diff options
Diffstat (limited to 'target/linux/etrax-2.6/patches/cris/003-drivers-cris.patch')
| -rw-r--r-- | target/linux/etrax-2.6/patches/cris/003-drivers-cris.patch | 22601 |
1 files changed, 22601 insertions, 0 deletions
diff --git a/target/linux/etrax-2.6/patches/cris/003-drivers-cris.patch b/target/linux/etrax-2.6/patches/cris/003-drivers-cris.patch new file mode 100644 index 0000000000..1f42fc86e6 --- /dev/null +++ b/target/linux/etrax-2.6/patches/cris/003-drivers-cris.patch @@ -0,0 +1,22601 @@ +diff -urN linux-2.6.19.2.orig/drivers/ide/cris/ide-cris.c linux-2.6.19.2.dev/drivers/ide/cris/ide-cris.c +--- linux-2.6.19.2.orig/drivers/ide/cris/ide-cris.c 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/ide/cris/ide-cris.c 2006-12-06 14:17:02.000000000 +0100 +@@ -1,8 +1,8 @@ +-/* $Id: cris-ide-driver.patch,v 1.1 2005/06/29 21:39:07 akpm Exp $ ++/* $Id: ide-cris.c,v 1.10 2006/12/06 13:17:02 starvik Exp $ + * + * Etrax specific IDE functions, like init and PIO-mode setting etc. + * Almost the entire ide.c is used for the rest of the Etrax ATA driver. +- * Copyright (c) 2000-2005 Axis Communications AB ++ * Copyright (c) 2000-2006 Axis Communications AB + * + * Authors: Bjorn Wesen (initial version) + * Mikael Starvik (crisv32 port) +@@ -43,8 +43,8 @@ + + #define IDE_REGISTER_TIMEOUT 300 + +-#define LOWDB(x) +-#define D(x) ++#define LOWDB(x) ++#define D(x) + + enum /* Transfer types */ + { +@@ -88,12 +88,50 @@ + #define ATA_PIO0_STROBE 39 + #define ATA_PIO0_HOLD 9 + +-int ++/* ++ * On ETRAX FS, an interrupt remains latched and active until ack:ed. ++ * Further, ATA acks are without effect as long as INTRQ is asserted, as the ++ * corresponding ATA interrupt is continuously set to active. There will be a ++ * clearing ack at the usual cris_ide_ack_intr call, but that serves just to ++ * gracefully handle an actual spurious interrupt or similar situation (which ++ * will cause an early return without further actions, see the ide_intr ++ * function). ++ * ++ * However, the normal case at time of this writing is that nothing has ++ * changed from when INTRQ was asserted until the cris_ide_ack_intr call; no ++ * ATA registers written and no status register read, so INTRQ will *remain* ++ * asserted, thus *another* interrupt will be latched, and will be seen as a ++ * spurious interrupt after the "real" interrupt is serviced. With lots of ++ * ATA traffic (as in a trivial file-copy between two drives), this will trig ++ * the condition desc->irqs_unhandled > 99900 in ++ * kernel/irq/spurious.c:note_interrupt and the system will halt. ++ * ++ * To actually get rid of the interrupt corresponding to the current INTRQ ++ * assertion, we make a second ack after the next ATA register read or write; ++ * i.e. when INTRQ must be deasserted. At that time, we don't have the hwif ++ * pointer available, so we need to stash a local copy (safe, because it'll be ++ * set and cleared within the same spin_lock_irqsave region). The pointer ++ * serves doubly as a boolean flag that an ack is needed. The caller must ++ * NULL the pointer after the "second ack". ++ */ ++ ++static ide_hwif_t *hwif_to_ack; ++ ++static int + cris_ide_ack_intr(ide_hwif_t* hwif) + { +- reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, ++ /* ++ * The interrupt is shared so we need to find the interface bit number ++ * to ack. We define the ATA I/O register addresses to have the ++ * format of ata rw_ctrl2 register contents, conveniently holding this ++ * number. ++ */ ++ reg_ata_rw_ctrl2 ctrl2 = REG_TYPE_CONV(reg_ata_rw_ctrl2, + int, hwif->io_ports[0]); + REG_WR_INT(ata, regi_ata, rw_ack_intr, 1 << ctrl2.sel); ++ ++ /* Prepare to ack again, see above. */ ++ hwif_to_ack = hwif; + return 1; + } + +@@ -122,8 +160,24 @@ + + static void + cris_ide_write_command(unsigned long command) +-{ ++{ + REG_WR_INT(ata, regi_ata, rw_ctrl2, command); /* write data to the drive's register */ ++ ++ /* ++ * Perform a pending ack if needed; see hwif_ack definition. Perhaps ++ * we should check closer that this call is really a part of the ++ * preparation to read the ATA status register or write to the ATA ++ * command register (causing deassert of INTRQ; see the ATA standard), ++ * but at time of this writing (and expected to sanely remain so), the ++ * first ATA register activity after an cris_ide_ack_intr call is ++ * certain to do exactly that. ++ */ ++ if (hwif_to_ack) { ++ /* The drive may take this long to deassert INTRQ. */ ++ ndelay(400); ++ cris_ide_ack_intr(hwif_to_ack); ++ hwif_to_ack = NULL; ++ } + } + + static void +@@ -160,8 +214,8 @@ + { + reg_ata_rw_ctrl2 ctrl2 = {0}; + ctrl2.addr = addr; +- ctrl2.cs1 = cs1; +- ctrl2.cs0 = cs0; ++ ctrl2.cs1 = !cs1; ++ ctrl2.cs0 = !cs0; + return REG_TYPE_CONV(int, reg_ata_rw_ctrl2, ctrl2); + } + +@@ -184,14 +238,14 @@ + + intr_mask.bus0 = regk_ata_yes; + intr_mask.bus1 = regk_ata_yes; +- intr_mask.bus2 = regk_ata_yes; ++ intr_mask.bus2 = regk_ata_yes; + intr_mask.bus3 = regk_ata_yes; + + REG_WR(ata, regi_ata, rw_intr_mask, intr_mask); + + crisv32_request_dma(2, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata); + crisv32_request_dma(3, "ETRAX FS built-in ATA", DMA_VERBOSE_ON_ERROR, 0, dma_ata); +- ++ + crisv32_pinmux_alloc_fixed(pinmux_ata); + crisv32_pinmux_alloc_fixed(pinmux_ata0); + crisv32_pinmux_alloc_fixed(pinmux_ata1); +@@ -204,14 +258,15 @@ + DMA_ENABLE(regi_dma3); + + DMA_WR_CMD (regi_dma2, regk_dma_set_w_size2); +- DMA_WR_CMD (regi_dma3, regk_dma_set_w_size2); ++ DMA_WR_CMD (regi_dma3, regk_dma_set_w_size2); + } + + static dma_descr_context mycontext __attribute__ ((__aligned__(32))); + + #define cris_dma_descr_type dma_descr_data +-#define cris_pio_read regk_ata_rd +-#define cris_ultra_mask 0x7 ++#define cris_pio_read (regk_ata_rd << 24) ++#define cris_ultra_mask 0x0 /* 0x7 for UDMA */ ++#define IRQ ATA_INTR_VECT + #define MAX_DESCR_SIZE 0xffffffffUL + + static unsigned long +@@ -226,6 +281,8 @@ + d->buf = (char*)virt_to_phys(buf); + d->after = d->buf + len; + d->eol = last; ++ /* assume descriptors are consecutively placed in memory */ ++ d->next = last ? 0 : (cris_dma_descr_type*)virt_to_phys(d+1); + } + + static void +@@ -237,8 +294,10 @@ + mycontext.saved_data = (dma_descr_data*)virt_to_phys(d); + mycontext.saved_data_buf = d->buf; + /* start the dma channel */ ++ if (dir) ++ flush_dma_context(&mycontext); // Cache bug workaround + DMA_START_CONTEXT(dir ? regi_dma3 : regi_dma2, virt_to_phys(&mycontext)); +- ++ + /* initiate a multi word dma read using PIO handshaking */ + trf_cnt.cnt = len >> 1; + /* Due to a "feature" the transfer count has to be one extra word for UDMA. */ +@@ -248,7 +307,7 @@ + + ctrl2.rw = dir ? regk_ata_rd : regk_ata_wr; + ctrl2.trf_mode = regk_ata_dma; +- ctrl2.hsh = type == TYPE_PIO ? regk_ata_pio : ++ ctrl2.hsh = type == TYPE_PIO ? regk_ata_pio : + type == TYPE_DMA ? regk_ata_dma : regk_ata_udma; + ctrl2.multi = regk_ata_yes; + ctrl2.dma_size = regk_ata_word; +@@ -339,7 +398,7 @@ + #define ATA_PIO0_STROBE 19 + #define ATA_PIO0_HOLD 4 + +-int ++int + cris_ide_ack_intr(ide_hwif_t* hwif) + { + return 1; +@@ -348,13 +407,13 @@ + static inline int + cris_ide_busy(void) + { +- return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy) ; ++ return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, busy) ; + } + + static inline int + cris_ide_ready(void) + { +- return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy) ; ++ return *R_ATA_STATUS_DATA & IO_MASK(R_ATA_STATUS_DATA, tr_rdy) ; + } + + static inline int +@@ -364,12 +423,12 @@ + *data = (unsigned short)status; + return status & IO_MASK(R_ATA_STATUS_DATA, dav); + } +- ++ + static void + cris_ide_write_command(unsigned long command) + { +- *R_ATA_CTRL_DATA = command; +-} ++ *R_ATA_CTRL_DATA = command; ++} + + static void + cris_ide_set_speed(int type, int setup, int strobe, int hold) +@@ -406,8 +465,8 @@ + cris_ide_reg_addr(unsigned long addr, int cs0, int cs1) + { + return IO_FIELD(R_ATA_CTRL_DATA, addr, addr) | +- IO_FIELD(R_ATA_CTRL_DATA, cs0, cs0) | +- IO_FIELD(R_ATA_CTRL_DATA, cs1, cs1); ++ IO_FIELD(R_ATA_CTRL_DATA, cs0, cs0 ? 0 : 1) | ++ IO_FIELD(R_ATA_CTRL_DATA, cs1, cs1 ? 0 : 1); + } + + static __init void +@@ -484,6 +543,7 @@ + #define cris_dma_descr_type etrax_dma_descr + #define cris_pio_read IO_STATE(R_ATA_CTRL_DATA, rw, read) + #define cris_ultra_mask 0x0 ++#define IRQ 4 + #define MAX_DESCR_SIZE 0x10000UL + + static unsigned long +@@ -497,8 +557,8 @@ + { + d->buf = virt_to_phys(buf); + d->sw_len = len == MAX_DESCR_SIZE ? 0 : len; +- if (last) +- d->ctrl |= d_eol; ++ d->ctrl = last ? d_eol : 0; ++ d->next = last ? 0 : virt_to_phys(d+1); /* assumes descr's in array */ + } + + static void cris_ide_start_dma(ide_drive_t *drive, cris_dma_descr_type *d, int dir, int type, int len) +@@ -521,14 +581,14 @@ + *R_DMA_CH2_FIRST = virt_to_phys(d); + *R_DMA_CH2_CMD = IO_STATE(R_DMA_CH2_CMD, cmd, start); + } +- ++ + /* initiate a multi word dma read using DMA handshaking */ + + *R_ATA_TRANSFER_CNT = + IO_FIELD(R_ATA_TRANSFER_CNT, count, len >> 1); + + cmd = dir ? IO_STATE(R_ATA_CTRL_DATA, rw, read) : IO_STATE(R_ATA_CTRL_DATA, rw, write); +- cmd |= type == TYPE_PIO ? IO_STATE(R_ATA_CTRL_DATA, handsh, pio) : ++ cmd |= type == TYPE_PIO ? IO_STATE(R_ATA_CTRL_DATA, handsh, pio) : + IO_STATE(R_ATA_CTRL_DATA, handsh, dma); + *R_ATA_CTRL_DATA = + cmd | +@@ -570,7 +630,7 @@ + } + + #endif +- ++ + void + cris_ide_outw(unsigned short data, unsigned long reg) { + int timeleft; +@@ -597,7 +657,7 @@ + if(!timeleft) + printk("ATA timeout reg 0x%lx := 0x%x\n", reg, data); + +- cris_ide_write_command(reg|data); /* write data to the drive's register */ ++ cris_ide_write_command(reg|data); /* write data to the drive's register */ + + timeleft = IDE_REGISTER_TIMEOUT; + /* wait for transmitter ready */ +@@ -684,13 +744,15 @@ + static void cris_atapi_output_bytes(ide_drive_t *drive, void *, unsigned int); + static int cris_dma_off (ide_drive_t *drive); + static int cris_dma_on (ide_drive_t *drive); ++static int cris_dma_host_off (ide_drive_t *drive); ++static int cris_dma_host_on (ide_drive_t *drive); + + static void tune_cris_ide(ide_drive_t *drive, u8 pio) + { + int setup, strobe, hold; + + switch(pio) +- { ++ { + case 0: + setup = ATA_PIO0_SETUP; + strobe = ATA_PIO0_STROBE; +@@ -715,7 +777,7 @@ + setup = ATA_PIO4_SETUP; + strobe = ATA_PIO4_STROBE; + hold = ATA_PIO4_HOLD; +- break; ++ break; + default: + return; + } +@@ -733,7 +795,7 @@ + } + + switch(speed) +- { ++ { + case XFER_UDMA_0: + cyc = ATA_UDMA0_CYC; + dvs = ATA_UDMA0_DVS; +@@ -765,7 +827,7 @@ + if (speed >= XFER_UDMA_0) + cris_ide_set_speed(TYPE_UDMA, cyc, dvs, 0); + else +- cris_ide_set_speed(TYPE_DMA, 0, strobe, hold); ++ cris_ide_set_speed(TYPE_DMA, 0, strobe, hold); + + return 0; + } +@@ -790,11 +852,13 @@ + + for(h = 0; h < MAX_HWIFS; h++) { + ide_hwif_t *hwif = &ide_hwifs[h]; +- ide_setup_ports(&hw, cris_ide_base_address(h), ++ memset(&hw, 0, sizeof(hw)); ++ ide_setup_ports(&hw, cris_ide_base_address(h), + ide_offsets, + 0, 0, cris_ide_ack_intr, +- ide_default_irq(0)); ++ IRQ); + ide_register_hw(&hw, &hwif); ++ hwif->irq = IRQ; + hwif->mmio = 2; + hwif->chipset = ide_etrax100; + hwif->tuneproc = &tune_cris_ide; +@@ -814,13 +878,15 @@ + hwif->OUTBSYNC = &cris_ide_outbsync; + hwif->INB = &cris_ide_inb; + hwif->INW = &cris_ide_inw; +- hwif->ide_dma_host_off = &cris_dma_off; +- hwif->ide_dma_host_on = &cris_dma_on; ++ hwif->ide_dma_host_off = &cris_dma_host_off; ++ hwif->ide_dma_host_on = &cris_dma_host_on; + hwif->ide_dma_off_quietly = &cris_dma_off; ++ hwif->ide_dma_on = &cris_dma_on; + hwif->udma_four = 0; + hwif->ultra_mask = cris_ultra_mask; + hwif->mwdma_mask = 0x07; /* Multiword DMA 0-2 */ + hwif->swdma_mask = 0x07; /* Singleword DMA 0-2 */ ++ hwif->rqsize = 256; + } + + /* Reset pulse */ +@@ -835,13 +901,25 @@ + cris_ide_set_speed(TYPE_UDMA, ATA_UDMA2_CYC, ATA_UDMA2_DVS, 0); + } + ++static int cris_dma_host_off (ide_drive_t *drive) ++{ ++ return 0; ++} ++ ++static int cris_dma_host_on (ide_drive_t *drive) ++{ ++ return 0; ++} ++ + static int cris_dma_off (ide_drive_t *drive) + { ++ drive->using_dma = 0; + return 0; + } + + static int cris_dma_on (ide_drive_t *drive) + { ++ drive->using_dma = 1; + return 0; + } + +@@ -958,30 +1036,28 @@ + size += sg_dma_len(sg); + } + +- /* did we run out of descriptors? */ +- +- if(count >= MAX_DMA_DESCRS) { +- printk("%s: too few DMA descriptors\n", drive->name); +- return 1; +- } +- +- /* however, this case is more difficult - rw_trf_cnt cannot be more +- than 65536 words per transfer, so in that case we need to either ++ /* rw_trf_cnt cannot be more than 131072 words per transfer, ++ (- 1 word for UDMA CRC) so in that case we need to either: + 1) use a DMA interrupt to re-trigger rw_trf_cnt and continue with + the descriptors, or + 2) simply do the request here, and get dma_intr to only ide_end_request on + those blocks that were actually set-up for transfer. ++ (The ide framework will issue a new request for the remainder) + */ + +- if(ata_tot_size + size > 131072) { ++ if(ata_tot_size + size > 262140) { + printk("too large total ATA DMA request, %d + %d!\n", ata_tot_size, (int)size); + return 1; + } + +- /* If size > MAX_DESCR_SIZE it has to be splitted into new descriptors. Since we +- don't handle size > 131072 only one split is necessary */ ++ /* If size > MAX_DESCR_SIZE it has to be splitted into new descriptors. */ + +- if(size > MAX_DESCR_SIZE) { ++ while (size > MAX_DESCR_SIZE) { ++ /* did we run out of descriptors? */ ++ if(count >= MAX_DMA_DESCRS) { ++ printk("%s: too few DMA descriptors\n", drive->name); ++ return 1; ++ } + cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, MAX_DESCR_SIZE, 0); + count++; + ata_tot_size += MAX_DESCR_SIZE; +@@ -989,6 +1065,11 @@ + addr += MAX_DESCR_SIZE; + } + ++ /* did we run out of descriptors? */ ++ if(count >= MAX_DMA_DESCRS) { ++ printk("%s: too few DMA descriptors\n", drive->name); ++ return 1; ++ } + cris_ide_fill_descriptor(&ata_descrs[count], (void*)addr, size,i ? 0 : 1); + count++; + ata_tot_size += size; +@@ -1050,8 +1131,12 @@ + + if (id && (id->capability & 1)) { + if (ide_use_dma(drive)) { +- if (cris_config_drive_for_dma(drive)) +- return hwif->ide_dma_on(drive); ++ if (cris_config_drive_for_dma(drive)) { ++ if (hwif->ide_dma_on) ++ return hwif->ide_dma_on(drive); ++ else ++ return 1; ++ } + } + } + +--- linux-2.6.19.2.orig/drivers/serial/crisv10.c 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/serial/crisv10.c 2007-01-09 10:30:54.000000000 +0100 +@@ -2,7 +2,7 @@ + * + * Serial port driver for the ETRAX 100LX chip + * +- * Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003 Axis Communications AB ++ * Copyright (C) 1998, 1999, 2000, 2001, 2002, 2003, 2004 Axis Communications AB + * + * Many, many authors. Based once upon a time on serial.c for 16x50. + * +@@ -445,6 +445,7 @@ + + #include <asm/io.h> + #include <asm/irq.h> ++#include <asm/dma.h> + #include <asm/system.h> + #include <asm/bitops.h> + #include <linux/delay.h> +@@ -454,8 +455,9 @@ + /* non-arch dependent serial structures are in linux/serial.h */ + #include <linux/serial.h> + /* while we keep our own stuff (struct e100_serial) in a local .h file */ +-#include "serial.h" ++#include "crisv10.h" + #include <asm/fasttimer.h> ++#include <asm/arch/io_interface_mux.h> + + #ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER + #ifndef CONFIG_ETRAX_FAST_TIMER +@@ -586,11 +588,10 @@ + static void change_speed(struct e100_serial *info); + static void rs_throttle(struct tty_struct * tty); + static void rs_wait_until_sent(struct tty_struct *tty, int timeout); +-static int rs_write(struct tty_struct * tty, int from_user, ++static int rs_write(struct tty_struct * tty, + const unsigned char *buf, int count); + #ifdef CONFIG_ETRAX_RS485 +-static int e100_write_rs485(struct tty_struct * tty, int from_user, +- const unsigned char *buf, int count); ++static int e100_write_rs485(struct tty_struct * tty, const unsigned char *buf, int count); + #endif + static int get_lsr_info(struct e100_serial * info, unsigned int *value); + +@@ -677,20 +678,39 @@ + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 2, ++ .dma_owner = dma_ser0, ++ .io_if = if_serial_0, + #ifdef CONFIG_ETRAX_SERIAL_PORT0 + .enabled = 1, + #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT + .dma_out_enabled = 1, ++ .dma_out_nbr = SER0_TX_DMA_NBR, ++ .dma_out_irq_nbr = SER0_DMA_TX_IRQ_NBR, ++ .dma_out_irq_flags = IRQF_DISABLED, ++ .dma_out_irq_description = "serial 0 dma tr", + #else + .dma_out_enabled = 0, ++ .dma_out_nbr = UINT_MAX, ++ .dma_out_irq_nbr = 0, ++ .dma_out_irq_flags = 0, ++ .dma_out_irq_description = NULL, + #endif + #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN + .dma_in_enabled = 1, ++ .dma_in_nbr = SER0_RX_DMA_NBR, ++ .dma_in_irq_nbr = SER0_DMA_RX_IRQ_NBR, ++ .dma_in_irq_flags = IRQF_DISABLED, ++ .dma_in_irq_description = "serial 0 dma rec", + #else +- .dma_in_enabled = 0 ++ .dma_in_enabled = 0, ++ .dma_in_nbr = UINT_MAX, ++ .dma_in_irq_nbr = 0, ++ .dma_in_irq_flags = 0, ++ .dma_in_irq_description = NULL, + #endif + #else + .enabled = 0, ++ .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 + #endif +@@ -712,20 +732,42 @@ + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 3, ++ .dma_owner = dma_ser1, ++ .io_if = if_serial_1, + #ifdef CONFIG_ETRAX_SERIAL_PORT1 + .enabled = 1, ++ .io_if_description = "ser1", + #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT + .dma_out_enabled = 1, ++ .dma_out_nbr = SER1_TX_DMA_NBR, ++ .dma_out_irq_nbr = SER1_DMA_TX_IRQ_NBR, ++ .dma_out_irq_flags = IRQF_DISABLED, ++ .dma_out_irq_description = "serial 1 dma tr", + #else + .dma_out_enabled = 0, ++ .dma_out_nbr = UINT_MAX, ++ .dma_out_irq_nbr = 0, ++ .dma_out_irq_flags = 0, ++ .dma_out_irq_description = NULL, + #endif + #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN + .dma_in_enabled = 1, ++ .dma_in_nbr = SER1_RX_DMA_NBR, ++ .dma_in_irq_nbr = SER1_DMA_RX_IRQ_NBR, ++ .dma_in_irq_flags = IRQF_DISABLED, ++ .dma_in_irq_description = "serial 1 dma rec", + #else +- .dma_in_enabled = 0 ++ .dma_in_enabled = 0, ++ .dma_in_enabled = 0, ++ .dma_in_nbr = UINT_MAX, ++ .dma_in_irq_nbr = 0, ++ .dma_in_irq_flags = 0, ++ .dma_in_irq_description = NULL, + #endif + #else + .enabled = 0, ++ .io_if_description = NULL, ++ .dma_in_irq_nbr = 0, + .dma_out_enabled = 0, + .dma_in_enabled = 0 + #endif +@@ -746,20 +788,40 @@ + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 0, ++ .dma_owner = dma_ser2, ++ .io_if = if_serial_2, + #ifdef CONFIG_ETRAX_SERIAL_PORT2 + .enabled = 1, ++ .io_if_description = "ser2", + #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT + .dma_out_enabled = 1, ++ .dma_out_nbr = SER2_TX_DMA_NBR, ++ .dma_out_irq_nbr = SER2_DMA_TX_IRQ_NBR, ++ .dma_out_irq_flags = IRQF_DISABLED, ++ .dma_out_irq_description = "serial 2 dma tr", + #else + .dma_out_enabled = 0, ++ .dma_in_nbr = UINT_MAX, ++ .dma_in_irq_nbr = 0, ++ .dma_in_irq_flags = 0, ++ .dma_in_irq_description = NULL, + #endif + #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN + .dma_in_enabled = 1, ++ .dma_in_nbr = SER2_RX_DMA_NBR, ++ .dma_in_irq_nbr = SER2_DMA_RX_IRQ_NBR, ++ .dma_in_irq_flags = IRQF_DISABLED, ++ .dma_in_irq_description = "serial 2 dma rec", + #else +- .dma_in_enabled = 0 ++ .dma_in_enabled = 0, ++ .dma_in_nbr = UINT_MAX, ++ .dma_in_irq_nbr = 0, ++ .dma_in_irq_flags = 0, ++ .dma_in_irq_description = NULL, + #endif + #else + .enabled = 0, ++ .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 + #endif +@@ -780,20 +842,40 @@ + .rx_ctrl = DEF_RX, + .tx_ctrl = DEF_TX, + .iseteop = 1, ++ .dma_owner = dma_ser3, ++ .io_if = if_serial_3, + #ifdef CONFIG_ETRAX_SERIAL_PORT3 + .enabled = 1, ++ .io_if_description = "ser3", + #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT + .dma_out_enabled = 1, ++ .dma_out_nbr = SER3_TX_DMA_NBR, ++ .dma_out_irq_nbr = SER3_DMA_TX_IRQ_NBR, ++ .dma_out_irq_flags = IRQF_DISABLED, ++ .dma_out_irq_description = "serial 3 dma tr", + #else + .dma_out_enabled = 0, ++ .dma_out_nbr = UINT_MAX, ++ .dma_out_irq_nbr = 0, ++ .dma_out_irq_flags = 0, ++ .dma_out_irq_description = NULL, + #endif + #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN + .dma_in_enabled = 1, ++ .dma_in_nbr = SER3_RX_DMA_NBR, ++ .dma_in_irq_nbr = SER3_DMA_RX_IRQ_NBR, ++ .dma_in_irq_flags = IRQF_DISABLED, ++ .dma_in_irq_description = "serial 3 dma rec", + #else +- .dma_in_enabled = 0 ++ .dma_in_enabled = 0, ++ .dma_in_nbr = UINT_MAX, ++ .dma_in_irq_nbr = 0, ++ .dma_in_irq_flags = 0, ++ .dma_in_irq_description = NULL + #endif + #else + .enabled = 0, ++ .io_if_description = NULL, + .dma_out_enabled = 0, + .dma_in_enabled = 0 + #endif +@@ -1414,12 +1496,11 @@ + { + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + *e100_modem_pins[info->line].dtr_shadow &= ~mask; + *e100_modem_pins[info->line].dtr_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].dtr_port = *e100_modem_pins[info->line].dtr_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + #ifdef SERIAL_DEBUG_IO +@@ -1438,12 +1519,11 @@ + { + #ifndef CONFIG_SVINTO_SIM + unsigned long flags; +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + info->rx_ctrl &= ~E100_RTS_MASK; + info->rx_ctrl |= (set ? 0 : E100_RTS_MASK); /* RTS is active low */ + info->port[REG_REC_CTRL] = info->rx_ctrl; +- restore_flags(flags); ++ local_irq_restore(flags); + #ifdef SERIAL_DEBUG_IO + printk("ser%i rts %i\n", info->line, set); + #endif +@@ -1461,12 +1541,11 @@ + unsigned char mask = e100_modem_pins[info->line].ri_mask; + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + *e100_modem_pins[info->line].ri_shadow &= ~mask; + *e100_modem_pins[info->line].ri_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].ri_port = *e100_modem_pins[info->line].ri_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + #endif + } +@@ -1479,12 +1558,11 @@ + unsigned char mask = e100_modem_pins[info->line].cd_mask; + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + *e100_modem_pins[info->line].cd_shadow &= ~mask; + *e100_modem_pins[info->line].cd_shadow |= (set ? 0 : mask); + *e100_modem_pins[info->line].cd_port = *e100_modem_pins[info->line].cd_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + #endif + } +@@ -1558,8 +1636,7 @@ + /* Disable output DMA channel for the serial port in question + * ( set to something other then serialX) + */ +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "disable_txdma_channel %i\n", info->line)); + if (info->line == 0) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma6)) == +@@ -1587,7 +1664,7 @@ + } + } + *R_GEN_CONFIG = genconfig_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + +@@ -1595,8 +1672,7 @@ + { + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "enable_txdma_channel %i\n", info->line)); + /* Enable output DMA channel for the serial port in question */ + if (info->line == 0) { +@@ -1613,7 +1689,7 @@ + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma4, serial3); + } + *R_GEN_CONFIG = genconfig_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + static void e100_disable_rxdma_channel(struct e100_serial *info) +@@ -1623,8 +1699,7 @@ + /* Disable input DMA channel for the serial port in question + * ( set to something other then serialX) + */ +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + if (info->line == 0) { + if ((genconfig_shadow & IO_MASK(R_GEN_CONFIG, dma7)) == + IO_STATE(R_GEN_CONFIG, dma7, serial0)) { +@@ -1651,7 +1726,7 @@ + } + } + *R_GEN_CONFIG = genconfig_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + +@@ -1659,8 +1734,7 @@ + { + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + /* Enable input DMA channel for the serial port in question */ + if (info->line == 0) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, dma7); +@@ -1676,7 +1750,7 @@ + genconfig_shadow |= IO_STATE(R_GEN_CONFIG, dma5, serial3); + } + *R_GEN_CONFIG = genconfig_shadow; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + #ifdef SERIAL_HANDLE_EARLY_ERRORS +@@ -1783,7 +1857,7 @@ + } + + static int +-e100_write_rs485(struct tty_struct *tty, int from_user, ++e100_write_rs485(struct tty_struct *tty, + const unsigned char *buf, int count) + { + struct e100_serial * info = (struct e100_serial *)tty->driver_data; +@@ -1796,7 +1870,7 @@ + */ + info->rs485.enabled = 1; + /* rs_write now deals with RS485 if enabled */ +- count = rs_write(tty, from_user, buf, count); ++ count = rs_write(tty, buf, count); + info->rs485.enabled = old_enabled; + return count; + } +@@ -1834,7 +1908,7 @@ + unsigned long flags; + unsigned long xoff; + +- save_flags(flags); cli(); ++ local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "XOFF rs_stop xmit %i\n", + CIRC_CNT(info->xmit.head, + info->xmit.tail,SERIAL_XMIT_SIZE))); +@@ -1846,7 +1920,7 @@ + } + + *((unsigned long *)&info->port[REG_XOFF]) = xoff; +- restore_flags(flags); ++ local_irq_restore(flags); + } + } + +@@ -1858,7 +1932,7 @@ + unsigned long flags; + unsigned long xoff; + +- save_flags(flags); cli(); ++ local_irq_save(flags); + DFLOW(DEBUG_LOG(info->line, "XOFF rs_start xmit %i\n", + CIRC_CNT(info->xmit.head, + info->xmit.tail,SERIAL_XMIT_SIZE))); +@@ -1873,7 +1947,7 @@ + info->xmit.head != info->xmit.tail && info->xmit.buf) + e100_enable_serial_tx_ready_irq(info); + +- restore_flags(flags); ++ local_irq_restore(flags); + } + } + +@@ -2053,8 +2127,7 @@ + static void flush_timeout_function(unsigned long data); + #define START_FLUSH_FAST_TIMER_TIME(info, string, usec) {\ + unsigned long timer_flags; \ +- save_flags(timer_flags); \ +- cli(); \ ++ local_irq_save(timer_flags); \ + if (fast_timers[info->line].function == NULL) { \ + serial_fast_timer_started++; \ + TIMERD(DEBUG_LOG(info->line, "start_timer %i ", info->line)); \ +@@ -2068,7 +2141,7 @@ + else { \ + TIMERD(DEBUG_LOG(info->line, "timer %i already running\n", info->line)); \ + } \ +- restore_flags(timer_flags); \ ++ local_irq_restore(timer_flags); \ + } + #define START_FLUSH_FAST_TIMER(info, string) START_FLUSH_FAST_TIMER_TIME(info, string, info->flush_time_usec) + +@@ -2097,8 +2170,7 @@ + { + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + + if (!info->first_recv_buffer) + info->first_recv_buffer = buffer; +@@ -2111,7 +2183,7 @@ + if (info->recv_cnt > info->max_recv_cnt) + info->max_recv_cnt = info->recv_cnt; + +- restore_flags(flags); ++ local_irq_restore(flags); + } + + static int +@@ -2131,11 +2203,7 @@ + info->icount.rx++; + } else { + struct tty_struct *tty = info->tty; +- *tty->flip.char_buf_ptr = data; +- *tty->flip.flag_buf_ptr = flag; +- tty->flip.flag_buf_ptr++; +- tty->flip.char_buf_ptr++; +- tty->flip.count++; ++ tty_insert_flip_char(tty, data, flag); + info->icount.rx++; + } + +@@ -2320,7 +2388,6 @@ + */ + return; + #endif +- info->tty->flip.count = 0; + if (info->uses_dma_in) { + /* reset the input dma channel to be sure it works */ + +@@ -2482,70 +2549,21 @@ + { + struct tty_struct *tty; + struct etrax_recv_buffer *buffer; +- unsigned int length; + unsigned long flags; +- int max_flip_size; +- +- if (!info->first_recv_buffer) +- return; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); ++ tty = info->tty; + +- if (!(tty = info->tty)) { +- restore_flags(flags); ++ if (!tty) { ++ local_irq_restore(flags); + return; + } + +- length = tty->flip.count; +- /* Don't flip more than the ldisc has room for. +- * The return value from ldisc.receive_room(tty) - might not be up to +- * date, the previous flip of up to TTY_FLIPBUF_SIZE might be on the +- * processed and not accounted for yet. +- * Since we use DMA, 1 SERIAL_DESCR_BUF_SIZE could be on the way. +- * Lets buffer data here and let flow control take care of it. +- * Since we normally flip large chunks, the ldisc don't react +- * with throttle until too late if we flip to much. +- */ +- max_flip_size = tty->ldisc.receive_room(tty); +- if (max_flip_size < 0) +- max_flip_size = 0; +- if (max_flip_size <= (TTY_FLIPBUF_SIZE + /* Maybe not accounted for */ +- length + info->recv_cnt + /* We have this queued */ +- 2*SERIAL_DESCR_BUF_SIZE + /* This could be on the way */ +- TTY_THRESHOLD_THROTTLE)) { /* Some slack */ +- /* check TTY_THROTTLED first so it indicates our state */ +- if (!test_and_set_bit(TTY_THROTTLED, &tty->flags)) { +- DFLOW(DEBUG_LOG(info->line,"flush_to_flip throttles room %lu\n", max_flip_size)); +- rs_throttle(tty); +- } +-#if 0 +- else if (max_flip_size <= (TTY_FLIPBUF_SIZE + /* Maybe not accounted for */ +- length + info->recv_cnt + /* We have this queued */ +- SERIAL_DESCR_BUF_SIZE + /* This could be on the way */ +- TTY_THRESHOLD_THROTTLE)) { /* Some slack */ +- DFLOW(DEBUG_LOG(info->line,"flush_to_flip throttles again! %lu\n", max_flip_size)); +- rs_throttle(tty); +- } +-#endif +- } +- +- if (max_flip_size > TTY_FLIPBUF_SIZE) +- max_flip_size = TTY_FLIPBUF_SIZE; +- +- while ((buffer = info->first_recv_buffer) && length < max_flip_size) { ++ while ((buffer = info->first_recv_buffer)) { + unsigned int count = buffer->length; + +- if (length + count > max_flip_size) +- count = max_flip_size - length; +- +- memcpy(tty->flip.char_buf_ptr + length, buffer->buffer, count); +- memset(tty->flip.flag_buf_ptr + length, TTY_NORMAL, count); +- tty->flip.flag_buf_ptr[length] = buffer->error; +- +- length += count; ++ tty_insert_flip_string(tty, buffer->buffer, count); + info->recv_cnt -= count; +- DFLIP(DEBUG_LOG(info->line,"flip: %i\n", length)); + + if (count == buffer->length) { + info->first_recv_buffer = buffer->next; +@@ -2560,24 +2578,7 @@ + if (!info->first_recv_buffer) + info->last_recv_buffer = NULL; + +- tty->flip.count = length; +- DFLIP(if (tty->ldisc.chars_in_buffer(tty) > 3500) { +- DEBUG_LOG(info->line, "ldisc %lu\n", +- tty->ldisc.chars_in_buffer(tty)); +- DEBUG_LOG(info->line, "flip.count %lu\n", +- tty->flip.count); +- } +- ); +- restore_flags(flags); +- +- DFLIP( +- if (1) { +- DEBUG_LOG(info->line, "*** rxtot %i\n", info->icount.rx); +- DEBUG_LOG(info->line, "ldisc %lu\n", tty->ldisc.chars_in_buffer(tty)); +- DEBUG_LOG(info->line, "room %lu\n", tty->ldisc.receive_room(tty)); +- } +- +- ); ++ local_irq_restore(flags); + + /* this includes a check for low-latency */ + tty_flip_buffer_push(tty); +@@ -2722,21 +2723,7 @@ + printk("!NO TTY!\n"); + return info; + } +- if (tty->flip.count >= TTY_FLIPBUF_SIZE - TTY_THRESHOLD_THROTTLE) { +- /* check TTY_THROTTLED first so it indicates our state */ +- if (!test_and_set_bit(TTY_THROTTLED, &tty->flags)) { +- DFLOW(DEBUG_LOG(info->line, "rs_throttle flip.count: %i\n", tty->flip.count)); +- rs_throttle(tty); +- } +- } +- if (tty->flip.count >= TTY_FLIPBUF_SIZE) { +- DEBUG_LOG(info->line, "force FLIP! %i\n", tty->flip.count); +- tty->flip.work.func((void *) tty); +- if (tty->flip.count >= TTY_FLIPBUF_SIZE) { +- DEBUG_LOG(info->line, "FLIP FULL! %i\n", tty->flip.count); +- return info; /* if TTY_DONT_FLIP is set */ +- } +- } ++ + /* Read data and status at the same time */ + data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]); + more_data: +@@ -2789,27 +2776,25 @@ + DEBUG_LOG(info->line, "EBRK %i\n", info->break_detected_cnt); + info->errorcode = ERRCODE_INSERT_BREAK; + } else { ++ unsigned char data = IO_EXTRACT(R_SERIAL0_READ, data_in, data_read); ++ char flag = TTY_NORMAL; + if (info->errorcode == ERRCODE_INSERT_BREAK) { +- info->icount.brk++; +- *tty->flip.char_buf_ptr = 0; +- *tty->flip.flag_buf_ptr = TTY_BREAK; +- tty->flip.flag_buf_ptr++; +- tty->flip.char_buf_ptr++; +- tty->flip.count++; ++ struct tty_struct *tty = info->tty; ++ tty_insert_flip_char(tty, 0, flag); + info->icount.rx++; + } +- *tty->flip.char_buf_ptr = IO_EXTRACT(R_SERIAL0_READ, data_in, data_read); + + if (data_read & IO_MASK(R_SERIAL0_READ, par_err)) { + info->icount.parity++; +- *tty->flip.flag_buf_ptr = TTY_PARITY; ++ flag = TTY_PARITY; + } else if (data_read & IO_MASK(R_SERIAL0_READ, overrun)) { + info->icount.overrun++; +- *tty->flip.flag_buf_ptr = TTY_OVERRUN; ++ flag = TTY_OVERRUN; + } else if (data_read & IO_MASK(R_SERIAL0_READ, framing_err)) { + info->icount.frame++; +- *tty->flip.flag_buf_ptr = TTY_FRAME; ++ flag = TTY_FRAME; + } ++ tty_insert_flip_char(tty, data, flag); + info->errorcode = 0; + } + info->break_detected_cnt = 0; +@@ -2825,16 +2810,12 @@ + log_int(rdpc(), 0, 0); + } + ); +- *tty->flip.char_buf_ptr = IO_EXTRACT(R_SERIAL0_READ, data_in, data_read); +- *tty->flip.flag_buf_ptr = 0; ++ tty_insert_flip_char(tty, IO_EXTRACT(R_SERIAL0_READ, data_in, data_read), TTY_NORMAL); + } else { + DEBUG_LOG(info->line, "ser_rx int but no data_avail %08lX\n", data_read); + } + + +- tty->flip.flag_buf_ptr++; +- tty->flip.char_buf_ptr++; +- tty->flip.count++; + info->icount.rx++; + data_read = *((unsigned long *)&info->port[REG_DATA_STATUS32]); + if (data_read & IO_MASK(R_SERIAL0_READ, data_avail)) { +@@ -2972,7 +2953,7 @@ + if (info->x_char) { + unsigned char rstat; + DFLOW(DEBUG_LOG(info->line, "tx_int: xchar 0x%02X\n", info->x_char)); +- save_flags(flags); cli(); ++ local_irq_save(flags); + rstat = info->port[REG_STATUS]; + DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); + +@@ -2981,7 +2962,7 @@ + info->x_char = 0; + /* We must enable since it is disabled in ser_interrupt */ + e100_enable_serial_tx_ready_irq(info); +- restore_flags(flags); ++ local_irq_restore(flags); + return; + } + if (info->uses_dma_out) { +@@ -2989,7 +2970,7 @@ + int i; + /* We only use normal tx interrupt when sending x_char */ + DFLOW(DEBUG_LOG(info->line, "tx_int: xchar sent\n", 0)); +- save_flags(flags); cli(); ++ local_irq_save(flags); + rstat = info->port[REG_STATUS]; + DFLOW(DEBUG_LOG(info->line, "stat %x\n", rstat)); + e100_disable_serial_tx_ready_irq(info); +@@ -3002,7 +2983,7 @@ + nop(); + + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, continue); +- restore_flags(flags); ++ local_irq_restore(flags); + return; + } + /* Normal char-by-char interrupt */ +@@ -3016,7 +2997,7 @@ + } + DINTR2(DEBUG_LOG(info->line, "tx_int %c\n", info->xmit.buf[info->xmit.tail])); + /* Send a byte, rs485 timing is critical so turn of ints */ +- save_flags(flags); cli(); ++ local_irq_save(flags); + info->port[REG_TR_DATA] = info->xmit.buf[info->xmit.tail]; + info->xmit.tail = (info->xmit.tail + 1) & (SERIAL_XMIT_SIZE-1); + info->icount.tx++; +@@ -3040,7 +3021,7 @@ + /* We must enable since it is disabled in ser_interrupt */ + e100_enable_serial_tx_ready_irq(info); + } +- restore_flags(flags); ++ local_irq_restore(flags); + + if (CIRC_CNT(info->xmit.head, + info->xmit.tail, +@@ -3065,7 +3046,7 @@ + int handled = 0; + static volatile unsigned long reentered_ready_mask = 0; + +- save_flags(flags); cli(); ++ local_irq_save(flags); + irq_mask1_rd = *R_IRQ_MASK1_RD; + /* First handle all rx interrupts with ints disabled */ + info = rs_table; +@@ -3110,7 +3091,7 @@ + /* Unblock the serial interrupt */ + *R_VECT_MASK_SET = IO_STATE(R_VECT_MASK_SET, serial, set); + +- sti(); ++ local_irq_enable(); + ready_mask = (1 << (8+1+2*0)); /* ser0 tr_ready */ + info = rs_table; + for (i = 0; i < NR_PORTS; i++) { +@@ -3123,11 +3104,11 @@ + ready_mask <<= 2; + } + /* handle_ser_tx_interrupt enables tr_ready interrupts */ +- cli(); ++ local_irq_disable(); + /* Handle reentered TX interrupt */ + irq_mask1_rd = reentered_ready_mask; + } +- cli(); ++ local_irq_disable(); + tx_started = 0; + } else { + unsigned long ready_mask; +@@ -3143,7 +3124,7 @@ + } + } + +- restore_flags(flags); ++ local_irq_restore(flags); + return IRQ_RETVAL(handled); + } /* ser_interrupt */ + #endif +@@ -3192,13 +3173,12 @@ + if (!xmit_page) + return -ENOMEM; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + + /* if it was already initialized, skip this */ + + if (info->flags & ASYNC_INITIALIZED) { +- restore_flags(flags); ++ local_irq_restore(flags); + free_page(xmit_page); + return 0; + } +@@ -3324,7 +3304,7 @@ + + info->flags |= ASYNC_INITIALIZED; + +- restore_flags(flags); ++ local_irq_restore(flags); + return 0; + } + +@@ -3375,8 +3355,7 @@ + info->irq); + #endif + +- save_flags(flags); +- cli(); /* Disable interrupts */ ++ local_irq_save(flags); + + if (info->xmit.buf) { + free_page((unsigned long)info->xmit.buf); +@@ -3400,7 +3379,7 @@ + set_bit(TTY_IO_ERROR, &info->tty->flags); + + info->flags &= ~ASYNC_INITIALIZED; +- restore_flags(flags); ++ local_irq_restore(flags); + } + + +@@ -3492,8 +3471,7 @@ + + #ifndef CONFIG_SVINTO_SIM + /* start with default settings and then fill in changes */ +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + /* 8 bit, no/even parity */ + info->rx_ctrl &= ~(IO_MASK(R_SERIAL0_REC_CTRL, rec_bitnr) | + IO_MASK(R_SERIAL0_REC_CTRL, rec_par_en) | +@@ -3557,7 +3535,7 @@ + } + + *((unsigned long *)&info->port[REG_XOFF]) = xoff; +- restore_flags(flags); ++ local_irq_restore(flags); + #endif /* !CONFIG_SVINTO_SIM */ + + update_char_time(info); +@@ -3585,13 +3563,12 @@ + + /* this protection might not exactly be necessary here */ + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + start_transmit(info); +- restore_flags(flags); ++ local_irq_restore(flags); + } + +-static int rs_raw_write(struct tty_struct * tty, int from_user, ++static int rs_raw_write(struct tty_struct * tty, + const unsigned char *buf, int count) + { + int c, ret = 0; +@@ -3614,72 +3591,37 @@ + SIMCOUT(buf, count); + return count; + #endif +- save_flags(flags); ++ local_save_flags(flags); + DFLOW(DEBUG_LOG(info->line, "write count %i ", count)); + DFLOW(DEBUG_LOG(info->line, "ldisc %i\n", tty->ldisc.chars_in_buffer(tty))); + + +- /* the cli/restore_flags pairs below are needed because the ++ /* the local_irq_disable/restore_flags pairs below are needed because the + * DMA interrupt handler moves the info->xmit values. the memcpy + * needs to be in the critical region unfortunately, because we + * need to read xmit values, memcpy, write xmit values in one + * atomic operation... this could perhaps be avoided by more clever + * design. + */ +- if (from_user) { +- mutex_lock(&tmp_buf_mutex); +- while (1) { +- int c1; +- c = CIRC_SPACE_TO_END(info->xmit.head, +- info->xmit.tail, +- SERIAL_XMIT_SIZE); +- if (count < c) +- c = count; +- if (c <= 0) +- break; +- +- c -= copy_from_user(tmp_buf, buf, c); +- if (!c) { +- if (!ret) +- ret = -EFAULT; +- break; +- } +- cli(); +- c1 = CIRC_SPACE_TO_END(info->xmit.head, +- info->xmit.tail, +- SERIAL_XMIT_SIZE); +- if (c1 < c) +- c = c1; +- memcpy(info->xmit.buf + info->xmit.head, tmp_buf, c); +- info->xmit.head = ((info->xmit.head + c) & +- (SERIAL_XMIT_SIZE-1)); +- restore_flags(flags); +- buf += c; +- count -= c; +- ret += c; +- } +- mutex_unlock(&tmp_buf_mutex); +- } else { +- cli(); +- while (count) { +- c = CIRC_SPACE_TO_END(info->xmit.head, +- info->xmit.tail, +- SERIAL_XMIT_SIZE); +- +- if (count < c) +- c = count; +- if (c <= 0) +- break; +- +- memcpy(info->xmit.buf + info->xmit.head, buf, c); +- info->xmit.head = (info->xmit.head + c) & +- (SERIAL_XMIT_SIZE-1); +- buf += c; +- count -= c; +- ret += c; +- } +- restore_flags(flags); ++ local_irq_disable(); ++ while (count) { ++ c = CIRC_SPACE_TO_END(info->xmit.head, ++ info->xmit.tail, ++ SERIAL_XMIT_SIZE); ++ ++ if (count < c) ++ c = count; ++ if (c <= 0) ++ break; ++ ++ memcpy(info->xmit.buf + info->xmit.head, buf, c); ++ info->xmit.head = (info->xmit.head + c) & ++ (SERIAL_XMIT_SIZE-1); ++ buf += c; ++ count -= c; ++ ret += c; + } ++ local_irq_restore(flags); + + /* enable transmitter if not running, unless the tty is stopped + * this does not need IRQ protection since if tr_running == 0 +@@ -3698,7 +3640,7 @@ + } /* raw_raw_write() */ + + static int +-rs_write(struct tty_struct * tty, int from_user, ++rs_write(struct tty_struct * tty, + const unsigned char *buf, int count) + { + #if defined(CONFIG_ETRAX_RS485) +@@ -3725,7 +3667,7 @@ + } + #endif /* CONFIG_ETRAX_RS485 */ + +- count = rs_raw_write(tty, from_user, buf, count); ++ count = rs_raw_write(tty, buf, count); + + #if defined(CONFIG_ETRAX_RS485) + if (info->rs485.enabled) +@@ -3793,10 +3735,9 @@ + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + info->xmit.head = info->xmit.tail = 0; +- restore_flags(flags); ++ local_irq_restore(flags); + + wake_up_interruptible(&tty->write_wait); + +@@ -3818,7 +3759,7 @@ + { + struct e100_serial *info = (struct e100_serial *)tty->driver_data; + unsigned long flags; +- save_flags(flags); cli(); ++ local_irq_save(flags); + if (info->uses_dma_out) { + /* Put the DMA on hold and disable the channel */ + *info->ocmdadr = IO_STATE(R_DMA_CH6_CMD, cmd, hold); +@@ -3835,7 +3776,7 @@ + DFLOW(DEBUG_LOG(info->line, "rs_send_xchar 0x%02X\n", ch)); + info->x_char = ch; + e100_enable_serial_tx_ready_irq(info); +- restore_flags(flags); ++ local_irq_restore(flags); + } + + /* +@@ -4085,61 +4026,6 @@ + return 0; + } + +- +-static int +-set_modem_info(struct e100_serial * info, unsigned int cmd, +- unsigned int *value) +-{ +- unsigned int arg; +- +- if (copy_from_user(&arg, value, sizeof(int))) +- return -EFAULT; +- +- switch (cmd) { +- case TIOCMBIS: +- if (arg & TIOCM_RTS) { +- e100_rts(info, 1); +- } +- if (arg & TIOCM_DTR) { +- e100_dtr(info, 1); +- } +- /* Handle FEMALE behaviour */ +- if (arg & TIOCM_RI) { +- e100_ri_out(info, 1); +- } +- if (arg & TIOCM_CD) { +- e100_cd_out(info, 1); +- } +- break; +- case TIOCMBIC: +- if (arg & TIOCM_RTS) { +- e100_rts(info, 0); +- } +- if (arg & TIOCM_DTR) { +- e100_dtr(info, 0); +- } +- /* Handle FEMALE behaviour */ +- if (arg & TIOCM_RI) { +- e100_ri_out(info, 0); +- } +- if (arg & TIOCM_CD) { +- e100_cd_out(info, 0); +- } +- break; +- case TIOCMSET: +- e100_rts(info, arg & TIOCM_RTS); +- e100_dtr(info, arg & TIOCM_DTR); +- /* Handle FEMALE behaviour */ +- e100_ri_out(info, arg & TIOCM_RI); +- e100_cd_out(info, arg & TIOCM_CD); +- break; +- default: +- return -EINVAL; +- } +- return 0; +-} +- +- + static void + rs_break(struct tty_struct *tty, int break_state) + { +@@ -4149,8 +4035,7 @@ + if (!info->port) + return; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + if (break_state == -1) { + /* Go to manual mode and set the txd pin to 0 */ + info->tx_ctrl &= 0x3F; /* Clear bit 7 (txd) and 6 (tr_enable) */ +@@ -4158,7 +4043,42 @@ + info->tx_ctrl |= (0x80 | 0x40); /* Set bit 7 (txd) and 6 (tr_enable) */ + } + info->port[REG_TR_CTRL] = info->tx_ctrl; +- restore_flags(flags); ++ local_irq_restore(flags); ++} ++ ++static int ++rs_tiocmset(struct tty_struct *tty, struct file * file, unsigned int set, unsigned int clear) ++{ ++ struct e100_serial * info = (struct e100_serial *)tty->driver_data; ++ ++ if (clear & TIOCM_RTS) { ++ e100_rts(info, 0); ++ } ++ if (clear & TIOCM_DTR) { ++ e100_dtr(info, 0); ++ } ++ /* Handle FEMALE behaviour */ ++ if (clear & TIOCM_RI) { ++ e100_ri_out(info, 0); ++ } ++ if (clear & TIOCM_CD) { ++ e100_cd_out(info, 0); ++ } ++ ++ if (set & TIOCM_RTS) { ++ e100_rts(info, 1); ++ } ++ if (set & TIOCM_DTR) { ++ e100_dtr(info, 1); ++ } ++ /* Handle FEMALE behaviour */ ++ if (set & TIOCM_RI) { ++ e100_ri_out(info, 1); ++ } ++ if (set & TIOCM_CD) { ++ e100_cd_out(info, 1); ++ } ++ return 0; + } + + static int +@@ -4177,10 +4097,6 @@ + switch (cmd) { + case TIOCMGET: + return get_modem_info(info, (unsigned int *) arg); +- case TIOCMBIS: +- case TIOCMBIC: +- case TIOCMSET: +- return set_modem_info(info, cmd, (unsigned int *) arg); + case TIOCGSERIAL: + return get_serial_info(info, + (struct serial_struct *) arg); +@@ -4212,7 +4128,7 @@ + if (copy_from_user(&rs485wr, (struct rs485_write*)arg, sizeof(rs485wr))) + return -EFAULT; + +- return e100_write_rs485(tty, 1, rs485wr.outc, rs485wr.outc_size); ++ return e100_write_rs485(tty, rs485wr.outc, rs485wr.outc_size); + } + #endif + +@@ -4242,46 +4158,6 @@ + + } + +-/* In debugport.c - register a console write function that uses the normal +- * serial driver +- */ +-typedef int (*debugport_write_function)(int i, const char *buf, unsigned int len); +- +-extern debugport_write_function debug_write_function; +- +-static int rs_debug_write_function(int i, const char *buf, unsigned int len) +-{ +- int cnt; +- int written = 0; +- struct tty_struct *tty; +- static int recurse_cnt = 0; +- +- tty = rs_table[i].tty; +- if (tty) { +- unsigned long flags; +- if (recurse_cnt > 5) /* We skip this debug output */ +- return 1; +- +- local_irq_save(flags); +- recurse_cnt++; +- local_irq_restore(flags); +- do { +- cnt = rs_write(tty, 0, buf + written, len); +- if (cnt >= 0) { +- written += cnt; +- buf += cnt; +- len -= cnt; +- } else +- len = cnt; +- } while(len > 0); +- local_irq_save(flags); +- recurse_cnt--; +- local_irq_restore(flags); +- return 1; +- } +- return 0; +-} +- + /* + * ------------------------------------------------------------ + * rs_close() +@@ -4303,11 +4179,10 @@ + + /* interrupts are disabled for this entire function */ + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + + if (tty_hung_up_p(filp)) { +- restore_flags(flags); ++ local_irq_restore(flags); + return; + } + +@@ -4334,7 +4209,7 @@ + info->count = 0; + } + if (info->count) { +- restore_flags(flags); ++ local_irq_restore(flags); + return; + } + info->flags |= ASYNC_CLOSING; +@@ -4388,7 +4263,7 @@ + } + info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING); + wake_up_interruptible(&info->close_wait); +- restore_flags(flags); ++ local_irq_restore(flags); + + /* port closed */ + +@@ -4410,6 +4285,28 @@ + #endif + } + #endif ++ ++ /* ++ * Release any allocated DMA irq's. ++ */ ++ if (info->dma_in_enabled) { ++ cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description); ++ free_irq(info->dma_in_irq_nbr, ++ info); ++ info->uses_dma_in = 0; ++#ifdef SERIAL_DEBUG_OPEN ++ printk("DMA irq '%s' freed\n", info->dma_in_irq_description); ++#endif ++ } ++ if (info->dma_out_enabled) { ++ free_irq(info->dma_out_irq_nbr, ++ info); ++ cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description); ++ info->uses_dma_out = 0; ++#ifdef SERIAL_DEBUG_OPEN ++ printk("DMA irq '%s' freed\n", info->dma_out_irq_description); ++#endif ++ } + } + + /* +@@ -4485,7 +4382,7 @@ + if (tty_hung_up_p(filp) || + (info->flags & ASYNC_CLOSING)) { + if (info->flags & ASYNC_CLOSING) +- interruptible_sleep_on(&info->close_wait); ++ wait_event_interruptible(info->close_wait, 0); + #ifdef SERIAL_DO_RESTART + if (info->flags & ASYNC_HUP_NOTIFY) + return -EAGAIN; +@@ -4523,21 +4420,19 @@ + printk("block_til_ready before block: ttyS%d, count = %d\n", + info->line, info->count); + #endif +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + if (!tty_hung_up_p(filp)) { + extra_count++; + info->count--; + } +- restore_flags(flags); ++ local_irq_restore(flags); + info->blocked_open++; + while (1) { +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + /* assert RTS and DTR */ + e100_rts(info, 1); + e100_dtr(info, 1); +- restore_flags(flags); ++ local_irq_restore(flags); + set_current_state(TASK_INTERRUPTIBLE); + if (tty_hung_up_p(filp) || + !(info->flags & ASYNC_INITIALIZED)) { +@@ -4589,9 +4484,9 @@ + struct e100_serial *info; + int retval, line; + unsigned long page; ++ int allocated_resources = 0; + + /* find which port we want to open */ +- + line = tty->index; + + if (line < 0 || line >= NR_PORTS) +@@ -4632,7 +4527,7 @@ + if (tty_hung_up_p(filp) || + (info->flags & ASYNC_CLOSING)) { + if (info->flags & ASYNC_CLOSING) +- interruptible_sleep_on(&info->close_wait); ++ wait_event_interruptible(info->close_wait, 0); + #ifdef SERIAL_DO_RESTART + return ((info->flags & ASYNC_HUP_NOTIFY) ? + -EAGAIN : -ERESTARTSYS); +@@ -4642,12 +4537,79 @@ + } + + /* ++ * If DMA is enabled try to allocate the irq's. ++ */ ++ if (info->count == 1) { ++ allocated_resources = 1; ++ if (info->dma_in_enabled) { ++ if (request_irq(info->dma_in_irq_nbr, ++ rec_interrupt, ++ info->dma_in_irq_flags, ++ info->dma_in_irq_description, ++ info)) { ++ printk(KERN_WARNING "DMA irq '%s' busy; falling back to non-DMA mode\n", info->dma_in_irq_description); ++ /* Make sure we never try to use DMA in for the port again. */ ++ info->dma_in_enabled = 0; ++ } else if (cris_request_dma(info->dma_in_nbr, ++ info->dma_in_irq_description, ++ DMA_VERBOSE_ON_ERROR, ++ info->dma_owner)) { ++ free_irq(info->dma_in_irq_nbr, info); ++ printk(KERN_WARNING "DMA '%s' busy; falling back to non-DMA mode\n", info->dma_in_irq_description); ++ /* Make sure we never try to use DMA in for the port again. */ ++ info->dma_in_enabled = 0; ++ } ++#ifdef SERIAL_DEBUG_OPEN ++ else printk("DMA irq '%s' allocated\n", info->dma_in_irq_description); ++#endif ++ } ++ if (info->dma_out_enabled) { ++ if (request_irq(info->dma_out_irq_nbr, ++ tr_interrupt, ++ info->dma_out_irq_flags, ++ info->dma_out_irq_description, ++ info)) { ++ printk(KERN_WARNING "DMA irq '%s' busy; falling back to non-DMA mode\n", info->dma_out_irq_description); ++ /* Make sure we never try to use DMA out for the port again. */ ++ info->dma_out_enabled = 0; ++ } else if (cris_request_dma(info->dma_out_nbr, ++ info->dma_out_irq_description, ++ DMA_VERBOSE_ON_ERROR, ++ info->dma_owner)) { ++ free_irq(info->dma_out_irq_nbr, info); ++ printk(KERN_WARNING "DMA '%s' busy; falling back to non-DMA mode\n", info->dma_out_irq_description); ++ /* Make sure we never try to use DMA in for the port again. */ ++ info->dma_out_enabled = 0; ++ } ++#ifdef SERIAL_DEBUG_OPEN ++ else printk("DMA irq '%s' allocated\n", info->dma_out_irq_description); ++#endif ++ } ++ } ++ ++ /* + * Start up the serial port + */ + + retval = startup(info); +- if (retval) +- return retval; ++ if (retval) { ++ if (allocated_resources) { ++ if (info->dma_out_enabled) { ++ cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description); ++ free_irq(info->dma_out_irq_nbr, ++ info); ++ } ++ if (info->dma_in_enabled) { ++ cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description); ++ free_irq(info->dma_in_irq_nbr, ++ info); ++ } ++ } ++ /* FIXME Decrease count info->count here too? */ ++ return retval; ++ ++ } ++ + + retval = block_til_ready(tty, filp, info); + if (retval) { +@@ -4655,6 +4617,19 @@ + printk("rs_open returning after block_til_ready with %d\n", + retval); + #endif ++ if (allocated_resources) { ++ if (info->dma_out_enabled) { ++ cris_free_dma(info->dma_out_nbr, info->dma_out_irq_description); ++ free_irq(info->dma_out_irq_nbr, ++ info); ++ } ++ if (info->dma_in_enabled) { ++ cris_free_dma(info->dma_in_nbr, info->dma_in_irq_description); ++ free_irq(info->dma_in_irq_nbr, ++ info); ++ } ++ } ++ + return retval; + } + +@@ -4844,6 +4819,7 @@ + .send_xchar = rs_send_xchar, + .wait_until_sent = rs_wait_until_sent, + .read_proc = rs_read_proc, ++ .tiocmset = rs_tiocmset + }; + + static int __init +@@ -4863,7 +4839,22 @@ + #if !defined(CONFIG_ETRAX_SERIAL_FAST_TIMER) + init_timer(&flush_timer); + flush_timer.function = timed_flush_handler; +- mod_timer(&flush_timer, jiffies + CONFIG_ETRAX_SERIAL_RX_TIMEOUT_TICKS); ++ mod_timer(&flush_timer, jiffies + 5); ++#endif ++ ++#if defined(CONFIG_ETRAX_RS485) ++#if defined(CONFIG_ETRAX_RS485_ON_PA) ++ if (cris_io_interface_allocate_pins(if_ser0, 'a', rs485_pa_bit, rs485_pa_bit)) { ++ printk(KERN_CRIT "ETRAX100LX serial: Could not allocate RS485 pin\n"); ++ return -EBUSY; ++ } ++#endif ++#if defined(CONFIG_ETRAX_RS485_ON_PORT_G) ++ if (cris_io_interface_allocate_pins(if_ser0, 'g', rs485_pa_bit, rs485_port_g_bit)) { ++ printk(KERN_CRIT "ETRAX100LX serial: Could not allocate RS485 pin\n"); ++ return -EBUSY; ++ } ++#endif + #endif + + /* Initialize the tty_driver structure */ +@@ -4888,6 +4879,14 @@ + /* do some initializing for the separate ports */ + + for (i = 0, info = rs_table; i < NR_PORTS; i++,info++) { ++ if (info->enabled) { ++ if (cris_request_io_interface(info->io_if, info->io_if_description)) { ++ printk(KERN_CRIT "ETRAX100LX async serial: Could not allocate IO pins for %s, port %d\n", ++ info->io_if_description, ++ i); ++ info->enabled = 0; ++ } ++ } + info->uses_dma_in = 0; + info->uses_dma_out = 0; + info->line = i; +@@ -4939,64 +4938,16 @@ + #endif + + #ifndef CONFIG_SVINTO_SIM ++#ifndef CONFIG_ETRAX_KGDB + /* Not needed in simulator. May only complicate stuff. */ + /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */ + +- if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", NULL)) +- panic("irq8"); +- +-#ifdef CONFIG_ETRAX_SERIAL_PORT0 +-#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT +- if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 0 dma tr", NULL)) +- panic("irq22"); +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN +- if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 0 dma rec", NULL)) +- panic("irq23"); +-#endif +-#endif +- +-#ifdef CONFIG_ETRAX_SERIAL_PORT1 +-#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT +- if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 1 dma tr", NULL)) +- panic("irq24"); +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN +- if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 1 dma rec", NULL)) +- panic("irq25"); +-#endif +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT2 +- /* DMA Shared with par0 (and SCSI0 and ATA) */ +-#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT +- if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma tr", NULL)) +- panic("irq18"); +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN +- if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma rec", NULL)) +- panic("irq19"); +-#endif +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT3 +- /* DMA Shared with par1 (and SCSI1 and Extern DMA 0) */ +-#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT +- if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma tr", NULL)) +- panic("irq20"); +-#endif +-#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN +- if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma rec", NULL)) +- panic("irq21"); +-#endif +-#endif ++ if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", driver)) ++ panic("%s: Failed to request irq8", __FUNCTION__); + +-#ifdef CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST +- if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, IRQF_SHARED | IRQF_DISABLED, +- "fast serial dma timeout", NULL)) { +- printk(KERN_CRIT "err: timer1 irq\n"); +- } + #endif + #endif /* CONFIG_SVINTO_SIM */ +- debug_write_function = rs_debug_write_function; ++ + return 0; + } + +--- linux-2.6.19.2.orig/drivers/serial/crisv10.h 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/serial/crisv10.h 2006-10-13 14:44:38.000000000 +0200 +@@ -9,6 +9,8 @@ + + #include <linux/circ_buf.h> + #include <asm/termios.h> ++#include <asm/dma.h> ++#include <asm/arch/io_interface_mux.h> + + /* Software state per channel */ + +@@ -61,6 +63,19 @@ + u8 dma_in_enabled:1; /* Set to 1 if DMA should be used */ + + /* end of fields defined in rs_table[] in .c-file */ ++ int dma_owner; ++ unsigned int dma_in_nbr; ++ unsigned int dma_out_nbr; ++ unsigned int dma_in_irq_nbr; ++ unsigned int dma_out_irq_nbr; ++ unsigned long dma_in_irq_flags; ++ unsigned long dma_out_irq_flags; ++ char *dma_in_irq_description; ++ char *dma_out_irq_description; ++ ++ enum cris_io_interface io_if; ++ char *io_if_description; ++ + u8 uses_dma_in; /* Set to 1 if DMA is used */ + u8 uses_dma_out; /* Set to 1 if DMA is used */ + u8 forced_eop; /* a fifo eop has been forced */ +--- linux-2.6.19.2.orig/drivers/serial/crisv32.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/serial/crisv32.c 2007-01-05 09:59:53.000000000 +0100 +@@ -0,0 +1,2333 @@ ++/* $Id: crisv32.c,v 1.78 2007/01/05 08:59:53 starvik Exp $ ++ * ++ * Serial port driver for the ETRAX FS chip ++ * ++ * Copyright (C) 1998-2006 Axis Communications AB ++ * ++ * Many, many authors. Based once upon a time on serial.c for 16x50. ++ * ++ * Johan Adolfsson - port to ETRAX FS ++ * Mikael Starvik - port to serial_core framework ++ * ++ */ ++ ++#include <linux/module.h> ++#include <linux/init.h> ++#include <linux/console.h> ++#include <linux/types.h> ++#include <linux/errno.h> ++#include <linux/serial_core.h> ++ ++#include <asm/io.h> ++#include <asm/irq.h> ++#include <asm/system.h> ++#include <asm/uaccess.h> ++ ++#include <asm/arch/dma.h> ++#include <asm/arch/system.h> ++#include <asm/arch/pinmux.h> ++#include <asm/arch/hwregs/dma.h> ++#include <asm/arch/hwregs/reg_rdwr.h> ++#include <asm/arch/hwregs/ser_defs.h> ++#include <asm/arch/hwregs/dma_defs.h> ++#include <asm/arch/hwregs/gio_defs.h> ++#include <asm/arch/hwregs/intr_vect_defs.h> ++#include <asm/arch/hwregs/reg_map.h> ++ ++#define UART_NR 5 /* 4 ports + dummy port */ ++#define SERIAL_RECV_DESCRIPTORS 8 ++ ++/* We only buffer 255 characters here, no need for more tx descriptors. */ ++#define SERIAL_TX_DESCRIPTORS 4 ++ ++/* Kept for experimental purposes. */ ++#define ETRAX_SER_FIFO_SIZE 1 ++#define SERIAL_DESCR_BUF_SIZE 256 ++#define regi_NULL 0 ++#define DMA_WAIT_UNTIL_RESET(inst) \ ++ do { \ ++ reg_dma_rw_stat r; \ ++ do { \ ++ r = REG_RD(dma, (inst), rw_stat); \ ++ } while (r.mode != regk_dma_rst); \ ++ } while (0) ++ ++/* Macro to set up control lines for a port. */ ++#define SETUP_PINS(port) \ ++ if (serial_cris_ports[port].used) { \ ++ if (strcmp(CONFIG_ETRAX_SER##port##_DTR_BIT, "")) \ ++ crisv32_io_get_name(&serial_cris_ports[port].dtr_pin, \ ++ CONFIG_ETRAX_SER##port##_DTR_BIT); \ ++ else \ ++ serial_cris_ports[port].dtr_pin = dummy_pin; \ ++ if (strcmp(CONFIG_ETRAX_SER##port##_DSR_BIT, "")) \ ++ crisv32_io_get_name(&serial_cris_ports[port].dsr_pin, \ ++ CONFIG_ETRAX_SER##port##_DSR_BIT); \ ++ else \ ++ serial_cris_ports[port].dsr_pin = dummy_pin; \ ++ if (strcmp(CONFIG_ETRAX_SER##port##_RI_BIT, "")) \ ++ crisv32_io_get_name(&serial_cris_ports[port].ri_pin, \ ++ CONFIG_ETRAX_SER##port##_RI_BIT); \ ++ else \ ++ serial_cris_ports[port].ri_pin = dummy_pin; \ ++ if (strcmp(CONFIG_ETRAX_SER##port##_CD_BIT, "")) \ ++ crisv32_io_get_name(&serial_cris_ports[port].cd_pin, \ ++ CONFIG_ETRAX_SER##port##_CD_BIT); \ ++ else \ ++ serial_cris_ports[port].cd_pin = dummy_pin; \ ++ } ++ ++/* Set a serial port register if anything has changed. */ ++#define MODIFY_REG(instance, reg, var) \ ++ if (REG_RD_INT(ser, instance, reg) \ ++ != REG_TYPE_CONV(int, reg_ser_##reg, var)) \ ++ REG_WR(ser, instance, reg, var); ++ ++/* ++ * Regarding RS485 operation in crisv32 serial driver. ++ * --------------------------------------------------- ++ * RS485 can be run in two modes, full duplex using four wires (485FD) and ++ * half duplex using two wires (485HD). The default mode of each serial port ++ * is configured in the kernel configuration. The available modes are: ++ * RS-232, RS-485 half duplex, and RS-485 full duplex. ++ * ++ * In the 485HD mode the direction of the data bus must be able to switch. ++ * The direction of the transceiver is controlled by the RTS signal. Hence ++ * the auto_rts function in the ETRAX FS chip is enabled in this mode, which ++ * automatically toggle RTS when transmitting. The initial direction of the ++ * port is receiving. ++ * ++ * In the 485FD mode two transceivers will be used, one in each direction. ++ * Usually the hardware can handle both 485HD and 485FD, which implies that ++ * one of the transceivers can change direction. Consequently that transceiver ++ * must be tied to operate in the opposite direction of the other one, setting ++ * and keeping RTS to a fixed value do this. ++ * ++ * There are two special "ioctl" that can configure the ports. These two are ++ * left for backward compatible with older applications. The effects of using ++ * them are described below: ++ * The TIOCSERSETRS485: ++ * This ioctl sets a serial port in 232 mode to 485HD mode or vise versa. The ++ * state of the port is kept when closing the port. Note that this ioctl has no ++ * effect on a serial port in the 485FD mode. ++ * The TIOCSERWRRS485: ++ * This ioctl set a serial port in 232 mode to 485HD mode and writes the data ++ * "included" in the ioctl to the port. The port will then stay in 485HD mode. ++ * Using this ioctl on a serial port in the 485HD mode will transmit the data ++ * without changing the mode. Using this ioctl on a serial port in 485FD mode ++ * will not change the mode and simply send the data using the 485FD mode. ++ */ ++ ++#define TYPE_232 0 ++#define TYPE_485HD 1 ++#define TYPE_485FD 2 ++ ++struct etrax_recv_buffer { ++ struct etrax_recv_buffer *next; ++ unsigned short length; ++ unsigned char error; ++ unsigned char pad; ++ ++ unsigned char buffer[0]; ++}; ++ ++struct uart_cris_port { ++ struct uart_port port; ++ ++ int initialized; ++ int used; ++ int irq; ++ ++ /* Used to check if port enabled as well by testing for zero. */ ++ reg_scope_instances regi_ser; ++ reg_scope_instances regi_dmain; ++ reg_scope_instances regi_dmaout; ++ ++ struct crisv32_iopin dtr_pin; ++ struct crisv32_iopin dsr_pin; ++ struct crisv32_iopin ri_pin; ++ struct crisv32_iopin cd_pin; ++ ++ struct dma_descr_context tr_context_descr ++ __attribute__ ((__aligned__(32))); ++ struct dma_descr_data tr_descr[SERIAL_TX_DESCRIPTORS] ++ __attribute__ ((__aligned__(32))); ++ struct dma_descr_context rec_context_descr ++ __attribute__ ((__aligned__(32))); ++ struct dma_descr_data rec_descr[SERIAL_RECV_DESCRIPTORS] ++ __attribute__ ((__aligned__(32))); ++ ++ /* This is the first one in the list the HW is working on now. */ ++ struct dma_descr_data* first_tx_descr; ++ ++ /* This is the last one in the list the HW is working on now. */ ++ struct dma_descr_data* last_tx_descr; ++ ++ /* This is how many characters the HW is working on now. */ ++ unsigned int tx_pending_chars; ++ ++ int tx_started; ++ unsigned int cur_rec_descr; ++ struct etrax_recv_buffer *first_recv_buffer; ++ struct etrax_recv_buffer *last_recv_buffer; ++ ++ unsigned int recv_cnt; ++ unsigned int max_recv_cnt; ++ ++ /* The time for 1 char, in usecs. */ ++ unsigned long char_time_usec; ++ ++ /* Last tx usec in the jiffies. */ ++ unsigned long last_tx_active_usec; ++ ++ /* Last tx time in jiffies. */ ++ unsigned long last_tx_active; ++ ++ /* Last rx usec in the jiffies. */ ++ unsigned long last_rx_active_usec; ++ ++ /* Last rx time in jiffies. */ ++ unsigned long last_rx_active; ++ ++#ifdef CONFIG_ETRAX_RS485 ++ /* RS-485 support, duh. */ ++ struct rs485_control rs485; ++#endif ++ int port_type; ++}; ++ ++extern struct uart_driver serial_cris_driver; ++static struct uart_port *console_port; ++static int console_baud = 115200; ++static struct uart_cris_port serial_cris_ports[UART_NR] = { ++{ ++#ifdef CONFIG_ETRAX_SERIAL_PORT0 ++ .used = 1, ++ .irq = SER0_INTR_VECT, ++ .regi_ser = regi_ser0, ++ /* ++ * We initialize the dma stuff like this to get a compiler error ++ * if a CONFIG is missing ++ */ ++ .regi_dmain = ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN ++ regi_dma7, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_IN ++ regi_NULL, ++# endif ++ ++ .regi_dmaout = ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT ++ regi_dma6, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_OUT ++ regi_NULL, ++# endif ++ ++# ifdef CONFIG_ETRAX_RS485 ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_TYPE_485HD ++ .port_type = TYPE_485HD, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT0_TYPE_485FD ++ .port_type = TYPE_485FD, ++# endif ++# endif ++#else ++ .regi_ser = regi_NULL, ++ .regi_dmain = regi_NULL, ++ .regi_dmaout = regi_NULL, ++#endif ++}, /* ttyS0 */ ++{ ++#ifdef CONFIG_ETRAX_SERIAL_PORT1 ++ .used = 1, ++ .irq = SER1_INTR_VECT, ++ .regi_ser = regi_ser1, ++ .regi_dmain = ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA5_IN ++ regi_dma5, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_IN ++ regi_NULL, ++# endif ++ ++ .regi_dmaout = ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA4_OUT ++ regi_dma4, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_OUT ++ regi_NULL, ++# endif ++ ++# ifdef CONFIG_ETRAX_RS485 ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_TYPE_485HD ++ .port_type = TYPE_485HD, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT1_TYPE_485FD ++ .port_type = TYPE_485FD, ++# endif ++# endif ++#else ++ .regi_ser = regi_NULL, ++ .regi_dmain = regi_NULL, ++ .regi_dmaout = regi_NULL, ++#endif ++}, /* ttyS1 */ ++{ ++#ifdef CONFIG_ETRAX_SERIAL_PORT2 ++ .used = 1, ++ .irq = SER2_INTR_VECT, ++ .regi_ser = regi_ser2, ++ .regi_dmain = ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN ++ regi_dma3, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_IN ++ regi_NULL, ++# endif ++ ++ .regi_dmaout = ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT ++ regi_dma2, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_OUT ++ regi_NULL, ++# endif ++ ++# ifdef CONFIG_ETRAX_RS485 ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_TYPE_485HD ++ .port_type = TYPE_485HD, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT2_TYPE_485FD ++ .port_type = TYPE_485FD, ++# endif ++# endif ++#else ++ .regi_ser = regi_NULL, ++ .regi_dmain = regi_NULL, ++ .regi_dmaout = regi_NULL, ++#endif ++}, /* ttyS2 */ ++{ ++#ifdef CONFIG_ETRAX_SERIAL_PORT3 ++ .used = 1, ++ .irq = SER3_INTR_VECT, ++ .regi_ser = regi_ser3, ++ .regi_dmain = ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA9_IN ++ regi_dma9, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_IN ++ regi_NULL, ++# endif ++ ++ .regi_dmaout = ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA8_OUT ++ regi_dma8, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_OUT ++ regi_NULL, ++# endif ++ ++# ifdef CONFIG_ETRAX_RS485 ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_TYPE_485HD ++ .port_type = TYPE_485HD, ++# endif ++# ifdef CONFIG_ETRAX_SERIAL_PORT3_TYPE_485FD ++ .port_type = TYPE_485FD, ++# endif ++# endif ++#else ++ .regi_ser = regi_NULL, ++ .regi_dmain = regi_NULL, ++ .regi_dmaout = regi_NULL, ++#endif ++}, /* ttyS3 */ ++{ ++#ifdef CONFIG_ETRAX_DEBUG_PORT_NULL ++ .used = 1, ++#endif ++ .regi_ser = regi_NULL ++} /* Dummy console port */ ++ ++}; ++ ++/* Dummy pin used for unused CD, DSR, DTR and RI signals. */ ++static unsigned long io_dummy; ++static struct crisv32_ioport dummy_port = ++{ ++ &io_dummy, ++ &io_dummy, ++ &io_dummy, ++ 18 ++}; ++static struct crisv32_iopin dummy_pin = ++{ ++ &dummy_port, ++ 0 ++}; ++ ++static int selected_console = ++#if defined(CONFIG_ETRAX_DEBUG_PORT0) ++0; ++#elif defined(CONFIG_ETRAX_DEBUG_PORT1) ++1; ++#elif defined(CONFIG_ETRAX_DEBUG_PORT2) ++2; ++#elif defined(CONFIG_ETRAX_DEBUG_PORT3) ++3; ++#else /* CONFIG_ETRAX_DEBUG_PORT_NULL */ ++4; ++#endif ++ ++extern void reset_watchdog(void); ++ ++/* ++ * Interrupts are disabled on entering ++ */ ++static void ++cris_console_write(struct console *co, const char *s, unsigned int count) ++{ ++ struct uart_cris_port *up; ++ int i; ++ reg_ser_r_stat_din stat; ++ reg_ser_rw_tr_dma_en tr_dma_en, old; ++ ++ up = &serial_cris_ports[selected_console]; ++ ++ /* ++ * This function isn't covered by the struct uart_ops, so we ++ * have to check manually that the port really is there, ++ * configured and live. ++ */ ++ if (!up->regi_ser) ++ return; ++ ++ /* Switch to manual mode. */ ++ tr_dma_en = old = REG_RD (ser, up->regi_ser, rw_tr_dma_en); ++ if (tr_dma_en.en == regk_ser_yes) { ++ tr_dma_en.en = regk_ser_no; ++ REG_WR(ser, up->regi_ser, rw_tr_dma_en, tr_dma_en); ++ } ++ ++ /* Send data. */ ++ for (i = 0; i < count; i++) { ++ /* LF -> CRLF */ ++ if (s[i] == '\n') { ++ do { ++ stat = REG_RD (ser, up->regi_ser, r_stat_din); ++ } while (!stat.tr_rdy); ++ REG_WR_INT (ser, up->regi_ser, rw_dout, '\r'); ++ } ++ /* Wait until transmitter is ready and send. */ ++ do { ++ stat = REG_RD (ser, up->regi_ser, r_stat_din); ++ } while (!stat.tr_rdy); ++ REG_WR_INT (ser, up->regi_ser, rw_dout, s[i]); ++ ++ /* Feed watchdog, because this may take looong time. */ ++ reset_watchdog(); ++ } ++ ++ /* Restore mode. */ ++ if (tr_dma_en.en != old.en) ++ REG_WR(ser, up->regi_ser, rw_tr_dma_en, old); ++} ++ ++static void cris_serial_port_init(struct uart_port *port, int line); ++static int __init ++cris_console_setup(struct console *co, char *options) ++{ ++ struct uart_port *port; ++ int baud = 115200; ++ int bits = 8; ++ int parity = 'n'; ++ int flow = 'n'; ++ ++ if (co->index >= UART_NR) ++ co->index = 0; ++ if (options) ++ selected_console = co->index; ++ port = &serial_cris_ports[selected_console].port; ++ console_port = port; ++ ++ if (options) ++ uart_parse_options(options, &baud, &parity, &bits, &flow); ++ console_baud = baud; ++ cris_serial_port_init(port, selected_console); ++ co->index = port->line; ++ uart_set_options(port, co, baud, parity, bits, flow); ++ ++ return 0; ++} ++ ++static struct tty_driver* ++cris_console_device(struct console* co, int *index) ++{ ++ struct uart_driver *p = co->data; ++ *index = selected_console; ++ return p->tty_driver; ++} ++ ++static struct console cris_console = { ++ .name = "ttyS", ++ .write = cris_console_write, ++ .device = cris_console_device, ++ .setup = cris_console_setup, ++ .flags = CON_PRINTBUFFER, ++ .index = -1, ++ .data = &serial_cris_driver, ++}; ++ ++#define SERIAL_CRIS_CONSOLE &cris_console ++ ++struct uart_driver serial_cris_driver = { ++ .owner = THIS_MODULE, ++ .driver_name = "serial", ++ .dev_name = "ttyS", ++ .major = TTY_MAJOR, ++ .minor = 64, ++ .nr = UART_NR, ++ .cons = SERIAL_CRIS_CONSOLE, ++}; ++ ++static int inline crisv32_serial_get_rts(struct uart_cris_port *up) ++{ ++ reg_scope_instances regi_ser = up->regi_ser; ++ /* ++ * Return what the user has controlled rts to or ++ * what the pin is? (if auto_rts is used it differs during tx) ++ */ ++ reg_ser_r_stat_din rstat = REG_RD(ser, regi_ser, r_stat_din); ++ return !(rstat.rts_n == regk_ser_active); ++} ++ ++/* ++ * A set = 0 means 3.3V on the pin, bitvalue: 0=active, 1=inactive ++ * 0=0V , 1=3.3V ++ */ ++static inline void crisv32_serial_set_rts(struct uart_cris_port *up, int set) ++{ ++ reg_scope_instances regi_ser = up->regi_ser; ++ ++#ifdef CONFIG_ETRAX_RS485 ++ /* Never toggle RTS if port is in 485 mode. If port is in 485FD mode we ++ * do not want to send with the reciever and for 485HD mode auto_rts ++ * take care of the RTS for us. ++ */ ++ if (!up->rs485.enabled) { ++#else ++ { ++#endif ++ unsigned long flags; ++ reg_ser_rw_rec_ctrl rec_ctrl; ++ ++ local_irq_save(flags); ++ rec_ctrl = REG_RD(ser, regi_ser, rw_rec_ctrl); ++ if (set) ++ rec_ctrl.rts_n = regk_ser_active; ++ else ++ rec_ctrl.rts_n = regk_ser_inactive; ++ REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl); ++ local_irq_restore(flags); ++ } ++} ++ ++/* Input */ ++static int inline crisv32_serial_get_cts(struct uart_cris_port *up) ++{ ++ reg_scope_instances regi_ser = up->regi_ser; ++ reg_ser_r_stat_din rstat = REG_RD(ser, regi_ser, r_stat_din); ++ return (rstat.cts_n == regk_ser_active); ++} ++ ++/* ++ * Send a single character for XON/XOFF purposes. We do it in this separate ++ * function instead of the alternative support port.x_char, in the ...start_tx ++ * function, so we don't mix up this case with possibly enabling transmission ++ * of queued-up data (in case that's disabled after *receiving* an XOFF or ++ * negative CTS). This function is used for both DMA and non-DMA case; see HW ++ * docs specifically blessing sending characters manually when DMA for ++ * transmission is enabled and running. We may be asked to transmit despite ++ * the transmitter being disabled by a ..._stop_tx call so we need to enable ++ * it temporarily but restore the state afterwards. ++ * ++ * Beware: I'm not sure how the RS-485 stuff is supposed to work. Using ++ * XON/XOFF seems problematic if there are several controllers, but if it's ++ * actually RS-422 (multi-drop; one sender and multiple receivers), it might ++ * Just Work, so don't bail out just because it looks a little suspicious. ++ */ ++ ++void serial_cris_send_xchar(struct uart_port *port, char ch) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ reg_ser_rw_dout dout = { .data = ch }; ++ reg_ser_rw_ack_intr ack_intr = { .tr_rdy = regk_ser_yes }; ++ reg_ser_r_stat_din rstat; ++ reg_ser_rw_tr_ctrl prev_tr_ctrl, tr_ctrl; ++ reg_scope_instances regi_ser = up->regi_ser; ++ unsigned long flags; ++ ++ /* ++ * Wait for tr_rdy in case a character is already being output. Make ++ * sure we have integrity between the register reads and the writes ++ * below, but don't busy-wait with interrupts off and the port lock ++ * taken. ++ */ ++ spin_lock_irqsave(&port->lock, flags); ++ do { ++ spin_unlock_irqrestore(&port->lock, flags); ++ spin_lock_irqsave(&port->lock, flags); ++ prev_tr_ctrl = tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl); ++ rstat = REG_RD(ser, regi_ser, r_stat_din); ++ } while (!rstat.tr_rdy); ++ ++ /* ++ * Ack an interrupt if one was just issued for the previous character ++ * that was output. This is required for non-DMA as the interrupt is ++ * used as the only indicator that the transmitter is ready and it ++ * isn't while this x_char is being transmitted. ++ */ ++ REG_WR(ser, regi_ser, rw_ack_intr, ack_intr); ++ ++ /* Enable the transmitter in case it was disabled. */ ++ tr_ctrl.stop = 0; ++ REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl); ++ ++ /* ++ * Finally, send the blessed character; nothing should stop it now, ++ * except for an xoff-detected state, which we'll handle below. ++ */ ++ REG_WR(ser, regi_ser, rw_dout, dout); ++ up->port.icount.tx++; ++ ++ /* There might be an xoff state to clear. */ ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ ++ /* ++ * Clear any xoff state that *may* have been there to ++ * inhibit transmission of the character. ++ */ ++ if (rstat.xoff_detect) { ++ reg_ser_rw_xoff_clr xoff_clr = { .clr = 1 }; ++ REG_WR(ser, regi_ser, rw_xoff_clr, xoff_clr); ++ reg_ser_rw_tr_dma_en tr_dma_en ++ = REG_RD(ser, regi_ser, rw_tr_dma_en); ++ ++ /* ++ * If we had an xoff state but cleared it, instead sneak in a ++ * disabled state for the transmitter, after the character we ++ * sent. Thus we keep the port disabled, just as if the xoff ++ * state was still in effect (or actually, as if stop_tx had ++ * been called, as we stop DMA too). ++ */ ++ prev_tr_ctrl.stop = 1; ++ ++ tr_dma_en.en = 0; ++ REG_WR(ser, regi_ser, rw_tr_dma_en, tr_dma_en); ++ } ++ ++ /* Restore "previous" enabled/disabled state of the transmitter. */ ++ REG_WR(ser, regi_ser, rw_tr_ctrl, prev_tr_ctrl); ++ ++ spin_unlock_irqrestore(&port->lock, flags); ++} ++ ++static void transmit_chars_dma(struct uart_cris_port *up); ++ ++/* ++ * Do not spin_lock_irqsave or disable interrupts by other means here; it's ++ * already done by the caller. ++ */ ++ ++static void serial_cris_start_tx(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ reg_scope_instances regi_ser = up->regi_ser; ++ reg_ser_rw_tr_ctrl tr_ctrl; ++ ++ tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl); ++ tr_ctrl.stop = regk_ser_no; ++ REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl); ++ if (!up->regi_dmaout) { ++ reg_ser_rw_intr_mask intr_mask = ++ REG_RD(ser, regi_ser, rw_intr_mask); ++ intr_mask.tr_rdy = regk_ser_yes; ++ REG_WR(ser, regi_ser, rw_intr_mask, intr_mask); ++ } else { ++ /* ++ * We're called possibly to re-enable transmission after it ++ * has been disabled. If so, DMA needs to be re-enabled. ++ */ ++ reg_ser_rw_tr_dma_en tr_dma_en = { .en = 1 }; ++ REG_WR(ser, regi_ser, rw_tr_dma_en, tr_dma_en); ++ transmit_chars_dma(up); ++ } ++} ++ ++/* ++ * This function handles both the DMA and non-DMA case by ordering the ++ * transmitter to stop of after the current character. We don't need to wait ++ * for any such character to be completely transmitted; we do that where it ++ * matters, like in serial_cris_set_termios. Don't busy-wait here; see ++ * Documentation/serial/driver: this function is called within ++ * spin_lock_irq{,save} and thus separate ones would be disastrous (when SMP). ++ * There's no documented need to set the txd pin to any particular value; ++ * break setting is controlled solely by serial_cris_break_ctl. ++ */ ++ ++static void serial_cris_stop_tx(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ reg_scope_instances regi_ser = up->regi_ser; ++ reg_ser_rw_tr_ctrl tr_ctrl; ++ reg_ser_rw_intr_mask intr_mask; ++ reg_ser_rw_tr_dma_en tr_dma_en = {0}; ++ reg_ser_rw_xoff_clr xoff_clr = {0}; ++ ++ /* ++ * For the non-DMA case, we'd get a tr_rdy interrupt that we're not ++ * interested in as we're not transmitting any characters. For the ++ * DMA case, that interrupt is already turned off, but no reason to ++ * waste code on conditionals here. ++ */ ++ intr_mask = REG_RD(ser, regi_ser, rw_intr_mask); ++ intr_mask.tr_rdy = regk_ser_no; ++ REG_WR(ser, regi_ser, rw_intr_mask, intr_mask); ++ ++ tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl); ++ tr_ctrl.stop = 1; ++ REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl); ++ ++ /* ++ * Always clear possible hardware xoff-detected state here, no need to ++ * unnecessary consider mctrl settings and when they change. We clear ++ * it here rather than in start_tx: both functions are called as the ++ * effect of XOFF processing, but start_tx is also called when upper ++ * levels tell the driver that there are more characters to send, so ++ * avoid adding code there. ++ */ ++ xoff_clr.clr = 1; ++ REG_WR(ser, regi_ser, rw_xoff_clr, xoff_clr); ++ ++ /* ++ * Disable transmitter DMA, so that if we're in XON/XOFF, we can send ++ * those single characters without also giving go-ahead for queued up ++ * DMA data. ++ */ ++ tr_dma_en.en = 0; ++ REG_WR(ser, regi_ser, rw_tr_dma_en, tr_dma_en); ++} ++ ++static void serial_cris_stop_rx(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ reg_scope_instances regi_ser = up->regi_ser; ++ reg_ser_rw_rec_ctrl rec_ctrl = REG_RD(ser, regi_ser, rw_rec_ctrl); ++ ++ rec_ctrl.en = regk_ser_no; ++ REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl); ++} ++ ++static void serial_cris_enable_ms(struct uart_port *port) ++{ ++} ++ ++static void check_modem_status(struct uart_cris_port *up) ++{ ++} ++ ++static unsigned int serial_cris_tx_empty(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned long flags; ++ unsigned int ret; ++ reg_ser_r_stat_din rstat = {0}; ++ ++ spin_lock_irqsave(&up->port.lock, flags); ++ if (up->regi_dmaout) { ++ /* ++ * For DMA, before looking at r_stat, we need to check that we ++ * either haven't actually started or that end-of-list is ++ * reached, else a tr_empty indication is just an internal ++ * state. The caller qualifies, if needed, that the ++ * port->info.xmit buffer is empty, so we don't need to ++ * check that. ++ */ ++ reg_dma_rw_stat status = REG_RD(dma, up->regi_dmaout, rw_stat); ++ ++ if (!up->tx_started) { ++ ret = 1; ++ goto done; ++ } ++ ++ if (status.list_state != regk_dma_data_at_eol) { ++ ret = 0; ++ goto done; ++ } ++ } ++ ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ ret = rstat.tr_empty ? TIOCSER_TEMT : 0; ++ ++ done: ++ spin_unlock_irqrestore(&up->port.lock, flags); ++ return ret; ++} ++static unsigned int serial_cris_get_mctrl(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned int ret; ++ ++ ret = 0; ++ if (crisv32_serial_get_rts(up)) ++ ret |= TIOCM_RTS; ++ if (crisv32_io_rd(&up->dtr_pin)) ++ ret |= TIOCM_DTR; ++ if (crisv32_io_rd(&up->cd_pin)) ++ ret |= TIOCM_CD; ++ if (crisv32_io_rd(&up->ri_pin)) ++ ret |= TIOCM_RI; ++ if (!crisv32_io_rd(&up->dsr_pin)) ++ ret |= TIOCM_DSR; ++ if (crisv32_serial_get_cts(up)) ++ ret |= TIOCM_CTS; ++ return ret; ++} ++ ++static void serial_cris_set_mctrl(struct uart_port *port, unsigned int mctrl) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ ++ crisv32_serial_set_rts(up, mctrl & TIOCM_RTS ? 1 : 0); ++ crisv32_io_set(&up->dtr_pin, mctrl & TIOCM_DTR ? 1 : 0); ++ crisv32_io_set(&up->ri_pin, mctrl & TIOCM_RNG ? 1 : 0); ++ crisv32_io_set(&up->cd_pin, mctrl & TIOCM_CD ? 1 : 0); ++} ++ ++static void serial_cris_break_ctl(struct uart_port *port, int break_state) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned long flags; ++ reg_ser_rw_tr_ctrl tr_ctrl; ++ reg_ser_rw_tr_dma_en tr_dma_en; ++ reg_ser_rw_intr_mask intr_mask; ++ ++ spin_lock_irqsave(&up->port.lock, flags); ++ tr_ctrl = REG_RD(ser, up->regi_ser, rw_tr_ctrl); ++ tr_dma_en = REG_RD(ser, up->regi_ser, rw_tr_dma_en); ++ intr_mask = REG_RD(ser, up->regi_ser, rw_intr_mask); ++ ++ if (break_state != 0) { /* Send break */ ++ /* ++ * We need to disable DMA (if used) or tr_rdy interrupts if no ++ * DMA. No need to make this conditional on use of DMA; ++ * disabling will be a no-op for the other mode. ++ */ ++ intr_mask.tr_rdy = regk_ser_no; ++ tr_dma_en.en = 0; ++ ++ /* ++ * Stop transmission and set the txd pin to 0 after the ++ * current character. The txd setting will take effect after ++ * any current transmission has completed. ++ */ ++ tr_ctrl.stop = 1; ++ tr_ctrl.txd = 0; ++ } else { ++ /* Re-enable either transmit DMA or the serial interrupt. */ ++ if (up->regi_dmaout) ++ tr_dma_en.en = 1; ++ else ++ intr_mask.tr_rdy = regk_ser_yes; ++ ++ ++ tr_ctrl.stop = 0; ++ tr_ctrl.txd = 1; ++ } ++ REG_WR(ser, up->regi_ser, rw_tr_ctrl, tr_ctrl); ++ REG_WR(ser, up->regi_ser, rw_tr_dma_en, tr_dma_en); ++ REG_WR(ser, up->regi_ser, rw_intr_mask, intr_mask); ++ ++ spin_unlock_irqrestore(&up->port.lock, flags); ++} ++ ++/* ++ * The output DMA channel is free - use it to send as many chars as ++ * possible. ++ */ ++ ++static void ++transmit_chars_dma(struct uart_cris_port *up) ++{ ++ struct dma_descr_data *descr, *pending_descr, *dmapos; ++ struct dma_descr_data *last_tx_descr; ++ struct circ_buf *xmit = &up->port.info->xmit; ++ unsigned int sentl = 0; ++ reg_dma_rw_ack_intr ack_intr = { .data = regk_dma_yes }; ++ reg_dma_rw_stat status; ++ reg_scope_instances regi_dmaout = up->regi_dmaout; ++ unsigned int chars_in_q; ++ unsigned int chars_to_send; ++ ++ /* Acknowledge dma data descriptor irq, if there was one. */ ++ REG_WR(dma, regi_dmaout, rw_ack_intr, ack_intr); ++ ++ /* ++ * First get the amount of bytes sent during the last DMA transfer, ++ * and update xmit accordingly. ++ */ ++ status = REG_RD(dma, regi_dmaout, rw_stat); ++ if (status.list_state == regk_dma_data_at_eol || !up->tx_started) ++ dmapos = phys_to_virt((int)up->last_tx_descr->next); ++ else ++ dmapos = phys_to_virt(REG_RD_INT(dma, regi_dmaout, rw_data)); ++ ++ pending_descr = up->first_tx_descr; ++ while (pending_descr != dmapos) { ++ sentl += pending_descr->after - pending_descr->buf; ++ pending_descr->after = pending_descr->buf = NULL; ++ pending_descr = phys_to_virt((int)pending_descr->next); ++ } ++ ++ up->first_tx_descr = pending_descr; ++ last_tx_descr = up->last_tx_descr; ++ ++ /* Update stats. */ ++ up->port.icount.tx += sentl; ++ ++ up->tx_pending_chars -= sentl; ++ ++ /* Update xmit buffer. */ ++ xmit->tail = (xmit->tail + sentl) & (UART_XMIT_SIZE - 1); ++ ++ /* ++ * Find out the largest amount of consecutive bytes we want to send ++ * now. ++ */ ++ chars_in_q = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); ++ ++ if (chars_in_q == 0) ++ /* Tell upper layers that we're now idle. */ ++ goto done; ++ ++ /* Some of those characters are actually pending output. */ ++ chars_to_send = chars_in_q - up->tx_pending_chars; ++ ++ /* ++ * Clamp the new number of pending chars to the advertised ++ * one. ++ */ ++ if (chars_to_send + up->tx_pending_chars > up->port.fifosize) ++ chars_to_send = up->port.fifosize - up->tx_pending_chars; ++ ++ /* If we don't want to send any, we're done. */ ++ if (chars_to_send == 0) ++ goto done; ++ ++ descr = phys_to_virt((int)last_tx_descr->next); ++ ++ /* ++ * We can't send anything if we could make the condition in ++ * the while-loop above (reaping finished descriptors) be met ++ * immediately before the first iteration. However, don't ++ * mistake the full state for the empty state. ++ */ ++ if ((descr == up->first_tx_descr && up->tx_pending_chars != 0) ++ || descr->next == up->first_tx_descr) ++ goto done; ++ ++ /* Set up the descriptor for output. */ ++ descr->buf = (void*)virt_to_phys(xmit->buf + xmit->tail ++ + up->tx_pending_chars); ++ descr->after = descr->buf + chars_to_send; ++ descr->eol = 1; ++ descr->out_eop = 0; ++ descr->intr = 1; ++ descr->wait = 0; ++ descr->in_eop = 0; ++ descr->md = 0; ++ /* ++ * Make sure GCC doesn't move this eol clear before the eol set ++ * above. ++ */ ++ barrier(); ++ last_tx_descr->eol = 0; ++ ++ up->last_tx_descr = descr; ++ up->tx_pending_chars += chars_to_send; ++ ++ if (!up->tx_started) { ++ up->tx_started = 1; ++ up->tr_context_descr.next = 0; ++ up->tr_context_descr.saved_data ++ = (dma_descr_data*)virt_to_phys(descr); ++ up->tr_context_descr.saved_data_buf = descr->buf; ++ DMA_START_CONTEXT(regi_dmaout, ++ virt_to_phys(&up->tr_context_descr)); ++ } else ++ DMA_CONTINUE_DATA(regi_dmaout); ++ ++ /* DMA is now running (hopefully). */ ++ ++ done: ++ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) ++ uart_write_wakeup(&up->port); ++} ++ ++static void ++transmit_chars_no_dma(struct uart_cris_port *up) ++{ ++ int count; ++ struct circ_buf *xmit = &up->port.info->xmit; ++ ++ reg_scope_instances regi_ser = up->regi_ser; ++ reg_ser_r_stat_din rstat; ++ reg_ser_rw_ack_intr ack_intr = { .tr_rdy = regk_ser_yes }; ++ ++ if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { ++ /* No more to send, so disable the interrupt. */ ++ reg_ser_rw_intr_mask intr_mask; ++ intr_mask = REG_RD(ser, regi_ser, rw_intr_mask); ++ intr_mask.tr_rdy = 0; ++ intr_mask.tr_empty = 0; ++ REG_WR(ser, regi_ser, rw_intr_mask, intr_mask); ++ return; ++ } ++ ++ count = ETRAX_SER_FIFO_SIZE; ++ do { ++ reg_ser_rw_dout dout = { .data = xmit->buf[xmit->tail] }; ++ REG_WR(ser, regi_ser, rw_dout, dout); ++ REG_WR(ser, regi_ser, rw_ack_intr, ack_intr); ++ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE-1); ++ up->port.icount.tx++; ++ if (xmit->head == xmit->tail) ++ break; ++ rstat = REG_RD(ser, regi_ser, r_stat_din); ++ } while ((--count > 0) && rstat.tr_rdy); ++ ++ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) ++ uart_write_wakeup(&up->port); ++} /* transmit_chars_no_dma */ ++ ++static struct etrax_recv_buffer * ++alloc_recv_buffer(unsigned int size) ++{ ++ struct etrax_recv_buffer *buffer; ++ ++ if (!