirc_rpi: lirc_rpi { -+ compatible = "rpi,lirc-rpi"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&lirc_pins>; -+ status = "okay"; -+ -+ // Override autodetection of IR receiver circuit -+ // (0 = active high, 1 = active low, -1 = no override ) -+ rpi,sense = <0xffffffff>; -+ -+ // Software carrier -+ // (0 = off, 1 = on) -+ rpi,softcarrier = <1>; -+ -+ // Invert output -+ // (0 = off, 1 = on) -+ rpi,invert = <0>; -+ -+ // Enable debugging messages -+ // (0 = off, 1 = on) -+ rpi,debug = <0>; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ lirc_pins: lirc_pins { -+ brcm,pins = <17 18>; -+ brcm,function = <1 0>; // out in -+ brcm,pull = <0 1>; // off down -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ gpio_out_pin = <&lirc_pins>,"brcm,pins:0"; -+ gpio_in_pin = <&lirc_pins>,"brcm,pins:4"; -+ gpio_in_pull = <&lirc_pins>,"brcm,pull:4"; -+ -+ sense = <&lirc_rpi>,"rpi,sense:0"; -+ softcarrier = <&lirc_rpi>,"rpi,softcarrier:0"; -+ invert = <&lirc_rpi>,"rpi,invert:0"; -+ debug = <&lirc_rpi>,"rpi,debug:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts -@@ -0,0 +1,69 @@ -+/* -+ * Device tree overlay for mcp251x/can0 on spi0.0 -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; -+ /* disable spi-dev for spi0.0 */ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ spidev@0{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ /* the interrupt pin of the can-controller */ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ can0_pins: can0_pins { -+ brcm,pins = <25>; -+ brcm,function = <0>; /* input */ -+ }; -+ }; -+ }; -+ -+ /* the clock/oscillator of the can-controller */ -+ fragment@2 { -+ target-path = "/clocks"; -+ __overlay__ { -+ /* external oscillator of mcp2515 on SPI0.0 */ -+ can0_osc: can0_osc { -+ compatible = "fixed-clock"; -+ #clock-cells = <0>; -+ clock-frequency = <16000000>; -+ }; -+ }; -+ }; -+ -+ /* the spi config of the can-controller itself binding everything together */ -+ fragment@3 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ can0: mcp2515@0 { -+ reg = <0>; -+ compatible = "microchip,mcp2515"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&can0_pins>; -+ spi-max-frequency = <10000000>; -+ interrupt-parent = <&gpio>; -+ interrupts = <25 0x2>; -+ clocks = <&can0_osc>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ oscillator = <&can0_osc>,"clock-frequency:0"; -+ spimaxfrequency = <&can0>,"spi-max-frequency:0"; -+ interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/mmc-overlay.dts -@@ -0,0 +1,19 @@ -+/dts-v1/; -+/plugin/; -+ -+/{ -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&mmc>; -+ -+ __overlay__ { -+ brcm,overclock-50 = <0>; -+ }; -+ }; -+ -+ __overrides__ { -+ overclock_50 = <&mmc>,"brcm,overclock-50:0"; -+ force_pio = <&mmc>,"brcm,force-pio?"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/mz61581-overlay.dts -@@ -0,0 +1,109 @@ -+/* -+ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ mz61581_pins: mz61581_pins { -+ brcm,pins = <4 15 18 25>; -+ brcm,function = <0 1 1 1>; /* in out out out */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ mz61581: mz61581@0{ -+ compatible = "samsung,s6d02a1"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&mz61581_pins>; -+ -+ spi-max-frequency = <128000000>; -+ spi-cpol; -+ spi-cpha; -+ -+ width = <320>; -+ height = <480>; -+ rotate = <270>; -+ bgr; -+ fps = <30>; -+ buswidth = <8>; -+ -+ reset-gpios = <&gpio 15 0>; -+ dc-gpios = <&gpio 25 0>; -+ led-gpios = <&gpio 18 0>; -+ -+ init = <0x10000b0 00 -+ 0x1000011 -+ 0x20000ff -+ 0x10000b3 0x02 0x00 0x00 0x00 -+ 0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43 -+ 0x10000c1 0x08 0x16 0x08 0x08 -+ 0x10000c4 0x11 0x07 0x03 0x03 -+ 