ipq806x: Add support for linux-4.4

1)Changes

- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime

2)Testing

Tested on IPQ AP148 Board:
 a. NOR boot and NAND boot
 b. ethernet network and ath10k wifi
 c. ubi sysupgrade

UnTested
 dwc3 usb has not been validated on IPQ board(AP148)

3)Known Issues:
 Once we flash ubi image on AP148, and if we reset the board, uboot on
 first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
 and not what linux expects which causes errors when trying to mount rootfs.
 In order to test this, we can use the below steps:
  a. Flash the ubi image on board and don't reset the board
  b. load the kernel fit image in RAM and boot from there.

Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>

1 files changed, 311 insertions, 0 deletions

diff --git a/target/linux/ipq806x/patches-4.4/114-pcie-add-ctlr-init.patch b/target/linux/ipq806x/patches-4.4/114-pcie-add-ctlr-init.patch
new file mode 100644
index 0000000000..6328113c06
--- /dev/null
+++ b/target/linux/ipq806x/patches-4.4/114-pcie-add-ctlr-init.patch
@@ -0,0 +1,311 @@
+--- a/drivers/pci/host/pcie-qcom.c
++++ b/drivers/pci/host/pcie-qcom.c
+@@ -29,8 +29,53 @@
+ 
+ #include "pcie-designware.h"
+ 
++/* DBI registers */
++#define PCIE20_CAP				0x70
++#define PCIE20_CAP_LINKCTRLSTATUS		(PCIE20_CAP + 0x10)
++
++#define PCIE20_AXI_MSTR_RESP_COMP_CTRL0		0x818
++#define PCIE20_AXI_MSTR_RESP_COMP_CTRL1		0x81c
++
++#define PCIE20_PLR_IATU_VIEWPORT		0x900
++#define PCIE20_PLR_IATU_REGION_OUTBOUND		(0x0 << 31)
++#define PCIE20_PLR_IATU_REGION_INDEX(x)		(x << 0)
++
++#define PCIE20_PLR_IATU_CTRL1			0x904
++#define PCIE20_PLR_IATU_TYPE_CFG0		(0x4 << 0)
++#define PCIE20_PLR_IATU_TYPE_MEM		(0x0 << 0)
++
++#define PCIE20_PLR_IATU_CTRL2			0x908
++#define PCIE20_PLR_IATU_ENABLE			BIT(31)
++
++#define PCIE20_PLR_IATU_LBAR			0x90C
++#define PCIE20_PLR_IATU_UBAR			0x910
++#define PCIE20_PLR_IATU_LAR			0x914
++#define PCIE20_PLR_IATU_LTAR			0x918
++#define PCIE20_PLR_IATU_UTAR			0x91c
++
++#define MSM_PCIE_DEV_CFG_ADDR			0x01000000
++
++/* PARF registers */
++#define PCIE20_PARF_PCS_DEEMPH			0x34
++#define PCS_DEEMPH_TX_DEEMPH_GEN1(x)		(x << 16)
++#define PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(x)	(x << 8)
++#define PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(x)	(x << 0)
++
++#define PCIE20_PARF_PCS_SWING			0x38
++#define PCS_SWING_TX_SWING_FULL(x)		(x << 8)
++#define PCS_SWING_TX_SWING_LOW(x)		(x << 0)
++
+ #define PCIE20_PARF_PHY_CTRL			0x40
++#define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK	(0x1f << 16)
++#define PHY_CTRL_PHY_TX0_TERM_OFFSET(x)		(x << 16)
++
+ #define PCIE20_PARF_PHY_REFCLK			0x4C
++#define REF_SSP_EN				BIT(16)
++#define REF_USE_PAD				BIT(12)
++
++#define PCIE20_PARF_CONFIG_BITS			0x50