(buffer = kmalloc(sizeof *buffer + size, GFP_ATOMIC))) ++ panic("%s: Could not allocate %d bytes buffer\n", ++ __FUNCTION__, size); ++ ++ buffer->next = NULL; ++ buffer->length = 0; ++ buffer->error = TTY_NORMAL; ++ ++ return buffer; ++} ++ ++static void ++append_recv_buffer(struct uart_cris_port *up, ++ struct etrax_recv_buffer *buffer) ++{ ++ unsigned long flags; ++ ++ local_irq_save(flags); ++ ++ if (!up->first_recv_buffer) ++ up->first_recv_buffer = buffer; ++ else ++ up->last_recv_buffer->next = buffer; ++ ++ up->last_recv_buffer = buffer; ++ ++ up->recv_cnt += buffer->length; ++ if (up->recv_cnt > up->max_recv_cnt) ++ up->max_recv_cnt = up->recv_cnt; ++ ++ local_irq_restore(flags); ++} ++ ++static int ++add_char_and_flag(struct uart_cris_port *up, unsigned char data, ++ unsigned char flag) ++{ ++ struct etrax_recv_buffer *buffer; ++ ++ buffer = alloc_recv_buffer(4); ++ buffer->length = 1; ++ buffer->error = flag; ++ buffer->buffer[0] = data; ++ ++ append_recv_buffer(up, buffer); ++ ++ up->port.icount.rx++; ++ ++ return 1; ++} ++ ++static void ++flush_to_flip_buffer(struct uart_cris_port *up) ++{ ++ struct tty_struct *tty; ++ struct etrax_recv_buffer *buffer; ++ ++ tty = up->port.info->tty; ++ if (!up->first_recv_buffer || !tty) ++ return; ++ ++ while ((buffer = up->first_recv_buffer)) { ++ unsigned int count = (unsigned int) ++ tty_insert_flip_string(tty, buffer->buffer, ++ buffer->length); ++ ++ up->recv_cnt -= count; ++ ++ if (count == buffer->length) { ++ up->first_recv_buffer = buffer->next; ++ kfree(buffer); ++ } else { ++ buffer->length -= count; ++ memmove(buffer->buffer, buffer->buffer + count, ++ buffer->length); ++ buffer->error = TTY_NORMAL; ++ } ++ } ++ ++ if (!up->first_recv_buffer) ++ up->last_recv_buffer = NULL; ++ ++ /* This call includes a check for low-latency. */ ++ tty_flip_buffer_push(tty); ++} ++ ++static unsigned int ++handle_descr_data(struct uart_cris_port *up, struct dma_descr_data *descr, ++ unsigned int recvl) ++{ ++ struct etrax_recv_buffer *buffer ++ = phys_to_virt((unsigned long)descr->buf) - sizeof *buffer; ++ ++ if (up->recv_cnt + recvl > 65536) { ++ printk(KERN_ERR "Too much pending incoming data on %s!" ++ " Dropping %u bytes.\n", up->port.info->tty->name, ++ recvl); ++ return 0; ++ } ++ ++ buffer->length = recvl; ++ ++ append_recv_buffer(up, buffer); ++ ++ flush_to_flip_buffer(up); ++ ++ buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE); ++ descr->buf = (void*)virt_to_phys(buffer->buffer); ++ descr->after = descr->buf + SERIAL_DESCR_BUF_SIZE; ++ ++ return recvl; ++} ++ ++static unsigned int ++handle_all_descr_data(struct uart_cris_port *up) ++{ ++ struct dma_descr_data *descr ++ = &up->rec_descr[(up->cur_rec_descr - 1) ++ % SERIAL_RECV_DESCRIPTORS]; ++ struct dma_descr_data *prev_descr; ++ unsigned int recvl; ++ unsigned int ret = 0; ++ reg_scope_instances regi_dmain = up->regi_dmain; ++ ++ while (1) { ++ prev_descr = descr; ++ descr = &up->rec_descr[up->cur_rec_descr]; ++ ++ if (descr == phys_to_virt(REG_RD(dma, regi_dmain, rw_data))) ++ break; ++ ++ if (++up->cur_rec_descr == SERIAL_RECV_DESCRIPTORS) ++ up->cur_rec_descr = 0; ++ ++ /* Find out how many bytes were read. */ ++ recvl = descr->after - descr->buf; ++ ++ /* Update stats. */ ++ up->port.icount.rx += recvl; ++ ++ ret += handle_descr_data(up, descr, recvl); ++ descr->eol = 1; ++ /* ++ * Make sure GCC doesn't move this eol clear before the ++ * eol set above. ++ */ ++ barrier(); ++ prev_descr->eol = 0; ++ flush_dma_descr(descr,1); // Cache bug workaround ++ flush_dma_descr(prev_descr,0); // Cache bug workaround ++ } ++ ++ return ret; ++} ++ ++static void ++receive_chars_dma(struct uart_cris_port *up) ++{ ++ reg_ser_r_stat_din rstat; ++ reg_dma_rw_ack_intr ack_intr = {0}; ++ ++ /* Acknowledge both dma_descr and dma_eop irq. */ ++ ack_intr.data = 1; ++ ack_intr.in_eop = 1; ++ REG_WR(dma, up->regi_dmain, rw_ack_intr, ack_intr); ++ ++ handle_all_descr_data(up); ++ ++ /* Read the status register to detect errors. */ ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ ++ if (rstat.framing_err | rstat.par_err | rstat.orun) { ++ /* ++ * If we got an error, we must reset it by reading the ++ * rs_stat_din register and put the data in buffer manually. ++ */ ++ reg_ser_rs_stat_din stat_din; ++ stat_din = REG_RD(ser, up->regi_ser, rs_stat_din); ++ ++ if (stat_din.par_err) ++ add_char_and_flag(up, stat_din.data, TTY_PARITY); ++ else if (stat_din.orun) ++ add_char_and_flag(up, stat_din.data, TTY_OVERRUN); ++ else if (stat_din.framing_err) ++ add_char_and_flag(up, stat_din.data, TTY_FRAME); ++ } ++ ++ /* Restart the receiving DMA, in case it got stuck on an EOL. */ ++ DMA_CONTINUE_DATA(up->regi_dmain); ++} ++ ++void receive_chars_no_dma(struct uart_cris_port *up) ++{ ++ reg_ser_rs_stat_din stat_din; ++ reg_ser_r_stat_din rstat; ++ struct tty_struct *tty; ++ struct uart_icount *icount; ++ int max_count = 16; ++ char flag; ++ reg_ser_rw_ack_intr ack_intr = { 0 }; ++ ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ up->last_rx_active_usec = GET_JIFFIES_USEC(); ++ up->last_rx_active = jiffies; ++ icount = &up->port.icount; ++ tty = up->port.info->tty; ++ ++ do { ++ stat_din = REG_RD(ser, up->regi_ser, rs_stat_din); ++ ++ flag = TTY_NORMAL; ++ ack_intr.dav = 1; ++ REG_WR(ser, up->regi_ser, rw_ack_intr, ack_intr); ++ icount->rx++; ++ ++ if (stat_din.framing_err | stat_din.par_err | stat_din.orun) { ++ if (stat_din.data == 0x00 && ++ stat_din.framing_err) { ++ /* Most likely a break. */ ++ flag = TTY_BREAK; ++ icount->brk++; ++ } else if (stat_din.par_err) { ++ flag = TTY_PARITY; ++ icount->parity++; ++ } else if (stat_din.orun) { ++ flag = TTY_OVERRUN; ++ icount->overrun++; ++ } else if (stat_din.framing_err) { ++ flag = TTY_FRAME; ++ icount->frame++; ++ } ++ } ++ ++ /* ++ * If this becomes important, we probably *could* handle this ++ * gracefully by keeping track of the unhandled character. ++ */ ++ if (!tty_insert_flip_char(tty, stat_din.data, flag)) ++ panic("%s: No tty buffer space", __FUNCTION__); ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ } while (rstat.dav && (max_count-- > 0)); ++ spin_unlock(&up->port.lock); ++ tty_flip_buffer_push(tty); ++ spin_lock(&up->port.lock); ++} /* receive_chars_no_dma */ ++ ++/* ++ * DMA output channel interrupt handler. ++ * this interrupt is called from DMA2(ser2), DMA8(ser3), DMA6(ser0) or ++ * DMA4(ser1) when they have finished a descriptor with the intr flag set. ++ */ ++ ++static irqreturn_t ++dma_tr_interrupt(int irq, void *dev_id, struct pt_regs * regs) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)dev_id; ++ reg_dma_r_masked_intr masked_intr; ++ reg_scope_instances regi_dmaout; ++ int handled = 0; ++ ++ spin_lock(&up->port.lock); ++ regi_dmaout = up->regi_dmaout; ++ if (!regi_dmaout) { ++ spin_unlock(&up->port.lock); ++ return IRQ_NONE; ++ } ++ ++ /* ++ * Check for dma_descr (don't need to check for dma_eop in ++ * output DMA for serial). ++ */ ++ masked_intr = REG_RD(dma, regi_dmaout, r_masked_intr); ++ ++ if (masked_intr.data) { ++ /* We can send a new dma bunch. make it so. */ ++ ++ /* ++ * Read jiffies_usec first. ++ * We want this time to be as late as possible. ++ */ ++ up->last_tx_active_usec = GET_JIFFIES_USEC(); ++ up->last_tx_active = jiffies; ++ transmit_chars_dma(up); ++ handled = 1; ++ } ++ check_modem_status(up); ++ spin_unlock(&up->port.lock); ++ return IRQ_RETVAL(handled); ++} ++ ++/* DMA input channel interrupt handler. */ ++ ++static irqreturn_t ++dma_rec_interrupt(int irq, void *dev_id, struct pt_regs * regs) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)dev_id; ++ reg_dma_r_masked_intr masked_intr; ++ reg_scope_instances regi_dmain; ++ int handled = 0; ++ ++ spin_lock(&up->port.lock); ++ regi_dmain = up->regi_dmain; ++ if (!regi_dmain) { ++ spin_unlock(&up->port.lock); ++ return IRQ_NONE; ++ } ++ ++ /* Check for both dma_eop and dma_descr for the input dma channel. */ ++ masked_intr = REG_RD(dma, regi_dmain, r_masked_intr); ++ if (masked_intr.data || masked_intr.in_eop) { ++ /* We have received something. */ ++ receive_chars_dma(up); ++ handled = 1; ++ } ++ check_modem_status(up); ++ spin_unlock(&up->port.lock); ++ return IRQ_RETVAL(handled); ++} ++ ++/* "Normal" serial port interrupt handler - both rx and tx. */ ++ ++static irqreturn_t ++ser_interrupt(int irq, void *dev_id, struct pt_regs *regs) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)dev_id; ++ reg_scope_instances regi_ser; ++ int handled = 0; ++ ++ spin_lock(&up->port.lock); ++ if (up->regi_dmain && up->regi_dmaout) { ++ spin_unlock(&up->port.lock); ++ return IRQ_NONE; ++ } ++ ++ regi_ser = up->regi_ser; ++ ++ if (regi_ser) { ++ reg_ser_r_masked_intr masked_intr; ++ masked_intr = REG_RD(ser, regi_ser, r_masked_intr); ++ /* ++ * Check what interrupts are active before taking ++ * actions. If DMA is used the interrupt shouldn't ++ * be enabled. ++ */ ++ if (masked_intr.dav) { ++ receive_chars_no_dma(up); ++ handled = 1; ++ } ++ check_modem_status(up); ++ ++ if (masked_intr.tr_rdy) { ++ transmit_chars_no_dma(up); ++ handled = 1; ++ } ++ } ++ spin_unlock(&up->port.lock); ++ return IRQ_RETVAL(handled); ++} /* ser_interrupt */ ++ ++static int start_recv_dma(struct uart_cris_port *up) ++{ ++ struct dma_descr_data *descr = up->rec_descr; ++ struct etrax_recv_buffer *buffer; ++ int i; ++ ++ /* Set up the receiving descriptors. */ ++ for (i = 0; i < SERIAL_RECV_DESCRIPTORS; i++) { ++ buffer = alloc_recv_buffer(SERIAL_DESCR_BUF_SIZE); ++ descr[i].next = (void*)virt_to_phys(&descr[i+1]); ++ descr[i].buf = (void*)virt_to_phys(buffer->buffer); ++ descr[i].after = descr[i].buf + SERIAL_DESCR_BUF_SIZE; ++ descr[i].eol = 0; ++ descr[i].out_eop = 0; ++ descr[i].intr = 1; ++ descr[i].wait = 0; ++ descr[i].in_eop = 0; ++ descr[i].md = 0; ++ ++ } ++ ++ /* Link the last descriptor to the first. */ ++ descr[i-1].next = (void*)virt_to_phys(&descr[0]); ++ ++ /* And mark it as end of list. */ ++ descr[i-1].eol = 1; ++ ++ /* Start with the first descriptor in the list. */ ++ up->cur_rec_descr = 0; ++ up->rec_context_descr.next = 0; ++ up->rec_context_descr.saved_data ++ = (dma_descr_data *)virt_to_phys(&descr[up->cur_rec_descr]); ++ up->rec_context_descr.saved_data_buf = descr[up->cur_rec_descr].buf; ++ ++ /* Start the DMA. */ ++ DMA_START_CONTEXT(up->regi_dmain, ++ virt_to_phys(&up->rec_context_descr)); ++ ++ /* Input DMA should be running now. */ ++ return 1; ++} ++ ++ ++static void start_receive(struct uart_cris_port *up) ++{ ++ reg_scope_instances regi_dmain = up->regi_dmain; ++ if (regi_dmain) { ++ start_recv_dma(up); ++ } ++} ++ ++ ++static void start_transmitter(struct uart_cris_port *up) ++{ ++ int i; ++ reg_scope_instances regi_dmaout = up->regi_dmaout; ++ if (regi_dmaout) { ++ for (i = 0; i < SERIAL_TX_DESCRIPTORS; i++) { ++ memset(&up->tr_descr[i], 0, sizeof(up->tr_descr[i])); ++ up->tr_descr[i].eol = 1; ++ up->tr_descr[i].intr = 1; ++ up->tr_descr[i].next = (dma_descr_data *) ++ virt_to_phys(&up->tr_descr[i+1]); ++ } ++ up->tr_descr[i-1].next = (dma_descr_data *) ++ virt_to_phys(&up->tr_descr[0]); ++ up->first_tx_descr = &up->tr_descr[0]; ++ ++ /* ++ * We'll be counting up to up->last_tx_descr->next from ++ * up->first_tx_descr when starting DMA, so we should make ++ * them the same for the very first round. If instead we'd ++ * set last_tx_descr = first_tx_descr, we'd rely on ++ * accidentally working code and data as we'd take a pass over ++ * the first, unused, descriptor. ++ */ ++ up->last_tx_descr = &up->tr_descr[i-1]; ++ up->tx_started = 0; ++ up->tx_pending_chars = 0; ++ } ++} ++ ++static int serial_cris_startup(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned long flags; ++ reg_intr_vect_rw_mask intr_mask; ++ reg_ser_rw_intr_mask ser_intr_mask = {0}; ++ reg_dma_rw_intr_mask dmain_intr_mask = {0}; ++ reg_dma_rw_intr_mask dmaout_intr_mask = {0}; ++ reg_dma_rw_cfg cfg = {.en = 1}; ++ reg_scope_instances regi_dma; ++ ++ spin_lock_irqsave(&up->port.lock, flags); ++ ++ intr_mask = REG_RD(intr_vect, regi_irq, rw_mask); ++ ++ dmain_intr_mask.data = dmain_intr_mask.in_eop = regk_dma_yes; ++ dmaout_intr_mask.data = regk_dma_yes; ++ if (!up->regi_dmain) ++ ser_intr_mask.dav = regk_ser_yes; ++ ++ if (port->line == 0) { ++ if (request_irq(SER0_INTR_VECT, ser_interrupt, ++ IRQF_SHARED | IRQF_DISABLED, "ser0", ++ &serial_cris_ports[0])) ++ panic("irq ser0"); ++ /* Enable the ser0 irq in global config. */ ++ intr_mask.ser0 = 1; ++ /* Port ser0 can use dma6 for tx and dma7 for rx. */ ++#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT ++ if (request_irq(DMA6_INTR_VECT, dma_tr_interrupt, ++ IRQF_DISABLED, "serial 0 dma tr", ++ &serial_cris_ports[0])) ++ panic("irq ser0txdma"); ++ crisv32_request_dma(6, "ser0", DMA_PANIC_ON_ERROR, 0, ++ dma_ser0); ++ /* Enable the dma6 irq in global config. */ ++ intr_mask.dma6 = 1; ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN ++ if (request_irq(DMA7_INTR_VECT, dma_rec_interrupt, ++ IRQF_DISABLED, "serial 0 dma rec", ++ &serial_cris_ports[0])) ++ panic("irq ser0rxdma"); ++ crisv32_request_dma(7, "ser0", DMA_PANIC_ON_ERROR, 0, ++ dma_ser0); ++ /* Enable the dma7 irq in global config. */ ++ intr_mask.dma7 = 1; ++#endif ++ } else if (port->line == 1) { ++ if (request_irq(SER1_INTR_VECT, ser_interrupt, ++ IRQF_SHARED | IRQF_DISABLED, "ser1", ++ &serial_cris_ports[1])) ++ panic("irq ser1"); ++ /* Enable the ser1 irq in global config. */ ++ intr_mask.ser1 = 1; ++ ++ /* Port ser1 can use dma4 for tx and dma5 for rx. */ ++#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA4_OUT ++ if (request_irq(DMA4_INTR_VECT, dma_tr_interrupt, ++ IRQF_DISABLED, "serial 1 dma tr", ++ &serial_cris_ports[1])) ++ panic("irq ser1txdma"); ++ crisv32_request_dma(4, "ser1", DMA_PANIC_ON_ERROR, 0, ++ dma_ser1); ++ /* Enable the dma4 irq in global config. */ ++ intr_mask.dma4 = 1; ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA5_IN ++ if (request_irq(DMA5_INTR_VECT, dma_rec_interrupt, ++ IRQF_DISABLED, "serial 1 dma rec", ++ &serial_cris_ports[1])) ++ panic("irq ser1rxdma"); ++ crisv32_request_dma(5, "ser1", DMA_PANIC_ON_ERROR, 0, ++ dma_ser1); ++ /* Enable the dma5 irq in global config. */ ++ intr_mask.dma5 = 1; ++#endif ++ } else if (port->line == 2) { ++ if (request_irq(SER2_INTR_VECT, ser_interrupt, ++ IRQF_SHARED | IRQF_DISABLED, "ser2", ++ &serial_cris_ports[2])) ++ panic("irq ser2"); ++ /* Enable the ser2 irq in global config. */ ++ intr_mask.ser2 = 1; ++ ++ /* Port ser2 can use dma2 for tx and dma3 for rx. */ ++#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT ++ if (request_irq(DMA2_INTR_VECT, dma_tr_interrupt, ++ IRQF_DISABLED, "serial 2 dma tr", ++ &serial_cris_ports[2])) ++ panic("irq ser2txdma"); ++ crisv32_request_dma(2, "ser2", DMA_PANIC_ON_ERROR, 0, ++ dma_ser2); ++ /* Enable the dma2 irq in global config. */ ++ intr_mask.dma2 = 1; ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN ++ if (request_irq(DMA3_INTR_VECT, dma_rec_interrupt, ++ IRQF_DISABLED, "serial 2 dma rec", ++ &serial_cris_ports[2])) ++ panic("irq ser2rxdma"); ++ crisv32_request_dma(3, "ser2", DMA_PANIC_ON_ERROR, 0, ++ dma_ser2); ++ /* Enable the dma3 irq in global config. */ ++ intr_mask.dma3 = 1; ++#endif ++ } else if (port->line == 3) { ++ if (request_irq(SER3_INTR_VECT, ser_interrupt, ++ IRQF_SHARED | IRQF_DISABLED, "ser3", ++ &serial_cris_ports[3])) ++ panic("irq ser3" ); ++ /* Enable the ser3 irq in global config. */ ++ intr_mask.ser3 = 1; ++ ++ /* Port ser3 can use dma8 for tx and dma9 for rx. */ ++#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA8_OUT ++ if (request_irq(DMA8_INTR_VECT, dma_tr_interrupt, ++ IRQF_DISABLED, "serial 3 dma tr", ++ &serial_cris_ports[3])) ++ panic("irq ser3txdma"); ++ crisv32_request_dma(8, "ser3", DMA_PANIC_ON_ERROR, 0, ++ dma_ser3); ++ /* Enable the dma2 irq in global config. */ ++ intr_mask.dma8 = 1; ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA9_IN ++ if (request_irq(DMA9_INTR_VECT, dma_rec_interrupt, ++ IRQF_DISABLED, "serial 3 dma rec", ++ &serial_cris_ports[3])) ++ panic("irq ser3rxdma"); ++ crisv32_request_dma(9, "ser3", DMA_PANIC_ON_ERROR, 0, ++ dma_ser3); ++ /* Enable the dma3 irq in global config. */ ++ intr_mask.dma9 = 1; ++#endif ++ } ++ ++ /* ++ * Reset the DMA channels and make sure their interrupts are cleared. ++ */ ++ ++ regi_dma = up->regi_dmain; ++ if (regi_dma) { ++ reg_dma_rw_ack_intr ack_intr = { 0 }; ++ DMA_RESET(regi_dma); ++ /* Wait until reset cycle is complete. */ ++ DMA_WAIT_UNTIL_RESET(regi_dma); ++ REG_WR(dma, regi_dma, rw_cfg, cfg); ++ /* Make sure the irqs are cleared. */ ++ ack_intr.group = 1; ++ ack_intr.ctxt = 1; ++ ack_intr.data = 1; ++ ack_intr.in_eop = 1; ++ ack_intr.stream_cmd = 1; ++ REG_WR(dma, regi_dma, rw_ack_intr, ack_intr); ++ } ++ regi_dma = up->regi_dmaout; ++ if (regi_dma) { ++ reg_dma_rw_ack_intr ack_intr = { 0 }; ++ DMA_RESET(regi_dma); ++ /* Wait until reset cycle is complete. */ ++ DMA_WAIT_UNTIL_RESET(regi_dma); ++ REG_WR(dma, regi_dma, rw_cfg, cfg); ++ /* Make sure the irqs are cleared. */ ++ ack_intr.group = 1; ++ ack_intr.ctxt = 1; ++ ack_intr.data = 1; ++ ack_intr.in_eop = 1; ++ ack_intr.stream_cmd = 1; ++ REG_WR(dma, regi_dma, rw_ack_intr, ack_intr); ++ } ++ ++ REG_WR(intr_vect, regi_irq, rw_mask, intr_mask); ++ REG_WR(ser, up->regi_ser, rw_intr_mask, ser_intr_mask); ++ if (up->regi_dmain) ++ REG_WR(dma, up->regi_dmain, rw_intr_mask, dmain_intr_mask); ++ if (up->regi_dmaout) ++ REG_WR(dma, up->regi_dmaout, rw_intr_mask, dmaout_intr_mask); ++ ++ start_receive(up); ++ start_transmitter(up); ++ ++ serial_cris_set_mctrl(&up->port, up->port.mctrl); ++ spin_unlock_irqrestore(&up->port.lock, flags); ++ ++ return 0; ++} ++ ++static void serial_cris_shutdown(struct uart_port *port) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned long flags; ++ reg_intr_vect_rw_mask intr_mask; ++ ++ spin_lock_irqsave(&up->port.lock, flags); ++ ++ intr_mask = REG_RD(intr_vect, regi_irq, rw_mask); ++ serial_cris_stop_tx(port); ++ serial_cris_stop_rx(port); ++ ++ if (port->line == 0) { ++ intr_mask.ser0 = 0; ++ free_irq(SER0_INTR_VECT, &serial_cris_ports[0]); ++#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT ++ intr_mask.dma6 = 0; ++ crisv32_free_dma(6); ++ free_irq(DMA6_INTR_VECT, &serial_cris_ports[0]); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN ++ intr_mask.dma7 = 0; ++ crisv32_free_dma(7); ++ free_irq(DMA7_INTR_VECT, &serial_cris_ports[0]); ++#endif ++ } else if (port->line == 1) { ++ intr_mask.ser1 = 0; ++ free_irq(SER1_INTR_VECT, &serial_cris_ports[1]); ++#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA4_OUT ++ intr_mask.dma4 = 0; ++ crisv32_free_dma(4); ++ free_irq(DMA4_INTR_VECT, &serial_cris_ports[1]); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA5_IN ++ intr_mask.dma5 = 0; ++ crisv32_free_dma(5); ++ free_irq(DMA5_INTR_VECT, &serial_cris_ports[1]); ++#endif ++ } else if (port->line == 2) { ++ intr_mask.ser2 = 0; ++ free_irq(SER2_INTR_VECT, &serial_cris_ports[2]); ++#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT ++ intr_mask.dma2 = 0; ++ crisv32_free_dma(2); ++ free_irq(DMA2_INTR_VECT, &serial_cris_ports[2]); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN ++ intr_mask.dma3 = 0; ++ crisv32_free_dma(3); ++ free_irq(DMA3_INTR_VECT, &serial_cris_ports[2]); ++#endif ++ } else if (port->line == 3) { ++ intr_mask.ser3 = 0; ++ free_irq(SER3_INTR_VECT, &serial_cris_ports[3]); ++#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA8_OUT ++ intr_mask.dma8 = 0; ++ crisv32_free_dma(8); ++ free_irq(DMA8_INTR_VECT, &serial_cris_ports[3]); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA9_IN ++ intr_mask.dma9 = 0; ++ crisv32_free_dma(9); ++ free_irq(DMA9_INTR_VECT, &serial_cris_ports[3]); ++#endif ++ } ++ ++ REG_WR(intr_vect, regi_irq, rw_mask, intr_mask); ++ ++ serial_cris_set_mctrl(&up->port, up->port.mctrl); ++ ++ if (up->regi_dmain) { ++ struct etrax_recv_buffer *rb; ++ struct etrax_recv_buffer *rb_next; ++ int i; ++ struct dma_descr_data *descr; ++ ++ /* ++ * In case of DMA and receive errors, there might be pending ++ * receive buffers still linked here and not flushed upwards. ++ * Release them. ++ */ ++ for (rb = up->first_recv_buffer; rb != NULL; rb = rb_next) { ++ rb_next = rb->next; ++ kfree (rb); ++ } ++ up->first_recv_buffer = NULL; ++ up->last_recv_buffer = NULL; ++ ++ /* ++ * Also release buffers that were attached to the DMA ++ * before we shut down the hardware above. ++ */ ++ for (i = 0, descr = up->rec_descr; ++ i < SERIAL_RECV_DESCRIPTORS; ++ i++) ++ if (descr[i].buf) { ++ rb = phys_to_virt((u32) descr[i].buf) ++ - sizeof *rb; ++ kfree(rb); ++ descr[i].buf = NULL; ++ } ++ } ++ ++ spin_unlock_irqrestore(&up->port.lock, flags); ++ ++} ++ ++static void ++serial_cris_set_termios(struct uart_port *port, struct termios *termios, ++ struct termios *old) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ unsigned long flags; ++ reg_ser_rw_xoff xoff; ++ reg_ser_rw_xoff_clr xoff_clr = {0}; ++ reg_ser_rw_tr_ctrl tx_ctrl = {0}; ++ reg_ser_rw_tr_dma_en tx_dma_en = {0}; ++ reg_ser_rw_rec_ctrl rx_ctrl = {0}; ++ reg_ser_rw_tr_baud_div tx_baud_div = {0}; ++ reg_ser_rw_rec_baud_div rx_baud_div = {0}; ++ reg_ser_r_stat_din rstat; ++ int baud; ++ ++ if (old && ++ termios->c_cflag == old->c_cflag && ++ termios->c_iflag == old->c_iflag) ++ return; ++ ++ /* Start with default settings and then fill in changes. */ ++ ++ /* Tx: 8 bit, no/even parity, 1 stop bit, no cts. */ ++ tx_ctrl.base_freq = regk_ser_f29_493; ++ tx_ctrl.en = 0; ++ tx_ctrl.stop = 0; ++#ifdef CONFIG_ETRAX_RS485 ++ if (up->rs485.enabled && (up->port_type != TYPE_485FD)) { ++ tx_ctrl.auto_rts = regk_ser_yes; ++ } else ++#endif ++ tx_ctrl.auto_rts = regk_ser_no; ++ tx_ctrl.txd = 1; ++ tx_ctrl.auto_cts = 0; ++ /* Rx: 8 bit, no/even parity. */ ++ if (up->regi_dmain) { ++ rx_ctrl.dma_mode = 1; ++ rx_ctrl.auto_eop = 1; ++ } ++ rx_ctrl.dma_err = regk_ser_stop; ++ rx_ctrl.sampling = regk_ser_majority; ++ rx_ctrl.timeout = 1; ++ ++#ifdef CONFIG_ETRAX_RS485 ++ if (up->rs485.enabled && (up->port_type != TYPE_485FD)) { ++# ifdef CONFIG_ETRAX_RS485_DISABLE_RECEIVER ++ rx_ctrl.half_duplex = regk_ser_yes; ++# endif ++ rx_ctrl.rts_n = up->rs485.rts_after_sent ? ++ regk_ser_active : regk_ser_inactive; ++ } else if (up->port_type == TYPE_485FD) { ++ rx_ctrl.rts_n = regk_ser_active; ++ } else ++#endif ++ rx_ctrl.rts_n = regk_ser_inactive; ++ ++ /* Common for tx and rx: 8N1. */ ++ tx_ctrl.data_bits = regk_ser_bits8; ++ rx_ctrl.data_bits = regk_ser_bits8; ++ tx_ctrl.par = regk_ser_even; ++ rx_ctrl.par = regk_ser_even; ++ tx_ctrl.par_en = regk_ser_no; ++ rx_ctrl.par_en = regk_ser_no; ++ ++ tx_ctrl.stop_bits = regk_ser_bits1; ++ ++ ++ /* Change baud-rate and write it to the hardware. */ ++ ++ /* baud_clock = base_freq / (divisor*8) ++ * divisor = base_freq / (baud_clock * 8) ++ * base_freq is either: ++ * off, ext, 29.493MHz, 32.000 MHz, 32.768 MHz or 100 MHz ++ * 20.493MHz is used for standard baudrates ++ */ ++ ++ /* ++ * For the console port we keep the original baudrate here. Not very ++ * beautiful. ++ */ ++ if ((port != console_port) || old) ++ baud = uart_get_baud_rate(port, termios, old, 0, ++ port->uartclk / 8); ++ else ++ baud = console_baud; ++ ++ tx_baud_div.div = 29493000 / (8 * baud); ++ /* Rx uses same as tx. */ ++ rx_baud_div.div = tx_baud_div.div; ++ rx_ctrl.base_freq = tx_ctrl.base_freq; ++ ++ if ((termios->c_cflag & CSIZE) == CS7) { ++ /* Set 7 bit mode. */ ++ tx_ctrl.data_bits = regk_ser_bits7; ++ rx_ctrl.data_bits = regk_ser_bits7; ++ } ++ ++ if (termios->c_cflag & CSTOPB) { ++ /* Set 2 stop bit mode. */ ++ tx_ctrl.stop_bits = regk_ser_bits2; ++ } ++ ++ if (termios->c_cflag & PARENB) { ++ /* Enable parity. */ ++ tx_ctrl.par_en = regk_ser_yes; ++ rx_ctrl.par_en = regk_ser_yes; ++ } ++ ++ if (termios->c_cflag & CMSPAR) { ++ if (termios->c_cflag & PARODD) { ++ /* Set mark parity if PARODD and CMSPAR. */ ++ tx_ctrl.par = regk_ser_mark; ++ rx_ctrl.par = regk_ser_mark; ++ } else { ++ tx_ctrl.par = regk_ser_space; ++ rx_ctrl.par = regk_ser_space; ++ } ++ } else { ++ if (termios->c_cflag & PARODD) { ++ /* Set odd parity. */ ++ tx_ctrl.par = regk_ser_odd; ++ rx_ctrl.par = regk_ser_odd; ++ } ++ } ++ ++ if (termios->c_cflag & CRTSCTS) { ++ /* Enable automatic CTS handling. */ ++ tx_ctrl.auto_cts = regk_ser_yes; ++ } ++ ++ /* Make sure the tx and rx are enabled. */ ++ tx_ctrl.en = regk_ser_yes; ++ rx_ctrl.en = regk_ser_yes; ++ ++ /* ++ * Wait for tr_idle in case a character is being output, so it won't ++ * be damaged by the changes we do below. It seems the termios ++ * changes "sometimes" (we can't see e.g. a tcsetattr TCSANOW ++ * parameter here) should take place no matter what state. However, ++ * in case we should wait, we may have a non-empty transmitter state ++ * as we tell the upper layers that we're all done when we've passed ++ * characters to the hardware, but we don't wait for them being ++ * actually shifted out. ++ */ ++ spin_lock_irqsave(&port->lock, flags); ++ ++ /* ++ * None of our interrupts re-enable DMA, so it's thankfully ok to ++ * disable it once, outside the loop. ++ */ ++ tx_dma_en.en = 0; ++ REG_WR(ser, up->regi_ser, rw_tr_dma_en, tx_dma_en); ++ do { ++ /* ++ * Make sure we have integrity between the read r_stat status ++ * and us writing the registers below, but don't busy-wait ++ * with interrupts off. We need to keep the port lock though ++ * (if we go SMP), so nobody else writes characters. ++ */ ++ local_irq_restore(flags); ++ local_irq_save(flags); ++ rstat = REG_RD(ser, up->regi_ser, r_stat_din); ++ } while (!rstat.tr_idle); ++ ++ /* Actually write the control regs (if modified) to the hardware. */ ++ ++ uart_update_timeout(port, termios->c_cflag, port->uartclk/8); ++ MODIFY_REG(up->regi_ser, rw_rec_baud_div, rx_baud_div); ++ MODIFY_REG(up->regi_ser, rw_rec_ctrl, rx_ctrl); ++ ++ MODIFY_REG(up->regi_ser, rw_tr_baud_div, tx_baud_div); ++ MODIFY_REG(up->regi_ser, rw_tr_ctrl, tx_ctrl); ++ ++ tx_dma_en.en = up->regi_dmaout != 0; ++ REG_WR(ser, up->regi_ser, rw_tr_dma_en, tx_dma_en); ++ ++ xoff = REG_RD(ser, up->regi_ser, rw_xoff); ++ ++ if (up->port.info && (up->port.info->tty->termios->c_iflag & IXON)) { ++ xoff.chr = STOP_CHAR(up->port.info->tty); ++ xoff.automatic = regk_ser_yes; ++ } else ++ xoff.automatic = regk_ser_no; ++ ++ MODIFY_REG(up->regi_ser, rw_xoff, xoff); ++ ++ /* ++ * Make sure we don't start in an automatically shut-off state due to ++ * a previous early exit. ++ */ ++ xoff_clr.clr = 1; ++ REG_WR(ser, up->regi_ser, rw_xoff_clr, xoff_clr); ++ ++ serial_cris_set_mctrl(&up->port, up->port.mctrl); ++ spin_unlock_irqrestore(&up->port.lock, flags); ++} ++ ++static const char * ++serial_cris_type(struct uart_port *port) ++{ ++ return "CRISv32"; ++} ++ ++static void serial_cris_release_port(struct uart_port *port) ++{ ++} ++ ++static int serial_cris_request_port(struct uart_port *port) ++{ ++ return 0; ++} ++ ++static void serial_cris_config_port(struct uart_port *port, int flags) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ up->port.type = PORT_CRIS; ++} ++ ++#if defined(CONFIG_ETRAX_RS485) ++ ++static void cris_set_rs485_mode(struct uart_cris_port* up) { ++ reg_ser_rw_tr_ctrl tr_ctrl; ++ reg_ser_rw_rec_ctrl rec_ctrl; ++ reg_scope_instances regi_ser = up->regi_ser; ++ ++ if (up->port_type == TYPE_485FD) ++ /* We do not want to change anything if we are in 485FD mode */ ++ return; ++ ++ tr_ctrl = REG_RD(ser, regi_ser, rw_tr_ctrl); ++ rec_ctrl = REG_RD(ser, regi_ser, rw_rec_ctrl); ++ ++ /* Set port in RS-485 mode */ ++ if (up->rs485.enabled) { ++ tr_ctrl.auto_rts = regk_ser_yes; ++ rec_ctrl.rts_n = up->rs485.rts_after_sent ? ++ regk_ser_active : regk_ser_inactive; ++#ifdef CONFIG_ETRAX_RS485_DISABLE_RECEIVER ++ rec_ctrl.half_duplex = regk_ser_yes; ++#endif ++ } ++ /* Set port to RS-232 mode */ ++ else { ++ rec_ctrl.rts_n = regk_ser_inactive; ++ tr_ctrl.auto_rts = regk_ser_no; ++ rec_ctrl.half_duplex = regk_ser_no; ++ } ++ ++ REG_WR(ser, regi_ser, rw_tr_ctrl, tr_ctrl); ++ REG_WR(ser, regi_ser, rw_rec_ctrl, rec_ctrl); ++} ++ ++/* Enable/disable RS-485 mode on selected port. */ ++static int ++cris_enable_rs485(struct uart_cris_port* up, struct rs485_control *r) ++{ ++ if (up->port_type == TYPE_485FD) ++ /* Port in 485FD mode can not chage mode */ ++ goto out; ++ ++ up->rs485.enabled = 0x1 & r->enabled; ++ up->rs485.rts_on_send = 0x01 & r->rts_on_send; ++ up->rs485.rts_after_sent = 0x01 & r->rts_after_sent; ++ up->rs485.delay_rts_before_send = r->delay_rts_before_send; ++ ++ cris_set_rs485_mode(up); ++ out: ++ return 0; ++} ++ ++ ++/* Enable RS485 mode on port and send the data. Port will stay ++ * in 485 mode after the data has been sent. ++ */ ++static int ++cris_write_rs485(struct uart_cris_port* up, const unsigned char *buf, ++ int count) ++{ ++ up->rs485.enabled = 1; ++ ++ /* Set the port in RS485 mode */ ++ cris_set_rs485_mode(up); ++ ++ /* Send the data */ ++ count = serial_cris_driver.tty_driver->write(up->port.info->tty, buf, count); ++ ++ return count; ++} ++ ++#endif /* CONFIG_ETRAX_RS485 */ ++ ++static int serial_cris_ioctl(struct uart_port *port, unsigned int cmd, ++ unsigned long arg) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ ++ switch (cmd) { ++#if defined(CONFIG_ETRAX_RS485) ++ case TIOCSERSETRS485: { ++ struct rs485_control rs485ctrl; ++ if (copy_from_user(&rs485ctrl, (struct rs485_control*) arg, ++ sizeof(rs485ctrl))) ++ return -EFAULT; ++ ++ return cris_enable_rs485(up, &rs485ctrl); ++ } ++ ++ case TIOCSERWRRS485: { ++ struct rs485_write rs485wr; ++ if (copy_from_user(&rs485wr, (struct rs485_write*)arg, ++ sizeof(rs485wr))) ++ return -EFAULT; ++ ++ return cris_write_rs485(up, rs485wr.outc, rs485wr.outc_size); ++ } ++#endif ++ default: ++ return -ENOIOCTLCMD; ++ } ++ ++ return 0; ++} ++ ++static const struct uart_ops serial_cris_pops = { ++ .tx_empty = serial_cris_tx_empty, ++ .set_mctrl = serial_cris_set_mctrl, ++ .get_mctrl = serial_cris_get_mctrl, ++ .stop_tx = serial_cris_stop_tx, ++ .start_tx = serial_cris_start_tx, ++ .send_xchar = serial_cris_send_xchar, ++ .stop_rx = serial_cris_stop_rx, ++ .enable_ms = serial_cris_enable_ms, ++ .break_ctl = serial_cris_break_ctl, ++ .startup = serial_cris_startup, ++ .shutdown = serial_cris_shutdown, ++ .set_termios = serial_cris_set_termios, ++ .type = serial_cris_type, ++ .release_port = serial_cris_release_port, ++ .request_port = serial_cris_request_port, ++ .config_port = serial_cris_config_port, ++ .ioctl = serial_cris_ioctl, ++}; ++ ++/* ++ * It's too easy to break CONFIG_ETRAX_DEBUG_PORT_NULL and the ++ * no-config choices by adding and moving code to before a necessary ++ * early exit in all functions for the special case of ++ * up->regi_ser == 0. This collection of dummy functions lets us ++ * avoid that. Maybe there should be a generic table of dummy serial ++ * functions? ++ */ ++ ++static unsigned int serial_cris_tx_empty_dummy(struct uart_port *port) ++{ ++ return TIOCSER_TEMT; ++} ++ ++static void serial_cris_set_mctrl_dummy(struct uart_port *port, ++ unsigned int mctrl) ++{ ++} ++ ++static unsigned int serial_cris_get_mctrl_dummy(struct uart_port *port) ++{ ++ return 0; ++} ++ ++static void serial_cris_stop_tx_dummy(struct uart_port *port) ++{ ++} ++ ++static void serial_cris_start_tx_dummy(struct uart_port *port) ++{ ++ /* Discard outbound characters. */ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ struct circ_buf *xmit = &up->port.info->xmit; ++ xmit->tail = xmit->head; ++ uart_write_wakeup(port); ++} ++ ++#define serial_cris_stop_rx_dummy serial_cris_stop_tx_dummy ++ ++#define serial_cris_enable_ms_dummy serial_cris_stop_tx_dummy ++ ++static void serial_cris_break_ctl_dummy(struct uart_port *port, ++ int break_state) ++{ ++} ++ ++static int serial_cris_startup_dummy(struct uart_port *port) ++{ ++ return 0; ++} ++ ++#define serial_cris_shutdown_dummy serial_cris_stop_tx_dummy ++ ++static void ++serial_cris_set_termios_dummy(struct uart_port *port, struct termios *termios, ++ struct termios *old) ++{ ++} ++ ++#define serial_cris_release_port_dummy serial_cris_stop_tx_dummy ++#define serial_cris_request_port_dummy serial_cris_startup_dummy ++ ++static const struct uart_ops serial_cris_dummy_pops = { ++ /* ++ * We *could* save one or two of those with different ++ * signature by casting and knowledge of the ABI, but it's ++ * just not worth the maintenance headache. ++ * For the ones we don't define here, the default (usually meaning ++ * "unimplemented") makes sense. ++ */ ++ .tx_empty = serial_cris_tx_empty_dummy, ++ .set_mctrl = serial_cris_set_mctrl_dummy, ++ .get_mctrl = serial_cris_get_mctrl_dummy, ++ .stop_tx = serial_cris_stop_tx_dummy, ++ .start_tx = serial_cris_start_tx_dummy, ++ .stop_rx = serial_cris_stop_rx_dummy, ++ .enable_ms = serial_cris_enable_ms_dummy, ++ .break_ctl = serial_cris_break_ctl_dummy, ++ .startup = serial_cris_startup_dummy, ++ .shutdown = serial_cris_shutdown_dummy, ++ .set_termios = serial_cris_set_termios_dummy, ++ ++ /* This one we keep the same. */ ++ .type = serial_cris_type, ++ ++ .release_port = serial_cris_release_port_dummy, ++ .request_port = serial_cris_request_port_dummy, ++ ++ /* ++ * This one we keep the same too, as long as it doesn't do ++ * anything else but to set the type. ++ */ ++ .config_port = serial_cris_config_port, ++}; ++ ++static void cris_serial_port_init(struct uart_port *port, int line) ++{ ++ struct uart_cris_port *up = (struct uart_cris_port *)port; ++ static int first = 1; ++ ++ if (up->initialized) ++ return; ++ up->initialized = 1; ++ port->line = line; ++ spin_lock_init(&port->lock); ++ port->ops = ++ up->regi_ser == 0 ? &serial_cris_dummy_pops : ++ &serial_cris_pops; ++ port->irq = up->irq; ++ port->iobase = up->regi_ser ? up->regi_ser : 1; ++ port->uartclk = 29493000; ++ ++ /* ++ * We can't fit any more than 255 here (unsigned char), though ++ * actually UART_XMIT_SIZE characters could be pending output (if it ++ * wasn't for the single test in transmit_chars_dma). At time of this ++ * writing, the definition of "fifosize" is here the amount of ++ * characters that can be pending output after a start_tx call until ++ * tx_empty returns 1: see serial_core.c:uart_wait_until_sent. This ++ * matters for timeout calculations unfortunately, but keeping larger ++ * amounts at the DMA wouldn't win much so let's just play nice. ++ */ ++ port->fifosize = 255; ++ port->flags = UPF_BOOT_AUTOCONF; ++ ++#ifdef CONFIG_ETRAX_RS485 ++ /* Set sane defaults. */ ++ up->rs485.rts_on_send = 0; ++ up->rs485.rts_after_sent = 1; ++ up->rs485.delay_rts_before_send = 0; ++ if (up->port_type > TYPE_232) ++ up->rs485.enabled = 1; ++ else ++ up->rs485.enabled = 0; ++#endif ++ ++ if (first) { ++ first = 0; ++#ifdef CONFIG_ETRAX_SERIAL_PORT0 ++ SETUP_PINS(0); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT1 ++ SETUP_PINS(1); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT2 ++ SETUP_PINS(2); ++#endif ++#ifdef CONFIG_ETRAX_SERIAL_PORT3 ++ SETUP_PINS(3); ++#endif ++ } ++} ++ ++static int __init serial_cris_init(void) ++{ ++ int ret, i; ++ reg_ser_rw_rec_ctrl rec_ctrl; ++ printk(KERN_INFO "Serial: CRISv32 driver $Revision: 1.78 $ "); ++ ++ ret = uart_register_driver(&serial_cris_driver); ++ if (ret) ++ goto out; ++ ++ for (i = 0; i < UART_NR; i++) { ++ if (serial_cris_ports[i].used) { ++#ifdef CONFIG_ETRAX_RS485 ++ /* Make sure that the RTS pin stays low when allocating ++ * pins for a port in 485 mode. ++ */ ++ if (serial_cris_ports[i].port_type > TYPE_232) { ++ rec_ctrl = REG_RD(ser, serial_cris_ports[i].regi_ser, rw_rec_ctrl); ++ rec_ctrl.rts_n = regk_ser_active; ++ REG_WR(ser, serial_cris_ports[i].regi_ser, rw_rec_ctrl, rec_ctrl); ++ } ++#endif ++ switch (serial_cris_ports[i].regi_ser) { ++ case regi_ser1: ++ if (crisv32_pinmux_alloc_fixed(pinmux_ser1)) { ++ printk("Failed to allocate pins for ser1, disable port\n"); ++ serial_cris_ports[i].used = 0; ++ continue; ++ } ++ break; ++ case regi_ser2: ++ if (crisv32_pinmux_alloc_fixed(pinmux_ser2)) { ++ printk("Failed to allocate pins for ser2, disable port\n"); ++ serial_cris_ports[i].used = 0; ++ continue; ++ } ++ break; ++ case regi_ser3: ++ if (crisv32_pinmux_alloc_fixed(pinmux_ser3)) { ++ printk("Failed to allocate pins for ser3, disable port\n"); ++ serial_cris_ports[i].used = 0; ++ continue; ++ } ++ break; ++ } ++ ++ struct uart_port *port = &serial_cris_ports[i].port; ++ cris_console.index = i; ++ cris_serial_port_init(port, i); ++ uart_add_one_port(&serial_cris_driver, port); ++ } ++ } ++ ++out: ++ return ret; ++} ++ ++static void __exit serial_cris_exit(void) ++{ ++ int i; ++ for (i = 0; i < UART_NR; i++) ++ if (serial_cris_ports[i].used) { ++ switch (serial_cris_ports[i].regi_ser) { ++ case regi_ser1: ++ crisv32_pinmux_dealloc_fixed(pinmux_ser1); ++ break; ++ case regi_ser2: ++ crisv32_pinmux_dealloc_fixed(pinmux_ser2); ++ break; ++ case regi_ser3: ++ crisv32_pinmux_dealloc_fixed(pinmux_ser3); ++ break; ++ } ++ uart_remove_one_port(&serial_cris_driver, ++ &serial_cris_ports[i].port); ++ } ++ uart_unregister_driver(&serial_cris_driver); ++} ++ ++module_init(serial_cris_init); ++module_exit(serial_cris_exit); +--- linux-2.6.19.2.orig/drivers/usb/host/hc_crisv10.c 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/usb/host/hc-crisv10.c 2007-02-26 20:58:29.000000000 +0100 +@@ -1,219 +1,51 @@ + /* +- * usb-host.c: ETRAX 100LX USB Host Controller Driver (HCD) + * +- * Copyright (c) 2002, 2003 Axis Communications AB. ++ * ETRAX 100LX USB Host Controller Driver ++ * ++ * Copyright (C) 2005, 2006 Axis Communications AB ++ * ++ * Author: Konrad Eriksson <konrad.eriksson@axis.se> ++ * + */ + ++#include <linux/module.h> + #include <linux/kernel.h> +-#include <linux/delay.h> +-#include <linux/ioport.h> +-#include <linux/sched.h> +-#include <linux/slab.h> +-#include <linux/errno.h> +-#include <linux/unistd.h> +-#include <linux/interrupt.h> + #include <linux/init.h> +-#include <linux/list.h> ++#include <linux/moduleparam.h> + #include <linux/spinlock.h> ++#include <linux/usb.h> ++#include <linux/platform_device.h> + +-#include <asm/uaccess.h> + #include <asm/io.h> + #include <asm/irq.h> +-#include <asm/dma.h> +-#include <asm/system.h> +-#include <asm/arch/svinto.h> ++#include <asm/arch/dma.h> ++#include <asm/arch/io_interface_mux.h> + +-#include <linux/usb.h> +-/* Ugly include because we don't live with the other host drivers. */ +-#include <../drivers/usb/core/hcd.h> +-#include <../drivers/usb/core/usb.h> +- +-#include "hc_crisv10.h" ++#include "../core/hcd.h" ++#include "../core/hub.h" ++#include "hc-crisv10.h" ++#include "hc-cris-dbg.h" ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Host Controller settings */ ++/***************************************************************************/ ++/***************************************************************************/ ++ ++#define VERSION "1.00" ++#define COPYRIGHT "(c) 2005, 2006 Axis Communications AB" ++#define DESCRIPTION "ETRAX 100LX USB Host Controller" + + #define ETRAX_USB_HC_IRQ USB_HC_IRQ_NBR + #define ETRAX_USB_RX_IRQ USB_DMA_RX_IRQ_NBR + #define ETRAX_USB_TX_IRQ USB_DMA_TX_IRQ_NBR + +-static const char *usb_hcd_version = "$Revision: 1.2 $"; +- +-#undef KERN_DEBUG +-#define KERN_DEBUG "" +- +- +-#undef USB_DEBUG_RH +-#undef USB_DEBUG_EPID +-#undef USB_DEBUG_SB +-#undef USB_DEBUG_DESC +-#undef USB_DEBUG_URB +-#undef USB_DEBUG_TRACE +-#undef USB_DEBUG_BULK +-#undef USB_DEBUG_CTRL +-#undef USB_DEBUG_INTR +-#undef USB_DEBUG_ISOC +- +-#ifdef USB_DEBUG_RH +-#define dbg_rh(format, arg...) printk(KERN_DEBUG __FILE__ ": (RH) " format "\n" , ## arg) +-#else +-#define dbg_rh(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_EPID +-#define dbg_epid(format, arg...) printk(KERN_DEBUG __FILE__ ": (EPID) " format "\n" , ## arg) +-#else +-#define dbg_epid(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_SB +-#define dbg_sb(format, arg...) printk(KERN_DEBUG __FILE__ ": (SB) " format "\n" , ## arg) +-#else +-#define dbg_sb(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_CTRL +-#define dbg_ctrl(format, arg...) printk(KERN_DEBUG __FILE__ ": (CTRL) " format "\n" , ## arg) +-#else +-#define dbg_ctrl(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_BULK +-#define dbg_bulk(format, arg...) printk(KERN_DEBUG __FILE__ ": (BULK) " format "\n" , ## arg) +-#else +-#define dbg_bulk(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_INTR +-#define dbg_intr(format, arg...) printk(KERN_DEBUG __FILE__ ": (INTR) " format "\n" , ## arg) +-#else +-#define dbg_intr(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_ISOC +-#define dbg_isoc(format, arg...) printk(KERN_DEBUG __FILE__ ": (ISOC) " format "\n" , ## arg) +-#else +-#define dbg_isoc(format, arg...) do {} while (0) +-#endif +- +-#ifdef USB_DEBUG_TRACE +-#define DBFENTER (printk(": Entering: %s\n", __FUNCTION__)) +-#define DBFEXIT (printk(": Exiting: %s\n", __FUNCTION__)) +-#else +-#define DBFENTER do {} while (0) +-#define DBFEXIT do {} while (0) +-#endif +- +-#define usb_pipeslow(pipe) (((pipe) >> 26) & 1) +- +-/*------------------------------------------------------------------- +- Virtual Root Hub +- -------------------------------------------------------------------*/ +- +-static __u8 root_hub_dev_des[] = +-{ +- 0x12, /* __u8 bLength; */ +- 0x01, /* __u8 bDescriptorType; Device */ +- 0x00, /* __le16 bcdUSB; v1.0 */ +- 0x01, +- 0x09, /* __u8 bDeviceClass; HUB_CLASSCODE */ +- 0x00, /* __u8 bDeviceSubClass; */ +- 0x00, /* __u8 bDeviceProtocol; */ +- 0x08, /* __u8 bMaxPacketSize0; 8 Bytes */ +- 0x00, /* __le16 idVendor; */ +- 0x00, +- 0x00, /* __le16 idProduct; */ +- 0x00, +- 0x00, /* __le16 bcdDevice; */ +- 0x00, +- 0x00, /* __u8 iManufacturer; */ +- 0x02, /* __u8 iProduct; */ +- 0x01, /* __u8 iSerialNumber; */ +- 0x01 /* __u8 bNumConfigurations; */ +-}; +- +-/* Configuration descriptor */ +-static __u8 root_hub_config_des[] = +-{ +- 0x09, /* __u8 bLength; */ +- 0x02, /* __u8 bDescriptorType; Configuration */ +- 0x19, /* __le16 wTotalLength; */ +- 0x00, +- 0x01, /* __u8 bNumInterfaces; */ +- 0x01, /* __u8 bConfigurationValue; */ +- 0x00, /* __u8 iConfiguration; */ +- 0x40, /* __u8 bmAttributes; Bit 7: Bus-powered */ +- 0x00, /* __u8 MaxPower; */ +- +- /* interface */ +- 0x09, /* __u8 if_bLength; */ +- 0x04, /* __u8 if_bDescriptorType; Interface */ +- 0x00, /* __u8 if_bInterfaceNumber; */ +- 0x00, /* __u8 if_bAlternateSetting; */ +- 0x01, /* __u8 if_bNumEndpoints; */ +- 0x09, /* __u8 if_bInterfaceClass; HUB_CLASSCODE */ +- 0x00, /* __u8 if_bInterfaceSubClass; */ +- 0x00, /* __u8 if_bInterfaceProtocol; */ +- 0x00, /* __u8 if_iInterface; */ +- +- /* endpoint */ +- 0x07, /* __u8 ep_bLength; */ +- 0x05, /* __u8 ep_bDescriptorType; Endpoint */ +- 0x81, /* __u8 ep_bEndpointAddress; IN Endpoint 1 */ +- 0x03, /* __u8 ep_bmAttributes; Interrupt */ +- 0x08, /* __le16 ep_wMaxPacketSize; 8 Bytes */ +- 0x00, +- 0xff /* __u8 ep_bInterval; 255 ms */ +-}; +- +-static __u8 root_hub_hub_des[] = +-{ +- 0x09, /* __u8 bLength; */ +- 0x29, /* __u8 bDescriptorType; Hub-descriptor */ +- 0x02, /* __u8 bNbrPorts; */ +- 0x00, /* __u16 wHubCharacteristics; */ +- 0x00, +- 0x01, /* __u8 bPwrOn2pwrGood; 2ms */ +- 0x00, /* __u8 bHubContrCurrent; 0 mA */ +- 0x00, /* __u8 DeviceRemovable; *** 7 Ports max *** */ +- 0xff /* __u8 PortPwrCtrlMask; *** 7 ports max *** */ +-}; +- +-static DEFINE_TIMER(bulk_start_timer, NULL, 0, 0); +-static DEFINE_TIMER(bulk_eot_timer, NULL, 0, 0); +- +-/* We want the start timer to expire before the eot timer, because the former might start +- traffic, thus making it unnecessary for the latter to time out. */ +-#define BULK_START_TIMER_INTERVAL (HZ/10) /* 100 ms */ +-#define BULK_EOT_TIMER_INTERVAL (HZ/10+2) /* 120 ms */ +- +-#define OK(x) len = (x); dbg_rh("OK(%d): line: %d", x, __LINE__); break +-#define CHECK_ALIGN(x) if (((__u32)(x)) & 0x00000003) \ +-{panic("Alignment check (DWORD) failed at %s:%s:%d\n", __FILE__, __FUNCTION__, __LINE__);} +- +-#define SLAB_FLAG (in_interrupt() ? SLAB_ATOMIC : SLAB_KERNEL) +-#define KMALLOC_FLAG (in_interrupt() ? GFP_ATOMIC : GFP_KERNEL) +- +-/* Most helpful debugging aid */ +-#define assert(expr) ((void) ((expr) ? 0 : (err("assert failed at line %d",__LINE__)))) +- +-/* Alternative assert define which stops after a failed assert. */ +-/* +-#define assert(expr) \ +-{ \ +- if (!(expr)) { \ +- err("assert failed at line %d",__LINE__); \ +- while (1); \ +- } \ +-} +-*/ +- ++/* Number of physical ports in Etrax 100LX */ ++#define USB_ROOT_HUB_PORTS 2 + +-/* FIXME: Should RX_BUF_SIZE be a config option, or maybe we should adjust it dynamically? +- To adjust it dynamically we would have to get an interrupt when we reach the end +- of the rx descriptor list, or when we get close to the end, and then allocate more +- descriptors. */ +- +-#define NBR_OF_RX_DESC 512 +-#define RX_DESC_BUF_SIZE 1024 +-#define RX_BUF_SIZE (NBR_OF_RX_DESC * RX_DESC_BUF_SIZE) ++const char hc_name[] = "hc-crisv10"; ++const char product_desc[] = DESCRIPTION; + + /* The number of epids is, among other things, used for pre-allocating + ctrl, bulk and isoc EP descriptors (one for each epid). +@@ -221,4332 +53,4632 @@ + #define NBR_OF_EPIDS 32 + + /* Support interrupt traffic intervals up to 128 ms. */ +-#define MAX_INTR_INTERVAL 128 ++#define MAX_INTR_INTERVAL 128 + +-/* If periodic traffic (intr or isoc) is to be used, then one entry in the EP table +- must be "invalid". By this we mean that we shouldn't care about epid attentions +- for this epid, or at least handle them differently from epid attentions for "valid" +- epids. This define determines which one to use (don't change it). */ +-#define INVALID_EPID 31 ++/* If periodic traffic (intr or isoc) is to be used, then one entry in the EP ++ table must be "invalid". By this we mean that we shouldn't care about epid ++ attentions for this epid, or at least handle them differently from epid ++ attentions for "valid" epids. This define determines which one to use ++ (don't change it). */ ++#define INVALID_EPID 31 + /* A special epid for the bulk dummys. */ +-#define DUMMY_EPID 30 +- +-/* This is just a software cache for the valid entries in R_USB_EPT_DATA. */ +-static __u32 epid_usage_bitmask; +- +-/* A bitfield to keep information on in/out traffic is needed to uniquely identify +- an endpoint on a device, since the most significant bit which indicates traffic +- direction is lacking in the ep_id field (ETRAX epids can handle both in and +- out traffic on endpoints that are otherwise identical). The USB framework, however, +- relies on them to be handled separately. For example, bulk IN and OUT urbs cannot +- be queued in the same list, since they would block each other. */ +-static __u32 epid_out_traffic; +- +-/* DMA IN cache bug. Align the DMA IN buffers to 32 bytes, i.e. a cache line. +- Since RX_DESC_BUF_SIZE is 1024 is a multiple of 32, all rx buffers will be cache aligned. */ +-static volatile unsigned char RxBuf[RX_BUF_SIZE] __attribute__ ((aligned (32))); +-static volatile USB_IN_Desc_t RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned (4))); +- +-/* Pointers into RxDescList. */ +-static volatile USB_IN_Desc_t *myNextRxDesc; +-static volatile USB_IN_Desc_t *myLastRxDesc; +-static volatile USB_IN_Desc_t *myPrevRxDesc; +- +-/* EP descriptors must be 32-bit aligned. */ +-static volatile USB_EP_Desc_t TxCtrlEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); +-static volatile USB_EP_Desc_t TxBulkEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); +-/* After each enabled bulk EP (IN or OUT) we put two disabled EP descriptors with the eol flag set, +- causing the DMA to stop the DMA channel. The first of these two has the intr flag set, which +- gives us a dma8_sub0_descr interrupt. When we receive this, we advance the DMA one step in the +- EP list and then restart the bulk channel, thus forcing a switch between bulk EP descriptors +- in each frame. */ +-static volatile USB_EP_Desc_t TxBulkDummyEPList[NBR_OF_EPIDS][2] __attribute__ ((aligned (4))); +- +-static volatile USB_EP_Desc_t TxIsocEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); +-static volatile USB_SB_Desc_t TxIsocSB_zout __attribute__ ((aligned (4))); +- +-static volatile USB_EP_Desc_t TxIntrEPList[MAX_INTR_INTERVAL] __attribute__ ((aligned (4))); +-static volatile USB_SB_Desc_t TxIntrSB_zout __attribute__ ((aligned (4))); +- +-/* A zout transfer makes a memory access at the address of its buf pointer, which means that setting +- this buf pointer to 0 will cause an access to the flash. In addition to this, setting sw_len to 0 +- results in a 16/32 bytes (depending on DMA burst size) transfer. Instead, we set it to 1, and point +- it to this buffer. */ +-static int zout_buffer[4] __attribute__ ((aligned (4))); ++#define DUMMY_EPID 30 + +-/* Cache for allocating new EP and SB descriptors. */ +-static kmem_cache_t *usb_desc_cache; ++/* Module settings */ + +-/* Cache for the registers allocated in the top half. */ +-static kmem_cache_t *top_half_reg_cache; ++MODULE_DESCRIPTION(DESCRIPTION); ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Konrad Eriksson <konrad.eriksson@axis.se>"); + +-/* Cache for the data allocated in the isoc descr top half. */ +-static kmem_cache_t *isoc_compl_cache; + +-static struct usb_bus *etrax_usb_bus; ++/* Module parameters */ + +-/* This is a circular (double-linked) list of the active urbs for each epid. +- The head is never removed, and new urbs are linked onto the list as +- urb_entry_t elements. Don't reference urb_list directly; use the wrapper +- functions instead. Note that working with these lists might require spinlock +- protection. */ +-static struct list_head urb_list[NBR_OF_EPIDS]; ++/* 0 = No ports enabled ++ 1 = Only port 1 enabled (on board ethernet on devboard) ++ 2 = Only port 2 enabled (external connector on devboard) ++ 3 = Both ports enabled ++*/ ++static unsigned int ports = 3; ++module_param(ports, uint, S_IRUGO); ++MODULE_PARM_DESC(ports, "Bitmask indicating USB ports to use"); + +-/* Read about the need and usage of this lock in submit_ctrl_urb. */ +-static spinlock_t urb_list_lock; + +-/* Used when unlinking asynchronously. */ +-static struct list_head urb_unlink_list; ++/***************************************************************************/ ++/***************************************************************************/ ++/* Shared global variables for this module */ ++/***************************************************************************/ ++/***************************************************************************/ + +-/* for returning string descriptors in UTF-16LE */ +-static int ascii2utf (char *ascii, __u8 *utf, int utfmax) +-{ +- int retval; ++/* EP descriptor lists for non period transfers. Must be 32-bit aligned. */ ++static volatile struct USB_EP_Desc TxBulkEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); + +- for (retval = 0; *ascii && utfmax > 1; utfmax -= 2, retval += 2) { +- *utf++ = *ascii++ & 0x7f; +- *utf++ = 0; +- } +- return retval; +-} ++static volatile struct USB_EP_Desc TxCtrlEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); + +-static int usb_root_hub_string (int id, int serial, char *type, __u8 *data, int len) +-{ +- char buf [30]; ++/* EP descriptor lists for period transfers. Must be 32-bit aligned. */ ++static volatile struct USB_EP_Desc TxIntrEPList[MAX_INTR_INTERVAL] __attribute__ ((aligned (4))); ++static volatile struct USB_SB_Desc TxIntrSB_zout __attribute__ ((aligned (4))); + +- // assert (len > (2 * (sizeof (buf) + 1))); +- // assert (strlen (type) <= 8); ++static volatile struct USB_EP_Desc TxIsocEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); ++static volatile struct USB_SB_Desc TxIsocSB_zout __attribute__ ((aligned (4))); + +- // language ids +- if (id == 0) { +- *data++ = 4; *data++ = 3; /* 4 bytes data */ +- *data++ = 0; *data++ = 0; /* some language id */ +- return 4; +- +- // serial number +- } else if (id == 1) { +- sprintf (buf, "%x", serial); +- +- // product description +- } else if (id == 2) { +- sprintf (buf, "USB %s Root Hub", type); +- +- // id 3 == vendor description +- +- // unsupported IDs --> "stall" +- } else +- return 0; +- +- data [0] = 2 + ascii2utf (buf, data + 2, len - 2); +- data [1] = 3; +- return data [0]; +-} ++static volatile struct USB_SB_Desc TxIsocSBList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); + +-/* Wrappers around the list functions (include/linux/list.h). */ ++/* After each enabled bulk EP IN we put two disabled EP descriptors with the eol flag set, ++ causing the DMA to stop the DMA channel. The first of these two has the intr flag set, which ++ gives us a dma8_sub0_descr interrupt. When we receive this, we advance the DMA one step in the ++ EP list and then restart the bulk channel, thus forcing a switch between bulk EP descriptors ++ in each frame. */ ++static volatile struct USB_EP_Desc TxBulkDummyEPList[NBR_OF_EPIDS][2] __attribute__ ((aligned (4))); + +-static inline int urb_list_empty(int epid) ++/* List of URB pointers, where each points to the active URB for a epid. ++ For Bulk, Ctrl and Intr this means which URB that currently is added to ++ DMA lists (Isoc URBs are all directly added to DMA lists). As soon as ++ URB has completed is the queue examined and the first URB in queue is ++ removed and moved to the activeUrbList while its state change to STARTED and ++ its transfer(s) gets added to DMA list (exception Isoc where URBs enter ++ state STARTED directly and added transfers added to DMA lists). */ ++static struct urb *activeUrbList[NBR_OF_EPIDS]; ++ ++/* Additional software state info for each epid */ ++static struct etrax_epid epid_state[NBR_OF_EPIDS]; ++ ++/* Timer handles for bulk traffic timer used to avoid DMA bug where DMA stops ++ even if there is new data waiting to be processed */ ++static struct timer_list bulk_start_timer = TIMER_INITIALIZER(NULL, 0, 0); ++static struct timer_list bulk_eot_timer = TIMER_INITIALIZER(NULL, 0, 0); ++ ++/* We want the start timer to expire before the eot timer, because the former ++ might start traffic, thus making it unnecessary for the latter to time ++ out. */ ++#define BULK_START_TIMER_INTERVAL (HZ/50) /* 20 ms */ ++#define BULK_EOT_TIMER_INTERVAL (HZ/16) /* 60 ms */ ++ ++/* Delay before a URB completion happen when it's scheduled to be delayed */ ++#define LATER_TIMER_DELAY (HZ/50) /* 20 ms */ ++ ++/* Simplifying macros for checking software state info of a epid */ ++/* ----------------------------------------------------------------------- */ ++#define epid_inuse(epid) epid_state[epid].inuse ++#define epid_out_traffic(epid) epid_state[epid].out_traffic ++#define epid_isoc(epid) (epid_state[epid].type == PIPE_ISOCHRONOUS ? 1 : 0) ++#define epid_intr(epid) (epid_state[epid].type == PIPE_INTERRUPT ? 1 : 0) ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* DEBUG FUNCTIONS */ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Note that these functions are always available in their "__" variants, ++ for use in error situations. The "__" missing variants are controlled by ++ the USB_DEBUG_DESC/USB_DEBUG_URB macros. */ ++static void __dump_urb(struct urb* purb) + { +- return list_empty(&urb_list[epid]); ++ struct crisv10_urb_priv *urb_priv = purb->hcpriv; ++ int urb_num = -1; ++ if(urb_priv) { ++ urb_num = urb_priv->urb_num; ++ } ++ printk("\nURB:0x%x[%d]\n", (unsigned int)purb, urb_num); ++ printk("dev :0x%08lx\n", (unsigned long)purb->dev); ++ printk("pipe :0x%08x\n", purb->pipe); ++ printk("status :%d\n", purb->status); ++ printk("transfer_flags :0x%08x\n", purb->transfer_flags); ++ printk("transfer_buffer :0x%08lx\n", (unsigned long)purb->transfer_buffer); ++ printk("transfer_buffer_length:%d\n", purb->transfer_buffer_length); ++ printk("actual_length :%d\n", purb->actual_length); ++ printk("setup_packet :0x%08lx\n", (unsigned long)purb->setup_packet); ++ printk("start_frame :%d\n", purb->start_frame); ++ printk("number_of_packets :%d\n", purb->number_of_packets); ++ printk("interval :%d\n", purb->interval); ++ printk("error_count :%d\n", purb->error_count); ++ printk("context :0x%08lx\n", (unsigned long)purb->context); ++ printk("complete :0x%08lx\n\n", (unsigned long)purb->complete); ++} ++ ++static void __dump_in_desc(volatile struct USB_IN_Desc *in) ++{ ++ printk("\nUSB_IN_Desc at 0x%08lx\n", (unsigned long)in); ++ printk(" sw_len : 0x%04x (%d)\n", in->sw_len, in->sw_len); ++ printk(" command : 0x%04x\n", in->command); ++ printk(" next : 0x%08lx\n", in->next); ++ printk(" buf : 0x%08lx\n", in->buf); ++ printk(" hw_len : 0x%04x (%d)\n", in->hw_len, in->hw_len); ++ printk(" status : 0x%04x\n\n", in->status); ++} ++ ++static void __dump_sb_desc(volatile struct USB_SB_Desc *sb) ++{ ++ char tt = (sb->command & 0x30) >> 4; ++ char *tt_string; ++ ++ switch (tt) { ++ case 0: ++ tt_string = "zout"; ++ break; ++ case 1: ++ tt_string = "in"; ++ break; ++ case 2: ++ tt_string = "out"; ++ break; ++ case 3: ++ tt_string = "setup"; ++ break; ++ default: ++ tt_string = "unknown (weird)"; ++ } ++ ++ printk(" USB_SB_Desc at 0x%08lx ", (unsigned long)sb); ++ printk(" command:0x%04x (", sb->command); ++ printk("rem:%d ", (sb->command & 0x3f00) >> 8); ++ printk("full:%d ", (sb->command & 0x40) >> 6); ++ printk("tt:%d(%s) ", tt, tt_string); ++ printk("intr:%d ", (sb->command & 0x8) >> 3); ++ printk("eot:%d ", (sb->command & 0x2) >> 1); ++ printk("eol:%d)", sb->command & 0x1); ++ printk(" sw_len:0x%04x(%d)", sb->sw_len, sb->sw_len); ++ printk(" next:0x%08lx", sb->next); ++ printk(" buf:0x%08lx\n", sb->buf); ++} ++ ++ ++static void __dump_ep_desc(volatile struct USB_EP_Desc *ep) ++{ ++ printk("USB_EP_Desc at 0x%08lx ", (unsigned long)ep); ++ printk(" command:0x%04x (", ep->command); ++ printk("ep_id:%d ", (ep->command & 0x1f00) >> 8); ++ printk("enable:%d ", (ep->command & 0x10) >> 4); ++ printk("intr:%d ", (ep->command & 0x8) >> 3); ++ printk("eof:%d ", (ep->command & 0x2) >> 1); ++ printk("eol:%d)", ep->command & 0x1); ++ printk(" hw_len:0x%04x(%d)", ep->hw_len, ep->hw_len); ++ printk(" next:0x%08lx", ep->next); ++ printk(" sub:0x%08lx\n", ep->sub); + } + +-/* Returns first urb for this epid, or NULL if list is empty. */ +-static inline struct urb *urb_list_first(int epid) ++static inline void __dump_ep_list(int pipe_type) + { +- struct urb *first_urb = 0; ++ volatile struct USB_EP_Desc *ep; ++ volatile struct USB_EP_Desc *first_ep; ++ volatile struct USB_SB_Desc *sb; ++ ++ switch (pipe_type) ++ { ++ case PIPE_BULK: ++ first_ep = &TxBulkEPList[0]; ++ break; ++ case PIPE_CONTROL: ++ first_ep = &TxCtrlEPList[0]; ++ break; ++ case PIPE_INTERRUPT: ++ first_ep = &TxIntrEPList[0]; ++ break; ++ case PIPE_ISOCHRONOUS: ++ first_ep = &TxIsocEPList[0]; ++ break; ++ default: ++ warn("Cannot dump unknown traffic type"); ++ return; ++ } ++ ep = first_ep; ++ ++ printk("\n\nDumping EP list...\n\n"); ++ ++ do { ++ __dump_ep_desc(ep); ++ /* Cannot phys_to_virt on 0 as it turns into 80000000, which is != 0. */ ++ sb = ep->sub ? phys_to_virt(ep->sub) : 0; ++ while (sb) { ++ __dump_sb_desc(sb); ++ sb = sb->next ? phys_to_virt(sb->next) : 0; ++ } ++ ep = (volatile struct USB_EP_Desc *)(phys_to_virt(ep->next)); + +- if (!urb_list_empty(epid)) { +- /* Get the first urb (i.e. head->next). */ +- urb_entry_t *urb_entry = list_entry((&urb_list[epid])->next, urb_entry_t, list); +- first_urb = urb_entry->urb; +- } +- return first_urb; ++ } while (ep != first_ep); + } + +-/* Adds an urb_entry last in the list for this epid. */ +-static inline void urb_list_add(struct urb *urb, int epid) ++static inline void __dump_ept_data(int epid) + { +- urb_entry_t *urb_entry = (urb_entry_t *)kmalloc(sizeof(urb_entry_t), KMALLOC_FLAG); +- assert(urb_entry); ++ unsigned long flags; ++ __u32 r_usb_ept_data; + +- urb_entry->urb = urb; +- list_add_tail(&urb_entry->list, &urb_list[epid]); ++ if (epid < 0 || epid > 31) { ++ printk("Cannot dump ept data for invalid epid %d\n", epid); ++ return; ++ } ++ ++ local_irq_save(flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ r_usb_ept_data = *R_USB_EPT_DATA; ++ local_irq_restore(flags); ++ ++ printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", r_usb_ept_data, epid); ++ if (r_usb_ept_data == 0) { ++ /* No need for more detailed printing. */ ++ return; ++ } ++ printk(" valid : %d\n", (r_usb_ept_data & 0x80000000) >> 31); ++ printk(" hold : %d\n", (r_usb_ept_data & 0x40000000) >> 30); ++ printk(" error_count_in : %d\n", (r_usb_ept_data & 0x30000000) >> 28); ++ printk(" t_in : %d\n", (r_usb_ept_data & 0x08000000) >> 27); ++ printk(" low_speed : %d\n", (r_usb_ept_data & 0x04000000) >> 26); ++ printk(" port : %d\n", (r_usb_ept_data & 0x03000000) >> 24); ++ printk(" error_code : %d\n", (r_usb_ept_data & 0x00c00000) >> 22); ++ printk(" t_out : %d\n", (r_usb_ept_data & 0x00200000) >> 21); ++ printk(" error_count_out : %d\n", (r_usb_ept_data & 0x00180000) >> 19); ++ printk(" max_len : %d\n", (r_usb_ept_data & 0x0003f800) >> 11); ++ printk(" ep : %d\n", (r_usb_ept_data & 0x00000780) >> 7); ++ printk(" dev : %d\n", (r_usb_ept_data & 0x0000003f)); ++} ++ ++static inline void __dump_ept_data_iso(int epid) ++{ ++ unsigned long flags; ++ __u32 ept_data; ++ ++ if (epid < 0 || epid > 31) { ++ printk("Cannot dump ept data for invalid epid %d\n", epid); ++ return; ++ } ++ ++ local_irq_save(flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ ept_data = *R_USB_EPT_DATA_ISO; ++ local_irq_restore(flags); ++ ++ printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", ept_data, epid); ++ if (ept_data == 0) { ++ /* No need for more detailed printing. */ ++ return; ++ } ++ printk(" valid : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, valid, ++ ept_data)); ++ printk(" port : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, port, ++ ept_data)); ++ printk(" error_code : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, ++ ept_data)); ++ printk(" max_len : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, max_len, ++ ept_data)); ++ printk(" ep : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, ep, ++ ept_data)); ++ printk(" dev : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, dev, ++ ept_data)); + } + +-/* Search through the list for an element that contains this urb. (The list +- is expected to be short and the one we are about to delete will often be +- the first in the list.) */ +-static inline urb_entry_t *__urb_list_entry(struct urb *urb, int epid) ++static inline void __dump_ept_data_list(void) + { +- struct list_head *entry; +- struct list_head *tmp; +- urb_entry_t *urb_entry; +- +- list_for_each_safe(entry, tmp, &urb_list[epid]) { +- urb_entry = list_entry(entry, urb_entry_t, list); +- assert(urb_entry); +- assert(urb_entry->urb); +- +- if (urb_entry->urb == urb) { +- return urb_entry; +- } +- } +- return 0; +-} ++ int i; + +-/* Delete an urb from the list. */ +-static inline void urb_list_del(struct urb *urb, int epid) +-{ +- urb_entry_t *urb_entry = __urb_list_entry(urb, epid); +- assert(urb_entry); ++ printk("Dumping the whole R_USB_EPT_DATA list\n"); + +- /* Delete entry and free. */ +- list_del(&urb_entry->list); +- kfree(urb_entry); ++ for (i = 0; i < 32; i++) { ++ __dump_ept_data(i); ++ } ++} ++ ++static void debug_epid(int epid) { ++ int i; ++ ++ if(epid_isoc(epid)) { ++ __dump_ept_data_iso(epid); ++ } else { ++ __dump_ept_data(epid); ++ } ++ ++ printk("Bulk:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxBulkEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxBulkEPList[i])); ++ } ++ } ++ ++ printk("Ctrl:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxCtrlEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxCtrlEPList[i])); ++ } ++ } ++ ++ printk("Intr:\n"); ++ for(i = 0; i < MAX_INTR_INTERVAL; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxIntrEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxIntrEPList[i])); ++ } ++ } ++ ++ printk("Isoc:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxIsocEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxIsocEPList[i])); ++ } ++ } ++ ++ __dump_ept_data_list(); ++ __dump_ep_list(PIPE_INTERRUPT); ++ printk("\n\n"); ++} ++ ++ ++ ++char* hcd_status_to_str(__u8 bUsbStatus) { ++ static char hcd_status_str[128]; ++ hcd_status_str[0] = '\0'; ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, ourun, yes)) { ++ strcat(hcd_status_str, "ourun "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, perror, yes)) { ++ strcat(hcd_status_str, "perror "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, device_mode, yes)) { ++ strcat(hcd_status_str, "device_mode "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, host_mode, yes)) { ++ strcat(hcd_status_str, "host_mode "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, started, yes)) { ++ strcat(hcd_status_str, "started "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, running, yes)) { ++ strcat(hcd_status_str, "running "); ++ } ++ return hcd_status_str; ++} ++ ++ ++char* sblist_to_str(struct USB_SB_Desc* sb_desc) { ++ static char sblist_to_str_buff[128]; ++ char tmp[32], tmp2[32]; ++ sblist_to_str_buff[0] = '\0'; ++ while(sb_desc != NULL) { ++ switch(IO_EXTRACT(USB_SB_command, tt, sb_desc->command)) { ++ case 0: sprintf(tmp, "zout"); break; ++ case 1: sprintf(tmp, "in"); break; ++ case 2: sprintf(tmp, "out"); break; ++ case 3: sprintf(tmp, "setup"); break; ++ } ++ sprintf(tmp2, "(%s %d)", tmp, sb_desc->sw_len); ++ strcat(sblist_to_str_buff, tmp2); ++ if(sb_desc->next != 0) { ++ sb_desc = phys_to_virt(sb_desc->next); ++ } else { ++ sb_desc = NULL; ++ } ++ } ++ return sblist_to_str_buff; ++} ++ ++char* port_status_to_str(__u16 wPortStatus) { ++ static char port_status_str[128]; ++ port_status_str[0] = '\0'; ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) { ++ strcat(port_status_str, "connected "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) { ++ strcat(port_status_str, "enabled "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, suspended, yes)) { ++ strcat(port_status_str, "suspended "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, reset, yes)) { ++ strcat(port_status_str, "reset "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, speed, full)) { ++ strcat(port_status_str, "full-speed "); ++ } else { ++ strcat(port_status_str, "low-speed "); ++ } ++ return port_status_str; ++} ++ ++ ++char* endpoint_to_str(struct usb_endpoint_descriptor *ed) { ++ static char endpoint_to_str_buff[128]; ++ char tmp[32]; ++ int epnum = ed->bEndpointAddress & 0x0F; ++ int dir = ed->bEndpointAddress & 0x80; ++ int type = ed->bmAttributes & 0x03; ++ endpoint_to_str_buff[0] = '\0'; ++ sprintf(endpoint_to_str_buff, "ep:%d ", epnum); ++ switch(type) { ++ case 0: ++ sprintf(tmp, " ctrl"); ++ break; ++ case 1: ++ sprintf(tmp, " isoc"); ++ break; ++ case 2: ++ sprintf(tmp, " bulk"); ++ break; ++ case 3: ++ sprintf(tmp, " intr"); ++ break; ++ } ++ strcat(endpoint_to_str_buff, tmp); ++ if(dir) { ++ sprintf(tmp, " in"); ++ } else { ++ sprintf(tmp, " out"); ++ } ++ strcat(endpoint_to_str_buff, tmp); ++ ++ return endpoint_to_str_buff; ++} ++ ++/* Debug helper functions for Transfer Controller */ ++char* pipe_to_str(unsigned int pipe) { ++ static char pipe_to_str_buff[128]; ++ char tmp[64]; ++ sprintf(pipe_to_str_buff, "dir:%s", str_dir(pipe)); ++ sprintf(tmp, " type:%s", str_type(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ ++ sprintf(tmp, " dev:%d", usb_pipedevice(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ sprintf(tmp, " ep:%d", usb_pipeendpoint(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ return pipe_to_str_buff; + } + +-/* Move an urb to the end of the list. */ +-static inline void urb_list_move_last(struct urb *urb, int epid) +-{ +- urb_entry_t *urb_entry = __urb_list_entry(urb, epid); +- assert(urb_entry); +- +- list_move_tail(&urb_entry->list, &urb_list[epid]); +-} + +-/* Get the next urb in the list. */ +-static inline struct urb *urb_list_next(struct urb *urb, int epid) +-{ +- urb_entry_t *urb_entry = __urb_list_entry(urb, epid); ++#define USB_DEBUG_DESC 1 + +- assert(urb_entry); ++#ifdef USB_DEBUG_DESC ++#define dump_in_desc(x) __dump_in_desc(x) ++#define dump_sb_desc(...) __dump_sb_desc(...) ++#define dump_ep_desc(x) __dump_ep_desc(x) ++#define dump_ept_data(x) __dump_ept_data(x) ++#else ++#define dump_in_desc(...) do {} while (0) ++#define dump_sb_desc(...) do {} while (0) ++#define dump_ep_desc(...) do {} while (0) ++#endif + +- if (urb_entry->list.next != &urb_list[epid]) { +- struct list_head *elem = urb_entry->list.next; +- urb_entry = list_entry(elem, urb_entry_t, list); +- return urb_entry->urb; +- } else { +- return NULL; +- } +-} + ++/* Uncomment this to enable massive function call trace ++ #define USB_DEBUG_TRACE */ + ++#ifdef USB_DEBUG_TRACE ++#define DBFENTER (printk(": Entering: %s\n", __FUNCTION__)) ++#define DBFEXIT (printk(": Exiting: %s\n", __FUNCTION__)) ++#else ++#define DBFENTER do {} while (0) ++#define DBFEXIT do {} while (0) ++#endif + +-/* For debug purposes only. */ +-static inline void urb_list_dump(int epid) +-{ +- struct list_head *entry; +- struct list_head *tmp; +- urb_entry_t *urb_entry; +- int i = 0; +- +- info("Dumping urb list for epid %d", epid); +- +- list_for_each_safe(entry, tmp, &urb_list[epid]) { +- urb_entry = list_entry(entry, urb_entry_t, list); +- info(" entry %d, urb = 0x%lx", i, (unsigned long)urb_entry->urb); +- } +-} ++#define CHECK_ALIGN(x) if (((__u32)(x)) & 0x00000003) \ ++{panic("Alignment check (DWORD) failed at %s:%s:%d\n", __FILE__, __FUNCTION__, __LINE__);} + +-static void init_rx_buffers(void); +-static int etrax_rh_unlink_urb(struct urb *urb); +-static void etrax_rh_send_irq(struct urb *urb); +-static void etrax_rh_init_int_timer(struct urb *urb); +-static void etrax_rh_int_timer_do(unsigned long ptr); +- +-static int etrax_usb_setup_epid(struct urb *urb); +-static int etrax_usb_lookup_epid(struct urb *urb); +-static int etrax_usb_allocate_epid(void); +-static void etrax_usb_free_epid(int epid); +- +-static int etrax_remove_from_sb_list(struct urb *urb); +- +-static void* etrax_usb_buffer_alloc(struct usb_bus* bus, size_t size, +- unsigned mem_flags, dma_addr_t *dma); +-static void etrax_usb_buffer_free(struct usb_bus *bus, size_t size, void *addr, dma_addr_t dma); +- +-static void etrax_usb_add_to_bulk_sb_list(struct urb *urb, int epid); +-static void etrax_usb_add_to_ctrl_sb_list(struct urb *urb, int epid); +-static void etrax_usb_add_to_intr_sb_list(struct urb *urb, int epid); +-static void etrax_usb_add_to_isoc_sb_list(struct urb *urb, int epid); +- +-static int etrax_usb_submit_bulk_urb(struct urb *urb); +-static int etrax_usb_submit_ctrl_urb(struct urb *urb); +-static int etrax_usb_submit_intr_urb(struct urb *urb); +-static int etrax_usb_submit_isoc_urb(struct urb *urb); +- +-static int etrax_usb_submit_urb(struct urb *urb, unsigned mem_flags); +-static int etrax_usb_unlink_urb(struct urb *urb, int status); +-static int etrax_usb_get_frame_number(struct usb_device *usb_dev); +- +-static irqreturn_t etrax_usb_tx_interrupt(int irq, void *vhc); +-static irqreturn_t etrax_usb_rx_interrupt(int irq, void *vhc); +-static irqreturn_t etrax_usb_hc_interrupt_top_half(int irq, void *vhc); +-static void etrax_usb_hc_interrupt_bottom_half(void *data); +- +-static void etrax_usb_isoc_descr_interrupt_bottom_half(void *data); +- +- +-/* The following is a list of interrupt handlers for the host controller interrupts we use. +- They are called from etrax_usb_hc_interrupt_bottom_half. */ +-static void etrax_usb_hc_isoc_eof_interrupt(void); +-static void etrax_usb_hc_bulk_eot_interrupt(int timer_induced); +-static void etrax_usb_hc_epid_attn_interrupt(usb_interrupt_registers_t *reg); +-static void etrax_usb_hc_port_status_interrupt(usb_interrupt_registers_t *reg); +-static void etrax_usb_hc_ctl_status_interrupt(usb_interrupt_registers_t *reg); +- +-static int etrax_rh_submit_urb (struct urb *urb); +- +-/* Forward declaration needed because they are used in the rx interrupt routine. */ +-static void etrax_usb_complete_urb(struct urb *urb, int status); +-static void etrax_usb_complete_bulk_urb(struct urb *urb, int status); +-static void etrax_usb_complete_ctrl_urb(struct urb *urb, int status); +-static void etrax_usb_complete_intr_urb(struct urb *urb, int status); +-static void etrax_usb_complete_isoc_urb(struct urb *urb, int status); ++/* Most helpful debugging aid */ ++#define ASSERT(expr) ((void) ((expr) ? 0 : (err("assert failed at: %s %d",__FUNCTION__, __LINE__)))) + +-static int etrax_usb_hc_init(void); +-static void etrax_usb_hc_cleanup(void); + +-static struct usb_operations etrax_usb_device_operations = +-{ +- .get_frame_number = etrax_usb_get_frame_number, +- .submit_urb = etrax_usb_submit_urb, +- .unlink_urb = etrax_usb_unlink_urb, +- .buffer_alloc = etrax_usb_buffer_alloc, +- .buffer_free = etrax_usb_buffer_free +-}; ++/***************************************************************************/ ++/***************************************************************************/ ++/* Forward declarations */ ++/***************************************************************************/ ++/***************************************************************************/ ++void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg); ++ ++void rh_port_status_change(__u16[]); ++int rh_clear_port_feature(__u8, __u16); ++int rh_set_port_feature(__u8, __u16); ++static void rh_disable_port(unsigned int port); ++ ++static void check_finished_bulk_tx_epids(struct usb_hcd *hcd, ++ int timer); ++ ++static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb, ++ int mem_flags); ++static void tc_free_epid(struct usb_host_endpoint *ep); ++static int tc_allocate_epid(void); ++static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status); ++static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb, ++ int status); ++ ++static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid, ++ int mem_flags); ++static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb); ++ ++static inline struct urb *urb_list_first(int epid); ++static inline void urb_list_add(struct urb *urb, int epid, ++ int mem_flags); ++static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid); ++static inline void urb_list_del(struct urb *urb, int epid); ++static inline void urb_list_move_last(struct urb *urb, int epid); ++static inline struct urb *urb_list_next(struct urb *urb, int epid); ++ ++int create_sb_for_urb(struct urb *urb, int mem_flags); ++int init_intr_urb(struct urb *urb, int mem_flags); ++ ++static inline void etrax_epid_set(__u8 index, __u32 data); ++static inline void etrax_epid_clear_error(__u8 index); ++static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout, ++ __u8 toggle); ++static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout); ++static inline __u32 etrax_epid_get(__u8 index); ++ ++/* We're accessing the same register position in Etrax so ++ when we do full access the internal difference doesn't matter */ ++#define etrax_epid_iso_set(index, data) etrax_epid_set(index, data) ++#define etrax_epid_iso_get(index) etrax_epid_get(index) ++ ++ ++static void tc_dma_process_isoc_urb(struct urb *urb); ++static void tc_dma_process_queue(int epid); ++static void tc_dma_unlink_intr_urb(struct urb *urb); ++static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc); ++static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc); ++ ++static void tc_bulk_start_timer_func(unsigned long dummy); ++static void tc_bulk_eot_timer_func(unsigned long dummy); ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Host Controler Driver block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* HCD operations */ ++static irqreturn_t crisv10_hcd_top_irq(int irq, void*); ++static int crisv10_hcd_reset(struct usb_hcd *); ++static int crisv10_hcd_start(struct usb_hcd *); ++static void crisv10_hcd_stop(struct usb_hcd *); ++#ifdef CONFIG_PM ++static int crisv10_hcd_suspend(struct device *, u32, u32); ++static int crisv10_hcd_resume(struct device *, u32); ++#endif /* CONFIG_PM */ ++static int crisv10_hcd_get_frame(struct usb_hcd *); ++ ++static int tc_urb_enqueue(struct usb_hcd *, struct usb_host_endpoint *ep, struct urb *, gfp_t mem_flags); ++static int tc_urb_dequeue(struct usb_hcd *, struct urb *); ++static void tc_endpoint_disable(struct usb_hcd *, struct usb_host_endpoint *ep); ++ ++static int rh_status_data_request(struct usb_hcd *, char *); ++static int rh_control_request(struct usb_hcd *, u16, u16, u16, char*, u16); ++ ++#ifdef CONFIG_PM ++static int crisv10_hcd_hub_suspend(struct usb_hcd *); ++static int crisv10_hcd_hub_resume(struct usb_hcd *); ++#endif /* CONFIG_PM */ ++#ifdef CONFIG_USB_OTG ++static int crisv10_hcd_start_port_reset(struct usb_hcd *, unsigned); ++#endif /* CONFIG_USB_OTG */ ++ ++/* host controller driver interface */ ++static const struct hc_driver crisv10_hc_driver = ++ { ++ .description = hc_name, ++ .product_desc = product_desc, ++ .hcd_priv_size = sizeof(struct crisv10_hcd), ++ ++ /* Attaching IRQ handler manualy in probe() */ ++ /* .irq = crisv10_hcd_irq, */ ++ ++ .flags = HCD_USB11, ++ ++ /* called to init HCD and root hub */ ++ .reset = crisv10_hcd_reset, ++ .start = crisv10_hcd_start, ++ ++ /* cleanly make HCD stop writing memory and doing I/O */ ++ .stop = crisv10_hcd_stop, ++ ++ /* return current frame number */ ++ .get_frame_number = crisv10_hcd_get_frame, ++ ++ ++ /* Manage i/o requests via the Transfer Controller */ ++ .urb_enqueue = tc_urb_enqueue, ++ .urb_dequeue = tc_urb_dequeue, ++ ++ /* hw synch, freeing endpoint resources that urb_dequeue can't */ ++ .endpoint_disable = tc_endpoint_disable, ++ ++ ++ /* Root Hub support */ ++ .hub_status_data = rh_status_data_request, ++ .hub_control = rh_control_request, ++#ifdef CONFIG_PM ++ .hub_suspend = rh_suspend_request, ++ .hub_resume = rh_resume_request, ++#endif /* CONFIG_PM */ ++#ifdef CONFIG_USB_OTG ++ .start_port_reset = crisv10_hcd_start_port_reset, ++#endif /* CONFIG_USB_OTG */ ++ }; + +-/* Note that these functions are always available in their "__" variants, for use in +- error situations. The "__" missing variants are controlled by the USB_DEBUG_DESC/ +- USB_DEBUG_URB macros. */ +-static void __dump_urb(struct urb* purb) +-{ +- printk("\nurb :0x%08lx\n", (unsigned long)purb); +- printk("dev :0x%08lx\n", (unsigned long)purb->dev); +- printk("pipe :0x%08x\n", purb->pipe); +- printk("status :%d\n", purb->status); +- printk("transfer_flags :0x%08x\n", purb->transfer_flags); +- printk("transfer_buffer :0x%08lx\n", (unsigned long)purb->transfer_buffer); +- printk("transfer_buffer_length:%d\n", purb->transfer_buffer_length); +- printk("actual_length :%d\n", purb->actual_length); +- printk("setup_packet :0x%08lx\n", (unsigned long)purb->setup_packet); +- printk("start_frame :%d\n", purb->start_frame); +- printk("number_of_packets :%d\n", purb->number_of_packets); +- printk("interval :%d\n", purb->interval); +- printk("error_count :%d\n", purb->error_count); +- printk("context :0x%08lx\n", (unsigned long)purb->context); +- printk("complete :0x%08lx\n\n", (unsigned long)purb->complete); +-} + +-static void __dump_in_desc(volatile USB_IN_Desc_t *in) +-{ +- printk("\nUSB_IN_Desc at 0x%08lx\n", (unsigned long)in); +- printk(" sw_len : 0x%04x (%d)\n", in->sw_len, in->sw_len); +- printk(" command : 0x%04x\n", in->command); +- printk(" next : 0x%08lx\n", in->next); +- printk(" buf : 0x%08lx\n", in->buf); +- printk(" hw_len : 0x%04x (%d)\n", in->hw_len, in->hw_len); +- printk(" status : 0x%04x\n\n", in->status); +-} ++/* ++ * conversion between pointers to a hcd and the corresponding ++ * crisv10_hcd ++ */ + +-static void __dump_sb_desc(volatile USB_SB_Desc_t *sb) ++static inline struct crisv10_hcd *hcd_to_crisv10_hcd(struct usb_hcd *hcd) + { +- char tt = (sb->command & 0x30) >> 4; +- char *tt_string; +- +- switch (tt) { +- case 0: +- tt_string = "zout"; +- break; +- case 1: +- tt_string = "in"; +- break; +- case 2: +- tt_string = "out"; +- break; +- case 3: +- tt_string = "setup"; +- break; +- default: +- tt_string = "unknown (weird)"; +- } +- +- printk("\n USB_SB_Desc at 0x%08lx\n", (unsigned long)sb); +- printk(" command : 0x%04x\n", sb->command); +- printk(" rem : %d\n", (sb->command & 0x3f00) >> 8); +- printk(" full : %d\n", (sb->command & 0x40) >> 6); +- printk(" tt : %d (%s)\n", tt, tt_string); +- printk(" intr : %d\n", (sb->command & 0x8) >> 3); +- printk(" eot : %d\n", (sb->command & 0x2) >> 1); +- printk(" eol : %d\n", sb->command & 0x1); +- printk(" sw_len : 0x%04x (%d)\n", sb->sw_len, sb->sw_len); +- printk(" next : 0x%08lx\n", sb->next); +- printk(" buf : 0x%08lx\n\n", sb->buf); ++ return (struct crisv10_hcd *) hcd->hcd_priv; + } + +- +-static void __dump_ep_desc(volatile USB_EP_Desc_t *ep) ++static inline struct usb_hcd *crisv10_hcd_to_hcd(struct crisv10_hcd *hcd) + { +- printk("\nUSB_EP_Desc at 0x%08lx\n", (unsigned long)ep); +- printk(" command : 0x%04x\n", ep->command); +- printk(" ep_id : %d\n", (ep->command & 0x1f00) >> 8); +- printk(" enable : %d\n", (ep->command & 0x10) >> 4); +- printk(" intr : %d\n", (ep->command & 0x8) >> 3); +- printk(" eof : %d\n", (ep->command & 0x2) >> 1); +- printk(" eol : %d\n", ep->command & 0x1); +- printk(" hw_len : 0x%04x (%d)\n", ep->hw_len, ep->hw_len); +- printk(" next : 0x%08lx\n", ep->next); +- printk(" sub : 0x%08lx\n\n", ep->sub); ++ return container_of((void *) hcd, struct usb_hcd, hcd_priv); + } + +-static inline void __dump_ep_list(int pipe_type) ++/* check if specified port is in use */ ++static inline int port_in_use(unsigned int port) + { +- volatile USB_EP_Desc_t *ep; +- volatile USB_EP_Desc_t *first_ep; +- volatile USB_SB_Desc_t *sb; +- +- switch (pipe_type) +- { +- case PIPE_BULK: +- first_ep = &TxBulkEPList[0]; +- break; +- case PIPE_CONTROL: +- first_ep = &TxCtrlEPList[0]; +- break; +- case PIPE_INTERRUPT: +- first_ep = &TxIntrEPList[0]; +- break; +- case PIPE_ISOCHRONOUS: +- first_ep = &TxIsocEPList[0]; +- break; +- default: +- warn("Cannot dump unknown traffic type"); +- return; +- } +- ep = first_ep; +- +- printk("\n\nDumping EP list...\n\n"); +- +- do { +- __dump_ep_desc(ep); +- /* Cannot phys_to_virt on 0 as it turns into 80000000, which is != 0. */ +- sb = ep->sub ? phys_to_virt(ep->sub) : 0; +- while (sb) { +- __dump_sb_desc(sb); +- sb = sb->next ? phys_to_virt(sb->next) : 0; +- } +- ep = (volatile USB_EP_Desc_t *)(phys_to_virt(ep->next)); +- +- } while (ep != first_ep); ++ return ports & (1 << port); + } + +-static inline void __dump_ept_data(int epid) ++/* number of ports in use */ ++static inline unsigned int num_ports(void) + { +- unsigned long flags; +- __u32 r_usb_ept_data; +- +- if (epid < 0 || epid > 31) { +- printk("Cannot dump ept data for invalid epid %d\n", epid); +- return; +- } +- +- save_flags(flags); +- cli(); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- r_usb_ept_data = *R_USB_EPT_DATA; +- restore_flags(flags); +- +- printk("\nR_USB_EPT_DATA = 0x%x for epid %d :\n", r_usb_ept_data, epid); +- if (r_usb_ept_data == 0) { +- /* No need for more detailed printing. */ +- return; +- } +- printk(" valid : %d\n", (r_usb_ept_data & 0x80000000) >> 31); +- printk(" hold : %d\n", (r_usb_ept_data & 0x40000000) >> 30); +- printk(" error_count_in : %d\n", (r_usb_ept_data & 0x30000000) >> 28); +- printk(" t_in : %d\n", (r_usb_ept_data & 0x08000000) >> 27); +- printk(" low_speed : %d\n", (r_usb_ept_data & 0x04000000) >> 26); +- printk(" port : %d\n", (r_usb_ept_data & 0x03000000) >> 24); +- printk(" error_code : %d\n", (r_usb_ept_data & 0x00c00000) >> 22); +- printk(" t_out : %d\n", (r_usb_ept_data & 0x00200000) >> 21); +- printk(" error_count_out : %d\n", (r_usb_ept_data & 0x00180000) >> 19); +- printk(" max_len : %d\n", (r_usb_ept_data & 0x0003f800) >> 11); +- printk(" ep : %d\n", (r_usb_ept_data & 0x00000780) >> 7); +- printk(" dev : %d\n", (r_usb_ept_data & 0x0000003f)); ++ unsigned int i, num = 0; ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) ++ if (port_in_use(i)) ++ num++; ++ return num; + } + +-static inline void __dump_ept_data_list(void) ++/* map hub port number to the port number used internally by the HC */ ++static inline unsigned int map_port(unsigned int port) + { +- int i; +- +- printk("Dumping the whole R_USB_EPT_DATA list\n"); +- +- for (i = 0; i < 32; i++) { +- __dump_ept_data(i); +- } ++ unsigned int i, num = 0; ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) ++ if (port_in_use(i)) ++ if (++num == port) ++ return i; ++ return -1; + } +-#ifdef USB_DEBUG_DESC +-#define dump_in_desc(...) __dump_in_desc(...) +-#define dump_sb_desc(...) __dump_sb_desc(...) +-#define dump_ep_desc(...) __dump_ep_desc(...) +-#else +-#define dump_in_desc(...) do {} while (0) +-#define dump_sb_desc(...) do {} while (0) +-#define dump_ep_desc(...) do {} while (0) +-#endif + +-#ifdef USB_DEBUG_URB +-#define dump_urb(x) __dump_urb(x) +-#else +-#define dump_urb(x) do {} while (0) ++/* size of descriptors in slab cache */ ++#ifndef MAX ++#define MAX(x, y) ((x) > (y) ? (x) : (y)) + #endif + +-static void init_rx_buffers(void) +-{ +- int i; + +- DBFENTER; ++/******************************************************************/ ++/* Hardware Interrupt functions */ ++/******************************************************************/ ++ ++/* Fast interrupt handler for HC */ ++static irqreturn_t crisv10_hcd_top_irq(int irq, void *vcd) ++{ ++ struct usb_hcd *hcd = vcd; ++ struct crisv10_irq_reg reg; ++ __u32 irq_mask; ++ unsigned long flags; ++ ++ DBFENTER; ++ ++ ASSERT(hcd != NULL); ++ reg.hcd = hcd; ++ ++ /* Turn of other interrupts while handling these sensitive cases */ ++ local_irq_save(flags); ++ ++ /* Read out which interrupts that are flaged */ ++ irq_mask = *R_USB_IRQ_MASK_READ; ++ reg.r_usb_irq_mask_read = irq_mask; ++ ++ /* Reading R_USB_STATUS clears the ctl_status interrupt. Note that ++ R_USB_STATUS must be read before R_USB_EPID_ATTN since reading the latter ++ clears the ourun and perror fields of R_USB_STATUS. */ ++ reg.r_usb_status = *R_USB_STATUS; ++ ++ /* Reading R_USB_EPID_ATTN clears the iso_eof, bulk_eot and epid_attn ++ interrupts. */ ++ reg.r_usb_epid_attn = *R_USB_EPID_ATTN; ++ ++ /* Reading R_USB_RH_PORT_STATUS_1 and R_USB_RH_PORT_STATUS_2 clears the ++ port_status interrupt. */ ++ reg.r_usb_rh_port_status_1 = *R_USB_RH_PORT_STATUS_1; ++ reg.r_usb_rh_port_status_2 = *R_USB_RH_PORT_STATUS_2; ++ ++ /* Reading R_USB_FM_NUMBER clears the sof interrupt. */ ++ /* Note: the lower 11 bits contain the actual frame number, sent with each ++ sof. */ ++ reg.r_usb_fm_number = *R_USB_FM_NUMBER; ++ ++ /* Interrupts are handled in order of priority. */ ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, port_status)) { ++ crisv10_hcd_port_status_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, epid_attn)) { ++ crisv10_hcd_epid_attn_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, ctl_status)) { ++ crisv10_hcd_ctl_status_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, iso_eof)) { ++ crisv10_hcd_isoc_eof_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, bulk_eot)) { ++ /* Update/restart the bulk start timer since obviously the channel is ++ running. */ ++ mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); ++ /* Update/restart the bulk eot timer since we just received an bulk eot ++ interrupt. */ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ ++ /* Check for finished bulk transfers on epids */ ++ check_finished_bulk_tx_epids(hcd, 0); ++ } ++ local_irq_restore(flags); ++ ++ DBFEXIT; ++ return IRQ_HANDLED; ++} ++ ++ ++void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg) { ++ struct usb_hcd *hcd = reg->hcd; ++ struct crisv10_urb_priv *urb_priv; ++ int epid; ++ DBFENTER; ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (test_bit(epid, (void *)®->r_usb_epid_attn)) { ++ struct urb *urb; ++ __u32 ept_data; ++ int error_code; ++ ++ if (epid == DUMMY_EPID || epid == INVALID_EPID) { ++ /* We definitely don't care about these ones. Besides, they are ++ always disabled, so any possible disabling caused by the ++ epid attention interrupt is irrelevant. */ ++ warn("Got epid_attn for INVALID_EPID or DUMMY_EPID (%d).", epid); ++ continue; ++ } ++ ++ if(!epid_inuse(epid)) { ++ irq_err("Epid attention on epid:%d that isn't in use\n", epid); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ debug_epid(epid); ++ continue; ++ } ++ ++ /* Note that although there are separate R_USB_EPT_DATA and ++ R_USB_EPT_DATA_ISO registers, they are located at the same address and ++ are of the same size. In other words, this read should be ok for isoc ++ also. */ ++ ept_data = etrax_epid_get(epid); ++ error_code = IO_EXTRACT(R_USB_EPT_DATA, error_code, ept_data); ++ ++ /* Get the active URB for this epid. We blatantly assume ++ that only this URB could have caused the epid attention. */ ++ urb = activeUrbList[epid]; ++ if (urb == NULL) { ++ irq_err("Attention on epid:%d error:%d with no active URB.