0x10000c6 0x00 -+ 0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00 -+ 0x1000035 0x00 -+ 0x1000036 0xa0 -+ 0x100003a 0x55 -+ 0x1000044 0x00 0x01 -+ 0x10000d0 0x07 0x07 0x1d 0x03 -+ 0x10000d1 0x03 0x30 0x10 -+ 0x10000d2 0x03 0x14 0x04 -+ 0x1000029 -+ 0x100002c>; -+ -+ /* This is a workaround to make sure the init sequence slows down and doesn't fail */ -+ debug = <3>; -+ }; -+ -+ mz61581_ts: mz61581_ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <4 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 4 0>; -+ -+ ti,x-plate-ohms = /bits/ 16 <60>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ speed = <&mz61581>, "spi-max-frequency:0"; -+ rotate = <&mz61581>, "rotate:0"; -+ fps = <&mz61581>, "fps:0"; -+ debug = <&mz61581>, "debug:0"; -+ xohms = <&mz61581_ts>,"ti,x-plate-ohms;0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/piscreen-overlay.dts -@@ -0,0 +1,96 @@ -+/* -+ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ piscreen_pins: piscreen_pins { -+ brcm,pins = <17 25 24 22>; -+ brcm,function = <0 1 1 1>; /* in out out out */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ piscreen: piscreen@0{ -+ compatible = "ilitek,ili9486"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&piscreen_pins>; -+ -+ spi-max-frequency = <24000000>; -+ rotate = <270>; -+ bgr; -+ fps = <30>; -+ buswidth = <8>; -+ regwidth = <16>; -+ reset-gpios = <&gpio 25 0>; -+ dc-gpios = <&gpio 24 0>; -+ led-gpios = <&gpio 22 1>; -+ debug = <0>; -+ -+ init = <0x10000b0 0x00 -+ 0x1000011 -+ 0x20000ff -+ 0x100003a 0x55 -+ 0x1000036 0x28 -+ 0x10000c2 0x44 -+ 0x10000c5 0x00 0x00 0x00 0x00 -+ 0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00 -+ 0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 -+ 0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 -+ 0x1000011 -+ 0x1000029>; -+ }; -+ -+ piscreen_ts: piscreen-ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <17 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 17 0>; -+ ti,swap-xy; -+ ti,x-plate-ohms = /bits/ 16 <100>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ speed = <&piscreen>,"spi-max-frequency:0"; -+ rotate = <&piscreen>,"rotate:0"; -+ fps = <&piscreen>,"fps:0"; -+ debug = <&piscreen>,"debug:0"; -+ xohms = <&piscreen_ts>,"ti,x-plate-ohms;0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts -@@ -0,0 +1,115 @@ -+/* -+ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ pitft_pins: pitft_pins { -+ brcm,pins = <24 25>; -+ brcm,function = <0 1>; /* in out */ -+ brcm,pull = <2 0>; /* pullup none */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ pitft: pitft@0{ -+ compatible = "ilitek,ili9340"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&pitft_pins>; -+ -+ spi-max-frequency = <32000000>; -+ rotate = <90>; -+ fps = <25>; -+ bgr; -+ buswidth = <8>; -+ dc-gpios = <&gpio 25 0>; -+ debug = <0>; -+ }; -+ -+ pitft_ts@1 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ compatible = "st,stmpe610"; -+ reg = <1>; -+ -+ spi-max-frequency = <500000>; -+ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */ -+ interrupts = <24 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ interrupt-controller; -+ -+ stmpe_touchscreen { -+ compatible = "st,stmpe-ts"; -+ st,sample-time = <4>; -+ st,mod-12b = <1>; -+ st,ref-sel = <0>; -+ st,adc-freq = <2>; -+ st,ave-ctrl = <3>; -+ st,touch-det-delay = <4>; -+ st,settling = <2>; -+ st,fraction-z = <7>; -+ st,i-drive = <0>; -+ }; -+ -+ stmpe_gpio: stmpe_gpio { -+ #gpio-cells = <2>; -+ compatible = "st,stmpe-gpio"; -+ /* -+ * only GPIO2 is wired/available -+ * and it is wired to the backlight -+ */ -+ st,norequest-mask = <0x7b>; -+ }; -+ }; -+ }; -+ }; -+ -+ fragment@3 { -+ target-path = "/soc"; -+ __overlay__ { -+ backlight { -+ compatible = "gpio-backlight"; -+ gpios = <&stmpe_gpio 2 0>; -+ default-on; -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ speed = <&pitft>,"spi-max-frequency:0"; -+ rotate = <&pitft>,"rotate:0"; -+ fps = <&pitft>,"fps:0"; -+ debug = <&pitft>,"debug:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts -@@ -0,0 +1,34 @@ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ pps: pps { -+ compatible = "pps-gpio"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&pps_pins>; -+ gpios = <&gpio 18 0>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ pps_pins: pps_pins { -+ brcm,pins = <18>; -+ brcm,function = <0>; // in -+ brcm,pull = <0>; // off -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ gpiopin = <&pps>,"gpios:4", -+ <&pps_pins>,"brcm,pins:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts -@@ -0,0 +1,34 @@ -+// Definitions for RPi DAC -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "rpi,rpi-dac"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target-path = "/"; -+ __overlay__ { -+ pcm1794a-codec { -+ #sound-dai-cells = <0>; -+ compatible = "ti,pcm1794a"; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts -@@ -0,0 +1,82 @@ -+/* -+ * Device Tree overlay for rpi-display by Watterott -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ rpi_display_pins: rpi_display_pins { -+ brcm,pins = <18 23 24 25>; -+ brcm,function = <1 1 1 0>; /* out out out in */ -+ brcm,pull = <0 0 0 2>; /* - - - up */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ rpidisplay: rpi-display@0{ -+ compatible = "ilitek,ili9341"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&rpi_display_pins>; -+ -+ spi-max-frequency = <32000000>; -+ rotate = <270>; -+ bgr; -+ fps = <30>; -+ buswidth = <8>; -+ reset-gpios = <&gpio 23 0>; -+ dc-gpios = <&gpio 24 0>; -+ led-gpios = <&gpio 18 1>; -+ debug = <0>; -+ }; -+ -+ rpidisplay_ts: rpi-display-ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <25 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 25 0>; -+ ti,x-plate-ohms = /bits/ 16 <60>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ __overrides__ { -+ speed = <&rpidisplay>,"spi-max-frequency:0"; -+ rotate = <&rpidisplay>,"rotate:0"; -+ fps = <&rpidisplay>,"fps:0"; -+ debug = <&rpidisplay>,"debug:0"; -+ xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for Rpi-Proto -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&sound>; -+ __overlay__ { -+ compatible = "rpi,rpi-proto"; -+ i2s-controller = <&i2s>; -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&i2s>; -+ __overlay__ { -+ status = "okay"; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ status = "okay"; -+ -+ wm8731@1a { -+ #sound-dai-cells = <0>; -+ compatible = "wlf,wm8731"; -+ reg = <0x1a>; -+ status = "okay"; -+ }; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts -@@ -0,0 +1,78 @@ -+/dts-v1/; -+/plugin/; -+ -+/{ -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target = <&soc>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ sdhost: sdhost@7e202000 { -+ compatible = "brcm,bcm2835-sdhost"; -+ reg = <0x7e202000 0x100>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&sdhost_pins>; -+ interrupts = <2 24>; -+ clocks = <&clk_sdhost>; -+ dmas = <&dma 13>, -+ <&dma 13>; -+ dma-names = "tx", "rx"; -+ brcm,delay-after-stop = <0>; -+ brcm,overclock-50 = <0>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&clocks>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ clk_sdhost: sdhost { -+ compatible = "fixed-clock"; -+ reg = <0>; -+ #clock-cells = <0>; -+ clock-output-names = "sdhost"; -+ clock-frequency = <250000000>; -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&gpio>; -+ __overlay__ { -+ sdhost_pins: sdhost_pins { -+ brcm,pins = <48 49 50 51 52 53>; -+ brcm,function = <4>; /* alt0 */ -+ }; -+ }; -+ }; -+ -+ fragment@3 { -+ target = <&mmc>; -+ __overlay__ { -+ /* Find a way to disable the other driver */ -+ compatible = ""; -+ status = "disabled"; -+ }; -+ }; -+ -+ fragment@4 { -+ target-path = "/__overrides__"; -+ __overlay__ { -+ sdhost_freq = <&clk_sdhost>,"clock-frequency:0"; -+ }; -+ }; -+ -+ __overrides__ { -+ delay_after_stop = <&sdhost>,"brcm,delay-after-stop:0"; -+ overclock_50 = <&sdhost>,"brcm,overclock-50:0"; -+ force_pio = <&sdhost>,"brcm,force-pio?"; -+ sdhost_freq = <&clk_sdhost>,"clock-frequency:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/spi-bcm2708-overlay.dts -@@ -0,0 +1,18 @@ -+/* -+ * Device tree overlay for spi-bcm2835 -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; -+ /* setting up compatiblity to allow loading the spi-bcm2835 driver */ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ compatible = "brcm,bcm2708-spi"; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/spi-bcm2835-overlay.dts -@@ -0,0 +1,18 @@ -+/* -+ * Device tree overlay for spi-bcm2835 -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; -+ /* setting up compatiblity to allow loading the spi-bcm2835 driver */ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ compatible = "brcm,bcm2835-spi"; -+ }; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts -@@ -0,0 +1,216 @@ -+/* -+ * tinylcd35-overlay.dts -+ * -+ * ------------------------------------------------- -+ * www.tinlylcd.com -+ * ------------------------------------------------- -+ * Device---Driver-----BUS GPIO's -+ * display tinylcd35 spi0.0 25 24 18 -+ * touch ads7846 spi0.1 5 -+ * rtc ds1307 i2c1-0068 -+ * rtc pcf8563 i2c1-0051 -+ * keypad gpio-keys --------- 17 22 27 23 28 -+ * -+ * -+ * TinyLCD.com 3.5 inch TFT -+ * -+ * Version 001 -+ * 5/3/2015 -- Noralf Trønnes Initial Device tree framework -+ * 10/3/2015 -- tinylcd@gmail.com added ds1307 support. -+ * -+ */ -+ -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2835", "brcm,bcm2708", "brcm,bcm2709"; -+ -+ fragment@0 { -+ target = <&spi0>; -+ __overlay__ { -+ status = "okay"; -+ -+ spidev@0{ -+ status = "disabled"; -+ }; -+ -+ spidev@1{ -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ tinylcd35_pins: tinylcd35_pins { -+ brcm,pins = <25 24 18>; -+ brcm,function = <1>; /* out */ -+ }; -+ tinylcd35_ts_pins: tinylcd35_ts_pins { -+ brcm,pins = <5>; -+ brcm,function = <0>; /* in */ -+ }; -+ keypad_pins: keypad_pins { -+ brcm,pins = <4 17 22 23 27>; -+ brcm,function = <0>; /* in */ -+ brcm,pull = <1>; /* down */ -+ }; -+ }; -+ }; -+ -+ fragment@2 { -+ target = <&spi0>; -+ __overlay__ { -+ /* needed to avoid dtc warning */ -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ tinylcd35: tinylcd35@0{ -+ compatible = "neosec,tinylcd"; -+ reg = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&tinylcd35_pins>, -+ <&tinylcd35_ts_pins>; -+ -+ spi-max-frequency = <48000000>; -+ rotate = <270>; -+ fps = <20>; -+ bgr; -+ buswidth = <8>; -+ reset-gpios = <&gpio 25 0>; -+ dc-gpios = <&gpio 24 0>; -+ led-gpios = <&gpio 18 1>; -+ debug = <0>; -+ -+ init = <0x10000B0 0x80 -+ 0x10000C0 0x0A 0x0A -+ 0x10000C1 0x01 0x01 -+ 0x10000C2 0x33 -+ 0x10000C5 0x00 0x42 0x80 -+ 0x10000B1 0xD0 0x11 -+ 0x10000B4 0x02 -+ 0x10000B6 0x00 0x22 0x3B -+ 0x10000B7 0x07 -+ 0x1000036 0x58 -+ 0x10000F0 0x36 0xA5 0xD3 -+ 0x10000E5 0x80 -+ 0x10000E5 0x01 -+ 0x10000B3 0x00 -+ 0x10000E5 0x00 -+ 0x10000F0 0x36 0xA5 0x53 -+ 0x10000E0 0x00 0x35 0x33 0x00 0x00 0x00 0x00 0x35 0x33 0x00 0x00 0x00 -+ 0x100003A 0x55 -+ 0x1000011 -+ 0x2000001 -+ 0x1000029>; -+ }; -+ -+ tinylcd35_ts: tinylcd35_ts@1 { -+ compatible = "ti,ads7846"; -+ reg = <1>; -+ status = "disabled"; -+ -+ spi-max-frequency = <2000000>; -+ interrupts = <5 2>; /* high-to-low edge triggered */ -+ interrupt-parent = <&gpio>; -+ pendown-gpio = <&gpio 5 0>; -+ ti,x-plate-ohms = /bits/ 16 <100>; -+ ti,pressure-max = /bits/ 16 <255>; -+ }; -+ }; -+ }; -+ -+ /* RTC */ -+ -+ fragment@3 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ pcf8563: pcf8563@51 { -+ compatible = "nxp,pcf8563"; -+ reg = <0x51>; -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ fragment@4 { -+ target = <&i2c1>; -+ __overlay__ { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ ds1307: ds1307@68 { -+ compatible = "maxim,ds1307"; -+ reg = <0x68>; -+ status = "disabled"; -+ }; -+ }; -+ }; -+ -+ /* -+ * Values for input event code is found under the -+ * 'Keys and buttons' heading in include/uapi/linux/input.h -+ */ -+ fragment@5 { -+ target-path = "/soc"; -+ __overlay__ { -+ keypad: keypad { -+ compatible = "gpio-keys"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&keypad_pins>; -+ status = "disabled"; -+ autorepeat; -+ -+ button@17 { -+ label = "GPIO KEY_UP"; -+ linux,code = <103>; -+ gpios = <&gpio 17 0>; -+ }; -+ button@22 { -+ label = "GPIO KEY_DOWN"; -+ linux,code = <108>; -+ gpios = <&gpio 22 0>; -+ }; -+ button@27 { -+ label = "GPIO KEY_LEFT"; -+ linux,code = <105>; -+ gpios = <&gpio 27 0>; -+ }; -+ button@23 { -+ label = "GPIO KEY_RIGHT"; -+ linux,code = <106>; -+ gpios = <&gpio 23 0>; -+ }; -+ button@4 { -+ label = "GPIO KEY_ENTER"; -+ linux,code = <28>; -+ gpios = <&gpio 4 0>; -+ }; -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ speed = <&tinylcd35>,"spi-max-frequency:0"; -+ rotate = <&tinylcd35>,"rotate:0"; -+ fps = <&tinylcd35>,"fps:0"; -+ debug = <&tinylcd35>,"debug:0"; -+ touch = <&tinylcd35_ts>,"status"; -+ touchgpio = <&tinylcd35_ts_pins>,"brcm,pins:0", -+ <&tinylcd35_ts>,"interrupts:0", -+ <&tinylcd35_ts>,"pendown-gpio:4"; -+ xohms = <&tinylcd35_ts>,"ti,x-plate-ohms;0"; -+ rtc-pcf = <&i2c1>,"status", -+ <&pcf8563>,"status"; -+ rtc-ds = <&i2c1>,"status", -+ <&ds1307>,"status"; -+ keypad = <&keypad>,"status"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts -@@ -0,0 +1,39 @@ -+// Definitions for w1-gpio module (without external pullup) -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ -+ w1: onewire@0 { -+ compatible = "w1-gpio"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&w1_pins>; -+ gpios = <&gpio 4 0>; -+ rpi,parasitic-power = <0>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ w1_pins: w1_pins { -+ brcm,pins = <4>; -+ brcm,function = <0>; // in (initially) -+ brcm,pull = <0>; // off -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ gpiopin = <&w1>,"gpios:4", -+ <&w1_pins>,"brcm,pins:0"; -+ pullup = <&w1>,"rpi,parasitic-power:0"; -+ }; -+}; ---- /dev/null -+++ b/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts -@@ -0,0 +1,41 @@ -+// Definitions for w1-gpio module (with external pullup) -+/dts-v1/; -+/plugin/; -+ -+/ { -+ compatible = "brcm,bcm2708"; -+ -+ fragment@0 { -+ target-path = "/"; -+ __overlay__ { -+ -+ w1: onewire@0 { -+ compatible = "w1-gpio"; -+ pinctrl-names = "default"; -+ pinctrl-0 = <&w1_pins>; -+ gpios = <&gpio 4 0>, <&gpio 5 1>; -+ rpi,parasitic-power = <0>; -+ status = "okay"; -+ }; -+ }; -+ }; -+ -+ fragment@1 { -+ target = <&gpio>; -+ __overlay__ { -+ w1_pins: w1_pins { -+ brcm,pins = <4 5>; -+ brcm,function = <0 1>; // in out -+ brcm,pull = <0 0>; // off off -+ }; -+ }; -+ }; -+ -+ __overrides__ { -+ gpiopin = <&w1>,"gpios:4", -+ <&w1_pins>,"brcm,pins:0"; -+ extpullup = <&w1>,"gpios:16", -+ <&w1_pins>,"brcm,pins:4"; -+ pullup = <&w1>,"rpi,parasitic-power:0"; -+ }; -+}; |