++#define PHY_RX0_EQ(x)				(x << 24)
++
+ #define PCIE20_PARF_DBI_BASE_ADDR		0x168
+ #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16c
+ #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT	0x178
+@@ -39,9 +84,6 @@
+ #define PCIE20_ELBI_SYS_STTS			0x08
+ #define XMLH_LINK_UP				BIT(10)
+ 
+-#define PCIE20_CAP				0x70
+-#define PCIE20_CAP_LINKCTRLSTATUS		(PCIE20_CAP + 0x10)
+-
+ #define PERST_DELAY_MIN_US			1000
+ #define PERST_DELAY_MAX_US			1005
+ 
+@@ -56,14 +98,18 @@ struct qcom_pcie_resources_v0 {
+ 	struct clk *iface_clk;
+ 	struct clk *core_clk;
+ 	struct clk *phy_clk;
++	struct clk *aux_clk;
++	struct clk *ref_clk;
+ 	struct reset_control *pci_reset;
+ 	struct reset_control *axi_reset;
+ 	struct reset_control *ahb_reset;
+ 	struct reset_control *por_reset;
+ 	struct reset_control *phy_reset;
++	struct reset_control *ext_reset;
+ 	struct regulator *vdda;
+ 	struct regulator *vdda_phy;
+ 	struct regulator *vdda_refclk;
++	uint8_t phy_tx0_term_offset;
+ };
+ 
+ struct qcom_pcie_resources_v1 {
+@@ -106,20 +152,10 @@ writel_masked(void __iomem *addr, u32 cl
+ 
+ static void qcom_ep_reset_assert_deassert(struct qcom_pcie *pcie, int assert)
+ {
+-	int val, active_low;
+-
+ 	if (IS_ERR_OR_NULL(pcie->reset))
+ 		return;
+ 
+-	active_low = gpiod_is_active_low(pcie->reset);
+-
+-	if (assert)
+-		val = !!active_low;
+-	else
+-		val = !active_low;
+-
+-	gpiod_set_value(pcie->reset, val);
+-
++	gpiod_set_value(pcie->reset, assert);
+ 	usleep_range(PERST_DELAY_MIN_US, PERST_DELAY_MAX_US);
+ }
+ 
+@@ -156,10 +192,13 @@ static void qcom_pcie_disable_resources_
+ 	reset_control_assert(res->axi_reset);
+ 	reset_control_assert(res->ahb_reset);
+ 	reset_control_assert(res->por_reset);
+-	reset_control_assert(res->pci_reset);
++	reset_control_assert(res->phy_reset);
++	reset_control_assert(res->ext_reset);
+ 	clk_disable_unprepare(res->iface_clk);
+ 	clk_disable_unprepare(res->core_clk);
+ 	clk_disable_unprepare(res->phy_clk);
++	clk_disable_unprepare(res->aux_clk);
++	clk_disable_unprepare(res->ref_clk);
+ 	regulator_disable(res->vdda);
+ 	regulator_disable(res->vdda_phy);
+ 	regulator_disable(res->vdda_refclk);
+@@ -201,6 +240,12 @@ static int qcom_pcie_enable_resources_v0
+ 		goto err_vdda_phy;
+ 	}
+ 
++	ret = reset_control_deassert(res->ext_reset);
++	if (ret) {
++		dev_err(dev, "cannot assert ext reset\n");
++		goto err_reset_ext;
++	}
++
+ 	ret = clk_prepare_enable(res->iface_clk);
+ 	if (ret) {
+ 		dev_err(dev, "cannot prepare/enable iface clock\n");
+@@ -219,21 +264,40 @@ static int qcom_pcie_enable_resources_v0
+ 		goto err_clk_phy;
+ 	}
+ 
++	ret = clk_prepare_enable(res->aux_clk);
++	if (ret) {
++		dev_err(dev, "cannot prepare/enable aux clock\n");
++		goto err_clk_aux;
++	}
++