\n", ++ epid, error_code); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ debug_epid(epid); ++ continue; ++ } ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Using IO_STATE_VALUE on R_USB_EPT_DATA should be ok for isoc also. */ ++ if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ ++ /* Isoc traffic doesn't have error_count_in/error_count_out. */ ++ if ((usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) && ++ (IO_EXTRACT(R_USB_EPT_DATA, error_count_in, ept_data) == 3 || ++ IO_EXTRACT(R_USB_EPT_DATA, error_count_out, ept_data) == 3)) { ++ /* Check if URB allready is marked for late-finish, we can get ++ several 3rd error for Intr traffic when a device is unplugged */ ++ if(urb_priv->later_data == NULL) { ++ /* 3rd error. */ ++ irq_warn("3rd error for epid:%d (%s %s) URB:0x%x[%d]\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe), ++ (unsigned int)urb, urb_priv->urb_num); ++ ++ tc_finish_urb_later(hcd, urb, -EPROTO); ++ } ++ ++ } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { ++ irq_warn("Perror for epid:%d\n", epid); ++ printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); ++ ++ if (!(ept_data & IO_MASK(R_USB_EPT_DATA, valid))) { ++ /* invalid ep_id */ ++ panic("Perror because of invalid epid." ++ " Deconfigured too early?"); ++ } else { ++ /* past eof1, near eof, zout transfer, setup transfer */ ++ /* Dump the urb and the relevant EP descriptor. */ ++ panic("Something wrong with DMA descriptor contents." ++ " Too much traffic inserted?"); ++ } ++ } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { ++ /* buffer ourun */ ++ printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); + +- for (i = 0; i < (NBR_OF_RX_DESC - 1); i++) { +- RxDescList[i].sw_len = RX_DESC_BUF_SIZE; +- RxDescList[i].command = 0; +- RxDescList[i].next = virt_to_phys(&RxDescList[i + 1]); +- RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); +- RxDescList[i].hw_len = 0; +- RxDescList[i].status = 0; +- +- /* DMA IN cache bug. (struct etrax_dma_descr has the same layout as USB_IN_Desc +- for the relevant fields.) */ +- prepare_rx_descriptor((struct etrax_dma_descr*)&RxDescList[i]); ++ panic("Buffer overrun/underrun for epid:%d. DMA too busy?", epid); ++ } else { ++ irq_warn("Attention on epid:%d (%s %s) with no error code\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); ++ } + ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ stall)) { ++ /* Not really a protocol error, just says that the endpoint gave ++ a stall response. Note that error_code cannot be stall for isoc. */ ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ panic("Isoc traffic cannot stall"); + } + +- RxDescList[i].sw_len = RX_DESC_BUF_SIZE; +- RxDescList[i].command = IO_STATE(USB_IN_command, eol, yes); +- RxDescList[i].next = virt_to_phys(&RxDescList[0]); +- RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); +- RxDescList[i].hw_len = 0; +- RxDescList[i].status = 0; ++ tc_dbg("Stall for epid:%d (%s %s) URB:0x%x\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe), (unsigned int)urb); ++ tc_finish_urb(hcd, urb, -EPIPE); ++ ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ bus_error)) { ++ /* Two devices responded to a transaction request. Must be resolved ++ by software. FIXME: Reset ports? */ ++ panic("Bus error for epid %d." ++ " Two devices responded to transaction request\n", ++ epid); ++ ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ buffer_error)) { ++ /* DMA overrun or underrun. */ ++ irq_warn("Buffer overrun/underrun for epid:%d (%s %s)\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ ++ /* It seems that error_code = buffer_error in ++ R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS ++ are the same error. */ ++ tc_finish_urb(hcd, urb, -EPROTO); ++ } else { ++ irq_warn("Unknown attention on epid:%d (%s %s)\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ dump_ept_data(epid); ++ } ++ } ++ } ++ DBFEXIT; ++} ++ ++void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg) ++{ ++ __u16 port_reg[USB_ROOT_HUB_PORTS]; ++ DBFENTER; ++ port_reg[0] = reg->r_usb_rh_port_status_1; ++ port_reg[1] = reg->r_usb_rh_port_status_2; ++ rh_port_status_change(port_reg); ++ DBFEXIT; ++} ++ ++void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg) ++{ ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv *urb_priv; ++ ++ DBFENTER; ++ ++ for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { ++ ++ /* Only check epids that are in use, is valid and has SB list */ ++ if (!epid_inuse(epid) || epid == INVALID_EPID || ++ TxIsocEPList[epid].sub == 0 || epid == DUMMY_EPID) { ++ /* Nothing here to see. */ ++ continue; ++ } ++ ASSERT(epid_isoc(epid)); ++ ++ /* Get the active URB for this epid (if any). */ ++ urb = activeUrbList[epid]; ++ if (urb == 0) { ++ isoc_warn("Ignoring NULL urb for epid:%d\n", epid); ++ continue; ++ } ++ if(!epid_out_traffic(epid)) { ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ if (urb_priv->urb_state == NOT_STARTED) { ++ /* If ASAP is not set and urb->start_frame is the current frame, ++ start the transfer. */ ++ if (!(urb->transfer_flags & URB_ISO_ASAP) && ++ (urb->start_frame == (*R_USB_FM_NUMBER & 0x7ff))) { ++ /* EP should not be enabled if we're waiting for start_frame */ ++ ASSERT((TxIsocEPList[epid].command & ++ IO_STATE(USB_EP_command, enable, yes)) == 0); ++ ++ isoc_warn("Enabling isoc IN EP descr for epid %d\n", epid); ++ TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ /* This urb is now active. */ ++ urb_priv->urb_state = STARTED; ++ continue; ++ } ++ } ++ } ++ } ++ ++ DBFEXIT; ++} ++ ++void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg) ++{ ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(reg->hcd); ++ ++ DBFENTER; ++ ASSERT(crisv10_hcd); ++ ++ irq_dbg("ctr_status_irq, controller status: %s\n", ++ hcd_status_to_str(reg->r_usb_status)); ++ ++ /* FIXME: What should we do if we get ourun or perror? Dump the EP and SB ++ list for the corresponding epid? */ ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { ++ panic("USB controller got ourun."); ++ } ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { ++ ++ /* Before, etrax_usb_do_intr_recover was called on this epid if it was ++ an interrupt pipe. I don't see how re-enabling all EP descriptors ++ will help if there was a programming error. */ ++ panic("USB controller got perror."); ++ } ++ ++ /* Keep track of USB Controller, if it's running or not */ ++ if(reg->r_usb_status & IO_STATE(R_USB_STATUS, running, yes)) { ++ crisv10_hcd->running = 1; ++ } else { ++ crisv10_hcd->running = 0; ++ } ++ ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, device_mode)) { ++ /* We should never operate in device mode. */ ++ panic("USB controller in device mode."); ++ } ++ ++ /* Set the flag to avoid getting "Unlink after no-IRQ? Controller is probably ++ using the wrong IRQ" from hcd_unlink_urb() in drivers/usb/core/hcd.c */ ++ set_bit(HCD_FLAG_SAW_IRQ, ®->hcd->flags); ++ ++ DBFEXIT; ++} ++ ++ ++/******************************************************************/ ++/* Host Controller interface functions */ ++/******************************************************************/ ++ ++static inline void crisv10_ready_wait(void) { ++ volatile int timeout = 10000; ++ /* Check the busy bit of USB controller in Etrax */ ++ while((*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for USB controller to be idle\n"); ++ } ++} ++ ++/* reset host controller */ ++static int crisv10_hcd_reset(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "reset\n"); ++ ++ ++ /* Reset the USB interface. */ ++ /* ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, reset); ++ nop(); ++ */ ++ DBFEXIT; ++ return 0; ++} ++ ++/* start host controller */ ++static int crisv10_hcd_start(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "start\n"); ++ ++ crisv10_ready_wait(); ++ ++ /* Start processing of USB traffic. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ ++ nop(); ++ ++ hcd->state = HC_STATE_RUNNING; ++ ++ DBFEXIT; ++ return 0; ++} ++ ++/* stop host controller */ ++static void crisv10_hcd_stop(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "stop\n"); ++ crisv10_hcd_reset(hcd); ++ DBFEXIT; ++} ++ ++/* return the current frame number */ ++static int crisv10_hcd_get_frame(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ DBFEXIT; ++ return (*R_USB_FM_NUMBER & 0x7ff); ++} ++ ++#ifdef CONFIG_USB_OTG ++ ++static int crisv10_hcd_start_port_reset(struct usb_hcd *hcd, unsigned port) ++{ ++ return 0; /* no-op for now */ ++} ++ ++#endif /* CONFIG_USB_OTG */ ++ ++ ++/******************************************************************/ ++/* Root Hub functions */ ++/******************************************************************/ ++ ++/* root hub status */ ++static const struct usb_hub_status rh_hub_status = ++ { ++ .wHubStatus = 0, ++ .wHubChange = 0, ++ }; ++ ++/* root hub descriptor */ ++static const u8 rh_hub_descr[] = ++ { ++ 0x09, /* bDescLength */ ++ 0x29, /* bDescriptorType */ ++ USB_ROOT_HUB_PORTS, /* bNbrPorts */ ++ 0x00, /* wHubCharacteristics */ ++ 0x00, ++ 0x01, /* bPwrOn2pwrGood */ ++ 0x00, /* bHubContrCurrent */ ++ 0x00, /* DeviceRemovable */ ++ 0xff /* PortPwrCtrlMask */ ++ }; ++ ++/* Actual holder of root hub status*/ ++struct crisv10_rh rh; ++ ++/* Initialize root hub data structures (called from dvdrv_hcd_probe()) */ ++int rh_init(void) { ++ int i; ++ /* Reset port status flags */ ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) { ++ rh.wPortChange[i] = 0; ++ rh.wPortStatusPrev[i] = 0; ++ } ++ return 0; ++} ++ ++#define RH_FEAT_MASK ((1<<USB_PORT_FEAT_CONNECTION)|\ ++ (1<<USB_PORT_FEAT_ENABLE)|\ ++ (1<<USB_PORT_FEAT_SUSPEND)|\ ++ (1<<USB_PORT_FEAT_RESET)) ++ ++/* Handle port status change interrupt (called from bottom part interrupt) */ ++void rh_port_status_change(__u16 port_reg[]) { ++ int i; ++ __u16 wChange; ++ ++ for(i = 0; i < USB_ROOT_HUB_PORTS; i++) { ++ /* Xor out changes since last read, masked for important flags */ ++ wChange = (port_reg[i] & RH_FEAT_MASK) ^ rh.wPortStatusPrev[i]; ++ /* Or changes together with (if any) saved changes */ ++ rh.wPortChange[i] |= wChange; ++ /* Save new status */ ++ rh.wPortStatusPrev[i] = port_reg[i]; ++ ++ if(wChange) { ++ rh_dbg("Interrupt port_status change port%d: %s Current-status:%s\n", i+1, ++ port_status_to_str(wChange), ++ port_status_to_str(port_reg[i])); ++ } ++ } ++} ++ ++/* Construct port status change bitmap for the root hub */ ++static int rh_status_data_request(struct usb_hcd *hcd, char *buf) ++{ ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ unsigned int i; ++ ++ DBFENTER; ++ /* ++ * corresponds to hub status change EP (USB 2.0 spec section 11.13.4) ++ * return bitmap indicating ports with status change ++ */ ++ *buf = 0; ++ spin_lock(&crisv10_hcd->lock); ++ for (i = 1; i <= crisv10_hcd->num_ports; i++) { ++ if (rh.wPortChange[map_port(i)]) { ++ *buf |= (1 << i); ++ rh_dbg("rh_status_data_request, change on port %d: %s Current Status: %s\n", i, ++ port_status_to_str(rh.wPortChange[map_port(i)]), ++ port_status_to_str(rh.wPortStatusPrev[map_port(i)])); ++ } ++ } ++ spin_unlock(&crisv10_hcd->lock); ++ DBFEXIT; ++ return *buf == 0 ? 0 : 1; ++} ++ ++/* Handle a control request for the root hub (called from hcd_driver) */ ++static int rh_control_request(struct usb_hcd *hcd, ++ u16 typeReq, ++ u16 wValue, ++ u16 wIndex, ++ char *buf, ++ u16 wLength) { ++ ++ struct crisv10_hcd *crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ int retval = 0; ++ int len; ++ DBFENTER; ++ ++ switch (typeReq) { ++ case GetHubDescriptor: ++ rh_dbg("GetHubDescriptor\n"); ++ len = min_t(unsigned int, sizeof rh_hub_descr, wLength); ++ memcpy(buf, rh_hub_descr, len); ++ buf[2] = crisv10_hcd->num_ports; ++ break; ++ case GetHubStatus: ++ rh_dbg("GetHubStatus\n"); ++ len = min_t(unsigned int, sizeof rh_hub_status, wLength); ++ memcpy(buf, &rh_hub_status, len); ++ break; ++ case GetPortStatus: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ rh_dbg("GetportStatus, port:%d change:%s status:%s\n", wIndex, ++ port_status_to_str(rh.wPortChange[map_port(wIndex)]), ++ port_status_to_str(rh.wPortStatusPrev[map_port(wIndex)])); ++ *(u16 *) buf = cpu_to_le16(rh.wPortStatusPrev[map_port(wIndex)]); ++ *(u16 *) (buf + 2) = cpu_to_le16(rh.wPortChange[map_port(wIndex)]); ++ break; ++ case SetHubFeature: ++ rh_dbg("SetHubFeature\n"); ++ case ClearHubFeature: ++ rh_dbg("ClearHubFeature\n"); ++ switch (wValue) { ++ case C_HUB_OVER_CURRENT: ++ case C_HUB_LOCAL_POWER: ++ rh_warn("Not implemented hub request:%d \n", typeReq); ++ /* not implemented */ ++ break; ++ default: ++ goto error; ++ } ++ break; ++ case SetPortFeature: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ if(rh_set_port_feature(map_port(wIndex), wValue)) ++ goto error; ++ break; ++ case ClearPortFeature: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ if(rh_clear_port_feature(map_port(wIndex), wValue)) ++ goto error; ++ break; ++ default: ++ rh_warn("Unknown hub request: %d\n", typeReq); ++ error: ++ retval = -EPIPE; ++ } ++ DBFEXIT; ++ return retval; ++} ++ ++int rh_set_port_feature(__u8 bPort, __u16 wFeature) { ++ __u8 bUsbCommand = 0; ++ switch(wFeature) { ++ case USB_PORT_FEAT_RESET: ++ rh_dbg("SetPortFeature: reset\n"); ++ bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, reset); ++ goto set; ++ break; ++ case USB_PORT_FEAT_SUSPEND: ++ rh_dbg("SetPortFeature: suspend\n"); ++ bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, suspend); ++ goto set; ++ break; ++ case USB_PORT_FEAT_POWER: ++ rh_dbg("SetPortFeature: power\n"); ++ break; ++ case USB_PORT_FEAT_C_CONNECTION: ++ rh_dbg("SetPortFeature: c_connection\n"); ++ break; ++ case USB_PORT_FEAT_C_RESET: ++ rh_dbg("SetPortFeature: c_reset\n"); ++ break; ++ case USB_PORT_FEAT_C_OVER_CURRENT: ++ rh_dbg("SetPortFeature: c_over_current\n"); ++ break; ++ ++ set: ++ /* Select which port via the port_sel field */ ++ bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1); ++ ++ /* Make sure the controller isn't busy. */ ++ crisv10_ready_wait(); ++ /* Send out the actual command to the USB controller */ ++ *R_USB_COMMAND = bUsbCommand; ++ ++ /* If port reset then also bring USB controller into running state */ ++ if(wFeature == USB_PORT_FEAT_RESET) { ++ /* Wait a while for controller to first become started after port reset */ ++ udelay(12000); /* 12ms blocking wait */ ++ ++ /* Make sure the controller isn't busy. */ ++ crisv10_ready_wait(); ++ ++ /* If all enabled ports were disabled the host controller goes down into ++ started mode, so we need to bring it back into the running state. ++ (This is safe even if it's already in the running state.) */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ } ++ ++ break; ++ default: ++ rh_dbg("SetPortFeature: unknown feature\n"); ++ return -1; ++ } ++ return 0; ++} ++ ++int rh_clear_port_feature(__u8 bPort, __u16 wFeature) { ++ switch(wFeature) { ++ case USB_PORT_FEAT_ENABLE: ++ rh_dbg("ClearPortFeature: enable\n"); ++ rh_disable_port(bPort); ++ break; ++ case USB_PORT_FEAT_SUSPEND: ++ rh_dbg("ClearPortFeature: suspend\n"); ++ break; ++ case USB_PORT_FEAT_POWER: ++ rh_dbg("ClearPortFeature: power\n"); ++ break; ++ ++ case USB_PORT_FEAT_C_ENABLE: ++ rh_dbg("ClearPortFeature: c_enable\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_SUSPEND: ++ rh_dbg("ClearPortFeature: c_suspend\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_CONNECTION: ++ rh_dbg("ClearPortFeature: c_connection\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_OVER_CURRENT: ++ rh_dbg("ClearPortFeature: c_over_current\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_RESET: ++ rh_dbg("ClearPortFeature: c_reset\n"); ++ goto clear; ++ clear: ++ rh.wPortChange[bPort] &= ~(1 << (wFeature - 16)); ++ break; ++ default: ++ rh_dbg("ClearPortFeature: unknown feature\n"); ++ return -1; ++ } ++ return 0; ++} ++ ++ ++#ifdef CONFIG_PM ++/* Handle a suspend request for the root hub (called from hcd_driver) */ ++static int rh_suspend_request(struct usb_hcd *hcd) ++{ ++ return 0; /* no-op for now */ ++} ++ ++/* Handle a resume request for the root hub (called from hcd_driver) */ ++static int rh_resume_request(struct usb_hcd *hcd) ++{ ++ return 0; /* no-op for now */ ++} ++#endif /* CONFIG_PM */ ++ ++ ++ ++/* Wrapper function for workaround port disable registers in USB controller */ ++static void rh_disable_port(unsigned int port) { ++ volatile int timeout = 10000; ++ volatile char* usb_portx_disable; ++ switch(port) { ++ case 0: ++ usb_portx_disable = R_USB_PORT1_DISABLE; ++ break; ++ case 1: ++ usb_portx_disable = R_USB_PORT2_DISABLE; ++ break; ++ default: ++ /* Invalid port index */ ++ return; ++ } ++ /* Set disable flag in special register */ ++ *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, yes); ++ /* Wait until not enabled anymore */ ++ while((rh.wPortStatusPrev[port] & ++ IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for port %d to become disabled\n", port); ++ } ++ /* clear disable flag in special register */ ++ *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, no); ++ rh_info("Physical port %d disabled\n", port+1); ++} ++ ++ ++/******************************************************************/ ++/* Transfer Controller (TC) functions */ ++/******************************************************************/ ++ ++/* FIXME: Should RX_BUF_SIZE be a config option, or maybe we should adjust it ++ dynamically? ++ To adjust it dynamically we would have to get an interrupt when we reach ++ the end of the rx descriptor list, or when we get close to the end, and ++ then allocate more descriptors. */ ++#define NBR_OF_RX_DESC 512 ++#define RX_DESC_BUF_SIZE 1024 ++#define RX_BUF_SIZE (NBR_OF_RX_DESC * RX_DESC_BUF_SIZE) + +- myNextRxDesc = &RxDescList[0]; +- myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; +- myPrevRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; + +- *R_DMA_CH9_FIRST = virt_to_phys(myNextRxDesc); +- *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, start); ++/* Local variables for Transfer Controller */ ++/* --------------------------------------- */ + +- DBFEXIT; +-} ++/* This is a circular (double-linked) list of the active urbs for each epid. ++ The head is never removed, and new urbs are linked onto the list as ++ urb_entry_t elements. Don't reference urb_list directly; use the wrapper ++ functions instead (which includes spin_locks) */ ++static struct list_head urb_list[NBR_OF_EPIDS]; + +-static void init_tx_bulk_ep(void) +-{ +- int i; ++/* Read about the need and usage of this lock in submit_ctrl_urb. */ ++/* Lock for URB lists for each EPID */ ++static spinlock_t urb_list_lock; + +- DBFENTER; ++/* Lock for EPID array register (R_USB_EPT_x) in Etrax */ ++static spinlock_t etrax_epid_lock; + +- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { +- CHECK_ALIGN(&TxBulkEPList[i]); +- TxBulkEPList[i].hw_len = 0; +- TxBulkEPList[i].command = IO_FIELD(USB_EP_command, epid, i); +- TxBulkEPList[i].sub = 0; +- TxBulkEPList[i].next = virt_to_phys(&TxBulkEPList[i + 1]); +- +- /* Initiate two EPs, disabled and with the eol flag set. No need for any +- preserved epid. */ +- +- /* The first one has the intr flag set so we get an interrupt when the DMA +- channel is about to become disabled. */ +- CHECK_ALIGN(&TxBulkDummyEPList[i][0]); +- TxBulkDummyEPList[i][0].hw_len = 0; +- TxBulkDummyEPList[i][0].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | +- IO_STATE(USB_EP_command, eol, yes) | +- IO_STATE(USB_EP_command, intr, yes)); +- TxBulkDummyEPList[i][0].sub = 0; +- TxBulkDummyEPList[i][0].next = virt_to_phys(&TxBulkDummyEPList[i][1]); +- +- /* The second one. */ +- CHECK_ALIGN(&TxBulkDummyEPList[i][1]); +- TxBulkDummyEPList[i][1].hw_len = 0; +- TxBulkDummyEPList[i][1].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | +- IO_STATE(USB_EP_command, eol, yes)); +- TxBulkDummyEPList[i][1].sub = 0; +- /* The last dummy's next pointer is the same as the current EP's next pointer. */ +- TxBulkDummyEPList[i][1].next = virt_to_phys(&TxBulkEPList[i + 1]); +- } ++/* Lock for dma8 sub0 handling */ ++static spinlock_t etrax_dma8_sub0_lock; + +- /* Configure the last one. */ +- CHECK_ALIGN(&TxBulkEPList[i]); +- TxBulkEPList[i].hw_len = 0; +- TxBulkEPList[i].command = (IO_STATE(USB_EP_command, eol, yes) | +- IO_FIELD(USB_EP_command, epid, i)); +- TxBulkEPList[i].sub = 0; +- TxBulkEPList[i].next = virt_to_phys(&TxBulkEPList[0]); +- +- /* No need configuring dummy EPs for the last one as it will never be used for +- bulk traffic (i == INVALD_EPID at this point). */ +- +- /* Set up to start on the last EP so we will enable it when inserting traffic +- for the first time (imitating the situation where the DMA has stopped +- because there was no more traffic). */ +- *R_DMA_CH8_SUB0_EP = virt_to_phys(&TxBulkEPList[i]); +- /* No point in starting the bulk channel yet. +- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */ +- DBFEXIT; +-} ++/* DMA IN cache bug. Align the DMA IN buffers to 32 bytes, i.e. a cache line. ++ Since RX_DESC_BUF_SIZE is 1024 is a multiple of 32, all rx buffers will be ++ cache aligned. */ ++static volatile unsigned char RxBuf[RX_BUF_SIZE] __attribute__ ((aligned (32))); ++static volatile struct USB_IN_Desc RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned (4))); + +-static void init_tx_ctrl_ep(void) +-{ +- int i; ++/* Pointers into RxDescList. */ ++static volatile struct USB_IN_Desc *myNextRxDesc; ++static volatile struct USB_IN_Desc *myLastRxDesc; + +- DBFENTER; ++/* A zout transfer makes a memory access at the address of its buf pointer, ++ which means that setting this buf pointer to 0 will cause an access to the ++ flash. In addition to this, setting sw_len to 0 results in a 16/32 bytes ++ (depending on DMA burst size) transfer. ++ Instead, we set it to 1, and point it to this buffer. */ ++static int zout_buffer[4] __attribute__ ((aligned (4))); + +- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { +- CHECK_ALIGN(&TxCtrlEPList[i]); +- TxCtrlEPList[i].hw_len = 0; +- TxCtrlEPList[i].command = IO_FIELD(USB_EP_command, epid, i); +- TxCtrlEPList[i].sub = 0; +- TxCtrlEPList[i].next = virt_to_phys(&TxCtrlEPList[i + 1]); +- } ++/* Cache for allocating new EP and SB descriptors. */ ++static kmem_cache_t *usb_desc_cache; + +- CHECK_ALIGN(&TxCtrlEPList[i]); +- TxCtrlEPList[i].hw_len = 0; +- TxCtrlEPList[i].command = (IO_STATE(USB_EP_command, eol, yes) | +- IO_FIELD(USB_EP_command, epid, i)); ++/* Cache for the data allocated in the isoc descr top half. */ ++static kmem_cache_t *isoc_compl_cache; + +- TxCtrlEPList[i].sub = 0; +- TxCtrlEPList[i].next = virt_to_phys(&TxCtrlEPList[0]); ++/* Cache for the data allocated when delayed finishing of URBs */ ++static kmem_cache_t *later_data_cache; + +- *R_DMA_CH8_SUB1_EP = virt_to_phys(&TxCtrlEPList[0]); +- *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start); + +- DBFEXIT; ++/* Counter to keep track of how many Isoc EP we have sat up. Used to enable ++ and disable iso_eof interrupt. We only need these interrupts when we have ++ Isoc data endpoints (consumes CPU cycles). ++ FIXME: This could be more fine granular, so this interrupt is only enabled ++ when we have a In Isoc URB not URB_ISO_ASAP flaged queued. */ ++static int isoc_epid_counter; ++ ++/* Protecting wrapper functions for R_USB_EPT_x */ ++/* -------------------------------------------- */ ++static inline void etrax_epid_set(__u8 index, __u32 data) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ *R_USB_EPT_DATA = data; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline void etrax_epid_clear_error(__u8 index) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ *R_USB_EPT_DATA &= ++ ~(IO_MASK(R_USB_EPT_DATA, error_count_in) | ++ IO_MASK(R_USB_EPT_DATA, error_count_out) | ++ IO_MASK(R_USB_EPT_DATA, error_code)); ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout, ++ __u8 toggle) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ if(dirout) { ++ *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_out); ++ *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_out, toggle); ++ } else { ++ *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_in); ++ *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_in, toggle); ++ } ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout) { ++ unsigned long flags; ++ __u8 toggle; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ if (dirout) { ++ toggle = IO_EXTRACT(R_USB_EPT_DATA, t_out, *R_USB_EPT_DATA); ++ } else { ++ toggle = IO_EXTRACT(R_USB_EPT_DATA, t_in, *R_USB_EPT_DATA); ++ } ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ return toggle; ++} ++ ++ ++static inline __u32 etrax_epid_get(__u8 index) { ++ unsigned long flags; ++ __u32 data; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ data = *R_USB_EPT_DATA; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ return data; ++} ++ ++ ++ ++ ++/* Main functions for Transfer Controller */ ++/* -------------------------------------- */ ++ ++/* Init structs, memories and lists used by Transfer Controller */ ++int tc_init(struct usb_hcd *hcd) { ++ int i; ++ /* Clear software state info for all epids */ ++ memset(epid_state, 0, sizeof(struct etrax_epid) * NBR_OF_EPIDS); ++ ++ /* Set Invalid and Dummy as being in use and disabled */ ++ epid_state[INVALID_EPID].inuse = 1; ++ epid_state[DUMMY_EPID].inuse = 1; ++ epid_state[INVALID_EPID].disabled = 1; ++ epid_state[DUMMY_EPID].disabled = 1; ++ ++ /* Clear counter for how many Isoc epids we have sat up */ ++ isoc_epid_counter = 0; ++ ++ /* Initialize the urb list by initiating a head for each list. ++ Also reset list hodling active URB for each epid */ ++ for (i = 0; i < NBR_OF_EPIDS; i++) { ++ INIT_LIST_HEAD(&urb_list[i]); ++ activeUrbList[i] = NULL; ++ } ++ ++ /* Init lock for URB lists */ ++ spin_lock_init(&urb_list_lock); ++ /* Init lock for Etrax R_USB_EPT register */ ++ spin_lock_init(&etrax_epid_lock); ++ /* Init lock for Etrax dma8 sub0 handling */ ++ spin_lock_init(&etrax_dma8_sub0_lock); ++ ++ /* We use kmem_cache_* to make sure that all DMA desc. are dword aligned */ ++ ++ /* Note that we specify sizeof(struct USB_EP_Desc) as the size, but also ++ allocate SB descriptors from this cache. This is ok since ++ sizeof(struct USB_EP_Desc) == sizeof(struct USB_SB_Desc). */ ++ usb_desc_cache = kmem_cache_create("usb_desc_cache", ++ sizeof(struct USB_EP_Desc), 0, ++ SLAB_HWCACHE_ALIGN, 0, 0); ++ if(usb_desc_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ /* Create slab cache for speedy allocation of memory for isoc bottom-half ++ interrupt handling */ ++ isoc_compl_cache = ++ kmem_cache_create("isoc_compl_cache", ++ sizeof(struct crisv10_isoc_complete_data), ++ 0, SLAB_HWCACHE_ALIGN, 0, 0); ++ if(isoc_compl_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ /* Create slab cache for speedy allocation of memory for later URB finish ++ struct */ ++ later_data_cache = ++ kmem_cache_create("later_data_cache", ++ sizeof(struct urb_later_data), ++ 0, SLAB_HWCACHE_ALIGN, 0, 0); ++ if(later_data_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ ++ /* Initiate the bulk start timer. */ ++ init_timer(&bulk_start_timer); ++ bulk_start_timer.expires = jiffies + BULK_START_TIMER_INTERVAL; ++ bulk_start_timer.function = tc_bulk_start_timer_func; ++ add_timer(&bulk_start_timer); ++ ++ ++ /* Initiate the bulk eot timer. */ ++ init_timer(&bulk_eot_timer); ++ bulk_eot_timer.expires = jiffies + BULK_EOT_TIMER_INTERVAL; ++ bulk_eot_timer.function = tc_bulk_eot_timer_func; ++ bulk_eot_timer.data = (unsigned long)hcd; ++ add_timer(&bulk_eot_timer); ++ ++ return 0; ++} ++ ++/* Uninitialize all resources used by Transfer Controller */ ++void tc_destroy(void) { ++ ++ /* Destroy all slab cache */ ++ kmem_cache_destroy(usb_desc_cache); ++ kmem_cache_destroy(isoc_compl_cache); ++ kmem_cache_destroy(later_data_cache); ++ ++ /* Remove timers */ ++ del_timer(&bulk_start_timer); ++ del_timer(&bulk_eot_timer); ++} ++ ++static void restart_dma8_sub0(void) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_dma8_sub0_lock, flags); ++ /* Verify that the dma is not running */ ++ if ((*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd)) == 0) { ++ struct USB_EP_Desc *ep = (struct USB_EP_Desc *)phys_to_virt(*R_DMA_CH8_SUB0_EP); ++ while (DUMMY_EPID == IO_EXTRACT(USB_EP_command, epid, ep->command)) { ++ ep = (struct USB_EP_Desc *)phys_to_virt(ep->next); ++ } ++ /* Advance the DMA to the next EP descriptor that is not a DUMMY_EPID. ++ * ep->next is already a physical address; no need for a virt_to_phys. */ ++ *R_DMA_CH8_SUB0_EP = ep->next; ++ /* Restart the DMA */ ++ *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); ++ } ++ spin_unlock_irqrestore(&etrax_dma8_sub0_lock, flags); ++} ++ ++/* queue an URB with the transfer controller (called from hcd_driver) */ ++static int tc_urb_enqueue(struct usb_hcd *hcd, ++ struct usb_host_endpoint *ep, ++ struct urb *urb, ++ gfp_t mem_flags) { ++ int epid; ++ int retval; ++ int bustime = 0; ++ int maxpacket; ++ unsigned long flags; ++ struct crisv10_urb_priv *urb_priv; ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ DBFENTER; ++ ++ if(!(crisv10_hcd->running)) { ++ /* The USB Controller is not running, probably because no device is ++ attached. No idea to enqueue URBs then */ ++ tc_warn("Rejected enqueueing of URB:0x%x because no dev attached\n", ++ (unsigned int)urb); ++ return -ENOENT; ++ } ++ ++ maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); ++ /* Special case check for In Isoc transfers. Specification states that each ++ In Isoc transfer consists of one packet and therefore it should fit into ++ the transfer-buffer of an URB. ++ We do the check here to be sure (an invalid scenario can be produced with ++ parameters to the usbtest suite) */ ++ if(usb_pipeisoc(urb->pipe) && usb_pipein(urb->pipe) && ++ (urb->transfer_buffer_length < maxpacket)) { ++ tc_err("Submit In Isoc URB with buffer length:%d to pipe with maxpacketlen: %d\n", urb->transfer_buffer_length, maxpacket); ++ return -EMSGSIZE; ++ } ++ ++ /* Check if there is enough bandwidth for periodic transfer */ ++ if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) { ++ /* only check (and later claim) if not already claimed */ ++ if (urb->bandwidth == 0) { ++ bustime = usb_check_bandwidth(urb->dev, urb); ++ if (bustime < 0) { ++ tc_err("Not enough periodic bandwidth\n"); ++ return -ENOSPC; ++ } ++ } ++ } ++ ++ /* Check if there is a epid for URBs destination, if not this function ++ set up one. */ ++ epid = tc_setup_epid(ep, urb, mem_flags); ++ if (epid < 0) { ++ tc_err("Failed setup epid:%d for URB:0x%x\n", epid, (unsigned int)urb); ++ DBFEXIT; ++ return -ENOMEM; ++ } ++ ++ if(urb == activeUrbList[epid]) { ++ tc_err("Resubmition of allready active URB:0x%x\n", (unsigned int)urb); ++ return -ENXIO; ++ } ++ ++ if(urb_list_entry(urb, epid)) { ++ tc_err("Resubmition of allready queued URB:0x%x\n", (unsigned int)urb); ++ return -ENXIO; ++ } ++ ++ /* If we actively have flaged endpoint as disabled then refuse submition */ ++ if(epid_state[epid].disabled) { ++ return -ENOENT; ++ } ++ ++ /* Allocate and init HC-private data for URB */ ++ if(urb_priv_create(hcd, urb, epid, mem_flags) != 0) { ++ DBFEXIT; ++ return -ENOMEM; ++ } ++ urb_priv = urb->hcpriv; ++ ++ tc_dbg("Enqueue URB:0x%x[%d] epid:%d (%s) bufflen:%d\n", ++ (unsigned int)urb, urb_priv->urb_num, epid, ++ pipe_to_str(urb->pipe), urb->transfer_buffer_length); ++ ++ /* Create and link SBs required for this URB */ ++ retval = create_sb_for_urb(urb, mem_flags); ++ if(retval != 0) { ++ tc_err("Failed to create SBs for URB:0x%x[%d]\n", (unsigned int)urb, ++ urb_priv->urb_num); ++ urb_priv_free(hcd, urb); ++ DBFEXIT; ++ return retval; ++ } ++ ++ /* Init intr EP pool if this URB is a INTR transfer. This pool is later ++ used when inserting EPs in the TxIntrEPList. We do the alloc here ++ so we can't run out of memory later */ ++ if(usb_pipeint(urb->pipe)) { ++ retval = init_intr_urb(urb, mem_flags); ++ if(retval != 0) { ++ tc_warn("Failed to init Intr URB\n"); ++ urb_priv_free(hcd, urb); ++ DBFEXIT; ++ return retval; ++ } ++ } ++ ++ /* Disable other access when inserting USB */ ++ local_irq_save(flags); ++ ++ /* Claim bandwidth, if needed */ ++ if(bustime) { ++ usb_claim_bandwidth(urb->dev, urb, bustime, 0); ++ } ++ ++ /* Add URB to EP queue */ ++ urb_list_add(urb, epid, mem_flags); ++ ++ if(usb_pipeisoc(urb->pipe)) { ++ /* Special processing of Isoc URBs. */ ++ tc_dma_process_isoc_urb(urb); ++ } else { ++ /* Process EP queue for rest of the URB types (Bulk, Ctrl, Intr) */ ++ tc_dma_process_queue(epid); ++ } ++ ++ local_irq_restore(flags); ++ ++ DBFEXIT; ++ return 0; ++} ++ ++/* remove an URB from the transfer controller queues (called from hcd_driver)*/ ++static int tc_urb_dequeue(struct usb_hcd *hcd, struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv; ++ unsigned long flags; ++ int epid; ++ ++ DBFENTER; ++ /* Disable interrupts here since a descriptor interrupt for the isoc epid ++ will modify the sb list. This could possibly be done more granular, but ++ urb_dequeue should not be used frequently anyway. ++ */ ++ local_irq_save(flags); ++ ++ urb_priv = urb->hcpriv; ++ ++ if (!urb_priv) { ++ /* This happens if a device driver calls unlink on an urb that ++ was never submitted (lazy driver) or if the urb was completed ++ while dequeue was being called. */ ++ tc_warn("Dequeing of not enqueued URB:0x%x\n", (unsigned int)urb); ++ local_irq_restore(flags); ++ return 0; ++ } ++ epid = urb_priv->epid; ++ ++ tc_warn("Dequeing %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ /* For Bulk, Ctrl and Intr are only one URB active at a time. So any URB ++ that isn't active can be dequeued by just removing it from the queue */ ++ if(usb_pipebulk(urb->pipe) || usb_pipecontrol(urb->pipe) || ++ usb_pipeint(urb->pipe)) { ++ ++ /* Check if URB haven't gone further than the queue */ ++ if(urb != activeUrbList[epid]) { ++ ASSERT(urb_priv->later_data == NULL); ++ tc_warn("Dequeing URB:0x%x[%d] (%s %s epid:%d) from queue" ++ " (not active)\n", (unsigned int)urb, urb_priv->urb_num, ++ str_dir(urb->pipe), str_type(urb->pipe), epid); ++ ++ /* Finish the URB with error status from USB core */ ++ tc_finish_urb(hcd, urb, urb->status); ++ local_irq_restore(flags); ++ return 0; ++ } ++ } ++ ++ /* Set URB status to Unlink for handling when interrupt comes. */ ++ urb_priv->urb_state = UNLINK; ++ ++ /* Differentiate dequeing of Bulk and Ctrl from Isoc and Intr */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Check if EP still is enabled */ ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ /* Kicking dummy list out of the party. */ ++ TxBulkEPList[epid].next = virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); ++ break; ++ case PIPE_CONTROL: ++ /* Check if EP still is enabled */ ++ if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ break; ++ case PIPE_ISOCHRONOUS: ++ /* Disabling, busy-wait and unlinking of Isoc SBs will be done in ++ finish_isoc_urb(). Because there might the case when URB is dequeued ++ but there are other valid URBs waiting */ ++ ++ /* Check if In Isoc EP still is enabled */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ break; ++ case PIPE_INTERRUPT: ++ /* Special care is taken for interrupt URBs. EPs are unlinked in ++ tc_finish_urb */ ++ break; ++ default: ++ break; ++ } ++ ++ /* Asynchronous unlink, finish the URB later from scheduled or other ++ event (data finished, error) */ ++ tc_finish_urb_later(hcd, urb, urb->status); ++ ++ local_irq_restore(flags); ++ DBFEXIT; ++ return 0; ++} ++ ++ ++static void tc_sync_finish_epid(struct usb_hcd *hcd, int epid) { ++ volatile int timeout = 10000; ++ struct urb* urb; ++ struct crisv10_urb_priv* urb_priv; ++ unsigned long flags; ++ ++ volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */ ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ ++ int type = epid_state[epid].type; ++ ++ /* Setting this flag will cause enqueue() to return -ENOENT for new ++ submitions on this endpoint and finish_urb() wont process queue further */ ++ epid_state[epid].disabled = 1; ++ ++ switch(type) { ++ case PIPE_BULK: ++ /* Check if EP still is enabled */ ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ tc_warn("sync_finish: Disabling EP for epid:%d\n", epid); ++ ++ /* Do busy-wait until DMA not using this EP descriptor anymore */ ++ while((*R_DMA_CH8_SUB0_EP == ++ virt_to_phys(&TxBulkEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Bulk to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ ++ case PIPE_CONTROL: ++ /* Check if EP still is enabled */ ++ if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ tc_warn("sync_finish: Disabling EP for epid:%d\n", epid); ++ ++ /* Do busy-wait until DMA not using this EP descriptor anymore */ ++ while((*R_DMA_CH8_SUB1_EP == ++ virt_to_phys(&TxCtrlEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Ctrl to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ ++ case PIPE_INTERRUPT: ++ local_irq_save(flags); ++ /* Disable all Intr EPs belonging to epid */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* Disable EP */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ local_irq_restore(flags); ++ break; ++ ++ case PIPE_ISOCHRONOUS: ++ /* Check if EP still is enabled */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ tc_warn("sync_finish: Disabling Isoc EP for epid:%d\n", epid); ++ /* The EP was enabled, disable it. */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ ++ while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Isoc to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ } ++ ++ local_irq_save(flags); ++ ++ /* Finish if there is active URB for this endpoint */ ++ if(activeUrbList[epid] != NULL) { ++ urb = activeUrbList[epid]; ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv); ++ tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ tc_finish_urb(hcd, activeUrbList[epid], -ENOENT); ++ ASSERT(activeUrbList[epid] == NULL); ++ } ++ ++ /* Finish any queued URBs for this endpoint. There won't be any resubmitions ++ because epid_disabled causes enqueue() to fail for this endpoint */ ++ while((urb = urb_list_first(epid)) != NULL) { ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ tc_finish_urb(hcd, urb, -ENOENT); ++ } ++ epid_state[epid].disabled = 0; ++ local_irq_restore(flags); ++} ++ ++/* free resources associated with an endpoint (called from hcd_driver) */ ++static void tc_endpoint_disable(struct usb_hcd *hcd, ++ struct usb_host_endpoint *ep) { ++ DBFENTER; ++ /* Only free epid if it has been allocated. We get two endpoint_disable ++ requests for ctrl endpoints so ignore the second one */ ++ if(ep->hcpriv != NULL) { ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ int epid = ep_priv->epid; ++ tc_warn("endpoint_disable ep:0x%x ep-priv:0x%x (%s) (epid:%d freed)\n", ++ (unsigned int)ep, (unsigned int)ep->hcpriv, ++ endpoint_to_str(&(ep->desc)), epid); ++ ++ tc_sync_finish_epid(hcd, epid); ++ ++ ASSERT(activeUrbList[epid] == NULL); ++ ASSERT(list_empty(&urb_list[epid])); ++ ++ tc_free_epid(ep); ++ } else { ++ tc_dbg("endpoint_disable ep:0x%x ep-priv:0x%x (%s)\n", (unsigned int)ep, ++ (unsigned int)ep->hcpriv, endpoint_to_str(&(ep->desc))); ++ } ++ DBFEXIT; ++} ++ ++static void tc_finish_urb_later_proc(void *data) { ++ unsigned long flags; ++ struct urb_later_data* uld = (struct urb_later_data*)data; ++ local_irq_save(flags); ++ if(uld->urb == NULL) { ++ late_dbg("Later finish of URB = NULL (allready finished)\n"); ++ } else { ++ struct crisv10_urb_priv* urb_priv = uld->urb->hcpriv; ++ ASSERT(urb_priv); ++ if(urb_priv->urb_num == uld->urb_num) { ++ late_dbg("Later finish of URB:0x%x[%d]\n", (unsigned int)(uld->urb), ++ urb_priv->urb_num); ++ if(uld->status != uld->urb->status) { ++ errno_dbg("Later-finish URB with status:%d, later-status:%d\n", ++ uld->urb->status, uld->status); ++ } ++ if(uld != urb_priv->later_data) { ++ panic("Scheduled uld not same as URBs uld\n"); ++ } ++ tc_finish_urb(uld->hcd, uld->urb, uld->status); ++ } else { ++ late_warn("Ignoring later finish of URB:0x%x[%d]" ++ ", urb_num doesn't match current URB:0x%x[%d]", ++ (unsigned int)(uld->urb), uld->urb_num, ++ (unsigned int)(uld->urb), urb_priv->urb_num); ++ } ++ } ++ local_irq_restore(flags); ++ kmem_cache_free(later_data_cache, uld); ++} ++ ++static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb, ++ int status) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ struct urb_later_data* uld; ++ ++ ASSERT(urb_priv); ++ ++ if(urb_priv->later_data != NULL) { ++ /* Later-finish allready scheduled for this URB, just update status to ++ return when finishing later */ ++ errno_dbg("Later-finish schedule change URB status:%d with new" ++ " status:%d\n", urb_priv->later_data->status, status); ++ ++ urb_priv->later_data->status = status; ++ return; ++ } ++ ++ uld = kmem_cache_alloc(later_data_cache, SLAB_ATOMIC); ++ ASSERT(uld); ++ ++ uld->hcd = hcd; ++ uld->urb = urb; ++ uld->urb_num = urb_priv->urb_num; ++ uld->status = status; ++ ++ INIT_WORK(&uld->ws, tc_finish_urb_later_proc, uld); ++ urb_priv->later_data = uld; ++ ++ /* Schedule the finishing of the URB to happen later */ ++ schedule_delayed_work(&uld->ws, LATER_TIMER_DELAY); ++} ++ ++static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb, ++ int status); ++ ++static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status) { ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid; ++ char toggle; ++ int urb_num; ++ ++ DBFENTER; ++ ASSERT(urb_priv != NULL); ++ epid = urb_priv->epid; ++ urb_num = urb_priv->urb_num; ++ ++ if(urb != activeUrbList[epid]) { ++ if(urb_list_entry(urb, epid)) { ++ /* Remove this URB from the list. Only happens when URB are finished ++ before having been processed (dequeing) */ ++ urb_list_del(urb, epid); ++ } else { ++ tc_warn("Finishing of URB:0x%x[%d] neither active or in queue for" ++ " epid:%d\n", (unsigned int)urb, urb_num, epid); ++ } ++ } ++ ++ /* Cancel any pending later-finish of this URB */ ++ if(urb_priv->later_data) { ++ urb_priv->later_data->urb = NULL; ++ } ++ ++ /* For an IN pipe, we always set the actual length, regardless of whether ++ there was an error or not (which means the device driver can use the data ++ if it wants to). */ ++ if(usb_pipein(urb->pipe)) { ++ urb->actual_length = urb_priv->rx_offset; ++ } else { ++ /* Set actual_length for OUT urbs also; the USB mass storage driver seems ++ to want that. */ ++ if (status == 0 && urb->status == -EINPROGRESS) { ++ urb->actual_length = urb->transfer_buffer_length; ++ } else { ++ /* We wouldn't know of any partial writes if there was an error. */ ++ urb->actual_length = 0; ++ } ++ } ++ ++ ++ /* URB status mangling */ ++ if(urb->status == -EINPROGRESS) { ++ /* The USB core hasn't changed the status, let's set our finish status */ ++ urb->status = status; ++ ++ if ((status == 0) && (urb->transfer_flags & URB_SHORT_NOT_OK) && ++ usb_pipein(urb->pipe) && ++ (urb->actual_length != urb->transfer_buffer_length)) { ++ /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's ++ max length) is to be treated as an error. */ ++ errno_dbg("Finishing URB:0x%x[%d] with SHORT_NOT_OK flag and short" ++ " data:%d\n", (unsigned int)urb, urb_num, ++ urb->actual_length); ++ urb->status = -EREMOTEIO; ++ } ++ ++ if(urb_priv->urb_state == UNLINK) { ++ /* URB has been requested to be unlinked asynchronously */ ++ urb->status = -ECONNRESET; ++ errno_dbg("Fixing unlink status of URB:0x%x[%d] to:%d\n", ++ (unsigned int)urb, urb_num, urb->status); ++ } ++ } else { ++ /* The USB Core wants to signal some error via the URB, pass it through */ ++ } ++ ++ /* use completely different finish function for Isoc URBs */ ++ if(usb_pipeisoc(urb->pipe)) { ++ tc_finish_isoc_urb(hcd, urb, status); ++ return; ++ } ++ ++ /* Do special unlinking of EPs for Intr traffic */ ++ if(usb_pipeint(urb->pipe)) { ++ tc_dma_unlink_intr_urb(urb); ++ } ++ ++ /* Release allocated bandwidth for periodic transfers */ ++ if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) ++ usb_release_bandwidth(urb->dev, urb, 0); ++ ++ /* This URB is active on EP */ ++ if(urb == activeUrbList[epid]) { ++ /* We need to fiddle with the toggle bits because the hardware doesn't do ++ it for us. */ ++ toggle = etrax_epid_get_toggle(epid, usb_pipeout(urb->pipe)); ++ usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe), ++ usb_pipeout(urb->pipe), toggle); ++ ++ /* Checks for Ctrl and Bulk EPs */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Check so Bulk EP realy is disabled before finishing active URB */ ++ ASSERT((TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) == ++ IO_STATE(USB_EP_command, enable, no)); ++ /* Disable sub-pointer for EP to avoid next tx_interrupt() to ++ process Bulk EP. */ ++ TxBulkEPList[epid].sub = 0; ++ /* No need to wait for the DMA before changing the next pointer. ++ The modulo NBR_OF_EPIDS isn't actually necessary, since we will never use ++ the last one (INVALID_EPID) for actual traffic. */ ++ TxBulkEPList[epid].next = ++ virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); ++ break; ++ case PIPE_CONTROL: ++ /* Check so Ctrl EP realy is disabled before finishing active URB */ ++ ASSERT((TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) == ++ IO_STATE(USB_EP_command, enable, no)); ++ /* Disable sub-pointer for EP to avoid next tx_interrupt() to ++ process Ctrl EP. */ ++ TxCtrlEPList[epid].sub = 0; ++ break; ++ } ++ } ++ ++ /* Free HC-private URB data*/ ++ urb_priv_free(hcd, urb); ++ ++ if(urb->status) { ++ errno_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n", ++ (unsigned int)urb, urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb->actual_length, urb->status); ++ } else { ++ tc_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n", ++ (unsigned int)urb, urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb->actual_length, urb->status); ++ } ++ ++ /* If we just finished an active URB, clear active pointer. */ ++ if (urb == activeUrbList[epid]) { ++ /* Make URB not active on EP anymore */ ++ activeUrbList[epid] = NULL; ++ ++ if(urb->status == 0) { ++ /* URB finished sucessfully, process queue to see if there are any more ++ URBs waiting before we call completion function.*/ ++ if(crisv10_hcd->running) { ++ /* Only process queue if USB controller is running */ ++ tc_dma_process_queue(epid); ++ } else { ++ tc_warn("No processing of queue for epid:%d, USB Controller not" ++ " running\n", epid); ++ } ++ } ++ } ++ ++ /* Hand the URB from HCD to its USB device driver, using its completion ++ functions */ ++ usb_hcd_giveback_urb (hcd, urb); ++ ++ /* Check the queue once more if the URB returned with error, because we ++ didn't do it before the completion function because the specification ++ states that the queue should not restart until all it's unlinked ++ URBs have been fully retired, with the completion functions run */ ++ if(crisv10_hcd->running) { ++ /* Only process queue if USB controller is running */ ++ tc_dma_process_queue(epid); ++ } else { ++ tc_warn("No processing of queue for epid:%d, USB Controller not running\n", ++ epid); ++ } ++ ++ DBFEXIT; ++} ++ ++static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb, ++ int status) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid, i; ++ volatile int timeout = 10000; ++ ++ ASSERT(urb_priv); ++ epid = urb_priv->epid; ++ ++ ASSERT(usb_pipeisoc(urb->pipe)); ++ ++ /* Set that all isoc packets have status and length set before ++ completing the urb. */ ++ for (i = urb_priv->isoc_packet_counter; i < urb->number_of_packets; i++){ ++ urb->iso_frame_desc[i].actual_length = 0; ++ urb->iso_frame_desc[i].status = -EPROTO; ++ } ++ ++ /* Check if the URB is currently active (done or error) */ ++ if(urb == activeUrbList[epid]) { ++ /* Check if there are another In Isoc URB queued for this epid */ ++ if (!list_empty(&urb_list[epid])&& !epid_state[epid].disabled) { ++ /* Move it from queue to active and mark it started so Isoc transfers ++ won't be interrupted. ++ All Isoc URBs data transfers are already added to DMA lists so we ++ don't have to insert anything in DMA lists here. */ ++ activeUrbList[epid] = urb_list_first(epid); ++ ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_state = ++ STARTED; ++ urb_list_del(activeUrbList[epid], epid); ++ ++ if(urb->status) { ++ errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)" ++ " status:%d, new waiting URB:0x%x[%d]\n", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb_priv->isoc_packet_counter, ++ urb->number_of_packets, urb->status, ++ (unsigned int)activeUrbList[epid], ++ ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_num); ++ } ++ ++ } else { /* No other URB queued for this epid */ ++ if(urb->status) { ++ errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)" ++ " status:%d, no new URB waiting\n", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb_priv->isoc_packet_counter, ++ urb->number_of_packets, urb->status); ++ } ++ ++ /* Check if EP is still enabled, then shut it down. */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ isoc_dbg("Isoc EP enabled for epid:%d, disabling it\n", epid); ++ ++ /* Should only occur for In Isoc EPs where SB isn't consumed. */ ++ ASSERT(usb_pipein(urb->pipe)); ++ ++ /* Disable it and wait for it to stop */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ ++ /* Ah, the luxury of busy-wait. */ ++ while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Isoc to leave EP for epid:%d\n", epid); ++ } ++ } ++ ++ /* Unlink SB to say that epid is finished. */ ++ TxIsocEPList[epid].sub = 0; ++ TxIsocEPList[epid].hw_len = 0; ++ ++ /* No URB active for EP anymore */ ++ activeUrbList[epid] = NULL; ++ } ++ } else { /* Finishing of not active URB (queued up with SBs thought) */ ++ isoc_warn("finish_isoc_urb (URB:0x%x %s) (%d of %d packets) status:%d," ++ " SB queued but not active\n", ++ (unsigned int)urb, str_dir(urb->pipe), ++ urb_priv->isoc_packet_counter, urb->number_of_packets, ++ urb->status); ++ if(usb_pipeout(urb->pipe)) { ++ /* Finishing of not yet active Out Isoc URB needs unlinking of SBs. */ ++ struct USB_SB_Desc *iter_sb, *prev_sb, *next_sb; ++ ++ iter_sb = TxIsocEPList[epid].sub ? ++ phys_to_virt(TxIsocEPList[epid].sub) : 0; ++ prev_sb = 0; ++ ++ /* SB that is linked before this URBs first SB */ ++ while (iter_sb && (iter_sb != urb_priv->first_sb)) { ++ prev_sb = iter_sb; ++ iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } ++ ++ if (iter_sb == 0) { ++ /* Unlink of the URB currently being transmitted. */ ++ prev_sb = 0; ++ iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0; ++ } ++ ++ while (iter_sb && (iter_sb != urb_priv->last_sb)) { ++ iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } ++ ++ if (iter_sb) { ++ next_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } else { ++ /* This should only happen if the DMA has completed ++ processing the SB list for this EP while interrupts ++ are disabled. */ ++ isoc_dbg("Isoc urb not found, already sent?\n"); ++ next_sb = 0; ++ } ++ if (prev_sb) { ++ prev_sb->next = next_sb ? virt_to_phys(next_sb) : 0; ++ } else { ++ TxIsocEPList[epid].sub = next_sb ? virt_to_phys(next_sb) : 0; ++ } ++ } ++ } ++ ++ /* Free HC-private URB data*/ ++ urb_priv_free(hcd, urb); ++ ++ usb_release_bandwidth(urb->dev, urb, 0); ++ ++ /* Hand the URB from HCD to its USB device driver, using its completion ++ functions */ ++ usb_hcd_giveback_urb (hcd, urb); ++} ++ ++static __u32 urb_num = 0; ++ ++/* allocate and initialize URB private data */ ++static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid, ++ int mem_flags) { ++ struct crisv10_urb_priv *urb_priv; ++ ++ urb_priv = kmalloc(sizeof *urb_priv, mem_flags); ++ if (!urb_priv) ++ return -ENOMEM; ++ memset(urb_priv, 0, sizeof *urb_priv); ++ ++ urb_priv->epid = epid; ++ urb_priv->urb_state = NOT_STARTED; ++ ++ urb->hcpriv = urb_priv; ++ /* Assign URB a sequence number, and increment counter */ ++ urb_priv->urb_num = urb_num; ++ urb_num++; ++ return 0; ++} ++ ++/* free URB private data */ ++static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb) { ++ int i; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ ASSERT(urb_priv != 0); ++ ++ /* Check it has any SBs linked that needs to be freed*/ ++ if(urb_priv->first_sb != NULL) { ++ struct USB_SB_Desc *next_sb, *first_sb, *last_sb; ++ int i = 0; ++ first_sb = urb_priv->first_sb; ++ last_sb = urb_priv->last_sb; ++ ASSERT(last_sb); ++ while(first_sb != last_sb) { ++ next_sb = (struct USB_SB_Desc *)phys_to_virt(first_sb->next); ++ kmem_cache_free(usb_desc_cache, first_sb); ++ first_sb = next_sb; ++ i++; ++ } ++ kmem_cache_free(usb_desc_cache, last_sb); ++ i++; ++ } ++ ++ /* Check if it has any EPs in its Intr pool that also needs to be freed */ ++ if(urb_priv->intr_ep_pool_length > 0) { ++ for(i = 0; i < urb_priv->intr_ep_pool_length; i++) { ++ kfree(urb_priv->intr_ep_pool[i]); ++ } ++ /* ++ tc_dbg("Freed %d EPs from URB:0x%x EP pool\n", ++ urb_priv->intr_ep_pool_length, (unsigned int)urb); ++ */ ++ } ++ ++ kfree(urb_priv); ++ urb->hcpriv = NULL; ++} ++ ++static int ep_priv_create(struct usb_host_endpoint *ep, int mem_flags) { ++ struct crisv10_ep_priv *ep_priv; ++ ++ ep_priv = kmalloc(sizeof *ep_priv, mem_flags); ++ if (!ep_priv) ++ return -ENOMEM; ++ memset(ep_priv, 0, sizeof *ep_priv); ++ ++ ep->hcpriv = ep_priv; ++ return 0; ++} ++ ++static void ep_priv_free(struct usb_host_endpoint *ep) { ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ ASSERT(ep_priv); ++ kfree(ep_priv); ++ ep->hcpriv = NULL; ++} ++ ++/* EPID handling functions, managing EP-list in Etrax through wrappers */ ++/* ------------------------------------------------------------------- */ ++ ++/* Sets up a new EPID for an endpoint or returns existing if found */ ++static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb, ++ int mem_flags) { ++ int epid; ++ char devnum, endpoint, out_traffic, slow; ++ int maxlen; ++ __u32 epid_data; ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ ++ DBFENTER; ++ ++ /* Check if a valid epid already is setup for this endpoint */ ++ if(ep_priv != NULL) { ++ return ep_priv->epid; ++ } ++ ++ /* We must find and initiate a new epid for this urb. */ ++ epid = tc_allocate_epid(); ++ ++ if (epid == -1) { ++ /* Failed to allocate a new epid. */ ++ DBFEXIT; ++ return epid; ++ } ++ ++ /* We now have a new epid to use. Claim it. */ ++ epid_state[epid].inuse = 1; ++ ++ /* Init private data for new endpoint */ ++ if(ep_priv_create(ep, mem_flags) != 0) { ++ return -ENOMEM; ++ } ++ ep_priv = ep->hcpriv; ++ ep_priv->epid = epid; ++ ++ devnum = usb_pipedevice(urb->pipe); ++ endpoint = usb_pipeendpoint(urb->pipe); ++ slow = (urb->dev->speed == USB_SPEED_LOW); ++ maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); ++ ++ if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { ++ /* We want both IN and OUT control traffic to be put on the same ++ EP/SB list. */ ++ out_traffic = 1; ++ } else { ++ out_traffic = usb_pipeout(urb->pipe); ++ } ++ ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ epid_data = IO_STATE(R_USB_EPT_DATA_ISO, valid, yes) | ++ /* FIXME: Change any to the actual port? */ ++ IO_STATE(R_USB_EPT_DATA_ISO, port, any) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, max_len, maxlen) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, ep, endpoint) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, dev, devnum); ++ etrax_epid_iso_set(epid, epid_data); ++ } else { ++ epid_data = IO_STATE(R_USB_EPT_DATA, valid, yes) | ++ IO_FIELD(R_USB_EPT_DATA, low_speed, slow) | ++ /* FIXME: Change any to the actual port? */ ++ IO_STATE(R_USB_EPT_DATA, port, any) | ++ IO_FIELD(R_USB_EPT_DATA, max_len, maxlen) | ++ IO_FIELD(R_USB_EPT_DATA, ep, endpoint) | ++ IO_FIELD(R_USB_EPT_DATA, dev, devnum); ++ etrax_epid_set(epid, epid_data); ++ } ++ ++ epid_state[epid].out_traffic = out_traffic; ++ epid_state[epid].type = usb_pipetype(urb->pipe); ++ ++ tc_warn("Setting up ep:0x%x epid:%d (addr:%d endp:%d max_len:%d %s %s %s)\n", ++ (unsigned int)ep, epid, devnum, endpoint, maxlen, ++ str_type(urb->pipe), out_traffic ? "out" : "in", ++ slow ? "low" : "full"); ++ ++ /* Enable Isoc eof interrupt if we set up the first Isoc epid */ ++ if(usb_pipeisoc(urb->pipe)) { ++ isoc_epid_counter++; ++ if(isoc_epid_counter == 1) { ++ isoc_warn("Enabled Isoc eof interrupt\n"); ++ *R_USB_IRQ_MASK_SET |= IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set); ++ } ++ } ++ ++ DBFEXIT; ++ return epid; ++} ++ ++static void tc_free_epid(struct usb_host_endpoint *ep) { ++ unsigned long flags; ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ int epid; ++ volatile int timeout = 10000; ++ ++ DBFENTER; ++ ++ if (ep_priv == NULL) { ++ tc_warn("Trying to free unused epid on ep:0x%x\n", (unsigned int)ep); ++ DBFEXIT; ++ return; ++ } ++ ++ epid = ep_priv->epid; ++ ++ /* Disable Isoc eof interrupt if we free the last Isoc epid */ ++ if(epid_isoc(epid)) { ++ ASSERT(isoc_epid_counter > 0); ++ isoc_epid_counter--; ++ if(isoc_epid_counter == 0) { ++ *R_USB_IRQ_MASK_SET &= ~IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set); ++ isoc_warn("Disabled Isoc eof interrupt\n"); ++ } ++ } ++ ++ /* Take lock manualy instead of in epid_x_x wrappers, ++ because we need to be polling here */ ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ while((*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for epid:%d to drop hold\n", epid); ++ } ++ /* This will, among other things, set the valid field to 0. */ ++ *R_USB_EPT_DATA = 0; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ ++ /* Free resource in software state info list */ ++ epid_state[epid].inuse = 0; ++ ++ /* Free private endpoint data */ ++ ep_priv_free(ep); ++ ++ DBFEXIT; ++} ++ ++static int tc_allocate_epid(void) { ++ int i; ++ DBFENTER; ++ for (i = 0; i < NBR_OF_EPIDS; i++) { ++ if (!epid_inuse(i)) { ++ DBFEXIT; ++ return i; ++ } ++ } ++ ++ tc_warn("Found no free epids\n"); ++ DBFEXIT; ++ return -1; + } + + +-static void init_tx_intr_ep(void) +-{ +- int i; ++/* Wrappers around the list functions (include/linux/list.h). */ ++/* ---------------------------------------------------------- */ ++static inline int __urb_list_empty(int epid) { ++ int retval; ++ retval = list_empty(&urb_list[epid]); ++ return retval; ++} + +- DBFENTER; ++/* Returns first urb for this epid, or NULL if list is empty. */ ++static inline struct urb *urb_list_first(int epid) { ++ unsigned long flags; ++ struct urb *first_urb = 0; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ if (!__urb_list_empty(epid)) { ++ /* Get the first urb (i.e. head->next). */ ++ urb_entry_t *urb_entry = list_entry((&urb_list[epid])->next, urb_entry_t, list); ++ first_urb = urb_entry->urb; ++ } ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return first_urb; ++} + +- /* Read comment at zout_buffer declaration for an explanation to this. */ +- TxIntrSB_zout.sw_len = 1; +- TxIntrSB_zout.next = 0; +- TxIntrSB_zout.buf = virt_to_phys(&zout_buffer[0]); +- TxIntrSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, zout) | +- IO_STATE(USB_SB_command, full, yes) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- for (i = 0; i < (MAX_INTR_INTERVAL - 1); i++) { +- CHECK_ALIGN(&TxIntrEPList[i]); +- TxIntrEPList[i].hw_len = 0; +- TxIntrEPList[i].command = +- (IO_STATE(USB_EP_command, eof, yes) | +- IO_STATE(USB_EP_command, enable, yes) | +- IO_FIELD(USB_EP_command, epid, INVALID_EPID)); +- TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); +- TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[i + 1]); +- } ++/* Adds an urb_entry last in the list for this epid. */ ++static inline void urb_list_add(struct urb *urb, int epid, int mem_flags) { ++ unsigned long flags; ++ urb_entry_t *urb_entry = (urb_entry_t *)kmalloc(sizeof(urb_entry_t), mem_flags); ++ ASSERT(urb_entry); ++ ++ urb_entry->urb = urb; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ list_add_tail(&urb_entry->list, &urb_list[epid]); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++} + +- CHECK_ALIGN(&TxIntrEPList[i]); +- TxIntrEPList[i].hw_len = 0; +- TxIntrEPList[i].command = +- (IO_STATE(USB_EP_command, eof, yes) | +- IO_STATE(USB_EP_command, eol, yes) | +- IO_STATE(USB_EP_command, enable, yes) | +- IO_FIELD(USB_EP_command, epid, INVALID_EPID)); +- TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); +- TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[0]); +- +- *R_DMA_CH8_SUB2_EP = virt_to_phys(&TxIntrEPList[0]); +- *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start); +- DBFEXIT; ++/* Search through the list for an element that contains this urb. (The list ++ is expected to be short and the one we are about to delete will often be ++ the first in the list.) ++ Should be protected by spin_locks in calling function */ ++static inline urb_entry_t *__urb_list_entry(struct urb *urb, int epid) { ++ struct list_head *entry; ++ struct list_head *tmp; ++ urb_entry_t *urb_entry; ++ ++ list_for_each_safe(entry, tmp, &urb_list[epid]) { ++ urb_entry = list_entry(entry, urb_entry_t, list); ++ ASSERT(urb_entry); ++ ASSERT(urb_entry->urb); ++ ++ if (urb_entry->urb == urb) { ++ return urb_entry; ++ } ++ } ++ return 0; ++} ++ ++/* Same function as above but for global use. Protects list by spinlock */ ++static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return (urb_entry); + } + +-static void init_tx_isoc_ep(void) +-{ +- int i; ++/* Delete an urb from the list. */ ++static inline void urb_list_del(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ /* Delete entry and free. */ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ list_del(&urb_entry->list); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ kfree(urb_entry); ++} + +- DBFENTER; ++/* Move an urb to the end of the list. */ ++static inline void urb_list_move_last(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ list_del(&urb_entry->list); ++ list_add_tail(&urb_entry->list, &urb_list[epid]); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++} + +- /* Read comment at zout_buffer declaration for an explanation to this. */ +- TxIsocSB_zout.sw_len = 1; +- TxIsocSB_zout.next = 0; +- TxIsocSB_zout.buf = virt_to_phys(&zout_buffer[0]); +- TxIsocSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, zout) | +- IO_STATE(USB_SB_command, full, yes) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- /* The last isochronous EP descriptor is a dummy. */ +- +- for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { +- CHECK_ALIGN(&TxIsocEPList[i]); +- TxIsocEPList[i].hw_len = 0; +- TxIsocEPList[i].command = IO_FIELD(USB_EP_command, epid, i); +- TxIsocEPList[i].sub = 0; +- TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[i + 1]); ++/* Get the next urb in the list. */ ++static inline struct urb *urb_list_next(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ if (urb_entry->list.next != &urb_list[epid]) { ++ struct list_head *elem = urb_entry->list.next; ++ urb_entry = list_entry(elem, urb_entry_t, list); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return urb_entry->urb; ++ } else { ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return NULL; ++ } ++} ++ ++struct USB_EP_Desc* create_ep(int epid, struct USB_SB_Desc* sb_desc, ++ int mem_flags) { ++ struct USB_EP_Desc *ep_desc; ++ ep_desc = (struct USB_EP_Desc *) kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(ep_desc == NULL) ++ return NULL; ++ memset(ep_desc, 0, sizeof(struct USB_EP_Desc)); ++ ++ ep_desc->hw_len = 0; ++ ep_desc->command = (IO_FIELD(USB_EP_command, epid, epid) | ++ IO_STATE(USB_EP_command, enable, yes)); ++ if(sb_desc == NULL) { ++ ep_desc->sub = 0; ++ } else { ++ ep_desc->sub = virt_to_phys(sb_desc); ++ } ++ return ep_desc; ++} ++ ++#define TT_ZOUT 0 ++#define TT_IN 1 ++#define TT_OUT 2 ++#define TT_SETUP 3 ++ ++#define CMD_EOL IO_STATE(USB_SB_command, eol, yes) ++#define CMD_INTR IO_STATE(USB_SB_command, intr, yes) ++#define CMD_FULL IO_STATE(USB_SB_command, full, yes) ++ ++/* Allocation and setup of a generic SB. Used to create SETUP, OUT and ZOUT ++ SBs. Also used by create_sb_in() to avoid same allocation procedure at two ++ places */ ++struct USB_SB_Desc* create_sb(struct USB_SB_Desc* sb_prev, int tt, void* data, ++ int datalen, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ memset(sb_desc, 0, sizeof(struct USB_SB_Desc)); ++ ++ sb_desc->command = IO_FIELD(USB_SB_command, tt, tt) | ++ IO_STATE(USB_SB_command, eot, yes); ++ ++ sb_desc->sw_len = datalen; ++ if(data != NULL) { ++ sb_desc->buf = virt_to_phys(data); ++ } else { ++ sb_desc->buf = 0; ++ } ++ if(sb_prev != NULL) { ++ sb_prev->next = virt_to_phys(sb_desc); ++ } ++ return sb_desc; ++} ++ ++/* Creates a copy of an existing SB by allocation space for it and copy ++ settings */ ++struct USB_SB_Desc* create_sb_copy(struct USB_SB_Desc* sb_orig, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ ++ memcpy(sb_desc, sb_orig, sizeof(struct USB_SB_Desc)); ++ return sb_desc; ++} ++ ++/* A specific create_sb function for creation of in SBs. This is due to ++ that datalen in In SBs shows how many packets we are expecting. It also ++ sets up the rem field to show if how many bytes we expect in last packet ++ if it's not a full one */ ++struct USB_SB_Desc* create_sb_in(struct USB_SB_Desc* sb_prev, int datalen, ++ int maxlen, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = create_sb(sb_prev, TT_IN, NULL, ++ datalen ? (datalen - 1) / maxlen + 1 : 0, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ sb_desc->command |= IO_FIELD(USB_SB_command, rem, datalen % maxlen); ++ return sb_desc; ++} ++ ++void set_sb_cmds(struct USB_SB_Desc *sb_desc, __u16 flags) { ++ sb_desc->command |= flags; ++} ++ ++int create_sb_for_urb(struct urb *urb, int mem_flags) { ++ int is_out = !usb_pipein(urb->pipe); ++ int type = usb_pipetype(urb->pipe); ++ int maxlen = usb_maxpacket(urb->dev, urb->pipe, is_out); ++ int buf_len = urb->transfer_buffer_length; ++ void *buf = buf_len > 0 ? urb->transfer_buffer : NULL; ++ struct USB_SB_Desc *sb_desc = NULL; ++ ++ struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv != NULL); ++ ++ switch(type) { ++ case PIPE_CONTROL: ++ /* Setup stage */ ++ sb_desc = create_sb(NULL, TT_SETUP, urb->setup_packet, 8, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ ++ /* Attach first SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ ++ if (is_out) { /* Out Control URB */ ++ /* If this Control OUT transfer has an optional data stage we add ++ an OUT token before the mandatory IN (status) token */ ++ if ((buf_len > 0) && buf) { ++ sb_desc = create_sb(sb_desc, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ ++ /* Status stage */ ++ /* The data length has to be exactly 1. This is due to a requirement ++ of the USB specification that a host must be prepared to receive ++ data in the status phase */ ++ sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } else { /* In control URB */ ++ /* Data stage */ ++ sb_desc = create_sb_in(sb_desc, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* Status stage */ ++ /* Read comment at zout_buffer declaration for an explanation to this. */ ++ sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* Set descriptor interrupt flag for in URBs so we can finish URB after ++ zout-packet has been sent */ ++ set_sb_cmds(sb_desc, CMD_INTR | CMD_FULL); ++ } ++ /* Set end-of-list flag in last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ /* Attach last SB to URB */ ++ urb_priv->last_sb = sb_desc; ++ break; ++ ++ case PIPE_BULK: ++ if (is_out) { /* Out Bulk URB */ ++ sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* The full field is set to yes, even if we don't actually check that ++ this is a full-length transfer (i.e., that transfer_buffer_length % ++ maxlen = 0). ++ Setting full prevents the USB controller from sending an empty packet ++ in that case. However, if URB_ZERO_PACKET was set we want that. */ ++ if (!(urb->transfer_flags & URB_ZERO_PACKET)) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ } else { /* In Bulk URB */ ++ sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } ++ /* Set end-of-list flag for last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ break; ++ ++ case PIPE_INTERRUPT: ++ if(is_out) { /* Out Intr URB */ ++ sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* The full field is set to yes, even if we don't actually check that ++ this is a full-length transfer (i.e., that transfer_buffer_length % ++ maxlen = 0). ++ Setting full prevents the USB controller from sending an empty packet ++ in that case. However, if URB_ZERO_PACKET was set we want that. */ ++ if (!(urb->transfer_flags & URB_ZERO_PACKET)) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ /* Only generate TX interrupt if it's a Out URB*/ ++ set_sb_cmds(sb_desc, CMD_INTR); ++ ++ } else { /* In Intr URB */ ++ sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } ++ /* Set end-of-list flag for last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ ++ break; ++ case PIPE_ISOCHRONOUS: ++ if(is_out) { /* Out Isoc URB */ ++ int i; ++ if(urb->number_of_packets == 0) { ++ tc_err("Can't create SBs for Isoc URB with zero packets\n"); ++ return -EPIPE; ++ } ++ /* Create one SB descriptor for each packet and link them together. */ ++ for(i = 0; i < urb->number_of_packets; i++) { ++ if (urb->iso_frame_desc[i].length > 0) { ++ ++ sb_desc = create_sb(sb_desc, TT_OUT, urb->transfer_buffer + ++ urb->iso_frame_desc[i].offset, ++ urb->iso_frame_desc[i].length, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* Check if it's a full length packet */ ++ if (urb->iso_frame_desc[i].length == ++ usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ ++ } else { /* zero length packet */ ++ sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ /* Attach first SB descriptor to URB */ ++ if (i == 0) { ++ urb_priv->first_sb = sb_desc; ++ } ++ } ++ /* Set interrupt and end-of-list flags in last SB */ ++ set_sb_cmds(sb_desc, CMD_INTR | CMD_EOL); ++ /* Attach last SB descriptor to URB */ ++ urb_priv->last_sb = sb_desc; ++ tc_dbg("Created %d out SBs for Isoc URB:0x%x\n", ++ urb->number_of_packets, (unsigned int)urb); ++ } else { /* In Isoc URB */ ++ /* Actual number of packets is not relevant for periodic in traffic as ++ long as it is more than zero. Set to 1 always. */ ++ sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* Set end-of-list flags for SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ } ++ break; ++ default: ++ tc_err("Unknown pipe-type\n"); ++ return -EPIPE; ++ break; ++ } ++ return 0; ++} ++ ++int init_intr_urb(struct urb *urb, int mem_flags) { ++ struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ struct USB_EP_Desc* ep_desc; ++ int interval; ++ int i; ++ int ep_count; ++ ++ ASSERT(urb_priv != NULL); ++ ASSERT(usb_pipeint(urb->pipe)); ++ /* We can't support interval longer than amount of eof descriptors in ++ TxIntrEPList */ ++ if(urb->interval > MAX_INTR_INTERVAL) { ++ tc_err("Interrupt interval %dms too big (max: %dms)\n", urb->interval, ++ MAX_INTR_INTERVAL); ++ return -EINVAL; ++ } ++ ++ /* We assume that the SB descriptors already have been setup */ ++ ASSERT(urb_priv->first_sb != NULL); ++ ++ /* Round of the interval to 2^n, it is obvious that this code favours ++ smaller numbers, but that is actually a good thing */ ++ /* FIXME: The "rounding error" for larger intervals will be quite ++ large. For in traffic this shouldn't be a problem since it will only ++ mean that we "poll" more often. */ ++ interval = urb->interval; ++ for (i = 0; interval; i++) { ++ interval = interval >> 1; ++ } ++ urb_priv->interval = 1 << (i - 1); ++ ++ /* We can only have max interval for Out Interrupt due to that we can only ++ handle one linked in EP for a certain epid in the Intr descr array at the ++ time. The USB Controller in the Etrax 100LX continues to process Intr EPs ++ so we have no way of knowing which one that caused the actual transfer if ++ we have several linked in. */ ++ if(usb_pipeout(urb->pipe)) { ++ urb_priv->interval = MAX_INTR_INTERVAL; ++ } ++ ++ /* Calculate amount of EPs needed */ ++ ep_count = MAX_INTR_INTERVAL / urb_priv->interval; ++ ++ for(i = 0; i < ep_count; i++) { ++ ep_desc = create_ep(urb_priv->epid, urb_priv->first_sb, mem_flags); ++ if(ep_desc == NULL) { ++ /* Free any descriptors that we may have allocated before failure */ ++ while(i > 0) { ++ i--; ++ kfree(urb_priv->intr_ep_pool[i]); ++ } ++ return -ENOMEM; ++ } ++ urb_priv->intr_ep_pool[i] = ep_desc; ++ } ++ urb_priv->intr_ep_pool_length = ep_count; ++ return 0; ++} ++ ++/* DMA RX/TX functions */ ++/* ----------------------- */ ++ ++static void tc_dma_init_rx_list(void) { ++ int i; ++ ++ /* Setup descriptor list except last one */ ++ for (i = 0; i < (NBR_OF_RX_DESC - 1); i++) { ++ RxDescList[i].sw_len = RX_DESC_BUF_SIZE; ++ RxDescList[i].command = 0; ++ RxDescList[i].next = virt_to_phys(&RxDescList[i + 1]); ++ RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); ++ RxDescList[i].hw_len = 0; ++ RxDescList[i].status = 0; ++ ++ /* DMA IN cache bug. (struct etrax_dma_descr has the same layout as ++ USB_IN_Desc for the relevant fields.) */ ++ prepare_rx_descriptor((struct etrax_dma_descr*)&RxDescList[i]); ++ ++ } ++ /* Special handling of last descriptor */ ++ RxDescList[i].sw_len = RX_DESC_BUF_SIZE; ++ RxDescList[i].command = IO_STATE(USB_IN_command, eol, yes); ++ RxDescList[i].next = virt_to_phys(&RxDescList[0]); ++ RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); ++ RxDescList[i].hw_len = 0; ++ RxDescList[i].status = 0; ++ ++ /* Setup list pointers that show progress in list */ ++ myNextRxDesc = &RxDescList[0]; ++ myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; ++ ++ flush_etrax_cache(); ++ /* Point DMA to first descriptor in list and start it */ ++ *R_DMA_CH9_FIRST = virt_to_phys(myNextRxDesc); ++ *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, start); ++} ++ ++ ++static void tc_dma_init_tx_bulk_list(void) { ++ int i; ++ volatile struct USB_EP_Desc *epDescr; ++ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ epDescr = &(TxBulkEPList[i]); ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxBulkEPList[i + 1]); ++ ++ /* Initiate two EPs, disabled and with the eol flag set. No need for any ++ preserved epid. */ ++ ++ /* The first one has the intr flag set so we get an interrupt when the DMA ++ channel is about to become disabled. */ ++ CHECK_ALIGN(&TxBulkDummyEPList[i][0]); ++ TxBulkDummyEPList[i][0].hw_len = 0; ++ TxBulkDummyEPList[i][0].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_STATE(USB_EP_command, intr, yes)); ++ TxBulkDummyEPList[i][0].sub = 0; ++ TxBulkDummyEPList[i][0].next = virt_to_phys(&TxBulkDummyEPList[i][1]); ++ ++ /* The second one. */ ++ CHECK_ALIGN(&TxBulkDummyEPList[i][1]); ++ TxBulkDummyEPList[i][1].hw_len = 0; ++ TxBulkDummyEPList[i][1].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | ++ IO_STATE(USB_EP_command, eol, yes)); ++ TxBulkDummyEPList[i][1].sub = 0; ++ /* The last dummy's next pointer is the same as the current EP's next pointer. */ ++ TxBulkDummyEPList[i][1].next = virt_to_phys(&TxBulkEPList[i + 1]); ++ } ++ ++ /* Special handling of last descr in list, make list circular */ ++ epDescr = &TxBulkEPList[i]; ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxBulkEPList[0]); ++ ++ /* Init DMA sub-channel pointers to last item in each list */ ++ *R_DMA_CH8_SUB0_EP = virt_to_phys(&TxBulkEPList[i]); ++ /* No point in starting the bulk channel yet. ++ *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */ ++} ++ ++static void tc_dma_init_tx_ctrl_list(void) { ++ int i; ++ volatile struct USB_EP_Desc *epDescr; ++ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ epDescr = &(TxCtrlEPList[i]); ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxCtrlEPList[i + 1]); ++ } ++ /* Special handling of last descr in list, make list circular */ ++ epDescr = &TxCtrlEPList[i]; ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxCtrlEPList[0]); ++ ++ /* Init DMA sub-channel pointers to last item in each list */ ++ *R_DMA_CH8_SUB1_EP = virt_to_phys(&TxCtrlEPList[i]); ++ /* No point in starting the ctrl channel yet. ++ *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */ ++} ++ ++ ++static void tc_dma_init_tx_intr_list(void) { ++ int i; ++ ++ TxIntrSB_zout.sw_len = 1; ++ TxIntrSB_zout.next = 0; ++ TxIntrSB_zout.buf = virt_to_phys(&zout_buffer[0]); ++ TxIntrSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | ++ IO_STATE(USB_SB_command, tt, zout) | ++ IO_STATE(USB_SB_command, full, yes) | ++ IO_STATE(USB_SB_command, eot, yes) | ++ IO_STATE(USB_SB_command, eol, yes)); ++ ++ for (i = 0; i < (MAX_INTR_INTERVAL - 1); i++) { ++ CHECK_ALIGN(&TxIntrEPList[i]); ++ TxIntrEPList[i].hw_len = 0; ++ TxIntrEPList[i].command = ++ (IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, enable, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); ++ TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[i + 1]); ++ } ++ ++ /* Special handling of last descr in list, make list circular */ ++ CHECK_ALIGN(&TxIntrEPList[i]); ++ TxIntrEPList[i].hw_len = 0; ++ TxIntrEPList[i].command = ++ (IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_STATE(USB_EP_command, enable, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); ++ TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[0]); ++ ++ intr_dbg("Initiated Intr EP descriptor list\n"); ++ ++ ++ /* Connect DMA 8 sub-channel 2 to first in list */ ++ *R_DMA_CH8_SUB2_EP = virt_to_phys(&TxIntrEPList[0]); ++} ++ ++static void tc_dma_init_tx_isoc_list(void) { ++ int i; ++ ++ DBFENTER; ++ ++ /* Read comment at zout_buffer declaration for an explanation to this. */ ++ TxIsocSB_zout.sw_len = 1; ++ TxIsocSB_zout.next = 0; ++ TxIsocSB_zout.buf = virt_to_phys(&zout_buffer[0]); ++ TxIsocSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | ++ IO_STATE(USB_SB_command, tt, zout) | ++ IO_STATE(USB_SB_command, full, yes) | ++ IO_STATE(USB_SB_command, eot, yes) | ++ IO_STATE(USB_SB_command, eol, yes)); ++ ++ /* The last isochronous EP descriptor is a dummy. */ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ CHECK_ALIGN(&TxIsocEPList[i]); ++ TxIsocEPList[i].hw_len = 0; ++ TxIsocEPList[i].command = IO_FIELD(USB_EP_command, epid, i); ++ TxIsocEPList[i].sub = 0; ++ TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[i + 1]); ++ } ++ ++ CHECK_ALIGN(&TxIsocEPList[i]); ++ TxIsocEPList[i].hw_len = 0; ++ ++ /* Must enable the last EP descr to get eof interrupt. */ ++ TxIsocEPList[i].command = (IO_STATE(USB_EP_command, enable, yes) | ++ IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIsocEPList[i].sub = virt_to_phys(&TxIsocSB_zout); ++ TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[0]); ++ ++ *R_DMA_CH8_SUB3_EP = virt_to_phys(&TxIsocEPList[0]); ++ *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); ++} ++ ++static int tc_dma_init(struct usb_hcd *hcd) { ++ tc_dma_init_rx_list(); ++ tc_dma_init_tx_bulk_list(); ++ tc_dma_init_tx_ctrl_list(); ++ tc_dma_init_tx_intr_list(); ++ tc_dma_init_tx_isoc_list(); ++ ++ if (cris_request_dma(USB_TX_DMA_NBR, ++ "ETRAX 100LX built-in USB (Tx)", ++ DMA_VERBOSE_ON_ERROR, ++ dma_usb)) { ++ err("Could not allocate DMA ch 8 for USB"); ++ return -EBUSY; ++ } ++ ++ if (cris_request_dma(USB_RX_DMA_NBR, ++ "ETRAX 100LX built-in USB (Rx)", ++ DMA_VERBOSE_ON_ERROR, ++ dma_usb)) { ++ err("Could not allocate DMA ch 9 for USB"); ++ return -EBUSY; ++ } ++ ++ *R_IRQ_MASK2_SET = ++ /* Note that these interrupts are not used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub0_descr, set) | ++ /* Sub channel 1 (ctrl) descr. interrupts are used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub1_descr, set) | ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub2_descr, set) | ++ /* Sub channel 3 (isoc) descr. interrupts are used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub3_descr, set); ++ ++ /* Note that the dma9_descr interrupt is not used. */ ++ *R_IRQ_MASK2_SET = ++ IO_STATE(R_IRQ_MASK2_SET, dma9_eop, set) | ++ IO_STATE(R_IRQ_MASK2_SET, dma9_descr, set); ++ ++ if (request_irq(ETRAX_USB_RX_IRQ, tc_dma_rx_interrupt, 0, ++ "ETRAX 100LX built-in USB (Rx)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_RX_IRQ); ++ return -EBUSY; ++ } ++ ++ if (request_irq(ETRAX_USB_TX_IRQ, tc_dma_tx_interrupt, 0, ++ "ETRAX 100LX built-in USB (Tx)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_TX_IRQ); ++ return -EBUSY; ++ } ++ ++ return 0; ++} ++ ++static void tc_dma_destroy(void) { ++ free_irq(ETRAX_USB_RX_IRQ, NULL); ++ free_irq(ETRAX_USB_TX_IRQ, NULL); ++ ++ cris_free_dma(USB_TX_DMA_NBR, "ETRAX 100LX built-in USB (Tx)"); ++ cris_free_dma(USB_RX_DMA_NBR, "ETRAX 100LX built-in USB (Rx)"); ++ ++} ++ ++static void tc_dma_link_intr_urb(struct urb *urb); ++ ++/* Handle processing of Bulk, Ctrl and Intr queues */ ++static void tc_dma_process_queue(int epid) { ++ struct urb *urb; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ unsigned long flags; ++ char toggle; ++ ++ if(epid_state[epid].disabled) { ++ /* Don't process any URBs on a disabled endpoint */ ++ return; ++ } ++ ++ /* Do not disturb us while fiddling with EPs and epids */ ++ local_irq_save(flags); ++ ++ /* For bulk, Ctrl and Intr can we only have one URB active at a time for ++ a specific EP. */ ++ if(activeUrbList[epid] != NULL) { ++ /* An URB is already active on EP, skip checking queue */ ++ local_irq_restore(flags); ++ return; ++ } ++ ++ urb = urb_list_first(epid); ++ if(urb == NULL) { ++ /* No URB waiting in EP queue. Nothing do to */ ++ local_irq_restore(flags); ++ return; ++ } ++ ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv != NULL); ++ ASSERT(urb_priv->urb_state == NOT_STARTED); ++ ASSERT(!usb_pipeisoc(urb->pipe)); ++ ++ /* Remove this URB from the queue and move it to active */ ++ activeUrbList[epid] = urb; ++ urb_list_del(urb, epid); ++ ++ urb_priv->urb_state = STARTED; ++ ++ /* Reset error counters (regardless of which direction this traffic is). */ ++ etrax_epid_clear_error(epid); ++ ++ /* Special handling of Intr EP lists */ ++ if(usb_pipeint(urb->pipe)) { ++ tc_dma_link_intr_urb(urb); ++ local_irq_restore(flags); ++ return; ++ } ++ ++ /* Software must preset the toggle bits for Bulk and Ctrl */ ++ if(usb_pipecontrol(urb->pipe)) { ++ /* Toggle bits are initialized only during setup transaction in a ++ CTRL transfer */ ++ etrax_epid_set_toggle(epid, 0, 0); ++ etrax_epid_set_toggle(epid, 1, 0); ++ } else { ++ toggle = usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), ++ usb_pipeout(urb->pipe)); ++ etrax_epid_set_toggle(epid, usb_pipeout(urb->pipe), toggle); ++ } ++ ++ tc_dbg("Added SBs from (URB:0x%x %s %s) to epid %d: %s\n", ++ (unsigned int)urb, str_dir(urb->pipe), str_type(urb->pipe), epid, ++ sblist_to_str(urb_priv->first_sb)); ++ ++ /* We start the DMA sub channel without checking if it's running or not, ++ because: ++ 1) If it's already running, issuing the start command is a nop. ++ 2) We avoid a test-and-set race condition. */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Assert that the EP descriptor is disabled. */ ++ ASSERT(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable))); ++ ++ /* Set up and enable the EP descriptor. */ ++ TxBulkEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ TxBulkEPList[epid].hw_len = 0; ++ TxBulkEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ /* Check if the dummy list is already with us (if several urbs were queued). */ ++ if (usb_pipein(urb->pipe) && (TxBulkEPList[epid].next != virt_to_phys(&TxBulkDummyEPList[epid][0]))) { ++ tc_dbg("Inviting dummy list to the party for urb 0x%lx, epid %d", ++ (unsigned long)urb, epid); ++ ++ /* We don't need to check if the DMA is at this EP or not before changing the ++ next pointer, since we will do it in one 32-bit write (EP descriptors are ++ 32-bit aligned). */ ++ TxBulkEPList[epid].next = virt_to_phys(&TxBulkDummyEPList[epid][0]); ++ } ++ ++ restart_dma8_sub0(); ++ ++ /* Update/restart the bulk start timer since we just started the channel.*/ ++ mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); ++ /* Update/restart the bulk eot timer since we just inserted traffic. */ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ break; ++ case PIPE_CONTROL: ++ /* Assert that the EP descriptor is disabled. */ ++ ASSERT(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable))); ++ ++ /* Set up and enable the EP descriptor. */ ++ TxCtrlEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ TxCtrlEPList[epid].hw_len = 0; ++ TxCtrlEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start); ++ break; ++ } ++ local_irq_restore(flags); ++} ++ ++static void tc_dma_link_intr_urb(struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ volatile struct USB_EP_Desc *tmp_ep; ++ struct USB_EP_Desc *ep_desc; ++ int i = 0, epid; ++ int pool_idx = 0; ++ ++ ASSERT(urb_priv != NULL); ++ epid = urb_priv->epid; ++ ASSERT(urb_priv->interval > 0); ++ ASSERT(urb_priv->intr_ep_pool_length > 0); ++ ++ tmp_ep = &TxIntrEPList[0]; ++ ++ /* Only insert one EP descriptor in list for Out Intr URBs. ++ We can only handle Out Intr with interval of 128ms because ++ it's not possible to insert several Out Intr EPs because they ++ are not consumed by the DMA. */ ++ if(usb_pipeout(urb->pipe)) { ++ ep_desc = urb_priv->intr_ep_pool[0]; ++ ASSERT(ep_desc); ++ ep_desc->next = tmp_ep->next; ++ tmp_ep->next = virt_to_phys(ep_desc); ++ i++; ++ } else { ++ /* Loop through Intr EP descriptor list and insert EP for URB at ++ specified interval */ ++ do { ++ /* Each EP descriptor with eof flag sat signals a new frame */ ++ if (tmp_ep->command & IO_MASK(USB_EP_command, eof)) { ++ /* Insert a EP from URBs EP pool at correct interval */ ++ if ((i % urb_priv->interval) == 0) { ++ ep_desc = urb_priv->intr_ep_pool[pool_idx]; ++ ASSERT(ep_desc); ++ ep_desc->next = tmp_ep->next; ++ tmp_ep->next = virt_to_phys(ep_desc); ++ pool_idx++; ++ ASSERT(pool_idx <= urb_priv->intr_ep_pool_length); + } ++ i++; ++ } ++ tmp_ep = (struct USB_EP_Desc *)phys_to_virt(tmp_ep->next); ++ } while(tmp_ep != &TxIntrEPList[0]); ++ } ++ ++ intr_dbg("Added SBs to intr epid %d: %s interval:%d (%d EP)\n", epid, ++ sblist_to_str(urb_priv->first_sb), urb_priv->interval, pool_idx); ++ ++ /* We start the DMA sub channel without checking if it's running or not, ++ because: ++ 1) If it's already running, issuing the start command is a nop. ++ 2) We avoid a test-and-set race condition. */ ++ *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start); ++} ++ ++static void tc_dma_process_isoc_urb(struct urb *urb) { ++ unsigned long flags; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid; ++ ++ /* Do not disturb us while fiddling with EPs and epids */ ++ local_irq_save(flags); ++ ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->first_sb); ++ epid = urb_priv->epid; ++ ++ if(activeUrbList[epid] == NULL) { ++ /* EP is idle, so make this URB active */ ++ activeUrbList[epid] = urb; ++ urb_list_del(urb, epid); ++ ASSERT(TxIsocEPList[epid].sub == 0); ++ ASSERT(!(TxIsocEPList[epid].command & ++ IO_STATE(USB_EP_command, enable, yes))); ++ ++ /* Differentiate between In and Out Isoc. Because In SBs are not consumed*/ ++ if(usb_pipein(urb->pipe)) { ++ /* Each EP for In Isoc will have only one SB descriptor, setup when ++ submitting the first active urb. We do it here by copying from URBs ++ pre-allocated SB. */ ++ memcpy((void *)&(TxIsocSBList[epid]), urb_priv->first_sb, ++ sizeof(TxIsocSBList[epid])); ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(&(TxIsocSBList[epid])); ++ } else { ++ /* For Out Isoc we attach the pre-allocated list of SBs for the URB */ ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ ++ isoc_dbg("Attached first URB:0x%x[%d] to epid:%d first_sb:0x%x" ++ " last_sb::0x%x\n", ++ (unsigned int)urb, urb_priv->urb_num, epid, ++ (unsigned int)(urb_priv->first_sb), ++ (unsigned int)(urb_priv->last_sb)); ++ } ++ ++ if (urb->transfer_flags & URB_ISO_ASAP) { ++ /* The isoc transfer should be started as soon as possible. The ++ start_frame field is a return value if URB_ISO_ASAP was set. Comparing ++ R_USB_FM_NUMBER with a USB Chief trace shows that the first isoc IN ++ token is sent 2 frames later. I'm not sure how this affects usage of ++ the start_frame field by the device driver, or how it affects things ++ when USB_ISO_ASAP is not set, so therefore there's no compensation for ++ the 2 frame "lag" here. */ ++ urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff); ++ TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ urb_priv->urb_state = STARTED; ++ isoc_dbg("URB_ISO_ASAP set, urb->start_frame set to %d\n", ++ urb->start_frame); ++ } else { ++ /* Not started yet. */ ++ urb_priv->urb_state = NOT_STARTED; ++ isoc_warn("urb_priv->urb_state set to NOT_STARTED for URB:0x%x\n", ++ (unsigned int)urb); ++ } ++ ++ } else { ++ /* An URB is already active on the EP. Leave URB in queue and let ++ finish_isoc_urb process it after current active URB */ ++ ASSERT(TxIsocEPList[epid].sub != 0); ++ ++ if(usb_pipein(urb->pipe)) { ++ /* Because there already is a active In URB on this epid we do nothing ++ and the finish_isoc_urb() function will handle switching to next URB*/ ++ ++ } else { /* For Out Isoc, insert new URBs traffic last in SB-list. */ ++ struct USB_SB_Desc *temp_sb_desc; ++ ++ /* Set state STARTED to all Out Isoc URBs added to SB list because we ++ don't know how many of them that are finished before descr interrupt*/ ++ urb_priv->urb_state = STARTED; ++ ++ /* Find end of current SB list by looking for SB with eol flag sat */ ++ temp_sb_desc = phys_to_virt(TxIsocEPList[epid].sub); ++ while ((temp_sb_desc->command & IO_MASK(USB_SB_command, eol)) != ++ IO_STATE(USB_SB_command, eol, yes)) { ++ ASSERT(temp_sb_desc->next); ++ temp_sb_desc = phys_to_virt(temp_sb_desc->next); ++ } ++ ++ isoc_dbg("Appended URB:0x%x[%d] (first:0x%x last:0x%x) to epid:%d" ++ " sub:0x%x eol:0x%x\n", ++ (unsigned int)urb, urb_priv->urb_num, ++ (unsigned int)(urb_priv->first_sb), ++ (unsigned int)(urb_priv->last_sb), epid, ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)temp_sb_desc); ++ ++ /* Next pointer must be set before eol is removed. */ ++ temp_sb_desc->next = virt_to_phys(urb_priv->first_sb); ++ /* Clear the previous end of list flag since there is a new in the ++ added SB descriptor list. */ ++ temp_sb_desc->command &= ~IO_MASK(USB_SB_command, eol); ++ ++ if (!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { ++ __u32 epid_data; ++ /* 8.8.5 in Designer's Reference says we should check for and correct ++ any errors in the EP here. That should not be necessary if ++ epid_attn is handled correctly, so we assume all is ok. */ ++ epid_data = etrax_epid_iso_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) != ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ isoc_err("Disabled Isoc EP with error:%d on epid:%d when appending" ++ " URB:0x%x[%d]\n", ++ IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data), epid, ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ ++ /* The SB list was exhausted. */ ++ if (virt_to_phys(urb_priv->last_sb) != TxIsocEPList[epid].sub) { ++ /* The new sublist did not get processed before the EP was ++ disabled. Setup the EP again. */ ++ ++ if(virt_to_phys(temp_sb_desc) == TxIsocEPList[epid].sub) { ++ isoc_dbg("EP for epid:%d stoped at SB:0x%x before newly inserted" ++ ", restarting from this URBs SB:0x%x\n", ++ epid, (unsigned int)temp_sb_desc, ++ (unsigned int)(urb_priv->first_sb)); ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff); ++ /* Enable the EP again so data gets processed this time */ ++ TxIsocEPList[epid].command |= ++ IO_STATE(USB_EP_command, enable, yes); ++ ++ } else { ++ /* The EP has been disabled but not at end this URB (god knows ++ where). This should generate an epid_attn so we should not be ++ here */ ++ isoc_warn("EP was disabled on sb:0x%x before SB list for" ++ " URB:0x%x[%d] got processed\n", ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ } else { ++ /* This might happend if we are slow on this function and isn't ++ an error. */ ++ isoc_dbg("EP was disabled and finished with SBs from appended" ++ " URB:0x%x[%d]\n", (unsigned int)urb, urb_priv->urb_num); ++ } ++ } ++ } ++ } ++ ++ /* Start the DMA sub channel */ ++ *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); ++ ++ local_irq_restore(flags); ++} ++ ++static void tc_dma_unlink_intr_urb(struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */ ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ volatile struct USB_EP_Desc *unlink_ep; /* The one we should remove from ++ the list. */ ++ int count = 0; ++ volatile int timeout = 10000; ++ int epid; ++ ++ /* Read 8.8.4 in Designer's Reference, "Removing an EP Descriptor from the ++ List". */ ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->intr_ep_pool_length > 0); ++ epid = urb_priv->epid; ++ ++ /* First disable all Intr EPs belonging to epid for this URB */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* Disable EP */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ ++ /* Now unlink all EPs belonging to this epid from Descr list */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* This is the one we should unlink. */ ++ unlink_ep = next_ep; ++ ++ /* Actually unlink the EP from the DMA list. */ ++ curr_ep->next = unlink_ep->next; ++ ++ /* Wait until the DMA is no longer at this descriptor. */ ++ while((*R_DMA_CH8_SUB2_EP == virt_to_phys(unlink_ep)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Intr to leave unlink EP\n"); ++ } ++ ++ count++; ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ if(count != urb_priv->intr_ep_pool_length) { ++ intr_warn("Unlinked %d of %d Intr EPs for URB:0x%x[%d]\n", count, ++ urb_priv->intr_ep_pool_length, (unsigned int)urb, ++ urb_priv->urb_num); ++ } else { ++ intr_dbg("Unlinked %d of %d interrupt EPs for URB:0x%x\n", count, ++ urb_priv->intr_ep_pool_length, (unsigned int)urb); ++ } ++} ++ ++static void check_finished_bulk_tx_epids(struct usb_hcd *hcd, ++ int timer) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ __u32 epid_data; ++ ++ /* Protect TxEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ /* A finished EP descriptor is disabled and has a valid sub pointer */ ++ if (!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) && ++ (TxBulkEPList[epid].sub != 0)) { ++ ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ /* Sanity checks */ ++ ASSERT(urb); ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Only handle finished out Bulk EPs here, ++ and let RX interrupt take care of the rest */ ++ if(!epid_out_traffic(epid)) { ++ continue; ++ } ++ ++ if(timer) { ++ tc_warn("Found finished %s Bulk epid:%d URB:0x%x[%d] from timeout\n", ++ epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb, ++ urb_priv->urb_num); ++ } else { ++ tc_dbg("Found finished %s Bulk epid:%d URB:0x%x[%d] from interrupt\n", ++ epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb, ++ urb_priv->urb_num); ++ } ++ ++ if(urb_priv->urb_state == UNLINK) { ++ /* This Bulk URB is requested to be unlinked, that means that the EP ++ has been disabled and we might not have sent all data */ ++ tc_finish_urb(hcd, urb, urb->status); ++ continue; ++ } ++ ++ ASSERT(urb_priv->urb_state == STARTED); ++ if (phys_to_virt(TxBulkEPList[epid].sub) != urb_priv->last_sb) { ++ tc_err("Endpoint got disabled before reaching last sb\n"); ++ } ++ ++ epid_data = etrax_epid_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) == ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ /* This means that the endpoint has no error, is disabled ++ and had inserted traffic, i.e. transfer successfully completed. */ ++ tc_finish_urb(hcd, urb, 0); ++ } else { ++ /* Shouldn't happen. We expect errors to be caught by epid ++ attention. */ ++ tc_err("Found disabled bulk EP desc (epid:%d error:%d)\n", ++ epid, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data)); ++ } ++ } else { ++ tc_dbg("Ignoring In Bulk epid:%d, let RX interrupt handle it\n", epid); ++ } ++ } ++ ++ local_irq_restore(flags); ++} ++ ++static void check_finished_ctrl_tx_epids(struct usb_hcd *hcd) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ __u32 epid_data; ++ ++ /* Protect TxEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if(epid == DUMMY_EPID) ++ continue; ++ ++ /* A finished EP descriptor is disabled and has a valid sub pointer */ ++ if (!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) && ++ (TxCtrlEPList[epid].sub != 0)) { ++ ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ ++ if(urb == NULL) { ++ tc_warn("Found finished Ctrl epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ /* Sanity checks */ ++ ASSERT(usb_pipein(urb->pipe)); ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ if (phys_to_virt(TxCtrlEPList[epid].sub) != urb_priv->last_sb) { ++ tc_err("Endpoint got disabled before reaching last sb\n"); ++ } ++ ++ epid_data = etrax_epid_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) == ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ /* This means that the endpoint has no error, is disabled ++ and had inserted traffic, i.e. transfer successfully completed. */ ++ ++ /* Check if RX-interrupt for In Ctrl has been processed before ++ finishing the URB */ ++ if(urb_priv->ctrl_rx_done) { ++ tc_dbg("Finishing In Ctrl URB:0x%x[%d] in tx_interrupt\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ tc_finish_urb(hcd, urb, 0); ++ } else { ++ /* If we get zout descriptor interrupt before RX was done for a ++ In Ctrl transfer, then we flag that and it will be finished ++ in the RX-Interrupt */ ++ urb_priv->ctrl_zout_done = 1; ++ tc_dbg("Got zout descr interrupt before RX interrupt\n"); ++ } ++ } else { ++ /* Shouldn't happen. We expect errors to be caught by epid ++ attention. */ ++ tc_err("Found disabled Ctrl EP desc (epid:%d URB:0x%x[%d]) error_code:%d\n", epid, (unsigned int)urb, urb_priv->urb_num, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data)); ++ __dump_ep_desc(&(TxCtrlEPList[epid])); ++ __dump_ept_data(epid); ++ } ++ } ++ } ++ local_irq_restore(flags); ++} ++ ++/* This function goes through all epids that are setup for Out Isoc transfers ++ and marks (isoc_out_done) all queued URBs that the DMA has finished ++ transfer for. ++ No URB completetion is done here to make interrupt routine return quickly. ++ URBs are completed later with help of complete_isoc_bottom_half() that ++ becomes schedules when this functions is finished. */ ++static void check_finished_isoc_tx_epids(void) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ struct USB_SB_Desc* sb_desc; ++ int epid_done; ++ ++ /* Protect TxIsocEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (TxIsocEPList[epid].sub == 0 || epid == INVALID_EPID || ++ !epid_out_traffic(epid)) { ++ /* Nothing here to see. */ ++ continue; ++ } ++ ASSERT(epid_inuse(epid)); ++ ASSERT(epid_isoc(epid)); ++ ++ sb_desc = phys_to_virt(TxIsocEPList[epid].sub); ++ /* Find the last descriptor of the currently active URB for this ep. ++ This is the first descriptor in the sub list marked for a descriptor ++ interrupt. */ ++ while (sb_desc && !IO_EXTRACT(USB_SB_command, intr, sb_desc->command)) { ++ sb_desc = sb_desc->next ? phys_to_virt(sb_desc->next) : 0; ++ } ++ ASSERT(sb_desc); ++ ++ isoc_dbg("Descr IRQ checking epid:%d sub:0x%x intr:0x%x\n", ++ epid, (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)sb_desc); ++ ++ urb = activeUrbList[epid]; ++ if(urb == NULL) { ++ isoc_err("Isoc Descr irq on epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ epid_done = 0; ++ while(urb && !epid_done) { ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->urb_state == STARTED || ++ urb_priv->urb_state == UNLINK); ++ ++ if (sb_desc != urb_priv->last_sb) { ++ /* This urb has been sent. */ ++ urb_priv->isoc_out_done = 1; ++ ++ } else { /* Found URB that has last_sb as the interrupt reason */ ++ ++ /* Check if EP has been disabled, meaning that all transfers are done*/ ++ if(!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { ++ ASSERT((sb_desc->command & IO_MASK(USB_SB_command, eol)) == ++ IO_STATE(USB_SB_command, eol, yes)); ++ ASSERT(sb_desc->next == 0); ++ urb_priv->isoc_out_done = 1; ++ } else { ++ isoc_dbg("Skipping URB:0x%x[%d] because EP not disabled yet\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ /* Stop looking any further in queue */ ++ epid_done = 1; ++ } ++ ++ if (!epid_done) { ++ if(urb == activeUrbList[epid]) { ++ urb = urb_list_first(epid); ++ } else { ++ urb = urb_list_next(urb, epid); ++ } ++ } ++ } /* END: while(urb && !epid_done) */ ++ } ++ ++ local_irq_restore(flags); ++} ++ ++ ++/* This is where the Out Isoc URBs are realy completed. This function is ++ scheduled from tc_dma_tx_interrupt() when one or more Out Isoc transfers ++ are done. This functions completes all URBs earlier marked with ++ isoc_out_done by fast interrupt routine check_finished_isoc_tx_epids() */ ++ ++static void complete_isoc_bottom_half(void *data) { ++ struct crisv10_isoc_complete_data *comp_data; ++ struct usb_iso_packet_descriptor *packet; ++ struct crisv10_urb_priv * urb_priv; ++ unsigned long flags; ++ struct urb* urb; ++ int epid_done; ++ int epid; ++ int i; ++ ++ comp_data = (struct crisv10_isoc_complete_data*)data; ++ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { ++ if(!epid_inuse(epid) || !epid_isoc(epid) || !epid_out_traffic(epid) || epid == DUMMY_EPID) { ++ /* Only check valid Out Isoc epids */ ++ continue; ++ } ++ ++ isoc_dbg("Isoc bottom-half checking epid:%d, sub:0x%x\n", epid, ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub)); ++ ++ /* The descriptor interrupt handler has marked all transmitted Out Isoc ++ URBs with isoc_out_done. Now we traverse all epids and for all that ++ have out Isoc traffic we traverse its URB list and complete the ++ transmitted URBs. */ ++ epid_done = 0; ++ while (!epid_done) { ++ ++ /* Get the active urb (if any) */ ++ urb = activeUrbList[epid]; ++ if (urb == 0) { ++ isoc_dbg("No active URB on epid:%d anymore\n", epid); ++ epid_done = 1; ++ continue; ++ } ++ ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ if (!(urb_priv->isoc_out_done)) { ++ /* We have reached URB that isn't flaged done yet, stop traversing. */ ++ isoc_dbg("Stoped traversing Out Isoc URBs on epid:%d" ++ " before not yet flaged URB:0x%x[%d]\n", ++ epid, (unsigned int)urb, urb_priv->urb_num); ++ epid_done = 1; ++ continue; ++ } ++ ++ /* This urb has been sent. */ ++ isoc_dbg("Found URB:0x%x[%d] that is flaged isoc_out_done\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ ++ /* Set ok on transfered packets for this URB and finish it */ ++ for (i = 0; i < urb->number_of_packets; i++) { ++ packet = &urb->iso_frame_desc[i]; ++ packet->status = 0; ++ packet->actual_length = packet->length; ++ } ++ urb_priv->isoc_packet_counter = urb->number_of_packets; ++ tc_finish_urb(comp_data->hcd, urb, 0); ++ ++ } /* END: while(!epid_done) */ ++ } /* END: for(epid...) */ ++ ++ local_irq_restore(flags); ++ kmem_cache_free(isoc_compl_cache, comp_data); ++} ++ ++ ++static void check_finished_intr_tx_epids(struct usb_hcd *hcd) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ ++ /* Protect TxintrEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if(!epid_inuse(epid) || !epid_intr(epid) || !epid_out_traffic(epid)) { ++ /* Nothing to see on this epid. Only check valid Out Intr epids */ ++ continue; ++ } ++ ++ urb = activeUrbList[epid]; ++ if(urb == 0) { ++ intr_warn("Found Out Intr epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_INTERRUPT); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Go through EPs between first and second sof-EP. It's here Out Intr EPs ++ are inserted.*/ ++ curr_ep = &TxIntrEPList[0]; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if(next_ep == urb_priv->intr_ep_pool[0]) { ++ /* We found the Out Intr EP for this epid */ ++ ++ /* Disable it so it doesn't get processed again */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ ++ /* Finish the active Out Intr URB with status OK */ ++ tc_finish_urb(hcd, urb, 0); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != &TxIntrEPList[1]); ++ ++ } ++ local_irq_restore(flags); ++} ++ ++/* Interrupt handler for DMA8/IRQ24 with subchannels (called from hardware intr) */ ++static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc) { ++ struct usb_hcd *hcd = (struct usb_hcd*)vhc; ++ ASSERT(hcd); ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub0_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB0_CLR_INTR = IO_STATE(R_DMA_CH8_SUB0_CLR_INTR, clr_descr, do); ++ restart_dma8_sub0(); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub1_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB1_CLR_INTR = IO_STATE(R_DMA_CH8_SUB1_CLR_INTR, clr_descr, do); ++ check_finished_ctrl_tx_epids(hcd); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub2_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB2_CLR_INTR = IO_STATE(R_DMA_CH8_SUB2_CLR_INTR, clr_descr, do); ++ check_finished_intr_tx_epids(hcd); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub3_descr)) { ++ struct crisv10_isoc_complete_data* comp_data; ++ ++ /* Flag done Out Isoc for later completion */ ++ check_finished_isoc_tx_epids(); ++ ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB3_CLR_INTR = IO_STATE(R_DMA_CH8_SUB3_CLR_INTR, clr_descr, do); ++ /* Schedule bottom half of Out Isoc completion function. This function ++ finishes the URBs marked with isoc_out_done */ ++ comp_data = (struct crisv10_isoc_complete_data*) ++ kmem_cache_alloc(isoc_compl_cache, SLAB_ATOMIC); ++ ASSERT(comp_data != NULL); ++ comp_data ->hcd = hcd; ++ ++ INIT_WORK(&comp_data->usb_bh, complete_isoc_bottom_half, comp_data); ++ schedule_work(&comp_data->usb_bh); ++ } ++ ++ return IRQ_HANDLED; ++} ++ ++/* Interrupt handler for DMA9/IRQ25 (called from hardware intr) */ ++static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc) { ++ unsigned long flags; ++ struct urb *urb; ++ struct usb_hcd *hcd = (struct usb_hcd*)vhc; ++ struct crisv10_urb_priv *urb_priv; ++ int epid = 0; ++ int real_error; ++ ++ ASSERT(hcd); ++ ++ /* Clear this interrupt. */ ++ *R_DMA_CH9_CLR_INTR = IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, do); ++ ++ /* Custom clear interrupt for this interrupt */ ++ /* The reason we cli here is that we call the driver's callback functions. */ ++ local_irq_save(flags); ++ ++ /* Note that this while loop assumes that all packets span only ++ one rx descriptor. */ ++ while(myNextRxDesc->status & IO_MASK(USB_IN_status, eop)) { ++ epid = IO_EXTRACT(USB_IN_status, epid, myNextRxDesc->status); ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ ++ ASSERT(epid_inuse(epid)); ++ if (!urb) { ++ dma_err("No urb for epid %d in rx interrupt\n", epid); ++ goto skip_out; ++ } ++ ++ /* Check if any errors on epid */ ++ real_error = 0; ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, error)) { ++ __u32 r_usb_ept_data; ++ ++ if (usb_pipeisoc(urb->pipe)) { ++ r_usb_ept_data = etrax_epid_iso_get(epid); ++ if((r_usb_ept_data & IO_MASK(R_USB_EPT_DATA_ISO, valid)) && ++ (IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data) == 0) && ++ (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata))) { ++ /* Not an error, just a failure to receive an expected iso ++ in packet in this frame. This is not documented ++ in the designers reference. Continue processing. ++ */ ++ } else real_error = 1; ++ } else real_error = 1; ++ } ++ ++ if(real_error) { ++ dma_err("Error in RX descr on epid:%d for URB 0x%x", ++ epid, (unsigned int)urb); ++ dump_ept_data(epid); ++ dump_in_desc(myNextRxDesc); ++ goto skip_out; ++ } ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->urb_state == STARTED || ++ urb_priv->urb_state == UNLINK); ++ ++ if ((usb_pipetype(urb->pipe) == PIPE_BULK) || ++ (usb_pipetype(urb->pipe) == PIPE_CONTROL) || ++ (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) { ++ ++ /* We get nodata for empty data transactions, and the rx descriptor's ++ hw_len field is not valid in that case. No data to copy in other ++ words. */ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { ++ /* No data to copy */ ++ } else { ++ /* ++ dma_dbg("Processing RX for URB:0x%x epid:%d (data:%d ofs:%d)\n", ++ (unsigned int)urb, epid, myNextRxDesc->hw_len, ++ urb_priv->rx_offset); ++ */ ++ /* Only copy data if URB isn't flaged to be unlinked*/ ++ if(urb_priv->urb_state != UNLINK) { ++ /* Make sure the data fits in the buffer. */ ++ if(urb_priv->rx_offset + myNextRxDesc->hw_len ++ <= urb->transfer_buffer_length) { ++ ++ /* Copy the data to URBs buffer */ ++ memcpy(urb->transfer_buffer + urb_priv->rx_offset, ++ phys_to_virt(myNextRxDesc->buf), myNextRxDesc->hw_len); ++ urb_priv->rx_offset += myNextRxDesc->hw_len; ++ } else { ++ /* Signal overflow when returning URB */ ++ urb->status = -EOVERFLOW; ++ tc_finish_urb_later(hcd, urb, urb->status); ++ } ++ } ++ } ++ ++ /* Check if it was the last packet in the transfer */ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, eot)) { ++ /* Special handling for In Ctrl URBs. */ ++ if(usb_pipecontrol(urb->pipe) && usb_pipein(urb->pipe) && ++ !(urb_priv->ctrl_zout_done)) { ++ /* Flag that RX part of Ctrl transfer is done. Because zout descr ++ interrupt hasn't happend yet will the URB be finished in the ++ TX-Interrupt. */ ++ urb_priv->ctrl_rx_done = 1; ++ tc_dbg("Not finishing In Ctrl URB:0x%x from rx_interrupt, waiting" ++ " for zout\n", (unsigned int)urb); ++ } else { ++ tc_finish_urb(hcd, urb, 0); ++ } ++ } ++ } else { /* ISOC RX */ ++ /* ++ isoc_dbg("Processing RX for epid:%d (URB:0x%x) ISOC pipe\n", ++ epid, (unsigned int)urb); ++ */ ++ ++ struct usb_iso_packet_descriptor *packet; ++ ++ if (urb_priv->urb_state == UNLINK) { ++ isoc_warn("Ignoring Isoc Rx data for urb being unlinked.\n"); ++ goto skip_out; ++ } else if (urb_priv->urb_state == NOT_STARTED) { ++ isoc_err("What? Got Rx data for Isoc urb that isn't started?\n"); ++ goto skip_out; ++ } ++ ++ packet = &urb->iso_frame_desc[urb_priv->isoc_packet_counter]; ++ ASSERT(packet); ++ packet->status = 0; ++ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { ++ /* We get nodata for empty data transactions, and the rx descriptor's ++ hw_len field is not valid in that case. We copy 0 bytes however to ++ stay in synch. */ ++ packet->actual_length = 0; ++ } else { ++ packet->actual_length = myNextRxDesc->hw_len; ++ /* Make sure the data fits in the buffer. */ ++ ASSERT(packet->actual_length <= packet->length); ++ memcpy(urb->transfer_buffer + packet->offset, ++ phys_to_virt(myNextRxDesc->buf), packet->actual_length); ++ if(packet->actual_length > 0) ++ isoc_dbg("Copied %d bytes, packet %d for URB:0x%x[%d]\n", ++ packet->actual_length, urb_priv->isoc_packet_counter, ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ ++ /* Increment the packet counter. */ ++ urb_priv->isoc_packet_counter++; ++ ++ /* Note that we don't care about the eot field in the rx descriptor's ++ status. It will always be set for isoc traffic. */ ++ if (urb->number_of_packets == urb_priv->isoc_packet_counter) { ++ /* Complete the urb with status OK. */ ++ tc_finish_urb(hcd, urb, 0); ++ } ++ } ++ ++ skip_out: ++ myNextRxDesc->status = 0; ++ myNextRxDesc->command |= IO_MASK(USB_IN_command, eol); ++ myLastRxDesc->command &= ~IO_MASK(USB_IN_command, eol); ++ myLastRxDesc = myNextRxDesc; ++ myNextRxDesc = phys_to_virt(myNextRxDesc->next); ++ flush_etrax_cache(); ++ *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, restart); ++ } ++ ++ local_irq_restore(flags); ++ ++ return IRQ_HANDLED; ++} ++ ++static void tc_bulk_start_timer_func(unsigned long dummy) { ++ /* We might enable an EP descriptor behind the current DMA position when ++ it's about to decide that there are no more bulk traffic and it should ++ stop the bulk channel. ++ Therefore we periodically check if the bulk channel is stopped and there ++ is an enabled bulk EP descriptor, in which case we start the bulk ++ channel. */ ++ ++ if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) { ++ int epid; ++ ++ timer_dbg("bulk_start_timer: Bulk DMA channel not running.\n"); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ timer_warn("Found enabled EP for epid %d, starting bulk channel.\n", ++ epid); ++ restart_dma8_sub0(); ++ ++ /* Restart the bulk eot timer since we just started the bulk channel.*/ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ ++ /* No need to search any further. */ ++ break; ++ } ++ } ++ } else { ++ timer_dbg("bulk_start_timer: Bulk DMA channel running.\n"); ++ } ++} ++ ++static void tc_bulk_eot_timer_func(unsigned long dummy) { ++ struct usb_hcd *hcd = (struct usb_hcd*)dummy; ++ ASSERT(hcd); ++ /* Because of a race condition in the top half, we might miss a bulk eot. ++ This timer "simulates" a bulk eot if we don't get one for a while, ++ hopefully correcting the situation. */ ++ timer_dbg("bulk_eot_timer timed out.\n"); ++ check_finished_bulk_tx_epids(hcd, 1); ++} ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Device driver block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* Forward declarations for device driver functions */ ++static int devdrv_hcd_probe(struct device *); ++static int devdrv_hcd_remove(struct device *); ++#ifdef CONFIG_PM ++static int devdrv_hcd_suspend(struct device *, u32, u32); ++static int devdrv_hcd_resume(struct device *, u32); ++#endif /* CONFIG_PM */ ++ ++/* the device */ ++static struct platform_device *devdrv_hc_platform_device; ++ ++/* device driver interface */ ++static struct device_driver devdrv_hc_device_driver = { ++ .name = (char *) hc_name, ++ .bus = &platform_bus_type, ++ ++ .probe = devdrv_hcd_probe, ++ .remove = devdrv_hcd_remove, ++ ++#ifdef CONFIG_PM ++ .suspend = devdrv_hcd_suspend, ++ .resume = devdrv_hcd_resume, ++#endif /* CONFIG_PM */ ++}; + +- CHECK_ALIGN(&TxIsocEPList[i]); +- TxIsocEPList[i].hw_len = 0; +- +- /* Must enable the last EP descr to get eof interrupt. */ +- TxIsocEPList[i].command = (IO_STATE(USB_EP_command, enable, yes) | +- IO_STATE(USB_EP_command, eof, yes) | +- IO_STATE(USB_EP_command, eol, yes) | +- IO_FIELD(USB_EP_command, epid, INVALID_EPID)); +- TxIsocEPList[i].sub = virt_to_phys(&TxIsocSB_zout); +- TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[0]); +- +- *R_DMA_CH8_SUB3_EP = virt_to_phys(&TxIsocEPList[0]); +- *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); +- +- DBFEXIT; +-} +- +-static void etrax_usb_unlink_intr_urb(struct urb *urb) ++/* initialize the host controller and driver */ ++static int __init_or_module devdrv_hcd_probe(struct device *dev) + { +- volatile USB_EP_Desc_t *first_ep; /* First EP in the list. */ +- volatile USB_EP_Desc_t *curr_ep; /* Current EP, the iterator. */ +- volatile USB_EP_Desc_t *next_ep; /* The EP after current. */ +- volatile USB_EP_Desc_t *unlink_ep; /* The one we should remove from the list. */ +- +- int epid; +- +- /* Read 8.8.4 in Designer's Reference, "Removing an EP Descriptor from the List". */ +- +- DBFENTER; +- +- epid = ((etrax_urb_priv_t *)urb->hcpriv)->epid; +- +- first_ep = &TxIntrEPList[0]; +- curr_ep = first_ep; +- +- +- /* Note that this loop removes all EP descriptors with this epid. This assumes +- that all EP descriptors belong to the one and only urb for this epid. */ +- +- do { +- next_ep = (USB_EP_Desc_t *)phys_to_virt(curr_ep->next); +- +- if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { +- +- dbg_intr("Found EP to unlink for epid %d", epid); +- +- /* This is the one we should unlink. */ +- unlink_ep = next_ep; +- +- /* Actually unlink the EP from the DMA list. */ +- curr_ep->next = unlink_ep->next; +- +- /* Wait until the DMA is no longer at this descriptor. */ +- while (*R_DMA_CH8_SUB2_EP == virt_to_phys(unlink_ep)); ++ struct usb_hcd *hcd; ++ struct crisv10_hcd *crisv10_hcd; ++ int retval; ++ ++ /* Check DMA burst length */ ++ if(IO_EXTRACT(R_BUS_CONFIG, dma_burst, *R_BUS_CONFIG) != ++ IO_STATE(R_BUS_CONFIG, dma_burst, burst32)) { ++ devdrv_err("Invalid DMA burst length in Etrax 100LX," ++ " needs to be 32\n"); ++ return -EPERM; ++ } ++ ++ hcd = usb_create_hcd(&crisv10_hc_driver, dev, dev->bus_id); ++ if (!hcd) ++ return -ENOMEM; ++ ++ crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ spin_lock_init(&crisv10_hcd->lock); ++ crisv10_hcd->num_ports = num_ports(); ++ crisv10_hcd->running = 0; ++ ++ dev_set_drvdata(dev, crisv10_hcd); ++ ++ devdrv_dbg("ETRAX USB IRQs HC:%d RX:%d TX:%d\n", ETRAX_USB_HC_IRQ, ++ ETRAX_USB_RX_IRQ, ETRAX_USB_TX_IRQ); ++ ++ /* Print out chip version read from registers */ ++ int rev_maj = *R_USB_REVISION & IO_MASK(R_USB_REVISION, major); ++ int rev_min = *R_USB_REVISION & IO_MASK(R_USB_REVISION, minor); ++ if(rev_min == 0) { ++ devdrv_info("Etrax 100LX USB Revision %d v1,2\n", rev_maj); ++ } else { ++ devdrv_info("Etrax 100LX USB Revision %d v%d\n", rev_maj, rev_min); ++ } ++ ++ devdrv_info("Bulk timer interval, start:%d eot:%d\n", ++ BULK_START_TIMER_INTERVAL, ++ BULK_EOT_TIMER_INTERVAL); ++ ++ ++ /* Init root hub data structures */ ++ if(rh_init()) { ++ devdrv_err("Failed init data for Root Hub\n"); ++ retval = -ENOMEM; ++ } ++ ++ if(port_in_use(0)) { ++ if (cris_request_io_interface(if_usb_1, "ETRAX100LX USB-HCD")) { ++ printk(KERN_CRIT "usb-host: request IO interface usb1 failed"); ++ retval = -EBUSY; ++ goto out; ++ } ++ devdrv_info("Claimed interface for USB physical port 1\n"); ++ } ++ if(port_in_use(1)) { ++ if (cris_request_io_interface(if_usb_2, "ETRAX100LX USB-HCD")) { ++ /* Free first interface if second failed to be claimed */ ++ if(port_in_use(0)) { ++ cris_free_io_interface(if_usb_1); ++ } ++ printk(KERN_CRIT "usb-host: request IO interface usb2 failed"); ++ retval = -EBUSY; ++ goto out; ++ } ++ devdrv_info("Claimed interface for USB physical port 2\n"); ++ } ++ ++ /* Init transfer controller structs and locks */ ++ if((retval = tc_init(hcd)) != 0) { ++ goto out; ++ } ++ ++ /* Attach interrupt functions for DMA and init DMA controller */ ++ if((retval = tc_dma_init(hcd)) != 0) { ++ goto out; ++ } ++ ++ /* Attach the top IRQ handler for USB controller interrupts */ ++ if (request_irq(ETRAX_USB_HC_IRQ, crisv10_hcd_top_irq, 0, ++ "ETRAX 100LX built-in USB (HC)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_HC_IRQ); ++ retval = -EBUSY; ++ goto out; ++ } ++ ++ /* iso_eof is only enabled when isoc traffic is running. */ ++ *R_USB_IRQ_MASK_SET = ++ /* IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set) | */ ++ IO_STATE(R_USB_IRQ_MASK_SET, bulk_eot, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, epid_attn, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, port_status, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set); ++ ++ ++ crisv10_ready_wait(); ++ /* Reset the USB interface. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, reset); ++ ++ /* Designer's Reference, p. 8 - 10 says we should Initate R_USB_FM_PSTART to ++ 0x2A30 (10800), to guarantee that control traffic gets 10% of the ++ bandwidth, and periodic transfer may allocate the rest (90%). ++ This doesn't work though. ++ The value 11960 is chosen to be just after the SOF token, with a couple ++ of bit times extra for possible bit stuffing. */ ++ *R_USB_FM_PSTART = IO_FIELD(R_USB_FM_PSTART, value, 11960); ++ ++ crisv10_ready_wait(); ++ /* Configure the USB interface as a host controller. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_config); ++ ++ ++ /* Check so controller not busy before enabling ports */ ++ crisv10_ready_wait(); ++ ++ /* Enable selected USB ports */ ++ if(port_in_use(0)) { ++ *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no); ++ } else { ++ *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes); ++ } ++ if(port_in_use(1)) { ++ *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no); ++ } else { ++ *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes); ++ } ++ ++ crisv10_ready_wait(); ++ /* Start processing of USB traffic. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ ++ /* Do not continue probing initialization before USB interface is done */ ++ crisv10_ready_wait(); ++ ++ /* Register our Host Controller to USB Core ++ * Finish the remaining parts of generic HCD initialization: allocate the ++ * buffers of consistent memory, register the bus ++ * and call the driver's reset() and start() routines. */ ++ retval = usb_add_hcd(hcd, ETRAX_USB_HC_IRQ, IRQF_DISABLED); ++ if (retval != 0) { ++ devdrv_err("Failed registering HCD driver\n"); ++ goto out; ++ } ++ ++ return 0; ++ ++ out: ++ devdrv_hcd_remove(dev); ++ return retval; ++} ++ ++ ++/* cleanup after the host controller and driver */ ++static int __init_or_module devdrv_hcd_remove(struct device *dev) ++{ ++ struct crisv10_hcd *crisv10_hcd = dev_get_drvdata(dev); ++ struct usb_hcd *hcd; ++ ++ if (!crisv10_hcd) ++ return 0; ++ hcd = crisv10_hcd_to_hcd(crisv10_hcd); ++ ++ ++ /* Stop USB Controller in Etrax 100LX */ ++ crisv10_hcd_reset(hcd); ++ ++ usb_remove_hcd(hcd); ++ devdrv_dbg("Removed HCD from USB Core\n"); ++ ++ /* Free USB Controller IRQ */ ++ free_irq(ETRAX_USB_HC_IRQ, NULL); ++ ++ /* Free resources */ ++ tc_dma_destroy(); ++ tc_destroy(); ++ ++ ++ if(port_in_use(0)) { ++ cris_free_io_interface(if_usb_1); ++ } ++ if(port_in_use(1)) { ++ cris_free_io_interface(if_usb_2); ++ } ++ ++ devdrv_dbg("Freed all claimed resources\n"); ++ ++ return 0; ++} ++ ++ ++#ifdef CONFIG_PM ++ ++static int devdrv_hcd_suspend(struct usb_hcd *hcd, u32 state, u32 level) ++{ ++ return 0; /* no-op for now */ ++} ++ ++static int devdrv_hcd_resume(struct usb_hcd *hcd, u32 level) ++{ ++ return 0; /* no-op for now */ ++} ++ ++#endif /* CONFIG_PM */ ++ ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Module block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* register driver */ ++static int __init module_hcd_init(void) ++{ ++ ++ if (usb_disabled()) ++ return -ENODEV; ++ ++ /* Here we select enabled ports by following defines created from ++ menuconfig */ ++#ifndef CONFIG_ETRAX_USB_HOST_PORT1 ++ ports &= ~(1<<0); ++#endif ++#ifndef CONFIG_ETRAX_USB_HOST_PORT2 ++ ports &= ~(1<<1); ++#endif + +- /* Now we are free to remove it and its SB descriptor. +- Note that it is assumed here that there is only one sb in the +- sb list for this ep. */ +- kmem_cache_free(usb_desc_cache, phys_to_virt(unlink_ep->sub)); +- kmem_cache_free(usb_desc_cache, (USB_EP_Desc_t *)unlink_ep); +- } ++ printk(KERN_INFO "%s version "VERSION" "COPYRIGHT"\n", product_desc); + +- curr_ep = phys_to_virt(curr_ep->next); ++ devdrv_hc_platform_device = ++ platform_device_register_simple((char *) hc_name, 0, NULL, 0); + +- } while (curr_ep != first_ep); +- urb->hcpriv = NULL; ++ if (IS_ERR(devdrv_hc_platform_device)) ++ return PTR_ERR(devdrv_hc_platform_device); ++ return driver_register(&devdrv_hc_device_driver); ++ /* ++ * Note that we do not set the DMA mask for the device, ++ * i.e. we pretend that we will use PIO, since no specific ++ * allocation routines are needed for DMA buffers. This will ++ * cause the HCD buffer allocation routines to fall back to ++ * kmalloc(). ++ */ + } + +-void etrax_usb_do_intr_recover(int epid) +-{ +- USB_EP_Desc_t *first_ep, *tmp_ep; ++/* unregister driver */ ++static void __exit module_hcd_exit(void) ++{ ++ driver_unregister(&devdrv_hc_device_driver); ++} + +- DBFENTER; +- +- first_ep = (USB_EP_Desc_t *)phys_to_virt(*R_DMA_CH8_SUB2_EP); +- tmp_ep = first_ep; +- +- /* What this does is simply to walk the list of interrupt +- ep descriptors and enable those that are disabled. */ +- +- do { +- if (IO_EXTRACT(USB_EP_command, epid, tmp_ep->command) == epid && +- !(tmp_ep->command & IO_MASK(USB_EP_command, enable))) { +- tmp_ep->command |= IO_STATE(USB_EP_command, enable, yes); +- } +- +- tmp_ep = (USB_EP_Desc_t *)phys_to_virt(tmp_ep->next); +- +- } while (tmp_ep != first_ep); +- +- +- DBFEXIT; +-} +- +-static int etrax_rh_unlink_urb (struct urb *urb) +-{ +- etrax_hc_t *hc; +- +- DBFENTER; +- +- hc = urb->dev->bus->hcpriv; +- +- if (hc->rh.urb == urb) { +- hc->rh.send = 0; +- del_timer(&hc->rh.rh_int_timer); +- } +- +- DBFEXIT; +- return 0; +-} +- +-static void etrax_rh_send_irq(struct urb *urb) +-{ +- __u16 data = 0; +- etrax_hc_t *hc = urb->dev->bus->hcpriv; +- DBFENTER; +- +-/* +- dbg_rh("R_USB_FM_NUMBER : 0x%08X", *R_USB_FM_NUMBER); +- dbg_rh("R_USB_FM_REMAINING: 0x%08X", *R_USB_FM_REMAINING); +-*/ +- +- data |= (hc->rh.wPortChange_1) ? (1 << 1) : 0; +- data |= (hc->rh.wPortChange_2) ? (1 << 2) : 0; +- +- *((__u16 *)urb->transfer_buffer) = cpu_to_le16(data); +- /* FIXME: Why is actual_length set to 1 when data is 2 bytes? +- Since only 1 byte is used, why not declare data as __u8? */ +- urb->actual_length = 1; +- urb->status = 0; +- +- if (hc->rh.send && urb->complete) { +- dbg_rh("wPortChange_1: 0x%04X", hc->rh.wPortChange_1); +- dbg_rh("wPortChange_2: 0x%04X", hc->rh.wPortChange_2); +- +- urb->complete(urb, NULL); +- } +- +- DBFEXIT; +-} +- +-static void etrax_rh_init_int_timer(struct urb *urb) +-{ +- etrax_hc_t *hc; +- +- DBFENTER; +- +- hc = urb->dev->bus->hcpriv; +- hc->rh.interval = urb->interval; +- init_timer(&hc->rh.rh_int_timer); +- hc->rh.rh_int_timer.function = etrax_rh_int_timer_do; +- hc->rh.rh_int_timer.data = (unsigned long)urb; +- /* FIXME: Is the jiffies resolution enough? All intervals < 10 ms will be mapped +- to 0, and the rest to the nearest lower 10 ms. */ +- hc->rh.rh_int_timer.expires = jiffies + ((HZ * hc->rh.interval) / 1000); +- add_timer(&hc->rh.rh_int_timer); +- +- DBFEXIT; +-} +- +-static void etrax_rh_int_timer_do(unsigned long ptr) +-{ +- struct urb *urb; +- etrax_hc_t *hc; +- +- DBFENTER; +- +- urb = (struct urb*)ptr; +- hc = urb->dev->bus->hcpriv; +- +- if (hc->rh.send) { +- etrax_rh_send_irq(urb); +- } +- +- DBFEXIT; +-} +- +-static int etrax_usb_setup_epid(struct urb *urb) +-{ +- int epid; +- char devnum, endpoint, out_traffic, slow; +- int maxlen; +- unsigned long flags; +- +- DBFENTER; +- +- epid = etrax_usb_lookup_epid(urb); +- if ((epid != -1)){ +- /* An epid that fits this urb has been found. */ +- DBFEXIT; +- return epid; +- } +- +- /* We must find and initiate a new epid for this urb. */ +- epid = etrax_usb_allocate_epid(); +- +- if (epid == -1) { +- /* Failed to allocate a new epid. */ +- DBFEXIT; +- return epid; +- } +- +- /* We now have a new epid to use. Initiate it. */ +- set_bit(epid, (void *)&epid_usage_bitmask); +- +- devnum = usb_pipedevice(urb->pipe); +- endpoint = usb_pipeendpoint(urb->pipe); +- slow = usb_pipeslow(urb->pipe); +- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); +- if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- /* We want both IN and OUT control traffic to be put on the same EP/SB list. */ +- out_traffic = 1; +- } else { +- out_traffic = usb_pipeout(urb->pipe); +- } +- +- save_flags(flags); +- cli(); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- +- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- *R_USB_EPT_DATA_ISO = IO_STATE(R_USB_EPT_DATA_ISO, valid, yes) | +- /* FIXME: Change any to the actual port? */ +- IO_STATE(R_USB_EPT_DATA_ISO, port, any) | +- IO_FIELD(R_USB_EPT_DATA_ISO, max_len, maxlen) | +- IO_FIELD(R_USB_EPT_DATA_ISO, ep, endpoint) | +- IO_FIELD(R_USB_EPT_DATA_ISO, dev, devnum); +- } else { +- *R_USB_EPT_DATA = IO_STATE(R_USB_EPT_DATA, valid, yes) | +- IO_FIELD(R_USB_EPT_DATA, low_speed, slow) | +- /* FIXME: Change any to the actual port? */ +- IO_STATE(R_USB_EPT_DATA, port, any) | +- IO_FIELD(R_USB_EPT_DATA, max_len, maxlen) | +- IO_FIELD(R_USB_EPT_DATA, ep, endpoint) | +- IO_FIELD(R_USB_EPT_DATA, dev, devnum); +- } +- +- restore_flags(flags); +- +- if (out_traffic) { +- set_bit(epid, (void *)&epid_out_traffic); +- } else { +- clear_bit(epid, (void *)&epid_out_traffic); +- } +- +- dbg_epid("Setting up epid %d with devnum %d, endpoint %d and max_len %d (%s)", +- epid, devnum, endpoint, maxlen, out_traffic ? "OUT" : "IN"); +- +- DBFEXIT; +- return epid; +-} +- +-static void etrax_usb_free_epid(int epid) +-{ +- unsigned long flags; +- +- DBFENTER; +- +- if (!test_bit(epid, (void *)&epid_usage_bitmask)) { +- warn("Trying to free unused epid %d", epid); +- DBFEXIT; +- return; +- } +- +- save_flags(flags); +- cli(); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- while (*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)); +- /* This will, among other things, set the valid field to 0. */ +- *R_USB_EPT_DATA = 0; +- restore_flags(flags); +- +- clear_bit(epid, (void *)&epid_usage_bitmask); +- +- +- dbg_epid("Freed epid %d", epid); +- +- DBFEXIT; +-} +- +-static int etrax_usb_lookup_epid(struct urb *urb) +-{ +- int i; +- __u32 data; +- char devnum, endpoint, slow, out_traffic; +- int maxlen; +- unsigned long flags; +- +- DBFENTER; +- +- devnum = usb_pipedevice(urb->pipe); +- endpoint = usb_pipeendpoint(urb->pipe); +- slow = usb_pipeslow(urb->pipe); +- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); +- if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- /* We want both IN and OUT control traffic to be put on the same EP/SB list. */ +- out_traffic = 1; +- } else { +- out_traffic = usb_pipeout(urb->pipe); +- } +- +- /* Step through att epids. */ +- for (i = 0; i < NBR_OF_EPIDS; i++) { +- if (test_bit(i, (void *)&epid_usage_bitmask) && +- test_bit(i, (void *)&epid_out_traffic) == out_traffic) { +- +- save_flags(flags); +- cli(); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, i); +- nop(); +- +- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- data = *R_USB_EPT_DATA_ISO; +- restore_flags(flags); +- +- if ((IO_MASK(R_USB_EPT_DATA_ISO, valid) & data) && +- (IO_EXTRACT(R_USB_EPT_DATA_ISO, dev, data) == devnum) && +- (IO_EXTRACT(R_USB_EPT_DATA_ISO, ep, data) == endpoint) && +- (IO_EXTRACT(R_USB_EPT_DATA_ISO, max_len, data) == maxlen)) { +- dbg_epid("Found epid %d for devnum %d, endpoint %d (%s)", +- i, devnum, endpoint, out_traffic ? "OUT" : "IN"); +- DBFEXIT; +- return i; +- } +- } else { +- data = *R_USB_EPT_DATA; +- restore_flags(flags); +- +- if ((IO_MASK(R_USB_EPT_DATA, valid) & data) && +- (IO_EXTRACT(R_USB_EPT_DATA, dev, data) == devnum) && +- (IO_EXTRACT(R_USB_EPT_DATA, ep, data) == endpoint) && +- (IO_EXTRACT(R_USB_EPT_DATA, low_speed, data) == slow) && +- (IO_EXTRACT(R_USB_EPT_DATA, max_len, data) == maxlen)) { +- dbg_epid("Found epid %d for devnum %d, endpoint %d (%s)", +- i, devnum, endpoint, out_traffic ? "OUT" : "IN"); +- DBFEXIT; +- return i; +- } +- } +- } +- } +- +- DBFEXIT; +- return -1; +-} +- +-static int etrax_usb_allocate_epid(void) +-{ +- int i; +- +- DBFENTER; +- +- for (i = 0; i < NBR_OF_EPIDS; i++) { +- if (!test_bit(i, (void *)&epid_usage_bitmask)) { +- dbg_epid("Found free epid %d", i); +- DBFEXIT; +- return i; +- } +- } +- +- dbg_epid("Found no free epids"); +- DBFEXIT; +- return -1; +-} +- +-static int etrax_usb_submit_urb(struct urb *urb, unsigned mem_flags) +-{ +- etrax_hc_t *hc; +- int ret = -EINVAL; +- +- DBFENTER; +- +- if (!urb->dev || !urb->dev->bus) { +- return -ENODEV; +- } +- if (usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)) <= 0) { +- info("Submit urb to pipe with maxpacketlen 0, pipe 0x%X\n", urb->pipe); +- return -EMSGSIZE; +- } +- +- if (urb->timeout) { +- /* FIXME. */ +- warn("urb->timeout specified, ignoring."); +- } +- +- hc = (etrax_hc_t*)urb->dev->bus->hcpriv; +- +- if (usb_pipedevice(urb->pipe) == hc->rh.devnum) { +- /* This request is for the Virtual Root Hub. */ +- ret = etrax_rh_submit_urb(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_BULK) { +- +- ret = etrax_usb_submit_bulk_urb(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- +- ret = etrax_usb_submit_ctrl_urb(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_INTERRUPT) { +- int bustime; +- +- if (urb->bandwidth == 0) { +- bustime = usb_check_bandwidth(urb->dev, urb); +- if (bustime < 0) { +- ret = bustime; +- } else { +- ret = etrax_usb_submit_intr_urb(urb); +- if (ret == 0) +- usb_claim_bandwidth(urb->dev, urb, bustime, 0); +- } +- } else { +- /* Bandwidth already set. */ +- ret = etrax_usb_submit_intr_urb(urb); +- } +- +- } else if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- int bustime; +- +- if (urb->bandwidth == 0) { +- bustime = usb_check_bandwidth(urb->dev, urb); +- if (bustime < 0) { +- ret = bustime; +- } else { +- ret = etrax_usb_submit_isoc_urb(urb); +- if (ret == 0) +- usb_claim_bandwidth(urb->dev, urb, bustime, 0); +- } +- } else { +- /* Bandwidth already set. */ +- ret = etrax_usb_submit_isoc_urb(urb); +- } +- } +- +- DBFEXIT; +- +- if (ret != 0) +- printk("Submit URB error %d\n", ret); +- +- return ret; +-} +- +-static int etrax_usb_unlink_urb(struct urb *urb, int status) +-{ +- etrax_hc_t *hc; +- etrax_urb_priv_t *urb_priv; +- int epid; +- unsigned int flags; +- +- DBFENTER; +- +- if (!urb) { +- return -EINVAL; +- } +- +- /* Disable interrupts here since a descriptor interrupt for the isoc epid +- will modify the sb list. This could possibly be done more granular, but +- unlink_urb should not be used frequently anyway. +- */ +- +- save_flags(flags); +- cli(); +- +- if (!urb->dev || !urb->dev->bus) { +- restore_flags(flags); +- return -ENODEV; +- } +- if (!urb->hcpriv) { +- /* This happens if a device driver calls unlink on an urb that +- was never submitted (lazy driver) or if the urb was completed +- while unlink was being called. */ +- restore_flags(flags); +- return 0; +- } +- if (urb->transfer_flags & URB_ASYNC_UNLINK) { +- /* FIXME. */ +- /* If URB_ASYNC_UNLINK is set: +- unlink +- move to a separate urb list +- call complete at next sof with ECONNRESET +- +- If not: +- wait 1 ms +- unlink +- call complete with ENOENT +- */ +- warn("URB_ASYNC_UNLINK set, ignoring."); +- } +- +- /* One might think that urb->status = -EINPROGRESS would be a requirement for unlinking, +- but that doesn't work for interrupt and isochronous traffic since they are completed +- repeatedly, and urb->status is set then. That may in itself be a bug though. */ +- +- hc = urb->dev->bus->hcpriv; +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- epid = urb_priv->epid; +- +- /* Set the urb status (synchronous unlink). */ +- urb->status = -ENOENT; +- urb_priv->urb_state = UNLINK; +- +- if (usb_pipedevice(urb->pipe) == hc->rh.devnum) { +- int ret; +- ret = etrax_rh_unlink_urb(urb); +- DBFEXIT; +- restore_flags(flags); +- return ret; +- +- } else if (usb_pipetype(urb->pipe) == PIPE_BULK) { +- +- dbg_bulk("Unlink of bulk urb (0x%lx)", (unsigned long)urb); +- +- if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { +- /* The EP was enabled, disable it and wait. */ +- TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); +- +- /* Ah, the luxury of busy-wait. */ +- while (*R_DMA_CH8_SUB0_EP == virt_to_phys(&TxBulkEPList[epid])); +- } +- /* Kicking dummy list out of the party. */ +- TxBulkEPList[epid].next = virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- +- dbg_ctrl("Unlink of ctrl urb (0x%lx)", (unsigned long)urb); +- +- if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) { +- /* The EP was enabled, disable it and wait. */ +- TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); +- +- /* Ah, the luxury of busy-wait. */ +- while (*R_DMA_CH8_SUB1_EP == virt_to_phys(&TxCtrlEPList[epid])); +- } +- +- } else if (usb_pipetype(urb->pipe) == PIPE_INTERRUPT) { +- +- dbg_intr("Unlink of intr urb (0x%lx)", (unsigned long)urb); +- +- /* Separate function because it's a tad more complicated. */ +- etrax_usb_unlink_intr_urb(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- +- dbg_isoc("Unlink of isoc urb (0x%lx)", (unsigned long)urb); +- +- if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { +- /* The EP was enabled, disable it and wait. */ +- TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); +- +- /* Ah, the luxury of busy-wait. */ +- while (*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])); +- } +- } +- +- /* Note that we need to remove the urb from the urb list *before* removing its SB +- descriptors. (This means that the isoc eof handler might get a null urb when we +- are unlinking the last urb.) */ +- +- if (usb_pipetype(urb->pipe) == PIPE_BULK) { +- +- urb_list_del(urb, epid); +- TxBulkEPList[epid].sub = 0; +- etrax_remove_from_sb_list(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- +- urb_list_del(urb, epid); +- TxCtrlEPList[epid].sub = 0; +- etrax_remove_from_sb_list(urb); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_INTERRUPT) { +- +- urb_list_del(urb, epid); +- /* Sanity check (should never happen). */ +- assert(urb_list_empty(epid)); +- +- /* Release allocated bandwidth. */ +- usb_release_bandwidth(urb->dev, urb, 0); +- +- } else if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- +- if (usb_pipeout(urb->pipe)) { +- +- USB_SB_Desc_t *iter_sb, *prev_sb, *next_sb; +- +- if (__urb_list_entry(urb, epid)) { +- +- urb_list_del(urb, epid); +- iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0; +- prev_sb = 0; +- while (iter_sb && (iter_sb != urb_priv->first_sb)) { +- prev_sb = iter_sb; +- iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; +- } +- +- if (iter_sb == 0) { +- /* Unlink of the URB currently being transmitted. */ +- prev_sb = 0; +- iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0; +- } +- +- while (iter_sb && (iter_sb != urb_priv->last_sb)) { +- iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; +- } +- if (iter_sb) { +- next_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; +- } else { +- /* This should only happen if the DMA has completed +- processing the SB list for this EP while interrupts +- are disabled. */ +- dbg_isoc("Isoc urb not found, already sent?"); +- next_sb = 0; +- } +- if (prev_sb) { +- prev_sb->next = next_sb ? virt_to_phys(next_sb) : 0; +- } else { +- TxIsocEPList[epid].sub = next_sb ? virt_to_phys(next_sb) : 0; +- } +- +- etrax_remove_from_sb_list(urb); +- if (urb_list_empty(epid)) { +- TxIsocEPList[epid].sub = 0; +- dbg_isoc("Last isoc out urb epid %d", epid); +- } else if (next_sb || prev_sb) { +- dbg_isoc("Re-enable isoc out epid %d", epid); +- +- TxIsocEPList[epid].hw_len = 0; +- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- } else { +- TxIsocEPList[epid].sub = 0; +- dbg_isoc("URB list non-empty and no SB list, EP disabled"); +- } +- } else { +- dbg_isoc("Urb 0x%p not found, completed already?", urb); +- } +- } else { +- +- urb_list_del(urb, epid); +- +- /* For in traffic there is only one SB descriptor for each EP even +- though there may be several urbs (all urbs point at the same SB). */ +- if (urb_list_empty(epid)) { +- /* No more urbs, remove the SB. */ +- TxIsocEPList[epid].sub = 0; +- etrax_remove_from_sb_list(urb); +- } else { +- TxIsocEPList[epid].hw_len = 0; +- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- } +- } +- /* Release allocated bandwidth. */ +- usb_release_bandwidth(urb->dev, urb, 1); +- } +- /* Free the epid if urb list is empty. */ +- if (urb_list_empty(epid)) { +- etrax_usb_free_epid(epid); +- } +- restore_flags(flags); +- +- /* Must be done before calling completion handler. */ +- kfree(urb_priv); +- urb->hcpriv = 0; +- +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- +- DBFEXIT; +- return 0; +-} +- +-static int etrax_usb_get_frame_number(struct usb_device *usb_dev) +-{ +- DBFENTER; +- DBFEXIT; +- return (*R_USB_FM_NUMBER & 0x7ff); +-} +- +-static irqreturn_t etrax_usb_tx_interrupt(int irq, void *vhc) +-{ +- DBFENTER; +- +- /* This interrupt handler could be used when unlinking EP descriptors. */ +- +- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub0_descr)) { +- USB_EP_Desc_t *ep; +- +- //dbg_bulk("dma8_sub0_descr (BULK) intr."); +- +- /* It should be safe clearing the interrupt here, since we don't expect to get a new +- one until we restart the bulk channel. */ +- *R_DMA_CH8_SUB0_CLR_INTR = IO_STATE(R_DMA_CH8_SUB0_CLR_INTR, clr_descr, do); +- +- /* Wait while the DMA is running (though we don't expect it to be). */ +- while (*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd)); +- +- /* Advance the DMA to the next EP descriptor. */ +- ep = (USB_EP_Desc_t *)phys_to_virt(*R_DMA_CH8_SUB0_EP); +- +- //dbg_bulk("descr intr: DMA is at 0x%lx", (unsigned long)ep); +- +- /* ep->next is already a physical address; no need for a virt_to_phys. */ +- *R_DMA_CH8_SUB0_EP = ep->next; +- +- /* Start the DMA bulk channel again. */ +- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); +- } +- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub1_descr)) { +- struct urb *urb; +- int epid; +- etrax_urb_priv_t *urb_priv; +- unsigned long int flags; +- +- dbg_ctrl("dma8_sub1_descr (CTRL) intr."); +- *R_DMA_CH8_SUB1_CLR_INTR = IO_STATE(R_DMA_CH8_SUB1_CLR_INTR, clr_descr, do); +- +- /* The complete callback gets called so we cli. */ +- save_flags(flags); +- cli(); +- +- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { +- if ((TxCtrlEPList[epid].sub == 0) || +- (epid == DUMMY_EPID) || +- (epid == INVALID_EPID)) { +- /* Nothing here to see. */ +- continue; +- } +- +- /* Get the first urb (if any). */ +- urb = urb_list_first(epid); +- +- if (urb) { +- +- /* Sanity check. */ +- assert(usb_pipetype(urb->pipe) == PIPE_CONTROL); +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- if (urb_priv->urb_state == WAITING_FOR_DESCR_INTR) { +- assert(!(TxCtrlEPList[urb_priv->epid].command & IO_MASK(USB_EP_command, enable))); +- +- etrax_usb_complete_urb(urb, 0); +- } +- } +- } +- restore_flags(flags); +- } +- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub2_descr)) { +- dbg_intr("dma8_sub2_descr (INTR) intr."); +- *R_DMA_CH8_SUB2_CLR_INTR = IO_STATE(R_DMA_CH8_SUB2_CLR_INTR, clr_descr, do); +- } +- if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub3_descr)) { +- struct urb *urb; +- int epid; +- int epid_done; +- etrax_urb_priv_t *urb_priv; +- USB_SB_Desc_t *sb_desc; +- +- usb_isoc_complete_data_t *comp_data = NULL; +- +- /* One or more isoc out transfers are done. */ +- dbg_isoc("dma8_sub3_descr (ISOC) intr."); +- +- /* For each isoc out EP search for the first sb_desc with the intr flag +- set. This descriptor must be the last packet from an URB. Then +- traverse the URB list for the EP until the URB with urb_priv->last_sb +- matching the intr-marked sb_desc is found. All URBs before this have +- been sent. +- */ +- +- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { +- /* Skip past epids with no SB lists, epids used for in traffic, +- and special (dummy, invalid) epids. */ +- if ((TxIsocEPList[epid].sub == 0) || +- (test_bit(epid, (void *)&epid_out_traffic) == 0) || +- (epid == DUMMY_EPID) || +- (epid == INVALID_EPID)) { +- /* Nothing here to see. */ +- continue; +- } +- sb_desc = phys_to_virt(TxIsocEPList[epid].sub); +- +- /* Find the last descriptor of the currently active URB for this ep. +- This is the first descriptor in the sub list marked for a descriptor +- interrupt. */ +- while (sb_desc && !IO_EXTRACT(USB_SB_command, intr, sb_desc->command)) { +- sb_desc = sb_desc->next ? phys_to_virt(sb_desc->next) : 0; +- } +- assert(sb_desc); +- +- dbg_isoc("Check epid %d, sub 0x%p, SB 0x%p", +- epid, +- phys_to_virt(TxIsocEPList[epid].sub), +- sb_desc); +- +- epid_done = 0; +- +- /* Get the first urb (if any). */ +- urb = urb_list_first(epid); +- assert(urb); +- +- while (urb && !epid_done) { +- +- /* Sanity check. */ +- assert(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); +- +- if (!usb_pipeout(urb->pipe)) { +- /* descr interrupts are generated only for out pipes. */ +- epid_done = 1; +- continue; +- } +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- if (sb_desc != urb_priv->last_sb) { +- +- /* This urb has been sent. */ +- dbg_isoc("out URB 0x%p sent", urb); +- +- urb_priv->urb_state = TRANSFER_DONE; +- +- } else if ((sb_desc == urb_priv->last_sb) && +- !(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { +- +- assert((sb_desc->command & IO_MASK(USB_SB_command, eol)) == IO_STATE(USB_SB_command, eol, yes)); +- assert(sb_desc->next == 0); +- +- dbg_isoc("out URB 0x%p last in list, epid disabled", urb); +- TxIsocEPList[epid].sub = 0; +- TxIsocEPList[epid].hw_len = 0; +- urb_priv->urb_state = TRANSFER_DONE; +- +- epid_done = 1; +- +- } else { +- epid_done = 1; +- } +- if (!epid_done) { +- urb = urb_list_next(urb, epid); +- } +- } +- +- } +- +- *R_DMA_CH8_SUB3_CLR_INTR = IO_STATE(R_DMA_CH8_SUB3_CLR_INTR, clr_descr, do); +- +- comp_data = (usb_isoc_complete_data_t*)kmem_cache_alloc(isoc_compl_cache, SLAB_ATOMIC); +- assert(comp_data != NULL); +- +- INIT_WORK(&comp_data->usb_bh, etrax_usb_isoc_descr_interrupt_bottom_half, comp_data); +- schedule_work(&comp_data->usb_bh); +- } +- +- DBFEXIT; +- return IRQ_HANDLED; +-} +- +-static void etrax_usb_isoc_descr_interrupt_bottom_half(void *data) +-{ +- usb_isoc_complete_data_t *comp_data = (usb_isoc_complete_data_t*)data; +- +- struct urb *urb; +- int epid; +- int epid_done; +- etrax_urb_priv_t *urb_priv; +- +- DBFENTER; +- +- dbg_isoc("dma8_sub3_descr (ISOC) bottom half."); +- +- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { +- unsigned long flags; +- +- save_flags(flags); +- cli(); +- +- epid_done = 0; +- +- /* The descriptor interrupt handler has marked all transmitted isoch. out +- URBs with TRANSFER_DONE. Now we traverse all epids and for all that +- have isoch. out traffic traverse its URB list and complete the +- transmitted URB. +- */ +- +- while (!epid_done) { +- +- /* Get the first urb (if any). */ +- urb = urb_list_first(epid); +- if (urb == 0) { +- epid_done = 1; +- continue; +- } +- +- if (usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) { +- epid_done = 1; +- continue; +- } +- +- if (!usb_pipeout(urb->pipe)) { +- /* descr interrupts are generated only for out pipes. */ +- epid_done = 1; +- continue; +- } +- +- dbg_isoc("Check epid %d, SB 0x%p", epid, (char*)TxIsocEPList[epid].sub); +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- if (urb_priv->urb_state == TRANSFER_DONE) { +- int i; +- struct usb_iso_packet_descriptor *packet; +- +- /* This urb has been sent. */ +- dbg_isoc("Completing isoc out URB 0x%p", urb); +- +- for (i = 0; i < urb->number_of_packets; i++) { +- packet = &urb->iso_frame_desc[i]; +- packet->status = 0; +- packet->actual_length = packet->length; +- } +- +- etrax_usb_complete_isoc_urb(urb, 0); +- +- if (urb_list_empty(epid)) { +- etrax_usb_free_epid(epid); +- epid_done = 1; +- } +- } else { +- epid_done = 1; +- } +- } +- restore_flags(flags); +- +- } +- kmem_cache_free(isoc_compl_cache, comp_data); +- +- DBFEXIT; +-} +- +- +- +-static irqreturn_t etrax_usb_rx_interrupt(int irq, void *vhc) +-{ +- struct urb *urb; +- etrax_urb_priv_t *urb_priv; +- int epid = 0; +- unsigned long flags; +- +- /* Isoc diagnostics. */ +- static int curr_fm = 0; +- static int prev_fm = 0; +- +- DBFENTER; +- +- /* Clear this interrupt. */ +- *R_DMA_CH9_CLR_INTR = IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, do); +- +- /* Note that this while loop assumes that all packets span only +- one rx descriptor. */ +- +- /* The reason we cli here is that we call the driver's callback functions. */ +- save_flags(flags); +- cli(); +- +- while (myNextRxDesc->status & IO_MASK(USB_IN_status, eop)) { +- +- epid = IO_EXTRACT(USB_IN_status, epid, myNextRxDesc->status); +- urb = urb_list_first(epid); +- +- //printk("eop for epid %d, first urb 0x%lx\n", epid, (unsigned long)urb); +- +- if (!urb) { +- err("No urb for epid %d in rx interrupt", epid); +- __dump_ept_data(epid); +- goto skip_out; +- } +- +- /* Note that we cannot indescriminately assert(usb_pipein(urb->pipe)) since +- ctrl pipes are not. */ +- +- if (myNextRxDesc->status & IO_MASK(USB_IN_status, error)) { +- __u32 r_usb_ept_data; +- int no_error = 0; +- +- assert(test_bit(epid, (void *)&epid_usage_bitmask)); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- r_usb_ept_data = *R_USB_EPT_DATA_ISO; +- +- if ((r_usb_ept_data & IO_MASK(R_USB_EPT_DATA_ISO, valid)) && +- (IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data) == 0) && +- (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata))) { +- /* Not an error, just a failure to receive an expected iso +- in packet in this frame. This is not documented +- in the designers reference. +- */ +- no_error++; +- } else { +- warn("R_USB_EPT_DATA_ISO for epid %d = 0x%x", epid, r_usb_ept_data); +- } +- } else { +- r_usb_ept_data = *R_USB_EPT_DATA; +- warn("R_USB_EPT_DATA for epid %d = 0x%x", epid, r_usb_ept_data); +- } +- +- if (!no_error){ +- warn("error in rx desc->status, epid %d, first urb = 0x%lx", +- epid, (unsigned long)urb); +- __dump_in_desc(myNextRxDesc); +- +- warn("R_USB_STATUS = 0x%x", *R_USB_STATUS); +- +- /* Check that ept was disabled when error occurred. */ +- switch (usb_pipetype(urb->pipe)) { +- case PIPE_BULK: +- assert(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- break; +- case PIPE_CONTROL: +- assert(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- break; +- case PIPE_INTERRUPT: +- assert(!(TxIntrEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- break; +- case PIPE_ISOCHRONOUS: +- assert(!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- break; +- default: +- warn("etrax_usb_rx_interrupt: bad pipetype %d in urb 0x%p", +- usb_pipetype(urb->pipe), +- urb); +- } +- etrax_usb_complete_urb(urb, -EPROTO); +- goto skip_out; +- } +- } +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- if ((usb_pipetype(urb->pipe) == PIPE_BULK) || +- (usb_pipetype(urb->pipe) == PIPE_CONTROL) || +- (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) { +- +- if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { +- /* We get nodata for empty data transactions, and the rx descriptor's +- hw_len field is not valid in that case. No data to copy in other +- words. */ +- } else { +- /* Make sure the data fits in the buffer. */ +- assert(urb_priv->rx_offset + myNextRxDesc->hw_len +- <= urb->transfer_buffer_length); +- +- memcpy(urb->transfer_buffer + urb_priv->rx_offset, +- phys_to_virt(myNextRxDesc->buf), myNextRxDesc->hw_len); +- urb_priv->rx_offset += myNextRxDesc->hw_len; +- } +- +- if (myNextRxDesc->status & IO_MASK(USB_IN_status, eot)) { +- if ((usb_pipetype(urb->pipe) == PIPE_CONTROL) && +- ((TxCtrlEPList[urb_priv->epid].command & IO_MASK(USB_EP_command, enable)) == +- IO_STATE(USB_EP_command, enable, yes))) { +- /* The EP is still enabled, so the OUT packet used to ack +- the in data is probably not processed yet. If the EP +- sub pointer has not moved beyond urb_priv->last_sb mark +- it for a descriptor interrupt and complete the urb in +- the descriptor interrupt handler. +- */ +- USB_SB_Desc_t *sub = TxCtrlEPList[urb_priv->epid].sub ? phys_to_virt(TxCtrlEPList[urb_priv->epid].sub) : 0; +- +- while ((sub != NULL) && (sub != urb_priv->last_sb)) { +- sub = sub->next ? phys_to_virt(sub->next) : 0; +- } +- if (sub != NULL) { +- /* The urb has not been fully processed. */ +- urb_priv->urb_state = WAITING_FOR_DESCR_INTR; +- } else { +- warn("(CTRL) epid enabled and urb (0x%p) processed, ep->sub=0x%p", urb, (char*)TxCtrlEPList[urb_priv->epid].sub); +- etrax_usb_complete_urb(urb, 0); +- } +- } else { +- etrax_usb_complete_urb(urb, 0); +- } +- } +- +- } else if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- +- struct usb_iso_packet_descriptor *packet; +- +- if (urb_priv->urb_state == UNLINK) { +- info("Ignoring rx data for urb being unlinked."); +- goto skip_out; +- } else if (urb_priv->urb_state == NOT_STARTED) { +- info("What? Got rx data for urb that isn't started?"); +- goto skip_out; +- } +- +- packet = &urb->iso_frame_desc[urb_priv->isoc_packet_counter]; +- packet->status = 0; +- +- if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { +- /* We get nodata for empty data transactions, and the rx descriptor's +- hw_len field is not valid in that case. We copy 0 bytes however to +- stay in synch. */ +- packet->actual_length = 0; +- } else { +- packet->actual_length = myNextRxDesc->hw_len; +- /* Make sure the data fits in the buffer. */ +- assert(packet->actual_length <= packet->length); +- memcpy(urb->transfer_buffer + packet->offset, +- phys_to_virt(myNextRxDesc->buf), packet->actual_length); +- } +- +- /* Increment the packet counter. */ +- urb_priv->isoc_packet_counter++; +- +- /* Note that we don't care about the eot field in the rx descriptor's status. +- It will always be set for isoc traffic. */ +- if (urb->number_of_packets == urb_priv->isoc_packet_counter) { +- +- /* Out-of-synch diagnostics. */ +- curr_fm = (*R_USB_FM_NUMBER & 0x7ff); +- if (((prev_fm + urb_priv->isoc_packet_counter) % (0x7ff + 1)) != curr_fm) { +- /* This test is wrong, if there is more than one isoc +- in endpoint active it will always calculate wrong +- since prev_fm is shared by all endpoints. +- +- FIXME Make this check per URB using urb->start_frame. +- */ +- dbg_isoc("Out of synch? Previous frame = %d, current frame = %d", +- prev_fm, curr_fm); +- +- } +- prev_fm = curr_fm; +- +- /* Complete the urb with status OK. */ +- etrax_usb_complete_isoc_urb(urb, 0); +- } +- } +- +- skip_out: +- +- /* DMA IN cache bug. Flush the DMA IN buffer from the cache. (struct etrax_dma_descr +- has the same layout as USB_IN_Desc for the relevant fields.) */ +- prepare_rx_descriptor((struct etrax_dma_descr*)myNextRxDesc); +- +- myPrevRxDesc = myNextRxDesc; +- myPrevRxDesc->command |= IO_MASK(USB_IN_command, eol); +- myLastRxDesc->command &= ~IO_MASK(USB_IN_command, eol); +- myLastRxDesc = myPrevRxDesc; +- +- myNextRxDesc->status = 0; +- myNextRxDesc = phys_to_virt(myNextRxDesc->next); +- } +- +- restore_flags(flags); +- +- DBFEXIT; +- +- return IRQ_HANDLED; +-} +- +- +-/* This function will unlink the SB descriptors associated with this urb. */ +-static int etrax_remove_from_sb_list(struct urb *urb) +-{ +- USB_SB_Desc_t *next_sb, *first_sb, *last_sb; +- etrax_urb_priv_t *urb_priv; +- int i = 0; +- +- DBFENTER; +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- /* Just a sanity check. Since we don't fiddle with the DMA list the EP descriptor +- doesn't really need to be disabled, it's just that we expect it to be. */ +- if (usb_pipetype(urb->pipe) == PIPE_BULK) { +- assert(!(TxBulkEPList[urb_priv->epid].command & IO_MASK(USB_EP_command, enable))); +- } else if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { +- assert(!(TxCtrlEPList[urb_priv->epid].command & IO_MASK(USB_EP_command, enable))); +- } +- +- first_sb = urb_priv->first_sb; +- last_sb = urb_priv->last_sb; +- +- assert(first_sb); +- assert(last_sb); +- +- while (first_sb != last_sb) { +- next_sb = (USB_SB_Desc_t *)phys_to_virt(first_sb->next); +- kmem_cache_free(usb_desc_cache, first_sb); +- first_sb = next_sb; +- i++; +- } +- kmem_cache_free(usb_desc_cache, last_sb); +- i++; +- dbg_sb("%d SB descriptors freed", i); +- /* Compare i with urb->number_of_packets for Isoc traffic. +- Should be same when calling unlink_urb */ +- +- DBFEXIT; +- +- return i; +-} +- +-static int etrax_usb_submit_bulk_urb(struct urb *urb) +-{ +- int epid; +- int empty; +- unsigned long flags; +- etrax_urb_priv_t *urb_priv; +- +- DBFENTER; +- +- /* Epid allocation, empty check and list add must be protected. +- Read about this in etrax_usb_submit_ctrl_urb. */ +- +- spin_lock_irqsave(&urb_list_lock, flags); +- epid = etrax_usb_setup_epid(urb); +- if (epid == -1) { +- DBFEXIT; +- spin_unlock_irqrestore(&urb_list_lock, flags); +- return -ENOMEM; +- } +- empty = urb_list_empty(epid); +- urb_list_add(urb, epid); +- spin_unlock_irqrestore(&urb_list_lock, flags); +- +- dbg_bulk("Adding bulk %s urb 0x%lx to %s list, epid %d", +- usb_pipein(urb->pipe) ? "IN" : "OUT", (unsigned long)urb, empty ? "empty" : "", epid); +- +- /* Mark the urb as being in progress. */ +- urb->status = -EINPROGRESS; +- +- /* Setup the hcpriv data. */ +- urb_priv = kzalloc(sizeof(etrax_urb_priv_t), KMALLOC_FLAG); +- assert(urb_priv != NULL); +- /* This sets rx_offset to 0. */ +- urb_priv->urb_state = NOT_STARTED; +- urb->hcpriv = urb_priv; +- +- if (empty) { +- etrax_usb_add_to_bulk_sb_list(urb, epid); +- } +- +- DBFEXIT; +- +- return 0; +-} +- +-static void etrax_usb_add_to_bulk_sb_list(struct urb *urb, int epid) +-{ +- USB_SB_Desc_t *sb_desc; +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- unsigned long flags; +- char maxlen; +- +- DBFENTER; +- +- dbg_bulk("etrax_usb_add_to_bulk_sb_list, urb 0x%lx", (unsigned long)urb); +- +- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); +- +- sb_desc = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(sb_desc != NULL); +- memset(sb_desc, 0, sizeof(USB_SB_Desc_t)); +- +- +- if (usb_pipeout(urb->pipe)) { +- +- dbg_bulk("Grabbing bulk OUT, urb 0x%lx, epid %d", (unsigned long)urb, epid); +- +- /* This is probably a sanity check of the bulk transaction length +- not being larger than 64 kB. */ +- if (urb->transfer_buffer_length > 0xffff) { +- panic("urb->transfer_buffer_length > 0xffff"); +- } +- +- sb_desc->sw_len = urb->transfer_buffer_length; +- +- /* The rem field is don't care if it's not a full-length transfer, so setting +- it shouldn't hurt. Also, rem isn't used for OUT traffic. */ +- sb_desc->command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, out) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- /* The full field is set to yes, even if we don't actually check that this is +- a full-length transfer (i.e., that transfer_buffer_length % maxlen = 0). +- Setting full prevents the USB controller from sending an empty packet in +- that case. However, if URB_ZERO_PACKET was set we want that. */ +- if (!