++	ret = clk_prepare_enable(res->ref_clk);
++	if (ret) {
++		dev_err(dev, "cannot prepare/enable ref clock\n");
++		goto err_clk_ref;
++	}
++
+ 	ret = reset_control_deassert(res->ahb_reset);
+ 	if (ret) {
+ 		dev_err(dev, "cannot deassert ahb reset\n");
+ 		goto err_reset_ahb;
+ 	}
++	udelay(1);
+ 
+ 	return 0;
+ 
+ err_reset_ahb:
++	clk_disable_unprepare(res->ref_clk);
++err_clk_ref:
++	clk_disable_unprepare(res->aux_clk);
++err_clk_aux:
+ 	clk_disable_unprepare(res->phy_clk);
+ err_clk_phy:
+ 	clk_disable_unprepare(res->core_clk);
+ err_clk_core:
+ 	clk_disable_unprepare(res->iface_clk);
+ err_iface:
++	reset_control_assert(res->ext_reset);
++err_reset_ext:
+ 	regulator_disable(res->vdda_phy);
+ err_vdda_phy:
+ 	regulator_disable(res->vdda_refclk);
+@@ -329,6 +393,14 @@ static int qcom_pcie_get_resources_v0(st
+ 	if (IS_ERR(res->phy_clk))
+ 		return PTR_ERR(res->phy_clk);
+ 
++	res->aux_clk = devm_clk_get(dev, "aux");
++	if (IS_ERR(res->aux_clk))
++		return PTR_ERR(res->aux_clk);
++
++	res->ref_clk = devm_clk_get(dev, "ref");
++	if (IS_ERR(res->ref_clk))
++		return PTR_ERR(res->ref_clk);
++
+ 	res->pci_reset = devm_reset_control_get(dev, "pci");
+ 	if (IS_ERR(res->pci_reset))
+ 		return PTR_ERR(res->pci_reset);
+@@ -349,6 +421,14 @@ static int qcom_pcie_get_resources_v0(st
+ 	if (IS_ERR(res->phy_reset))
+ 		return PTR_ERR(res->phy_reset);
+ 
++	res->ext_reset = devm_reset_control_get(dev, "ext");
++	if (IS_ERR(res->ext_reset))
++		return PTR_ERR(res->ext_reset);
++
++	if (of_property_read_u8(dev->of_node, "phy-tx0-term-offset",
++				&res->phy_tx0_term_offset))
++		res->phy_tx0_term_offset = 0;
++
+ 	return 0;
+ }
+ 
+@@ -461,6 +541,57 @@ err_res:
+ 	qcom_pcie_disable_resources_v1(pcie);
+ }
+ 
++static void qcom_pcie_prog_viewport_cfg0(struct qcom_pcie *pcie, u32 busdev)
++{
++	struct pcie_port *pp = &pcie->pp;
++
++	/*
++	 * program and enable address translation region 0 (device config
++	 * address space); region type config;
++	 * axi config address range to device config address range
++	 */
++	writel(PCIE20_PLR_IATU_REGION_OUTBOUND |
++	       PCIE20_PLR_IATU_REGION_INDEX(0),
++	       pcie->dbi + PCIE20_PLR_IATU_VIEWPORT);
++
++	writel(PCIE20_PLR_IATU_TYPE_CFG0, pcie->dbi + PCIE20_PLR_IATU_CTRL1);
++	writel(PCIE20_PLR_IATU_ENABLE, pcie->dbi + PCIE20_PLR_IATU_CTRL2);
++	writel(pp->cfg0_base, pcie->dbi + PCIE20_PLR_IATU_LBAR);
++	writel((pp->cfg0_base >> 32), pcie->dbi + PCIE20_PLR_IATU_UBAR);
++	writel((pp->cfg0_base + pp->cfg0_size - 1),
++	       pcie->dbi + PCIE20_PLR_IATU_LAR);
++	writel(busdev, pcie->dbi + PCIE20_PLR_IATU_LTAR);
++	writel(0, pcie->dbi + PCIE20_PLR_IATU_UTAR);
++}
++
++static void qcom_pcie_prog_viewport_mem2_outbound(struct qcom_pcie *pcie)
++{
++	struct pcie_port *pp = &pcie->pp;