(urb->transfer_flags & URB_ZERO_PACKET)) { +- sb_desc->command |= IO_STATE(USB_SB_command, full, yes); +- } +- +- sb_desc->buf = virt_to_phys(urb->transfer_buffer); +- sb_desc->next = 0; +- +- } else if (usb_pipein(urb->pipe)) { +- +- dbg_bulk("Grabbing bulk IN, urb 0x%lx, epid %d", (unsigned long)urb, epid); +- +- sb_desc->sw_len = urb->transfer_buffer_length ? +- (urb->transfer_buffer_length - 1) / maxlen + 1 : 0; +- +- /* The rem field is don't care if it's not a full-length transfer, so setting +- it shouldn't hurt. */ +- sb_desc->command = +- (IO_FIELD(USB_SB_command, rem, +- urb->transfer_buffer_length % maxlen) | +- IO_STATE(USB_SB_command, tt, in) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- sb_desc->buf = 0; +- sb_desc->next = 0; +- } +- +- urb_priv->first_sb = sb_desc; +- urb_priv->last_sb = sb_desc; +- urb_priv->epid = epid; +- +- urb->hcpriv = urb_priv; +- +- /* Reset toggle bits and reset error count. */ +- save_flags(flags); +- cli(); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- +- /* FIXME: Is this a special case since the hold field is checked, +- or should we check hold in a lot of other cases as well? */ +- if (*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) { +- panic("Hold was set in %s", __FUNCTION__); +- } +- +- /* Reset error counters (regardless of which direction this traffic is). */ +- *R_USB_EPT_DATA &= +- ~(IO_MASK(R_USB_EPT_DATA, error_count_in) | +- IO_MASK(R_USB_EPT_DATA, error_count_out)); +- +- /* Software must preset the toggle bits. */ +- if (usb_pipeout(urb->pipe)) { +- char toggle = +- usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), usb_pipeout(urb->pipe)); +- *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_out); +- *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_out, toggle); +- } else { +- char toggle = +- usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), usb_pipeout(urb->pipe)); +- *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_in); +- *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_in, toggle); +- } +- +- /* Assert that the EP descriptor is disabled. */ +- assert(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- +- /* The reason we set the EP's sub pointer directly instead of +- walking the SB list and linking it last in the list is that we only +- have one active urb at a time (the rest are queued). */ +- +- /* Note that we cannot have interrupts running when we have set the SB descriptor +- but the EP is not yet enabled. If a bulk eot happens for another EP, we will +- find this EP disabled and with a SB != 0, which will make us think that it's done. */ +- TxBulkEPList[epid].sub = virt_to_phys(sb_desc); +- TxBulkEPList[epid].hw_len = 0; +- /* Note that we don't have to fill in the ep_id field since this +- was done when we allocated the EP descriptors in init_tx_bulk_ep. */ +- +- /* Check if the dummy list is already with us (if several urbs were queued). */ +- if (TxBulkEPList[epid].next != virt_to_phys(&TxBulkDummyEPList[epid][0])) { +- +- dbg_bulk("Inviting dummy list to the party for urb 0x%lx, epid %d", +- (unsigned long)urb, epid); +- +- /* The last EP in the dummy list already has its next pointer set to +- TxBulkEPList[epid].next. */ +- +- /* We don't need to check if the DMA is at this EP or not before changing the +- next pointer, since we will do it in one 32-bit write (EP descriptors are +- 32-bit aligned). */ +- TxBulkEPList[epid].next = virt_to_phys(&TxBulkDummyEPList[epid][0]); +- } +- /* Enable the EP descr. */ +- dbg_bulk("Enabling bulk EP for urb 0x%lx, epid %d", (unsigned long)urb, epid); +- TxBulkEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- +- /* Everything is set up, safe to enable interrupts again. */ +- restore_flags(flags); +- +- /* If the DMA bulk channel isn't running, we need to restart it if it +- has stopped at the last EP descriptor (DMA stopped because there was +- no more traffic) or if it has stopped at a dummy EP with the intr flag +- set (DMA stopped because we were too slow in inserting new traffic). */ +- if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) { +- +- USB_EP_Desc_t *ep; +- ep = (USB_EP_Desc_t *)phys_to_virt(*R_DMA_CH8_SUB0_EP); +- dbg_bulk("DMA channel not running in add"); +- dbg_bulk("DMA is at 0x%lx", (unsigned long)ep); +- +- if (*R_DMA_CH8_SUB0_EP == virt_to_phys(&TxBulkEPList[NBR_OF_EPIDS - 1]) || +- (ep->command & 0x8) >> 3) { +- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); +- /* Update/restart the bulk start timer since we just started the channel. */ +- mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); +- /* Update/restart the bulk eot timer since we just inserted traffic. */ +- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); +- } +- } +- +- DBFEXIT; +-} +- +-static void etrax_usb_complete_bulk_urb(struct urb *urb, int status) +-{ +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- int epid = urb_priv->epid; +- unsigned long flags; +- +- DBFENTER; +- +- if (status) +- warn("Completing bulk urb with status %d.", status); +- +- dbg_bulk("Completing bulk urb 0x%lx for epid %d", (unsigned long)urb, epid); +- +- /* Update the urb list. */ +- urb_list_del(urb, epid); +- +- /* For an IN pipe, we always set the actual length, regardless of whether there was +- an error or not (which means the device driver can use the data if it wants to). */ +- if (usb_pipein(urb->pipe)) { +- urb->actual_length = urb_priv->rx_offset; +- } else { +- /* Set actual_length for OUT urbs also; the USB mass storage driver seems +- to want that. We wouldn't know of any partial writes if there was an error. */ +- if (status == 0) { +- urb->actual_length = urb->transfer_buffer_length; +- } else { +- urb->actual_length = 0; +- } +- } +- +- /* FIXME: Is there something of the things below we shouldn't do if there was an error? +- Like, maybe we shouldn't toggle the toggle bits, or maybe we shouldn't insert more traffic. */ +- +- save_flags(flags); +- cli(); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- +- /* We need to fiddle with the toggle bits because the hardware doesn't do it for us. */ +- if (usb_pipeout(urb->pipe)) { +- char toggle = +- IO_EXTRACT(R_USB_EPT_DATA, t_out, *R_USB_EPT_DATA); +- usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe), +- usb_pipeout(urb->pipe), toggle); +- } else { +- char toggle = +- IO_EXTRACT(R_USB_EPT_DATA, t_in, *R_USB_EPT_DATA); +- usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe), +- usb_pipeout(urb->pipe), toggle); +- } +- restore_flags(flags); +- +- /* Remember to free the SBs. */ +- etrax_remove_from_sb_list(urb); +- kfree(urb_priv); +- urb->hcpriv = 0; +- +- /* If there are any more urb's in the list we'd better start sending */ +- if (!urb_list_empty(epid)) { +- +- struct urb *new_urb; +- +- /* Get the first urb. */ +- new_urb = urb_list_first(epid); +- assert(new_urb); +- +- dbg_bulk("More bulk for epid %d", epid); +- +- etrax_usb_add_to_bulk_sb_list(new_urb, epid); +- } +- +- urb->status = status; +- +- /* We let any non-zero status from the layer above have precedence. */ +- if (status == 0) { +- /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's max length) +- is to be treated as an error. */ +- if (urb->transfer_flags & URB_SHORT_NOT_OK) { +- if (usb_pipein(urb->pipe) && +- (urb->actual_length != +- usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)))) { +- urb->status = -EREMOTEIO; +- } +- } +- } +- +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- +- if (urb_list_empty(epid)) { +- /* This means that this EP is now free, deconfigure it. */ +- etrax_usb_free_epid(epid); +- +- /* No more traffic; time to clean up. +- Must set sub pointer to 0, since we look at the sub pointer when handling +- the bulk eot interrupt. */ +- +- dbg_bulk("No bulk for epid %d", epid); +- +- TxBulkEPList[epid].sub = 0; +- +- /* Unlink the dummy list. */ +- +- dbg_bulk("Kicking dummy list out of party for urb 0x%lx, epid %d", +- (unsigned long)urb, epid); +- +- /* No need to wait for the DMA before changing the next pointer. +- The modulo NBR_OF_EPIDS isn't actually necessary, since we will never use +- the last one (INVALID_EPID) for actual traffic. */ +- TxBulkEPList[epid].next = +- virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); +- } +- +- DBFEXIT; +-} +- +-static int etrax_usb_submit_ctrl_urb(struct urb *urb) +-{ +- int epid; +- int empty; +- unsigned long flags; +- etrax_urb_priv_t *urb_priv; +- +- DBFENTER; +- +- /* FIXME: Return -ENXIO if there is already a queued urb for this endpoint? */ +- +- /* Epid allocation, empty check and list add must be protected. +- +- Epid allocation because if we find an existing epid for this endpoint an urb might be +- completed (emptying the list) before we add the new urb to the list, causing the epid +- to be de-allocated. We would then start the transfer with an invalid epid -> epid attn. +- +- Empty check and add because otherwise we might conclude that the list is not empty, +- after which it becomes empty before we add the new urb to the list, causing us not to +- insert the new traffic into the SB list. */ +- +- spin_lock_irqsave(&urb_list_lock, flags); +- epid = etrax_usb_setup_epid(urb); +- if (epid == -1) { +- spin_unlock_irqrestore(&urb_list_lock, flags); +- DBFEXIT; +- return -ENOMEM; +- } +- empty = urb_list_empty(epid); +- urb_list_add(urb, epid); +- spin_unlock_irqrestore(&urb_list_lock, flags); +- +- dbg_ctrl("Adding ctrl urb 0x%lx to %s list, epid %d", +- (unsigned long)urb, empty ? "empty" : "", epid); +- +- /* Mark the urb as being in progress. */ +- urb->status = -EINPROGRESS; +- +- /* Setup the hcpriv data. */ +- urb_priv = kzalloc(sizeof(etrax_urb_priv_t), KMALLOC_FLAG); +- assert(urb_priv != NULL); +- /* This sets rx_offset to 0. */ +- urb_priv->urb_state = NOT_STARTED; +- urb->hcpriv = urb_priv; +- +- if (empty) { +- etrax_usb_add_to_ctrl_sb_list(urb, epid); +- } +- +- DBFEXIT; +- +- return 0; +-} +- +-static void etrax_usb_add_to_ctrl_sb_list(struct urb *urb, int epid) +-{ +- USB_SB_Desc_t *sb_desc_setup; +- USB_SB_Desc_t *sb_desc_data; +- USB_SB_Desc_t *sb_desc_status; +- +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- +- unsigned long flags; +- char maxlen; +- +- DBFENTER; +- +- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); +- +- sb_desc_setup = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(sb_desc_setup != NULL); +- sb_desc_status = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(sb_desc_status != NULL); +- +- /* Initialize the mandatory setup SB descriptor (used only in control transfers) */ +- sb_desc_setup->sw_len = 8; +- sb_desc_setup->command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, setup) | +- IO_STATE(USB_SB_command, full, yes) | +- IO_STATE(USB_SB_command, eot, yes)); +- +- sb_desc_setup->buf = virt_to_phys(urb->setup_packet); +- +- if (usb_pipeout(urb->pipe)) { +- dbg_ctrl("Transfer for epid %d is OUT", epid); +- +- /* If this Control OUT transfer has an optional data stage we add an OUT token +- before the mandatory IN (status) token, hence the reordered SB list */ +- +- sb_desc_setup->next = virt_to_phys(sb_desc_status); +- if (urb->transfer_buffer) { +- +- dbg_ctrl("This OUT transfer has an extra data stage"); +- +- sb_desc_data = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(sb_desc_data != NULL); +- +- sb_desc_setup->next = virt_to_phys(sb_desc_data); +- +- sb_desc_data->sw_len = urb->transfer_buffer_length; +- sb_desc_data->command = (IO_STATE(USB_SB_command, tt, out) | +- IO_STATE(USB_SB_command, full, yes) | +- IO_STATE(USB_SB_command, eot, yes)); +- sb_desc_data->buf = virt_to_phys(urb->transfer_buffer); +- sb_desc_data->next = virt_to_phys(sb_desc_status); +- } +- +- sb_desc_status->sw_len = 1; +- sb_desc_status->command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, in) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, intr, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- sb_desc_status->buf = 0; +- sb_desc_status->next = 0; +- +- } else if (usb_pipein(urb->pipe)) { +- +- dbg_ctrl("Transfer for epid %d is IN", epid); +- dbg_ctrl("transfer_buffer_length = %d", urb->transfer_buffer_length); +- dbg_ctrl("rem is calculated to %d", urb->transfer_buffer_length % maxlen); +- +- sb_desc_data = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(sb_desc_data != NULL); +- +- sb_desc_setup->next = virt_to_phys(sb_desc_data); +- +- sb_desc_data->sw_len = urb->transfer_buffer_length ? +- (urb->transfer_buffer_length - 1) / maxlen + 1 : 0; +- dbg_ctrl("sw_len got %d", sb_desc_data->sw_len); +- +- sb_desc_data->command = +- (IO_FIELD(USB_SB_command, rem, +- urb->transfer_buffer_length % maxlen) | +- IO_STATE(USB_SB_command, tt, in) | +- IO_STATE(USB_SB_command, eot, yes)); +- +- sb_desc_data->buf = 0; +- sb_desc_data->next = virt_to_phys(sb_desc_status); +- +- /* Read comment at zout_buffer declaration for an explanation to this. */ +- sb_desc_status->sw_len = 1; +- sb_desc_status->command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, zout) | +- IO_STATE(USB_SB_command, full, yes) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, intr, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- sb_desc_status->buf = virt_to_phys(&zout_buffer[0]); +- sb_desc_status->next = 0; +- } +- +- urb_priv->first_sb = sb_desc_setup; +- urb_priv->last_sb = sb_desc_status; +- urb_priv->epid = epid; +- +- urb_priv->urb_state = STARTED; +- +- /* Reset toggle bits and reset error count, remember to di and ei */ +- /* Warning: it is possible that this locking doesn't work with bottom-halves */ +- +- save_flags(flags); +- cli(); +- +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- if (*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) { +- panic("Hold was set in %s", __FUNCTION__); +- } +- +- +- /* FIXME: Compare with etrax_usb_add_to_bulk_sb_list where the toggle bits +- are set to a specific value. Why the difference? Read "Transfer and Toggle Bits +- in Designer's Reference, p. 8 - 11. */ +- *R_USB_EPT_DATA &= +- ~(IO_MASK(R_USB_EPT_DATA, error_count_in) | +- IO_MASK(R_USB_EPT_DATA, error_count_out) | +- IO_MASK(R_USB_EPT_DATA, t_in) | +- IO_MASK(R_USB_EPT_DATA, t_out)); +- +- /* Since we use the rx interrupt to complete ctrl urbs, we can enable interrupts now +- (i.e. we don't check the sub pointer on an eot interrupt like we do for bulk traffic). */ +- restore_flags(flags); +- +- /* Assert that the EP descriptor is disabled. */ +- assert(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable))); +- +- /* Set up and enable the EP descriptor. */ +- TxCtrlEPList[epid].sub = virt_to_phys(sb_desc_setup); +- TxCtrlEPList[epid].hw_len = 0; +- TxCtrlEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- +- /* We start the DMA sub channel without checking if it's running or not, because: +- 1) If it's already running, issuing the start command is a nop. +- 2) We avoid a test-and-set race condition. */ +- *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start); +- +- DBFEXIT; +-} +- +-static void etrax_usb_complete_ctrl_urb(struct urb *urb, int status) +-{ +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- int epid = urb_priv->epid; +- +- DBFENTER; +- +- if (status) +- warn("Completing ctrl urb with status %d.", status); +- +- dbg_ctrl("Completing ctrl epid %d, urb 0x%lx", epid, (unsigned long)urb); +- +- /* Remove this urb from the list. */ +- urb_list_del(urb, epid); +- +- /* For an IN pipe, we always set the actual length, regardless of whether there was +- an error or not (which means the device driver can use the data if it wants to). */ +- if (usb_pipein(urb->pipe)) { +- urb->actual_length = urb_priv->rx_offset; +- } +- +- /* FIXME: Is there something of the things below we shouldn't do if there was an error? +- Like, maybe we shouldn't insert more traffic. */ +- +- /* Remember to free the SBs. */ +- etrax_remove_from_sb_list(urb); +- kfree(urb_priv); +- urb->hcpriv = 0; +- +- /* If there are any more urbs in the list we'd better start sending. */ +- if (!urb_list_empty(epid)) { +- struct urb *new_urb; +- +- /* Get the first urb. */ +- new_urb = urb_list_first(epid); +- assert(new_urb); +- +- dbg_ctrl("More ctrl for epid %d, first urb = 0x%lx", epid, (unsigned long)new_urb); +- +- etrax_usb_add_to_ctrl_sb_list(new_urb, epid); +- } +- +- urb->status = status; +- +- /* We let any non-zero status from the layer above have precedence. */ +- if (status == 0) { +- /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's max length) +- is to be treated as an error. */ +- if (urb->transfer_flags & URB_SHORT_NOT_OK) { +- if (usb_pipein(urb->pipe) && +- (urb->actual_length != +- usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)))) { +- urb->status = -EREMOTEIO; +- } +- } +- } +- +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- +- if (urb_list_empty(epid)) { +- /* No more traffic. Time to clean up. */ +- etrax_usb_free_epid(epid); +- /* Must set sub pointer to 0. */ +- dbg_ctrl("No ctrl for epid %d", epid); +- TxCtrlEPList[epid].sub = 0; +- } +- +- DBFEXIT; +-} +- +-static int etrax_usb_submit_intr_urb(struct urb *urb) +-{ +- +- int epid; +- +- DBFENTER; +- +- if (usb_pipeout(urb->pipe)) { +- /* Unsupported transfer type. +- We don't support interrupt out traffic. (If we do, we can't support +- intervals for neither in or out traffic, but are forced to schedule all +- interrupt traffic in one frame.) */ +- return -EINVAL; +- } +- +- epid = etrax_usb_setup_epid(urb); +- if (epid == -1) { +- DBFEXIT; +- return -ENOMEM; +- } +- +- if (!urb_list_empty(epid)) { +- /* There is already a queued urb for this endpoint. */ +- etrax_usb_free_epid(epid); +- return -ENXIO; +- } +- +- urb->status = -EINPROGRESS; +- +- dbg_intr("Add intr urb 0x%lx, to list, epid %d", (unsigned long)urb, epid); +- +- urb_list_add(urb, epid); +- etrax_usb_add_to_intr_sb_list(urb, epid); +- +- return 0; +- +- DBFEXIT; +-} +- +-static void etrax_usb_add_to_intr_sb_list(struct urb *urb, int epid) +-{ +- +- volatile USB_EP_Desc_t *tmp_ep; +- volatile USB_EP_Desc_t *first_ep; +- +- char maxlen; +- int interval; +- int i; +- +- etrax_urb_priv_t *urb_priv; +- +- DBFENTER; +- +- maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); +- interval = urb->interval; +- +- urb_priv = kzalloc(sizeof(etrax_urb_priv_t), KMALLOC_FLAG); +- assert(urb_priv != NULL); +- urb->hcpriv = urb_priv; +- +- first_ep = &TxIntrEPList[0]; +- +- /* Round of the interval to 2^n, it is obvious that this code favours +- smaller numbers, but that is actually a good thing */ +- /* FIXME: The "rounding error" for larger intervals will be quite +- large. For in traffic this shouldn't be a problem since it will only +- mean that we "poll" more often. */ +- for (i = 0; interval; i++) { +- interval = interval >> 1; +- } +- interval = 1 << (i - 1); +- +- dbg_intr("Interval rounded to %d", interval); +- +- tmp_ep = first_ep; +- i = 0; +- do { +- if (tmp_ep->command & IO_MASK(USB_EP_command, eof)) { +- if ((i % interval) == 0) { +- /* Insert the traffic ep after tmp_ep */ +- USB_EP_Desc_t *ep_desc; +- USB_SB_Desc_t *sb_desc; +- +- dbg_intr("Inserting EP for epid %d", epid); +- +- ep_desc = (USB_EP_Desc_t *) +- kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- sb_desc = (USB_SB_Desc_t *) +- kmem_cache_alloc(usb_desc_cache, SLAB_FLAG); +- assert(ep_desc != NULL); +- CHECK_ALIGN(ep_desc); +- assert(sb_desc != NULL); +- +- ep_desc->sub = virt_to_phys(sb_desc); +- ep_desc->hw_len = 0; +- ep_desc->command = (IO_FIELD(USB_EP_command, epid, epid) | +- IO_STATE(USB_EP_command, enable, yes)); +- +- +- /* Round upwards the number of packets of size maxlen +- that this SB descriptor should receive. */ +- sb_desc->sw_len = urb->transfer_buffer_length ? +- (urb->transfer_buffer_length - 1) / maxlen + 1 : 0; +- sb_desc->next = 0; +- sb_desc->buf = 0; +- sb_desc->command = +- (IO_FIELD(USB_SB_command, rem, urb->transfer_buffer_length % maxlen) | +- IO_STATE(USB_SB_command, tt, in) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- ep_desc->next = tmp_ep->next; +- tmp_ep->next = virt_to_phys(ep_desc); +- } +- i++; +- } +- tmp_ep = (USB_EP_Desc_t *)phys_to_virt(tmp_ep->next); +- } while (tmp_ep != first_ep); +- +- +- /* Note that first_sb/last_sb doesn't apply to interrupt traffic. */ +- urb_priv->epid = epid; +- +- /* We start the DMA sub channel without checking if it's running or not, because: +- 1) If it's already running, issuing the start command is a nop. +- 2) We avoid a test-and-set race condition. */ +- *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start); +- +- DBFEXIT; +-} +- +- +- +-static void etrax_usb_complete_intr_urb(struct urb *urb, int status) +-{ +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- int epid = urb_priv->epid; +- +- DBFENTER; +- +- if (status) +- warn("Completing intr urb with status %d.", status); +- +- dbg_intr("Completing intr epid %d, urb 0x%lx", epid, (unsigned long)urb); +- +- urb->status = status; +- urb->actual_length = urb_priv->rx_offset; +- +- dbg_intr("interrupt urb->actual_length = %d", urb->actual_length); +- +- /* We let any non-zero status from the layer above have precedence. */ +- if (status == 0) { +- /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's max length) +- is to be treated as an error. */ +- if (urb->transfer_flags & URB_SHORT_NOT_OK) { +- if (urb->actual_length != +- usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) { +- urb->status = -EREMOTEIO; +- } +- } +- } +- +- /* The driver will resubmit the URB so we need to remove it first */ +- etrax_usb_unlink_urb(urb, 0); +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- +- DBFEXIT; +-} +- +- +-static int etrax_usb_submit_isoc_urb(struct urb *urb) +-{ +- int epid; +- unsigned long flags; +- +- DBFENTER; +- +- dbg_isoc("Submitting isoc urb = 0x%lx", (unsigned long)urb); +- +- /* Epid allocation, empty check and list add must be protected. +- Read about this in etrax_usb_submit_ctrl_urb. */ +- +- spin_lock_irqsave(&urb_list_lock, flags); +- /* Is there an active epid for this urb ? */ +- epid = etrax_usb_setup_epid(urb); +- if (epid == -1) { +- DBFEXIT; +- spin_unlock_irqrestore(&urb_list_lock, flags); +- return -ENOMEM; +- } +- +- /* Ok, now we got valid endpoint, lets insert some traffic */ +- +- urb->status = -EINPROGRESS; +- +- /* Find the last urb in the URB_List and add this urb after that one. +- Also add the traffic, that is do an etrax_usb_add_to_isoc_sb_list. This +- is important to make this in "real time" since isochronous traffic is +- time sensitive. */ +- +- dbg_isoc("Adding isoc urb to (possibly empty) list"); +- urb_list_add(urb, epid); +- etrax_usb_add_to_isoc_sb_list(urb, epid); +- spin_unlock_irqrestore(&urb_list_lock, flags); +- +- DBFEXIT; +- +- return 0; +-} +- +-static void etrax_usb_check_error_isoc_ep(const int epid) +-{ +- unsigned long int flags; +- int error_code; +- __u32 r_usb_ept_data; +- +- /* We can't read R_USB_EPID_ATTN here since it would clear the iso_eof, +- bulk_eot and epid_attn interrupts. So we just check the status of +- the epid without testing if for it in R_USB_EPID_ATTN. */ +- +- +- save_flags(flags); +- cli(); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- /* Note that although there are separate R_USB_EPT_DATA and R_USB_EPT_DATA_ISO +- registers, they are located at the same address and are of the same size. +- In other words, this read should be ok for isoc also. */ +- r_usb_ept_data = *R_USB_EPT_DATA; +- restore_flags(flags); +- +- error_code = IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data); +- +- if (r_usb_ept_data & IO_MASK(R_USB_EPT_DATA, hold)) { +- warn("Hold was set for epid %d.", epid); +- return; +- } +- +- if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA_ISO, error_code, no_error)) { +- +- /* This indicates that the SB list of the ept was completed before +- new data was appended to it. This is not an error, but indicates +- large system or USB load and could possibly cause trouble for +- very timing sensitive USB device drivers so we log it. +- */ +- info("Isoc. epid %d disabled with no error", epid); +- return; +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA_ISO, error_code, stall)) { +- /* Not really a protocol error, just says that the endpoint gave +- a stall response. Note that error_code cannot be stall for isoc. */ +- panic("Isoc traffic cannot stall"); +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA_ISO, error_code, bus_error)) { +- /* Two devices responded to a transaction request. Must be resolved +- by software. FIXME: Reset ports? */ +- panic("Bus error for epid %d." +- " Two devices responded to transaction request", +- epid); +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, buffer_error)) { +- /* DMA overrun or underrun. */ +- warn("Buffer overrun/underrun for epid %d. DMA too busy?", epid); +- +- /* It seems that error_code = buffer_error in +- R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS +- are the same error. */ +- } +-} +- +- +-static void etrax_usb_add_to_isoc_sb_list(struct urb *urb, int epid) +-{ +- +- int i = 0; +- +- etrax_urb_priv_t *urb_priv; +- USB_SB_Desc_t *prev_sb_desc, *next_sb_desc, *temp_sb_desc; +- +- DBFENTER; +- +- prev_sb_desc = next_sb_desc = temp_sb_desc = NULL; +- +- urb_priv = kzalloc(sizeof(etrax_urb_priv_t), GFP_ATOMIC); +- assert(urb_priv != NULL); +- +- urb->hcpriv = urb_priv; +- urb_priv->epid = epid; +- +- if (usb_pipeout(urb->pipe)) { +- +- if (urb->number_of_packets == 0) panic("etrax_usb_add_to_isoc_sb_list 0 packets\n"); +- +- dbg_isoc("Transfer for epid %d is OUT", epid); +- dbg_isoc("%d packets in URB", urb->number_of_packets); +- +- /* Create one SB descriptor for each packet and link them together. */ +- for (i = 0; i < urb->number_of_packets; i++) { +- if (!urb->iso_frame_desc[i].length) +- continue; +- +- next_sb_desc = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_ATOMIC); +- assert(next_sb_desc != NULL); +- +- if (urb->iso_frame_desc[i].length > 0) { +- +- next_sb_desc->command = (IO_STATE(USB_SB_command, tt, out) | +- IO_STATE(USB_SB_command, eot, yes)); +- +- next_sb_desc->sw_len = urb->iso_frame_desc[i].length; +- next_sb_desc->buf = virt_to_phys((char*)urb->transfer_buffer + urb->iso_frame_desc[i].offset); +- +- /* Check if full length transfer. */ +- if (urb->iso_frame_desc[i].length == +- usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) { +- next_sb_desc->command |= IO_STATE(USB_SB_command, full, yes); +- } +- } else { +- dbg_isoc("zero len packet"); +- next_sb_desc->command = (IO_FIELD(USB_SB_command, rem, 0) | +- IO_STATE(USB_SB_command, tt, zout) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, full, yes)); +- +- next_sb_desc->sw_len = 1; +- next_sb_desc->buf = virt_to_phys(&zout_buffer[0]); +- } +- +- /* First SB descriptor that belongs to this urb */ +- if (i == 0) +- urb_priv->first_sb = next_sb_desc; +- else +- prev_sb_desc->next = virt_to_phys(next_sb_desc); +- +- prev_sb_desc = next_sb_desc; +- } +- +- next_sb_desc->command |= (IO_STATE(USB_SB_command, intr, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- next_sb_desc->next = 0; +- urb_priv->last_sb = next_sb_desc; +- +- } else if (usb_pipein(urb->pipe)) { +- +- dbg_isoc("Transfer for epid %d is IN", epid); +- dbg_isoc("transfer_buffer_length = %d", urb->transfer_buffer_length); +- dbg_isoc("rem is calculated to %d", urb->iso_frame_desc[urb->number_of_packets - 1].length); +- +- /* Note that in descriptors for periodic traffic are not consumed. This means that +- the USB controller never propagates in the SB list. In other words, if there already +- is an SB descriptor in the list for this EP we don't have to do anything. */ +- if (TxIsocEPList[epid].sub == 0) { +- dbg_isoc("Isoc traffic not already running, allocating SB"); +- +- next_sb_desc = (USB_SB_Desc_t*)kmem_cache_alloc(usb_desc_cache, SLAB_ATOMIC); +- assert(next_sb_desc != NULL); +- +- next_sb_desc->command = (IO_STATE(USB_SB_command, tt, in) | +- IO_STATE(USB_SB_command, eot, yes) | +- IO_STATE(USB_SB_command, eol, yes)); +- +- next_sb_desc->next = 0; +- next_sb_desc->sw_len = 1; /* Actual number of packets is not relevant +- for periodic in traffic as long as it is more +- than zero. Set to 1 always. */ +- next_sb_desc->buf = 0; +- +- /* The rem field is don't care for isoc traffic, so we don't set it. */ +- +- /* Only one SB descriptor that belongs to this urb. */ +- urb_priv->first_sb = next_sb_desc; +- urb_priv->last_sb = next_sb_desc; +- +- } else { +- +- dbg_isoc("Isoc traffic already running, just setting first/last_sb"); +- +- /* Each EP for isoc in will have only one SB descriptor, setup when submitting the +- already active urb. Note that even though we may have several first_sb/last_sb +- pointing at the same SB descriptor, they are freed only once (when the list has +- become empty). */ +- urb_priv->first_sb = phys_to_virt(TxIsocEPList[epid].sub); +- urb_priv->last_sb = phys_to_virt(TxIsocEPList[epid].sub); +- return; +- } +- +- } +- +- /* Find the spot to insert this urb and add it. */ +- if (TxIsocEPList[epid].sub == 0) { +- /* First SB descriptor inserted in this list (in or out). */ +- dbg_isoc("Inserting SB desc first in list"); +- TxIsocEPList[epid].hw_len = 0; +- TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); +- +- } else { +- /* Isochronous traffic is already running, insert new traffic last (only out). */ +- dbg_isoc("Inserting SB desc last in list"); +- temp_sb_desc = phys_to_virt(TxIsocEPList[epid].sub); +- while ((temp_sb_desc->command & IO_MASK(USB_SB_command, eol)) != +- IO_STATE(USB_SB_command, eol, yes)) { +- assert(temp_sb_desc->next); +- temp_sb_desc = phys_to_virt(temp_sb_desc->next); +- } +- dbg_isoc("Appending list on desc 0x%p", temp_sb_desc); +- +- /* Next pointer must be set before eol is removed. */ +- temp_sb_desc->next = virt_to_phys(urb_priv->first_sb); +- /* Clear the previous end of list flag since there is a new in the +- added SB descriptor list. */ +- temp_sb_desc->command &= ~IO_MASK(USB_SB_command, eol); +- +- if (!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { +- /* 8.8.5 in Designer's Reference says we should check for and correct +- any errors in the EP here. That should not be necessary if epid_attn +- is handled correctly, so we assume all is ok. */ +- dbg_isoc("EP disabled"); +- etrax_usb_check_error_isoc_ep(epid); +- +- /* The SB list was exhausted. */ +- if (virt_to_phys(urb_priv->last_sb) != TxIsocEPList[epid].sub) { +- /* The new sublist did not get processed before the EP was +- disabled. Setup the EP again. */ +- dbg_isoc("Set EP sub to new list"); +- TxIsocEPList[epid].hw_len = 0; +- TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); +- } +- } +- } +- +- if (urb->transfer_flags & URB_ISO_ASAP) { +- /* The isoc transfer should be started as soon as possible. The start_frame +- field is a return value if URB_ISO_ASAP was set. Comparing R_USB_FM_NUMBER +- with a USB Chief trace shows that the first isoc IN token is sent 2 frames +- later. I'm not sure how this affects usage of the start_frame field by the +- device driver, or how it affects things when USB_ISO_ASAP is not set, so +- therefore there's no compensation for the 2 frame "lag" here. */ +- urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff); +- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- urb_priv->urb_state = STARTED; +- dbg_isoc("URB_ISO_ASAP set, urb->start_frame set to %d", urb->start_frame); +- } else { +- /* Not started yet. */ +- urb_priv->urb_state = NOT_STARTED; +- dbg_isoc("urb_priv->urb_state set to NOT_STARTED"); +- } +- +- /* We start the DMA sub channel without checking if it's running or not, because: +- 1) If it's already running, issuing the start command is a nop. +- 2) We avoid a test-and-set race condition. */ +- *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); +- +- DBFEXIT; +-} +- +-static void etrax_usb_complete_isoc_urb(struct urb *urb, int status) +-{ +- etrax_urb_priv_t *urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- int epid = urb_priv->epid; +- int auto_resubmit = 0; +- +- DBFENTER; +- dbg_isoc("complete urb 0x%p, status %d", urb, status); +- +- if (status) +- warn("Completing isoc urb with status %d.", status); +- +- if (usb_pipein(urb->pipe)) { +- int i; +- +- /* Make that all isoc packets have status and length set before +- completing the urb. */ +- for (i = urb_priv->isoc_packet_counter; i < urb->number_of_packets; i++) { +- urb->iso_frame_desc[i].actual_length = 0; +- urb->iso_frame_desc[i].status = -EPROTO; +- } +- +- urb_list_del(urb, epid); +- +- if (!list_empty(&urb_list[epid])) { +- ((etrax_urb_priv_t *)(urb_list_first(epid)->hcpriv))->urb_state = STARTED; +- } else { +- unsigned long int flags; +- if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { +- /* The EP was enabled, disable it and wait. */ +- TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); +- +- /* Ah, the luxury of busy-wait. */ +- while (*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])); +- } +- +- etrax_remove_from_sb_list(urb); +- TxIsocEPList[epid].sub = 0; +- TxIsocEPList[epid].hw_len = 0; +- +- save_flags(flags); +- cli(); +- etrax_usb_free_epid(epid); +- restore_flags(flags); +- } +- +- urb->hcpriv = 0; +- kfree(urb_priv); +- +- /* Release allocated bandwidth. */ +- usb_release_bandwidth(urb->dev, urb, 0); +- } else if (usb_pipeout(urb->pipe)) { +- int freed_descr; +- +- dbg_isoc("Isoc out urb complete 0x%p", urb); +- +- /* Update the urb list. */ +- urb_list_del(urb, epid); +- +- freed_descr = etrax_remove_from_sb_list(urb); +- dbg_isoc("freed %d descriptors of %d packets", freed_descr, urb->number_of_packets); +- assert(freed_descr == urb->number_of_packets); +- urb->hcpriv = 0; +- kfree(urb_priv); +- +- /* Release allocated bandwidth. */ +- usb_release_bandwidth(urb->dev, urb, 0); +- } +- +- urb->status = status; +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- +- if (auto_resubmit) { +- /* Check that urb was not unlinked by the complete callback. */ +- if (__urb_list_entry(urb, epid)) { +- /* Move this one down the list. */ +- urb_list_move_last(urb, epid); +- +- /* Mark the now first urb as started (may already be). */ +- ((etrax_urb_priv_t *)(urb_list_first(epid)->hcpriv))->urb_state = STARTED; +- +- /* Must set this to 0 since this urb is still active after +- completion. */ +- urb_priv->isoc_packet_counter = 0; +- } else { +- warn("(ISOC) automatic resubmit urb 0x%p removed by complete.", urb); +- } +- } +- +- DBFEXIT; +-} +- +-static void etrax_usb_complete_urb(struct urb *urb, int status) +-{ +- switch (usb_pipetype(urb->pipe)) { +- case PIPE_BULK: +- etrax_usb_complete_bulk_urb(urb, status); +- break; +- case PIPE_CONTROL: +- etrax_usb_complete_ctrl_urb(urb, status); +- break; +- case PIPE_INTERRUPT: +- etrax_usb_complete_intr_urb(urb, status); +- break; +- case PIPE_ISOCHRONOUS: +- etrax_usb_complete_isoc_urb(urb, status); +- break; +- default: +- err("Unknown pipetype"); +- } +-} +- +- +- +-static irqreturn_t etrax_usb_hc_interrupt_top_half(int irq, void *vhc) +-{ +- usb_interrupt_registers_t *reg; +- unsigned long flags; +- __u32 irq_mask; +- __u8 status; +- __u32 epid_attn; +- __u16 port_status_1; +- __u16 port_status_2; +- __u32 fm_number; +- +- DBFENTER; +- +- /* Read critical registers into local variables, do kmalloc afterwards. */ +- save_flags(flags); +- cli(); +- +- irq_mask = *R_USB_IRQ_MASK_READ; +- /* Reading R_USB_STATUS clears the ctl_status interrupt. Note that R_USB_STATUS +- must be read before R_USB_EPID_ATTN since reading the latter clears the +- ourun and perror fields of R_USB_STATUS. */ +- status = *R_USB_STATUS; +- +- /* Reading R_USB_EPID_ATTN clears the iso_eof, bulk_eot and epid_attn interrupts. */ +- epid_attn = *R_USB_EPID_ATTN; +- +- /* Reading R_USB_RH_PORT_STATUS_1 and R_USB_RH_PORT_STATUS_2 clears the +- port_status interrupt. */ +- port_status_1 = *R_USB_RH_PORT_STATUS_1; +- port_status_2 = *R_USB_RH_PORT_STATUS_2; +- +- /* Reading R_USB_FM_NUMBER clears the sof interrupt. */ +- /* Note: the lower 11 bits contain the actual frame number, sent with each sof. */ +- fm_number = *R_USB_FM_NUMBER; +- +- restore_flags(flags); +- +- reg = (usb_interrupt_registers_t *)kmem_cache_alloc(top_half_reg_cache, SLAB_ATOMIC); +- +- assert(reg != NULL); +- +- reg->hc = (etrax_hc_t *)vhc; +- +- /* Now put register values into kmalloc'd area. */ +- reg->r_usb_irq_mask_read = irq_mask; +- reg->r_usb_status = status; +- reg->r_usb_epid_attn = epid_attn; +- reg->r_usb_rh_port_status_1 = port_status_1; +- reg->r_usb_rh_port_status_2 = port_status_2; +- reg->r_usb_fm_number = fm_number; +- +- INIT_WORK(®->usb_bh, etrax_usb_hc_interrupt_bottom_half, reg); +- schedule_work(®->usb_bh); +- +- DBFEXIT; +- +- return IRQ_HANDLED; +-} +- +-static void etrax_usb_hc_interrupt_bottom_half(void *data) +-{ +- usb_interrupt_registers_t *reg = (usb_interrupt_registers_t *)data; +- __u32 irq_mask = reg->r_usb_irq_mask_read; +- +- DBFENTER; +- +- /* Interrupts are handled in order of priority. */ +- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, epid_attn)) { +- etrax_usb_hc_epid_attn_interrupt(reg); +- } +- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, port_status)) { +- etrax_usb_hc_port_status_interrupt(reg); +- } +- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, ctl_status)) { +- etrax_usb_hc_ctl_status_interrupt(reg); +- } +- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, iso_eof)) { +- etrax_usb_hc_isoc_eof_interrupt(); +- } +- if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, bulk_eot)) { +- /* Update/restart the bulk start timer since obviously the channel is running. */ +- mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); +- /* Update/restart the bulk eot timer since we just received an bulk eot interrupt. */ +- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); +- +- etrax_usb_hc_bulk_eot_interrupt(0); +- } +- +- kmem_cache_free(top_half_reg_cache, reg); +- +- DBFEXIT; +-} +- +- +-void etrax_usb_hc_isoc_eof_interrupt(void) +-{ +- struct urb *urb; +- etrax_urb_priv_t *urb_priv; +- int epid; +- unsigned long flags; +- +- DBFENTER; +- +- /* Do not check the invalid epid (it has a valid sub pointer). */ +- for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { +- +- /* Do not check the invalid epid (it has a valid sub pointer). */ +- if ((epid == DUMMY_EPID) || (epid == INVALID_EPID)) +- continue; +- +- /* Disable interrupts to block the isoc out descriptor interrupt handler +- from being called while the isoc EPID list is being checked. +- */ +- save_flags(flags); +- cli(); +- +- if (TxIsocEPList[epid].sub == 0) { +- /* Nothing here to see. */ +- restore_flags(flags); +- continue; +- } +- +- /* Get the first urb (if any). */ +- urb = urb_list_first(epid); +- if (urb == 0) { +- warn("Ignoring NULL urb"); +- restore_flags(flags); +- continue; +- } +- if (usb_pipein(urb->pipe)) { +- +- /* Sanity check. */ +- assert(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); +- +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- if (urb_priv->urb_state == NOT_STARTED) { +- +- /* If ASAP is not set and urb->start_frame is the current frame, +- start the transfer. */ +- if (!(urb->transfer_flags & URB_ISO_ASAP) && +- (urb->start_frame == (*R_USB_FM_NUMBER & 0x7ff))) { +- +- dbg_isoc("Enabling isoc IN EP descr for epid %d", epid); +- TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); +- +- /* This urb is now active. */ +- urb_priv->urb_state = STARTED; +- continue; +- } +- } +- } +- restore_flags(flags); +- } +- +- DBFEXIT; +- +-} +- +-void etrax_usb_hc_bulk_eot_interrupt(int timer_induced) +-{ +- int epid; +- +- /* The technique is to run one urb at a time, wait for the eot interrupt at which +- point the EP descriptor has been disabled. */ +- +- DBFENTER; +- dbg_bulk("bulk eot%s", timer_induced ? ", called by timer" : ""); +- +- for (epid = 0; epid < NBR_OF_EPIDS; epid++) { +- +- if (!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) && +- (TxBulkEPList[epid].sub != 0)) { +- +- struct urb *urb; +- etrax_urb_priv_t *urb_priv; +- unsigned long flags; +- __u32 r_usb_ept_data; +- +- /* Found a disabled EP descriptor which has a non-null sub pointer. +- Verify that this ctrl EP descriptor got disabled no errors. +- FIXME: Necessary to check error_code? */ +- dbg_bulk("for epid %d?", epid); +- +- /* Get the first urb. */ +- urb = urb_list_first(epid); +- +- /* FIXME: Could this happen for valid reasons? Why did it disappear? Because of +- wrong unlinking? */ +- if (!urb) { +- warn("NULL urb for epid %d", epid); +- continue; +- } +- +- assert(urb); +- urb_priv = (etrax_urb_priv_t *)urb->hcpriv; +- assert(urb_priv); +- +- /* Sanity checks. */ +- assert(usb_pipetype(urb->pipe) == PIPE_BULK); +- if (phys_to_virt(TxBulkEPList[epid].sub) != urb_priv->last_sb) { +- err("bulk endpoint got disabled before reaching last sb"); +- } +- +- /* For bulk IN traffic, there seems to be a race condition between +- between the bulk eot and eop interrupts, or rather an uncertainty regarding +- the order in which they happen. Normally we expect the eop interrupt from +- DMA channel 9 to happen before the eot interrupt. +- +- Therefore, we complete the bulk IN urb in the rx interrupt handler instead. */ +- +- if (usb_pipein(urb->pipe)) { +- dbg_bulk("in urb, continuing"); +- continue; +- } +- +- save_flags(flags); +- cli(); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- r_usb_ept_data = *R_USB_EPT_DATA; +- restore_flags(flags); +- +- if (IO_EXTRACT(R_USB_EPT_DATA, error_code, r_usb_ept_data) == +- IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { +- /* This means that the endpoint has no error, is disabled +- and had inserted traffic, i.e. transfer successfully completed. */ +- etrax_usb_complete_bulk_urb(urb, 0); +- } else { +- /* Shouldn't happen. We expect errors to be caught by epid attention. */ +- err("Found disabled bulk EP desc, error_code != no_error"); +- } +- } +- } +- +- /* Normally, we should find (at least) one disabled EP descriptor with a valid sub pointer. +- However, because of the uncertainty in the deliverance of the eop/eot interrupts, we may +- not. Also, we might find two disabled EPs when handling an eot interrupt, and then find +- none the next time. */ +- +- DBFEXIT; +- +-} +- +-void etrax_usb_hc_epid_attn_interrupt(usb_interrupt_registers_t *reg) +-{ +- /* This function handles the epid attention interrupt. There are a variety of reasons +- for this interrupt to happen (Designer's Reference, p. 8 - 22 for the details): +- +- invalid ep_id - Invalid epid in an EP (EP disabled). +- stall - Not strictly an error condition (EP disabled). +- 3rd error - Three successive transaction errors (EP disabled). +- buffer ourun - Buffer overrun or underrun (EP disabled). +- past eof1 - Intr or isoc transaction proceeds past EOF1. +- near eof - Intr or isoc transaction would not fit inside the frame. +- zout transfer - If zout transfer for a bulk endpoint (EP disabled). +- setup transfer - If setup transfer for a non-ctrl endpoint (EP disabled). */ +- +- int epid; +- +- +- DBFENTER; +- +- assert(reg != NULL); +- +- /* Note that we loop through all epids. We still want to catch errors for +- the invalid one, even though we might handle them differently. */ +- for (epid = 0; epid < NBR_OF_EPIDS; epid++) { +- +- if (test_bit(epid, (void *)®->r_usb_epid_attn)) { +- +- struct urb *urb; +- __u32 r_usb_ept_data; +- unsigned long flags; +- int error_code; +- +- save_flags(flags); +- cli(); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); +- nop(); +- /* Note that although there are separate R_USB_EPT_DATA and R_USB_EPT_DATA_ISO +- registers, they are located at the same address and are of the same size. +- In other words, this read should be ok for isoc also. */ +- r_usb_ept_data = *R_USB_EPT_DATA; +- restore_flags(flags); +- +- /* First some sanity checks. */ +- if (epid == INVALID_EPID) { +- /* FIXME: What if it became disabled? Could seriously hurt interrupt +- traffic. (Use do_intr_recover.) */ +- warn("Got epid_attn for INVALID_EPID (%d).", epid); +- err("R_USB_EPT_DATA = 0x%x", r_usb_ept_data); +- err("R_USB_STATUS = 0x%x", reg->r_usb_status); +- continue; +- } else if (epid == DUMMY_EPID) { +- /* We definitely don't care about these ones. Besides, they are +- always disabled, so any possible disabling caused by the +- epid attention interrupt is irrelevant. */ +- warn("Got epid_attn for DUMMY_EPID (%d).", epid); +- continue; +- } +- +- /* Get the first urb in the urb list for this epid. We blatantly assume +- that only the first urb could have caused the epid attention. +- (For bulk and ctrl, only one urb is active at any one time. For intr +- and isoc we remove them once they are completed.) */ +- urb = urb_list_first(epid); +- +- if (urb == NULL) { +- err("Got epid_attn for epid %i with no urb.", epid); +- err("R_USB_EPT_DATA = 0x%x", r_usb_ept_data); +- err("R_USB_STATUS = 0x%x", reg->r_usb_status); +- continue; +- } +- +- switch (usb_pipetype(urb->pipe)) { +- case PIPE_BULK: +- warn("Got epid attn for bulk endpoint, epid %d", epid); +- break; +- case PIPE_CONTROL: +- warn("Got epid attn for control endpoint, epid %d", epid); +- break; +- case PIPE_INTERRUPT: +- warn("Got epid attn for interrupt endpoint, epid %d", epid); +- break; +- case PIPE_ISOCHRONOUS: +- warn("Got epid attn for isochronous endpoint, epid %d", epid); +- break; +- } +- +- if (usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) { +- if (r_usb_ept_data & IO_MASK(R_USB_EPT_DATA, hold)) { +- warn("Hold was set for epid %d.", epid); +- continue; +- } +- } +- +- /* Even though error_code occupies bits 22 - 23 in both R_USB_EPT_DATA and +- R_USB_EPT_DATA_ISOC, we separate them here so we don't forget in other places. */ +- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- error_code = IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data); +- } else { +- error_code = IO_EXTRACT(R_USB_EPT_DATA, error_code, r_usb_ept_data); +- } +- +- /* Using IO_STATE_VALUE on R_USB_EPT_DATA should be ok for isoc also. */ +- if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { +- +- /* Isoc traffic doesn't have error_count_in/error_count_out. */ +- if ((usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) && +- (IO_EXTRACT(R_USB_EPT_DATA, error_count_in, r_usb_ept_data) == 3 || +- IO_EXTRACT(R_USB_EPT_DATA, error_count_out, r_usb_ept_data) == 3)) { +- /* 3rd error. */ +- warn("3rd error for epid %i", epid); +- etrax_usb_complete_urb(urb, -EPROTO); +- +- } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { +- +- warn("Perror for epid %d", epid); +- +- if (!(r_usb_ept_data & IO_MASK(R_USB_EPT_DATA, valid))) { +- /* invalid ep_id */ +- panic("Perror because of invalid epid." +- " Deconfigured too early?"); +- } else { +- /* past eof1, near eof, zout transfer, setup transfer */ +- +- /* Dump the urb and the relevant EP descriptor list. */ +- +- __dump_urb(urb); +- __dump_ept_data(epid); +- __dump_ep_list(usb_pipetype(urb->pipe)); +- +- panic("Something wrong with DMA descriptor contents." +- " Too much traffic inserted?"); +- } +- } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { +- /* buffer ourun */ +- panic("Buffer overrun/underrun for epid %d. DMA too busy?", epid); +- } +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, stall)) { +- /* Not really a protocol error, just says that the endpoint gave +- a stall response. Note that error_code cannot be stall for isoc. */ +- if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { +- panic("Isoc traffic cannot stall"); +- } +- +- warn("Stall for epid %d", epid); +- etrax_usb_complete_urb(urb, -EPIPE); +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, bus_error)) { +- /* Two devices responded to a transaction request. Must be resolved +- by software. FIXME: Reset ports? */ +- panic("Bus error for epid %d." +- " Two devices responded to transaction request", +- epid); +- +- } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, buffer_error)) { +- /* DMA overrun or underrun. */ +- warn("Buffer overrun/underrun for epid %d. DMA too busy?", epid); +- +- /* It seems that error_code = buffer_error in +- R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS +- are the same error. */ +- etrax_usb_complete_urb(urb, -EPROTO); +- } +- } +- } +- +- DBFEXIT; +- +-} +- +-void etrax_usb_bulk_start_timer_func(unsigned long dummy) +-{ +- +- /* We might enable an EP descriptor behind the current DMA position when it's about +- to decide that there are no more bulk traffic and it should stop the bulk channel. +- Therefore we periodically check if the bulk channel is stopped and there is an +- enabled bulk EP descriptor, in which case we start the bulk channel. */ +- dbg_bulk("bulk_start_timer timed out."); +- +- if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) { +- int epid; +- +- dbg_bulk("Bulk DMA channel not running."); +- +- for (epid = 0; epid < NBR_OF_EPIDS; epid++) { +- if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { +- dbg_bulk("Found enabled EP for epid %d, starting bulk channel.\n", +- epid); +- *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); +- +- /* Restart the bulk eot timer since we just started the bulk channel. */ +- mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); +- +- /* No need to search any further. */ +- break; +- } +- } +- } else { +- dbg_bulk("Bulk DMA channel running."); +- } +-} +- +-void etrax_usb_hc_port_status_interrupt(usb_interrupt_registers_t *reg) +-{ +- etrax_hc_t *hc = reg->hc; +- __u16 r_usb_rh_port_status_1 = reg->r_usb_rh_port_status_1; +- __u16 r_usb_rh_port_status_2 = reg->r_usb_rh_port_status_2; +- +- DBFENTER; +- +- /* The Etrax RH does not include a wPortChange register, so this has to be handled in software +- (by saving the old port status value for comparison when the port status interrupt happens). +- See section 11.16.2.6.2 in the USB 1.1 spec for details. */ +- +- dbg_rh("hc->rh.prev_wPortStatus_1 = 0x%x", hc->rh.prev_wPortStatus_1); +- dbg_rh("hc->rh.prev_wPortStatus_2 = 0x%x", hc->rh.prev_wPortStatus_2); +- dbg_rh("r_usb_rh_port_status_1 = 0x%x", r_usb_rh_port_status_1); +- dbg_rh("r_usb_rh_port_status_2 = 0x%x", r_usb_rh_port_status_2); +- +- /* C_PORT_CONNECTION is set on any transition. */ +- hc->rh.wPortChange_1 |= +- ((r_usb_rh_port_status_1 & (1 << RH_PORT_CONNECTION)) != +- (hc->rh.prev_wPortStatus_1 & (1 << RH_PORT_CONNECTION))) ? +- (1 << RH_PORT_CONNECTION) : 0; +- +- hc->rh.wPortChange_2 |= +- ((r_usb_rh_port_status_2 & (1 << RH_PORT_CONNECTION)) != +- (hc->rh.prev_wPortStatus_2 & (1 << RH_PORT_CONNECTION))) ? +- (1 << RH_PORT_CONNECTION) : 0; +- +- /* C_PORT_ENABLE is _only_ set on a one to zero transition, i.e. when +- the port is disabled, not when it's enabled. */ +- hc->rh.wPortChange_1 |= +- ((hc->rh.prev_wPortStatus_1 & (1 << RH_PORT_ENABLE)) +- && !(r_usb_rh_port_status_1 & (1 << RH_PORT_ENABLE))) ? +- (1 << RH_PORT_ENABLE) : 0; +- +- hc->rh.wPortChange_2 |= +- ((hc->rh.prev_wPortStatus_2 & (1 << RH_PORT_ENABLE)) +- && !(r_usb_rh_port_status_2 & (1 << RH_PORT_ENABLE))) ? +- (1 << RH_PORT_ENABLE) : 0; +- +- /* C_PORT_SUSPEND is set to one when the device has transitioned out +- of the suspended state, i.e. when suspend goes from one to zero. */ +- hc->rh.wPortChange_1 |= +- ((hc->rh.prev_wPortStatus_1 & (1 << RH_PORT_SUSPEND)) +- && !(r_usb_rh_port_status_1 & (1 << RH_PORT_SUSPEND))) ? +- (1 << RH_PORT_SUSPEND) : 0; +- +- hc->rh.wPortChange_2 |= +- ((hc->rh.prev_wPortStatus_2 & (1 << RH_PORT_SUSPEND)) +- && !(r_usb_rh_port_status_2 & (1 << RH_PORT_SUSPEND))) ? +- (1 << RH_PORT_SUSPEND) : 0; +- +- +- /* C_PORT_RESET is set when reset processing on this port is complete. */ +- hc->rh.wPortChange_1 |= +- ((hc->rh.prev_wPortStatus_1 & (1 << RH_PORT_RESET)) +- && !(r_usb_rh_port_status_1 & (1 << RH_PORT_RESET))) ? +- (1 << RH_PORT_RESET) : 0; +- +- hc->rh.wPortChange_2 |= +- ((hc->rh.prev_wPortStatus_2 & (1 << RH_PORT_RESET)) +- && !(r_usb_rh_port_status_2 & (1 << RH_PORT_RESET))) ? +- (1 << RH_PORT_RESET) : 0; +- +- /* Save the new values for next port status change. */ +- hc->rh.prev_wPortStatus_1 = r_usb_rh_port_status_1; +- hc->rh.prev_wPortStatus_2 = r_usb_rh_port_status_2; +- +- dbg_rh("hc->rh.wPortChange_1 set to 0x%x", hc->rh.wPortChange_1); +- dbg_rh("hc->rh.wPortChange_2 set to 0x%x", hc->rh.wPortChange_2); +- +- DBFEXIT; +- +-} +- +-void etrax_usb_hc_ctl_status_interrupt(usb_interrupt_registers_t *reg) +-{ +- DBFENTER; +- +- /* FIXME: What should we do if we get ourun or perror? Dump the EP and SB +- list for the corresponding epid? */ +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { +- panic("USB controller got ourun."); +- } +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { +- +- /* Before, etrax_usb_do_intr_recover was called on this epid if it was +- an interrupt pipe. I don't see how re-enabling all EP descriptors +- will help if there was a programming error. */ +- panic("USB controller got perror."); +- } +- +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, device_mode)) { +- /* We should never operate in device mode. */ +- panic("USB controller in device mode."); +- } +- +- /* These if-statements could probably be nested. */ +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, host_mode)) { +- info("USB controller in host mode."); +- } +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, started)) { +- info("USB controller started."); +- } +- if (reg->r_usb_status & IO_MASK(R_USB_STATUS, running)) { +- info("USB controller running."); +- } +- +- DBFEXIT; +- +-} +- +- +-static int etrax_rh_submit_urb(struct urb *urb) +-{ +- struct usb_device *usb_dev = urb->dev; +- etrax_hc_t *hc = usb_dev->bus->hcpriv; +- unsigned int pipe = urb->pipe; +- struct usb_ctrlrequest *cmd = (struct usb_ctrlrequest *) urb->setup_packet; +- void *data = urb->transfer_buffer; +- int leni = urb->transfer_buffer_length; +- int len = 0; +- int stat = 0; +- +- __u16 bmRType_bReq; +- __u16 wValue; +- __u16 wIndex; +- __u16 wLength; +- +- DBFENTER; +- +- /* FIXME: What is this interrupt urb that is sent to the root hub? */ +- if (usb_pipetype (pipe) == PIPE_INTERRUPT) { +- dbg_rh("Root-Hub submit IRQ: every %d ms", urb->interval); +- hc->rh.urb = urb; +- hc->rh.send = 1; +- /* FIXME: We could probably remove this line since it's done +- in etrax_rh_init_int_timer. (Don't remove it from +- etrax_rh_init_int_timer though.) */ +- hc->rh.interval = urb->interval; +- etrax_rh_init_int_timer(urb); +- DBFEXIT; +- +- return 0; +- } +- +- bmRType_bReq = cmd->bRequestType | (cmd->bRequest << 8); +- wValue = le16_to_cpu(cmd->wValue); +- wIndex = le16_to_cpu(cmd->wIndex); +- wLength = le16_to_cpu(cmd->wLength); +- +- dbg_rh("bmRType_bReq : 0x%04x (%d)", bmRType_bReq, bmRType_bReq); +- dbg_rh("wValue : 0x%04x (%d)", wValue, wValue); +- dbg_rh("wIndex : 0x%04x (%d)", wIndex, wIndex); +- dbg_rh("wLength : 0x%04x (%d)", wLength, wLength); +- +- switch (bmRType_bReq) { +- +- /* Request Destination: +- without flags: Device, +- RH_INTERFACE: interface, +- RH_ENDPOINT: endpoint, +- RH_CLASS means HUB here, +- RH_OTHER | RH_CLASS almost ever means HUB_PORT here +- */ +- +- case RH_GET_STATUS: +- *(__u16 *) data = cpu_to_le16 (1); +- OK (2); +- +- case RH_GET_STATUS | RH_INTERFACE: +- *(__u16 *) data = cpu_to_le16 (0); +- OK (2); +- +- case RH_GET_STATUS | RH_ENDPOINT: +- *(__u16 *) data = cpu_to_le16 (0); +- OK (2); +- +- case RH_GET_STATUS | RH_CLASS: +- *(__u32 *) data = cpu_to_le32 (0); +- OK (4); /* hub power ** */ +- +- case RH_GET_STATUS | RH_OTHER | RH_CLASS: +- if (wIndex == 1) { +- *((__u16*)data) = cpu_to_le16(hc->rh.prev_wPortStatus_1); +- *((__u16*)data + 1) = cpu_to_le16(hc->rh.wPortChange_1); +- } else if (wIndex == 2) { +- *((__u16*)data) = cpu_to_le16(hc->rh.prev_wPortStatus_2); +- *((__u16*)data + 1) = cpu_to_le16(hc->rh.wPortChange_2); +- } else { +- dbg_rh("RH_GET_STATUS whith invalid wIndex!"); +- OK(0); +- } +- +- OK(4); +- +- case RH_CLEAR_FEATURE | RH_ENDPOINT: +- switch (wValue) { +- case (RH_ENDPOINT_STALL): +- OK (0); +- } +- break; +- +- case RH_CLEAR_FEATURE | RH_CLASS: +- switch (wValue) { +- case (RH_C_HUB_OVER_CURRENT): +- OK (0); /* hub power over current ** */ +- } +- break; +- +- case RH_CLEAR_FEATURE | RH_OTHER | RH_CLASS: +- switch (wValue) { +- case (RH_PORT_ENABLE): +- if (wIndex == 1) { +- +- dbg_rh("trying to do disable port 1"); +- +- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes); +- +- while (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)); +- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no); +- dbg_rh("Port 1 is disabled"); +- +- } else if (wIndex == 2) { +- +- dbg_rh("trying to do disable port 2"); +- +- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes); +- +- while (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes)); +- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no); +- dbg_rh("Port 2 is disabled"); +- +- } else { +- dbg_rh("RH_CLEAR_FEATURE->RH_PORT_ENABLE " +- "with invalid wIndex == %d!", wIndex); +- } +- +- OK (0); +- case (RH_PORT_SUSPEND): +- /* Opposite to suspend should be resume, so we'll do a resume. */ +- /* FIXME: USB 1.1, 11.16.2.2 says: +- "Clearing the PORT_SUSPEND feature causes a host-initiated resume +- on the specified port. If the port is not in the Suspended state, +- the hub should treat this request as a functional no-operation." +- Shouldn't we check if the port is in a suspended state before +- resuming? */ +- +- /* Make sure the controller isn't busy. */ +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- if (wIndex == 1) { +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port1) | +- IO_STATE(R_USB_COMMAND, port_cmd, resume) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- } else if (wIndex == 2) { +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port2) | +- IO_STATE(R_USB_COMMAND, port_cmd, resume) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- } else { +- dbg_rh("RH_CLEAR_FEATURE->RH_PORT_SUSPEND " +- "with invalid wIndex == %d!", wIndex); +- } +- +- OK (0); +- case (RH_PORT_POWER): +- OK (0); /* port power ** */ +- case (RH_C_PORT_CONNECTION): +- if (wIndex == 1) { +- hc->rh.wPortChange_1 &= ~(1 << RH_PORT_CONNECTION); +- } else if (wIndex == 2) { +- hc->rh.wPortChange_2 &= ~(1 << RH_PORT_CONNECTION); +- } else { +- dbg_rh("RH_CLEAR_FEATURE->RH_C_PORT_CONNECTION " +- "with invalid wIndex == %d!", wIndex); +- } +- +- OK (0); +- case (RH_C_PORT_ENABLE): +- if (wIndex == 1) { +- hc->rh.wPortChange_1 &= ~(1 << RH_PORT_ENABLE); +- } else if (wIndex == 2) { +- hc->rh.wPortChange_2 &= ~(1 << RH_PORT_ENABLE); +- } else { +- dbg_rh("RH_CLEAR_FEATURE->RH_C_PORT_ENABLE " +- "with invalid wIndex == %d!", wIndex); +- } +- OK (0); +- case (RH_C_PORT_SUSPEND): +-/*** WR_RH_PORTSTAT(RH_PS_PSSC); */ +- OK (0); +- case (RH_C_PORT_OVER_CURRENT): +- OK (0); /* port power over current ** */ +- case (RH_C_PORT_RESET): +- if (wIndex == 1) { +- hc->rh.wPortChange_1 &= ~(1 << RH_PORT_RESET); +- } else if (wIndex == 2) { +- hc->rh.wPortChange_2 &= ~(1 << RH_PORT_RESET); +- } else { +- dbg_rh("RH_CLEAR_FEATURE->RH_C_PORT_RESET " +- "with invalid index == %d!", wIndex); +- } +- +- OK (0); +- +- } +- break; +- +- case RH_SET_FEATURE | RH_OTHER | RH_CLASS: +- switch (wValue) { +- case (RH_PORT_SUSPEND): +- +- /* Make sure the controller isn't busy. */ +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- if (wIndex == 1) { +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port1) | +- IO_STATE(R_USB_COMMAND, port_cmd, suspend) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- } else if (wIndex == 2) { +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port2) | +- IO_STATE(R_USB_COMMAND, port_cmd, suspend) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- } else { +- dbg_rh("RH_SET_FEATURE->RH_PORT_SUSPEND " +- "with invalid wIndex == %d!", wIndex); +- } +- +- OK (0); +- case (RH_PORT_RESET): +- if (wIndex == 1) { +- +- port_1_reset: +- dbg_rh("Doing reset of port 1"); +- +- /* Make sure the controller isn't busy. */ +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port1) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- +- /* We must wait at least 10 ms for the device to recover. +- 15 ms should be enough. */ +- udelay(15000); +- +- /* Wait for reset bit to go low (should be done by now). */ +- while (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, reset, yes)); +- +- /* If the port status is +- 1) connected and enabled then there is a device and everything is fine +- 2) neither connected nor enabled then there is no device, also fine +- 3) connected and not enabled then we try again +- (Yes, there are other port status combinations besides these.) */ +- +- if ((hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) && +- (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, no))) { +- dbg_rh("Connected device on port 1, but port not enabled?" +- " Trying reset again."); +- goto port_2_reset; +- } +- +- /* Diagnostic printouts. */ +- if ((hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, connected, no)) && +- (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, no))) { +- dbg_rh("No connected device on port 1"); +- } else if ((hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) && +- (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes))) { +- dbg_rh("Connected device on port 1, port 1 enabled"); +- } +- +- } else if (wIndex == 2) { +- +- port_2_reset: +- dbg_rh("Doing reset of port 2"); +- +- /* Make sure the controller isn't busy. */ +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- /* Issue the reset command. */ +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, port2) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, nop); +- +- /* We must wait at least 10 ms for the device to recover. +- 15 ms should be enough. */ +- udelay(15000); +- +- /* Wait for reset bit to go low (should be done by now). */ +- while (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, reset, yes)); +- +- /* If the port status is +- 1) connected and enabled then there is a device and everything is fine +- 2) neither connected nor enabled then there is no device, also fine +- 3) connected and not enabled then we try again +- (Yes, there are other port status combinations besides these.) */ +- +- if ((hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, connected, yes)) && +- (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, no))) { +- dbg_rh("Connected device on port 2, but port not enabled?" +- " Trying reset again."); +- goto port_2_reset; +- } +- +- /* Diagnostic printouts. */ +- if ((hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, connected, no)) && +- (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, no))) { +- dbg_rh("No connected device on port 2"); +- } else if ((hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, connected, yes)) && +- (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, yes))) { +- dbg_rh("Connected device on port 2, port 2 enabled"); +- } +- +- } else { +- dbg_rh("RH_SET_FEATURE->RH_PORT_RESET with invalid wIndex = %d", wIndex); +- } +- +- /* Make sure the controller isn't busy. */ +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- /* If all enabled ports were disabled the host controller goes down into +- started mode, so we need to bring it back into the running state. +- (This is safe even if it's already in the running state.) */ +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, nop) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); +- +- dbg_rh("...Done"); +- OK(0); +- +- case (RH_PORT_POWER): +- OK (0); /* port power ** */ +- case (RH_PORT_ENABLE): +- /* There is no port enable command in the host controller, so if the +- port is already enabled, we do nothing. If not, we reset the port +- (with an ugly goto). */ +- +- if (wIndex == 1) { +- if (hc->rh.prev_wPortStatus_1 & +- IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, no)) { +- goto port_1_reset; +- } +- } else if (wIndex == 2) { +- if (hc->rh.prev_wPortStatus_2 & +- IO_STATE(R_USB_RH_PORT_STATUS_2, enabled, no)) { +- goto port_2_reset; +- } +- } else { +- dbg_rh("RH_SET_FEATURE->RH_GET_STATUS with invalid wIndex = %d", wIndex); +- } +- OK (0); +- } +- break; +- +- case RH_SET_ADDRESS: +- hc->rh.devnum = wValue; +- dbg_rh("RH address set to: %d", hc->rh.devnum); +- OK (0); +- +- case RH_GET_DESCRIPTOR: +- switch ((wValue & 0xff00) >> 8) { +- case (0x01): /* device descriptor */ +- len = min_t(unsigned int, leni, min_t(unsigned int, sizeof (root_hub_dev_des), wLength)); +- memcpy (data, root_hub_dev_des, len); +- OK (len); +- case (0x02): /* configuration descriptor */ +- len = min_t(unsigned int, leni, min_t(unsigned int, sizeof (root_hub_config_des), wLength)); +- memcpy (data, root_hub_config_des, len); +- OK (len); +- case (0x03): /* string descriptors */ +- len = usb_root_hub_string (wValue & 0xff, +- 0xff, "ETRAX 100LX", +- data, wLength); +- if (len > 0) { +- OK(min(leni, len)); +- } else { +- stat = -EPIPE; +- } +- +- } +- break; +- +- case RH_GET_DESCRIPTOR | RH_CLASS: +- root_hub_hub_des[2] = hc->rh.numports; +- len = min_t(unsigned int, leni, min_t(unsigned int, sizeof (root_hub_hub_des), wLength)); +- memcpy (data, root_hub_hub_des, len); +- OK (len); +- +- case RH_GET_CONFIGURATION: +- *(__u8 *) data = 0x01; +- OK (1); +- +- case RH_SET_CONFIGURATION: +- OK (0); +- +- default: +- stat = -EPIPE; +- } +- +- urb->actual_length = len; +- urb->status = stat; +- urb->dev = NULL; +- if (urb->complete) { +- urb->complete(urb, NULL); +- } +- DBFEXIT; +- +- return 0; +-} +- +-static void +-etrax_usb_bulk_eot_timer_func(unsigned long dummy) +-{ +- /* Because of a race condition in the top half, we might miss a bulk eot. +- This timer "simulates" a bulk eot if we don't get one for a while, hopefully +- correcting the situation. */ +- dbg_bulk("bulk_eot_timer timed out."); +- etrax_usb_hc_bulk_eot_interrupt(1); +-} +- +-static void* +-etrax_usb_buffer_alloc(struct usb_bus* bus, size_t size, +- unsigned mem_flags, dma_addr_t *dma) +-{ +- return kmalloc(size, mem_flags); +-} +- +-static void +-etrax_usb_buffer_free(struct usb_bus *bus, size_t size, void *addr, dma_addr_t dma) +-{ +- kfree(addr); +-} +- +- +-static struct device fake_device; +- +-static int __init etrax_usb_hc_init(void) +-{ +- static etrax_hc_t *hc; +- struct usb_bus *bus; +- struct usb_device *usb_rh; +- int i; +- +- DBFENTER; +- +- info("ETRAX 100LX USB-HCD %s (c) 2001-2003 Axis Communications AB\n", usb_hcd_version); +- +- hc = kmalloc(sizeof(etrax_hc_t), GFP_KERNEL); +- assert(hc != NULL); +- +- /* We use kmem_cache_* to make sure that all DMA desc. are dword aligned */ +- /* Note that we specify sizeof(USB_EP_Desc_t) as the size, but also allocate +- SB descriptors from this cache. This is ok since sizeof(USB_EP_Desc_t) == +- sizeof(USB_SB_Desc_t). */ +- +- usb_desc_cache = kmem_cache_create("usb_desc_cache", sizeof(USB_EP_Desc_t), 0, +- SLAB_HWCACHE_ALIGN, 0, 0); +- assert(usb_desc_cache != NULL); +- +- top_half_reg_cache = kmem_cache_create("top_half_reg_cache", +- sizeof(usb_interrupt_registers_t), +- 0, SLAB_HWCACHE_ALIGN, 0, 0); +- assert(top_half_reg_cache != NULL); +- +- isoc_compl_cache = kmem_cache_create("isoc_compl_cache", +- sizeof(usb_isoc_complete_data_t), +- 0, SLAB_HWCACHE_ALIGN, 0, 0); +- assert(isoc_compl_cache != NULL); +- +- etrax_usb_bus = bus = usb_alloc_bus(&etrax_usb_device_operations); +- hc->bus = bus; +- bus->bus_name="ETRAX 100LX"; +- bus->hcpriv = hc; +- +- /* Initialize RH to the default address. +- And make sure that we have no status change indication */ +- hc->rh.numports = 2; /* The RH has two ports */ +- hc->rh.devnum = 1; +- hc->rh.wPortChange_1 = 0; +- hc->rh.wPortChange_2 = 0; +- +- /* Also initate the previous values to zero */ +- hc->rh.prev_wPortStatus_1 = 0; +- hc->rh.prev_wPortStatus_2 = 0; +- +- /* Initialize the intr-traffic flags */ +- /* FIXME: This isn't used. (Besides, the error field isn't initialized.) */ +- hc->intr.sleeping = 0; +- hc->intr.wq = NULL; +- +- epid_usage_bitmask = 0; +- epid_out_traffic = 0; +- +- /* Mark the invalid epid as being used. */ +- set_bit(INVALID_EPID, (void *)&epid_usage_bitmask); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, INVALID_EPID); +- nop(); +- /* The valid bit should still be set ('invalid' is in our world; not the hardware's). */ +- *R_USB_EPT_DATA = (IO_STATE(R_USB_EPT_DATA, valid, yes) | +- IO_FIELD(R_USB_EPT_DATA, max_len, 1)); +- +- /* Mark the dummy epid as being used. */ +- set_bit(DUMMY_EPID, (void *)&epid_usage_bitmask); +- *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, DUMMY_EPID); +- nop(); +- *R_USB_EPT_DATA = (IO_STATE(R_USB_EPT_DATA, valid, no) | +- IO_FIELD(R_USB_EPT_DATA, max_len, 1)); +- +- /* Initialize the urb list by initiating a head for each list. */ +- for (i = 0; i < NBR_OF_EPIDS; i++) { +- INIT_LIST_HEAD(&urb_list[i]); +- } +- spin_lock_init(&urb_list_lock); +- +- INIT_LIST_HEAD(&urb_unlink_list); +- +- +- /* Initiate the bulk start timer. */ +- init_timer(&bulk_start_timer); +- bulk_start_timer.expires = jiffies + BULK_START_TIMER_INTERVAL; +- bulk_start_timer.function = etrax_usb_bulk_start_timer_func; +- add_timer(&bulk_start_timer); +- +- +- /* Initiate the bulk eot timer. */ +- init_timer(&bulk_eot_timer); +- bulk_eot_timer.expires = jiffies + BULK_EOT_TIMER_INTERVAL; +- bulk_eot_timer.function = etrax_usb_bulk_eot_timer_func; +- add_timer(&bulk_eot_timer); +- +- /* Set up the data structures for USB traffic. Note that this must be done before +- any interrupt that relies on sane DMA list occurrs. */ +- init_rx_buffers(); +- init_tx_bulk_ep(); +- init_tx_ctrl_ep(); +- init_tx_intr_ep(); +- init_tx_isoc_ep(); +- +- device_initialize(&fake_device); +- kobject_set_name(&fake_device.kobj, "etrax_usb"); +- kobject_add(&fake_device.kobj); +- kobject_uevent(&fake_device.kobj, KOBJ_ADD); +- hc->bus->controller = &fake_device; +- usb_register_bus(hc->bus); +- +- *R_IRQ_MASK2_SET = +- /* Note that these interrupts are not used. */ +- IO_STATE(R_IRQ_MASK2_SET, dma8_sub0_descr, set) | +- /* Sub channel 1 (ctrl) descr. interrupts are used. */ +- IO_STATE(R_IRQ_MASK2_SET, dma8_sub1_descr, set) | +- IO_STATE(R_IRQ_MASK2_SET, dma8_sub2_descr, set) | +- /* Sub channel 3 (isoc) descr. interrupts are used. */ +- IO_STATE(R_IRQ_MASK2_SET, dma8_sub3_descr, set); +- +- /* Note that the dma9_descr interrupt is not used. */ +- *R_IRQ_MASK2_SET = +- IO_STATE(R_IRQ_MASK2_SET, dma9_eop, set) | +- IO_STATE(R_IRQ_MASK2_SET, dma9_descr, set); +- +- /* FIXME: Enable iso_eof only when isoc traffic is running. */ +- *R_USB_IRQ_MASK_SET = +- IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set) | +- IO_STATE(R_USB_IRQ_MASK_SET, bulk_eot, set) | +- IO_STATE(R_USB_IRQ_MASK_SET, epid_attn, set) | +- IO_STATE(R_USB_IRQ_MASK_SET, port_status, set) | +- IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set); +- +- +- if (request_irq(ETRAX_USB_HC_IRQ, etrax_usb_hc_interrupt_top_half, 0, +- "ETRAX 100LX built-in USB (HC)", hc)) { +- err("Could not allocate IRQ %d for USB", ETRAX_USB_HC_IRQ); +- etrax_usb_hc_cleanup(); +- DBFEXIT; +- return -1; +- } +- +- if (request_irq(ETRAX_USB_RX_IRQ, etrax_usb_rx_interrupt, 0, +- "ETRAX 100LX built-in USB (Rx)", hc)) { +- err("Could not allocate IRQ %d for USB", ETRAX_USB_RX_IRQ); +- etrax_usb_hc_cleanup(); +- DBFEXIT; +- return -1; +- } +- +- if (request_irq(ETRAX_USB_TX_IRQ, etrax_usb_tx_interrupt, 0, +- "ETRAX 100LX built-in USB (Tx)", hc)) { +- err("Could not allocate IRQ %d for USB", ETRAX_USB_TX_IRQ); +- etrax_usb_hc_cleanup(); +- DBFEXIT; +- return -1; +- } +- +- /* R_USB_COMMAND: +- USB commands in host mode. The fields in this register should all be +- written to in one write. Do not read-modify-write one field at a time. A +- write to this register will trigger events in the USB controller and an +- incomplete command may lead to unpredictable results, and in worst case +- even to a deadlock in the controller. +- (Note however that the busy field is read-only, so no need to write to it.) */ +- +- /* Check the busy bit before writing to R_USB_COMMAND. */ +- +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- /* Reset the USB interface. */ +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, nop) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, reset); +- +- /* Designer's Reference, p. 8 - 10 says we should Initate R_USB_FM_PSTART to 0x2A30 (10800), +- to guarantee that control traffic gets 10% of the bandwidth, and periodic transfer may +- allocate the rest (90%). This doesn't work though. Read on for a lenghty explanation. +- +- While there is a difference between rev. 2 and rev. 3 of the ETRAX 100LX regarding the NAK +- behaviour, it doesn't solve this problem. What happens is that a control transfer will not +- be interrupted in its data stage when PSTART happens (the point at which periodic traffic +- is started). Thus, if PSTART is set to 10800 and its IN or OUT token is NAKed until just before +- PSTART happens, it will continue the IN/OUT transfer as long as it's ACKed. After it's done, +- there may be too little time left for an isochronous transfer, causing an epid attention +- interrupt due to perror. The work-around for this is to let the control transfers run at the +- end of the frame instead of at the beginning, and will be interrupted just fine if it doesn't +- fit into the frame. However, since there will *always* be a control transfer at the beginning +- of the frame, regardless of what we set PSTART to, that transfer might be a 64-byte transfer +- which consumes up to 15% of the frame, leaving only 85% for periodic traffic. The solution to +- this would be to 'dummy allocate' 5% of the frame with the usb_claim_bandwidth function to make +- sure that the periodic transfers that are inserted will always fit in the frame. +- +- The idea was suggested that a control transfer could be split up into several 8 byte transfers, +- so that it would be interrupted by PSTART, but since this can't be done for an IN transfer this +- hasn't been implemented. +- +- The value 11960 is chosen to be just after the SOF token, with a couple of bit times extra +- for possible bit stuffing. */ +- +- *R_USB_FM_PSTART = IO_FIELD(R_USB_FM_PSTART, value, 11960); +- +-#ifdef CONFIG_ETRAX_USB_HOST_PORT1 +- *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no); +-#endif +- +-#ifdef CONFIG_ETRAX_USB_HOST_PORT2 +- *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no); +-#endif +- +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- /* Configure the USB interface as a host controller. */ +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, nop) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_config); +- +- /* Note: Do not reset any ports here. Await the port status interrupts, to have a controlled +- sequence of resetting the ports. If we reset both ports now, and there are devices +- on both ports, we will get a bus error because both devices will answer the set address +- request. */ +- +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- /* Start processing of USB traffic. */ +- *R_USB_COMMAND = +- IO_STATE(R_USB_COMMAND, port_sel, nop) | +- IO_STATE(R_USB_COMMAND, port_cmd, reset) | +- IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); +- +- while (*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)); +- +- usb_rh = usb_alloc_dev(NULL, hc->bus, 0); +- hc->bus->root_hub = usb_rh; +- usb_rh->state = USB_STATE_ADDRESS; +- usb_rh->speed = USB_SPEED_FULL; +- usb_rh->devnum = 1; +- hc->bus->devnum_next = 2; +- usb_rh->ep0.desc.wMaxPacketSize = __const_cpu_to_le16(64); +- usb_get_device_descriptor(usb_rh, USB_DT_DEVICE_SIZE); +- usb_new_device(usb_rh); +- +- DBFEXIT; +- +- return 0; +-} +- +-static void etrax_usb_hc_cleanup(void) +-{ +- DBFENTER; +- +- free_irq(ETRAX_USB_HC_IRQ, NULL); +- free_irq(ETRAX_USB_RX_IRQ, NULL); +- free_irq(ETRAX_USB_TX_IRQ, NULL); +- +- usb_deregister_bus(etrax_usb_bus); +- +- /* FIXME: call kmem_cache_destroy here? */ +- +- DBFEXIT; +-} + +-module_init(etrax_usb_hc_init); +-module_exit(etrax_usb_hc_cleanup); ++/* Module hooks */ ++module_init(module_hcd_init); ++module_exit(module_hcd_exit); +--- linux-2.6.19.2.orig/drivers/usb/host/hc-crisv10.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/usb/host/hc-crisv10.c 2007-02-26 20:58:29.000000000 +0100 +@@ -0,0 +1,4684 @@ ++/* ++ * ++ * ETRAX 100LX USB Host Controller Driver ++ * ++ * Copyright (C) 2005, 2006 Axis Communications AB ++ * ++ * Author: Konrad Eriksson <konrad.eriksson@axis.se> ++ * ++ */ ++ ++#include <linux/module.h> ++#include <linux/kernel.h> ++#include <linux/init.h> ++#include <linux/moduleparam.h> ++#include <linux/spinlock.h> ++#include <linux/usb.h> ++#include <linux/platform_device.h> ++ ++#include <asm/io.h> ++#include <asm/irq.h> ++#include <asm/arch/dma.h> ++#include <asm/arch/io_interface_mux.h> ++ ++#include "../core/hcd.h" ++#include "../core/hub.h" ++#include "hc-crisv10.h" ++#include "hc-cris-dbg.h" ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Host Controller settings */ ++/***************************************************************************/ ++/***************************************************************************/ ++ ++#define VERSION "1.00" ++#define COPYRIGHT "(c) 2005, 2006 Axis Communications AB" ++#define DESCRIPTION "ETRAX 100LX USB Host Controller" ++ ++#define ETRAX_USB_HC_IRQ USB_HC_IRQ_NBR ++#define ETRAX_USB_RX_IRQ USB_DMA_RX_IRQ_NBR ++#define ETRAX_USB_TX_IRQ USB_DMA_TX_IRQ_NBR ++ ++/* Number of physical ports in Etrax 100LX */ ++#define USB_ROOT_HUB_PORTS 2 ++ ++const char hc_name[] = "hc-crisv10"; ++const char product_desc[] = DESCRIPTION; ++ ++/* The number of epids is, among other things, used for pre-allocating ++ ctrl, bulk and isoc EP descriptors (one for each epid). ++ Assumed to be > 1 when initiating the DMA lists. */ ++#define NBR_OF_EPIDS 32 ++ ++/* Support interrupt traffic intervals up to 128 ms. */ ++#define MAX_INTR_INTERVAL 128 ++ ++/* If periodic traffic (intr or isoc) is to be used, then one entry in the EP ++ table must be "invalid". By this we mean that we shouldn't care about epid ++ attentions for this epid, or at least handle them differently from epid ++ attentions for "valid" epids. This define determines which one to use ++ (don't change it). */ ++#define INVALID_EPID 31 ++/* A special epid for the bulk dummys. */ ++#define DUMMY_EPID 30 ++ ++/* Module settings */ ++ ++MODULE_DESCRIPTION(DESCRIPTION); ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Konrad Eriksson <konrad.eriksson@axis.se>"); ++ ++ ++/* Module parameters */ ++ ++/* 0 = No ports enabled ++ 1 = Only port 1 enabled (on board ethernet on devboard) ++ 2 = Only port 2 enabled (external connector on devboard) ++ 3 = Both ports enabled ++*/ ++static unsigned int ports = 3; ++module_param(ports, uint, S_IRUGO); ++MODULE_PARM_DESC(ports, "Bitmask indicating USB ports to use"); ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Shared global variables for this module */ ++/***************************************************************************/ ++/***************************************************************************/ ++ ++/* EP descriptor lists for non period transfers. Must be 32-bit aligned. */ ++static volatile struct USB_EP_Desc TxBulkEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); ++ ++static volatile struct USB_EP_Desc TxCtrlEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); ++ ++/* EP descriptor lists for period transfers. Must be 32-bit aligned. */ ++static volatile struct USB_EP_Desc TxIntrEPList[MAX_INTR_INTERVAL] __attribute__ ((aligned (4))); ++static volatile struct USB_SB_Desc TxIntrSB_zout __attribute__ ((aligned (4))); ++ ++static volatile struct USB_EP_Desc TxIsocEPList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); ++static volatile struct USB_SB_Desc TxIsocSB_zout __attribute__ ((aligned (4))); ++ ++static volatile struct USB_SB_Desc TxIsocSBList[NBR_OF_EPIDS] __attribute__ ((aligned (4))); ++ ++/* After each enabled bulk EP IN we put two disabled EP descriptors with the eol flag set, ++ causing the DMA to stop the DMA channel. The first of these two has the intr flag set, which ++ gives us a dma8_sub0_descr interrupt. When we receive this, we advance the DMA one step in the ++ EP list and then restart the bulk channel, thus forcing a switch between bulk EP descriptors ++ in each frame. */ ++static volatile struct USB_EP_Desc TxBulkDummyEPList[NBR_OF_EPIDS][2] __attribute__ ((aligned (4))); ++ ++/* List of URB pointers, where each points to the active URB for a epid. ++ For Bulk, Ctrl and Intr this means which URB that currently is added to ++ DMA lists (Isoc URBs are all directly added to DMA lists). As soon as ++ URB has completed is the queue examined and the first URB in queue is ++ removed and moved to the activeUrbList while its state change to STARTED and ++ its transfer(s) gets added to DMA list (exception Isoc where URBs enter ++ state STARTED directly and added transfers added to DMA lists). */ ++static struct urb *activeUrbList[NBR_OF_EPIDS]; ++ ++/* Additional software state info for each epid */ ++static struct etrax_epid epid_state[NBR_OF_EPIDS]; ++ ++/* Timer handles for bulk traffic timer used to avoid DMA bug where DMA stops ++ even if there is new data waiting to be processed */ ++static struct timer_list bulk_start_timer = TIMER_INITIALIZER(NULL, 0, 0); ++static struct timer_list bulk_eot_timer = TIMER_INITIALIZER(NULL, 0, 0); ++ ++/* We want the start timer to expire before the eot timer, because the former ++ might start traffic, thus making it unnecessary for the latter to time ++ out. */ ++#define BULK_START_TIMER_INTERVAL (HZ/50) /* 20 ms */ ++#define BULK_EOT_TIMER_INTERVAL (HZ/16) /* 60 ms */ ++ ++/* Delay before a URB completion happen when it's scheduled to be delayed */ ++#define LATER_TIMER_DELAY (HZ/50) /* 20 ms */ ++ ++/* Simplifying macros for checking software state info of a epid */ ++/* ----------------------------------------------------------------------- */ ++#define epid_inuse(epid) epid_state[epid].inuse ++#define epid_out_traffic(epid) epid_state[epid].out_traffic ++#define epid_isoc(epid) (epid_state[epid].type == PIPE_ISOCHRONOUS ? 1 : 0) ++#define epid_intr(epid) (epid_state[epid].type == PIPE_INTERRUPT ? 1 : 0) ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* DEBUG FUNCTIONS */ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Note that these functions are always available in their "__" variants, ++ for use in error situations. The "__" missing variants are controlled by ++ the USB_DEBUG_DESC/USB_DEBUG_URB macros. */ ++static void __dump_urb(struct urb* purb) ++{ ++ struct crisv10_urb_priv *urb_priv = purb->hcpriv; ++ int urb_num = -1; ++ if(urb_priv) { ++ urb_num = urb_priv->urb_num; ++ } ++ printk("\nURB:0x%x[%d]\n", (unsigned int)purb, urb_num); ++ printk("dev :0x%08lx\n", (unsigned long)purb->dev); ++ printk("pipe :0x%08x\n", purb->pipe); ++ printk("status :%d\n", purb->status); ++ printk("transfer_flags :0x%08x\n", purb->transfer_flags); ++ printk("transfer_buffer :0x%08lx\n", (unsigned long)purb->transfer_buffer); ++ printk("transfer_buffer_length:%d\n", purb->transfer_buffer_length); ++ printk("actual_length :%d\n", purb->actual_length); ++ printk("setup_packet :0x%08lx\n", (unsigned long)purb->setup_packet); ++ printk("start_frame :%d\n", purb->start_frame); ++ printk("number_of_packets :%d\n", purb->number_of_packets); ++ printk("interval :%d\n", purb->interval); ++ printk("error_count :%d\n", purb->error_count); ++ printk("context :0x%08lx\n", (unsigned long)purb->context); ++ printk("complete :0x%08lx\n\n", (unsigned long)purb->complete); ++} ++ ++static void __dump_in_desc(volatile struct USB_IN_Desc *in) ++{ ++ printk("\nUSB_IN_Desc at 0x%08lx\n", (unsigned long)in); ++ printk(" sw_len : 0x%04x (%d)\n", in->sw_len, in->sw_len); ++ printk(" command : 0x%04x\n", in->command); ++ printk(" next : 0x%08lx\n", in->next); ++ printk(" buf : 0x%08lx\n", in->buf); ++ printk(" hw_len : 0x%04x (%d)\n", in->hw_len, in->hw_len); ++ printk(" status : 0x%04x\n\n", in->status); ++} ++ ++static void __dump_sb_desc(volatile struct USB_SB_Desc *sb) ++{ ++ char tt = (sb->command & 0x30) >> 4; ++ char *tt_string; ++ ++ switch (tt) { ++ case 0: ++ tt_string = "zout"; ++ break; ++ case 1: ++ tt_string = "in"; ++ break; ++ case 2: ++ tt_string = "out"; ++ break; ++ case 3: ++ tt_string = "setup"; ++ break; ++ default: ++ tt_string = "unknown (weird)"; ++ } ++ ++ printk(" USB_SB_Desc at 0x%08lx ", (unsigned long)sb); ++ printk(" command:0x%04x (", sb->command); ++ printk("rem:%d ", (sb->command & 0x3f00) >> 8); ++ printk("full:%d ", (sb->command & 0x40) >> 6); ++ printk("tt:%d(%s) ", tt, tt_string); ++ printk("intr:%d ", (sb->command & 0x8) >> 3); ++ printk("eot:%d ", (sb->command & 0x2) >> 1); ++ printk("eol:%d)", sb->command & 0x1); ++ printk(" sw_len:0x%04x(%d)", sb->sw_len, sb->sw_len); ++ printk(" next:0x%08lx", sb->next); ++ printk(" buf:0x%08lx\n", sb->buf); ++} ++ ++ ++static void __dump_ep_desc(volatile struct USB_EP_Desc *ep) ++{ ++ printk("USB_EP_Desc at 0x%08lx ", (unsigned long)ep); ++ printk(" command:0x%04x (", ep->command); ++ printk("ep_id:%d ", (ep->command & 0x1f00) >> 8); ++ printk("enable:%d ", (ep->command & 0x10) >> 4); ++ printk("intr:%d ", (ep->command & 0x8) >> 3); ++ printk("eof:%d ", (ep->command & 0x2) >> 1); ++ printk("eol:%d)", ep->command & 0x1); ++ printk(" hw_len:0x%04x(%d)", ep->hw_len, ep->hw_len); ++ printk(" next:0x%08lx", ep->next); ++ printk(" sub:0x%08lx\n", ep->sub); ++} ++ ++static inline void __dump_ep_list(int pipe_type) ++{ ++ volatile struct USB_EP_Desc *ep; ++ volatile struct USB_EP_Desc *first_ep; ++ volatile struct USB_SB_Desc *sb; ++ ++ switch (pipe_type) ++ { ++ case PIPE_BULK: ++ first_ep = &TxBulkEPList[0]; ++ break; ++ case PIPE_CONTROL: ++ first_ep = &TxCtrlEPList[0]; ++ break; ++ case PIPE_INTERRUPT: ++ first_ep = &TxIntrEPList[0]; ++ break; ++ case PIPE_ISOCHRONOUS: ++ first_ep = &TxIsocEPList[0]; ++ break; ++ default: ++ warn("Cannot dump unknown traffic type"); ++ return; ++ } ++ ep = first_ep; ++ ++ printk("\n\nDumping EP list...\n\n"); ++ ++ do { ++ __dump_ep_desc(ep); ++ /* Cannot phys_to_virt on 0 as it turns into 80000000, which is != 0. */ ++ sb = ep->sub ? phys_to_virt(ep->sub) : 0; ++ while (sb) { ++ __dump_sb_desc(sb); ++ sb = sb->next ? phys_to_virt(sb->next) : 0; ++ } ++ ep = (volatile struct USB_EP_Desc *)(phys_to_virt(ep->next)); ++ ++ } while (ep != first_ep); ++} ++ ++static inline void __dump_ept_data(int epid) ++{ ++ unsigned long flags; ++ __u32 r_usb_ept_data; ++ ++ if (epid < 0 || epid > 31) { ++ printk("Cannot dump ept data for invalid epid %d\n", epid); ++ return; ++ } ++ ++ local_irq_save(flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ r_usb_ept_data = *R_USB_EPT_DATA; ++ local_irq_restore(flags); ++ ++ printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", r_usb_ept_data, epid); ++ if (r_usb_ept_data == 0) { ++ /* No need for more detailed printing. */ ++ return; ++ } ++ printk(" valid : %d\n", (r_usb_ept_data & 0x80000000) >> 31); ++ printk(" hold : %d\n", (r_usb_ept_data & 0x40000000) >> 30); ++ printk(" error_count_in : %d\n", (r_usb_ept_data & 0x30000000) >> 28); ++ printk(" t_in : %d\n", (r_usb_ept_data & 0x08000000) >> 27); ++ printk(" low_speed : %d\n", (r_usb_ept_data & 0x04000000) >> 26); ++ printk(" port : %d\n", (r_usb_ept_data & 0x03000000) >> 24); ++ printk(" error_code : %d\n", (r_usb_ept_data & 0x00c00000) >> 22); ++ printk(" t_out : %d\n", (r_usb_ept_data & 0x00200000) >> 21); ++ printk(" error_count_out : %d\n", (r_usb_ept_data & 0x00180000) >> 19); ++ printk(" max_len : %d\n", (r_usb_ept_data & 0x0003f800) >> 11); ++ printk(" ep : %d\n", (r_usb_ept_data & 0x00000780) >> 7); ++ printk(" dev : %d\n", (r_usb_ept_data & 0x0000003f)); ++} ++ ++static inline void __dump_ept_data_iso(int epid) ++{ ++ unsigned long flags; ++ __u32 ept_data; ++ ++ if (epid < 0 || epid > 31) { ++ printk("Cannot dump ept data for invalid epid %d\n", epid); ++ return; ++ } ++ ++ local_irq_save(flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ ept_data = *R_USB_EPT_DATA_ISO; ++ local_irq_restore(flags); ++ ++ printk(" R_USB_EPT_DATA = 0x%x for epid %d :\n", ept_data, epid); ++ if (ept_data == 0) { ++ /* No need for more detailed printing. */ ++ return; ++ } ++ printk(" valid : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, valid, ++ ept_data)); ++ printk(" port : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, port, ++ ept_data)); ++ printk(" error_code : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, ++ ept_data)); ++ printk(" max_len : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, max_len, ++ ept_data)); ++ printk(" ep : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, ep, ++ ept_data)); ++ printk(" dev : %d\n", IO_EXTRACT(R_USB_EPT_DATA_ISO, dev, ++ ept_data)); ++} ++ ++static inline void __dump_ept_data_list(void) ++{ ++ int i; ++ ++ printk("Dumping the whole R_USB_EPT_DATA list\n"); ++ ++ for (i = 0; i < 32; i++) { ++ __dump_ept_data(i); ++ } ++} ++ ++static void debug_epid(int epid) { ++ int i; ++ ++ if(epid_isoc(epid)) { ++ __dump_ept_data_iso(epid); ++ } else { ++ __dump_ept_data(epid); ++ } ++ ++ printk("Bulk:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxBulkEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxBulkEPList[i])); ++ } ++ } ++ ++ printk("Ctrl:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxCtrlEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxCtrlEPList[i])); ++ } ++ } ++ ++ printk("Intr:\n"); ++ for(i = 0; i < MAX_INTR_INTERVAL; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxIntrEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxIntrEPList[i])); ++ } ++ } ++ ++ printk("Isoc:\n"); ++ for(i = 0; i < 32; i++) { ++ if(IO_EXTRACT(USB_EP_command, epid, TxIsocEPList[i].command) == ++ epid) { ++ printk("%d: ", i); __dump_ep_desc(&(TxIsocEPList[i])); ++ } ++ } ++ ++ __dump_ept_data_list(); ++ __dump_ep_list(PIPE_INTERRUPT); ++ printk("\n\n"); ++} ++ ++ ++ ++char* hcd_status_to_str(__u8 bUsbStatus) { ++ static char hcd_status_str[128]; ++ hcd_status_str[0] = '\0'; ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, ourun, yes)) { ++ strcat(hcd_status_str, "ourun "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, perror, yes)) { ++ strcat(hcd_status_str, "perror "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, device_mode, yes)) { ++ strcat(hcd_status_str, "device_mode "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, host_mode, yes)) { ++ strcat(hcd_status_str, "host_mode "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, started, yes)) { ++ strcat(hcd_status_str, "started "); ++ } ++ if(bUsbStatus & IO_STATE(R_USB_STATUS, running, yes)) { ++ strcat(hcd_status_str, "running "); ++ } ++ return hcd_status_str; ++} ++ ++ ++char* sblist_to_str(struct USB_SB_Desc* sb_desc) { ++ static char sblist_to_str_buff[128]; ++ char tmp[32], tmp2[32]; ++ sblist_to_str_buff[0] = '\0'; ++ while(sb_desc != NULL) { ++ switch(IO_EXTRACT(USB_SB_command, tt, sb_desc->command)) { ++ case 0: sprintf(tmp, "zout"); break; ++ case 1: sprintf(tmp, "in"); break; ++ case 2: sprintf(tmp, "out"); break; ++ case 3: sprintf(tmp, "setup"); break; ++ } ++ sprintf(tmp2, "(%s %d)", tmp, sb_desc->sw_len); ++ strcat(sblist_to_str_buff, tmp2); ++ if(sb_desc->next != 0) { ++ sb_desc = phys_to_virt(sb_desc->next); ++ } else { ++ sb_desc = NULL; ++ } ++ } ++ return sblist_to_str_buff; ++} ++ ++char* port_status_to_str(__u16 wPortStatus) { ++ static char port_status_str[128]; ++ port_status_str[0] = '\0'; ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, connected, yes)) { ++ strcat(port_status_str, "connected "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) { ++ strcat(port_status_str, "enabled "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, suspended, yes)) { ++ strcat(port_status_str, "suspended "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, reset, yes)) { ++ strcat(port_status_str, "reset "); ++ } ++ if(wPortStatus & IO_STATE(R_USB_RH_PORT_STATUS_1, speed, full)) { ++ strcat(port_status_str, "full-speed "); ++ } else { ++ strcat(port_status_str, "low-speed "); ++ } ++ return port_status_str; ++} ++ ++ ++char* endpoint_to_str(struct usb_endpoint_descriptor *ed) { ++ static char endpoint_to_str_buff[128]; ++ char tmp[32]; ++ int epnum = ed->bEndpointAddress & 0x0F; ++ int dir = ed->bEndpointAddress & 0x80; ++ int type = ed->bmAttributes & 0x03; ++ endpoint_to_str_buff[0] = '\0'; ++ sprintf(endpoint_to_str_buff, "ep:%d ", epnum); ++ switch(type) { ++ case 0: ++ sprintf(tmp, " ctrl"); ++ break; ++ case 1: ++ sprintf(tmp, " isoc"); ++ break; ++ case 2: ++ sprintf(tmp, " bulk"); ++ break; ++ case 3: ++ sprintf(tmp, " intr"); ++ break; ++ } ++ strcat(endpoint_to_str_buff, tmp); ++ if(dir) { ++ sprintf(tmp, " in"); ++ } else { ++ sprintf(tmp, " out"); ++ } ++ strcat(endpoint_to_str_buff, tmp); ++ ++ return endpoint_to_str_buff; ++} ++ ++/* Debug helper functions for Transfer Controller */ ++char* pipe_to_str(unsigned int pipe) { ++ static char pipe_to_str_buff[128]; ++ char tmp[64]; ++ sprintf(pipe_to_str_buff, "dir:%s", str_dir(pipe)); ++ sprintf(tmp, " type:%s", str_type(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ ++ sprintf(tmp, " dev:%d", usb_pipedevice(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ sprintf(tmp, " ep:%d", usb_pipeendpoint(pipe)); ++ strcat(pipe_to_str_buff, tmp); ++ return pipe_to_str_buff; ++} ++ ++ ++#define USB_DEBUG_DESC 1 ++ ++#ifdef USB_DEBUG_DESC ++#define dump_in_desc(x) __dump_in_desc(x) ++#define dump_sb_desc(...) __dump_sb_desc(...) ++#define dump_ep_desc(x) __dump_ep_desc(x) ++#define dump_ept_data(x) __dump_ept_data(x) ++#else ++#define dump_in_desc(...) do {} while (0) ++#define dump_sb_desc(...) do {} while (0) ++#define dump_ep_desc(...) do {} while (0) ++#endif ++ ++ ++/* Uncomment this to enable massive function call trace ++ #define USB_DEBUG_TRACE */ ++ ++#ifdef USB_DEBUG_TRACE ++#define DBFENTER (printk(": Entering: %s\n", __FUNCTION__)) ++#define DBFEXIT (printk(": Exiting: %s\n", __FUNCTION__)) ++#else ++#define DBFENTER do {} while (0) ++#define DBFEXIT do {} while (0) ++#endif ++ ++#define CHECK_ALIGN(x) if (((__u32)(x)) & 0x00000003) \ ++{panic("Alignment check (DWORD) failed at %s:%s:%d\n", __FILE__, __FUNCTION__, __LINE__);} ++ ++/* Most helpful debugging aid */ ++#define ASSERT(expr) ((void) ((expr) ? 0 : (err("assert failed at: %s %d",__FUNCTION__, __LINE__)))) ++ ++ ++/***************************************************************************/ ++/***************************************************************************/ ++/* Forward declarations */ ++/***************************************************************************/ ++/***************************************************************************/ ++void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg); ++void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg); ++ ++void rh_port_status_change(__u16[]); ++int rh_clear_port_feature(__u8, __u16); ++int rh_set_port_feature(__u8, __u16); ++static void rh_disable_port(unsigned int port); ++ ++static void check_finished_bulk_tx_epids(struct usb_hcd *hcd, ++ int timer); ++ ++static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb, ++ int mem_flags); ++static void tc_free_epid(struct usb_host_endpoint *ep); ++static int tc_allocate_epid(void); ++static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status); ++static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb, ++ int status); ++ ++static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid, ++ int mem_flags); ++static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb); ++ ++static inline struct urb *urb_list_first(int epid); ++static inline void urb_list_add(struct urb *urb, int epid, ++ int mem_flags); ++static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid); ++static inline void urb_list_del(struct urb *urb, int epid); ++static inline void urb_list_move_last(struct urb *urb, int epid); ++static inline struct urb *urb_list_next(struct urb *urb, int epid); ++ ++int create_sb_for_urb(struct urb *urb, int mem_flags); ++int init_intr_urb(struct urb *urb, int mem_flags); ++ ++static inline void etrax_epid_set(__u8 index, __u32 data); ++static inline void etrax_epid_clear_error(__u8 index); ++static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout, ++ __u8 toggle); ++static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout); ++static inline __u32 etrax_epid_get(__u8 index); ++ ++/* We're accessing the same register position in Etrax so ++ when we do full access the internal difference doesn't matter */ ++#define etrax_epid_iso_set(index, data) etrax_epid_set(index, data) ++#define etrax_epid_iso_get(index) etrax_epid_get(index) ++ ++ ++static void tc_dma_process_isoc_urb(struct urb *urb); ++static void tc_dma_process_queue(int epid); ++static void tc_dma_unlink_intr_urb(struct urb *urb); ++static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc); ++static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc); ++ ++static void tc_bulk_start_timer_func(unsigned long dummy); ++static void tc_bulk_eot_timer_func(unsigned long dummy); ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Host Controler Driver block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* HCD operations */ ++static irqreturn_t crisv10_hcd_top_irq(int irq, void*); ++static int crisv10_hcd_reset(struct usb_hcd *); ++static int crisv10_hcd_start(struct usb_hcd *); ++static void crisv10_hcd_stop(struct usb_hcd *); ++#ifdef CONFIG_PM ++static int crisv10_hcd_suspend(struct device *, u32, u32); ++static int crisv10_hcd_resume(struct device *, u32); ++#endif /* CONFIG_PM */ ++static int crisv10_hcd_get_frame(struct usb_hcd *); ++ ++static int tc_urb_enqueue(struct usb_hcd *, struct usb_host_endpoint *ep, struct urb *, gfp_t mem_flags); ++static int tc_urb_dequeue(struct usb_hcd *, struct urb *); ++static void tc_endpoint_disable(struct usb_hcd *, struct usb_host_endpoint *ep); ++ ++static int rh_status_data_request(struct usb_hcd *, char *); ++static int rh_control_request(struct usb_hcd *, u16, u16, u16, char*, u16); ++ ++#ifdef CONFIG_PM ++static int crisv10_hcd_hub_suspend(struct usb_hcd *); ++static int crisv10_hcd_hub_resume(struct usb_hcd *); ++#endif /* CONFIG_PM */ ++#ifdef CONFIG_USB_OTG ++static int crisv10_hcd_start_port_reset(struct usb_hcd *, unsigned); ++#endif /* CONFIG_USB_OTG */ ++ ++/* host controller driver interface */ ++static const struct hc_driver crisv10_hc_driver = ++ { ++ .description = hc_name, ++ .product_desc = product_desc, ++ .hcd_priv_size = sizeof(struct crisv10_hcd), ++ ++ /* Attaching IRQ handler manualy in probe() */ ++ /* .irq = crisv10_hcd_irq, */ ++ ++ .flags = HCD_USB11, ++ ++ /* called to init HCD and root hub */ ++ .reset = crisv10_hcd_reset, ++ .start = crisv10_hcd_start, ++ ++ /* cleanly make HCD stop writing memory and doing I/O */ ++ .stop = crisv10_hcd_stop, ++ ++ /* return current frame number */ ++ .get_frame_number = crisv10_hcd_get_frame, ++ ++ ++ /* Manage i/o requests via the Transfer Controller */ ++ .urb_enqueue = tc_urb_enqueue, ++ .urb_dequeue = tc_urb_dequeue, ++ ++ /* hw synch, freeing endpoint resources that urb_dequeue can't */ ++ .endpoint_disable = tc_endpoint_disable, ++ ++ ++ /* Root Hub support */ ++ .hub_status_data = rh_status_data_request, ++ .hub_control = rh_control_request, ++#ifdef CONFIG_PM ++ .hub_suspend = rh_suspend_request, ++ .hub_resume = rh_resume_request, ++#endif /* CONFIG_PM */ ++#ifdef CONFIG_USB_OTG ++ .start_port_reset = crisv10_hcd_start_port_reset, ++#endif /* CONFIG_USB_OTG */ ++ }; ++ ++ ++/* ++ * conversion between pointers to a hcd and the corresponding ++ * crisv10_hcd ++ */ ++ ++static inline struct crisv10_hcd *hcd_to_crisv10_hcd(struct usb_hcd *hcd) ++{ ++ return (struct crisv10_hcd *) hcd->hcd_priv; ++} ++ ++static inline struct usb_hcd *crisv10_hcd_to_hcd(struct crisv10_hcd *hcd) ++{ ++ return container_of((void *) hcd, struct usb_hcd, hcd_priv); ++} ++ ++/* check if specified port is in use */ ++static inline int port_in_use(unsigned int port) ++{ ++ return ports & (1 << port); ++} ++ ++/* number of ports in use */ ++static inline unsigned int num_ports(void) ++{ ++ unsigned int i, num = 0; ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) ++ if (port_in_use(i)) ++ num++; ++ return num; ++} ++ ++/* map hub port number to the port number used internally by the HC */ ++static inline unsigned int map_port(unsigned int port) ++{ ++ unsigned int i, num = 0; ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) ++ if (port_in_use(i)) ++ if (++num == port) ++ return i; ++ return -1; ++} ++ ++/* size of descriptors in slab cache */ ++#ifndef MAX ++#define MAX(x, y) ((x) > (y) ? (x) : (y)) ++#endif ++ ++ ++/******************************************************************/ ++/* Hardware Interrupt functions */ ++/******************************************************************/ ++ ++/* Fast interrupt handler for HC */ ++static irqreturn_t crisv10_hcd_top_irq(int irq, void *vcd) ++{ ++ struct usb_hcd *hcd = vcd; ++ struct crisv10_irq_reg reg; ++ __u32 irq_mask; ++ unsigned long flags; ++ ++ DBFENTER; ++ ++ ASSERT(hcd != NULL); ++ reg.hcd = hcd; ++ ++ /* Turn of other interrupts while handling these sensitive cases */ ++ local_irq_save(flags); ++ ++ /* Read out which interrupts that are flaged */ ++ irq_mask = *R_USB_IRQ_MASK_READ; ++ reg.r_usb_irq_mask_read = irq_mask; ++ ++ /* Reading R_USB_STATUS clears the ctl_status interrupt. Note that ++ R_USB_STATUS must be read before R_USB_EPID_ATTN since reading the latter ++ clears the ourun and perror fields of R_USB_STATUS. */ ++ reg.r_usb_status = *R_USB_STATUS; ++ ++ /* Reading R_USB_EPID_ATTN clears the iso_eof, bulk_eot and epid_attn ++ interrupts. */ ++ reg.r_usb_epid_attn = *R_USB_EPID_ATTN; ++ ++ /* Reading R_USB_RH_PORT_STATUS_1 and R_USB_RH_PORT_STATUS_2 clears the ++ port_status interrupt. */ ++ reg.r_usb_rh_port_status_1 = *R_USB_RH_PORT_STATUS_1; ++ reg.r_usb_rh_port_status_2 = *R_USB_RH_PORT_STATUS_2; ++ ++ /* Reading R_USB_FM_NUMBER clears the sof interrupt. */ ++ /* Note: the lower 11 bits contain the actual frame number, sent with each ++ sof. */ ++ reg.r_usb_fm_number = *R_USB_FM_NUMBER; ++ ++ /* Interrupts are handled in order of priority. */ ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, port_status)) { ++ crisv10_hcd_port_status_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, epid_attn)) { ++ crisv10_hcd_epid_attn_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, ctl_status)) { ++ crisv10_hcd_ctl_status_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, iso_eof)) { ++ crisv10_hcd_isoc_eof_irq(®); ++ } ++ if (irq_mask & IO_MASK(R_USB_IRQ_MASK_READ, bulk_eot)) { ++ /* Update/restart the bulk start timer since obviously the channel is ++ running. */ ++ mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); ++ /* Update/restart the bulk eot timer since we just received an bulk eot ++ interrupt. */ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ ++ /* Check for finished bulk transfers on epids */ ++ check_finished_bulk_tx_epids(hcd, 0); ++ } ++ local_irq_restore(flags); ++ ++ DBFEXIT; ++ return IRQ_HANDLED; ++} ++ ++ ++void crisv10_hcd_epid_attn_irq(struct crisv10_irq_reg *reg) { ++ struct usb_hcd *hcd = reg->hcd; ++ struct crisv10_urb_priv *urb_priv; ++ int epid; ++ DBFENTER; ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (test_bit(epid, (void *)®->r_usb_epid_attn)) { ++ struct urb *urb; ++ __u32 ept_data; ++ int error_code; ++ ++ if (epid == DUMMY_EPID || epid == INVALID_EPID) { ++ /* We definitely don't care about these ones. Besides, they are ++ always disabled, so any possible disabling caused by the ++ epid attention interrupt is irrelevant. */ ++ warn("Got epid_attn for INVALID_EPID or DUMMY_EPID (%d).", epid); ++ continue; ++ } ++ ++ if(!epid_inuse(epid)) { ++ irq_err("Epid attention on epid:%d that isn't in use\n", epid); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ debug_epid(epid); ++ continue; ++ } ++ ++ /* Note that although there are separate R_USB_EPT_DATA and ++ R_USB_EPT_DATA_ISO registers, they are located at the same address and ++ are of the same size. In other words, this read should be ok for isoc ++ also. */ ++ ept_data = etrax_epid_get(epid); ++ error_code = IO_EXTRACT(R_USB_EPT_DATA, error_code, ept_data); ++ ++ /* Get the active URB for this epid. We blatantly assume ++ that only this URB could have caused the epid attention. */ ++ urb = activeUrbList[epid]; ++ if (urb == NULL) { ++ irq_err("Attention on epid:%d error:%d with no active URB.\n", ++ epid, error_code); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ debug_epid(epid); ++ continue; ++ } ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Using IO_STATE_VALUE on R_USB_EPT_DATA should be ok for isoc also. */ ++ if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ ++ /* Isoc traffic doesn't have error_count_in/error_count_out. */ ++ if ((usb_pipetype(urb->pipe) != PIPE_ISOCHRONOUS) && ++ (IO_EXTRACT(R_USB_EPT_DATA, error_count_in, ept_data) == 3 || ++ IO_EXTRACT(R_USB_EPT_DATA, error_count_out, ept_data) == 3)) { ++ /* Check if URB allready is marked for late-finish, we can get ++ several 3rd error for Intr traffic when a device is unplugged */ ++ if(urb_priv->later_data == NULL) { ++ /* 3rd error. */ ++ irq_warn("3rd error for epid:%d (%s %s) URB:0x%x[%d]\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe), ++ (unsigned int)urb, urb_priv->urb_num); ++ ++ tc_finish_urb_later(hcd, urb, -EPROTO); ++ } ++ ++ } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { ++ irq_warn("Perror for epid:%d\n", epid); ++ printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); ++ ++ if (!(ept_data & IO_MASK(R_USB_EPT_DATA, valid))) { ++ /* invalid ep_id */ ++ panic("Perror because of invalid epid." ++ " Deconfigured too early?"); ++ } else { ++ /* past eof1, near eof, zout transfer, setup transfer */ ++ /* Dump the urb and the relevant EP descriptor. */ ++ panic("Something wrong with DMA descriptor contents." ++ " Too much traffic inserted?"); ++ } ++ } else if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { ++ /* buffer ourun */ ++ printk("FM_NUMBER: %d\n", reg->r_usb_fm_number & 0x7ff); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); ++ ++ panic("Buffer overrun/underrun for epid:%d. DMA too busy?", epid); ++ } else { ++ irq_warn("Attention on epid:%d (%s %s) with no error code\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ printk("R_USB_STATUS: 0x%x\n", reg->r_usb_status); ++ __dump_urb(urb); ++ debug_epid(epid); ++ } ++ ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ stall)) { ++ /* Not really a protocol error, just says that the endpoint gave ++ a stall response. Note that error_code cannot be stall for isoc. */ ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ panic("Isoc traffic cannot stall"); ++ } ++ ++ tc_dbg("Stall for epid:%d (%s %s) URB:0x%x\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe), (unsigned int)urb); ++ tc_finish_urb(hcd, urb, -EPIPE); ++ ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ bus_error)) { ++ /* Two devices responded to a transaction request. Must be resolved ++ by software. FIXME: Reset ports? */ ++ panic("Bus error for epid %d." ++ " Two devices responded to transaction request\n", ++ epid); ++ ++ } else if (error_code == IO_STATE_VALUE(R_USB_EPT_DATA, error_code, ++ buffer_error)) { ++ /* DMA overrun or underrun. */ ++ irq_warn("Buffer overrun/underrun for epid:%d (%s %s)\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ ++ /* It seems that error_code = buffer_error in ++ R_USB_EPT_DATA/R_USB_EPT_DATA_ISO and ourun = yes in R_USB_STATUS ++ are the same error. */ ++ tc_finish_urb(hcd, urb, -EPROTO); ++ } else { ++ irq_warn("Unknown attention on epid:%d (%s %s)\n", epid, ++ str_dir(urb->pipe), str_type(urb->pipe)); ++ dump_ept_data(epid); ++ } ++ } ++ } ++ DBFEXIT; ++} ++ ++void crisv10_hcd_port_status_irq(struct crisv10_irq_reg *reg) ++{ ++ __u16 port_reg[USB_ROOT_HUB_PORTS]; ++ DBFENTER; ++ port_reg[0] = reg->r_usb_rh_port_status_1; ++ port_reg[1] = reg->r_usb_rh_port_status_2; ++ rh_port_status_change(port_reg); ++ DBFEXIT; ++} ++ ++void crisv10_hcd_isoc_eof_irq(struct crisv10_irq_reg *reg) ++{ ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv *urb_priv; ++ ++ DBFENTER; ++ ++ for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { ++ ++ /* Only check epids that are in use, is valid and has SB list */ ++ if (!epid_inuse(epid) || epid == INVALID_EPID || ++ TxIsocEPList[epid].sub == 0 || epid == DUMMY_EPID) { ++ /* Nothing here to see. */ ++ continue; ++ } ++ ASSERT(epid_isoc(epid)); ++ ++ /* Get the active URB for this epid (if any). */ ++ urb = activeUrbList[epid]; ++ if (urb == 0) { ++ isoc_warn("Ignoring NULL urb for epid:%d\n", epid); ++ continue; ++ } ++ if(!epid_out_traffic(epid)) { ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ if (urb_priv->urb_state == NOT_STARTED) { ++ /* If ASAP is not set and urb->start_frame is the current frame, ++ start the transfer. */ ++ if (!(urb->transfer_flags & URB_ISO_ASAP) && ++ (urb->start_frame == (*R_USB_FM_NUMBER & 0x7ff))) { ++ /* EP should not be enabled if we're waiting for start_frame */ ++ ASSERT((TxIsocEPList[epid].command & ++ IO_STATE(USB_EP_command, enable, yes)) == 0); ++ ++ isoc_warn("Enabling isoc IN EP descr for epid %d\n", epid); ++ TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ /* This urb is now active. */ ++ urb_priv->urb_state = STARTED; ++ continue; ++ } ++ } ++ } ++ } ++ ++ DBFEXIT; ++} ++ ++void crisv10_hcd_ctl_status_irq(struct crisv10_irq_reg *reg) ++{ ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(reg->hcd); ++ ++ DBFENTER; ++ ASSERT(crisv10_hcd); ++ ++ irq_dbg("ctr_status_irq, controller status: %s\n", ++ hcd_status_to_str(reg->r_usb_status)); ++ ++ /* FIXME: What should we do if we get ourun or perror? Dump the EP and SB ++ list for the corresponding epid? */ ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, ourun)) { ++ panic("USB controller got ourun."); ++ } ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, perror)) { ++ ++ /* Before, etrax_usb_do_intr_recover was called on this epid if it was ++ an interrupt pipe. I don't see how re-enabling all EP descriptors ++ will help if there was a programming error. */ ++ panic("USB controller got perror."); ++ } ++ ++ /* Keep track of USB Controller, if it's running or not */ ++ if(reg->r_usb_status & IO_STATE(R_USB_STATUS, running, yes)) { ++ crisv10_hcd->running = 1; ++ } else { ++ crisv10_hcd->running = 0; ++ } ++ ++ if (reg->r_usb_status & IO_MASK(R_USB_STATUS, device_mode)) { ++ /* We should never operate in device mode. */ ++ panic("USB controller in device mode."); ++ } ++ ++ /* Set the flag to avoid getting "Unlink after no-IRQ? Controller is probably ++ using the wrong IRQ" from hcd_unlink_urb() in drivers/usb/core/hcd.c */ ++ set_bit(HCD_FLAG_SAW_IRQ, ®->hcd->flags); ++ ++ DBFEXIT; ++} ++ ++ ++/******************************************************************/ ++/* Host Controller interface functions */ ++/******************************************************************/ ++ ++static inline void crisv10_ready_wait(void) { ++ volatile int timeout = 10000; ++ /* Check the busy bit of USB controller in Etrax */ ++ while((*R_USB_COMMAND & IO_MASK(R_USB_COMMAND, busy)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for USB controller to be idle\n"); ++ } ++} ++ ++/* reset host controller */ ++static int crisv10_hcd_reset(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "reset\n"); ++ ++ ++ /* Reset the USB interface. */ ++ /* ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, reset); ++ nop(); ++ */ ++ DBFEXIT; ++ return 0; ++} ++ ++/* start host controller */ ++static int crisv10_hcd_start(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "start\n"); ++ ++ crisv10_ready_wait(); ++ ++ /* Start processing of USB traffic. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ ++ nop(); ++ ++ hcd->state = HC_STATE_RUNNING; ++ ++ DBFEXIT; ++ return 0; ++} ++ ++/* stop host controller */ ++static void crisv10_hcd_stop(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ hcd_dbg(hcd, "stop\n"); ++ crisv10_hcd_reset(hcd); ++ DBFEXIT; ++} ++ ++/* return the current frame number */ ++static int crisv10_hcd_get_frame(struct usb_hcd *hcd) ++{ ++ DBFENTER; ++ DBFEXIT; ++ return (*R_USB_FM_NUMBER & 0x7ff); ++} ++ ++#ifdef CONFIG_USB_OTG ++ ++static int crisv10_hcd_start_port_reset(struct usb_hcd *hcd, unsigned port) ++{ ++ return 0; /* no-op for now */ ++} ++ ++#endif /* CONFIG_USB_OTG */ ++ ++ ++/******************************************************************/ ++/* Root Hub functions */ ++/******************************************************************/ ++ ++/* root hub status */ ++static const struct usb_hub_status rh_hub_status = ++ { ++ .wHubStatus = 0, ++ .wHubChange = 0, ++ }; ++ ++/* root hub descriptor */ ++static const u8 rh_hub_descr[] = ++ { ++ 0x09, /* bDescLength */ ++ 0x29, /* bDescriptorType */ ++ USB_ROOT_HUB_PORTS, /* bNbrPorts */ ++ 0x00, /* wHubCharacteristics */ ++ 0x00, ++ 0x01, /* bPwrOn2pwrGood */ ++ 0x00, /* bHubContrCurrent */ ++ 0x00, /* DeviceRemovable */ ++ 0xff /* PortPwrCtrlMask */ ++ }; ++ ++/* Actual holder of root hub status*/ ++struct crisv10_rh rh; ++ ++/* Initialize root hub data structures (called from dvdrv_hcd_probe()) */ ++int rh_init(void) { ++ int i; ++ /* Reset port status flags */ ++ for (i = 0; i < USB_ROOT_HUB_PORTS; i++) { ++ rh.wPortChange[i] = 0; ++ rh.wPortStatusPrev[i] = 0; ++ } ++ return 0; ++} ++ ++#define RH_FEAT_MASK ((1<<USB_PORT_FEAT_CONNECTION)|\ ++ (1<<USB_PORT_FEAT_ENABLE)|\ ++ (1<<USB_PORT_FEAT_SUSPEND)|\ ++ (1<<USB_PORT_FEAT_RESET)) ++ ++/* Handle port status change interrupt (called from bottom part interrupt) */ ++void rh_port_status_change(__u16 port_reg[]) { ++ int i; ++ __u16 wChange; ++ ++ for(i = 0; i < USB_ROOT_HUB_PORTS; i++) { ++ /* Xor out changes since last read, masked for important flags */ ++ wChange = (port_reg[i] & RH_FEAT_MASK) ^ rh.wPortStatusPrev[i]; ++ /* Or changes together with (if any) saved changes */ ++ rh.wPortChange[i] |= wChange; ++ /* Save new status */ ++ rh.wPortStatusPrev[i] = port_reg[i]; ++ ++ if(wChange) { ++ rh_dbg("Interrupt port_status change port%d: %s Current-status:%s\n", i+1, ++ port_status_to_str(wChange), ++ port_status_to_str(port_reg[i])); ++ } ++ } ++} ++ ++/* Construct port status change bitmap for the root hub */ ++static int rh_status_data_request(struct usb_hcd *hcd, char *buf) ++{ ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ unsigned int i; ++ ++ DBFENTER; ++ /* ++ * corresponds to hub status change EP (USB 2.0 spec section 11.13.4) ++ * return bitmap indicating ports with status change ++ */ ++ *buf = 0; ++ spin_lock(&crisv10_hcd->lock); ++ for (i = 1; i <= crisv10_hcd->num_ports; i++) { ++ if (rh.wPortChange[map_port(i)]) { ++ *buf |= (1 << i); ++ rh_dbg("rh_status_data_request, change on port %d: %s Current Status: %s\n", i, ++ port_status_to_str(rh.wPortChange[map_port(i)]), ++ port_status_to_str(rh.wPortStatusPrev[map_port(i)])); ++ } ++ } ++ spin_unlock(&crisv10_hcd->lock); ++ DBFEXIT; ++ return *buf == 0 ? 0 : 1; ++} ++ ++/* Handle a control request for the root hub (called from hcd_driver) */ ++static int rh_control_request(struct usb_hcd *hcd, ++ u16 typeReq, ++ u16 wValue, ++ u16 wIndex, ++ char *buf, ++ u16 wLength) { ++ ++ struct crisv10_hcd *crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ int retval = 0; ++ int len; ++ DBFENTER; ++ ++ switch (typeReq) { ++ case GetHubDescriptor: ++ rh_dbg("GetHubDescriptor\n"); ++ len = min_t(unsigned int, sizeof rh_hub_descr, wLength); ++ memcpy(buf, rh_hub_descr, len); ++ buf[2] = crisv10_hcd->num_ports; ++ break; ++ case GetHubStatus: ++ rh_dbg("GetHubStatus\n"); ++ len = min_t(unsigned int, sizeof rh_hub_status, wLength); ++ memcpy(buf, &rh_hub_status, len); ++ break; ++ case GetPortStatus: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ rh_dbg("GetportStatus, port:%d change:%s status:%s\n", wIndex, ++ port_status_to_str(rh.wPortChange[map_port(wIndex)]), ++ port_status_to_str(rh.wPortStatusPrev[map_port(wIndex)])); ++ *(u16 *) buf = cpu_to_le16(rh.wPortStatusPrev[map_port(wIndex)]); ++ *(u16 *) (buf + 2) = cpu_to_le16(rh.wPortChange[map_port(wIndex)]); ++ break; ++ case SetHubFeature: ++ rh_dbg("SetHubFeature\n"); ++ case ClearHubFeature: ++ rh_dbg("ClearHubFeature\n"); ++ switch (wValue) { ++ case C_HUB_OVER_CURRENT: ++ case C_HUB_LOCAL_POWER: ++ rh_warn("Not implemented hub request:%d \n", typeReq); ++ /* not implemented */ ++ break; ++ default: ++ goto error; ++ } ++ break; ++ case SetPortFeature: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ if(rh_set_port_feature(map_port(wIndex), wValue)) ++ goto error; ++ break; ++ case ClearPortFeature: ++ if (!wIndex || wIndex > crisv10_hcd->num_ports) ++ goto error; ++ if(rh_clear_port_feature(map_port(wIndex), wValue)) ++ goto error; ++ break; ++ default: ++ rh_warn("Unknown hub request: %d\n", typeReq); ++ error: ++ retval = -EPIPE; ++ } ++ DBFEXIT; ++ return retval; ++} ++ ++int rh_set_port_feature(__u8 bPort, __u16 wFeature) { ++ __u8 bUsbCommand = 0; ++ switch(wFeature) { ++ case USB_PORT_FEAT_RESET: ++ rh_dbg("SetPortFeature: reset\n"); ++ bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, reset); ++ goto set; ++ break; ++ case USB_PORT_FEAT_SUSPEND: ++ rh_dbg("SetPortFeature: suspend\n"); ++ bUsbCommand |= IO_STATE(R_USB_COMMAND, port_cmd, suspend); ++ goto set; ++ break; ++ case USB_PORT_FEAT_POWER: ++ rh_dbg("SetPortFeature: power\n"); ++ break; ++ case USB_PORT_FEAT_C_CONNECTION: ++ rh_dbg("SetPortFeature: c_connection\n"); ++ break; ++ case USB_PORT_FEAT_C_RESET: ++ rh_dbg("SetPortFeature: c_reset\n"); ++ break; ++ case USB_PORT_FEAT_C_OVER_CURRENT: ++ rh_dbg("SetPortFeature: c_over_current\n"); ++ break; ++ ++ set: ++ /* Select which port via the port_sel field */ ++ bUsbCommand |= IO_FIELD(R_USB_COMMAND, port_sel, bPort+1); ++ ++ /* Make sure the controller isn't busy. */ ++ crisv10_ready_wait(); ++ /* Send out the actual command to the USB controller */ ++ *R_USB_COMMAND = bUsbCommand; ++ ++ /* If port reset then also bring USB controller into running state */ ++ if(wFeature == USB_PORT_FEAT_RESET) { ++ /* Wait a while for controller to first become started after port reset */ ++ udelay(12000); /* 12ms blocking wait */ ++ ++ /* Make sure the controller isn't busy. */ ++ crisv10_ready_wait(); ++ ++ /* If all enabled ports were disabled the host controller goes down into ++ started mode, so we need to bring it back into the running state. ++ (This is safe even if it's already in the running state.) */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ } ++ ++ break; ++ default: ++ rh_dbg("SetPortFeature: unknown feature\n"); ++ return -1; ++ } ++ return 0; ++} ++ ++int rh_clear_port_feature(__u8 bPort, __u16 wFeature) { ++ switch(wFeature) { ++ case USB_PORT_FEAT_ENABLE: ++ rh_dbg("ClearPortFeature: enable\n"); ++ rh_disable_port(bPort); ++ break; ++ case USB_PORT_FEAT_SUSPEND: ++ rh_dbg("ClearPortFeature: suspend\n"); ++ break; ++ case USB_PORT_FEAT_POWER: ++ rh_dbg("ClearPortFeature: power\n"); ++ break; ++ ++ case USB_PORT_FEAT_C_ENABLE: ++ rh_dbg("ClearPortFeature: c_enable\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_SUSPEND: ++ rh_dbg("ClearPortFeature: c_suspend\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_CONNECTION: ++ rh_dbg("ClearPortFeature: c_connection\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_OVER_CURRENT: ++ rh_dbg("ClearPortFeature: c_over_current\n"); ++ goto clear; ++ case USB_PORT_FEAT_C_RESET: ++ rh_dbg("ClearPortFeature: c_reset\n"); ++ goto clear; ++ clear: ++ rh.wPortChange[bPort] &= ~(1 << (wFeature - 16)); ++ break; ++ default: ++ rh_dbg("ClearPortFeature: unknown feature\n"); ++ return -1; ++ } ++ return 0; ++} ++ ++ ++#ifdef CONFIG_PM ++/* Handle a suspend request for the root hub (called from hcd_driver) */ ++static int rh_suspend_request(struct usb_hcd *hcd) ++{ ++ return 0; /* no-op for now */ ++} ++ ++/* Handle a resume request for the root hub (called from hcd_driver) */ ++static int rh_resume_request(struct usb_hcd *hcd) ++{ ++ return 0; /* no-op for now */ ++} ++#endif /* CONFIG_PM */ ++ ++ ++ ++/* Wrapper function for workaround port disable registers in USB controller */ ++static void rh_disable_port(unsigned int port) { ++ volatile int timeout = 10000; ++ volatile char* usb_portx_disable; ++ switch(port) { ++ case 0: ++ usb_portx_disable = R_USB_PORT1_DISABLE; ++ break; ++ case 1: ++ usb_portx_disable = R_USB_PORT2_DISABLE; ++ break; ++ default: ++ /* Invalid port index */ ++ return; ++ } ++ /* Set disable flag in special register */ ++ *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, yes); ++ /* Wait until not enabled anymore */ ++ while((rh.wPortStatusPrev[port] & ++ IO_STATE(R_USB_RH_PORT_STATUS_1, enabled, yes)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for port %d to become disabled\n", port); ++ } ++ /* clear disable flag in special register */ ++ *usb_portx_disable = IO_STATE(R_USB_PORT1_DISABLE, disable, no); ++ rh_info("Physical port %d disabled\n", port+1); ++} ++ ++ ++/******************************************************************/ ++/* Transfer Controller (TC) functions */ ++/******************************************************************/ ++ ++/* FIXME: Should RX_BUF_SIZE be a config option, or maybe we should adjust it ++ dynamically? ++ To adjust it dynamically we would have to get an interrupt when we reach ++ the end of the rx descriptor list, or when we get close to the end, and ++ then allocate more descriptors. */ ++#define NBR_OF_RX_DESC 512 ++#define RX_DESC_BUF_SIZE 1024 ++#define RX_BUF_SIZE (NBR_OF_RX_DESC * RX_DESC_BUF_SIZE) ++ ++ ++/* Local variables for Transfer Controller */ ++/* --------------------------------------- */ ++ ++/* This is a circular (double-linked) list of the active urbs for each epid. ++ The head is never removed, and new urbs are linked onto the list as ++ urb_entry_t elements. Don't reference urb_list directly; use the wrapper ++ functions instead (which includes spin_locks) */ ++static struct list_head urb_list[NBR_OF_EPIDS]; ++ ++/* Read about the need and usage of this lock in submit_ctrl_urb. */ ++/* Lock for URB lists for each EPID */ ++static spinlock_t urb_list_lock; ++ ++/* Lock for EPID array register (R_USB_EPT_x) in Etrax */ ++static spinlock_t etrax_epid_lock; ++ ++/* Lock for dma8 sub0 handling */ ++static spinlock_t etrax_dma8_sub0_lock; ++ ++/* DMA IN cache bug. Align the DMA IN buffers to 32 bytes, i.e. a cache line. ++ Since RX_DESC_BUF_SIZE is 1024 is a multiple of 32, all rx buffers will be ++ cache aligned. */ ++static volatile unsigned char RxBuf[RX_BUF_SIZE] __attribute__ ((aligned (32))); ++static volatile struct USB_IN_Desc RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned (4))); ++ ++/* Pointers into RxDescList. */ ++static volatile struct USB_IN_Desc *myNextRxDesc; ++static volatile struct USB_IN_Desc *myLastRxDesc; ++ ++/* A zout transfer makes a memory access at the address of its buf pointer, ++ which means that setting this buf pointer to 0 will cause an access to the ++ flash. In addition to this, setting sw_len to 0 results in a 16/32 bytes ++ (depending on DMA burst size) transfer. ++ Instead, we set it to 1, and point it to this buffer. */ ++static int zout_buffer[4] __attribute__ ((aligned (4))); ++ ++/* Cache for allocating new EP and SB descriptors. */ ++static kmem_cache_t *usb_desc_cache; ++ ++/* Cache for the data allocated in the isoc descr top half. */ ++static kmem_cache_t *isoc_compl_cache; ++ ++/* Cache for the data allocated when delayed finishing of URBs */ ++static kmem_cache_t *later_data_cache; ++ ++ ++/* Counter to keep track of how many Isoc EP we have sat up. Used to enable ++ and disable iso_eof interrupt. We only need these interrupts when we have ++ Isoc data endpoints (consumes CPU cycles). ++ FIXME: This could be more fine granular, so this interrupt is only enabled ++ when we have a In Isoc URB not URB_ISO_ASAP flaged queued. */ ++static int isoc_epid_counter; ++ ++/* Protecting wrapper functions for R_USB_EPT_x */ ++/* -------------------------------------------- */ ++static inline void etrax_epid_set(__u8 index, __u32 data) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ *R_USB_EPT_DATA = data; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline void etrax_epid_clear_error(__u8 index) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ *R_USB_EPT_DATA &= ++ ~(IO_MASK(R_USB_EPT_DATA, error_count_in) | ++ IO_MASK(R_USB_EPT_DATA, error_count_out) | ++ IO_MASK(R_USB_EPT_DATA, error_code)); ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline void etrax_epid_set_toggle(__u8 index, __u8 dirout, ++ __u8 toggle) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ if(dirout) { ++ *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_out); ++ *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_out, toggle); ++ } else { ++ *R_USB_EPT_DATA &= ~IO_MASK(R_USB_EPT_DATA, t_in); ++ *R_USB_EPT_DATA |= IO_FIELD(R_USB_EPT_DATA, t_in, toggle); ++ } ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++} ++ ++static inline __u8 etrax_epid_get_toggle(__u8 index, __u8 dirout) { ++ unsigned long flags; ++ __u8 toggle; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ if (dirout) { ++ toggle = IO_EXTRACT(R_USB_EPT_DATA, t_out, *R_USB_EPT_DATA); ++ } else { ++ toggle = IO_EXTRACT(R_USB_EPT_DATA, t_in, *R_USB_EPT_DATA); ++ } ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ return toggle; ++} ++ ++ ++static inline __u32 etrax_epid_get(__u8 index) { ++ unsigned long flags; ++ __u32 data; ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, index); ++ nop(); ++ data = *R_USB_EPT_DATA; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ return data; ++} ++ ++ ++ ++ ++/* Main functions for Transfer Controller */ ++/* -------------------------------------- */ ++ ++/* Init structs, memories and lists used by Transfer Controller */ ++int tc_init(struct usb_hcd *hcd) { ++ int i; ++ /* Clear software state info for all epids */ ++ memset(epid_state, 0, sizeof(struct etrax_epid) * NBR_OF_EPIDS); ++ ++ /* Set Invalid and Dummy as being in use and disabled */ ++ epid_state[INVALID_EPID].inuse = 1; ++ epid_state[DUMMY_EPID].inuse = 1; ++ epid_state[INVALID_EPID].disabled = 1; ++ epid_state[DUMMY_EPID].disabled = 1; ++ ++ /* Clear counter for how many Isoc epids we have sat up */ ++ isoc_epid_counter = 0; ++ ++ /* Initialize the urb list by initiating a head for each list. ++ Also reset list hodling active URB for each epid */ ++ for (i = 0; i < NBR_OF_EPIDS; i++) { ++ INIT_LIST_HEAD(&urb_list[i]); ++ activeUrbList[i] = NULL; ++ } ++ ++ /* Init lock for URB lists */ ++ spin_lock_init(&urb_list_lock); ++ /* Init lock for Etrax R_USB_EPT register */ ++ spin_lock_init(&etrax_epid_lock); ++ /* Init lock for Etrax dma8 sub0 handling */ ++ spin_lock_init(&etrax_dma8_sub0_lock); ++ ++ /* We use kmem_cache_* to make sure that all DMA desc. are dword aligned */ ++ ++ /* Note that we specify sizeof(struct USB_EP_Desc) as the size, but also ++ allocate SB descriptors from this cache. This is ok since ++ sizeof(struct USB_EP_Desc) == sizeof(struct USB_SB_Desc). */ ++ usb_desc_cache = kmem_cache_create("usb_desc_cache", ++ sizeof(struct USB_EP_Desc), 0, ++ SLAB_HWCACHE_ALIGN, 0, 0); ++ if(usb_desc_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ /* Create slab cache for speedy allocation of memory for isoc bottom-half ++ interrupt handling */ ++ isoc_compl_cache = ++ kmem_cache_create("isoc_compl_cache", ++ sizeof(struct crisv10_isoc_complete_data), ++ 0, SLAB_HWCACHE_ALIGN, 0, 0); ++ if(isoc_compl_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ /* Create slab cache for speedy allocation of memory for later URB finish ++ struct */ ++ later_data_cache = ++ kmem_cache_create("later_data_cache", ++ sizeof(struct urb_later_data), ++ 0, SLAB_HWCACHE_ALIGN, 0, 0); ++ if(later_data_cache == NULL) { ++ return -ENOMEM; ++ } ++ ++ ++ /* Initiate the bulk start timer. */ ++ init_timer(&bulk_start_timer); ++ bulk_start_timer.expires = jiffies + BULK_START_TIMER_INTERVAL; ++ bulk_start_timer.function = tc_bulk_start_timer_func; ++ add_timer(&bulk_start_timer); ++ ++ ++ /* Initiate the bulk eot timer. */ ++ init_timer(&bulk_eot_timer); ++ bulk_eot_timer.expires = jiffies + BULK_EOT_TIMER_INTERVAL; ++ bulk_eot_timer.function = tc_bulk_eot_timer_func; ++ bulk_eot_timer.data = (unsigned long)hcd; ++ add_timer(&bulk_eot_timer); ++ ++ return 0; ++} ++ ++/* Uninitialize all resources used by Transfer Controller */ ++void tc_destroy(void) { ++ ++ /* Destroy all slab cache */ ++ kmem_cache_destroy(usb_desc_cache); ++ kmem_cache_destroy(isoc_compl_cache); ++ kmem_cache_destroy(later_data_cache); ++ ++ /* Remove timers */ ++ del_timer(&bulk_start_timer); ++ del_timer(&bulk_eot_timer); ++} ++ ++static void restart_dma8_sub0(void) { ++ unsigned long flags; ++ spin_lock_irqsave(&etrax_dma8_sub0_lock, flags); ++ /* Verify that the dma is not running */ ++ if ((*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd)) == 0) { ++ struct USB_EP_Desc *ep = (struct USB_EP_Desc *)phys_to_virt(*R_DMA_CH8_SUB0_EP); ++ while (DUMMY_EPID == IO_EXTRACT(USB_EP_command, epid, ep->command)) { ++ ep = (struct USB_EP_Desc *)phys_to_virt(ep->next); ++ } ++ /* Advance the DMA to the next EP descriptor that is not a DUMMY_EPID. ++ * ep->next is already a physical address; no need for a virt_to_phys. */ ++ *R_DMA_CH8_SUB0_EP = ep->next; ++ /* Restart the DMA */ ++ *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); ++ } ++ spin_unlock_irqrestore(&etrax_dma8_sub0_lock, flags); ++} ++ ++/* queue an URB with the transfer controller (called from hcd_driver) */ ++static int tc_urb_enqueue(struct usb_hcd *hcd, ++ struct usb_host_endpoint *ep, ++ struct urb *urb, ++ gfp_t mem_flags) { ++ int epid; ++ int retval; ++ int bustime = 0; ++ int maxpacket; ++ unsigned long flags; ++ struct crisv10_urb_priv *urb_priv; ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ DBFENTER; ++ ++ if(!(crisv10_hcd->running)) { ++ /* The USB Controller is not running, probably because no device is ++ attached. No idea to enqueue URBs then */ ++ tc_warn("Rejected enqueueing of URB:0x%x because no dev attached\n", ++ (unsigned int)urb); ++ return -ENOENT; ++ } ++ ++ maxpacket = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); ++ /* Special case check for In Isoc transfers. Specification states that each ++ In Isoc transfer consists of one packet and therefore it should fit into ++ the transfer-buffer of an URB. ++ We do the check here to be sure (an invalid scenario can be produced with ++ parameters to the usbtest suite) */ ++ if(usb_pipeisoc(urb->pipe) && usb_pipein(urb->pipe) && ++ (urb->transfer_buffer_length < maxpacket)) { ++ tc_err("Submit In Isoc URB with buffer length:%d to pipe with maxpacketlen: %d\n", urb->transfer_buffer_length, maxpacket); ++ return -EMSGSIZE; ++ } ++ ++ /* Check if there is enough bandwidth for periodic transfer */ ++ if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) { ++ /* only check (and later claim) if not already claimed */ ++ if (urb->bandwidth == 0) { ++ bustime = usb_check_bandwidth(urb->dev, urb); ++ if (bustime < 0) { ++ tc_err("Not enough periodic bandwidth\n"); ++ return -ENOSPC; ++ } ++ } ++ } ++ ++ /* Check if there is a epid for URBs destination, if not this function ++ set up one. */ ++ epid = tc_setup_epid(ep, urb, mem_flags); ++ if (epid < 0) { ++ tc_err("Failed setup epid:%d for URB:0x%x\n", epid, (unsigned int)urb); ++ DBFEXIT; ++ return -ENOMEM; ++ } ++ ++ if(urb == activeUrbList[epid]) { ++ tc_err("Resubmition of allready active URB:0x%x\n", (unsigned int)urb); ++ return -ENXIO; ++ } ++ ++ if(urb_list_entry(urb, epid)) { ++ tc_err("Resubmition of allready queued URB:0x%x\n", (unsigned int)urb); ++ return -ENXIO; ++ } ++ ++ /* If we actively have flaged endpoint as disabled then refuse submition */ ++ if(epid_state[epid].disabled) { ++ return -ENOENT; ++ } ++ ++ /* Allocate and init HC-private data for URB */ ++ if(urb_priv_create(hcd, urb, epid, mem_flags) != 0) { ++ DBFEXIT; ++ return -ENOMEM; ++ } ++ urb_priv = urb->hcpriv; ++ ++ tc_dbg("Enqueue URB:0x%x[%d] epid:%d (%s) bufflen:%d\n", ++ (unsigned int)urb, urb_priv->urb_num, epid, ++ pipe_to_str(urb->pipe), urb->transfer_buffer_length); ++ ++ /* Create and link SBs required for this URB */ ++ retval = create_sb_for_urb(urb, mem_flags); ++ if(retval != 0) { ++ tc_err("Failed to create SBs for URB:0x%x[%d]\n", (unsigned int)urb, ++ urb_priv->urb_num); ++ urb_priv_free(hcd, urb); ++ DBFEXIT; ++ return retval; ++ } ++ ++ /* Init intr EP pool if this URB is a INTR transfer. This pool is later ++ used when inserting EPs in the TxIntrEPList. We do the alloc here ++ so we can't run out of memory later */ ++ if(usb_pipeint(urb->pipe)) { ++ retval = init_intr_urb(urb, mem_flags); ++ if(retval != 0) { ++ tc_warn("Failed to init Intr URB\n"); ++ urb_priv_free(hcd, urb); ++ DBFEXIT; ++ return retval; ++ } ++ } ++ ++ /* Disable other access when inserting USB */ ++ local_irq_save(flags); ++ ++ /* Claim bandwidth, if needed */ ++ if(bustime) { ++ usb_claim_bandwidth(urb->dev, urb, bustime, 0); ++ } ++ ++ /* Add URB to EP queue */ ++ urb_list_add(urb, epid, mem_flags); ++ ++ if(usb_pipeisoc(urb->pipe)) { ++ /* Special processing of Isoc URBs. */ ++ tc_dma_process_isoc_urb(urb); ++ } else { ++ /* Process EP queue for rest of the URB types (Bulk, Ctrl, Intr) */ ++ tc_dma_process_queue(epid); ++ } ++ ++ local_irq_restore(flags); ++ ++ DBFEXIT; ++ return 0; ++} ++ ++/* remove an URB from the transfer controller queues (called from hcd_driver)*/ ++static int tc_urb_dequeue(struct usb_hcd *hcd, struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv; ++ unsigned long flags; ++ int epid; ++ ++ DBFENTER; ++ /* Disable interrupts here since a descriptor interrupt for the isoc epid ++ will modify the sb list. This could possibly be done more granular, but ++ urb_dequeue should not be used frequently anyway. ++ */ ++ local_irq_save(flags); ++ ++ urb_priv = urb->hcpriv; ++ ++ if (!urb_priv) { ++ /* This happens if a device driver calls unlink on an urb that ++ was never submitted (lazy driver) or if the urb was completed ++ while dequeue was being called. */ ++ tc_warn("Dequeing of not enqueued URB:0x%x\n", (unsigned int)urb); ++ local_irq_restore(flags); ++ return 0; ++ } ++ epid = urb_priv->epid; ++ ++ tc_warn("Dequeing %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ /* For Bulk, Ctrl and Intr are only one URB active at a time. So any URB ++ that isn't active can be dequeued by just removing it from the queue */ ++ if(usb_pipebulk(urb->pipe) || usb_pipecontrol(urb->pipe) || ++ usb_pipeint(urb->pipe)) { ++ ++ /* Check if URB haven't gone further than the queue */ ++ if(urb != activeUrbList[epid]) { ++ ASSERT(urb_priv->later_data == NULL); ++ tc_warn("Dequeing URB:0x%x[%d] (%s %s epid:%d) from queue" ++ " (not active)\n", (unsigned int)urb, urb_priv->urb_num, ++ str_dir(urb->pipe), str_type(urb->pipe), epid); ++ ++ /* Finish the URB with error status from USB core */ ++ tc_finish_urb(hcd, urb, urb->status); ++ local_irq_restore(flags); ++ return 0; ++ } ++ } ++ ++ /* Set URB status to Unlink for handling when interrupt comes. */ ++ urb_priv->urb_state = UNLINK; ++ ++ /* Differentiate dequeing of Bulk and Ctrl from Isoc and Intr */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Check if EP still is enabled */ ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ /* Kicking dummy list out of the party. */ ++ TxBulkEPList[epid].next = virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); ++ break; ++ case PIPE_CONTROL: ++ /* Check if EP still is enabled */ ++ if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ break; ++ case PIPE_ISOCHRONOUS: ++ /* Disabling, busy-wait and unlinking of Isoc SBs will be done in ++ finish_isoc_urb(). Because there might the case when URB is dequeued ++ but there are other valid URBs waiting */ ++ ++ /* Check if In Isoc EP still is enabled */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ break; ++ case PIPE_INTERRUPT: ++ /* Special care is taken for interrupt URBs. EPs are unlinked in ++ tc_finish_urb */ ++ break; ++ default: ++ break; ++ } ++ ++ /* Asynchronous unlink, finish the URB later from scheduled or other ++ event (data finished, error) */ ++ tc_finish_urb_later(hcd, urb, urb->status); ++ ++ local_irq_restore(flags); ++ DBFEXIT; ++ return 0; ++} ++ ++ ++static void tc_sync_finish_epid(struct usb_hcd *hcd, int epid) { ++ volatile int timeout = 10000; ++ struct urb* urb; ++ struct crisv10_urb_priv* urb_priv; ++ unsigned long flags; ++ ++ volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */ ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ ++ int type = epid_state[epid].type; ++ ++ /* Setting this flag will cause enqueue() to return -ENOENT for new ++ submitions on this endpoint and finish_urb() wont process queue further */ ++ epid_state[epid].disabled = 1; ++ ++ switch(type) { ++ case PIPE_BULK: ++ /* Check if EP still is enabled */ ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxBulkEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ tc_warn("sync_finish: Disabling EP for epid:%d\n", epid); ++ ++ /* Do busy-wait until DMA not using this EP descriptor anymore */ ++ while((*R_DMA_CH8_SUB0_EP == ++ virt_to_phys(&TxBulkEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Bulk to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ ++ case PIPE_CONTROL: ++ /* Check if EP still is enabled */ ++ if (TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ /* The EP was enabled, disable it. */ ++ TxCtrlEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ tc_warn("sync_finish: Disabling EP for epid:%d\n", epid); ++ ++ /* Do busy-wait until DMA not using this EP descriptor anymore */ ++ while((*R_DMA_CH8_SUB1_EP == ++ virt_to_phys(&TxCtrlEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Ctrl to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ ++ case PIPE_INTERRUPT: ++ local_irq_save(flags); ++ /* Disable all Intr EPs belonging to epid */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* Disable EP */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ local_irq_restore(flags); ++ break; ++ ++ case PIPE_ISOCHRONOUS: ++ /* Check if EP still is enabled */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ tc_warn("sync_finish: Disabling Isoc EP for epid:%d\n", epid); ++ /* The EP was enabled, disable it. */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ ++ while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Isoc to leave EP for" ++ " epid:%d\n", epid); ++ } ++ } ++ break; ++ } ++ ++ local_irq_save(flags); ++ ++ /* Finish if there is active URB for this endpoint */ ++ if(activeUrbList[epid] != NULL) { ++ urb = activeUrbList[epid]; ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv); ++ tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ tc_finish_urb(hcd, activeUrbList[epid], -ENOENT); ++ ASSERT(activeUrbList[epid] == NULL); ++ } ++ ++ /* Finish any queued URBs for this endpoint. There won't be any resubmitions ++ because epid_disabled causes enqueue() to fail for this endpoint */ ++ while((urb = urb_list_first(epid)) != NULL) { ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ tc_warn("Sync finish %s URB:0x%x[%d] (%s %s epid:%d) status:%d %s\n", ++ (urb == activeUrbList[epid]) ? "active" : "queued", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), epid, urb->status, ++ (urb_priv->later_data) ? "later-sched" : ""); ++ ++ tc_finish_urb(hcd, urb, -ENOENT); ++ } ++ epid_state[epid].disabled = 0; ++ local_irq_restore(flags); ++} ++ ++/* free resources associated with an endpoint (called from hcd_driver) */ ++static void tc_endpoint_disable(struct usb_hcd *hcd, ++ struct usb_host_endpoint *ep) { ++ DBFENTER; ++ /* Only free epid if it has been allocated. We get two endpoint_disable ++ requests for ctrl endpoints so ignore the second one */ ++ if(ep->hcpriv != NULL) { ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ int epid = ep_priv->epid; ++ tc_warn("endpoint_disable ep:0x%x ep-priv:0x%x (%s) (epid:%d freed)\n", ++ (unsigned int)ep, (unsigned int)ep->hcpriv, ++ endpoint_to_str(&(ep->desc)), epid); ++ ++ tc_sync_finish_epid(hcd, epid); ++ ++ ASSERT(activeUrbList[epid] == NULL); ++ ASSERT(list_empty(&urb_list[epid])); ++ ++ tc_free_epid(ep); ++ } else { ++ tc_dbg("endpoint_disable ep:0x%x ep-priv:0x%x (%s)\n", (unsigned int)ep, ++ (unsigned int)ep->hcpriv, endpoint_to_str(&(ep->desc))); ++ } ++ DBFEXIT; ++} ++ ++static void tc_finish_urb_later_proc(void *data) { ++ unsigned long flags; ++ struct urb_later_data* uld = (struct urb_later_data*)data; ++ local_irq_save(flags); ++ if(uld->urb == NULL) { ++ late_dbg("Later finish of URB = NULL (allready finished)\n"); ++ } else { ++ struct crisv10_urb_priv* urb_priv = uld->urb->hcpriv; ++ ASSERT(urb_priv); ++ if(urb_priv->urb_num == uld->urb_num) { ++ late_dbg("Later finish of URB:0x%x[%d]\n", (unsigned int)(uld->urb), ++ urb_priv->urb_num); ++ if(uld->status != uld->urb->status) { ++ errno_dbg("Later-finish URB with status:%d, later-status:%d\n", ++ uld->urb->status, uld->status); ++ } ++ if(uld != urb_priv->later_data) { ++ panic("Scheduled uld not same as URBs uld\n"); ++ } ++ tc_finish_urb(uld->hcd, uld->urb, uld->status); ++ } else { ++ late_warn("Ignoring later finish of URB:0x%x[%d]" ++ ", urb_num doesn't match current URB:0x%x[%d]", ++ (unsigned int)(uld->urb), uld->urb_num, ++ (unsigned int)(uld->urb), urb_priv->urb_num); ++ } ++ } ++ local_irq_restore(flags); ++ kmem_cache_free(later_data_cache, uld); ++} ++ ++static void tc_finish_urb_later(struct usb_hcd *hcd, struct urb *urb, ++ int status) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ struct urb_later_data* uld; ++ ++ ASSERT(urb_priv); ++ ++ if(urb_priv->later_data != NULL) { ++ /* Later-finish allready scheduled for this URB, just update status to ++ return when finishing later */ ++ errno_dbg("Later-finish schedule change URB status:%d with new" ++ " status:%d\n", urb_priv->later_data->status, status); ++ ++ urb_priv->later_data->status = status; ++ return; ++ } ++ ++ uld = kmem_cache_alloc(later_data_cache, SLAB_ATOMIC); ++ ASSERT(uld); ++ ++ uld->hcd = hcd; ++ uld->urb = urb; ++ uld->urb_num = urb_priv->urb_num; ++ uld->status = status; ++ ++ INIT_WORK(&uld->ws, tc_finish_urb_later_proc, uld); ++ urb_priv->later_data = uld; ++ ++ /* Schedule the finishing of the URB to happen later */ ++ schedule_delayed_work(&uld->ws, LATER_TIMER_DELAY); ++} ++ ++static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb, ++ int status); ++ ++static void tc_finish_urb(struct usb_hcd *hcd, struct urb *urb, int status) { ++ struct crisv10_hcd* crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid; ++ char toggle; ++ int urb_num; ++ ++ DBFENTER; ++ ASSERT(urb_priv != NULL); ++ epid = urb_priv->epid; ++ urb_num = urb_priv->urb_num; ++ ++ if(urb != activeUrbList[epid]) { ++ if(urb_list_entry(urb, epid)) { ++ /* Remove this URB from the list. Only happens when URB are finished ++ before having been processed (dequeing) */ ++ urb_list_del(urb, epid); ++ } else { ++ tc_warn("Finishing of URB:0x%x[%d] neither active or in queue for" ++ " epid:%d\n", (unsigned int)urb, urb_num, epid); ++ } ++ } ++ ++ /* Cancel any pending later-finish of this URB */ ++ if(urb_priv->later_data) { ++ urb_priv->later_data->urb = NULL; ++ } ++ ++ /* For an IN pipe, we always set the actual length, regardless of whether ++ there was an error or not (which means the device driver can use the data ++ if it wants to). */ ++ if(usb_pipein(urb->pipe)) { ++ urb->actual_length = urb_priv->rx_offset; ++ } else { ++ /* Set actual_length for OUT urbs also; the USB mass storage driver seems ++ to want that. */ ++ if (status == 0 && urb->status == -EINPROGRESS) { ++ urb->actual_length = urb->transfer_buffer_length; ++ } else { ++ /* We wouldn't know of any partial writes if there was an error. */ ++ urb->actual_length = 0; ++ } ++ } ++ ++ ++ /* URB status mangling */ ++ if(urb->status == -EINPROGRESS) { ++ /* The USB core hasn't changed the status, let's set our finish status */ ++ urb->status = status; ++ ++ if ((status == 0) && (urb->transfer_flags & URB_SHORT_NOT_OK) && ++ usb_pipein(urb->pipe) && ++ (urb->actual_length != urb->transfer_buffer_length)) { ++ /* URB_SHORT_NOT_OK means that short reads (shorter than the endpoint's ++ max length) is to be treated as an error. */ ++ errno_dbg("Finishing URB:0x%x[%d] with SHORT_NOT_OK flag and short" ++ " data:%d\n", (unsigned int)urb, urb_num, ++ urb->actual_length); ++ urb->status = -EREMOTEIO; ++ } ++ ++ if(urb_priv->urb_state == UNLINK) { ++ /* URB has been requested to be unlinked asynchronously */ ++ urb->status = -ECONNRESET; ++ errno_dbg("Fixing unlink status of URB:0x%x[%d] to:%d\n", ++ (unsigned int)urb, urb_num, urb->status); ++ } ++ } else { ++ /* The USB Core wants to signal some error via the URB, pass it through */ ++ } ++ ++ /* use completely different finish function for Isoc URBs */ ++ if(usb_pipeisoc(urb->pipe)) { ++ tc_finish_isoc_urb(hcd, urb, status); ++ return; ++ } ++ ++ /* Do special unlinking of EPs for Intr traffic */ ++ if(usb_pipeint(urb->pipe)) { ++ tc_dma_unlink_intr_urb(urb); ++ } ++ ++ /* Release allocated bandwidth for periodic transfers */ ++ if(usb_pipeint(urb->pipe) || usb_pipeisoc(urb->pipe)) ++ usb_release_bandwidth(urb->dev, urb, 0); ++ ++ /* This URB is active on EP */ ++ if(urb == activeUrbList[epid]) { ++ /* We need to fiddle with the toggle bits because the hardware doesn't do ++ it for us. */ ++ toggle = etrax_epid_get_toggle(epid, usb_pipeout(urb->pipe)); ++ usb_settoggle(urb->dev, usb_pipeendpoint(urb->pipe), ++ usb_pipeout(urb->pipe), toggle); ++ ++ /* Checks for Ctrl and Bulk EPs */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Check so Bulk EP realy is disabled before finishing active URB */ ++ ASSERT((TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) == ++ IO_STATE(USB_EP_command, enable, no)); ++ /* Disable sub-pointer for EP to avoid next tx_interrupt() to ++ process Bulk EP. */ ++ TxBulkEPList[epid].sub = 0; ++ /* No need to wait for the DMA before changing the next pointer. ++ The modulo NBR_OF_EPIDS isn't actually necessary, since we will never use ++ the last one (INVALID_EPID) for actual traffic. */ ++ TxBulkEPList[epid].next = ++ virt_to_phys(&TxBulkEPList[(epid + 1) % NBR_OF_EPIDS]); ++ break; ++ case PIPE_CONTROL: ++ /* Check so Ctrl EP realy is disabled before finishing active URB */ ++ ASSERT((TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) == ++ IO_STATE(USB_EP_command, enable, no)); ++ /* Disable sub-pointer for EP to avoid next tx_interrupt() to ++ process Ctrl EP. */ ++ TxCtrlEPList[epid].sub = 0; ++ break; ++ } ++ } ++ ++ /* Free HC-private URB data*/ ++ urb_priv_free(hcd, urb); ++ ++ if(urb->status) { ++ errno_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n", ++ (unsigned int)urb, urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb->actual_length, urb->status); ++ } else { ++ tc_dbg("finish_urb (URB:0x%x[%d] %s %s) (data:%d) status:%d\n", ++ (unsigned int)urb, urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb->actual_length, urb->status); ++ } ++ ++ /* If we just finished an active URB, clear active pointer. */ ++ if (urb == activeUrbList[epid]) { ++ /* Make URB not active on EP anymore */ ++ activeUrbList[epid] = NULL; ++ ++ if(urb->status == 0) { ++ /* URB finished sucessfully, process queue to see if there are any more ++ URBs waiting before we call completion function.*/ ++ if(crisv10_hcd->running) { ++ /* Only process queue if USB controller is running */ ++ tc_dma_process_queue(epid); ++ } else { ++ tc_warn("No processing of queue for epid:%d, USB Controller not" ++ " running\n", epid); ++ } ++ } ++ } ++ ++ /* Hand the URB from HCD to its USB device driver, using its completion ++ functions */ ++ usb_hcd_giveback_urb (hcd, urb); ++ ++ /* Check the queue once more if the URB returned with error, because we ++ didn't do it before the completion function because the specification ++ states that the queue should not restart until all it's unlinked ++ URBs have been fully retired, with the completion functions run */ ++ if(crisv10_hcd->running) { ++ /* Only process queue if USB controller is running */ ++ tc_dma_process_queue(epid); ++ } else { ++ tc_warn("No processing of queue for epid:%d, USB Controller not running\n", ++ epid); ++ } ++ ++ DBFEXIT; ++} ++ ++static void tc_finish_isoc_urb(struct usb_hcd *hcd, struct urb *urb, ++ int status) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid, i; ++ volatile int timeout = 10000; ++ ++ ASSERT(urb_priv); ++ epid = urb_priv->epid; ++ ++ ASSERT(usb_pipeisoc(urb->pipe)); ++ ++ /* Set that all isoc packets have status and length set before ++ completing the urb. */ ++ for (i = urb_priv->isoc_packet_counter; i < urb->number_of_packets; i++){ ++ urb->iso_frame_desc[i].actual_length = 0; ++ urb->iso_frame_desc[i].status = -EPROTO; ++ } ++ ++ /* Check if the URB is currently active (done or error) */ ++ if(urb == activeUrbList[epid]) { ++ /* Check if there are another In Isoc URB queued for this epid */ ++ if (!list_empty(&urb_list[epid])&& !epid_state[epid].disabled) { ++ /* Move it from queue to active and mark it started so Isoc transfers ++ won't be interrupted. ++ All Isoc URBs data transfers are already added to DMA lists so we ++ don't have to insert anything in DMA lists here. */ ++ activeUrbList[epid] = urb_list_first(epid); ++ ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_state = ++ STARTED; ++ urb_list_del(activeUrbList[epid], epid); ++ ++ if(urb->status) { ++ errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)" ++ " status:%d, new waiting URB:0x%x[%d]\n", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb_priv->isoc_packet_counter, ++ urb->number_of_packets, urb->status, ++ (unsigned int)activeUrbList[epid], ++ ((struct crisv10_urb_priv *)(activeUrbList[epid]->hcpriv))->urb_num); ++ } ++ ++ } else { /* No other URB queued for this epid */ ++ if(urb->status) { ++ errno_dbg("finish_isoc_urb (URB:0x%x[%d] %s %s) (%d of %d packets)" ++ " status:%d, no new URB waiting\n", ++ (unsigned int)urb, urb_priv->urb_num, str_dir(urb->pipe), ++ str_type(urb->pipe), urb_priv->isoc_packet_counter, ++ urb->number_of_packets, urb->status); ++ } ++ ++ /* Check if EP is still enabled, then shut it down. */ ++ if (TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ isoc_dbg("Isoc EP enabled for epid:%d, disabling it\n", epid); ++ ++ /* Should only occur for In Isoc EPs where SB isn't consumed. */ ++ ASSERT(usb_pipein(urb->pipe)); ++ ++ /* Disable it and wait for it to stop */ ++ TxIsocEPList[epid].command &= ~IO_MASK(USB_EP_command, enable); ++ ++ /* Ah, the luxury of busy-wait. */ ++ while((*R_DMA_CH8_SUB3_EP == virt_to_phys(&TxIsocEPList[epid])) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Isoc to leave EP for epid:%d\n", epid); ++ } ++ } ++ ++ /* Unlink SB to say that epid is finished. */ ++ TxIsocEPList[epid].sub = 0; ++ TxIsocEPList[epid].hw_len = 0; ++ ++ /* No URB active for EP anymore */ ++ activeUrbList[epid] = NULL; ++ } ++ } else { /* Finishing of not active URB (queued up with SBs thought) */ ++ isoc_warn("finish_isoc_urb (URB:0x%x %s) (%d of %d packets) status:%d," ++ " SB queued but not active\n", ++ (unsigned int)urb, str_dir(urb->pipe), ++ urb_priv->isoc_packet_counter, urb->number_of_packets, ++ urb->status); ++ if(usb_pipeout(urb->pipe)) { ++ /* Finishing of not yet active Out Isoc URB needs unlinking of SBs. */ ++ struct USB_SB_Desc *iter_sb, *prev_sb, *next_sb; ++ ++ iter_sb = TxIsocEPList[epid].sub ? ++ phys_to_virt(TxIsocEPList[epid].sub) : 0; ++ prev_sb = 0; ++ ++ /* SB that is linked before this URBs first SB */ ++ while (iter_sb && (iter_sb != urb_priv->first_sb)) { ++ prev_sb = iter_sb; ++ iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } ++ ++ if (iter_sb == 0) { ++ /* Unlink of the URB currently being transmitted. */ ++ prev_sb = 0; ++ iter_sb = TxIsocEPList[epid].sub ? phys_to_virt(TxIsocEPList[epid].sub) : 0; ++ } ++ ++ while (iter_sb && (iter_sb != urb_priv->last_sb)) { ++ iter_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } ++ ++ if (iter_sb) { ++ next_sb = iter_sb->next ? phys_to_virt(iter_sb->next) : 0; ++ } else { ++ /* This should only happen if the DMA has completed ++ processing the SB list for this EP while interrupts ++ are disabled. */ ++ isoc_dbg("Isoc urb not found, already sent?\n"); ++ next_sb = 0; ++ } ++ if (prev_sb) { ++ prev_sb->next = next_sb ? virt_to_phys(next_sb) : 0; ++ } else { ++ TxIsocEPList[epid].sub = next_sb ? virt_to_phys(next_sb) : 0; ++ } ++ } ++ } ++ ++ /* Free HC-private URB data*/ ++ urb_priv_free(hcd, urb); ++ ++ usb_release_bandwidth(urb->dev, urb, 0); ++ ++ /* Hand the URB from HCD to its USB device driver, using its completion ++ functions */ ++ usb_hcd_giveback_urb (hcd, urb); ++} ++ ++static __u32 urb_num = 0; ++ ++/* allocate and initialize URB private data */ ++static int urb_priv_create(struct usb_hcd *hcd, struct urb *urb, int epid, ++ int mem_flags) { ++ struct crisv10_urb_priv *urb_priv; ++ ++ urb_priv = kmalloc(sizeof *urb_priv, mem_flags); ++ if (!urb_priv) ++ return -ENOMEM; ++ memset(urb_priv, 0, sizeof *urb_priv); ++ ++ urb_priv->epid = epid; ++ urb_priv->urb_state = NOT_STARTED; ++ ++ urb->hcpriv = urb_priv; ++ /* Assign URB a sequence number, and increment counter */ ++ urb_priv->urb_num = urb_num; ++ urb_num++; ++ return 0; ++} ++ ++/* free URB private data */ ++static void urb_priv_free(struct usb_hcd *hcd, struct urb *urb) { ++ int i; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ ASSERT(urb_priv != 0); ++ ++ /* Check it has any SBs linked that needs to be freed*/ ++ if(urb_priv->first_sb != NULL) { ++ struct USB_SB_Desc *next_sb, *first_sb, *last_sb; ++ int i = 0; ++ first_sb = urb_priv->first_sb; ++ last_sb = urb_priv->last_sb; ++ ASSERT(last_sb); ++ while(first_sb != last_sb) { ++ next_sb = (struct USB_SB_Desc *)phys_to_virt(first_sb->next); ++ kmem_cache_free(usb_desc_cache, first_sb); ++ first_sb = next_sb; ++ i++; ++ } ++ kmem_cache_free(usb_desc_cache, last_sb); ++ i++; ++ } ++ ++ /* Check if it has any EPs in its Intr pool that also needs to be freed */ ++ if(urb_priv->intr_ep_pool_length > 0) { ++ for(i = 0; i < urb_priv->intr_ep_pool_length; i++) { ++ kfree(urb_priv->intr_ep_pool[i]); ++ } ++ /* ++ tc_dbg("Freed %d EPs from URB:0x%x EP pool\n", ++ urb_priv->intr_ep_pool_length, (unsigned int)urb); ++ */ ++ } ++ ++ kfree(urb_priv); ++ urb->hcpriv = NULL; ++} ++ ++static int ep_priv_create(struct usb_host_endpoint *ep, int mem_flags) { ++ struct crisv10_ep_priv *ep_priv; ++ ++ ep_priv = kmalloc(sizeof *ep_priv, mem_flags); ++ if (!ep_priv) ++ return -ENOMEM; ++ memset(ep_priv, 0, sizeof *ep_priv); ++ ++ ep->hcpriv = ep_priv; ++ return 0; ++} ++ ++static void ep_priv_free(struct usb_host_endpoint *ep) { ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ ASSERT(ep_priv); ++ kfree(ep_priv); ++ ep->hcpriv = NULL; ++} ++ ++/* EPID handling functions, managing EP-list in Etrax through wrappers */ ++/* ------------------------------------------------------------------- */ ++ ++/* Sets up a new EPID for an endpoint or returns existing if found */ ++static int tc_setup_epid(struct usb_host_endpoint *ep, struct urb *urb, ++ int mem_flags) { ++ int epid; ++ char devnum, endpoint, out_traffic, slow; ++ int maxlen; ++ __u32 epid_data; ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ ++ DBFENTER; ++ ++ /* Check if a valid epid already is setup for this endpoint */ ++ if(ep_priv != NULL) { ++ return ep_priv->epid; ++ } ++ ++ /* We must find and initiate a new epid for this urb. */ ++ epid = tc_allocate_epid(); ++ ++ if (epid == -1) { ++ /* Failed to allocate a new epid. */ ++ DBFEXIT; ++ return epid; ++ } ++ ++ /* We now have a new epid to use. Claim it. */ ++ epid_state[epid].inuse = 1; ++ ++ /* Init private data for new endpoint */ ++ if(ep_priv_create(ep, mem_flags) != 0) { ++ return -ENOMEM; ++ } ++ ep_priv = ep->hcpriv; ++ ep_priv->epid = epid; ++ ++ devnum = usb_pipedevice(urb->pipe); ++ endpoint = usb_pipeendpoint(urb->pipe); ++ slow = (urb->dev->speed == USB_SPEED_LOW); ++ maxlen = usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe)); ++ ++ if (usb_pipetype(urb->pipe) == PIPE_CONTROL) { ++ /* We want both IN and OUT control traffic to be put on the same ++ EP/SB list. */ ++ out_traffic = 1; ++ } else { ++ out_traffic = usb_pipeout(urb->pipe); ++ } ++ ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ epid_data = IO_STATE(R_USB_EPT_DATA_ISO, valid, yes) | ++ /* FIXME: Change any to the actual port? */ ++ IO_STATE(R_USB_EPT_DATA_ISO, port, any) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, max_len, maxlen) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, ep, endpoint) | ++ IO_FIELD(R_USB_EPT_DATA_ISO, dev, devnum); ++ etrax_epid_iso_set(epid, epid_data); ++ } else { ++ epid_data = IO_STATE(R_USB_EPT_DATA, valid, yes) | ++ IO_FIELD(R_USB_EPT_DATA, low_speed, slow) | ++ /* FIXME: Change any to the actual port? */ ++ IO_STATE(R_USB_EPT_DATA, port, any) | ++ IO_FIELD(R_USB_EPT_DATA, max_len, maxlen) | ++ IO_FIELD(R_USB_EPT_DATA, ep, endpoint) | ++ IO_FIELD(R_USB_EPT_DATA, dev, devnum); ++ etrax_epid_set(epid, epid_data); ++ } ++ ++ epid_state[epid].out_traffic = out_traffic; ++ epid_state[epid].type = usb_pipetype(urb->pipe); ++ ++ tc_warn("Setting up ep:0x%x epid:%d (addr:%d endp:%d max_len:%d %s %s %s)\n", ++ (unsigned int)ep, epid, devnum, endpoint, maxlen, ++ str_type(urb->pipe), out_traffic ? "out" : "in", ++ slow ? "low" : "full"); ++ ++ /* Enable Isoc eof interrupt if we set up the first Isoc epid */ ++ if(usb_pipeisoc(urb->pipe)) { ++ isoc_epid_counter++; ++ if(isoc_epid_counter == 1) { ++ isoc_warn("Enabled Isoc eof interrupt\n"); ++ *R_USB_IRQ_MASK_SET |= IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set); ++ } ++ } ++ ++ DBFEXIT; ++ return epid; ++} ++ ++static void tc_free_epid(struct usb_host_endpoint *ep) { ++ unsigned long flags; ++ struct crisv10_ep_priv *ep_priv = ep->hcpriv; ++ int epid; ++ volatile int timeout = 10000; ++ ++ DBFENTER; ++ ++ if (ep_priv == NULL) { ++ tc_warn("Trying to free unused epid on ep:0x%x\n", (unsigned int)ep); ++ DBFEXIT; ++ return; ++ } ++ ++ epid = ep_priv->epid; ++ ++ /* Disable Isoc eof interrupt if we free the last Isoc epid */ ++ if(epid_isoc(epid)) { ++ ASSERT(isoc_epid_counter > 0); ++ isoc_epid_counter--; ++ if(isoc_epid_counter == 0) { ++ *R_USB_IRQ_MASK_SET &= ~IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set); ++ isoc_warn("Disabled Isoc eof interrupt\n"); ++ } ++ } ++ ++ /* Take lock manualy instead of in epid_x_x wrappers, ++ because we need to be polling here */ ++ spin_lock_irqsave(&etrax_epid_lock, flags); ++ ++ *R_USB_EPT_INDEX = IO_FIELD(R_USB_EPT_INDEX, value, epid); ++ nop(); ++ while((*R_USB_EPT_DATA & IO_MASK(R_USB_EPT_DATA, hold)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for epid:%d to drop hold\n", epid); ++ } ++ /* This will, among other things, set the valid field to 0. */ ++ *R_USB_EPT_DATA = 0; ++ spin_unlock_irqrestore(&etrax_epid_lock, flags); ++ ++ /* Free resource in software state info list */ ++ epid_state[epid].inuse = 0; ++ ++ /* Free private endpoint data */ ++ ep_priv_free(ep); ++ ++ DBFEXIT; ++} ++ ++static int tc_allocate_epid(void) { ++ int i; ++ DBFENTER; ++ for (i = 0; i < NBR_OF_EPIDS; i++) { ++ if (!epid_inuse(i)) { ++ DBFEXIT; ++ return i; ++ } ++ } ++ ++ tc_warn("Found no free epids\n"); ++ DBFEXIT; ++ return -1; ++} ++ ++ ++/* Wrappers around the list functions (include/linux/list.h). */ ++/* ---------------------------------------------------------- */ ++static inline int __urb_list_empty(int epid) { ++ int retval; ++ retval = list_empty(&urb_list[epid]); ++ return retval; ++} ++ ++/* Returns first urb for this epid, or NULL if list is empty. */ ++static inline struct urb *urb_list_first(int epid) { ++ unsigned long flags; ++ struct urb *first_urb = 0; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ if (!__urb_list_empty(epid)) { ++ /* Get the first urb (i.e. head->next). */ ++ urb_entry_t *urb_entry = list_entry((&urb_list[epid])->next, urb_entry_t, list); ++ first_urb = urb_entry->urb; ++ } ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return first_urb; ++} ++ ++/* Adds an urb_entry last in the list for this epid. */ ++static inline void urb_list_add(struct urb *urb, int epid, int mem_flags) { ++ unsigned long flags; ++ urb_entry_t *urb_entry = (urb_entry_t *)kmalloc(sizeof(urb_entry_t), mem_flags); ++ ASSERT(urb_entry); ++ ++ urb_entry->urb = urb; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ list_add_tail(&urb_entry->list, &urb_list[epid]); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++} ++ ++/* Search through the list for an element that contains this urb. (The list ++ is expected to be short and the one we are about to delete will often be ++ the first in the list.) ++ Should be protected by spin_locks in calling function */ ++static inline urb_entry_t *__urb_list_entry(struct urb *urb, int epid) { ++ struct list_head *entry; ++ struct list_head *tmp; ++ urb_entry_t *urb_entry; ++ ++ list_for_each_safe(entry, tmp, &urb_list[epid]) { ++ urb_entry = list_entry(entry, urb_entry_t, list); ++ ASSERT(urb_entry); ++ ASSERT(urb_entry->urb); ++ ++ if (urb_entry->urb == urb) { ++ return urb_entry; ++ } ++ } ++ return 0; ++} ++ ++/* Same function as above but for global use. Protects list by spinlock */ ++static inline urb_entry_t *urb_list_entry(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return (urb_entry); ++} ++ ++/* Delete an urb from the list. */ ++static inline void urb_list_del(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ /* Delete entry and free. */ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ list_del(&urb_entry->list); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ kfree(urb_entry); ++} ++ ++/* Move an urb to the end of the list. */ ++static inline void urb_list_move_last(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ list_del(&urb_entry->list); ++ list_add_tail(&urb_entry->list, &urb_list[epid]); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++} ++ ++/* Get the next urb in the list. */ ++static inline struct urb *urb_list_next(struct urb *urb, int epid) { ++ unsigned long flags; ++ urb_entry_t *urb_entry; ++ ++ spin_lock_irqsave(&urb_list_lock, flags); ++ urb_entry = __urb_list_entry(urb, epid); ++ ASSERT(urb_entry); ++ ++ if (urb_entry->list.next != &urb_list[epid]) { ++ struct list_head *elem = urb_entry->list.next; ++ urb_entry = list_entry(elem, urb_entry_t, list); ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return urb_entry->urb; ++ } else { ++ spin_unlock_irqrestore(&urb_list_lock, flags); ++ return NULL; ++ } ++} ++ ++struct USB_EP_Desc* create_ep(int epid, struct USB_SB_Desc* sb_desc, ++ int mem_flags) { ++ struct USB_EP_Desc *ep_desc; ++ ep_desc = (struct USB_EP_Desc *) kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(ep_desc == NULL) ++ return NULL; ++ memset(ep_desc, 0, sizeof(struct USB_EP_Desc)); ++ ++ ep_desc->hw_len = 0; ++ ep_desc->command = (IO_FIELD(USB_EP_command, epid, epid) | ++ IO_STATE(USB_EP_command, enable, yes)); ++ if(sb_desc == NULL) { ++ ep_desc->sub = 0; ++ } else { ++ ep_desc->sub = virt_to_phys(sb_desc); ++ } ++ return ep_desc; ++} ++ ++#define TT_ZOUT 0 ++#define TT_IN 1 ++#define TT_OUT 2 ++#define TT_SETUP 3 ++ ++#define CMD_EOL IO_STATE(USB_SB_command, eol, yes) ++#define CMD_INTR IO_STATE(USB_SB_command, intr, yes) ++#define CMD_FULL IO_STATE(USB_SB_command, full, yes) ++ ++/* Allocation and setup of a generic SB. Used to create SETUP, OUT and ZOUT ++ SBs. Also used by create_sb_in() to avoid same allocation procedure at two ++ places */ ++struct USB_SB_Desc* create_sb(struct USB_SB_Desc* sb_prev, int tt, void* data, ++ int datalen, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ memset(sb_desc, 0, sizeof(struct USB_SB_Desc)); ++ ++ sb_desc->command = IO_FIELD(USB_SB_command, tt, tt) | ++ IO_STATE(USB_SB_command, eot, yes); ++ ++ sb_desc->sw_len = datalen; ++ if(data != NULL) { ++ sb_desc->buf = virt_to_phys(data); ++ } else { ++ sb_desc->buf = 0; ++ } ++ if(sb_prev != NULL) { ++ sb_prev->next = virt_to_phys(sb_desc); ++ } ++ return sb_desc; ++} ++ ++/* Creates a copy of an existing SB by allocation space for it and copy ++ settings */ ++struct USB_SB_Desc* create_sb_copy(struct USB_SB_Desc* sb_orig, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = (struct USB_SB_Desc*)kmem_cache_alloc(usb_desc_cache, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ ++ memcpy(sb_desc, sb_orig, sizeof(struct USB_SB_Desc)); ++ return sb_desc; ++} ++ ++/* A specific create_sb function for creation of in SBs. This is due to ++ that datalen in In SBs shows how many packets we are expecting. It also ++ sets up the rem field to show if how many bytes we expect in last packet ++ if it's not a full one */ ++struct USB_SB_Desc* create_sb_in(struct USB_SB_Desc* sb_prev, int datalen, ++ int maxlen, int mem_flags) { ++ struct USB_SB_Desc *sb_desc; ++ sb_desc = create_sb(sb_prev, TT_IN, NULL, ++ datalen ? (datalen - 1) / maxlen + 1 : 0, mem_flags); ++ if(sb_desc == NULL) ++ return NULL; ++ sb_desc->command |= IO_FIELD(USB_SB_command, rem, datalen % maxlen); ++ return sb_desc; ++} ++ ++void set_sb_cmds(struct USB_SB_Desc *sb_desc, __u16 flags) { ++ sb_desc->command |= flags; ++} ++ ++int create_sb_for_urb(struct urb *urb, int mem_flags) { ++ int is_out = !usb_pipein(urb->pipe); ++ int type = usb_pipetype(urb->pipe); ++ int maxlen = usb_maxpacket(urb->dev, urb->pipe, is_out); ++ int buf_len = urb->transfer_buffer_length; ++ void *buf = buf_len > 0 ? urb->transfer_buffer : NULL; ++ struct USB_SB_Desc *sb_desc = NULL; ++ ++ struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv != NULL); ++ ++ switch(type) { ++ case PIPE_CONTROL: ++ /* Setup stage */ ++ sb_desc = create_sb(NULL, TT_SETUP, urb->setup_packet, 8, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ ++ /* Attach first SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ ++ if (is_out) { /* Out Control URB */ ++ /* If this Control OUT transfer has an optional data stage we add ++ an OUT token before the mandatory IN (status) token */ ++ if ((buf_len > 0) && buf) { ++ sb_desc = create_sb(sb_desc, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ ++ /* Status stage */ ++ /* The data length has to be exactly 1. This is due to a requirement ++ of the USB specification that a host must be prepared to receive ++ data in the status phase */ ++ sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } else { /* In control URB */ ++ /* Data stage */ ++ sb_desc = create_sb_in(sb_desc, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* Status stage */ ++ /* Read comment at zout_buffer declaration for an explanation to this. */ ++ sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* Set descriptor interrupt flag for in URBs so we can finish URB after ++ zout-packet has been sent */ ++ set_sb_cmds(sb_desc, CMD_INTR | CMD_FULL); ++ } ++ /* Set end-of-list flag in last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ /* Attach last SB to URB */ ++ urb_priv->last_sb = sb_desc; ++ break; ++ ++ case PIPE_BULK: ++ if (is_out) { /* Out Bulk URB */ ++ sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* The full field is set to yes, even if we don't actually check that ++ this is a full-length transfer (i.e., that transfer_buffer_length % ++ maxlen = 0). ++ Setting full prevents the USB controller from sending an empty packet ++ in that case. However, if URB_ZERO_PACKET was set we want that. */ ++ if (!(urb->transfer_flags & URB_ZERO_PACKET)) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ } else { /* In Bulk URB */ ++ sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } ++ /* Set end-of-list flag for last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ break; ++ ++ case PIPE_INTERRUPT: ++ if(is_out) { /* Out Intr URB */ ++ sb_desc = create_sb(NULL, TT_OUT, buf, buf_len, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* The full field is set to yes, even if we don't actually check that ++ this is a full-length transfer (i.e., that transfer_buffer_length % ++ maxlen = 0). ++ Setting full prevents the USB controller from sending an empty packet ++ in that case. However, if URB_ZERO_PACKET was set we want that. */ ++ if (!(urb->transfer_flags & URB_ZERO_PACKET)) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ /* Only generate TX interrupt if it's a Out URB*/ ++ set_sb_cmds(sb_desc, CMD_INTR); ++ ++ } else { /* In Intr URB */ ++ sb_desc = create_sb_in(NULL, buf_len, maxlen, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ } ++ /* Set end-of-list flag for last SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ ++ break; ++ case PIPE_ISOCHRONOUS: ++ if(is_out) { /* Out Isoc URB */ ++ int i; ++ if(urb->number_of_packets == 0) { ++ tc_err("Can't create SBs for Isoc URB with zero packets\n"); ++ return -EPIPE; ++ } ++ /* Create one SB descriptor for each packet and link them together. */ ++ for(i = 0; i < urb->number_of_packets; i++) { ++ if (urb->iso_frame_desc[i].length > 0) { ++ ++ sb_desc = create_sb(sb_desc, TT_OUT, urb->transfer_buffer + ++ urb->iso_frame_desc[i].offset, ++ urb->iso_frame_desc[i].length, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ ++ /* Check if it's a full length packet */ ++ if (urb->iso_frame_desc[i].length == ++ usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))) { ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ ++ } else { /* zero length packet */ ++ sb_desc = create_sb(sb_desc, TT_ZOUT, &zout_buffer[0], 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ set_sb_cmds(sb_desc, CMD_FULL); ++ } ++ /* Attach first SB descriptor to URB */ ++ if (i == 0) { ++ urb_priv->first_sb = sb_desc; ++ } ++ } ++ /* Set interrupt and end-of-list flags in last SB */ ++ set_sb_cmds(sb_desc, CMD_INTR | CMD_EOL); ++ /* Attach last SB descriptor to URB */ ++ urb_priv->last_sb = sb_desc; ++ tc_dbg("Created %d out SBs for Isoc URB:0x%x\n", ++ urb->number_of_packets, (unsigned int)urb); ++ } else { /* In Isoc URB */ ++ /* Actual number of packets is not relevant for periodic in traffic as ++ long as it is more than zero. Set to 1 always. */ ++ sb_desc = create_sb(sb_desc, TT_IN, NULL, 1, mem_flags); ++ if(sb_desc == NULL) ++ return -ENOMEM; ++ /* Set end-of-list flags for SB */ ++ set_sb_cmds(sb_desc, CMD_EOL); ++ ++ /* Attach SB to URB */ ++ urb_priv->first_sb = sb_desc; ++ urb_priv->last_sb = sb_desc; ++ } ++ break; ++ default: ++ tc_err("Unknown pipe-type\n"); ++ return -EPIPE; ++ break; ++ } ++ return 0; ++} ++ ++int init_intr_urb(struct urb *urb, int mem_flags) { ++ struct crisv10_urb_priv *urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ struct USB_EP_Desc* ep_desc; ++ int interval; ++ int i; ++ int ep_count; ++ ++ ASSERT(urb_priv != NULL); ++ ASSERT(usb_pipeint(urb->pipe)); ++ /* We can't support interval longer than amount of eof descriptors in ++ TxIntrEPList */ ++ if(urb->interval > MAX_INTR_INTERVAL) { ++ tc_err("Interrupt interval %dms too big (max: %dms)\n", urb->interval, ++ MAX_INTR_INTERVAL); ++ return -EINVAL; ++ } ++ ++ /* We assume that the SB descriptors already have been setup */ ++ ASSERT(urb_priv->first_sb != NULL); ++ ++ /* Round of the interval to 2^n, it is obvious that this code favours ++ smaller numbers, but that is actually a good thing */ ++ /* FIXME: The "rounding error" for larger intervals will be quite ++ large. For in traffic this shouldn't be a problem since it will only ++ mean that we "poll" more often. */ ++ interval = urb->interval; ++ for (i = 0; interval; i++) { ++ interval = interval >> 1; ++ } ++ urb_priv->interval = 1 << (i - 1); ++ ++ /* We can only have max interval for Out Interrupt due to that we can only ++ handle one linked in EP for a certain epid in the Intr descr array at the ++ time. The USB Controller in the Etrax 100LX continues to process Intr EPs ++ so we have no way of knowing which one that caused the actual transfer if ++ we have several linked in. */ ++ if(usb_pipeout(urb->pipe)) { ++ urb_priv->interval = MAX_INTR_INTERVAL; ++ } ++ ++ /* Calculate amount of EPs needed */ ++ ep_count = MAX_INTR_INTERVAL / urb_priv->interval; ++ ++ for(i = 0; i < ep_count; i++) { ++ ep_desc = create_ep(urb_priv->epid, urb_priv->first_sb, mem_flags); ++ if(ep_desc == NULL) { ++ /* Free any descriptors that we may have allocated before failure */ ++ while(i > 0) { ++ i--; ++ kfree(urb_priv->intr_ep_pool[i]); ++ } ++ return -ENOMEM; ++ } ++ urb_priv->intr_ep_pool[i] = ep_desc; ++ } ++ urb_priv->intr_ep_pool_length = ep_count; ++ return 0; ++} ++ ++/* DMA RX/TX functions */ ++/* ----------------------- */ ++ ++static void tc_dma_init_rx_list(void) { ++ int i; ++ ++ /* Setup descriptor list except last one */ ++ for (i = 0; i < (NBR_OF_RX_DESC - 1); i++) { ++ RxDescList[i].sw_len = RX_DESC_BUF_SIZE; ++ RxDescList[i].command = 0; ++ RxDescList[i].next = virt_to_phys(&RxDescList[i + 1]); ++ RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); ++ RxDescList[i].hw_len = 0; ++ RxDescList[i].status = 0; ++ ++ /* DMA IN cache bug. (struct etrax_dma_descr has the same layout as ++ USB_IN_Desc for the relevant fields.) */ ++ prepare_rx_descriptor((struct etrax_dma_descr*)&RxDescList[i]); ++ ++ } ++ /* Special handling of last descriptor */ ++ RxDescList[i].sw_len = RX_DESC_BUF_SIZE; ++ RxDescList[i].command = IO_STATE(USB_IN_command, eol, yes); ++ RxDescList[i].next = virt_to_phys(&RxDescList[0]); ++ RxDescList[i].buf = virt_to_phys(RxBuf + (i * RX_DESC_BUF_SIZE)); ++ RxDescList[i].hw_len = 0; ++ RxDescList[i].status = 0; ++ ++ /* Setup list pointers that show progress in list */ ++ myNextRxDesc = &RxDescList[0]; ++ myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; ++ ++ flush_etrax_cache(); ++ /* Point DMA to first descriptor in list and start it */ ++ *R_DMA_CH9_FIRST = virt_to_phys(myNextRxDesc); ++ *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, start); ++} ++ ++ ++static void tc_dma_init_tx_bulk_list(void) { ++ int i; ++ volatile struct USB_EP_Desc *epDescr; ++ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ epDescr = &(TxBulkEPList[i]); ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxBulkEPList[i + 1]); ++ ++ /* Initiate two EPs, disabled and with the eol flag set. No need for any ++ preserved epid. */ ++ ++ /* The first one has the intr flag set so we get an interrupt when the DMA ++ channel is about to become disabled. */ ++ CHECK_ALIGN(&TxBulkDummyEPList[i][0]); ++ TxBulkDummyEPList[i][0].hw_len = 0; ++ TxBulkDummyEPList[i][0].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_STATE(USB_EP_command, intr, yes)); ++ TxBulkDummyEPList[i][0].sub = 0; ++ TxBulkDummyEPList[i][0].next = virt_to_phys(&TxBulkDummyEPList[i][1]); ++ ++ /* The second one. */ ++ CHECK_ALIGN(&TxBulkDummyEPList[i][1]); ++ TxBulkDummyEPList[i][1].hw_len = 0; ++ TxBulkDummyEPList[i][1].command = (IO_FIELD(USB_EP_command, epid, DUMMY_EPID) | ++ IO_STATE(USB_EP_command, eol, yes)); ++ TxBulkDummyEPList[i][1].sub = 0; ++ /* The last dummy's next pointer is the same as the current EP's next pointer. */ ++ TxBulkDummyEPList[i][1].next = virt_to_phys(&TxBulkEPList[i + 1]); ++ } ++ ++ /* Special handling of last descr in list, make list circular */ ++ epDescr = &TxBulkEPList[i]; ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxBulkEPList[0]); ++ ++ /* Init DMA sub-channel pointers to last item in each list */ ++ *R_DMA_CH8_SUB0_EP = virt_to_phys(&TxBulkEPList[i]); ++ /* No point in starting the bulk channel yet. ++ *R_DMA_CH8_SUB0_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */ ++} ++ ++static void tc_dma_init_tx_ctrl_list(void) { ++ int i; ++ volatile struct USB_EP_Desc *epDescr; ++ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ epDescr = &(TxCtrlEPList[i]); ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxCtrlEPList[i + 1]); ++ } ++ /* Special handling of last descr in list, make list circular */ ++ epDescr = &TxCtrlEPList[i]; ++ CHECK_ALIGN(epDescr); ++ epDescr->hw_len = 0; ++ epDescr->command = IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, i); ++ epDescr->sub = 0; ++ epDescr->next = virt_to_phys(&TxCtrlEPList[0]); ++ ++ /* Init DMA sub-channel pointers to last item in each list */ ++ *R_DMA_CH8_SUB1_EP = virt_to_phys(&TxCtrlEPList[i]); ++ /* No point in starting the ctrl channel yet. ++ *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB0_CMD, cmd, start); */ ++} ++ ++ ++static void tc_dma_init_tx_intr_list(void) { ++ int i; ++ ++ TxIntrSB_zout.sw_len = 1; ++ TxIntrSB_zout.next = 0; ++ TxIntrSB_zout.buf = virt_to_phys(&zout_buffer[0]); ++ TxIntrSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | ++ IO_STATE(USB_SB_command, tt, zout) | ++ IO_STATE(USB_SB_command, full, yes) | ++ IO_STATE(USB_SB_command, eot, yes) | ++ IO_STATE(USB_SB_command, eol, yes)); ++ ++ for (i = 0; i < (MAX_INTR_INTERVAL - 1); i++) { ++ CHECK_ALIGN(&TxIntrEPList[i]); ++ TxIntrEPList[i].hw_len = 0; ++ TxIntrEPList[i].command = ++ (IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, enable, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); ++ TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[i + 1]); ++ } ++ ++ /* Special handling of last descr in list, make list circular */ ++ CHECK_ALIGN(&TxIntrEPList[i]); ++ TxIntrEPList[i].hw_len = 0; ++ TxIntrEPList[i].command = ++ (IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_STATE(USB_EP_command, enable, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIntrEPList[i].sub = virt_to_phys(&TxIntrSB_zout); ++ TxIntrEPList[i].next = virt_to_phys(&TxIntrEPList[0]); ++ ++ intr_dbg("Initiated Intr EP descriptor list\n"); ++ ++ ++ /* Connect DMA 8 sub-channel 2 to first in list */ ++ *R_DMA_CH8_SUB2_EP = virt_to_phys(&TxIntrEPList[0]); ++} ++ ++static void tc_dma_init_tx_isoc_list(void) { ++ int i; ++ ++ DBFENTER; ++ ++ /* Read comment at zout_buffer declaration for an explanation to this. */ ++ TxIsocSB_zout.sw_len = 1; ++ TxIsocSB_zout.next = 0; ++ TxIsocSB_zout.buf = virt_to_phys(&zout_buffer[0]); ++ TxIsocSB_zout.command = (IO_FIELD(USB_SB_command, rem, 0) | ++ IO_STATE(USB_SB_command, tt, zout) | ++ IO_STATE(USB_SB_command, full, yes) | ++ IO_STATE(USB_SB_command, eot, yes) | ++ IO_STATE(USB_SB_command, eol, yes)); ++ ++ /* The last isochronous EP descriptor is a dummy. */ ++ for (i = 0; i < (NBR_OF_EPIDS - 1); i++) { ++ CHECK_ALIGN(&TxIsocEPList[i]); ++ TxIsocEPList[i].hw_len = 0; ++ TxIsocEPList[i].command = IO_FIELD(USB_EP_command, epid, i); ++ TxIsocEPList[i].sub = 0; ++ TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[i + 1]); ++ } ++ ++ CHECK_ALIGN(&TxIsocEPList[i]); ++ TxIsocEPList[i].hw_len = 0; ++ ++ /* Must enable the last EP descr to get eof interrupt. */ ++ TxIsocEPList[i].command = (IO_STATE(USB_EP_command, enable, yes) | ++ IO_STATE(USB_EP_command, eof, yes) | ++ IO_STATE(USB_EP_command, eol, yes) | ++ IO_FIELD(USB_EP_command, epid, INVALID_EPID)); ++ TxIsocEPList[i].sub = virt_to_phys(&TxIsocSB_zout); ++ TxIsocEPList[i].next = virt_to_phys(&TxIsocEPList[0]); ++ ++ *R_DMA_CH8_SUB3_EP = virt_to_phys(&TxIsocEPList[0]); ++ *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); ++} ++ ++static int tc_dma_init(struct usb_hcd *hcd) { ++ tc_dma_init_rx_list(); ++ tc_dma_init_tx_bulk_list(); ++ tc_dma_init_tx_ctrl_list(); ++ tc_dma_init_tx_intr_list(); ++ tc_dma_init_tx_isoc_list(); ++ ++ if (cris_request_dma(USB_TX_DMA_NBR, ++ "ETRAX 100LX built-in USB (Tx)", ++ DMA_VERBOSE_ON_ERROR, ++ dma_usb)) { ++ err("Could not allocate DMA ch 8 for USB"); ++ return -EBUSY; ++ } ++ ++ if (cris_request_dma(USB_RX_DMA_NBR, ++ "ETRAX 100LX built-in USB (Rx)", ++ DMA_VERBOSE_ON_ERROR, ++ dma_usb)) { ++ err("Could not allocate DMA ch 9 for USB"); ++ return -EBUSY; ++ } ++ ++ *R_IRQ_MASK2_SET = ++ /* Note that these interrupts are not used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub0_descr, set) | ++ /* Sub channel 1 (ctrl) descr. interrupts are used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub1_descr, set) | ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub2_descr, set) | ++ /* Sub channel 3 (isoc) descr. interrupts are used. */ ++ IO_STATE(R_IRQ_MASK2_SET, dma8_sub3_descr, set); ++ ++ /* Note that the dma9_descr interrupt is not used. */ ++ *R_IRQ_MASK2_SET = ++ IO_STATE(R_IRQ_MASK2_SET, dma9_eop, set) | ++ IO_STATE(R_IRQ_MASK2_SET, dma9_descr, set); ++ ++ if (request_irq(ETRAX_USB_RX_IRQ, tc_dma_rx_interrupt, 0, ++ "ETRAX 100LX built-in USB (Rx)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_RX_IRQ); ++ return -EBUSY; ++ } ++ ++ if (request_irq(ETRAX_USB_TX_IRQ, tc_dma_tx_interrupt, 0, ++ "ETRAX 100LX built-in USB (Tx)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_TX_IRQ); ++ return -EBUSY; ++ } ++ ++ return 0; ++} ++ ++static void tc_dma_destroy(void) { ++ free_irq(ETRAX_USB_RX_IRQ, NULL); ++ free_irq(ETRAX_USB_TX_IRQ, NULL); ++ ++ cris_free_dma(USB_TX_DMA_NBR, "ETRAX 100LX built-in USB (Tx)"); ++ cris_free_dma(USB_RX_DMA_NBR, "ETRAX 100LX built-in USB (Rx)"); ++ ++} ++ ++static void tc_dma_link_intr_urb(struct urb *urb); ++ ++/* Handle processing of Bulk, Ctrl and Intr queues */ ++static void tc_dma_process_queue(int epid) { ++ struct urb *urb; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ unsigned long flags; ++ char toggle; ++ ++ if(epid_state[epid].disabled) { ++ /* Don't process any URBs on a disabled endpoint */ ++ return; ++ } ++ ++ /* Do not disturb us while fiddling with EPs and epids */ ++ local_irq_save(flags); ++ ++ /* For bulk, Ctrl and Intr can we only have one URB active at a time for ++ a specific EP. */ ++ if(activeUrbList[epid] != NULL) { ++ /* An URB is already active on EP, skip checking queue */ ++ local_irq_restore(flags); ++ return; ++ } ++ ++ urb = urb_list_first(epid); ++ if(urb == NULL) { ++ /* No URB waiting in EP queue. Nothing do to */ ++ local_irq_restore(flags); ++ return; ++ } ++ ++ urb_priv = urb->hcpriv; ++ ASSERT(urb_priv != NULL); ++ ASSERT(urb_priv->urb_state == NOT_STARTED); ++ ASSERT(!usb_pipeisoc(urb->pipe)); ++ ++ /* Remove this URB from the queue and move it to active */ ++ activeUrbList[epid] = urb; ++ urb_list_del(urb, epid); ++ ++ urb_priv->urb_state = STARTED; ++ ++ /* Reset error counters (regardless of which direction this traffic is). */ ++ etrax_epid_clear_error(epid); ++ ++ /* Special handling of Intr EP lists */ ++ if(usb_pipeint(urb->pipe)) { ++ tc_dma_link_intr_urb(urb); ++ local_irq_restore(flags); ++ return; ++ } ++ ++ /* Software must preset the toggle bits for Bulk and Ctrl */ ++ if(usb_pipecontrol(urb->pipe)) { ++ /* Toggle bits are initialized only during setup transaction in a ++ CTRL transfer */ ++ etrax_epid_set_toggle(epid, 0, 0); ++ etrax_epid_set_toggle(epid, 1, 0); ++ } else { ++ toggle = usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), ++ usb_pipeout(urb->pipe)); ++ etrax_epid_set_toggle(epid, usb_pipeout(urb->pipe), toggle); ++ } ++ ++ tc_dbg("Added SBs from (URB:0x%x %s %s) to epid %d: %s\n", ++ (unsigned int)urb, str_dir(urb->pipe), str_type(urb->pipe), epid, ++ sblist_to_str(urb_priv->first_sb)); ++ ++ /* We start the DMA sub channel without checking if it's running or not, ++ because: ++ 1) If it's already running, issuing the start command is a nop. ++ 2) We avoid a test-and-set race condition. */ ++ switch(usb_pipetype(urb->pipe)) { ++ case PIPE_BULK: ++ /* Assert that the EP descriptor is disabled. */ ++ ASSERT(!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable))); ++ ++ /* Set up and enable the EP descriptor. */ ++ TxBulkEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ TxBulkEPList[epid].hw_len = 0; ++ TxBulkEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ /* Check if the dummy list is already with us (if several urbs were queued). */ ++ if (usb_pipein(urb->pipe) && (TxBulkEPList[epid].next != virt_to_phys(&TxBulkDummyEPList[epid][0]))) { ++ tc_dbg("Inviting dummy list to the party for urb 0x%lx, epid %d", ++ (unsigned long)urb, epid); ++ ++ /* We don't need to check if the DMA is at this EP or not before changing the ++ next pointer, since we will do it in one 32-bit write (EP descriptors are ++ 32-bit aligned). */ ++ TxBulkEPList[epid].next = virt_to_phys(&TxBulkDummyEPList[epid][0]); ++ } ++ ++ restart_dma8_sub0(); ++ ++ /* Update/restart the bulk start timer since we just started the channel.