++
++	/*
++	 * program and enable address translation region 2 (device resource
++	 * address space); region type memory;
++	 * axi device bar address range to device bar address range
++	 */
++	writel(PCIE20_PLR_IATU_REGION_OUTBOUND |
++	       PCIE20_PLR_IATU_REGION_INDEX(2),
++	       pcie->dbi + PCIE20_PLR_IATU_VIEWPORT);
++
++	writel(PCIE20_PLR_IATU_TYPE_MEM, pcie->dbi + PCIE20_PLR_IATU_CTRL1);
++	writel(PCIE20_PLR_IATU_ENABLE, pcie->dbi + PCIE20_PLR_IATU_CTRL2);
++	writel(pp->mem_base, pcie->dbi + PCIE20_PLR_IATU_LBAR);
++	writel((pp->mem_base >> 32), pcie->dbi + PCIE20_PLR_IATU_UBAR);
++	writel(pp->mem_base + pp->mem_size - 1,
++	       pcie->dbi + PCIE20_PLR_IATU_LAR);
++	writel(pp->mem_bus_addr, pcie->dbi + PCIE20_PLR_IATU_LTAR);
++	writel(upper_32_bits(pp->mem_bus_addr),
++	       pcie->dbi + PCIE20_PLR_IATU_UTAR);
++
++	/* 256B PCIE buffer setting */
++	writel(0x1, pcie->dbi + PCIE20_AXI_MSTR_RESP_COMP_CTRL0);
++	writel(0x1, pcie->dbi + PCIE20_AXI_MSTR_RESP_COMP_CTRL1);
++}
++
+ static void qcom_pcie_host_init_v0(struct pcie_port *pp)
+ {
+ 	struct qcom_pcie *pcie = to_qcom_pcie(pp);
+@@ -470,15 +601,34 @@ static void qcom_pcie_host_init_v0(struc
+ 
+ 	qcom_ep_reset_assert(pcie);
+ 
++	reset_control_assert(res->ahb_reset);
++
+ 	ret = qcom_pcie_enable_resources_v0(pcie);
+ 	if (ret)
+ 		return;
+ 
+ 	writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL, BIT(0), 0);
+ 
+-	/* enable external reference clock */
+-	writel_masked(pcie->parf + PCIE20_PARF_PHY_REFCLK, 0, BIT(16));
++	/* Set Tx termination offset */
++	writel_masked(pcie->parf + PCIE20_PARF_PHY_CTRL,
++		      PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK,
++		      PHY_CTRL_PHY_TX0_TERM_OFFSET(res->phy_tx0_term_offset));
++
++	/* PARF programming */
++	writel(PCS_DEEMPH_TX_DEEMPH_GEN1(0x18) |
++	       PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(0x18) |
++	       PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(0x22),
++	       pcie->parf + PCIE20_PARF_PCS_DEEMPH);
++	writel(PCS_SWING_TX_SWING_FULL(0x78) |
++	       PCS_SWING_TX_SWING_LOW(0x78),
++	       pcie->parf + PCIE20_PARF_PCS_SWING);
++	writel(PHY_RX0_EQ(0x4), pcie->parf + PCIE20_PARF_CONFIG_BITS);
++
++	/* Enable reference clock */
++	writel_masked(pcie->parf + PCIE20_PARF_PHY_REFCLK,
++		      REF_USE_PAD, REF_SSP_EN);
+ 
++	/* De-assert PHY, PCIe, POR and AXI resets */
+ 	ret = reset_control_deassert(res->phy_reset);
+ 	if (ret) {
+ 		dev_err(dev, "cannot deassert phy reset\n");
+@@ -517,6 +667,9 @@ static void qcom_pcie_host_init_v0(struc
+ 	if (ret)
+ 		goto err;
+ 
++	qcom_pcie_prog_viewport_cfg0(pcie, MSM_PCIE_DEV_CFG_ADDR);
++	qcom_pcie_prog_viewport_mem2_outbound(pcie);
++
+ 	return;
+ err:
+ 	qcom_ep_reset_assert(pcie);