*/ ++ mod_timer(&bulk_start_timer, jiffies + BULK_START_TIMER_INTERVAL); ++ /* Update/restart the bulk eot timer since we just inserted traffic. */ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ break; ++ case PIPE_CONTROL: ++ /* Assert that the EP descriptor is disabled. */ ++ ASSERT(!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable))); ++ ++ /* Set up and enable the EP descriptor. */ ++ TxCtrlEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ TxCtrlEPList[epid].hw_len = 0; ++ TxCtrlEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ ++ *R_DMA_CH8_SUB1_CMD = IO_STATE(R_DMA_CH8_SUB1_CMD, cmd, start); ++ break; ++ } ++ local_irq_restore(flags); ++} ++ ++static void tc_dma_link_intr_urb(struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ volatile struct USB_EP_Desc *tmp_ep; ++ struct USB_EP_Desc *ep_desc; ++ int i = 0, epid; ++ int pool_idx = 0; ++ ++ ASSERT(urb_priv != NULL); ++ epid = urb_priv->epid; ++ ASSERT(urb_priv->interval > 0); ++ ASSERT(urb_priv->intr_ep_pool_length > 0); ++ ++ tmp_ep = &TxIntrEPList[0]; ++ ++ /* Only insert one EP descriptor in list for Out Intr URBs. ++ We can only handle Out Intr with interval of 128ms because ++ it's not possible to insert several Out Intr EPs because they ++ are not consumed by the DMA. */ ++ if(usb_pipeout(urb->pipe)) { ++ ep_desc = urb_priv->intr_ep_pool[0]; ++ ASSERT(ep_desc); ++ ep_desc->next = tmp_ep->next; ++ tmp_ep->next = virt_to_phys(ep_desc); ++ i++; ++ } else { ++ /* Loop through Intr EP descriptor list and insert EP for URB at ++ specified interval */ ++ do { ++ /* Each EP descriptor with eof flag sat signals a new frame */ ++ if (tmp_ep->command & IO_MASK(USB_EP_command, eof)) { ++ /* Insert a EP from URBs EP pool at correct interval */ ++ if ((i % urb_priv->interval) == 0) { ++ ep_desc = urb_priv->intr_ep_pool[pool_idx]; ++ ASSERT(ep_desc); ++ ep_desc->next = tmp_ep->next; ++ tmp_ep->next = virt_to_phys(ep_desc); ++ pool_idx++; ++ ASSERT(pool_idx <= urb_priv->intr_ep_pool_length); ++ } ++ i++; ++ } ++ tmp_ep = (struct USB_EP_Desc *)phys_to_virt(tmp_ep->next); ++ } while(tmp_ep != &TxIntrEPList[0]); ++ } ++ ++ intr_dbg("Added SBs to intr epid %d: %s interval:%d (%d EP)\n", epid, ++ sblist_to_str(urb_priv->first_sb), urb_priv->interval, pool_idx); ++ ++ /* We start the DMA sub channel without checking if it's running or not, ++ because: ++ 1) If it's already running, issuing the start command is a nop. ++ 2) We avoid a test-and-set race condition. */ ++ *R_DMA_CH8_SUB2_CMD = IO_STATE(R_DMA_CH8_SUB2_CMD, cmd, start); ++} ++ ++static void tc_dma_process_isoc_urb(struct urb *urb) { ++ unsigned long flags; ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ int epid; ++ ++ /* Do not disturb us while fiddling with EPs and epids */ ++ local_irq_save(flags); ++ ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->first_sb); ++ epid = urb_priv->epid; ++ ++ if(activeUrbList[epid] == NULL) { ++ /* EP is idle, so make this URB active */ ++ activeUrbList[epid] = urb; ++ urb_list_del(urb, epid); ++ ASSERT(TxIsocEPList[epid].sub == 0); ++ ASSERT(!(TxIsocEPList[epid].command & ++ IO_STATE(USB_EP_command, enable, yes))); ++ ++ /* Differentiate between In and Out Isoc. Because In SBs are not consumed*/ ++ if(usb_pipein(urb->pipe)) { ++ /* Each EP for In Isoc will have only one SB descriptor, setup when ++ submitting the first active urb. We do it here by copying from URBs ++ pre-allocated SB. */ ++ memcpy((void *)&(TxIsocSBList[epid]), urb_priv->first_sb, ++ sizeof(TxIsocSBList[epid])); ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(&(TxIsocSBList[epid])); ++ } else { ++ /* For Out Isoc we attach the pre-allocated list of SBs for the URB */ ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ ++ isoc_dbg("Attached first URB:0x%x[%d] to epid:%d first_sb:0x%x" ++ " last_sb::0x%x\n", ++ (unsigned int)urb, urb_priv->urb_num, epid, ++ (unsigned int)(urb_priv->first_sb), ++ (unsigned int)(urb_priv->last_sb)); ++ } ++ ++ if (urb->transfer_flags & URB_ISO_ASAP) { ++ /* The isoc transfer should be started as soon as possible. The ++ start_frame field is a return value if URB_ISO_ASAP was set. Comparing ++ R_USB_FM_NUMBER with a USB Chief trace shows that the first isoc IN ++ token is sent 2 frames later. I'm not sure how this affects usage of ++ the start_frame field by the device driver, or how it affects things ++ when USB_ISO_ASAP is not set, so therefore there's no compensation for ++ the 2 frame "lag" here. */ ++ urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff); ++ TxIsocEPList[epid].command |= IO_STATE(USB_EP_command, enable, yes); ++ urb_priv->urb_state = STARTED; ++ isoc_dbg("URB_ISO_ASAP set, urb->start_frame set to %d\n", ++ urb->start_frame); ++ } else { ++ /* Not started yet. */ ++ urb_priv->urb_state = NOT_STARTED; ++ isoc_warn("urb_priv->urb_state set to NOT_STARTED for URB:0x%x\n", ++ (unsigned int)urb); ++ } ++ ++ } else { ++ /* An URB is already active on the EP. Leave URB in queue and let ++ finish_isoc_urb process it after current active URB */ ++ ASSERT(TxIsocEPList[epid].sub != 0); ++ ++ if(usb_pipein(urb->pipe)) { ++ /* Because there already is a active In URB on this epid we do nothing ++ and the finish_isoc_urb() function will handle switching to next URB*/ ++ ++ } else { /* For Out Isoc, insert new URBs traffic last in SB-list. */ ++ struct USB_SB_Desc *temp_sb_desc; ++ ++ /* Set state STARTED to all Out Isoc URBs added to SB list because we ++ don't know how many of them that are finished before descr interrupt*/ ++ urb_priv->urb_state = STARTED; ++ ++ /* Find end of current SB list by looking for SB with eol flag sat */ ++ temp_sb_desc = phys_to_virt(TxIsocEPList[epid].sub); ++ while ((temp_sb_desc->command & IO_MASK(USB_SB_command, eol)) != ++ IO_STATE(USB_SB_command, eol, yes)) { ++ ASSERT(temp_sb_desc->next); ++ temp_sb_desc = phys_to_virt(temp_sb_desc->next); ++ } ++ ++ isoc_dbg("Appended URB:0x%x[%d] (first:0x%x last:0x%x) to epid:%d" ++ " sub:0x%x eol:0x%x\n", ++ (unsigned int)urb, urb_priv->urb_num, ++ (unsigned int)(urb_priv->first_sb), ++ (unsigned int)(urb_priv->last_sb), epid, ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)temp_sb_desc); ++ ++ /* Next pointer must be set before eol is removed. */ ++ temp_sb_desc->next = virt_to_phys(urb_priv->first_sb); ++ /* Clear the previous end of list flag since there is a new in the ++ added SB descriptor list. */ ++ temp_sb_desc->command &= ~IO_MASK(USB_SB_command, eol); ++ ++ if (!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { ++ __u32 epid_data; ++ /* 8.8.5 in Designer's Reference says we should check for and correct ++ any errors in the EP here. That should not be necessary if ++ epid_attn is handled correctly, so we assume all is ok. */ ++ epid_data = etrax_epid_iso_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) != ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ isoc_err("Disabled Isoc EP with error:%d on epid:%d when appending" ++ " URB:0x%x[%d]\n", ++ IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data), epid, ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ ++ /* The SB list was exhausted. */ ++ if (virt_to_phys(urb_priv->last_sb) != TxIsocEPList[epid].sub) { ++ /* The new sublist did not get processed before the EP was ++ disabled. Setup the EP again. */ ++ ++ if(virt_to_phys(temp_sb_desc) == TxIsocEPList[epid].sub) { ++ isoc_dbg("EP for epid:%d stoped at SB:0x%x before newly inserted" ++ ", restarting from this URBs SB:0x%x\n", ++ epid, (unsigned int)temp_sb_desc, ++ (unsigned int)(urb_priv->first_sb)); ++ TxIsocEPList[epid].hw_len = 0; ++ TxIsocEPList[epid].sub = virt_to_phys(urb_priv->first_sb); ++ urb->start_frame = (*R_USB_FM_NUMBER & 0x7ff); ++ /* Enable the EP again so data gets processed this time */ ++ TxIsocEPList[epid].command |= ++ IO_STATE(USB_EP_command, enable, yes); ++ ++ } else { ++ /* The EP has been disabled but not at end this URB (god knows ++ where). This should generate an epid_attn so we should not be ++ here */ ++ isoc_warn("EP was disabled on sb:0x%x before SB list for" ++ " URB:0x%x[%d] got processed\n", ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ } else { ++ /* This might happend if we are slow on this function and isn't ++ an error. */ ++ isoc_dbg("EP was disabled and finished with SBs from appended" ++ " URB:0x%x[%d]\n", (unsigned int)urb, urb_priv->urb_num); ++ } ++ } ++ } ++ } ++ ++ /* Start the DMA sub channel */ ++ *R_DMA_CH8_SUB3_CMD = IO_STATE(R_DMA_CH8_SUB3_CMD, cmd, start); ++ ++ local_irq_restore(flags); ++} ++ ++static void tc_dma_unlink_intr_urb(struct urb *urb) { ++ struct crisv10_urb_priv *urb_priv = urb->hcpriv; ++ volatile struct USB_EP_Desc *first_ep; /* First EP in the list. */ ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ volatile struct USB_EP_Desc *unlink_ep; /* The one we should remove from ++ the list. */ ++ int count = 0; ++ volatile int timeout = 10000; ++ int epid; ++ ++ /* Read 8.8.4 in Designer's Reference, "Removing an EP Descriptor from the ++ List". */ ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->intr_ep_pool_length > 0); ++ epid = urb_priv->epid; ++ ++ /* First disable all Intr EPs belonging to epid for this URB */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* Disable EP */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ ++ /* Now unlink all EPs belonging to this epid from Descr list */ ++ first_ep = &TxIntrEPList[0]; ++ curr_ep = first_ep; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if (IO_EXTRACT(USB_EP_command, epid, next_ep->command) == epid) { ++ /* This is the one we should unlink. */ ++ unlink_ep = next_ep; ++ ++ /* Actually unlink the EP from the DMA list. */ ++ curr_ep->next = unlink_ep->next; ++ ++ /* Wait until the DMA is no longer at this descriptor. */ ++ while((*R_DMA_CH8_SUB2_EP == virt_to_phys(unlink_ep)) && ++ (timeout-- > 0)); ++ if(timeout == 0) { ++ warn("Timeout while waiting for DMA-TX-Intr to leave unlink EP\n"); ++ } ++ ++ count++; ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != first_ep); ++ ++ if(count != urb_priv->intr_ep_pool_length) { ++ intr_warn("Unlinked %d of %d Intr EPs for URB:0x%x[%d]\n", count, ++ urb_priv->intr_ep_pool_length, (unsigned int)urb, ++ urb_priv->urb_num); ++ } else { ++ intr_dbg("Unlinked %d of %d interrupt EPs for URB:0x%x\n", count, ++ urb_priv->intr_ep_pool_length, (unsigned int)urb); ++ } ++} ++ ++static void check_finished_bulk_tx_epids(struct usb_hcd *hcd, ++ int timer) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ __u32 epid_data; ++ ++ /* Protect TxEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ /* A finished EP descriptor is disabled and has a valid sub pointer */ ++ if (!(TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) && ++ (TxBulkEPList[epid].sub != 0)) { ++ ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ /* Sanity checks */ ++ ASSERT(urb); ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Only handle finished out Bulk EPs here, ++ and let RX interrupt take care of the rest */ ++ if(!epid_out_traffic(epid)) { ++ continue; ++ } ++ ++ if(timer) { ++ tc_warn("Found finished %s Bulk epid:%d URB:0x%x[%d] from timeout\n", ++ epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb, ++ urb_priv->urb_num); ++ } else { ++ tc_dbg("Found finished %s Bulk epid:%d URB:0x%x[%d] from interrupt\n", ++ epid_out_traffic(epid) ? "Out" : "In", epid, (unsigned int)urb, ++ urb_priv->urb_num); ++ } ++ ++ if(urb_priv->urb_state == UNLINK) { ++ /* This Bulk URB is requested to be unlinked, that means that the EP ++ has been disabled and we might not have sent all data */ ++ tc_finish_urb(hcd, urb, urb->status); ++ continue; ++ } ++ ++ ASSERT(urb_priv->urb_state == STARTED); ++ if (phys_to_virt(TxBulkEPList[epid].sub) != urb_priv->last_sb) { ++ tc_err("Endpoint got disabled before reaching last sb\n"); ++ } ++ ++ epid_data = etrax_epid_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) == ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ /* This means that the endpoint has no error, is disabled ++ and had inserted traffic, i.e. transfer successfully completed. */ ++ tc_finish_urb(hcd, urb, 0); ++ } else { ++ /* Shouldn't happen. We expect errors to be caught by epid ++ attention. */ ++ tc_err("Found disabled bulk EP desc (epid:%d error:%d)\n", ++ epid, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data)); ++ } ++ } else { ++ tc_dbg("Ignoring In Bulk epid:%d, let RX interrupt handle it\n", epid); ++ } ++ } ++ ++ local_irq_restore(flags); ++} ++ ++static void check_finished_ctrl_tx_epids(struct usb_hcd *hcd) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ __u32 epid_data; ++ ++ /* Protect TxEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if(epid == DUMMY_EPID) ++ continue; ++ ++ /* A finished EP descriptor is disabled and has a valid sub pointer */ ++ if (!(TxCtrlEPList[epid].command & IO_MASK(USB_EP_command, enable)) && ++ (TxCtrlEPList[epid].sub != 0)) { ++ ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ ++ if(urb == NULL) { ++ tc_warn("Found finished Ctrl epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ /* Sanity checks */ ++ ASSERT(usb_pipein(urb->pipe)); ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ if (phys_to_virt(TxCtrlEPList[epid].sub) != urb_priv->last_sb) { ++ tc_err("Endpoint got disabled before reaching last sb\n"); ++ } ++ ++ epid_data = etrax_epid_get(epid); ++ if (IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data) == ++ IO_STATE_VALUE(R_USB_EPT_DATA, error_code, no_error)) { ++ /* This means that the endpoint has no error, is disabled ++ and had inserted traffic, i.e. transfer successfully completed. */ ++ ++ /* Check if RX-interrupt for In Ctrl has been processed before ++ finishing the URB */ ++ if(urb_priv->ctrl_rx_done) { ++ tc_dbg("Finishing In Ctrl URB:0x%x[%d] in tx_interrupt\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ tc_finish_urb(hcd, urb, 0); ++ } else { ++ /* If we get zout descriptor interrupt before RX was done for a ++ In Ctrl transfer, then we flag that and it will be finished ++ in the RX-Interrupt */ ++ urb_priv->ctrl_zout_done = 1; ++ tc_dbg("Got zout descr interrupt before RX interrupt\n"); ++ } ++ } else { ++ /* Shouldn't happen. We expect errors to be caught by epid ++ attention. */ ++ tc_err("Found disabled Ctrl EP desc (epid:%d URB:0x%x[%d]) error_code:%d\n", epid, (unsigned int)urb, urb_priv->urb_num, IO_EXTRACT(R_USB_EPT_DATA, error_code, epid_data)); ++ __dump_ep_desc(&(TxCtrlEPList[epid])); ++ __dump_ept_data(epid); ++ } ++ } ++ } ++ local_irq_restore(flags); ++} ++ ++/* This function goes through all epids that are setup for Out Isoc transfers ++ and marks (isoc_out_done) all queued URBs that the DMA has finished ++ transfer for. ++ No URB completetion is done here to make interrupt routine return quickly. ++ URBs are completed later with help of complete_isoc_bottom_half() that ++ becomes schedules when this functions is finished. */ ++static void check_finished_isoc_tx_epids(void) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ struct USB_SB_Desc* sb_desc; ++ int epid_done; ++ ++ /* Protect TxIsocEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (TxIsocEPList[epid].sub == 0 || epid == INVALID_EPID || ++ !epid_out_traffic(epid)) { ++ /* Nothing here to see. */ ++ continue; ++ } ++ ASSERT(epid_inuse(epid)); ++ ASSERT(epid_isoc(epid)); ++ ++ sb_desc = phys_to_virt(TxIsocEPList[epid].sub); ++ /* Find the last descriptor of the currently active URB for this ep. ++ This is the first descriptor in the sub list marked for a descriptor ++ interrupt. */ ++ while (sb_desc && !IO_EXTRACT(USB_SB_command, intr, sb_desc->command)) { ++ sb_desc = sb_desc->next ? phys_to_virt(sb_desc->next) : 0; ++ } ++ ASSERT(sb_desc); ++ ++ isoc_dbg("Descr IRQ checking epid:%d sub:0x%x intr:0x%x\n", ++ epid, (unsigned int)phys_to_virt(TxIsocEPList[epid].sub), ++ (unsigned int)sb_desc); ++ ++ urb = activeUrbList[epid]; ++ if(urb == NULL) { ++ isoc_err("Isoc Descr irq on epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ epid_done = 0; ++ while(urb && !epid_done) { ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->urb_state == STARTED || ++ urb_priv->urb_state == UNLINK); ++ ++ if (sb_desc != urb_priv->last_sb) { ++ /* This urb has been sent. */ ++ urb_priv->isoc_out_done = 1; ++ ++ } else { /* Found URB that has last_sb as the interrupt reason */ ++ ++ /* Check if EP has been disabled, meaning that all transfers are done*/ ++ if(!(TxIsocEPList[epid].command & IO_MASK(USB_EP_command, enable))) { ++ ASSERT((sb_desc->command & IO_MASK(USB_SB_command, eol)) == ++ IO_STATE(USB_SB_command, eol, yes)); ++ ASSERT(sb_desc->next == 0); ++ urb_priv->isoc_out_done = 1; ++ } else { ++ isoc_dbg("Skipping URB:0x%x[%d] because EP not disabled yet\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ /* Stop looking any further in queue */ ++ epid_done = 1; ++ } ++ ++ if (!epid_done) { ++ if(urb == activeUrbList[epid]) { ++ urb = urb_list_first(epid); ++ } else { ++ urb = urb_list_next(urb, epid); ++ } ++ } ++ } /* END: while(urb && !epid_done) */ ++ } ++ ++ local_irq_restore(flags); ++} ++ ++ ++/* This is where the Out Isoc URBs are realy completed. This function is ++ scheduled from tc_dma_tx_interrupt() when one or more Out Isoc transfers ++ are done. This functions completes all URBs earlier marked with ++ isoc_out_done by fast interrupt routine check_finished_isoc_tx_epids() */ ++ ++static void complete_isoc_bottom_half(void *data) { ++ struct crisv10_isoc_complete_data *comp_data; ++ struct usb_iso_packet_descriptor *packet; ++ struct crisv10_urb_priv * urb_priv; ++ unsigned long flags; ++ struct urb* urb; ++ int epid_done; ++ int epid; ++ int i; ++ ++ comp_data = (struct crisv10_isoc_complete_data*)data; ++ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS - 1; epid++) { ++ if(!epid_inuse(epid) || !epid_isoc(epid) || !epid_out_traffic(epid) || epid == DUMMY_EPID) { ++ /* Only check valid Out Isoc epids */ ++ continue; ++ } ++ ++ isoc_dbg("Isoc bottom-half checking epid:%d, sub:0x%x\n", epid, ++ (unsigned int)phys_to_virt(TxIsocEPList[epid].sub)); ++ ++ /* The descriptor interrupt handler has marked all transmitted Out Isoc ++ URBs with isoc_out_done. Now we traverse all epids and for all that ++ have out Isoc traffic we traverse its URB list and complete the ++ transmitted URBs. */ ++ epid_done = 0; ++ while (!epid_done) { ++ ++ /* Get the active urb (if any) */ ++ urb = activeUrbList[epid]; ++ if (urb == 0) { ++ isoc_dbg("No active URB on epid:%d anymore\n", epid); ++ epid_done = 1; ++ continue; ++ } ++ ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ if (!(urb_priv->isoc_out_done)) { ++ /* We have reached URB that isn't flaged done yet, stop traversing. */ ++ isoc_dbg("Stoped traversing Out Isoc URBs on epid:%d" ++ " before not yet flaged URB:0x%x[%d]\n", ++ epid, (unsigned int)urb, urb_priv->urb_num); ++ epid_done = 1; ++ continue; ++ } ++ ++ /* This urb has been sent. */ ++ isoc_dbg("Found URB:0x%x[%d] that is flaged isoc_out_done\n", ++ (unsigned int)urb, urb_priv->urb_num); ++ ++ /* Set ok on transfered packets for this URB and finish it */ ++ for (i = 0; i < urb->number_of_packets; i++) { ++ packet = &urb->iso_frame_desc[i]; ++ packet->status = 0; ++ packet->actual_length = packet->length; ++ } ++ urb_priv->isoc_packet_counter = urb->number_of_packets; ++ tc_finish_urb(comp_data->hcd, urb, 0); ++ ++ } /* END: while(!epid_done) */ ++ } /* END: for(epid...) */ ++ ++ local_irq_restore(flags); ++ kmem_cache_free(isoc_compl_cache, comp_data); ++} ++ ++ ++static void check_finished_intr_tx_epids(struct usb_hcd *hcd) { ++ unsigned long flags; ++ int epid; ++ struct urb *urb; ++ struct crisv10_urb_priv * urb_priv; ++ volatile struct USB_EP_Desc *curr_ep; /* Current EP, the iterator. */ ++ volatile struct USB_EP_Desc *next_ep; /* The EP after current. */ ++ ++ /* Protect TxintrEPList */ ++ local_irq_save(flags); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if(!epid_inuse(epid) || !epid_intr(epid) || !epid_out_traffic(epid)) { ++ /* Nothing to see on this epid. Only check valid Out Intr epids */ ++ continue; ++ } ++ ++ urb = activeUrbList[epid]; ++ if(urb == 0) { ++ intr_warn("Found Out Intr epid:%d with no active URB\n", epid); ++ continue; ++ } ++ ++ /* Sanity check. */ ++ ASSERT(usb_pipetype(urb->pipe) == PIPE_INTERRUPT); ++ ASSERT(usb_pipeout(urb->pipe)); ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ++ /* Go through EPs between first and second sof-EP. It's here Out Intr EPs ++ are inserted.*/ ++ curr_ep = &TxIntrEPList[0]; ++ do { ++ next_ep = (struct USB_EP_Desc *)phys_to_virt(curr_ep->next); ++ if(next_ep == urb_priv->intr_ep_pool[0]) { ++ /* We found the Out Intr EP for this epid */ ++ ++ /* Disable it so it doesn't get processed again */ ++ next_ep->command &= ~IO_MASK(USB_EP_command, enable); ++ ++ /* Finish the active Out Intr URB with status OK */ ++ tc_finish_urb(hcd, urb, 0); ++ } ++ curr_ep = phys_to_virt(curr_ep->next); ++ } while (curr_ep != &TxIntrEPList[1]); ++ ++ } ++ local_irq_restore(flags); ++} ++ ++/* Interrupt handler for DMA8/IRQ24 with subchannels (called from hardware intr) */ ++static irqreturn_t tc_dma_tx_interrupt(int irq, void *vhc) { ++ struct usb_hcd *hcd = (struct usb_hcd*)vhc; ++ ASSERT(hcd); ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub0_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB0_CLR_INTR = IO_STATE(R_DMA_CH8_SUB0_CLR_INTR, clr_descr, do); ++ restart_dma8_sub0(); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub1_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB1_CLR_INTR = IO_STATE(R_DMA_CH8_SUB1_CLR_INTR, clr_descr, do); ++ check_finished_ctrl_tx_epids(hcd); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub2_descr)) { ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB2_CLR_INTR = IO_STATE(R_DMA_CH8_SUB2_CLR_INTR, clr_descr, do); ++ check_finished_intr_tx_epids(hcd); ++ } ++ ++ if (*R_IRQ_READ2 & IO_MASK(R_IRQ_READ2, dma8_sub3_descr)) { ++ struct crisv10_isoc_complete_data* comp_data; ++ ++ /* Flag done Out Isoc for later completion */ ++ check_finished_isoc_tx_epids(); ++ ++ /* Clear this interrupt */ ++ *R_DMA_CH8_SUB3_CLR_INTR = IO_STATE(R_DMA_CH8_SUB3_CLR_INTR, clr_descr, do); ++ /* Schedule bottom half of Out Isoc completion function. This function ++ finishes the URBs marked with isoc_out_done */ ++ comp_data = (struct crisv10_isoc_complete_data*) ++ kmem_cache_alloc(isoc_compl_cache, SLAB_ATOMIC); ++ ASSERT(comp_data != NULL); ++ comp_data ->hcd = hcd; ++ ++ INIT_WORK(&comp_data->usb_bh, complete_isoc_bottom_half, comp_data); ++ schedule_work(&comp_data->usb_bh); ++ } ++ ++ return IRQ_HANDLED; ++} ++ ++/* Interrupt handler for DMA9/IRQ25 (called from hardware intr) */ ++static irqreturn_t tc_dma_rx_interrupt(int irq, void *vhc) { ++ unsigned long flags; ++ struct urb *urb; ++ struct usb_hcd *hcd = (struct usb_hcd*)vhc; ++ struct crisv10_urb_priv *urb_priv; ++ int epid = 0; ++ int real_error; ++ ++ ASSERT(hcd); ++ ++ /* Clear this interrupt. */ ++ *R_DMA_CH9_CLR_INTR = IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, do); ++ ++ /* Custom clear interrupt for this interrupt */ ++ /* The reason we cli here is that we call the driver's callback functions. */ ++ local_irq_save(flags); ++ ++ /* Note that this while loop assumes that all packets span only ++ one rx descriptor. */ ++ while(myNextRxDesc->status & IO_MASK(USB_IN_status, eop)) { ++ epid = IO_EXTRACT(USB_IN_status, epid, myNextRxDesc->status); ++ /* Get the active URB for this epid */ ++ urb = activeUrbList[epid]; ++ ++ ASSERT(epid_inuse(epid)); ++ if (!urb) { ++ dma_err("No urb for epid %d in rx interrupt\n", epid); ++ goto skip_out; ++ } ++ ++ /* Check if any errors on epid */ ++ real_error = 0; ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, error)) { ++ __u32 r_usb_ept_data; ++ ++ if (usb_pipeisoc(urb->pipe)) { ++ r_usb_ept_data = etrax_epid_iso_get(epid); ++ if((r_usb_ept_data & IO_MASK(R_USB_EPT_DATA_ISO, valid)) && ++ (IO_EXTRACT(R_USB_EPT_DATA_ISO, error_code, r_usb_ept_data) == 0) && ++ (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata))) { ++ /* Not an error, just a failure to receive an expected iso ++ in packet in this frame. This is not documented ++ in the designers reference. Continue processing. ++ */ ++ } else real_error = 1; ++ } else real_error = 1; ++ } ++ ++ if(real_error) { ++ dma_err("Error in RX descr on epid:%d for URB 0x%x", ++ epid, (unsigned int)urb); ++ dump_ept_data(epid); ++ dump_in_desc(myNextRxDesc); ++ goto skip_out; ++ } ++ ++ urb_priv = (struct crisv10_urb_priv *)urb->hcpriv; ++ ASSERT(urb_priv); ++ ASSERT(urb_priv->urb_state == STARTED || ++ urb_priv->urb_state == UNLINK); ++ ++ if ((usb_pipetype(urb->pipe) == PIPE_BULK) || ++ (usb_pipetype(urb->pipe) == PIPE_CONTROL) || ++ (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) { ++ ++ /* We get nodata for empty data transactions, and the rx descriptor's ++ hw_len field is not valid in that case. No data to copy in other ++ words. */ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { ++ /* No data to copy */ ++ } else { ++ /* ++ dma_dbg("Processing RX for URB:0x%x epid:%d (data:%d ofs:%d)\n", ++ (unsigned int)urb, epid, myNextRxDesc->hw_len, ++ urb_priv->rx_offset); ++ */ ++ /* Only copy data if URB isn't flaged to be unlinked*/ ++ if(urb_priv->urb_state != UNLINK) { ++ /* Make sure the data fits in the buffer. */ ++ if(urb_priv->rx_offset + myNextRxDesc->hw_len ++ <= urb->transfer_buffer_length) { ++ ++ /* Copy the data to URBs buffer */ ++ memcpy(urb->transfer_buffer + urb_priv->rx_offset, ++ phys_to_virt(myNextRxDesc->buf), myNextRxDesc->hw_len); ++ urb_priv->rx_offset += myNextRxDesc->hw_len; ++ } else { ++ /* Signal overflow when returning URB */ ++ urb->status = -EOVERFLOW; ++ tc_finish_urb_later(hcd, urb, urb->status); ++ } ++ } ++ } ++ ++ /* Check if it was the last packet in the transfer */ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, eot)) { ++ /* Special handling for In Ctrl URBs. */ ++ if(usb_pipecontrol(urb->pipe) && usb_pipein(urb->pipe) && ++ !(urb_priv->ctrl_zout_done)) { ++ /* Flag that RX part of Ctrl transfer is done. Because zout descr ++ interrupt hasn't happend yet will the URB be finished in the ++ TX-Interrupt. */ ++ urb_priv->ctrl_rx_done = 1; ++ tc_dbg("Not finishing In Ctrl URB:0x%x from rx_interrupt, waiting" ++ " for zout\n", (unsigned int)urb); ++ } else { ++ tc_finish_urb(hcd, urb, 0); ++ } ++ } ++ } else { /* ISOC RX */ ++ /* ++ isoc_dbg("Processing RX for epid:%d (URB:0x%x) ISOC pipe\n", ++ epid, (unsigned int)urb); ++ */ ++ ++ struct usb_iso_packet_descriptor *packet; ++ ++ if (urb_priv->urb_state == UNLINK) { ++ isoc_warn("Ignoring Isoc Rx data for urb being unlinked.\n"); ++ goto skip_out; ++ } else if (urb_priv->urb_state == NOT_STARTED) { ++ isoc_err("What? Got Rx data for Isoc urb that isn't started?\n"); ++ goto skip_out; ++ } ++ ++ packet = &urb->iso_frame_desc[urb_priv->isoc_packet_counter]; ++ ASSERT(packet); ++ packet->status = 0; ++ ++ if (myNextRxDesc->status & IO_MASK(USB_IN_status, nodata)) { ++ /* We get nodata for empty data transactions, and the rx descriptor's ++ hw_len field is not valid in that case. We copy 0 bytes however to ++ stay in synch. */ ++ packet->actual_length = 0; ++ } else { ++ packet->actual_length = myNextRxDesc->hw_len; ++ /* Make sure the data fits in the buffer. */ ++ ASSERT(packet->actual_length <= packet->length); ++ memcpy(urb->transfer_buffer + packet->offset, ++ phys_to_virt(myNextRxDesc->buf), packet->actual_length); ++ if(packet->actual_length > 0) ++ isoc_dbg("Copied %d bytes, packet %d for URB:0x%x[%d]\n", ++ packet->actual_length, urb_priv->isoc_packet_counter, ++ (unsigned int)urb, urb_priv->urb_num); ++ } ++ ++ /* Increment the packet counter. */ ++ urb_priv->isoc_packet_counter++; ++ ++ /* Note that we don't care about the eot field in the rx descriptor's ++ status. It will always be set for isoc traffic. */ ++ if (urb->number_of_packets == urb_priv->isoc_packet_counter) { ++ /* Complete the urb with status OK. */ ++ tc_finish_urb(hcd, urb, 0); ++ } ++ } ++ ++ skip_out: ++ myNextRxDesc->status = 0; ++ myNextRxDesc->command |= IO_MASK(USB_IN_command, eol); ++ myLastRxDesc->command &= ~IO_MASK(USB_IN_command, eol); ++ myLastRxDesc = myNextRxDesc; ++ myNextRxDesc = phys_to_virt(myNextRxDesc->next); ++ flush_etrax_cache(); ++ *R_DMA_CH9_CMD = IO_STATE(R_DMA_CH9_CMD, cmd, restart); ++ } ++ ++ local_irq_restore(flags); ++ ++ return IRQ_HANDLED; ++} ++ ++static void tc_bulk_start_timer_func(unsigned long dummy) { ++ /* We might enable an EP descriptor behind the current DMA position when ++ it's about to decide that there are no more bulk traffic and it should ++ stop the bulk channel. ++ Therefore we periodically check if the bulk channel is stopped and there ++ is an enabled bulk EP descriptor, in which case we start the bulk ++ channel. */ ++ ++ if (!(*R_DMA_CH8_SUB0_CMD & IO_MASK(R_DMA_CH8_SUB0_CMD, cmd))) { ++ int epid; ++ ++ timer_dbg("bulk_start_timer: Bulk DMA channel not running.\n"); ++ ++ for (epid = 0; epid < NBR_OF_EPIDS; epid++) { ++ if (TxBulkEPList[epid].command & IO_MASK(USB_EP_command, enable)) { ++ timer_warn("Found enabled EP for epid %d, starting bulk channel.\n", ++ epid); ++ restart_dma8_sub0(); ++ ++ /* Restart the bulk eot timer since we just started the bulk channel.*/ ++ mod_timer(&bulk_eot_timer, jiffies + BULK_EOT_TIMER_INTERVAL); ++ ++ /* No need to search any further. */ ++ break; ++ } ++ } ++ } else { ++ timer_dbg("bulk_start_timer: Bulk DMA channel running.\n"); ++ } ++} ++ ++static void tc_bulk_eot_timer_func(unsigned long dummy) { ++ struct usb_hcd *hcd = (struct usb_hcd*)dummy; ++ ASSERT(hcd); ++ /* Because of a race condition in the top half, we might miss a bulk eot. ++ This timer "simulates" a bulk eot if we don't get one for a while, ++ hopefully correcting the situation. */ ++ timer_dbg("bulk_eot_timer timed out.\n"); ++ check_finished_bulk_tx_epids(hcd, 1); ++} ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Device driver block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* Forward declarations for device driver functions */ ++static int devdrv_hcd_probe(struct device *); ++static int devdrv_hcd_remove(struct device *); ++#ifdef CONFIG_PM ++static int devdrv_hcd_suspend(struct device *, u32, u32); ++static int devdrv_hcd_resume(struct device *, u32); ++#endif /* CONFIG_PM */ ++ ++/* the device */ ++static struct platform_device *devdrv_hc_platform_device; ++ ++/* device driver interface */ ++static struct device_driver devdrv_hc_device_driver = { ++ .name = (char *) hc_name, ++ .bus = &platform_bus_type, ++ ++ .probe = devdrv_hcd_probe, ++ .remove = devdrv_hcd_remove, ++ ++#ifdef CONFIG_PM ++ .suspend = devdrv_hcd_suspend, ++ .resume = devdrv_hcd_resume, ++#endif /* CONFIG_PM */ ++}; ++ ++/* initialize the host controller and driver */ ++static int __init_or_module devdrv_hcd_probe(struct device *dev) ++{ ++ struct usb_hcd *hcd; ++ struct crisv10_hcd *crisv10_hcd; ++ int retval; ++ ++ /* Check DMA burst length */ ++ if(IO_EXTRACT(R_BUS_CONFIG, dma_burst, *R_BUS_CONFIG) != ++ IO_STATE(R_BUS_CONFIG, dma_burst, burst32)) { ++ devdrv_err("Invalid DMA burst length in Etrax 100LX," ++ " needs to be 32\n"); ++ return -EPERM; ++ } ++ ++ hcd = usb_create_hcd(&crisv10_hc_driver, dev, dev->bus_id); ++ if (!hcd) ++ return -ENOMEM; ++ ++ crisv10_hcd = hcd_to_crisv10_hcd(hcd); ++ spin_lock_init(&crisv10_hcd->lock); ++ crisv10_hcd->num_ports = num_ports(); ++ crisv10_hcd->running = 0; ++ ++ dev_set_drvdata(dev, crisv10_hcd); ++ ++ devdrv_dbg("ETRAX USB IRQs HC:%d RX:%d TX:%d\n", ETRAX_USB_HC_IRQ, ++ ETRAX_USB_RX_IRQ, ETRAX_USB_TX_IRQ); ++ ++ /* Print out chip version read from registers */ ++ int rev_maj = *R_USB_REVISION & IO_MASK(R_USB_REVISION, major); ++ int rev_min = *R_USB_REVISION & IO_MASK(R_USB_REVISION, minor); ++ if(rev_min == 0) { ++ devdrv_info("Etrax 100LX USB Revision %d v1,2\n", rev_maj); ++ } else { ++ devdrv_info("Etrax 100LX USB Revision %d v%d\n", rev_maj, rev_min); ++ } ++ ++ devdrv_info("Bulk timer interval, start:%d eot:%d\n", ++ BULK_START_TIMER_INTERVAL, ++ BULK_EOT_TIMER_INTERVAL); ++ ++ ++ /* Init root hub data structures */ ++ if(rh_init()) { ++ devdrv_err("Failed init data for Root Hub\n"); ++ retval = -ENOMEM; ++ } ++ ++ if(port_in_use(0)) { ++ if (cris_request_io_interface(if_usb_1, "ETRAX100LX USB-HCD")) { ++ printk(KERN_CRIT "usb-host: request IO interface usb1 failed"); ++ retval = -EBUSY; ++ goto out; ++ } ++ devdrv_info("Claimed interface for USB physical port 1\n"); ++ } ++ if(port_in_use(1)) { ++ if (cris_request_io_interface(if_usb_2, "ETRAX100LX USB-HCD")) { ++ /* Free first interface if second failed to be claimed */ ++ if(port_in_use(0)) { ++ cris_free_io_interface(if_usb_1); ++ } ++ printk(KERN_CRIT "usb-host: request IO interface usb2 failed"); ++ retval = -EBUSY; ++ goto out; ++ } ++ devdrv_info("Claimed interface for USB physical port 2\n"); ++ } ++ ++ /* Init transfer controller structs and locks */ ++ if((retval = tc_init(hcd)) != 0) { ++ goto out; ++ } ++ ++ /* Attach interrupt functions for DMA and init DMA controller */ ++ if((retval = tc_dma_init(hcd)) != 0) { ++ goto out; ++ } ++ ++ /* Attach the top IRQ handler for USB controller interrupts */ ++ if (request_irq(ETRAX_USB_HC_IRQ, crisv10_hcd_top_irq, 0, ++ "ETRAX 100LX built-in USB (HC)", hcd)) { ++ err("Could not allocate IRQ %d for USB", ETRAX_USB_HC_IRQ); ++ retval = -EBUSY; ++ goto out; ++ } ++ ++ /* iso_eof is only enabled when isoc traffic is running. */ ++ *R_USB_IRQ_MASK_SET = ++ /* IO_STATE(R_USB_IRQ_MASK_SET, iso_eof, set) | */ ++ IO_STATE(R_USB_IRQ_MASK_SET, bulk_eot, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, epid_attn, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, port_status, set) | ++ IO_STATE(R_USB_IRQ_MASK_SET, ctl_status, set); ++ ++ ++ crisv10_ready_wait(); ++ /* Reset the USB interface. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, reset); ++ ++ /* Designer's Reference, p. 8 - 10 says we should Initate R_USB_FM_PSTART to ++ 0x2A30 (10800), to guarantee that control traffic gets 10% of the ++ bandwidth, and periodic transfer may allocate the rest (90%). ++ This doesn't work though. ++ The value 11960 is chosen to be just after the SOF token, with a couple ++ of bit times extra for possible bit stuffing. */ ++ *R_USB_FM_PSTART = IO_FIELD(R_USB_FM_PSTART, value, 11960); ++ ++ crisv10_ready_wait(); ++ /* Configure the USB interface as a host controller. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_config); ++ ++ ++ /* Check so controller not busy before enabling ports */ ++ crisv10_ready_wait(); ++ ++ /* Enable selected USB ports */ ++ if(port_in_use(0)) { ++ *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, no); ++ } else { ++ *R_USB_PORT1_DISABLE = IO_STATE(R_USB_PORT1_DISABLE, disable, yes); ++ } ++ if(port_in_use(1)) { ++ *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, no); ++ } else { ++ *R_USB_PORT2_DISABLE = IO_STATE(R_USB_PORT2_DISABLE, disable, yes); ++ } ++ ++ crisv10_ready_wait(); ++ /* Start processing of USB traffic. */ ++ *R_USB_COMMAND = ++ IO_STATE(R_USB_COMMAND, port_sel, nop) | ++ IO_STATE(R_USB_COMMAND, port_cmd, reset) | ++ IO_STATE(R_USB_COMMAND, ctrl_cmd, host_run); ++ ++ /* Do not continue probing initialization before USB interface is done */ ++ crisv10_ready_wait(); ++ ++ /* Register our Host Controller to USB Core ++ * Finish the remaining parts of generic HCD initialization: allocate the ++ * buffers of consistent memory, register the bus ++ * and call the driver's reset() and start() routines. */ ++ retval = usb_add_hcd(hcd, ETRAX_USB_HC_IRQ, IRQF_DISABLED); ++ if (retval != 0) { ++ devdrv_err("Failed registering HCD driver\n"); ++ goto out; ++ } ++ ++ return 0; ++ ++ out: ++ devdrv_hcd_remove(dev); ++ return retval; ++} ++ ++ ++/* cleanup after the host controller and driver */ ++static int __init_or_module devdrv_hcd_remove(struct device *dev) ++{ ++ struct crisv10_hcd *crisv10_hcd = dev_get_drvdata(dev); ++ struct usb_hcd *hcd; ++ ++ if (!crisv10_hcd) ++ return 0; ++ hcd = crisv10_hcd_to_hcd(crisv10_hcd); ++ ++ ++ /* Stop USB Controller in Etrax 100LX */ ++ crisv10_hcd_reset(hcd); ++ ++ usb_remove_hcd(hcd); ++ devdrv_dbg("Removed HCD from USB Core\n"); ++ ++ /* Free USB Controller IRQ */ ++ free_irq(ETRAX_USB_HC_IRQ, NULL); ++ ++ /* Free resources */ ++ tc_dma_destroy(); ++ tc_destroy(); ++ ++ ++ if(port_in_use(0)) { ++ cris_free_io_interface(if_usb_1); ++ } ++ if(port_in_use(1)) { ++ cris_free_io_interface(if_usb_2); ++ } ++ ++ devdrv_dbg("Freed all claimed resources\n"); ++ ++ return 0; ++} ++ ++ ++#ifdef CONFIG_PM ++ ++static int devdrv_hcd_suspend(struct usb_hcd *hcd, u32 state, u32 level) ++{ ++ return 0; /* no-op for now */ ++} ++ ++static int devdrv_hcd_resume(struct usb_hcd *hcd, u32 level) ++{ ++ return 0; /* no-op for now */ ++} ++ ++#endif /* CONFIG_PM */ ++ ++ ++ ++/*************************************************************/ ++/*************************************************************/ ++/* Module block */ ++/*************************************************************/ ++/*************************************************************/ ++ ++/* register driver */ ++static int __init module_hcd_init(void) ++{ ++ ++ if (usb_disabled()) ++ return -ENODEV; ++ ++ /* Here we select enabled ports by following defines created from ++ menuconfig */ ++#ifndef CONFIG_ETRAX_USB_HOST_PORT1 ++ ports &= ~(1<<0); ++#endif ++#ifndef CONFIG_ETRAX_USB_HOST_PORT2 ++ ports &= ~(1<<1); ++#endif ++ ++ printk(KERN_INFO "%s version "VERSION" "COPYRIGHT"\n", product_desc); ++ ++ devdrv_hc_platform_device = ++ platform_device_register_simple((char *) hc_name, 0, NULL, 0); ++ ++ if (IS_ERR(devdrv_hc_platform_device)) ++ return PTR_ERR(devdrv_hc_platform_device); ++ return driver_register(&devdrv_hc_device_driver); ++ /* ++ * Note that we do not set the DMA mask for the device, ++ * i.e. we pretend that we will use PIO, since no specific ++ * allocation routines are needed for DMA buffers. This will ++ * cause the HCD buffer allocation routines to fall back to ++ * kmalloc(). ++ */ ++} ++ ++/* unregister driver */ ++static void __exit module_hcd_exit(void) ++{ ++ driver_unregister(&devdrv_hc_device_driver); ++} ++ ++ ++/* Module hooks */ ++module_init(module_hcd_init); ++module_exit(module_hcd_exit); +--- linux-2.6.19.2.orig/drivers/usb/host/hc_crisv10.h 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/usb/host/hc_crisv10.h 1970-01-01 01:00:00.000000000 +0100 +@@ -1,289 +0,0 @@ +-#ifndef __LINUX_ETRAX_USB_H +-#define __LINUX_ETRAX_USB_H +- +-#include <linux/types.h> +-#include <linux/list.h> +- +-typedef struct USB_IN_Desc { +- volatile __u16 sw_len; +- volatile __u16 command; +- volatile unsigned long next; +- volatile unsigned long buf; +- volatile __u16 hw_len; +- volatile __u16 status; +-} USB_IN_Desc_t; +- +-typedef struct USB_SB_Desc { +- volatile __u16 sw_len; +- volatile __u16 command; +- volatile unsigned long next; +- volatile unsigned long buf; +- __u32 dummy; +-} USB_SB_Desc_t; +- +-typedef struct USB_EP_Desc { +- volatile __u16 hw_len; +- volatile __u16 command; +- volatile unsigned long sub; +- volatile unsigned long next; +- __u32 dummy; +-} USB_EP_Desc_t; +- +-struct virt_root_hub { +- int devnum; +- void *urb; +- void *int_addr; +- int send; +- int interval; +- int numports; +- struct timer_list rh_int_timer; +- volatile __u16 wPortChange_1; +- volatile __u16 wPortChange_2; +- volatile __u16 prev_wPortStatus_1; +- volatile __u16 prev_wPortStatus_2; +-}; +- +-struct etrax_usb_intr_traffic { +- int sleeping; +- int error; +- struct wait_queue *wq; +-}; +- +-typedef struct etrax_usb_hc { +- struct usb_bus *bus; +- struct virt_root_hub rh; +- struct etrax_usb_intr_traffic intr; +-} etrax_hc_t; +- +-typedef enum { +- STARTED, +- NOT_STARTED, +- UNLINK, +- TRANSFER_DONE, +- WAITING_FOR_DESCR_INTR +-} etrax_usb_urb_state_t; +- +- +- +-typedef struct etrax_usb_urb_priv { +- /* The first_sb field is used for freeing all SB descriptors belonging +- to an urb. The corresponding ep descriptor's sub pointer cannot be +- used for this since the DMA advances the sub pointer as it processes +- the sb list. */ +- USB_SB_Desc_t *first_sb; +- /* The last_sb field referes to the last SB descriptor that belongs to +- this urb. This is important to know so we can free the SB descriptors +- that ranges between first_sb and last_sb. */ +- USB_SB_Desc_t *last_sb; +- +- /* The rx_offset field is used in ctrl and bulk traffic to keep track +- of the offset in the urb's transfer_buffer where incoming data should be +- copied to. */ +- __u32 rx_offset; +- +- /* Counter used in isochronous transfers to keep track of the +- number of packets received/transmitted. */ +- __u32 isoc_packet_counter; +- +- /* This field is used to pass information about the urb's current state between +- the various interrupt handlers (thus marked volatile). */ +- volatile etrax_usb_urb_state_t urb_state; +- +- /* Connection between the submitted urb and ETRAX epid number */ +- __u8 epid; +- +- /* The rx_data_list field is used for periodic traffic, to hold +- received data for later processing in the the complete_urb functions, +- where the data us copied to the urb's transfer_buffer. Basically, we +- use this intermediate storage because we don't know when it's safe to +- reuse the transfer_buffer (FIXME?). */ +- struct list_head rx_data_list; +-} etrax_urb_priv_t; +- +-/* This struct is for passing data from the top half to the bottom half. */ +-typedef struct usb_interrupt_registers +-{ +- etrax_hc_t *hc; +- __u32 r_usb_epid_attn; +- __u8 r_usb_status; +- __u16 r_usb_rh_port_status_1; +- __u16 r_usb_rh_port_status_2; +- __u32 r_usb_irq_mask_read; +- __u32 r_usb_fm_number; +- struct work_struct usb_bh; +-} usb_interrupt_registers_t; +- +-/* This struct is for passing data from the isoc top half to the isoc bottom half. */ +-typedef struct usb_isoc_complete_data +-{ +- struct urb *urb; +- struct work_struct usb_bh; +-} usb_isoc_complete_data_t; +- +-/* This struct holds data we get from the rx descriptors for DMA channel 9 +- for periodic traffic (intr and isoc). */ +-typedef struct rx_data +-{ +- void *data; +- int length; +- struct list_head list; +-} rx_data_t; +- +-typedef struct urb_entry +-{ +- struct urb *urb; +- struct list_head list; +-} urb_entry_t; +- +-/* --------------------------------------------------------------------------- +- Virtual Root HUB +- ------------------------------------------------------------------------- */ +-/* destination of request */ +-#define RH_INTERFACE 0x01 +-#define RH_ENDPOINT 0x02 +-#define RH_OTHER 0x03 +- +-#define RH_CLASS 0x20 +-#define RH_VENDOR 0x40 +- +-/* Requests: bRequest << 8 | bmRequestType */ +-#define RH_GET_STATUS 0x0080 +-#define RH_CLEAR_FEATURE 0x0100 +-#define RH_SET_FEATURE 0x0300 +-#define RH_SET_ADDRESS 0x0500 +-#define RH_GET_DESCRIPTOR 0x0680 +-#define RH_SET_DESCRIPTOR 0x0700 +-#define RH_GET_CONFIGURATION 0x0880 +-#define RH_SET_CONFIGURATION 0x0900 +-#define RH_GET_STATE 0x0280 +-#define RH_GET_INTERFACE 0x0A80 +-#define RH_SET_INTERFACE 0x0B00 +-#define RH_SYNC_FRAME 0x0C80 +-/* Our Vendor Specific Request */ +-#define RH_SET_EP 0x2000 +- +- +-/* Hub port features */ +-#define RH_PORT_CONNECTION 0x00 +-#define RH_PORT_ENABLE 0x01 +-#define RH_PORT_SUSPEND 0x02 +-#define RH_PORT_OVER_CURRENT 0x03 +-#define RH_PORT_RESET 0x04 +-#define RH_PORT_POWER 0x08 +-#define RH_PORT_LOW_SPEED 0x09 +-#define RH_C_PORT_CONNECTION 0x10 +-#define RH_C_PORT_ENABLE 0x11 +-#define RH_C_PORT_SUSPEND 0x12 +-#define RH_C_PORT_OVER_CURRENT 0x13 +-#define RH_C_PORT_RESET 0x14 +- +-/* Hub features */ +-#define RH_C_HUB_LOCAL_POWER 0x00 +-#define RH_C_HUB_OVER_CURRENT 0x01 +- +-#define RH_DEVICE_REMOTE_WAKEUP 0x00 +-#define RH_ENDPOINT_STALL 0x01 +- +-/* Our Vendor Specific feature */ +-#define RH_REMOVE_EP 0x00 +- +- +-#define RH_ACK 0x01 +-#define RH_REQ_ERR -1 +-#define RH_NACK 0x00 +- +-/* Field definitions for */ +- +-#define USB_IN_command__eol__BITNR 0 /* command macros */ +-#define USB_IN_command__eol__WIDTH 1 +-#define USB_IN_command__eol__no 0 +-#define USB_IN_command__eol__yes 1 +- +-#define USB_IN_command__intr__BITNR 3 +-#define USB_IN_command__intr__WIDTH 1 +-#define USB_IN_command__intr__no 0 +-#define USB_IN_command__intr__yes 1 +- +-#define USB_IN_status__eop__BITNR 1 /* status macros. */ +-#define USB_IN_status__eop__WIDTH 1 +-#define USB_IN_status__eop__no 0 +-#define USB_IN_status__eop__yes 1 +- +-#define USB_IN_status__eot__BITNR 5 +-#define USB_IN_status__eot__WIDTH 1 +-#define USB_IN_status__eot__no 0 +-#define USB_IN_status__eot__yes 1 +- +-#define USB_IN_status__error__BITNR 6 +-#define USB_IN_status__error__WIDTH 1 +-#define USB_IN_status__error__no 0 +-#define USB_IN_status__error__yes 1 +- +-#define USB_IN_status__nodata__BITNR 7 +-#define USB_IN_status__nodata__WIDTH 1 +-#define USB_IN_status__nodata__no 0 +-#define USB_IN_status__nodata__yes 1 +- +-#define USB_IN_status__epid__BITNR 8 +-#define USB_IN_status__epid__WIDTH 5 +- +-#define USB_EP_command__eol__BITNR 0 +-#define USB_EP_command__eol__WIDTH 1 +-#define USB_EP_command__eol__no 0 +-#define USB_EP_command__eol__yes 1 +- +-#define USB_EP_command__eof__BITNR 1 +-#define USB_EP_command__eof__WIDTH 1 +-#define USB_EP_command__eof__no 0 +-#define USB_EP_command__eof__yes 1 +- +-#define USB_EP_command__intr__BITNR 3 +-#define USB_EP_command__intr__WIDTH 1 +-#define USB_EP_command__intr__no 0 +-#define USB_EP_command__intr__yes 1 +- +-#define USB_EP_command__enable__BITNR 4 +-#define USB_EP_command__enable__WIDTH 1 +-#define USB_EP_command__enable__no 0 +-#define USB_EP_command__enable__yes 1 +- +-#define USB_EP_command__hw_valid__BITNR 5 +-#define USB_EP_command__hw_valid__WIDTH 1 +-#define USB_EP_command__hw_valid__no 0 +-#define USB_EP_command__hw_valid__yes 1 +- +-#define USB_EP_command__epid__BITNR 8 +-#define USB_EP_command__epid__WIDTH 5 +- +-#define USB_SB_command__eol__BITNR 0 /* command macros. */ +-#define USB_SB_command__eol__WIDTH 1 +-#define USB_SB_command__eol__no 0 +-#define USB_SB_command__eol__yes 1 +- +-#define USB_SB_command__eot__BITNR 1 +-#define USB_SB_command__eot__WIDTH 1 +-#define USB_SB_command__eot__no 0 +-#define USB_SB_command__eot__yes 1 +- +-#define USB_SB_command__intr__BITNR 3 +-#define USB_SB_command__intr__WIDTH 1 +-#define USB_SB_command__intr__no 0 +-#define USB_SB_command__intr__yes 1 +- +-#define USB_SB_command__tt__BITNR 4 +-#define USB_SB_command__tt__WIDTH 2 +-#define USB_SB_command__tt__zout 0 +-#define USB_SB_command__tt__in 1 +-#define USB_SB_command__tt__out 2 +-#define USB_SB_command__tt__setup 3 +- +- +-#define USB_SB_command__rem__BITNR 8 +-#define USB_SB_command__rem__WIDTH 6 +- +-#define USB_SB_command__full__BITNR 6 +-#define USB_SB_command__full__WIDTH 1 +-#define USB_SB_command__full__no 0 +-#define USB_SB_command__full__yes 1 +- +-#endif +--- linux-2.6.19.2.orig/drivers/usb/host/hc-crisv10.h 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/usb/host/hc-crisv10.h 2006-01-27 13:59:58.000000000 +0100 +@@ -0,0 +1,330 @@ ++#ifndef __LINUX_ETRAX_USB_H ++#define __LINUX_ETRAX_USB_H ++ ++#include <linux/types.h> ++#include <linux/list.h> ++ ++struct USB_IN_Desc { ++ volatile __u16 sw_len; ++ volatile __u16 command; ++ volatile unsigned long next; ++ volatile unsigned long buf; ++ volatile __u16 hw_len; ++ volatile __u16 status; ++}; ++ ++struct USB_SB_Desc { ++ volatile __u16 sw_len; ++ volatile __u16 command; ++ volatile unsigned long next; ++ volatile unsigned long buf; ++}; ++ ++struct USB_EP_Desc { ++ volatile __u16 hw_len; ++ volatile __u16 command; ++ volatile unsigned long sub; ++ volatile unsigned long next; ++}; ++ ++ ++/* Root Hub port status struct */ ++struct crisv10_rh { ++ volatile __u16 wPortChange[2]; ++ volatile __u16 wPortStatusPrev[2]; ++}; ++ ++/* HCD description */ ++struct crisv10_hcd { ++ spinlock_t lock; ++ __u8 num_ports; ++ __u8 running; ++}; ++ ++ ++/* Endpoint HC private data description */ ++struct crisv10_ep_priv { ++ int epid; ++}; ++ ++/* Additional software state info for a USB Controller epid */ ++struct etrax_epid { ++ __u8 inuse; /* !0 = setup in Etrax and used for a endpoint */ ++ __u8 disabled; /* !0 = Temporarly disabled to avoid resubmission */ ++ __u8 type; /* Setup as: PIPE_BULK, PIPE_CONTROL ... */ ++ __u8 out_traffic; /* !0 = This epid is for out traffic */ ++}; ++ ++/* Struct to hold information of scheduled later URB completion */ ++struct urb_later_data { ++ struct work_struct ws; ++ struct usb_hcd *hcd; ++ struct urb *urb; ++ int urb_num; ++ int status; ++}; ++ ++ ++typedef enum { ++ STARTED, ++ NOT_STARTED, ++ UNLINK, ++} crisv10_urb_state_t; ++ ++ ++struct crisv10_urb_priv { ++ /* Sequence number for this URB. Every new submited URB gets this from ++ a incrementing counter. Used when a URB is scheduled for later finish to ++ be sure that the intended URB hasn't already been completed (device ++ drivers has a tendency to reuse URBs once they are completed, causing us ++ to not be able to single old ones out only based on the URB pointer.) */ ++ __u32 urb_num; ++ ++ /* The first_sb field is used for freeing all SB descriptors belonging ++ to an urb. The corresponding ep descriptor's sub pointer cannot be ++ used for this since the DMA advances the sub pointer as it processes ++ the sb list. */ ++ struct USB_SB_Desc *first_sb; ++ ++ /* The last_sb field referes to the last SB descriptor that belongs to ++ this urb. This is important to know so we can free the SB descriptors ++ that ranges between first_sb and last_sb. */ ++ struct USB_SB_Desc *last_sb; ++ ++ /* The rx_offset field is used in ctrl and bulk traffic to keep track ++ of the offset in the urb's transfer_buffer where incoming data should be ++ copied to. */ ++ __u32 rx_offset; ++ ++ /* Counter used in isochronous transfers to keep track of the ++ number of packets received/transmitted. */ ++ __u32 isoc_packet_counter; ++ ++ /* Flag that marks if this Isoc Out URB has finished it's transfer. Used ++ because several URBs can be finished before list is processed */ ++ __u8 isoc_out_done; ++ ++ /* This field is used to pass information about the urb's current state ++ between the various interrupt handlers (thus marked volatile). */ ++ volatile crisv10_urb_state_t urb_state; ++ ++ /* In Ctrl transfers consist of (at least) 3 packets: SETUP, IN and ZOUT. ++ When DMA8 sub-channel 2 has processed the SB list for this sequence we ++ get a interrupt. We also get a interrupt for In transfers and which ++ one of these interrupts that comes first depends of data size and device. ++ To be sure that we have got both interrupts before we complete the URB ++ we have these to flags that shows which part that has completed. ++ We can then check when we get one of the interrupts that if the other has ++ occured it's safe for us to complete the URB, otherwise we set appropriate ++ flag and do the completion when we get the other interrupt. */ ++ volatile unsigned char ctrl_zout_done; ++ volatile unsigned char ctrl_rx_done; ++ ++ /* Connection between the submitted urb and ETRAX epid number */ ++ __u8 epid; ++ ++ /* The rx_data_list field is used for periodic traffic, to hold ++ received data for later processing in the the complete_urb functions, ++ where the data us copied to the urb's transfer_buffer. Basically, we ++ use this intermediate storage because we don't know when it's safe to ++ reuse the transfer_buffer (FIXME?). */ ++ struct list_head rx_data_list; ++ ++ ++ /* The interval time rounded up to closest 2^N */ ++ int interval; ++ ++ /* Pool of EP descriptors needed if it's a INTR transfer. ++ Amount of EPs in pool correspons to how many INTR that should ++ be inserted in TxIntrEPList (max 128, defined by MAX_INTR_INTERVAL) */ ++ struct USB_EP_Desc* intr_ep_pool[128]; ++ ++ /* The mount of EPs allocated for this INTR URB */ ++ int intr_ep_pool_length; ++ ++ /* Pointer to info struct if URB is scheduled to be finished later */ ++ struct urb_later_data* later_data; ++}; ++ ++ ++/* This struct is for passing data from the top half to the bottom half irq ++ handlers */ ++struct crisv10_irq_reg { ++ struct usb_hcd* hcd; ++ __u32 r_usb_epid_attn; ++ __u8 r_usb_status; ++ __u16 r_usb_rh_port_status_1; ++ __u16 r_usb_rh_port_status_2; ++ __u32 r_usb_irq_mask_read; ++ __u32 r_usb_fm_number; ++ struct work_struct usb_bh; ++}; ++ ++ ++/* This struct is for passing data from the isoc top half to the isoc bottom ++ half. */ ++struct crisv10_isoc_complete_data { ++ struct usb_hcd *hcd; ++ struct urb *urb; ++ struct work_struct usb_bh; ++}; ++ ++/* Entry item for URB lists for each endpint */ ++typedef struct urb_entry ++{ ++ struct urb *urb; ++ struct list_head list; ++} urb_entry_t; ++ ++/* --------------------------------------------------------------------------- ++ Virtual Root HUB ++ ------------------------------------------------------------------------- */ ++/* destination of request */ ++#define RH_INTERFACE 0x01 ++#define RH_ENDPOINT 0x02 ++#define RH_OTHER 0x03 ++ ++#define RH_CLASS 0x20 ++#define RH_VENDOR 0x40 ++ ++/* Requests: bRequest << 8 | bmRequestType */ ++#define RH_GET_STATUS 0x0080 ++#define RH_CLEAR_FEATURE 0x0100 ++#define RH_SET_FEATURE 0x0300 ++#define RH_SET_ADDRESS 0x0500 ++#define RH_GET_DESCRIPTOR 0x0680 ++#define RH_SET_DESCRIPTOR 0x0700 ++#define RH_GET_CONFIGURATION 0x0880 ++#define RH_SET_CONFIGURATION 0x0900 ++#define RH_GET_STATE 0x0280 ++#define RH_GET_INTERFACE 0x0A80 ++#define RH_SET_INTERFACE 0x0B00 ++#define RH_SYNC_FRAME 0x0C80 ++/* Our Vendor Specific Request */ ++#define RH_SET_EP 0x2000 ++ ++ ++/* Hub port features */ ++#define RH_PORT_CONNECTION 0x00 ++#define RH_PORT_ENABLE 0x01 ++#define RH_PORT_SUSPEND 0x02 ++#define RH_PORT_OVER_CURRENT 0x03 ++#define RH_PORT_RESET 0x04 ++#define RH_PORT_POWER 0x08 ++#define RH_PORT_LOW_SPEED 0x09 ++#define RH_C_PORT_CONNECTION 0x10 ++#define RH_C_PORT_ENABLE 0x11 ++#define RH_C_PORT_SUSPEND 0x12 ++#define RH_C_PORT_OVER_CURRENT 0x13 ++#define RH_C_PORT_RESET 0x14 ++ ++/* Hub features */ ++#define RH_C_HUB_LOCAL_POWER 0x00 ++#define RH_C_HUB_OVER_CURRENT 0x01 ++ ++#define RH_DEVICE_REMOTE_WAKEUP 0x00 ++#define RH_ENDPOINT_STALL 0x01 ++ ++/* Our Vendor Specific feature */ ++#define RH_REMOVE_EP 0x00 ++ ++ ++#define RH_ACK 0x01 ++#define RH_REQ_ERR -1 ++#define RH_NACK 0x00 ++ ++/* Field definitions for */ ++ ++#define USB_IN_command__eol__BITNR 0 /* command macros */ ++#define USB_IN_command__eol__WIDTH 1 ++#define USB_IN_command__eol__no 0 ++#define USB_IN_command__eol__yes 1 ++ ++#define USB_IN_command__intr__BITNR 3 ++#define USB_IN_command__intr__WIDTH 1 ++#define USB_IN_command__intr__no 0 ++#define USB_IN_command__intr__yes 1 ++ ++#define USB_IN_status__eop__BITNR 1 /* status macros. */ ++#define USB_IN_status__eop__WIDTH 1 ++#define USB_IN_status__eop__no 0 ++#define USB_IN_status__eop__yes 1 ++ ++#define USB_IN_status__eot__BITNR 5 ++#define USB_IN_status__eot__WIDTH 1 ++#define USB_IN_status__eot__no 0 ++#define USB_IN_status__eot__yes 1 ++ ++#define USB_IN_status__error__BITNR 6 ++#define USB_IN_status__error__WIDTH 1 ++#define USB_IN_status__error__no 0 ++#define USB_IN_status__error__yes 1 ++ ++#define USB_IN_status__nodata__BITNR 7 ++#define USB_IN_status__nodata__WIDTH 1 ++#define USB_IN_status__nodata__no 0 ++#define USB_IN_status__nodata__yes 1 ++ ++#define USB_IN_status__epid__BITNR 8 ++#define USB_IN_status__epid__WIDTH 5 ++ ++#define USB_EP_command__eol__BITNR 0 ++#define USB_EP_command__eol__WIDTH 1 ++#define USB_EP_command__eol__no 0 ++#define USB_EP_command__eol__yes 1 ++ ++#define USB_EP_command__eof__BITNR 1 ++#define USB_EP_command__eof__WIDTH 1 ++#define USB_EP_command__eof__no 0 ++#define USB_EP_command__eof__yes 1 ++ ++#define USB_EP_command__intr__BITNR 3 ++#define USB_EP_command__intr__WIDTH 1 ++#define USB_EP_command__intr__no 0 ++#define USB_EP_command__intr__yes 1 ++ ++#define USB_EP_command__enable__BITNR 4 ++#define USB_EP_command__enable__WIDTH 1 ++#define USB_EP_command__enable__no 0 ++#define USB_EP_command__enable__yes 1 ++ ++#define USB_EP_command__hw_valid__BITNR 5 ++#define USB_EP_command__hw_valid__WIDTH 1 ++#define USB_EP_command__hw_valid__no 0 ++#define USB_EP_command__hw_valid__yes 1 ++ ++#define USB_EP_command__epid__BITNR 8 ++#define USB_EP_command__epid__WIDTH 5 ++ ++#define USB_SB_command__eol__BITNR 0 /* command macros. */ ++#define USB_SB_command__eol__WIDTH 1 ++#define USB_SB_command__eol__no 0 ++#define USB_SB_command__eol__yes 1 ++ ++#define USB_SB_command__eot__BITNR 1 ++#define USB_SB_command__eot__WIDTH 1 ++#define USB_SB_command__eot__no 0 ++#define USB_SB_command__eot__yes 1 ++ ++#define USB_SB_command__intr__BITNR 3 ++#define USB_SB_command__intr__WIDTH 1 ++#define USB_SB_command__intr__no 0 ++#define USB_SB_command__intr__yes 1 ++ ++#define USB_SB_command__tt__BITNR 4 ++#define USB_SB_command__tt__WIDTH 2 ++#define USB_SB_command__tt__zout 0 ++#define USB_SB_command__tt__in 1 ++#define USB_SB_command__tt__out 2 ++#define USB_SB_command__tt__setup 3 ++ ++ ++#define USB_SB_command__rem__BITNR 8 ++#define USB_SB_command__rem__WIDTH 6 ++ ++#define USB_SB_command__full__BITNR 6 ++#define USB_SB_command__full__WIDTH 1 ++#define USB_SB_command__full__no 0 ++#define USB_SB_command__full__yes 1 ++ ++#endif +diff -urN linux-2.6.19.2.orig/drivers/net/cris/Makefile linux-2.6.19.2.dev/drivers/net/cris/Makefile +--- linux-2.6.19.2.orig/drivers/net/cris/Makefile 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/net/cris/Makefile 2005-01-04 13:09:12.000000000 +0100 +@@ -1 +1,2 @@ + obj-$(CONFIG_ETRAX_ARCH_V10) += eth_v10.o ++obj-$(CONFIG_ETRAX_ARCH_V32) += eth_v32.o +diff -urN linux-2.6.19.2.orig/drivers/net/cris/eth_v10.c linux-2.6.19.2.dev/drivers/net/cris/eth_v10.c +--- linux-2.6.19.2.orig/drivers/net/cris/eth_v10.c 2007-01-10 20:10:37.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/net/cris/eth_v10.c 2007-01-15 16:35:48.000000000 +0100 +@@ -1,221 +1,10 @@ +-/* $Id: ethernet.c,v 1.31 2004/10/18 14:49:03 starvik Exp $ +- * +- * e100net.c: A network driver for the ETRAX 100LX network controller. ++/* ++ * Driver for the ETRAX 100LX network controller. + * +- * Copyright (c) 1998-2002 Axis Communications AB. ++ * Copyright (c) 1998-2006 Axis Communications AB. + * + * The outline of this driver comes from skeleton.c. + * +- * $Log: ethernet.c,v $ +- * Revision 1.31 2004/10/18 14:49:03 starvik +- * Use RX interrupt as random source +- * +- * Revision 1.30 2004/09/29 10:44:04 starvik +- * Enabed MAC-address output again +- * +- * Revision 1.29 2004/08/24 07:14:05 starvik +- * Make use of generic MDIO interface and constants. +- * +- * Revision 1.28 2004/08/20 09:37:11 starvik +- * Added support for Intel LXT972A. Creds to Randy Scarborough. +- * +- * Revision 1.27 2004/08/16 12:37:22 starvik +- * Merge of Linux 2.6.8 +- * +- * Revision 1.25 2004/06/21 10:29:57 starvik +- * Merge of Linux 2.6.7 +- * +- * Revision 1.23 2004/06/09 05:29:22 starvik +- * Avoid any race where R_DMA_CH1_FIRST is NULL (may trigger cache bug). +- * +- * Revision 1.22 2004/05/14 07:58:03 starvik +- * Merge of changes from 2.4 +- * +- * Revision 1.20 2004/03/11 11:38:40 starvik +- * Merge of Linux 2.6.4 +- * +- * Revision 1.18 2003/12/03 13:45:46 starvik +- * Use hardware pad for short packets to prevent information leakage. +- * +- * Revision 1.17 2003/07/04 08:27:37 starvik +- * Merge of Linux 2.5.74 +- * +- * Revision 1.16 2003/04/24 08:28:22 starvik +- * New LED behaviour: LED off when no link +- * +- * Revision 1.15 2003/04/09 05:20:47 starvik +- * Merge of Linux 2.5.67 +- * +- * Revision 1.13 2003/03/06 16:11:01 henriken +- * Off by one error in group address register setting. +- * +- * Revision 1.12 2003/02/27 17:24:19 starvik +- * Corrected Rev to Revision +- * +- * Revision 1.11 2003/01/24 09:53:21 starvik +- * Oops. Initialize GA to 0, not to 1 +- * +- * Revision 1.10 2003/01/24 09:50:55 starvik +- * Initialize GA_0 and GA_1 to 0 to avoid matching of unwanted packets +- * +- * Revision 1.9 2002/12/13 07:40:58 starvik +- * Added basic ethtool interface +- * Handled out of memory when allocating new buffers +- * +- * Revision 1.8 2002/12/11 13:13:57 starvik +- * Added arch/ to v10 specific includes +- * Added fix from Linux 2.4 in serial.c (flush_to_flip_buffer) +- * +- * Revision 1.7 2002/11/26 09:41:42 starvik +- * Added e100_set_config (standard interface to set media type) +- * Added protection against preemptive scheduling +- * Added standard MII ioctls +- * +- * Revision 1.6 2002/11/21 07:18:18 starvik +- * Timers must be initialized in 2.5.48 +- * +- * Revision 1.5 2002/11/20 11:56:11 starvik +- * Merge of Linux 2.5.48 +- * +- * Revision 1.4 2002/11/18 07:26:46 starvik +- * Linux 2.5 port of latest Linux 2.4 ethernet driver +- * +- * Revision 1.33 2002/10/02 20:16:17 hp +- * SETF, SETS: Use underscored IO_x_ macros rather than incorrect token concatenation +- * +- * Revision 1.32 2002/09/16 06:05:58 starvik +- * Align memory returned by dev_alloc_skb +- * Moved handling of sent packets to interrupt to avoid reference counting problem +- * +- * Revision 1.31 2002/09/10 13:28:23 larsv +- * Return -EINVAL for unknown ioctls to avoid confusing tools that tests +- * for supported functionality by issuing special ioctls, i.e. wireless +- * extensions. +- * +- * Revision 1.30 2002/05/07 18:50:08 johana +- * Correct spelling in comments. +- * +- * Revision 1.29 2002/05/06 05:38:49 starvik +- * Performance improvements: +- * Large packets are not copied (breakpoint set to 256 bytes) +- * The cache bug workaround is delayed until half of the receive list +- * has been used +- * Added transmit list +- * Transmit interrupts are only enabled when transmit queue is full +- * +- * Revision 1.28.2.1 2002/04/30 08:15:51 starvik +- * Performance improvements: +- * Large packets are not copied (breakpoint set to 256 bytes) +- * The cache bug workaround is delayed until half of the receive list +- * has been used. +- * Added transmit list +- * Transmit interrupts are only enabled when transmit queue is full +- * +- * Revision 1.28 2002/04/22 11:47:21 johana +- * Fix according to 2.4.19-pre7. time_after/time_before and +- * missing end of comment. +- * The patch has a typo for ethernet.c in e100_clear_network_leds(), +- * that is fixed here. +- * +- * Revision 1.27 2002/04/12 11:55:11 bjornw +- * Added TODO +- * +- * Revision 1.26 2002/03/15 17:11:02 bjornw +- * Use prepare_rx_descriptor after the CPU has touched the receiving descs +- * +- * Revision 1.25 2002/03/08 13:07:53 bjornw +- * Unnecessary spinlock removed +- * +- * Revision 1.24 2002/02/20 12:57:43 fredriks +- * Replaced MIN() with min(). +- * +- * Revision 1.23 2002/02/20 10:58:14 fredriks +- * Strip the Ethernet checksum (4 bytes) before forwarding a frame to upper layers. +- * +- * Revision 1.22 2002/01/30 07:48:22 matsfg +- * Initiate R_NETWORK_TR_CTRL +- * +- * Revision 1.21 2001/11/23 11:54:49 starvik +- * Added IFF_PROMISC and IFF_ALLMULTI handling in set_multicast_list +- * Removed compiler warnings +- * +- * Revision 1.20 2001/11/12 19:26:00 pkj +- * * Corrected e100_negotiate() to not assign half to current_duplex when +- * it was supposed to compare them... +- * * Cleaned up failure handling in e100_open(). +- * * Fixed compiler warnings. +- * +- * Revision 1.19 2001/11/09 07:43:09 starvik +- * Added full duplex support +- * Added ioctl to set speed and duplex +- * Clear LED timer only runs when LED is lit +- * +- * Revision 1.18 2001/10/03 14:40:43 jonashg +- * Update rx_bytes counter. +- * +- * Revision 1.17 2001/06/11 12:43:46 olof +- * Modified defines for network LED behavior +- * +- * Revision 1.16 2001/05/30 06:12:46 markusl +- * TxDesc.next should not be set to NULL +- * +- * Revision 1.15 2001/05/29 10:27:04 markusl +- * Updated after review remarks: +- * +Use IO_EXTRACT +- * +Handle underrun +- * +- * Revision 1.14 2001/05/29 09:20:14 jonashg +- * Use driver name on printk output so one can tell which driver that complains. +- * +- * Revision 1.13 2001/05/09 12:35:59 johana +- * Use DMA_NBR and IRQ_NBR defines from dma.h and irq.h +- * +- * Revision 1.12 2001/04/05 11:43:11 tobiasa +- * Check dev before panic. +- * +- * Revision 1.11 2001/04/04 11:21:05 markusl +- * Updated according to review remarks +- * +- * Revision 1.10 2001/03/26 16:03:06 bjornw +- * Needs linux/config.h +- * +- * Revision 1.9 2001/03/19 14:47:48 pkj +- * * Make sure there is always a pause after the network LEDs are +- * changed so they will not look constantly lit during heavy traffic. +- * * Always use HZ when setting times relative to jiffies. +- * * Use LED_NETWORK_SET() when setting the network LEDs. +- * +- * Revision 1.8 2001/02/27 13:52:48 bjornw +- * malloc.h -> slab.h +- * +- * Revision 1.7 2001/02/23 13:46:38 bjornw +- * Spellling check +- * +- * Revision 1.6 2001/01/26 15:21:04 starvik +- * Don't disable interrupts while reading MDIO registers (MDIO is slow) +- * Corrected promiscuous mode +- * Improved deallocation of IRQs ("ifconfig eth0 down" now works) +- * +- * Revision 1.5 2000/11/29 17:22:22 bjornw +- * Get rid of the udword types legacy stuff +- * +- * Revision 1.4 2000/11/22 16:36:09 bjornw +- * Please marketing by using the correct case when spelling Etrax. +- * +- * Revision 1.3 2000/11/21 16:43:04 bjornw +- * Minor short->int change +- * +- * Revision 1.2 2000/11/08 14:27:57 bjornw +- * 2.4 port +- * +- * Revision 1.1 2000/11/06 13:56:00 bjornw +- * Verbatim copy of the 1.24 version of e100net.c from elinux +- * +- * Revision 1.24 2000/10/04 15:55:23 bjornw +- * * Use virt_to_phys etc. for DMA addresses +- * * Removed bogus CHECKSUM_UNNECESSARY +- * +- * + */ + + +@@ -251,6 +40,7 @@ + #include <asm/bitops.h> + #include <asm/ethernet.h> + #include <asm/cache.h> ++#include <asm/arch/io_interface_mux.h> + + //#define ETHDEBUG + #define D(x) +@@ -280,6 +70,9 @@ + * by this lock as well. + */ + spinlock_t lock; ++ ++ spinlock_t led_lock; /* Protect LED state */ ++ spinlock_t transceiver_lock; /* Protect transceiver state. */ + }; + + typedef struct etrax_eth_descr +@@ -296,8 +89,6 @@ + void (*check_duplex)(struct net_device* dev); + }; + +-struct transceiver_ops* transceiver; +- + /* Duplex settings */ + enum duplex + { +@@ -308,7 +99,7 @@ + + /* Dma descriptors etc. */ + +-#define MAX_MEDIA_DATA_SIZE 1518 ++#define MAX_MEDIA_DATA_SIZE 1522 + + #define MIN_PACKET_LEN 46 + #define ETHER_HEAD_LEN 14 +@@ -332,9 +123,9 @@ + #define MDIO_TDK_DIAGNOSTIC_DPLX 0x800 + + /*Intel LXT972A specific*/ +-#define MDIO_INT_STATUS_REG_2 0x0011 +-#define MDIO_INT_FULL_DUPLEX_IND ( 1 << 9 ) +-#define MDIO_INT_SPEED ( 1 << 14 ) ++#define MDIO_INT_STATUS_REG_2 0x0011 ++#define MDIO_INT_FULL_DUPLEX_IND (1 << 9) ++#define MDIO_INT_SPEED (1 << 14) + + /* Network flash constants */ + #define NET_FLASH_TIME (HZ/50) /* 20 ms */ +@@ -345,8 +136,8 @@ + #define NO_NETWORK_ACTIVITY 0 + #define NETWORK_ACTIVITY 1 + +-#define NBR_OF_RX_DESC 64 +-#define NBR_OF_TX_DESC 256 ++#define NBR_OF_RX_DESC 32 ++#define NBR_OF_TX_DESC 16 + + /* Large packets are sent directly to upper layers while small packets are */ + /* copied (to reduce memory waste). The following constant decides the breakpoint */ +@@ -368,7 +159,6 @@ + static etrax_eth_descr *myNextRxDesc; /* Points to the next descriptor to + to be processed */ + static etrax_eth_descr *myLastRxDesc; /* The last processed descriptor */ +-static etrax_eth_descr *myPrevRxDesc; /* The descriptor right before myNextRxDesc */ + + static etrax_eth_descr RxDescList[NBR_OF_RX_DESC] __attribute__ ((aligned(32))); + +@@ -378,7 +168,6 @@ + static etrax_eth_descr TxDescList[NBR_OF_TX_DESC] __attribute__ ((aligned(32))); + + static unsigned int network_rec_config_shadow = 0; +-static unsigned int mdio_phy_addr; /* Transciever address */ + + static unsigned int network_tr_ctrl_shadow = 0; + +@@ -412,7 +201,7 @@ + static void e100_tx_timeout(struct net_device *dev); + static struct net_device_stats *e100_get_stats(struct net_device *dev); + static void set_multicast_list(struct net_device *dev); +-static void e100_hardware_send_packet(char *buf, int length); ++static void e100_hardware_send_packet(struct net_local* np, char *buf, int length); + static void update_rx_stats(struct net_device_stats *); + static void update_tx_stats(struct net_device_stats *); + static int e100_probe_transceiver(struct net_device* dev); +@@ -435,7 +224,10 @@ + static void e100_set_network_leds(int active); + + static const struct ethtool_ops e100_ethtool_ops; +- ++#if defined(CONFIG_ETRAX_NO_PHY) ++static void dummy_check_speed(struct net_device* dev); ++static void dummy_check_duplex(struct net_device* dev); ++#else + static void broadcom_check_speed(struct net_device* dev); + static void broadcom_check_duplex(struct net_device* dev); + static void tdk_check_speed(struct net_device* dev); +@@ -444,16 +236,29 @@ + static void intel_check_duplex(struct net_device* dev); + static void generic_check_speed(struct net_device* dev); + static void generic_check_duplex(struct net_device* dev); ++#endif ++#ifdef CONFIG_NET_POLL_CONTROLLER ++static void e100_netpoll(struct net_device* dev); ++#endif ++ ++static int autoneg_normal = 1; + + struct transceiver_ops transceivers[] = + { ++#if defined(CONFIG_ETRAX_NO_PHY) ++ {0x0000, dummy_check_speed, dummy_check_duplex} /* Dummy */ ++#else + {0x1018, broadcom_check_speed, broadcom_check_duplex}, /* Broadcom */ + {0xC039, tdk_check_speed, tdk_check_duplex}, /* TDK 2120 */ + {0x039C, tdk_check_speed, tdk_check_duplex}, /* TDK 2120C */ +- {0x04de, intel_check_speed, intel_check_duplex}, /* Intel LXT972A*/ ++ {0x04de, intel_check_speed, intel_check_duplex}, /* Intel LXT972A*/ + {0x0000, generic_check_speed, generic_check_duplex} /* Generic, must be last */ ++#endif + }; + ++struct transceiver_ops* transceiver = &transceivers[0]; ++static unsigned int mdio_phy_addr = 0; /* PHY address on MDIO bus */ ++ + #define tx_done(dev) (*R_DMA_CH0_CMD == 0) + + /* +@@ -468,18 +273,26 @@ + etrax_ethernet_init(void) + { + struct net_device *dev; +- struct net_local* np; ++ struct net_local* np; + int i, err; + + printk(KERN_INFO +- "ETRAX 100LX 10/100MBit ethernet v2.0 (c) 2000-2003 Axis Communications AB\n"); +- ++ "ETRAX 100LX 10/100MBit ethernet v2.0 (c) 1998-2006 Axis Communications AB\n"); ++ ++ if (cris_request_io_interface(if_eth, cardname)) { ++ printk(KERN_CRIT "etrax_ethernet_init failed to get IO interface\n"); ++ return -EBUSY; ++ } ++ + dev = alloc_etherdev(sizeof(struct net_local)); +- np = dev->priv; +- + if (!dev) + return -ENOMEM; ++ ++ np = netdev_priv(dev); + ++ /* we do our own locking */ ++ dev->features |= NETIF_F_LLTX; ++ + dev->base_addr = (unsigned int)R_NETWORK_SA_0; /* just to have something to show */ + + /* now setup our etrax specific stuff */ +@@ -495,18 +308,26 @@ + dev->get_stats = e100_get_stats; + dev->set_multicast_list = set_multicast_list; + dev->set_mac_address = e100_set_mac_address; +- dev->ethtool_ops = &e100_ethtool_ops; ++ dev->ethtool_ops = &e100_ethtool_ops; + dev->do_ioctl = e100_ioctl; +- dev->set_config = e100_set_config; ++ dev->set_config = e100_set_config; + dev->tx_timeout = e100_tx_timeout; ++#ifdef CONFIG_NET_POLL_CONTROLLER ++ dev->poll_controller = e100_netpoll; ++#endif ++ ++ spin_lock_init(&np->lock); ++ spin_lock_init(&np->led_lock); ++ spin_lock_init(&np->transceiver_lock); + + /* Initialise the list of Etrax DMA-descriptors */ + + /* Initialise receive descriptors */ + + for (i = 0; i < NBR_OF_RX_DESC; i++) { +- /* Allocate two extra cachelines to make sure that buffer used by DMA +- * does not share cacheline with any other data (to avoid cache bug) ++ /* Allocate two extra cachelines to make sure that buffer used ++ * by DMA does not share cacheline with any other data (to ++ * avoid cache bug) + */ + RxDescList[i].skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE + 2 * L1_CACHE_BYTES); + if (!RxDescList[i].skb) +@@ -517,6 +338,7 @@ + RxDescList[i].descr.buf = L1_CACHE_ALIGN(virt_to_phys(RxDescList[i].skb->data)); + RxDescList[i].descr.status = 0; + RxDescList[i].descr.hw_len = 0; ++ + prepare_rx_descriptor(&RxDescList[i].descr); + } + +@@ -542,7 +364,6 @@ + + myNextRxDesc = &RxDescList[0]; + myLastRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; +- myPrevRxDesc = &RxDescList[NBR_OF_RX_DESC - 1]; + myFirstTxDesc = &TxDescList[0]; + myNextTxDesc = &TxDescList[0]; + myLastTxDesc = &TxDescList[NBR_OF_TX_DESC - 1]; +@@ -563,18 +384,19 @@ + current_speed = 10; + current_speed_selection = 0; /* Auto */ + speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL; +- duplex_timer.data = (unsigned long)dev; ++ speed_timer.data = (unsigned long)dev; + speed_timer.function = e100_check_speed; + + clear_led_timer.function = e100_clear_network_leds; ++ clear_led_timer.data = (unsigned long)dev; + + full_duplex = 0; + current_duplex = autoneg; + duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL; +- duplex_timer.data = (unsigned long)dev; ++ duplex_timer.data = (unsigned long)dev; + duplex_timer.function = e100_check_duplex; + +- /* Initialize mii interface */ ++ /* Initialize mii interface */ + np->mii_if.phy_id = mdio_phy_addr; + np->mii_if.phy_id_mask = 0x1f; + np->mii_if.reg_num_mask = 0x1f; +@@ -586,6 +408,9 @@ + /* unwanted addresses are matched */ + *R_NETWORK_GA_0 = 0x00000000; + *R_NETWORK_GA_1 = 0x00000000; ++ ++ /* Initialize next time the led can flash */ ++ led_next_time = jiffies; + return 0; + } + +@@ -596,7 +421,7 @@ + static int + e100_set_mac_address(struct net_device *dev, void *p) + { +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + struct sockaddr *addr = p; + int i; + +@@ -680,17 +505,36 @@ + /* allocate the irq corresponding to the transmitting DMA */ + + if (request_irq(NETWORK_DMA_TX_IRQ_NBR, e100rxtx_interrupt, 0, +- cardname, (void *)dev)) { ++ cardname, (void *)dev)) { + goto grace_exit1; + } + + /* allocate the irq corresponding to the network errors etc */ + + if (request_irq(NETWORK_STATUS_IRQ_NBR, e100nw_interrupt, 0, +- cardname, (void *)dev)) { ++ cardname, (void *)dev)) { + goto grace_exit2; + } + ++ /* ++ * Always allocate the DMA channels after the IRQ, ++ * and clean up on failure. ++ */ ++ ++ if (cris_request_dma(NETWORK_TX_DMA_NBR, ++ cardname, ++ DMA_VERBOSE_ON_ERROR, ++ dma_eth)) { ++ goto grace_exit3; ++ } ++ ++ if (cris_request_dma(NETWORK_RX_DMA_NBR, ++ cardname, ++ DMA_VERBOSE_ON_ERROR, ++ dma_eth)) { ++ goto grace_exit4; ++ } ++ + /* give the HW an idea of what MAC address we want */ + + *R_NETWORK_SA_0 = dev->dev_addr[0] | (dev->dev_addr[1] << 8) | +@@ -705,6 +549,7 @@ + + *R_NETWORK_REC_CONFIG = 0xd; /* broadcast rec, individ. rec, ma0 enabled */ + #else ++ SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, max_size, size1522); + SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, broadcast, receive); + SETS(network_rec_config_shadow, R_NETWORK_REC_CONFIG, ma0, enable); + SETF(network_rec_config_shadow, R_NETWORK_REC_CONFIG, duplex, full_duplex); +@@ -724,8 +569,7 @@ + SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, crc, enable); + *R_NETWORK_TR_CTRL = network_tr_ctrl_shadow; + +- save_flags(flags); +- cli(); ++ local_irq_save(flags); + + /* enable the irq's for ethernet DMA */ + +@@ -757,12 +601,13 @@ + + *R_DMA_CH0_FIRST = 0; + *R_DMA_CH0_DESCR = virt_to_phys(myLastTxDesc); ++ netif_start_queue(dev); + +- restore_flags(flags); ++ local_irq_restore(flags); + + /* Probe for transceiver */ + if (e100_probe_transceiver(dev)) +- goto grace_exit3; ++ goto grace_exit5; + + /* Start duplex/speed timers */ + add_timer(&speed_timer); +@@ -771,10 +616,14 @@ + /* We are now ready to accept transmit requeusts from + * the queueing layer of the networking. + */ +- netif_start_queue(dev); ++ netif_carrier_on(dev); + + return 0; + ++grace_exit5: ++ cris_free_dma(NETWORK_RX_DMA_NBR, cardname); ++grace_exit4: ++ cris_free_dma(NETWORK_TX_DMA_NBR, cardname); + grace_exit3: + free_irq(NETWORK_STATUS_IRQ_NBR, (void *)dev); + grace_exit2: +@@ -785,7 +634,13 @@ + return -EAGAIN; + } + +- ++#if defined(CONFIG_ETRAX_NO_PHY) ++static void ++dummy_check_speed(struct net_device* dev) ++{ ++ current_speed = 100; ++} ++#else + static void + generic_check_speed(struct net_device* dev) + { +@@ -821,15 +676,18 @@ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_INT_STATUS_REG_2); + current_speed = (data & MDIO_INT_SPEED ? 100 : 10); + } +- ++#endif + static void + e100_check_speed(unsigned long priv) + { + struct net_device* dev = (struct net_device*)priv; ++ struct net_local *np = netdev_priv(dev); + static int led_initiated = 0; + unsigned long data; + int old_speed = current_speed; + ++ spin_lock(&np->transceiver_lock); ++ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMSR); + if (!(data & BMSR_LSTATUS)) { + current_speed = 0; +@@ -837,14 +695,22 @@ + transceiver->check_speed(dev); + } + ++ spin_lock(&np->led_lock); + if ((old_speed != current_speed) || !led_initiated) { + led_initiated = 1; + e100_set_network_leds(NO_NETWORK_ACTIVITY); ++ if (current_speed) ++ netif_carrier_on(dev); ++ else ++ netif_carrier_off(dev); + } ++ spin_unlock(&np->led_lock); + + /* Reinitialize the timer. */ + speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL; + add_timer(&speed_timer); ++ ++ spin_unlock(&np->transceiver_lock); + } + + static void +@@ -857,7 +723,7 @@ + ADVERTISE_10HALF | ADVERTISE_10FULL); + + switch (current_speed_selection) { +- case 10 : ++ case 10: + if (current_duplex == full) + data |= ADVERTISE_10FULL; + else if (current_duplex == half) +@@ -866,7 +732,7 @@ + data |= ADVERTISE_10HALF | ADVERTISE_10FULL; + break; + +- case 100 : ++ case 100: + if (current_duplex == full) + data |= ADVERTISE_100FULL; + else if (current_duplex == half) +@@ -875,45 +741,54 @@ + data |= ADVERTISE_100HALF | ADVERTISE_100FULL; + break; + +- case 0 : /* Auto */ ++ case 0: /* Auto */ + if (current_duplex == full) + data |= ADVERTISE_100FULL | ADVERTISE_10FULL; + else if (current_duplex == half) + data |= ADVERTISE_100HALF | ADVERTISE_10HALF; + else + data |= ADVERTISE_10HALF | ADVERTISE_10FULL | +- ADVERTISE_100HALF | ADVERTISE_100FULL; ++ ADVERTISE_100HALF | ADVERTISE_100FULL; + break; + +- default : /* assume autoneg speed and duplex */ ++ default: /* assume autoneg speed and duplex */ + data |= ADVERTISE_10HALF | ADVERTISE_10FULL | +- ADVERTISE_100HALF | ADVERTISE_100FULL; ++ ADVERTISE_100HALF | ADVERTISE_100FULL; ++ break; + } + + e100_set_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE, data); + + /* Renegotiate with link partner */ +- data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMCR); +- data |= BMCR_ANENABLE | BMCR_ANRESTART; +- ++ if (autoneg_normal) { ++ data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_BMCR); ++ data |= BMCR_ANENABLE | BMCR_ANRESTART; ++ } + e100_set_mdio_reg(dev, mdio_phy_addr, MII_BMCR, data); + } + + static void + e100_set_speed(struct net_device* dev, unsigned long speed) + { ++ struct net_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->transceiver_lock); + if (speed != current_speed_selection) { + current_speed_selection = speed; + e100_negotiate(dev); + } ++ spin_unlock(&np->transceiver_lock); + } + + static void + e100_check_duplex(unsigned long priv) + { + struct net_device *dev = (struct net_device *)priv; +- struct net_local *np = (struct net_local *)dev->priv; +- int old_duplex = full_duplex; ++ struct net_local *np = netdev_priv(dev); ++ int old_duplex; ++ ++ spin_lock(&np->transceiver_lock); ++ old_duplex = full_duplex; + transceiver->check_duplex(dev); + if (old_duplex != full_duplex) { + /* Duplex changed */ +@@ -925,12 +800,20 @@ + duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL; + add_timer(&duplex_timer); + np->mii_if.full_duplex = full_duplex; ++ spin_unlock(&np->transceiver_lock); + } +- ++#if defined(CONFIG_ETRAX_NO_PHY) ++static void ++dummy_check_duplex(struct net_device* dev) ++{ ++ full_duplex = 1; ++} ++#else + static void + generic_check_duplex(struct net_device* dev) + { + unsigned long data; ++ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MII_ADVERTISE); + if ((data & ADVERTISE_10FULL) || + (data & ADVERTISE_100FULL)) +@@ -943,6 +826,7 @@ + tdk_check_duplex(struct net_device* dev) + { + unsigned long data; ++ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_TDK_DIAGNOSTIC_REG); + full_duplex = (data & MDIO_TDK_DIAGNOSTIC_DPLX) ? 1 : 0; + } +@@ -951,6 +835,7 @@ + broadcom_check_duplex(struct net_device* dev) + { + unsigned long data; ++ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_AUX_CTRL_STATUS_REG); + full_duplex = (data & MDIO_BC_FULL_DUPLEX_IND) ? 1 : 0; + } +@@ -959,26 +844,35 @@ + intel_check_duplex(struct net_device* dev) + { + unsigned long data; ++ + data = e100_get_mdio_reg(dev, mdio_phy_addr, MDIO_INT_STATUS_REG_2); + full_duplex = (data & MDIO_INT_FULL_DUPLEX_IND) ? 1 : 0; + } +- ++#endif + static void + e100_set_duplex(struct net_device* dev, enum duplex new_duplex) + { ++ struct net_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->transceiver_lock); + if (new_duplex != current_duplex) { + current_duplex = new_duplex; + e100_negotiate(dev); + } ++ spin_unlock(&np->transceiver_lock); + } + + static int + e100_probe_transceiver(struct net_device* dev) + { ++#if !defined(CONFIG_ETRAX_NO_PHY) + unsigned int phyid_high; + unsigned int phyid_low; + unsigned int oui; + struct transceiver_ops* ops = NULL; ++ struct net_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->transceiver_lock); + + /* Probe MDIO physical address */ + for (mdio_phy_addr = 0; mdio_phy_addr <= 31; mdio_phy_addr++) { +@@ -986,7 +880,7 @@ + break; + } + if (mdio_phy_addr == 32) +- return -ENODEV; ++ return -ENODEV; + + /* Get manufacturer */ + phyid_high = e100_get_mdio_reg(dev, mdio_phy_addr, MII_PHYSID1); +@@ -999,6 +893,8 @@ + } + transceiver = ops; + ++ spin_unlock(&np->transceiver_lock); ++#endif + return 0; + } + +@@ -1006,7 +902,7 @@ + e100_get_mdio_reg(struct net_device *dev, int phy_id, int location) + { + unsigned short cmd; /* Data to be sent on MDIO port */ +- int data; /* Data read from MDIO */ ++ int data; /* Data read from MDIO */ + int bitCounter; + + /* Start of frame, OP Code, Physical Address, Register Address */ +@@ -1082,6 +978,7 @@ + e100_receive_mdio_bit() + { + unsigned char bit; ++ + *R_NETWORK_MGM_CTRL = 0; + bit = IO_EXTRACT(R_NETWORK_STAT, mdio, *R_NETWORK_STAT); + udelay(1); +@@ -1117,7 +1014,7 @@ + static void + e100_tx_timeout(struct net_device *dev) + { +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + unsigned long flags; + + spin_lock_irqsave(&np->lock, flags); +@@ -1139,8 +1036,7 @@ + e100_reset_transceiver(dev); + + /* and get rid of the packets that never got an interrupt */ +- while (myFirstTxDesc != myNextTxDesc) +- { ++ while (myFirstTxDesc != myNextTxDesc) { + dev_kfree_skb(myFirstTxDesc->skb); + myFirstTxDesc->skb = 0; + myFirstTxDesc = phys_to_virt(myFirstTxDesc->descr.next); +@@ -1166,7 +1062,7 @@ + static int + e100_send_packet(struct sk_buff *skb, struct net_device *dev) + { +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + unsigned char *buf = skb->data; + unsigned long flags; + +@@ -1179,7 +1075,7 @@ + + dev->trans_start = jiffies; + +- e100_hardware_send_packet(buf, skb->len); ++ e100_hardware_send_packet(np, buf, skb->len); + + myNextTxDesc = phys_to_virt(myNextTxDesc->descr.next); + +@@ -1202,13 +1098,15 @@ + e100rxtx_interrupt(int irq, void *dev_id) + { + struct net_device *dev = (struct net_device *)dev_id; +- struct net_local *np = (struct net_local *)dev->priv; +- unsigned long irqbits = *R_IRQ_MASK2_RD; ++ struct net_local *np = netdev_priv(dev); ++ unsigned long irqbits; + +- /* Disable RX/TX IRQs to avoid reentrancy */ +- *R_IRQ_MASK2_CLR = +- IO_STATE(R_IRQ_MASK2_CLR, dma0_eop, clr) | +- IO_STATE(R_IRQ_MASK2_CLR, dma1_eop, clr); ++ /* ++ * Note that both rx and tx interrupts are blocked at this point, ++ * regardless of which got us here. ++ */ ++ ++ irqbits = *R_IRQ_MASK2_RD; + + /* Handle received packets */ + if (irqbits & IO_STATE(R_IRQ_MASK2_RD, dma1_eop, active)) { +@@ -1224,7 +1122,7 @@ + * allocate a new buffer to put a packet in. + */ + e100_rx(dev); +- ((struct net_local *)dev->priv)->stats.rx_packets++; ++ np->stats.rx_packets++; + /* restart/continue on the channel, for safety */ + *R_DMA_CH1_CMD = IO_STATE(R_DMA_CH1_CMD, cmd, restart); + /* clear dma channel 1 eop/descr irq bits */ +@@ -1239,8 +1137,7 @@ + + /* Report any packets that have been sent */ + while (myFirstTxDesc != phys_to_virt(*R_DMA_CH0_FIRST) && +- myFirstTxDesc != myNextTxDesc) +- { ++ (netif_queue_stopped(dev) || myFirstTxDesc != myNextTxDesc)) { + np->stats.tx_bytes += myFirstTxDesc->skb->len; + np->stats.tx_packets++; + +@@ -1249,19 +1146,15 @@ + dev_kfree_skb_irq(myFirstTxDesc->skb); + myFirstTxDesc->skb = 0; + myFirstTxDesc = phys_to_virt(myFirstTxDesc->descr.next); ++ /* Wake up queue. */ ++ netif_wake_queue(dev); + } + + if (irqbits & IO_STATE(R_IRQ_MASK2_RD, dma0_eop, active)) { +- /* acknowledge the eop interrupt and wake up queue */ ++ /* acknowledge the eop interrupt. */ + *R_DMA_CH0_CLR_INTR = IO_STATE(R_DMA_CH0_CLR_INTR, clr_eop, do); +- netif_wake_queue(dev); + } + +- /* Enable RX/TX IRQs again */ +- *R_IRQ_MASK2_SET = +- IO_STATE(R_IRQ_MASK2_SET, dma0_eop, set) | +- IO_STATE(R_IRQ_MASK2_SET, dma1_eop, set); +- + return IRQ_HANDLED; + } + +@@ -1269,7 +1162,7 @@ + e100nw_interrupt(int irq, void *dev_id) + { + struct net_device *dev = (struct net_device *)dev_id; +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + unsigned long irqbits = *R_IRQ_MASK0_RD; + + /* check for underrun irq */ +@@ -1291,7 +1184,6 @@ + SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, clr_error, clr); + *R_NETWORK_TR_CTRL = network_tr_ctrl_shadow; + SETS(network_tr_ctrl_shadow, R_NETWORK_TR_CTRL, clr_error, nop); +- *R_NETWORK_TR_CTRL = IO_STATE(R_NETWORK_TR_CTRL, clr_error, clr); + np->stats.tx_errors++; + D(printk("ethernet excessive collisions!\n")); + } +@@ -1304,12 +1196,13 @@ + { + struct sk_buff *skb; + int length = 0; +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + unsigned char *skb_data_ptr; + #ifdef ETHDEBUG + int i; + #endif +- ++ etrax_eth_descr *prevRxDesc; /* The descriptor right before myNextRxDesc */ ++ spin_lock(&np->led_lock); + if (!led_active && time_after(jiffies, led_next_time)) { + /* light the network leds depending on the current speed. */ + e100_set_network_leds(NETWORK_ACTIVITY); +@@ -1319,9 +1212,10 @@ + led_active = 1; + mod_timer(&clear_led_timer, jiffies + HZ/10); + } ++ spin_unlock(&np->led_lock); + + length = myNextRxDesc->descr.hw_len - 4; +- ((struct net_local *)dev->priv)->stats.rx_bytes += length; ++ np->stats.rx_bytes += length; + + #ifdef ETHDEBUG + printk("Got a packet of length %d:\n", length); +@@ -1341,7 +1235,7 @@ + if (!skb) { + np->stats.rx_errors++; + printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name); +- return; ++ goto update_nextrxdesc; + } + + skb_put(skb, length - ETHER_HEAD_LEN); /* allocate room for the packet body */ +@@ -1358,15 +1252,15 @@ + else { + /* Large packet, send directly to upper layers and allocate new + * memory (aligned to cache line boundary to avoid bug). +- * Before sending the skb to upper layers we must make sure that +- * skb->data points to the aligned start of the packet. ++ * Before sending the skb to upper layers we must make sure ++ * that skb->data points to the aligned start of the packet. + */ + int align; + struct sk_buff *new_skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE + 2 * L1_CACHE_BYTES); + if (!new_skb) { + np->stats.rx_errors++; + printk(KERN_NOTICE "%s: Memory squeeze, dropping packet.\n", dev->name); +- return; ++ goto update_nextrxdesc; + } + skb = myNextRxDesc->skb; + align = (int)phys_to_virt(myNextRxDesc->descr.buf) - (int)skb->data; +@@ -1382,9 +1276,10 @@ + /* Send the packet to the upper layers */ + netif_rx(skb); + ++ update_nextrxdesc: + /* Prepare for next packet */ + myNextRxDesc->descr.status = 0; +- myPrevRxDesc = myNextRxDesc; ++ prevRxDesc = myNextRxDesc; + myNextRxDesc = phys_to_virt(myNextRxDesc->descr.next); + + rx_queue_len++; +@@ -1392,9 +1287,9 @@ + /* Check if descriptors should be returned */ + if (rx_queue_len == RX_QUEUE_THRESHOLD) { + flush_etrax_cache(); +- myPrevRxDesc->descr.ctrl |= d_eol; ++ prevRxDesc->descr.ctrl |= d_eol; + myLastRxDesc->descr.ctrl &= ~d_eol; +- myLastRxDesc = myPrevRxDesc; ++ myLastRxDesc = prevRxDesc; + rx_queue_len = 0; + } + } +@@ -1403,7 +1298,7 @@ + static int + e100_close(struct net_device *dev) + { +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); + + printk(KERN_INFO "Closing %s.\n", dev->name); + +@@ -1431,6 +1326,9 @@ + free_irq(NETWORK_DMA_TX_IRQ_NBR, (void *)dev); + free_irq(NETWORK_STATUS_IRQ_NBR, (void *)dev); + ++ cris_free_dma(NETWORK_TX_DMA_NBR, cardname); ++ cris_free_dma(NETWORK_RX_DMA_NBR, cardname); ++ + /* Update the statistics here. */ + + update_rx_stats(&np->stats); +@@ -1448,46 +1346,56 @@ + { + struct mii_ioctl_data *data = if_mii(ifr); + struct net_local *np = netdev_priv(dev); ++ int ret = 0; ++ int old_autoneg; + + spin_lock(&np->lock); /* Preempt protection */ + switch (cmd) { +- case SIOCGMIIPHY: /* Get PHY address */ ++ case SIOCGMIIPHY: /* Get PHY address */ + data->phy_id = mdio_phy_addr; + break; +- case SIOCGMIIREG: /* Read MII register */ ++ case SIOCGMIIREG: /* Read MII register */ + data->val_out = e100_get_mdio_reg(dev, mdio_phy_addr, data->reg_num); + break; +- case SIOCSMIIREG: /* Write MII register */ ++ case SIOCSMIIREG: /* Write MII register */ + e100_set_mdio_reg(dev, mdio_phy_addr, data->reg_num, data->val_in); + break; ++ + /* The ioctls below should be considered obsolete but are */ + /* still present for compatability with old scripts/apps */ +- case SET_ETH_SPEED_10: /* 10 Mbps */ ++ case SET_ETH_SPEED_10: /* 10 Mbps */ + e100_set_speed(dev, 10); + break; +- case SET_ETH_SPEED_100: /* 100 Mbps */ ++ case SET_ETH_SPEED_100: /* 100 Mbps */ + e100_set_speed(dev, 100); + break; +- case SET_ETH_SPEED_AUTO: /* Auto negotiate speed */ ++ case SET_ETH_SPEED_AUTO: /* Auto-negotiate speed */ + e100_set_speed(dev, 0); + break; +- case SET_ETH_DUPLEX_HALF: /* Half duplex. */ ++ case SET_ETH_DUPLEX_HALF: /* Half duplex */ + e100_set_duplex(dev, half); + break; +- case SET_ETH_DUPLEX_FULL: /* Full duplex. */ ++ case SET_ETH_DUPLEX_FULL: /* Full duplex */ + e100_set_duplex(dev, full); + break; +- case SET_ETH_DUPLEX_AUTO: /* Autonegotiate duplex*/ ++ case SET_ETH_DUPLEX_AUTO: /* Auto-negotiate duplex */ + e100_set_duplex(dev, autoneg); + break; ++ case SET_ETH_AUTONEG: ++ old_autoneg = autoneg_normal; ++ autoneg_normal = *(int*)data; ++ if (autoneg_normal != old_autoneg) ++ e100_negotiate(dev); ++ break; + default: ++ spin_unlock(&np->lock); + return -EINVAL; + } + spin_unlock(&np->lock); +- return 0; ++ return ret; + } + +-static int e100_set_settings(struct net_device *dev, ++static int e100_get_settings(struct net_device *dev, + struct ethtool_cmd *ecmd) + { + ecmd->supported = SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII | +@@ -1565,7 +1473,8 @@ + static int + e100_set_config(struct net_device *dev, struct ifmap *map) + { +- struct net_local *np = (struct net_local *)dev->priv; ++ struct net_local *np = netdev_priv(dev); ++ + spin_lock(&np->lock); /* Preempt protection */ + + switch(map->port) { +@@ -1574,21 +1483,25 @@ + e100_set_speed(dev, 0); + e100_set_duplex(dev, autoneg); + break; ++ + case IF_PORT_10BASET: + e100_set_speed(dev, 10); + e100_set_duplex(dev, autoneg); + break; ++ + case IF_PORT_100BASET: + case IF_PORT_100BASETX: + e100_set_speed(dev, 100); + e100_set_duplex(dev, autoneg); + break; ++ + case IF_PORT_100BASEFX: + case IF_PORT_10BASE2: + case IF_PORT_AUI: + spin_unlock(&np->lock); + return -EOPNOTSUPP; + break; ++ + default: + printk(KERN_ERR "%s: Invalid media selected", dev->name); + spin_unlock(&np->lock); +@@ -1602,6 +1515,7 @@ + update_rx_stats(struct net_device_stats *es) + { + unsigned long r = *R_REC_COUNTERS; ++ + /* update stats relevant to reception errors */ + es->rx_fifo_errors += IO_EXTRACT(R_REC_COUNTERS, congestion, r); + es->rx_crc_errors += IO_EXTRACT(R_REC_COUNTERS, crc_error, r); +@@ -1613,11 +1527,11 @@ + update_tx_stats(struct net_device_stats *es) + { + unsigned long r = *R_TR_COUNTERS; ++ + /* update stats relevant to transmission errors */ + es->collisions += + IO_EXTRACT(R_TR_COUNTERS, single_col, r) + + IO_EXTRACT(R_TR_COUNTERS, multiple_col, r); +- es->tx_errors += IO_EXTRACT(R_TR_COUNTERS, deferred, r); + } + + /* +@@ -1627,8 +1541,9 @@ + static struct net_device_stats * + e100_get_stats(struct net_device *dev) + { +- struct net_local *lp = (struct net_local *)dev->priv; ++ struct net_local *lp = netdev_priv(dev); + unsigned long flags; ++ + spin_lock_irqsave(&lp->lock, flags); + + update_rx_stats(&lp->stats); +@@ -1640,21 +1555,21 @@ + + /* + * Set or clear the multicast filter for this adaptor. +- * num_addrs == -1 Promiscuous mode, receive all packets +- * num_addrs == 0 Normal mode, clear multicast list +- * num_addrs > 0 Multicast mode, receive normal and MC packets, +- * and do best-effort filtering. ++ * num_addrs == -1 Promiscuous mode, receive all packets ++ * num_addrs == 0 Normal mode, clear multicast list ++ * num_addrs > 0 Multicast mode, receive normal and MC packets, ++ * and do best-effort filtering. + */ + static void + set_multicast_list(struct net_device *dev) + { +- struct net_local *lp = (struct net_local *)dev->priv; ++ struct net_local *lp = netdev_priv(dev); + int num_addr = dev->mc_count; + unsigned long int lo_bits; + unsigned long int hi_bits; ++ + spin_lock(&lp->lock); +- if (dev->flags & IFF_PROMISC) +- { ++ if (dev->flags & IFF_PROMISC) { + /* promiscuous mode */ + lo_bits = 0xfffffffful; + hi_bits = 0xfffffffful; +@@ -1684,9 +1599,10 @@ + struct dev_mc_list *dmi = dev->mc_list; + int i; + char *baddr; ++ + lo_bits = 0x00000000ul; + hi_bits = 0x00000000ul; +- for (i=0; i<num_addr; i++) { ++ for (i = 0; i < num_addr; i++) { + /* Calculate the hash index for the GA registers */ + + hash_ix = 0; +@@ -1713,8 +1629,7 @@ + + if (hash_ix >= 32) { + hi_bits |= (1 << (hash_ix-32)); +- } +- else { ++ } else { + lo_bits |= (1 << hash_ix); + } + dmi = dmi->next; +@@ -1729,10 +1644,11 @@ + } + + void +-e100_hardware_send_packet(char *buf, int length) ++e100_hardware_send_packet(struct net_local *np, char *buf, int length) + { + D(printk("e100 send pack, buf 0x%x len %d\n", buf, length)); + ++ spin_lock(&np->led_lock); + if (!led_active && time_after(jiffies, led_next_time)) { + /* light the network leds depending on the current speed. */ + e100_set_network_leds(NETWORK_ACTIVITY); +@@ -1742,15 +1658,16 @@ + led_active = 1; + mod_timer(&clear_led_timer, jiffies + HZ/10); + } ++ spin_unlock(&np->led_lock); + + /* configure the tx dma descriptor */ + myNextTxDesc->descr.sw_len = length; + myNextTxDesc->descr.ctrl = d_eop | d_eol | d_wait; + myNextTxDesc->descr.buf = virt_to_phys(buf); + +- /* Move end of list */ +- myLastTxDesc->descr.ctrl &= ~d_eol; +- myLastTxDesc = myNextTxDesc; ++ /* Move end of list */ ++ myLastTxDesc->descr.ctrl &= ~d_eol; ++ myLastTxDesc = myNextTxDesc; + + /* Restart DMA channel */ + *R_DMA_CH0_CMD = IO_STATE(R_DMA_CH0_CMD, cmd, restart); +@@ -1759,6 +1676,11 @@ + static void + e100_clear_network_leds(unsigned long dummy) + { ++ struct net_device *dev = (struct net_device *)dummy; ++ struct net_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->led_lock); ++ + if (led_active && time_after(jiffies, led_next_time)) { + e100_set_network_leds(NO_NETWORK_ACTIVITY); + +@@ -1766,6 +1688,8 @@ + led_next_time = jiffies + NET_FLASH_PAUSE; + led_active = 0; + } ++ ++ spin_unlock(&np->led_lock); + } + + static void +@@ -1786,19 +1710,25 @@ + #else + LED_NETWORK_SET(LED_OFF); + #endif +- } +- else if (light_leds) { ++ } else if (light_leds) { + if (current_speed == 10) { + LED_NETWORK_SET(LED_ORANGE); + } else { + LED_NETWORK_SET(LED_GREEN); + } +- } +- else { ++ } else { + LED_NETWORK_SET(LED_OFF); + } + } + ++#ifdef CONFIG_NET_POLL_CONTROLLER ++static void ++e100_netpoll(struct net_device* netdev) ++{ ++ e100rxtx_interrupt(NETWORK_DMA_TX_IRQ_NBR, netdev, NULL); ++} ++#endif ++ + static int + etrax_init_module(void) + { +diff -urN linux-2.6.19.2.orig/drivers/net/cris/eth_v32.c linux-2.6.19.2.dev/drivers/net/cris/eth_v32.c +--- linux-2.6.19.2.orig/drivers/net/cris/eth_v32.c 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/net/cris/eth_v32.c 2007-02-06 11:10:37.000000000 +0100 +@@ -0,0 +1,2305 @@ ++/* ++ * Driver for the ETRAX FS network controller. ++ * ++ * Copyright (c) 2003-2006 Axis Communications AB. ++ */ ++ ++#include <linux/module.h> ++ ++#include <linux/kernel.h> ++#include <linux/sched.h> ++#include <linux/delay.h> ++#include <linux/types.h> ++#include <linux/fcntl.h> ++#include <linux/interrupt.h> ++#include <linux/ptrace.h> ++#include <linux/ioport.h> ++#include <linux/in.h> ++#include <linux/slab.h> ++#include <linux/string.h> ++#include <linux/spinlock.h> ++#include <linux/errno.h> ++#include <linux/init.h> ++#include <linux/cpufreq.h> ++ ++#include <linux/netdevice.h> ++#include <linux/etherdevice.h> ++#include <linux/skbuff.h> ++#include <linux/ethtool.h> ++#include <linux/mii.h> ++ ++#include <asm/io.h> /* LED_* I/O functions */ ++#include <asm/irq.h> ++#include <asm/arch/hwregs/reg_map.h> ++#include <asm/arch/hwregs/reg_rdwr.h> ++#include <asm/arch/hwregs/dma.h> ++#include <asm/arch/hwregs/eth_defs.h> ++#include <asm/arch/hwregs/config_defs.h> ++#include <asm/arch/hwregs/intr_vect_defs.h> ++#include <asm/system.h> ++#include <asm/bitops.h> ++#include <asm/ethernet.h> ++#include <asm/arch/dma.h> ++#include <asm/arch/intmem.h> ++#include <asm/arch/pinmux.h> ++ ++#include "eth_v32.h" ++ ++#define DEBUG(x) ++#define GET_BIT(bit,val) (((val) >> (bit)) & 0x01) ++ ++/* Toggle network LEDs on/off at runtime */ ++static int use_network_leds = 1; ++ ++static void update_rx_stats(struct crisv32_ethernet_local *np); ++static void update_tx_stats(struct crisv32_ethernet_local *np); ++static void crisv32_eth_setup_controller(struct net_device *dev); ++static int crisv32_eth_request_irqdma(struct net_device *dev); ++static void crisv32_eth_init_rings(struct net_device *dev); ++static void crisv32_eth_reset_rings(struct net_device *dev); ++static void crisv32_ethernet_bug(struct net_device *dev); ++ ++/* ++ * The name of the card. Is used for messages and in the requests for ++ * io regions, irqs and dma channels. ++ */ ++static const char *cardname = "ETRAX FS built-in ethernet controller"; ++ ++static int autoneg_normal = 1; ++ ++/* Some chipset needs special care. */ ++struct transceiver_ops transceivers[] = { ++ {0x1018, broadcom_check_speed, broadcom_check_duplex}, ++ /* TDK 2120 and TDK 2120C */ ++ {0xC039, tdk_check_speed, tdk_check_duplex}, ++ {0x039C, tdk_check_speed, tdk_check_duplex}, ++ /* Intel LXT972A*/ ++ {0x04de, intel_check_speed, intel_check_duplex}, ++ /* National Semiconductor DP83865 */ ++ {0x0017, national_check_speed, national_check_duplex}, ++ /* Generic, must be last. */ ++ {0x0000, generic_check_speed, generic_check_duplex} ++}; ++ ++static struct net_device *crisv32_dev[2]; ++static struct crisv32_eth_leds *crisv32_leds[3]; ++ ++#ifdef CONFIG_CPU_FREQ ++static int ++crisv32_ethernet_freq_notifier(struct notifier_block *nb, unsigned long val, ++ void *data); ++ ++static struct notifier_block crisv32_ethernet_freq_notifier_block = { ++ .notifier_call = crisv32_ethernet_freq_notifier ++}; ++#endif ++ ++/* ++ * mask in and out tx/rx interrupts. ++ */ ++static inline void crisv32_disable_tx_ints(struct crisv32_ethernet_local *np) ++{ ++ reg_dma_rw_intr_mask intr_mask_tx = { .data = regk_dma_no }; ++ REG_WR(dma, np->dma_out_inst, rw_intr_mask, intr_mask_tx); ++} ++ ++static inline void crisv32_enable_tx_ints(struct crisv32_ethernet_local *np) ++{ ++ reg_dma_rw_intr_mask intr_mask_tx = { .data = regk_dma_yes }; ++ REG_WR(dma, np->dma_out_inst, rw_intr_mask, intr_mask_tx); ++} ++ ++static inline void crisv32_disable_rx_ints(struct crisv32_ethernet_local *np) ++{ ++ reg_dma_rw_intr_mask intr_mask_rx = { .in_eop = regk_dma_no }; ++ REG_WR(dma, np->dma_in_inst, rw_intr_mask, intr_mask_rx); ++} ++ ++static inline void crisv32_enable_rx_ints(struct crisv32_ethernet_local *np) ++{ ++ reg_dma_rw_intr_mask intr_mask_rx = { .in_eop = regk_dma_yes }; ++ REG_WR(dma, np->dma_in_inst, rw_intr_mask, intr_mask_rx); ++} ++ ++/* start/stop receiver */ ++static inline void crisv32_start_receiver(struct crisv32_ethernet_local *np) ++{ ++ reg_eth_rw_rec_ctrl rec_ctrl; ++ ++ rec_ctrl = REG_RD(eth, np->eth_inst, rw_rec_ctrl); ++ rec_ctrl.ma0 = regk_eth_yes; ++ rec_ctrl.broadcast = regk_eth_rec; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++} ++ ++static inline void crisv32_stop_receiver(struct crisv32_ethernet_local *np) ++{ ++ reg_eth_rw_rec_ctrl rec_ctrl; ++ ++ rec_ctrl = REG_RD(eth, np->eth_inst, rw_rec_ctrl); ++ rec_ctrl.ma0 = regk_eth_no; ++ rec_ctrl.broadcast = regk_eth_discard; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++} ++ ++static int __init ++crisv32_eth_request_irqdma(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Allocate IRQs and DMAs. */ ++ if (np->eth_inst == regi_eth0) { ++ if (request_irq(DMA0_INTR_VECT, crisv32tx_eth_interrupt, ++ 0, cardname, dev)) { ++ return -EAGAIN; ++ } ++ ++ if (request_irq(DMA1_INTR_VECT, crisv32rx_eth_interrupt, ++ IRQF_SAMPLE_RANDOM, cardname, dev)) { ++ goto err0_1; ++ } ++ ++ if (crisv32_request_dma(0, cardname, DMA_VERBOSE_ON_ERROR, ++ 12500000, dma_eth0)) ++ goto err0_2; ++ ++ if (crisv32_request_dma(1, cardname, DMA_VERBOSE_ON_ERROR, ++ 12500000, dma_eth0)) ++ goto err0_3; ++ ++ if (request_irq(ETH0_INTR_VECT, crisv32nw_eth_interrupt, 0, ++ cardname, dev)) { ++ crisv32_free_dma(1); ++ err0_3: ++ crisv32_free_dma(0); ++ err0_2: ++ free_irq(DMA1_INTR_VECT, dev); ++ err0_1: ++ free_irq(DMA0_INTR_VECT, dev); ++ return -EAGAIN; ++ } ++ } else { ++ if (request_irq(DMA6_INTR_VECT, crisv32tx_eth_interrupt, ++ 0, cardname, dev)) ++ return -EAGAIN; ++ ++ if (request_irq(DMA7_INTR_VECT, crisv32rx_eth_interrupt, ++ IRQF_SAMPLE_RANDOM, cardname, dev)) ++ goto err1_1; ++ ++ if (crisv32_request_dma(6, cardname, DMA_VERBOSE_ON_ERROR, ++ 0, dma_eth1)) ++ goto err1_2; ++ ++ if (crisv32_request_dma(7, cardname, DMA_VERBOSE_ON_ERROR, ++ 0, dma_eth1)) ++ goto err1_3; ++ ++ if (request_irq(ETH1_INTR_VECT, crisv32nw_eth_interrupt, 0, ++ cardname, dev)) { ++ crisv32_free_dma(7); ++ err1_3: ++ crisv32_free_dma(6); ++ err1_2: ++ free_irq(DMA7_INTR_VECT, dev); ++ err1_1: ++ free_irq(DMA6_INTR_VECT, dev); ++ return -EAGAIN; ++ } ++ } ++ return 0; ++} ++ ++static void __init ++crisv32_eth_setup_controller(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ reg_config_rw_pad_ctrl pad_ctrl; ++ ++ reg_eth_rw_tr_ctrl tr_ctrl = { ++ .retry = regk_eth_yes, ++ .pad = regk_eth_yes, ++ .crc = regk_eth_yes ++ }; ++ ++ reg_eth_rw_rec_ctrl rec_ctrl = { ++ .ma0 = regk_eth_no, /* enable at open() */ ++ .broadcast = regk_eth_no, ++ .max_size = regk_eth_size1522 ++ }; ++ ++ reg_eth_rw_ga_lo ga_lo = { 0 }; ++ reg_eth_rw_ga_hi ga_hi = { 0 }; ++ ++ reg_eth_rw_gen_ctrl gen_ctrl = { ++ .phy = regk_eth_mii_clk, ++ .flow_ctrl = regk_eth_yes ++ }; ++ ++ /* ++ * Initialize group address registers to make sure that no ++ * unwanted addresses are matched. ++ */ ++ REG_WR(eth, np->eth_inst, rw_ga_lo, ga_lo); ++ REG_WR(eth, np->eth_inst, rw_ga_hi, ga_hi); ++ ++ /* Configure receiver and transmitter */ ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ REG_WR(eth, np->eth_inst, rw_tr_ctrl, tr_ctrl); ++ ++ /* Enable ethernet controller with mii clk. */ ++ REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl); ++ gen_ctrl.en = regk_eth_yes; ++ REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl); ++ ++ /* keep reset low (RESET_LEN) */ ++ udelay(500); ++ ++ /* done */ ++ pad_ctrl = REG_RD(config, regi_config, rw_pad_ctrl); ++ pad_ctrl.phyrst_n = 1; ++ REG_WR(config, regi_config, rw_pad_ctrl, pad_ctrl); ++ ++ /* Let the PHY reset (RESET_WAIT) */ ++ udelay(200); ++ ++ crisv32_eth_probe_transceiver(dev); ++} ++ ++static void __init ++crisv32_eth_init_rings(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ int i; ++ ++ /* Initialise receive descriptors for interface. */ ++ for (i = 0; i < NBR_RX_DESC; i++) { ++ struct sk_buff *skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE); ++ ++ np->dma_rx_descr_list[i].skb = skb; ++ np->dma_rx_descr_list[i].descr.buf = ++ (char*)virt_to_phys(skb->data); ++ np->dma_rx_descr_list[i].descr.after = ++ (char*)virt_to_phys(skb->data + MAX_MEDIA_DATA_SIZE); ++ ++ np->dma_rx_descr_list[i].descr.eol = 0; ++ np->dma_rx_descr_list[i].descr.in_eop = 0; ++ np->dma_rx_descr_list[i].descr.next = ++ (void *) virt_to_phys(&np->dma_rx_descr_list[i + 1].descr); ++ } ++ /* bend the list into a ring */ ++ np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.next = ++ (void *) virt_to_phys(&np->dma_rx_descr_list[0].descr); ++ ++ /* Initialize transmit descriptors. */ ++ for (i = 0; i < NBR_TX_DESC; i++) { ++ np->dma_tx_descr_list[i].descr.wait = 1; ++ np->dma_tx_descr_list[i].descr.eol = 0; ++ np->dma_tx_descr_list[i].descr.out_eop = 0; ++ np->dma_tx_descr_list[i].descr.next = ++ (void*)virt_to_phys(&np->dma_tx_descr_list[i+1].descr); ++ } ++ /* bend the list into a ring */ ++ np->dma_tx_descr_list[NBR_TX_DESC - 1].descr.next = ++ (void *) virt_to_phys(&np->dma_tx_descr_list[0].descr); ++ ++ crisv32_eth_reset_rings(dev); ++} ++ ++static void ++crisv32_eth_reset_rings(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ int i; ++ ++ /* free un-handled tx packets */ ++ while(np->txpackets ++ || np->catch_tx_desc != np->active_tx_desc) { ++ np->txpackets--; ++ if (np->catch_tx_desc->skb) ++ dev_kfree_skb(np->catch_tx_desc->skb); ++ ++ np->catch_tx_desc->skb = 0; ++ np->catch_tx_desc = ++ phys_to_virt((int)np->catch_tx_desc->descr.next); ++ } while (np->catch_tx_desc != np->active_tx_desc); ++ WARN_ON(np->txpackets != 0); ++ np->txpackets = 0; ++ ++ /* cleanup the rx-ring */ ++ for (i = 0; i < NBR_RX_DESC; i++) { ++ struct sk_buff *skb; ++ skb = np->dma_rx_descr_list[i].skb; ++ if (!skb ++ || (np->dma_rx_descr_list[i].descr.buf != ++ (void *)virt_to_phys(skb->data))) ++ { ++ printk("%s:%d: damaged rx-ring! " ++ "i=%d skb=%p %lx %lx %p %p\n", ++ __func__, __LINE__, i, ++ skb, ++ virt_to_phys(skb->data), ++ virt_to_phys(skb->data + MAX_MEDIA_DATA_SIZE), ++ np->dma_rx_descr_list[i].descr.buf, ++ np->dma_rx_descr_list[i].descr.after); ++ WARN_ON(1); ++ crisv32_ethernet_bug(dev); ++ if (skb) ++ dev_kfree_skb(skb); ++ skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE); ++ np->dma_rx_descr_list[i].skb = skb; ++ np->dma_rx_descr_list[i].descr.buf = ++ (char*)virt_to_phys(skb->data); ++ } ++ np->dma_rx_descr_list[i].descr.after = ++ (char*)virt_to_phys(skb->data ++ + MAX_MEDIA_DATA_SIZE); ++ np->dma_rx_descr_list[i].descr.eol = 0; ++ np->dma_rx_descr_list[i].descr.in_eop = 0; ++ /* Workaround cache bug */ ++ flush_dma_descr(&np->dma_rx_descr_list[i].descr, 1); ++ } ++ ++ /* reset rx-ring */ ++ np->active_rx_desc = &np->dma_rx_descr_list[0]; ++ np->prev_rx_desc = &np->dma_rx_descr_list[NBR_RX_DESC - 1]; ++ np->last_rx_desc = np->prev_rx_desc; ++ np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.eol = 1; ++ ++ /* reset tx-ring */ ++ np->dma_tx_descr_list[0].descr.buf = ++ np->dma_tx_descr_list[0].descr.after = 0; ++ np->dma_rx_descr_list[i].descr.in_eop = 0; ++ np->dma_tx_descr_list[0].descr.eol = 1; ++ ++ np->active_tx_desc = &np->dma_tx_descr_list[0]; ++ np->prev_tx_desc = &np->dma_tx_descr_list[NBR_TX_DESC - 1]; ++ np->catch_tx_desc = &np->dma_tx_descr_list[0]; ++ ++ /* Fill context descriptors. */ ++ np->ctxt_in.next = 0; ++ np->ctxt_in.saved_data = ++ (void *)virt_to_phys(&np->active_rx_desc->descr); ++ np->ctxt_in.saved_data_buf = np->active_rx_desc->descr.buf; ++ ++ np->ctxt_out.next = 0; ++ np->ctxt_out.saved_data = ++ (void *)virt_to_phys(&np->dma_tx_descr_list[0].descr); ++} ++ ++static void __init ++crisv32_init_leds(int ledgrp, struct net_device* dev) ++{ ++ struct timer_list timer_init = TIMER_INITIALIZER(NULL, 0, 0); ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Use already allocated led grp if initialized */ ++ if (crisv32_leds[ledgrp] != NULL) { ++ np->leds = crisv32_leds[ledgrp]; ++ return; ++ } ++ ++ crisv32_leds[ledgrp] = kmalloc(sizeof(struct crisv32_eth_leds),GFP_KERNEL); ++ ++ crisv32_leds[ledgrp]->ledgrp = ledgrp; ++ crisv32_leds[ledgrp]->led_active = 0; ++ /* NOTE: Should this value be set to zero as the jiffies timer can wrap? */ ++ crisv32_leds[ledgrp]->led_next_time = jiffies; ++ ++ crisv32_leds[ledgrp]->clear_led_timer = timer_init; ++ crisv32_leds[ledgrp]->clear_led_timer.function = crisv32_clear_network_leds; ++ crisv32_leds[ledgrp]->clear_led_timer.data = (unsigned long) dev; ++ ++ spin_lock_init(&crisv32_leds[ledgrp]->led_lock); ++ ++ np->leds = crisv32_leds[ledgrp]; ++} ++ ++static int __init ++crisv32_ethernet_init(void) ++{ ++ struct crisv32_ethernet_local *np; ++ int ret = 0; ++ ++ printk("ETRAX FS 10/100MBit ethernet v0.01 (c)" ++ " 2003 Axis Communications AB\n"); ++ ++#ifdef CONFIG_ETRAX_ETHERNET_IFACE0 ++{ ++ int iface0 = 0; ++ /* Default MAC address for interface 0. ++ * The real one will be set later. */ ++ static struct sockaddr default_mac_iface0 = ++ {0, {0x00, 0x40, 0x8C, 0xCD, 0x00, 0x00}}; ++ ++ if (!(crisv32_dev[iface0] = alloc_etherdev(sizeof *np))) ++ return -ENOMEM; ++ ++ ret |= crisv32_ethernet_device_init(crisv32_dev[iface0]); ++ ++#if defined(CONFIG_ETRAX_ETH0_USE_LEDGRP0) ++ crisv32_init_leds(LED_GRP_0,crisv32_dev[iface0]); ++#elif defined(CONFIG_ETRAX_ETH0_USE_LEDGRP1) ++ crisv32_init_leds(LED_GRP_1,crisv32_dev[iface0]); ++#else ++ crisv32_init_leds(LED_GRP_NONE,crisv32_dev[iface0]); ++#endif ++ ++ np = (struct crisv32_ethernet_local *) crisv32_dev[iface0]->priv; ++ np->eth_inst = regi_eth0; ++ np->dma_out_inst = regi_dma0; ++ np->dma_in_inst = regi_dma1; ++ ++ register_netdev(crisv32_dev[iface0]); ++ ++ /* Set up default MAC address */ ++ memcpy(crisv32_dev[iface0]->dev_addr, default_mac_iface0.sa_data, 6); ++ crisv32_eth_set_mac_address(crisv32_dev[iface0], &default_mac_iface0); ++ if (crisv32_eth_request_irqdma(crisv32_dev[iface0])) ++ printk("%s: eth0 unable to allocate IRQ and DMA resources\n", ++ __func__); ++ np->txpackets = 0; ++ crisv32_eth_init_rings(crisv32_dev[iface0]); ++ crisv32_eth_setup_controller(crisv32_dev[iface0]); ++} ++#endif /* CONFIG_ETRAX_ETHERNET_IFACE0 */ ++ ++#ifdef CONFIG_ETRAX_ETHERNET_IFACE1 ++{ ++ int iface1 = 0; ++ /* Default MAC address for interface 1. ++ * The real one will be set later. */ ++ static struct sockaddr default_mac_iface1 = ++ {0, {0x00, 0x40, 0x8C, 0xCD, 0x00, 0x01}}; ++ ++ if (crisv32_pinmux_alloc_fixed(pinmux_eth1)) ++ panic("Eth pinmux\n"); ++ ++ /* Increase index to device array if interface 0 is enabled as well.*/ ++#ifdef CONFIG_ETRAX_ETHERNET_IFACE0 ++ iface1++; ++#endif ++ if (!(crisv32_dev[iface1] = alloc_etherdev(sizeof *np))) ++ return -ENOMEM; ++ ++ ret |= crisv32_ethernet_device_init(crisv32_dev[iface1]); ++ ++#if defined(CONFIG_ETRAX_ETH1_USE_LEDGRP0) ++ crisv32_init_leds(LED_GRP_0,crisv32_dev[iface1]); ++#elif defined(CONFIG_ETRAX_ETH1_USE_LEDGRP1) ++ crisv32_init_leds(LED_GRP_1,crisv32_dev[iface1]); ++#else ++ crisv32_init_leds(LED_GRP_NONE,crisv32_dev[iface1]); ++#endif ++ ++ np = (struct crisv32_ethernet_local *) crisv32_dev[iface1]->priv; ++ np->eth_inst = regi_eth1; ++ np->dma_out_inst = regi_dma6; ++ np->dma_in_inst = regi_dma7; ++ ++ register_netdev(crisv32_dev[iface1]); ++ ++ /* Set up default MAC address */ ++ memcpy(crisv32_dev[iface1]->dev_addr, default_mac_iface1.sa_data, 6); ++ crisv32_eth_set_mac_address(crisv32_dev[iface1], &default_mac_iface1); ++ ++ if (crisv32_eth_request_irqdma(crisv32_dev[iface1])) ++ printk("%s: eth1 unable to allocate IRQ and DMA resources\n", ++ __func__); ++ np->txpackets = 0; ++ crisv32_eth_init_rings(crisv32_dev[iface1]); ++ crisv32_eth_setup_controller(crisv32_dev[iface1]); ++} ++#endif /* CONFIG_ETRAX_ETHERNET_IFACE1 */ ++ ++#ifdef CONFIG_CPU_FREQ ++ cpufreq_register_notifier(&crisv32_ethernet_freq_notifier_block, ++ CPUFREQ_TRANSITION_NOTIFIER); ++#endif ++ ++ return ret; ++} ++ ++static int __init ++crisv32_ethernet_device_init(struct net_device* dev) ++{ ++ struct timer_list timer_init = TIMER_INITIALIZER(NULL, 0, 0); ++ struct crisv32_ethernet_local *np; ++ ++ dev->base_addr = 0; /* Just to have something to show. */ ++ ++ /* we do our own locking */ ++ dev->features |= NETIF_F_LLTX; ++ ++ /* We use several IRQs and DMAs so just report 0 here. */ ++ dev->irq = 0; ++ dev->dma = 0; ++ ++ /* ++ * Fill in our handlers so the network layer can talk to us in the ++ * future. ++ */ ++ dev->open = crisv32_eth_open; ++ dev->hard_start_xmit = crisv32_eth_send_packet; ++ dev->stop = crisv32_eth_close; ++ dev->get_stats = crisv32_get_stats; ++ dev->set_multicast_list = crisv32_eth_set_multicast_list; ++ dev->set_mac_address = crisv32_eth_set_mac_address; ++ dev->ethtool_ops = &crisv32_ethtool_ops; ++ dev->do_ioctl = crisv32_eth_ioctl; ++ dev->set_config = crisv32_eth_set_config; ++ dev->tx_timeout = crisv32_eth_tx_timeout; ++#ifdef CONFIG_NET_POLL_CONTROLLER ++ dev->poll_controller = crisv32_netpoll; ++#endif ++ ++ np = netdev_priv(dev); ++ ++ spin_lock_init(&np->lock); ++ spin_lock_init(&np->transceiver_lock); ++ ++ /* Initialize speed indicator stuff. */ ++ np->current_speed = 10; ++ np->current_speed_selection = 0; /* Auto. */ ++ np->speed_timer = timer_init; ++ np->speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL; ++ np->speed_timer.data = (unsigned long) dev; ++ np->speed_timer.function = crisv32_eth_check_speed; ++ ++ np->full_duplex = 0; ++ np->current_duplex = autoneg; ++ np->duplex_timer = timer_init; ++ np->duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL; ++ np->duplex_timer.data = (unsigned long) dev; ++ np->duplex_timer.function = crisv32_eth_check_duplex; ++ ++ return 0; ++} ++ ++static int ++crisv32_eth_open(struct net_device *dev) ++{ ++ struct sockaddr mac_addr; ++ reg_dma_rw_ack_intr ack_intr = { .data = 1,.in_eop = 1 }; ++ reg_dma_rw_cfg dma_cfg = { .en = 1 }; ++ reg_eth_rw_clr_err clr_err = {.clr = regk_eth_yes}; ++ int intr_mask_nw = 0x1cff; ++ int eth_ack_intr = 0xffff; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->lock); ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ np->gigabit_mode = 0; ++#endif ++ crisv32_disable_tx_ints(np); ++ crisv32_disable_rx_ints(np); ++ ++ REG_WR(eth, np->eth_inst, rw_clr_err, clr_err); ++ REG_WR_INT(eth, np->eth_inst, rw_ack_intr, eth_ack_intr); ++ REG_WR_INT(eth, np->eth_inst, rw_intr_mask, intr_mask_nw); ++ crisv32_eth_reset_rings(dev); ++ ++ /* Give the hardware an idea of what MAC address we want. */ ++ memcpy(mac_addr.sa_data, dev->dev_addr, dev->addr_len); ++ crisv32_eth_set_mac_address(dev, &mac_addr); ++ ++ /* Enable irq and make sure that the irqs are cleared. */ ++ REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr); ++ REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr); ++ ++ /* Prepare input DMA. */ ++ DMA_RESET(np->dma_in_inst); ++ DMA_ENABLE(np->dma_in_inst); ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ DMA_WR_CMD(np->dma_in_inst, regk_dma_set_w_size2); ++#endif ++ DMA_START_CONTEXT( np->dma_in_inst, virt_to_phys(&np->ctxt_in)); ++ DMA_CONTINUE(np->dma_in_inst); ++ crisv32_enable_rx_ints(np); ++ crisv32_start_receiver(np); ++ ++ /* Prepare output DMA. */ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ DMA_WR_CMD(np->dma_out_inst, regk_dma_set_w_size4); ++#endif ++ REG_WR(dma, np->dma_out_inst, rw_cfg, dma_cfg); ++ netif_start_queue(dev); ++ crisv32_enable_tx_ints(np); ++ ++ /* Start duplex/speed timers */ ++ add_timer(&np->speed_timer); ++ add_timer(&np->duplex_timer); ++ ++ spin_unlock(&np->lock); ++ /* ++ * We are now ready to accept transmit requeusts from the queueing ++ * layer of the networking. ++ */ ++ netif_carrier_on(dev); ++ ++ return 0; ++} ++ ++static int ++crisv32_eth_close(struct net_device *dev) ++{ ++ reg_dma_rw_ack_intr ack_intr = {0}; ++ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ unsigned long flags; ++ ++ printk(KERN_INFO "Closing %s.\n", dev->name); ++ ++ /* stop the receiver before the DMA channels to avoid overruns. */ ++ crisv32_stop_receiver(np); ++ ++ spin_lock_irqsave(&np->lock, flags); ++ netif_stop_queue(dev); ++ ++ /* Reset the TX DMA in case it has hung on something. */ ++ DMA_RESET(np->dma_in_inst); ++ ++ /* Stop DMA */ ++ DMA_STOP(np->dma_in_inst); ++ DMA_STOP(np->dma_out_inst); ++ ++ /* Disable irq and make sure that the irqs are cleared. */ ++ crisv32_disable_tx_ints(np); ++ ack_intr.data = 1; ++ REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr); ++ ++ crisv32_disable_rx_ints(np); ++ ack_intr.in_eop = 1; ++ REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr); ++ ++ np->sender_started = 0; ++ spin_unlock_irqrestore(&np->lock, flags); ++ ++ /* Update the statistics. */ ++ update_rx_stats(np); ++ update_tx_stats(np); ++ ++ /* Stop speed/duplex timers */ ++ del_timer(&np->speed_timer); ++ del_timer(&np->duplex_timer); ++ ++ return 0; ++} ++ ++static int ++crisv32_eth_set_mac_address(struct net_device *dev, void *vpntr) ++{ ++ int i; ++ unsigned char *addr = ((struct sockaddr*)vpntr)->sa_data; ++ ++ reg_eth_rw_ma0_lo ma0_lo = ++ { addr[0] | (addr[1] << 8) | (addr[2] << 16) | (addr[3] << 24)}; ++ ++ reg_eth_rw_ma0_hi ma0_hi = { addr[4] | (addr[5] << 8) }; ++ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Remember the address. */ ++ memcpy(dev->dev_addr, addr, dev->addr_len); ++ ++ /* ++ * Write the address to the hardware. ++ * Note the way the address is wrapped: ++ * ma0_l0 = a0_0 | (a0_1 << 8) | (a0_2 << 16) | (a0_3 << 24); ++ * ma0_hi = a0_4 | (a0_5 << 8); ++ */ ++ REG_WR(eth, np->eth_inst, rw_ma0_lo, ma0_lo); ++ REG_WR(eth, np->eth_inst, rw_ma0_hi, ma0_hi); ++ ++ printk(KERN_INFO "%s: changed MAC to ", dev->name); ++ ++ for (i = 0; i < 5; i++) ++ printk("%02X:", dev->dev_addr[i]); ++ ++ printk("%02X\n", dev->dev_addr[i]); ++ ++ return 0; ++} ++ ++static irqreturn_t ++crisv32rx_eth_interrupt(int irq, void *dev_id) ++{ ++ reg_dma_r_masked_intr masked_in; ++ reg_dma_rw_cmd cmd = {0}; ++ reg_dma_rw_ack_intr ack_intr = {0}; ++ struct net_device *dev = (struct net_device *) dev_id; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ masked_in = REG_RD(dma, np->dma_in_inst, r_masked_intr); ++ ++ if (masked_in.in_eop) { ++ DEBUG(printk("EOP_IN interrupt\n")); ++ ++ /* Acknowledge input dma interrupt. */ ++ ack_intr.in_eop = 1; ++ REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr); ++ ++ np->new_rx_package = 1; ++ /* Check if complete packets were indeed received. */ ++ while (np->active_rx_desc->descr.in_eop == 1 ++ && np->new_rx_package) { ++ /* ++ * Take out the buffer and give it to the OS, then ++ * allocate a new buffer to put a packet in. ++ */ ++ crisv32_eth_receive_packet(dev); ++ ++ /* Update number of packets received. */ ++ np->stats.rx_packets++; ++ ++ /* Restarts input dma. */ ++ cmd.cont_data = 1; ++ REG_WR(dma, np->dma_in_inst, rw_cmd, cmd); ++ ++ /* Acknowledge input dma interrupt. */ ++ REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr); ++ } ++ } ++ return IRQ_HANDLED; ++} ++ ++static irqreturn_t ++crisv32tx_eth_interrupt(int irq, void *dev_id) ++{ ++ reg_dma_rw_stat stat; ++ dma_descr_data *dma_pos; ++ reg_dma_rw_ack_intr ack_intr = { .data = 1 }; ++ reg_dma_r_masked_intr masked_out; ++ ++ struct net_device *dev = (struct net_device *) dev_id; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ unsigned long flags; ++ ++ masked_out = REG_RD(dma, np->dma_out_inst, r_masked_intr); ++ ++ /* Get the current output dma position. */ ++ stat = REG_RD(dma, np->dma_out_inst, rw_stat); ++ if (stat.list_state == regk_dma_data_at_eol) ++ dma_pos = &np->active_tx_desc->descr; ++ else ++ dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_out_inst, ++ rw_data)); ++ ++ /* ack the interrupt */ ++ REG_WR(dma, np->dma_out_inst, rw_ack_intr, ack_intr); ++ ++ /* protect against ethernet excessive-col interrupts */ ++ spin_lock_irqsave(&np->lock, flags); ++ ++ /* Take care of transmited dma descriptors and report sent packet. */ ++ while (np->txpackets && ((&np->catch_tx_desc->descr != dma_pos) ++ || netif_queue_stopped(dev))) { ++ /* Update sent packet statistics. */ ++ np->stats.tx_bytes += np->catch_tx_desc->skb->len; ++ np->stats.tx_packets++; ++ ++ dev_kfree_skb_irq(np->catch_tx_desc->skb); ++ np->catch_tx_desc->skb = 0; ++ np->txpackets--; ++ np->catch_tx_desc = ++ phys_to_virt((int)np->catch_tx_desc->descr.next); ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ if (np->gigabit_mode) { ++ np->intmem_tx_buf_catch->free = 1; ++ np->intmem_tx_buf_catch = np->intmem_tx_buf_catch->next; ++ } ++#endif ++ netif_wake_queue(dev); ++ } ++ spin_unlock_irqrestore(&np->lock, flags); ++ return IRQ_HANDLED; ++} ++ ++ ++/* Update receive errors. */ ++static void ++update_rx_stats(struct crisv32_ethernet_local *np) ++{ ++ reg_eth_rs_rec_cnt r; ++ reg_eth_rs_phy_cnt rp; ++ ++ r = REG_RD(eth, np->eth_inst, rs_rec_cnt); ++ rp = REG_RD(eth, np->eth_inst, rs_phy_cnt); ++ ++ np->stats.rx_fifo_errors += r.congestion; ++ np->stats.rx_crc_errors += r.crc_err; ++ np->stats.rx_frame_errors += r.align_err; ++ np->stats.rx_length_errors += r.oversize; ++} ++ ++/* Update transmit errors. */ ++static void ++update_tx_stats(struct crisv32_ethernet_local *np) ++{ ++ reg_eth_rs_tr_cnt r; ++ ++ r = REG_RD(eth, np->eth_inst, rs_tr_cnt); ++ ++ np->stats.collisions += r.single_col + r.mult_col; ++ np->stats.tx_errors += r.deferred; ++} ++ ++/* Get current statistics. */ ++static struct net_device_stats * ++crisv32_get_stats(struct net_device *dev) ++{ ++ unsigned long flags; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ spin_lock_irqsave(&np->lock, flags); ++ ++ update_rx_stats(np); ++ update_tx_stats(np); ++ ++ spin_unlock_irqrestore(&np->lock, flags); ++ ++ return &np->stats; ++} ++ ++/* Check for network errors. This acknowledge the received interrupt. */ ++static irqreturn_t ++crisv32nw_eth_interrupt(int irq, void *dev_id) ++{ ++ struct net_device *dev = (struct net_device *) dev_id; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ reg_eth_r_masked_intr intr_mask; ++ int ack_intr = 0xffff; ++ reg_eth_rw_clr_err clr_err; ++ ++ intr_mask = REG_RD(eth, np->eth_inst, r_masked_intr); ++ ++ /* ++ * Check for underrun and/or excessive collisions. Note that the ++ * rw_clr_err register clears both underrun and excessive collision ++ * errors, so there's no need to check them separately. ++ */ ++ if (np->sender_started ++ && (intr_mask.urun || intr_mask.exc_col)) { ++ unsigned long flags; ++ dma_descr_data *dma_pos; ++ reg_dma_rw_stat stat; ++ ++ /* Get the current output dma position. */ ++ stat = REG_RD(dma, np->dma_out_inst, rw_stat); ++ if (stat.list_state == regk_dma_data_at_eol) ++ dma_pos = &np->active_tx_desc->descr; ++ else ++ dma_pos = phys_to_virt(REG_RD_INT(dma, ++ np->dma_out_inst, ++ rw_data)); ++ ++ /* ++ * Protect against the tx-interrupt messing with ++ * the tx-ring. ++ */ ++ spin_lock_irqsave(&np->lock, flags); ++ /* ++ * If we have more than one packet in the tx-ring ++ * drop one and move ahead. Upper layers rely on ++ * packeloss when doing congestion control. ++ */ ++ if (intr_mask.exc_col && np->txpackets > 1) { ++ dev_kfree_skb_irq(np->catch_tx_desc->skb); ++ np->catch_tx_desc->skb = 0; ++ np->catch_tx_desc = ++ phys_to_virt((int) ++ np->catch_tx_desc->descr.next); ++ np->txpackets--; ++ netif_wake_queue(dev); ++ } ++ np->ctxt_out.next = 0; ++ if (np->txpackets) { ++ np->ctxt_out.saved_data = (void *) ++ virt_to_phys(&np->catch_tx_desc->descr); ++ np->ctxt_out.saved_data_buf = ++ np->catch_tx_desc->descr.buf; ++ ++ /* restart the DMA */ ++ DMA_START_CONTEXT(np->dma_out_inst, ++ (int) virt_to_phys(&np->ctxt_out)); ++ } ++ else { ++ /* let the next packet restart the DMA */ ++ np->ctxt_out.saved_data = (void *) ++ virt_to_phys(&np->active_tx_desc->descr); ++ np->sender_started = 0; ++ } ++ ++ spin_unlock_irqrestore(&np->lock, flags); ++ np->stats.tx_errors++; ++ } ++ ++ REG_WR_INT(eth, np->eth_inst, rw_ack_intr, ack_intr); ++ clr_err.clr = 1; ++ REG_WR(eth, np->eth_inst, rw_clr_err, clr_err); ++ ++ update_rx_stats(np); ++ update_tx_stats(np); ++ ++ return IRQ_HANDLED; ++} ++ ++/* We have a good packet(s), get it/them out of the buffers. */ ++static void ++crisv32_eth_receive_packet(struct net_device *dev) ++{ ++ int length; ++ struct sk_buff *skb; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ struct sk_buff *tmp; ++ unsigned long flags; ++ ++ DEBUG(printk("crisv32_receive_packet\n")); ++ ++ /* Activate LED */ ++ spin_lock_irqsave(&np->leds->led_lock, flags); ++ if (!np->leds->led_active && time_after(jiffies, np->leds->led_next_time)) { ++ /* light the network leds depending on the current speed. */ ++ crisv32_set_network_leds(LED_ACTIVITY, dev); ++ ++ /* Set the earliest time we may clear the LED */ ++ np->leds->led_next_time = jiffies + NET_FLASH_TIME; ++ np->leds->led_active = 1; ++ np->leds->clear_led_timer.data = (unsigned long) dev; ++ mod_timer(&np->leds->clear_led_timer, jiffies + HZ/10); ++ } ++ spin_unlock_irqrestore(&np->leds->led_lock, flags); ++ ++ /* Discard CRC (4 bytes). */ ++ length = (np->active_rx_desc->descr.after) - ++ (np->active_rx_desc->descr.buf) - 4; ++ ++ /* Update received packet statistics. */ ++ np->stats.rx_bytes += length; ++ ++ if (np->active_rx_desc != np->last_rx_desc) { ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ if (np->gigabit_mode) { ++ skb = dev_alloc_skb(length); ++ if(!skb) { ++ np->stats.rx_errors++; ++ printk(KERN_NOTICE "%s: memory squeeze," ++ " dropping packet.", dev->name); ++ return; ++ } ++ /* Allocate room for the packet body. */ ++ skb_put(skb, length - ETHER_HEAD_LEN); ++ /* Allocate room for the header and copy the data to ++ * the SKB */ ++ memcpy(skb_push(skb, ETHER_HEAD_LEN), ++ crisv32_intmem_phys_to_virt((unsigned long)np->active_rx_desc->descr.buf), length); ++ skb->dev = dev; ++ skb->protocol = eth_type_trans(skb, dev); ++ skb->ip_summed = CHECKSUM_NONE; ++ /* Send the packet to the upper layer. */ ++ netif_rx(skb); ++ np->last_rx_desc = ++ (void *) phys_to_virt(np->last_rx_desc->descr.next); ++ } else { ++#endif ++ tmp = dev_alloc_skb(MAX_MEDIA_DATA_SIZE); ++ if (!tmp) { ++ np->stats.rx_errors++; ++ printk(KERN_NOTICE "%s: memory squeeze," ++ " dropping packet.", ++ dev->name); ++ return; ++ } ++ skb = np->active_rx_desc->skb; ++ np->active_rx_desc->skb = tmp; ++ skb_put(skb, length); ++ ++ np->active_rx_desc->descr.buf = ++ (void *) virt_to_phys(np->active_rx_desc->skb->data); ++ np->active_rx_desc->descr.after = ++ np->active_rx_desc->descr.buf + MAX_MEDIA_DATA_SIZE; ++ ++ skb->dev = dev; ++ skb->protocol = eth_type_trans(skb, dev); ++ skb->ip_summed = CHECKSUM_NONE; ++ ++ /* Send the packet to the upper layer. */ ++ netif_rx(skb); ++ np->last_rx_desc = ++ phys_to_virt((int) ++ np->last_rx_desc->descr.next); ++ } ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ } ++#endif ++ /* ++ * When the input DMA reaches eol precaution must be taken, otherwise ++ * the DMA could stop. The problem occurs if the eol flag is re-placed ++ * on the descriptor that the DMA stands on before the DMA proceed to ++ * the next descriptor. This case could, for example, happen if there ++ * is a traffic burst and then the network goes silent. To prevent this ++ * we make sure that we do not set the eol flag on the descriptor that ++ * the DMA stands on. ++ */ ++ if(virt_to_phys(&np->active_rx_desc->descr) != ++ REG_RD_INT(dma, np->dma_in_inst, rw_saved_data)) { ++ np->active_rx_desc->descr.after = ++ np->active_rx_desc->descr.buf + MAX_MEDIA_DATA_SIZE; ++ np->active_rx_desc->descr.eol = 1; ++ np->active_rx_desc->descr.in_eop = 0; ++ np->active_rx_desc = ++ phys_to_virt((int)np->active_rx_desc->descr.next); ++ barrier(); ++ np->prev_rx_desc->descr.eol = 0; ++ flush_dma_descr(&np->prev_rx_desc->descr, 0); // Workaround cache bug ++ np->prev_rx_desc = ++ phys_to_virt((int)np->prev_rx_desc->descr.next); ++ flush_dma_descr(&np->prev_rx_desc->descr, 1); // Workaround cache bug ++ } else { ++ np->new_rx_package = 0; ++ } ++} ++ ++/* ++ * This function (i.e. hard_start_xmit) is protected from concurent calls by a ++ * spinlock (xmit_lock) in the net_device structure. ++ */ ++static int ++crisv32_eth_send_packet(struct sk_buff *skb, struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ unsigned char *buf = skb->data; ++ unsigned long flags; ++ ++ dev->trans_start = jiffies; ++ ++ spin_lock_irqsave(&np->leds->led_lock, flags); ++ if (!np->leds->led_active && time_after(jiffies, np->leds->led_next_time)) { ++ /* light the network leds depending on the current speed. */ ++ crisv32_set_network_leds(LED_ACTIVITY, dev); ++ ++ /* Set the earliest time we may clear the LED */ ++ np->leds->led_next_time = jiffies + NET_FLASH_TIME; ++ np->leds->led_active = 1; ++ np->leds->clear_led_timer.data = (unsigned long) dev; ++ mod_timer(&np->leds->clear_led_timer, jiffies + HZ/10); ++ } ++ spin_unlock_irqrestore(&np->leds->led_lock, flags); ++ ++ /* ++ * Need to disable irq to avoid updating pointer in interrupt while ++ * sending packets. ++ */ ++ spin_lock_irqsave(&np->lock, flags); ++ ++ np->active_tx_desc->skb = skb; ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ if (np->gigabit_mode) { ++ if(np->intmem_tx_buf_active->free) { ++ memcpy(np->intmem_tx_buf_active->buf, ++ skb->data, skb->len); ++ np->intmem_tx_buf_active->free = 0; ++ crisv32_eth_hw_send_packet( ++ np->intmem_tx_buf_active->buf, skb->len, np); ++ np->intmem_tx_buf_active = ++ np->intmem_tx_buf_active->next; ++ } else { ++ printk("%s: Internal tx memory buffer not free!\n\r", ++ __FILE__); ++ spin_unlock_irqrestore(&np->lock, flags); ++ return 1; ++ } ++ } ++ else ++#endif ++ { ++ crisv32_eth_hw_send_packet(buf, skb->len, np); ++ } ++ /* Stop queue if full. */ ++ if (np->active_tx_desc == np->catch_tx_desc) ++ netif_stop_queue(dev); ++ ++ np->txpackets++; ++ spin_unlock_irqrestore(&np->lock, flags); ++ ++ return 0; ++} ++ ++ ++static void ++crisv32_eth_hw_send_packet(unsigned char *buf, int length, void *priv) ++{ ++ struct crisv32_ethernet_local *np = ++ (struct crisv32_ethernet_local *) priv; ++ ++ /* Configure the tx dma descriptor. */ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ if (np->gigabit_mode) { ++ np->active_tx_desc->descr.buf = (unsigned char *) crisv32_intmem_virt_to_phys(buf); ++ } else ++#endif ++ { ++ np->active_tx_desc->descr.buf = (unsigned char *) virt_to_phys(buf); ++ } ++ ++ np->active_tx_desc->descr.after = np->active_tx_desc->descr.buf + ++ length; ++ np->active_tx_desc->descr.intr = 1; ++ np->active_tx_desc->descr.out_eop = 1; ++ ++ /* Move eol. */ ++ np->active_tx_desc->descr.eol = 1; ++ np->prev_tx_desc->descr.eol = 0; ++ ++ ++ /* Update pointers. */ ++ np->prev_tx_desc = np->active_tx_desc; ++ np->active_tx_desc = phys_to_virt((int)np->active_tx_desc->descr.next); ++ ++ /* Start DMA. */ ++ crisv32_start_dma_out(np); ++} ++ ++static void ++crisv32_start_dma_out(struct crisv32_ethernet_local* np) ++{ ++ if (!np->sender_started) { ++ /* Start DMA for the first time. */ ++ np->ctxt_out.saved_data_buf = np->prev_tx_desc->descr.buf; ++ REG_WR(dma, np->dma_out_inst, rw_group_down, ++ (int) virt_to_phys(&np->ctxt_out)); ++ DMA_WR_CMD(np->dma_out_inst, regk_dma_load_c); ++ DMA_WR_CMD(np->dma_out_inst, regk_dma_load_d | regk_dma_burst); ++ np->sender_started = 1; ++ } else { ++ DMA_CONTINUE_DATA(np->dma_out_inst); ++ } ++} ++ ++/* ++ * Called by upper layers if they decide it took too long to complete sending ++ * a packet - we need to reset and stuff. ++ */ ++static void ++crisv32_eth_tx_timeout(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ reg_dma_rw_cfg cfg = {0}; ++ reg_dma_rw_stat stat = {0}; ++ unsigned long flags; ++ ++ printk(KERN_WARNING "%s: transmit timed out\n", dev->name); ++ ++ ++ spin_lock_irqsave(&np->lock, flags); ++ crisv32_ethernet_bug(dev); ++ ++ np->txpackets = 0; ++ /* Update error stats. */ ++ np->stats.tx_errors++; ++ ++ /* Reset the TX DMA in case it has hung on something. */ ++ cfg.en = 0; ++ REG_WR(dma, np->dma_out_inst, rw_cfg, cfg); ++ ++ do { ++ stat = REG_RD(dma, np->dma_out_inst, rw_stat); ++ } while (stat.mode != regk_dma_rst); ++ ++ /* Reset the tranceiver. */ ++ crisv32_eth_reset_tranceiver(dev); ++ ++ /* Get rid of the packets that never got an interrupt. */ ++ do { ++ if (np->catch_tx_desc->skb) ++ dev_kfree_skb(np->catch_tx_desc->skb); ++ ++ np->catch_tx_desc->skb = 0; ++ np->catch_tx_desc = ++ phys_to_virt((int)np->catch_tx_desc->descr.next); ++ } while (np->catch_tx_desc != np->active_tx_desc); ++ ++ ++ /* Start output DMA. */ ++ REG_WR(dma, np->dma_out_inst, rw_group_down, ++ (int) virt_to_phys(&np->ctxt_out)); ++ DMA_WR_CMD(np->dma_out_inst, regk_dma_load_c); ++ DMA_WR_CMD(np->dma_out_inst, regk_dma_load_d | regk_dma_burst); ++ spin_unlock_irqrestore(&np->lock, flags); ++ ++ /* Tell the upper layers we're ok again. */ ++ netif_wake_queue(dev); ++} ++ ++/* ++ * Set or clear the multicast filter for this adaptor. ++ * num_addrs == -1 Promiscuous mode, receive all packets ++ * num_addrs == 0 Normal mode, clear multicast list ++ * num_addrs > 0 Multicast mode, receive normal and MC packets, ++ * and do best-effort filtering. ++ */ ++static void ++crisv32_eth_set_multicast_list(struct net_device *dev) ++{ ++ int num_addr = dev->mc_count; ++ unsigned long int lo_bits; ++ unsigned long int hi_bits; ++ reg_eth_rw_rec_ctrl rec_ctrl = {0}; ++ reg_eth_rw_ga_lo ga_lo = {0}; ++ reg_eth_rw_ga_hi ga_hi = {0}; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ if (dev->flags & IFF_PROMISC) { ++ /* Promiscuous mode. */ ++ lo_bits = 0xfffffffful; ++ hi_bits = 0xfffffffful; ++ ++ /* Enable individual receive. */ ++ rec_ctrl = (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, ++ rw_rec_ctrl); ++ rec_ctrl.individual = regk_eth_yes; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ } else if (dev->flags & IFF_ALLMULTI) { ++ /* Enable all multicasts. */ ++ lo_bits = 0xfffffffful; ++ hi_bits = 0xfffffffful; ++ ++ /* Disable individual receive */ ++ rec_ctrl = ++ (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl); ++ rec_ctrl.individual = regk_eth_no; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ } else if (num_addr == 0) { ++ /* Normal, clear the mc list. */ ++ lo_bits = 0x00000000ul; ++ hi_bits = 0x00000000ul; ++ ++ /* Disable individual receive */ ++ rec_ctrl = ++ (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl); ++ rec_ctrl.individual = regk_eth_no; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ } else { ++ /* MC mode, receive normal and MC packets. */ ++ char hash_ix; ++ struct dev_mc_list *dmi = dev->mc_list; ++ int i; ++ char *baddr; ++ lo_bits = 0x00000000ul; ++ hi_bits = 0x00000000ul; ++ ++ for (i = 0; i < num_addr; i++) { ++ /* Calculate the hash index for the GA registers. */ ++ hash_ix = 0; ++ baddr = dmi->dmi_addr; ++ hash_ix ^= (*baddr) & 0x3f; ++ hash_ix ^= ((*baddr) >> 6) & 0x03; ++ ++baddr; ++ hash_ix ^= ((*baddr) << 2) & 0x03c; ++ hash_ix ^= ((*baddr) >> 4) & 0xf; ++ ++baddr; ++ hash_ix ^= ((*baddr) << 4) & 0x30; ++ hash_ix ^= ((*baddr) >> 2) & 0x3f; ++ ++baddr; ++ hash_ix ^= (*baddr) & 0x3f; ++ hash_ix ^= ((*baddr) >> 6) & 0x03; ++ ++baddr; ++ hash_ix ^= ((*baddr) << 2) & 0x03c; ++ hash_ix ^= ((*baddr) >> 4) & 0xf; ++ ++baddr; ++ hash_ix ^= ((*baddr) << 4) & 0x30; ++ hash_ix ^= ((*baddr) >> 2) & 0x3f; ++ ++ hash_ix &= 0x3f; ++ ++ if (hash_ix > 32) ++ hi_bits |= (1 << (hash_ix - 32)); ++ else ++ lo_bits |= (1 << hash_ix); ++ ++ dmi = dmi->next; ++ } ++ ++ /* Disable individual receive. */ ++ rec_ctrl = ++ (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, rw_rec_ctrl); ++ rec_ctrl.individual = regk_eth_no; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ } ++ ++ ga_lo.tbl = (unsigned int) lo_bits; ++ ga_hi.tbl = (unsigned int) hi_bits; ++ ++ REG_WR(eth, np->eth_inst, rw_ga_lo, ga_lo); ++ REG_WR(eth, np->eth_inst, rw_ga_hi, ga_hi); ++} ++ ++static int ++crisv32_eth_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) ++{ ++ struct mii_ioctl_data *data = if_mii(ifr); ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ int old_autoneg; ++ ++ spin_lock(&np->lock); /* Preempt protection */ ++ switch (cmd) { ++ case SIOCGMIIPHY: /* Get PHY address */ ++ data->phy_id = np->mdio_phy_addr; ++ break; ++ case SIOCGMIIREG: /* Read MII register */ ++ data->val_out = crisv32_eth_get_mdio_reg(dev, ++ data->reg_num); ++ break; ++ case SIOCSMIIREG: /* Write MII register */ ++ crisv32_eth_set_mdio_reg(dev, data->reg_num, ++ data->val_in); ++ break; ++ case SET_ETH_ENABLE_LEDS: ++ use_network_leds = 1; ++ break; ++ case SET_ETH_DISABLE_LEDS: ++ use_network_leds = 0; ++ break; ++ case SET_ETH_AUTONEG: ++ old_autoneg = autoneg_normal; ++ autoneg_normal = *(int*)data; ++ if (autoneg_normal != old_autoneg) ++ crisv32_eth_negotiate(dev); ++ break; ++ default: ++ spin_unlock(&np->lock); /* Preempt protection */ ++ return -EINVAL; ++ } ++ spin_unlock(&np->lock); ++ return 0; ++} ++ ++static int crisv32_eth_get_settings(struct net_device *dev, ++ struct ethtool_cmd *ecmd) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ /* What about GMII and 1000xpause? not included in ethtool.h */ ++ ecmd->supported = SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII | ++ SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | ++ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full; ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ ecmd->supported |= SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full; ++#endif ++ ecmd->port = PORT_TP; ++ ecmd->transceiver = XCVR_EXTERNAL; ++ ecmd->phy_address = np->mdio_phy_addr; ++ ecmd->speed = np->current_speed; ++ ecmd->duplex = np->full_duplex; ++ ecmd->advertising = ADVERTISED_TP; ++ ++ if (np->current_duplex == autoneg && np->current_speed_selection == 0) ++ ecmd->advertising |= ADVERTISED_Autoneg; ++ else { ++ ecmd->advertising |= ++ ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | ++ ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full; ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ ecmd->advertising |= ADVERTISED_1000baseT_Half | ++ ADVERTISED_1000baseT_Full; ++#endif ++ if (np->current_speed_selection == 10) ++ ecmd->advertising &= ~(ADVERTISED_100baseT_Half | ++ ADVERTISED_100baseT_Full | ++ ADVERTISED_1000baseT_Half | ++ ADVERTISED_1000baseT_Full); ++ ++ else if (np->current_speed_selection == 100) ++ ecmd->advertising &= ~(ADVERTISED_10baseT_Half | ++ ADVERTISED_10baseT_Full | ++ ADVERTISED_1000baseT_Half | ++ ADVERTISED_1000baseT_Full); ++ ++ else if (np->current_speed_selection == 1000) ++ ecmd->advertising &= ~(ADVERTISED_10baseT_Half | ++ ADVERTISED_10baseT_Full | ++ ADVERTISED_100baseT_Half | ++ ADVERTISED_100baseT_Full); ++ ++ if (np->current_duplex == half) ++ ecmd->advertising &= ~(ADVERTISED_10baseT_Full | ++ ADVERTISED_100baseT_Full | ++ ADVERTISED_1000baseT_Full); ++ else if (np->current_duplex == full) ++ ecmd->advertising &= ~(ADVERTISED_10baseT_Half | ++ ADVERTISED_100baseT_Half | ++ ADVERTISED_1000baseT_Half); ++ } ++ ++ ecmd->autoneg = AUTONEG_ENABLE; ++ return 0; ++} ++ ++static int crisv32_eth_set_settings(struct net_device *dev, ++ struct ethtool_cmd *ecmd) ++{ ++ if (ecmd->autoneg == AUTONEG_ENABLE) { ++ crisv32_eth_set_duplex(dev, autoneg); ++ crisv32_eth_set_speed(dev, 0); ++ } else { ++ crisv32_eth_set_duplex(dev, ecmd->duplex); ++ crisv32_eth_set_speed(dev, ecmd->speed); ++ } ++ ++ return 0; ++} ++ ++static void crisv32_eth_get_drvinfo(struct net_device *dev, ++ struct ethtool_drvinfo *info) ++{ ++ strncpy(info->driver, "ETRAX FS", sizeof(info->driver) - 1); ++ strncpy(info->version, "$Revision: 1.96 $", sizeof(info->version) - 1); ++ strncpy(info->fw_version, "N/A", sizeof(info->fw_version) - 1); ++ strncpy(info->bus_info, "N/A", sizeof(info->bus_info) - 1); ++} ++ ++static int crisv32_eth_nway_reset(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ if (np->current_duplex == autoneg && np->current_speed_selection == 0) ++ crisv32_eth_negotiate(dev); ++ return 0; ++} ++ ++static struct ethtool_ops crisv32_ethtool_ops = { ++ .get_settings = crisv32_eth_get_settings, ++ .set_settings = crisv32_eth_set_settings, ++ .get_drvinfo = crisv32_eth_get_drvinfo, ++ .nway_reset = crisv32_eth_nway_reset, ++ .get_link = ethtool_op_get_link, ++}; ++ ++/* Is this function really needed? Use ethtool instead? */ ++static int ++crisv32_eth_set_config(struct net_device *dev, struct ifmap *map) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->lock); /* Preempt protection */ ++ ++ switch(map->port) { ++ case IF_PORT_UNKNOWN: ++ /* Use autoneg */ ++ crisv32_eth_set_speed(dev, 0); ++ crisv32_eth_set_duplex(dev, autoneg); ++ break; ++ case IF_PORT_10BASET: ++ crisv32_eth_set_speed(dev, 10); ++ crisv32_eth_set_duplex(dev, autoneg); ++ break; ++ case IF_PORT_100BASET: ++ case IF_PORT_100BASETX: ++ crisv32_eth_set_speed(dev, 100); ++ crisv32_eth_set_duplex(dev, autoneg); ++ break; ++ case IF_PORT_100BASEFX: ++ case IF_PORT_10BASE2: ++ case IF_PORT_AUI: ++ spin_unlock(&np->lock); ++ return -EOPNOTSUPP; ++ break; ++ default: ++ printk(KERN_ERR "%s: Invalid media selected", ++ dev->name); ++ spin_unlock(&np->lock); ++ return -EINVAL; ++ } ++ spin_unlock(&np->lock); ++ return 0; ++} ++ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++/* ++ * Switch the behaviour of the tx and rx buffers using ++ * external or internal memory. Usage of the internal ++ * memory is required for gigabit operation. ++ */ ++static void ++crisv32_eth_switch_intmem_usage(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ int i; ++ reg_dma_rw_stat stat; ++ reg_dma_rw_cfg cfg = {0}; ++ reg_dma_rw_intr_mask intr_mask_in = { .in_eop = regk_dma_yes }; ++ reg_dma_rw_ack_intr ack_intr = { .data = 1,.in_eop = 1 }; ++ unsigned char *intmem_tmp; ++ ++ /* Notify the kernel that the interface has stopped */ ++ netif_stop_queue(dev); ++ ++ /* Stop the receiver DMA */ ++ cfg.en = regk_dma_no; ++ REG_WR(dma, np->dma_in_inst, rw_cfg, cfg); ++ ++ if (!(np->gigabit_mode)) { ++ /* deallocate SKBs in rx_desc */ ++ for (i = 0; i < NBR_RX_DESC; i++) ++ dev_kfree_skb(np->dma_rx_descr_list[i].skb); ++ ++ /* Init TX*/ ++ for(i=0; i < NBR_INTMEM_TX_BUF; i++) { ++ /* Allocate internal memory */ ++ intmem_tmp = NULL; ++ intmem_tmp = crisv32_intmem_alloc(MAX_MEDIA_DATA_SIZE, ++ 32); ++ /* Check that we really got the memory */ ++ if (intmem_tmp == NULL) { ++ printk(KERN_ERR "%s: Can't allocate intmem for" ++ " RX buffer nbr: %d\n", dev->name, i); ++ return; ++ } ++ /* Setup the list entry */ ++ np->tx_intmem_buf_list[i].free = 1; ++ np->tx_intmem_buf_list[i].buf = intmem_tmp; ++ np->tx_intmem_buf_list[i].next = &np->tx_intmem_buf_list[i + 1]; ++ } ++ /* Setup the last list entry */ ++ np->tx_intmem_buf_list[NBR_INTMEM_TX_BUF - 1].next = &np->tx_intmem_buf_list[0]; ++ /* Setup initial pointer */ ++ np->intmem_tx_buf_active = np->tx_intmem_buf_list; ++ np->intmem_tx_buf_catch = np->tx_intmem_buf_list; ++ ++ /* Init RX */ ++ for (i=0; i < NBR_INTMEM_RX_DESC; i++) { ++ /* Allocate internal memory */ ++ intmem_tmp = NULL; ++ intmem_tmp = crisv32_intmem_alloc(MAX_MEDIA_DATA_SIZE, 32); ++ /* Check that we really got the memory */ ++ if (intmem_tmp == NULL) { ++ printk(KERN_ERR "%s: Can't allocate intmem for" ++ " desc nbr: %d\n", dev->name, i); ++ return; ++ } ++ /* Setup the descriptors*/ ++ np->dma_rx_descr_list[i].skb = NULL; ++ np->dma_rx_descr_list[i].descr.buf = ++ (void *) crisv32_intmem_virt_to_phys(intmem_tmp); ++ np->dma_rx_descr_list[i].descr.after = ++ (void *) crisv32_intmem_virt_to_phys(intmem_tmp + MAX_MEDIA_DATA_SIZE); ++ np->dma_rx_descr_list[i].descr.eol = 0; ++ np->dma_rx_descr_list[i].descr.in_eop = 0; ++ np->dma_rx_descr_list[i].descr.next = ++ (void *) virt_to_phys(&np->dma_rx_descr_list[i+1].descr); ++ } ++ /* Setup the last rx descriptor */ ++ np->dma_rx_descr_list[NBR_INTMEM_RX_DESC - 1].descr.eol = 1; ++ np->dma_rx_descr_list[NBR_INTMEM_RX_DESC - 1].descr.next = ++ (void*) virt_to_phys(&np->dma_rx_descr_list[0].descr); ++ /* Initialise initial receive pointers. */ ++ np->active_rx_desc = &np->dma_rx_descr_list[0]; ++ np->prev_rx_desc = &np->dma_rx_descr_list[NBR_INTMEM_RX_DESC - 1]; ++ np->last_rx_desc = np->prev_rx_desc; ++ ++ np->gigabit_mode = 1; ++ } else { ++ /* dealloc TX intmem */ ++ for(i=0; i < NBR_INTMEM_TX_BUF; i++) ++ crisv32_intmem_free(np->tx_intmem_buf_list[i].buf); ++ ++ /* dealloc RX intmem */ ++ for (i=0; i < NBR_INTMEM_RX_DESC; i++) ++ crisv32_intmem_free(crisv32_intmem_phys_to_virt((unsigned long)np->dma_rx_descr_list[i].descr.buf)); ++ ++ /* Setup new rx_desc and alloc SKBs */ ++ for (i = 0; i < NBR_RX_DESC; i++) { ++ struct sk_buff *skb; ++ ++ skb = dev_alloc_skb(MAX_MEDIA_DATA_SIZE); ++ np->dma_rx_descr_list[i].skb = skb; ++ np->dma_rx_descr_list[i].descr.buf = ++ (char*)virt_to_phys(skb->data); ++ np->dma_rx_descr_list[i].descr.after = ++ (char*)virt_to_phys(skb->data + MAX_MEDIA_DATA_SIZE); ++ ++ np->dma_rx_descr_list[i].descr.eol = 0; ++ np->dma_rx_descr_list[i].descr.in_eop = 0; ++ np->dma_rx_descr_list[i].descr.next = ++ (void *) virt_to_phys(&np->dma_rx_descr_list[i + 1].descr); ++ } ++ ++ np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.eol = 1; ++ np->dma_rx_descr_list[NBR_RX_DESC - 1].descr.next = ++ (void *) virt_to_phys(&np->dma_rx_descr_list[0].descr); ++ ++ /* Initialise initial receive pointers. */ ++ np->active_rx_desc = &np->dma_rx_descr_list[0]; ++ np->prev_rx_desc = &np->dma_rx_descr_list[NBR_RX_DESC - 1]; ++ np->last_rx_desc = np->prev_rx_desc; ++ ++ np->gigabit_mode = 0; ++ } ++ ++ /* Fill context descriptors. */ ++ np->ctxt_in.next = 0; ++ np->ctxt_in.saved_data = ++ (dma_descr_data *) virt_to_phys(&np->dma_rx_descr_list[0].descr); ++ np->ctxt_in.saved_data_buf = np->dma_rx_descr_list[0].descr.buf; ++ ++ /* Enable irq and make sure that the irqs are cleared. */ ++ REG_WR(dma, np->dma_in_inst, rw_intr_mask, intr_mask_in); ++ REG_WR(dma, np->dma_in_inst, rw_ack_intr, ack_intr); ++ ++ /* Start input dma */ ++ cfg.en = regk_dma_yes; ++ REG_WR(dma, np->dma_in_inst, rw_cfg, cfg); ++ REG_WR(dma, np->dma_in_inst, rw_group_down, ++ (int) virt_to_phys(&np->ctxt_in)); ++ ++ DMA_WR_CMD(np->dma_in_inst, regk_dma_load_c); ++ DMA_WR_CMD(np->dma_in_inst, regk_dma_load_d | regk_dma_burst); ++ ++ netif_wake_queue(dev); ++ ++ stat = REG_RD(dma, np->dma_in_inst, rw_stat); ++} ++#endif ++ ++static void ++crisv32_eth_negotiate(struct net_device *dev) ++{ ++ unsigned short data = ++ crisv32_eth_get_mdio_reg(dev, MII_ADVERTISE); ++ unsigned short ctrl1000 = ++ crisv32_eth_get_mdio_reg(dev, MII_CTRL1000); ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Make all capabilities available */ ++ data |= ADVERTISE_10HALF | ADVERTISE_10FULL | ++ ADVERTISE_100HALF | ADVERTISE_100FULL; ++ ctrl1000 |= ADVERTISE_1000HALF | ADVERTISE_1000FULL; ++ ++ /* Remove the speed capabilities that we that do not want */ ++ switch (np->current_speed_selection) { ++ case 10 : ++ data &= ~(ADVERTISE_100HALF | ADVERTISE_100FULL); ++ ctrl1000 &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL); ++ break; ++ case 100 : ++ data &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL); ++ ctrl1000 &= ~(ADVERTISE_1000HALF | ADVERTISE_1000FULL); ++ break; ++ case 1000 : ++ data &= ~(ADVERTISE_10HALF | ADVERTISE_10FULL | ++ ADVERTISE_100HALF | ADVERTISE_100FULL); ++ break; ++ } ++ ++ /* Remove the duplex capabilites that we do not want */ ++ if (np->current_duplex == full) { ++ data &= ~(ADVERTISE_10HALF | ADVERTISE_100HALF); ++ ctrl1000 &= ~(ADVERTISE_1000HALF); ++ } ++ else if (np->current_duplex == half) { ++ data &= ~(ADVERTISE_10FULL | ADVERTISE_100FULL); ++ ctrl1000 &= ~(ADVERTISE_1000FULL); ++ } ++ ++ crisv32_eth_set_mdio_reg(dev, MII_ADVERTISE, data); ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ crisv32_eth_set_mdio_reg(dev, MII_CTRL1000, ctrl1000); ++#endif ++ ++ /* Renegotiate with link partner */ ++ if (autoneg_normal) { ++ data = crisv32_eth_get_mdio_reg(dev, MII_BMCR); ++ data |= BMCR_ANENABLE | BMCR_ANRESTART; ++ } ++ crisv32_eth_set_mdio_reg(dev, MII_BMCR, data); ++} ++static void ++crisv32_eth_check_speed(unsigned long idev) ++{ ++ static int led_initiated = 0; ++ struct net_device *dev = (struct net_device *) idev; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ unsigned long data; ++ int old_speed; ++ unsigned long flags; ++ ++ BUG_ON(!np); ++ BUG_ON(!np->transceiver); ++ ++ spin_lock(&np->transceiver_lock); ++ ++ old_speed = np->current_speed; ++ data = crisv32_eth_get_mdio_reg(dev, MII_BMSR); ++ ++ if (!(data & BMSR_LSTATUS)) ++ np->current_speed = 0; ++ else ++ np->transceiver->check_speed(dev); ++ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ if ((old_speed != np->current_speed) ++ && ((old_speed == 1000) || (np->current_speed == 1000))) { ++ /* Switch between mii and gmii */ ++ reg_eth_rw_gen_ctrl gen_ctrl = REG_RD(eth, np->eth_inst, ++ rw_gen_ctrl); ++ reg_eth_rw_tr_ctrl tr_ctrl = REG_RD(eth, np->eth_inst, ++ rw_tr_ctrl); ++ if (old_speed == 1000) { ++ gen_ctrl.phy = regk_eth_mii; ++ gen_ctrl.gtxclk_out = regk_eth_no; ++ tr_ctrl.carrier_ext = regk_eth_no; ++ } ++ else { ++ gen_ctrl.phy = regk_eth_gmii; ++ gen_ctrl.gtxclk_out = regk_eth_yes; ++ tr_ctrl.carrier_ext = regk_eth_yes; ++ } ++ REG_WR(eth, np->eth_inst, rw_tr_ctrl, tr_ctrl); ++ REG_WR(eth, np->eth_inst, rw_gen_ctrl, gen_ctrl); ++ ++ crisv32_eth_switch_intmem_usage(dev); ++ } ++#endif ++ ++ spin_lock_irqsave(&np->leds->led_lock, flags); ++ if ((old_speed != np->current_speed) || !led_initiated) { ++ led_initiated = 1; ++ np->leds->clear_led_timer.data = (unsigned long) dev; ++ if (np->current_speed) { ++ netif_carrier_on(dev); ++ crisv32_set_network_leds(LED_LINK, dev); ++ } else { ++ netif_carrier_off(dev); ++ crisv32_set_network_leds(LED_NOLINK, dev); ++ } ++ } ++ spin_unlock_irqrestore(&np->leds->led_lock, flags); ++ ++ /* Reinitialize the timer. */ ++ np->speed_timer.expires = jiffies + NET_LINK_UP_CHECK_INTERVAL; ++ add_timer(&np->speed_timer); ++ ++ spin_unlock(&np->transceiver_lock); ++} ++ ++static void ++crisv32_eth_set_speed(struct net_device *dev, unsigned long speed) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ spin_lock(&np->transceiver_lock); ++ if (np->current_speed_selection != speed) { ++ np->current_speed_selection = speed; ++ crisv32_eth_negotiate(dev); ++ } ++ spin_unlock(&np->transceiver_lock); ++} ++ ++static void ++crisv32_eth_check_duplex(unsigned long idev) ++{ ++ struct net_device *dev = (struct net_device *) idev; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ reg_eth_rw_rec_ctrl rec_ctrl; ++ int old_duplex = np->full_duplex; ++ ++ np->transceiver->check_duplex(dev); ++ ++ if (old_duplex != np->full_duplex) { ++ /* Duplex changed. */ ++ rec_ctrl = (reg_eth_rw_rec_ctrl) REG_RD(eth, np->eth_inst, ++ rw_rec_ctrl); ++ rec_ctrl.duplex = np->full_duplex; ++ REG_WR(eth, np->eth_inst, rw_rec_ctrl, rec_ctrl); ++ } ++ ++ /* Reinitialize the timer. */ ++ np->duplex_timer.expires = jiffies + NET_DUPLEX_CHECK_INTERVAL; ++ add_timer(&np->duplex_timer); ++} ++ ++static void ++crisv32_eth_set_duplex(struct net_device *dev, enum duplex new_duplex) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ spin_lock(&np->transceiver_lock); ++ if (np->current_duplex != new_duplex) { ++ np->current_duplex = new_duplex; ++ crisv32_eth_negotiate(dev); ++ } ++ spin_unlock(&np->transceiver_lock); ++} ++ ++static int ++crisv32_eth_probe_transceiver(struct net_device *dev) ++{ ++ unsigned int phyid_high; ++ unsigned int phyid_low; ++ unsigned int oui; ++ struct transceiver_ops *ops = NULL; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Probe MDIO physical address. */ ++ for (np->mdio_phy_addr = 0; ++ np->mdio_phy_addr <= 31; np->mdio_phy_addr++) { ++ if (crisv32_eth_get_mdio_reg(dev, MII_BMSR) != 0xffff) ++ break; ++ } ++ ++ if (np->mdio_phy_addr == 32) ++ return -ENODEV; ++ ++ /* Get manufacturer. */ ++ phyid_high = crisv32_eth_get_mdio_reg(dev, MII_PHYSID1); ++ phyid_low = crisv32_eth_get_mdio_reg(dev, MII_PHYSID2); ++ ++ oui = (phyid_high << 6) | (phyid_low >> 10); ++ ++ for (ops = &transceivers[0]; ops->oui; ops++) { ++ if (ops->oui == oui) ++ break; ++ } ++ ++ np->transceiver = ops; ++ return 0; ++} ++ ++static void ++generic_check_speed(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MII_ADVERTISE); ++ if ((data & ADVERTISE_100FULL) || ++ (data & ADVERTISE_100HALF)) ++ np->current_speed = 100; ++ else ++ np->current_speed = 10; ++} ++ ++static void ++generic_check_duplex(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MII_ADVERTISE); ++ if ((data & ADVERTISE_10FULL) || ++ (data & ADVERTISE_100FULL)) ++ np->full_duplex = 1; ++ else ++ np->full_duplex = 0; ++} ++ ++static void ++broadcom_check_speed(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_AUX_CTRL_STATUS_REG); ++ np->current_speed = (data & MDIO_BC_SPEED ? 100 : 10); ++} ++ ++static void ++broadcom_check_duplex(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_AUX_CTRL_STATUS_REG); ++ np->full_duplex = (data & MDIO_BC_FULL_DUPLEX_IND) ? 1 : 0; ++} ++ ++static void ++tdk_check_speed(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_TDK_DIAGNOSTIC_REG); ++ np->current_speed = (data & MDIO_TDK_DIAGNOSTIC_RATE ? 100 : 10); ++} ++ ++static void ++tdk_check_duplex(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_TDK_DIAGNOSTIC_REG); ++ np->full_duplex = (data & MDIO_TDK_DIAGNOSTIC_DPLX) ? 1 : 0; ++ ++} ++ ++static void ++intel_check_speed(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_INT_STATUS_REG_2); ++ np->current_speed = (data & MDIO_INT_SPEED ? 100 : 10); ++} ++ ++static void ++intel_check_duplex(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_INT_STATUS_REG_2); ++ np->full_duplex = (data & MDIO_INT_FULL_DUPLEX_IND) ? 1 : 0; ++} ++ ++static void ++national_check_speed(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_NAT_LINK_AN_REG); ++ if (data & MDIO_NAT_1000) ++ np->current_speed = 1000; ++ else if (data & MDIO_NAT_100) ++ np->current_speed = 100; ++ else ++ np->current_speed = 10; ++} ++ ++static void ++national_check_duplex(struct net_device *dev) ++{ ++ unsigned long data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MDIO_NAT_LINK_AN_REG); ++ if (data & MDIO_NAT_FULL_DUPLEX_IND) ++ np->full_duplex = 1; ++ else ++ np->full_duplex = 0; ++} ++ ++static void ++crisv32_eth_reset_tranceiver(struct net_device *dev) ++{ ++ int i; ++ unsigned short cmd; ++ unsigned short data; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ data = crisv32_eth_get_mdio_reg(dev, MII_BMCR); ++ ++ cmd = (MDIO_START << 14) ++ | (MDIO_WRITE << 12) ++ | (np->mdio_phy_addr << 7) ++ | (MII_BMCR << 2); ++ ++ crisv32_eth_send_mdio_cmd(dev, cmd, 1); ++ ++ data |= 0x8000; ++ ++ /* Magic value is number of bits. */ ++ for (i = 15; i >= 0; i--) ++ crisv32_eth_send_mdio_bit(dev, GET_BIT(i, data)); ++} ++ ++static unsigned short ++crisv32_eth_get_mdio_reg(struct net_device *dev, unsigned char reg_num) ++{ ++ int i; ++ unsigned short cmd; /* Data to be sent on MDIO port. */ ++ unsigned short data; /* Data read from MDIO. */ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ /* Start of frame, OP Code, Physical Address, Register Address. */ ++ cmd = (MDIO_START << 14) ++ | (MDIO_READ << 12) ++ | (np->mdio_phy_addr << 7) ++ | (reg_num << 2); ++ ++ crisv32_eth_send_mdio_cmd(dev, cmd, 0); ++ ++ data = 0; ++ ++ /* Receive data. Magic value is number of bits. */ ++ for (i = 15; i >= 0; i--) ++ data |= (crisv32_eth_receive_mdio_bit(dev) << i); ++ ++ return data; ++} ++ ++static void ++crisv32_eth_set_mdio_reg(struct net_device *dev, unsigned char reg, int value) ++{ ++ int bitCounter; ++ unsigned short cmd; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ cmd = (MDIO_START << 14) ++ | (MDIO_WRITE << 12) ++ | (np->mdio_phy_addr << 7) ++ | (reg << 2); ++ ++ crisv32_eth_send_mdio_cmd(dev, cmd, 1); ++ ++ /* Data... */ ++ for (bitCounter=15; bitCounter>=0 ; bitCounter--) { ++ crisv32_eth_send_mdio_bit(dev, GET_BIT(bitCounter, value)); ++ } ++} ++ ++static void ++crisv32_eth_send_mdio_cmd(struct net_device *dev, unsigned short cmd, ++ int write_cmd) ++{ ++ int i; ++ unsigned char data = 0x2; ++ ++ /* Preamble. Magic value is number of bits. */ ++ for (i = 31; i >= 0; i--) ++ crisv32_eth_send_mdio_bit(dev, GET_BIT(i, MDIO_PREAMBLE)); ++ ++ for (i = 15; i >= 2; i--) ++ crisv32_eth_send_mdio_bit(dev, GET_BIT(i, cmd)); ++ ++ /* Turnaround. */ ++ for (i = 1; i >= 0; i--) ++ if (write_cmd) ++ crisv32_eth_send_mdio_bit(dev, GET_BIT(i, data)); ++ else ++ crisv32_eth_receive_mdio_bit(dev); ++} ++ ++static void ++crisv32_eth_send_mdio_bit(struct net_device *dev, unsigned char bit) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ reg_eth_rw_mgm_ctrl mgm_ctrl = { ++ .mdoe = regk_eth_yes, ++ .mdio = bit & 1 ++ }; ++ ++ REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl); ++ ++ udelay(1); ++ ++ mgm_ctrl.mdc = 1; ++ REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl); ++ ++ udelay(1); ++} ++ ++static unsigned char ++crisv32_eth_receive_mdio_bit(struct net_device *dev) ++{ ++ reg_eth_r_stat stat; ++ reg_eth_rw_mgm_ctrl mgm_ctrl = {0}; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ ++ REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl); ++ stat = REG_RD(eth, np->eth_inst, r_stat); ++ ++ udelay(1); ++ ++ mgm_ctrl.mdc = 1; ++ REG_WR(eth, np->eth_inst, rw_mgm_ctrl, mgm_ctrl); ++ ++ udelay(1); ++ return stat.mdio; ++} ++ ++static void ++crisv32_clear_network_leds(unsigned long priv) ++{ ++ struct net_device *dev = (struct net_device*)priv; ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&np->leds->led_lock, flags); ++ if (np->leds->led_active && time_after(jiffies, np->leds->led_next_time)) { ++ crisv32_set_network_leds(LED_NOACTIVITY, dev); ++ ++ /* Set the earliest time we may set the LED */ ++ np->leds->led_next_time = jiffies + NET_FLASH_PAUSE; ++ np->leds->led_active = 0; ++ } ++ spin_unlock_irqrestore(&np->leds->led_lock, flags); ++} ++ ++static void ++crisv32_set_network_leds(int active, struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ int light_leds = 0; ++ ++ if (np->leds->ledgrp == LED_GRP_NONE) ++ return; ++ ++ if (active == LED_NOLINK) { ++ if (dev == crisv32_dev[0]) ++ np->leds->ifisup[0] = 0; ++ else ++ np->leds->ifisup[1] = 0; ++ } ++ else if (active == LED_LINK) { ++ if (dev == crisv32_dev[0]) ++ np->leds->ifisup[0] = 1; ++ else ++ np->leds->ifisup[1] = 1; ++#if defined(CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK) ++ light_leds = 1; ++ } else { ++ light_leds = (active == LED_NOACTIVITY); ++#elif defined(CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY) ++ light_leds = 0; ++ } else { ++ light_leds = (active == LED_ACTIVITY); ++#else ++#error "Define either CONFIG_ETRAX_NETWORK_LED_ON_WHEN_LINK or CONFIG_ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY" ++#endif ++ } ++ ++ if (!use_network_leds) { ++ NET_LED_SET(np->leds->ledgrp,LED_OFF); ++ return; ++ } ++ ++ if (!np->current_speed) { ++ /* Set link down if none of the interfaces that use this led group is up */ ++ if ((np->leds->ifisup[0] + np->leds->ifisup[1]) == 0) { ++#if defined(CONFIG_ETRAX_NETWORK_RED_ON_NO_CONNECTION) ++ /* Make LED red, link is down */ ++ NET_LED_SET(np->leds->ledgrp,LED_RED); ++#else ++ NET_LED_SET(np->leds->ledgrp,LED_OFF); ++#endif ++ } ++ } ++ else if (light_leds) { ++ if (np->current_speed == 10) { ++ NET_LED_SET(np->leds->ledgrp,LED_ORANGE); ++ } else { ++ NET_LED_SET(np->leds->ledgrp,LED_GREEN); ++ } ++ } ++ else { ++ NET_LED_SET(np->leds->ledgrp,LED_OFF); ++ } ++} ++ ++#ifdef CONFIG_NET_POLL_CONTROLLER ++static void ++crisv32_netpoll(struct net_device* netdev) ++{ ++ crisv32rx_eth_interrupt(DMA0_INTR_VECT, netdev, NULL); ++} ++#endif ++ ++#ifdef CONFIG_CPU_FREQ ++static int ++crisv32_ethernet_freq_notifier(struct notifier_block *nb, ++ unsigned long val, void *data) ++{ ++ struct cpufreq_freqs *freqs = data; ++ if (val == CPUFREQ_POSTCHANGE) { ++ int i; ++ for (i = 0; i < 2; i++) { ++ struct net_device* dev = crisv32_dev[i]; ++ unsigned short data; ++ if (dev == NULL) ++ continue; ++ ++ data = crisv32_eth_get_mdio_reg(dev, MII_BMCR); ++ if (freqs->new == 200000) ++ data &= ~BMCR_PDOWN; ++ else ++ data |= BMCR_PDOWN; ++ crisv32_eth_set_mdio_reg(dev, MII_BMCR, data); ++ } ++ } ++ return 0; ++} ++#endif ++ ++/* ++ * Must be called with the np->lock held. ++ */ ++static void crisv32_ethernet_bug(struct net_device *dev) ++{ ++ struct crisv32_ethernet_local *np = netdev_priv(dev); ++ dma_descr_data *dma_pos; ++ dma_descr_data *in_dma_pos; ++ reg_dma_rw_stat stat = {0}; ++ reg_dma_rw_stat in_stat = {0}; ++ int i; ++ ++ /* Get the current output dma position. */ ++ stat = REG_RD(dma, np->dma_out_inst, rw_stat); ++ dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_out_inst, rw_data)); ++ in_stat = REG_RD(dma, np->dma_in_inst, rw_stat); ++ in_dma_pos = phys_to_virt(REG_RD_INT(dma, np->dma_in_inst, rw_data)); ++ ++ printk("%s:\n" ++ "stat.list_state=%x\n" ++ "stat.mode=%x\n" ++ "stat.stream_cmd_src=%x\n" ++ "dma_pos=%x\n" ++ "in_stat.list_state=%x\n" ++ "in_stat.mode=%x\n" ++ "in_stat.stream_cmd_src=%x\n" ++ "in_dma_pos=%x\n" ++ "catch=%x active=%x\n" ++ "packets=%d queue=%d\n" ++ "intr_vect.r_vect=%x\n" ++ "dma.r_masked_intr=%x dma.rw_ack_intr=%x " ++ "dma.r_intr=%x dma.rw_intr_masked=%x\n" ++ "eth.r_stat=%x\n", ++ __func__, ++ stat.list_state, stat.mode, stat.stream_cmd_src, ++ (unsigned int)dma_pos, ++ in_stat.list_state, in_stat.mode, in_stat.stream_cmd_src, ++ (unsigned int)in_dma_pos, ++ (unsigned int)&np->catch_tx_desc->descr, ++ (unsigned int)&np->active_tx_desc->descr, ++ np->txpackets, ++ netif_queue_stopped(dev), ++ REG_RD_INT(intr_vect, regi_irq, r_vect), ++ REG_RD_INT(dma, np->dma_out_inst, r_masked_intr), ++ REG_RD_INT(dma, np->dma_out_inst, rw_ack_intr), ++ REG_RD_INT(dma, np->dma_out_inst, r_intr), ++ REG_RD_INT(dma, np->dma_out_inst, rw_intr_mask), ++ REG_RD_INT(eth, np->eth_inst, r_stat)); ++ ++ printk("tx-descriptors:\n"); ++ for (i = 0; i < NBR_TX_DESC; i++) { ++ printk("txdesc[%d]=0x%x\n", i, (unsigned int) ++ virt_to_phys(&np->dma_tx_descr_list[i].descr)); ++ printk("txdesc[%d].skb=0x%x\n", i, ++ (unsigned int)np->dma_tx_descr_list[i].skb); ++ printk("txdesc[%d].buf=0x%x\n", i, ++ (unsigned int)np->dma_tx_descr_list[i].descr.buf); ++ printk("txdesc[%d].after=0x%x\n", i, ++ (unsigned int)np->dma_tx_descr_list[i].descr.after); ++ printk("txdesc[%d].intr=%x\n", i, ++ np->dma_tx_descr_list[i].descr.intr); ++ printk("txdesc[%d].eol=%x\n", i, ++ np->dma_tx_descr_list[i].descr.eol); ++ printk("txdesc[%d].out_eop=%x\n", i, ++ np->dma_tx_descr_list[i].descr.out_eop); ++ printk("txdesc[%d].wait=%x\n", i, ++ np->dma_tx_descr_list[i].descr.wait); ++ } ++} ++ ++ ++static int ++crisv32_init_module(void) ++{ ++ return crisv32_ethernet_init(); ++} ++ ++module_init(crisv32_init_module); +diff -urN linux-2.6.19.2.orig/drivers/net/cris/eth_v32.h linux-2.6.19.2.dev/drivers/net/cris/eth_v32.h +--- linux-2.6.19.2.orig/drivers/net/cris/eth_v32.h 1970-01-01 01:00:00.000000000 +0100 ++++ linux-2.6.19.2.dev/drivers/net/cris/eth_v32.h 2007-02-06 11:10:37.000000000 +0100 +@@ -0,0 +1,248 @@ ++/* ++ * Definitions for ETRAX FS ethernet driver. ++ * ++ * Copyright (C) 2003, 2004, 2005 Axis Communications. ++ */ ++ ++#ifndef _ETRAX_ETHERNET_H_ ++#define _ETRAX_ETHERNET_H_ ++ ++#include <asm/arch/hwregs/dma.h> ++ ++ ++#define MAX_MEDIA_DATA_SIZE 1522 /* Max packet size. */ ++ ++#define NBR_RX_DESC 64 /* Number of RX descriptors. */ ++#define NBR_TX_DESC 16 /* Number of TX descriptors. */ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++#define NBR_INTMEM_RX_DESC 5 /* Number of RX descriptors in int. mem. ++ * when running in gigabit mode. ++ * Should be less then NBR_RX_DESC ++ */ ++#define NBR_INTMEM_TX_BUF 4 /* Number of TX buffers in int. mem ++ * when running in gigabit mode. ++ * Should be less than NBR_TX_DESC ++ */ ++#endif ++ ++/* Large packets are sent directly to upper layers while small packets ++ * are copied (to reduce memory waste). The following constant ++ * decides the breakpoint. ++ */ ++#define RX_COPYBREAK (256) ++ ++#define ETHER_HEAD_LEN (14) ++ ++/* ++** MDIO constants. ++*/ ++#define MDIO_START 0x1 ++#define MDIO_READ 0x2 ++#define MDIO_WRITE 0x1 ++#define MDIO_PREAMBLE 0xfffffffful ++ ++/* Broadcom specific */ ++#define MDIO_AUX_CTRL_STATUS_REG 0x18 ++#define MDIO_BC_FULL_DUPLEX_IND 0x1 ++#define MDIO_BC_SPEED 0x2 ++ ++/* TDK specific */ ++#define MDIO_TDK_DIAGNOSTIC_REG 18 ++#define MDIO_TDK_DIAGNOSTIC_RATE 0x400 ++#define MDIO_TDK_DIAGNOSTIC_DPLX 0x800 ++ ++/*Intel LXT972A specific*/ ++#define MDIO_INT_STATUS_REG_2 0x0011 ++#define MDIO_INT_FULL_DUPLEX_IND ( 0x0001 << 9 ) ++#define MDIO_INT_SPEED ( 0x0001 << 14 ) ++ ++/*National Semiconductor DP83865 specific*/ ++#define MDIO_NAT_LINK_AN_REG 0x11 ++#define MDIO_NAT_1000 (0x0001 << 4) ++#define MDIO_NAT_100 (0x0001 << 3) ++#define MDIO_NAT_FULL_DUPLEX_IND (0x0001 << 1) ++ ++/* Network flash constants */ ++#define NET_FLASH_TIME (HZ/50) /* 20 ms */ ++#define NET_FLASH_PAUSE (HZ/100) /* 10 ms */ ++#define NET_LINK_UP_CHECK_INTERVAL (2*HZ) /* 2 seconds. */ ++#define NET_DUPLEX_CHECK_INTERVAL (2*HZ) /* 2 seconds. */ ++ ++/* Duplex settings. */ ++enum duplex { ++ half, ++ full, ++ autoneg ++}; ++ ++/* Some transceivers requires special handling. */ ++struct transceiver_ops { ++ unsigned int oui; ++ void (*check_speed) (struct net_device * dev); ++ void (*check_duplex) (struct net_device * dev); ++}; ++ ++typedef struct crisv32_eth_descr { ++ dma_descr_data descr __attribute__ ((__aligned__(32))); ++ struct sk_buff *skb; ++ unsigned char *linearized_packet; ++} crisv32_eth_descr; ++ ++ ++ ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++struct tx_buffer_list { ++ struct tx_buffer_list *next; ++ unsigned char *buf; ++ char free; ++}; ++#endif ++ ++/* LED stuff */ ++#define LED_GRP_0 0 ++#define LED_GRP_1 1 ++#define LED_GRP_NONE 2 ++ ++#define LED_ACTIVITY 0 ++#define LED_NOACTIVITY 1 ++#define LED_LINK 2 ++#define LED_NOLINK 3 ++ ++struct crisv32_eth_leds { ++ unsigned int ledgrp; ++ int led_active; ++ unsigned long led_next_time; ++ struct timer_list clear_led_timer; ++ spinlock_t led_lock; /* Protect LED state */ ++ int ifisup[2]; ++}; ++ ++#define NET_LED_SET(x,y) \ ++ do { \ ++ if (x == 0) LED_NETWORK_GRP0_SET(y); \ ++ if (x == 1) LED_NETWORK_GRP1_SET(y); \ ++ } while (0) ++ ++/* Information that need to be kept for each device. */ ++struct crisv32_ethernet_local { ++ dma_descr_context ctxt_in __attribute__ ((__aligned__(32))); ++ dma_descr_context ctxt_out __attribute__ ((__aligned__(32))); ++ ++ crisv32_eth_descr *active_rx_desc; ++ crisv32_eth_descr *prev_rx_desc; ++ crisv32_eth_descr *last_rx_desc; ++ ++ crisv32_eth_descr *active_tx_desc; ++ crisv32_eth_descr *prev_tx_desc; ++ crisv32_eth_descr *catch_tx_desc; ++ ++ crisv32_eth_descr dma_rx_descr_list[NBR_RX_DESC]; ++ crisv32_eth_descr dma_tx_descr_list[NBR_TX_DESC]; ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++ struct tx_buffer_list tx_intmem_buf_list[NBR_INTMEM_TX_BUF]; ++ struct tx_buffer_list *intmem_tx_buf_active; ++ struct tx_buffer_list *intmem_tx_buf_catch; ++ char gigabit_mode; ++#endif ++ char new_rx_package; ++ ++ /* DMA and ethernet registers for the device. */ ++ int eth_inst; ++ int dma_in_inst; ++ int dma_out_inst; ++ ++ /* Network speed indication. */ ++ struct timer_list speed_timer; ++ int current_speed; /* Speed read from tranceiver */ ++ int current_speed_selection; /* Speed selected by user */ ++ int sender_started; ++ int txpackets; ++ ++ struct crisv32_eth_leds *leds; ++ ++ /* Duplex. */ ++ struct timer_list duplex_timer; ++ int full_duplex; ++ enum duplex current_duplex; ++ ++ struct net_device_stats stats; ++ ++ /* Transciever address. */ ++ unsigned int mdio_phy_addr; ++ ++ struct transceiver_ops *transceiver; ++ ++ /* ++ * TX control lock. This protects the transmit buffer ring state along ++ * with the "tx full" state of the driver. This means all netif_queue ++ * flow control actions are protected by this lock as well. ++ */ ++ spinlock_t lock; ++ spinlock_t transceiver_lock; /* Protect transceiver state. */ ++}; ++ ++/* Function prototypes. */ ++static int crisv32_ethernet_init(void); ++static int crisv32_ethernet_device_init(struct net_device* dev); ++static int crisv32_eth_open(struct net_device *dev); ++static int crisv32_eth_close(struct net_device *dev); ++static int crisv32_eth_set_mac_address(struct net_device *dev, void *vpntr); ++static irqreturn_t crisv32rx_eth_interrupt(int irq, void *dev_id); ++static irqreturn_t crisv32tx_eth_interrupt(int irq, void *dev_id); ++static irqreturn_t crisv32nw_eth_interrupt(int irq, void *dev_id); ++static void crisv32_eth_receive_packet(struct net_device *dev); ++static int crisv32_eth_send_packet(struct sk_buff *skb, struct net_device *dev); ++static void crisv32_eth_hw_send_packet(unsigned char *buf, int length, ++ void *priv); ++static void crisv32_eth_tx_timeout(struct net_device *dev); ++static void crisv32_eth_set_multicast_list(struct net_device *dev); ++static int crisv32_eth_ioctl(struct net_device *dev, struct ifreq *ifr, ++ int cmd); ++static int crisv32_eth_set_config(struct net_device* dev, struct ifmap* map); ++#ifdef CONFIG_CRIS_MACH_ARTPEC3 ++static void crisv32_eth_switch_intmem_usage(struct net_device *dev); ++#endif ++static void crisv32_eth_negotiate(struct net_device *dev); ++static void crisv32_eth_check_speed(unsigned long idev); ++static void crisv32_eth_set_speed(struct net_device *dev, unsigned long speed); ++static void crisv32_eth_check_duplex(unsigned long idev); ++static void crisv32_eth_set_duplex(struct net_device *dev, enum duplex); ++static int crisv32_eth_probe_transceiver(struct net_device *dev); ++ ++static struct ethtool_ops crisv32_ethtool_ops; ++ ++static void generic_check_speed(struct net_device *dev); ++static void generic_check_duplex(struct net_device *dev); ++static void broadcom_check_speed(struct net_device *dev); ++static void broadcom_check_duplex(struct net_device *dev); ++static void tdk_check_speed(struct net_device *dev); ++static void tdk_check_duplex(struct net_device *dev); ++static void intel_check_speed(struct net_device* dev); ++static void intel_check_duplex(struct net_device *dev); ++static void national_check_speed(struct net_device* dev); ++static void national_check_duplex(struct net_device *dev); ++ ++#ifdef CONFIG_NET_POLL_CONTROLLER ++static void crisv32_netpoll(struct net_device* dev); ++#endif ++ ++static void crisv32_clear_network_leds(unsigned long dummy); ++static void crisv32_set_network_leds(int active, struct net_device* dev); ++ ++static void crisv32_eth_reset_tranceiver(struct net_device *dev); ++static unsigned short crisv32_eth_get_mdio_reg(struct net_device *dev, ++ unsigned char reg_num); ++static void crisv32_eth_set_mdio_reg(struct net_device *dev, ++ unsigned char reg_num, ++ int val); ++static void crisv32_eth_send_mdio_cmd(struct net_device *dev, ++ unsigned short cmd, int write_cmd); ++static void crisv32_eth_send_mdio_bit(struct net_device *dev, ++ unsigned char bit); ++static unsigned char crisv32_eth_receive_mdio_bit(struct net_device *dev); ++ ++static struct net_device_stats *crisv32_get_stats(struct net_device *dev); ++static void crisv32_start_dma_out(struct crisv32_ethernet_local* np); ++ ++ ++#endif /* _ETRAX_ETHERNET_H_ */ |