diff options
Diffstat (limited to 'target/linux/ubicom32/files/arch/ubicom32/mach-common/ubi32-gpio.c')
-rw-r--r-- | target/linux/ubicom32/files/arch/ubicom32/mach-common/ubi32-gpio.c | 411 |
1 files changed, 411 insertions, 0 deletions
diff --git a/target/linux/ubicom32/files/arch/ubicom32/mach-common/ubi32-gpio.c b/target/linux/ubicom32/files/arch/ubicom32/mach-common/ubi32-gpio.c new file mode 100644 index 0000000000..5fa22f52b4 --- /dev/null +++ b/target/linux/ubicom32/files/arch/ubicom32/mach-common/ubi32-gpio.c @@ -0,0 +1,411 @@ +/* + * arch/ubicom32/mach-common/ubi32-gpio.c + * Ubicom gpio driver + * + * (C) Copyright 2009, Ubicom, Inc. + * + * This file is part of the Ubicom32 Linux Kernel Port. + * + * The Ubicom32 Linux Kernel Port is free software: you can redistribute + * it and/or modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation, either version 2 of the + * License, or (at your option) any later version. + * + * The Ubicom32 Linux Kernel Port is distributed in the hope that it + * will be useful, but WITHOUT ANY WARRANTY; without even the implied + * warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See + * the GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with the Ubicom32 Linux Kernel Port. If not, + * see <http://www.gnu.org/licenses/>. + * + * Ubicom32 implementation derived from (with many thanks): + * arch/m68knommu + * arch/blackfin + * arch/parisc + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/kernel.h> +#include <linux/io.h> +#include <linux/gpio.h> +#include <linux/irq.h> +#include <linux/version.h> + +#if defined(CONFIG_PROC_FS) +#include <linux/proc_fs.h> +#endif + +#include <linux/io.h> +#include <asm/ip5000.h> +#include <linux/gpio.h> + +#define UBI_GPIO_CHECK_RANGE 0 /* !0 enables range checking */ + + +/* + * Each I/O port can be configured to operate in one of several + * functional modes. One of these modes is GPIO, which causes the + * entire port to function as a GPIO port. Since the various port + * registers serve the system with other important functions, such as + * ethernet, serial, USB, etc., it isn't advantageous to set any of + * the ports to be entirely dedicated for GPIO use. The processor + * alternatively allows individual bits of a port to be assigned to be + * used as GPIO independently from the overall port function. This + * bit-by-bit assignment is selected by setting the corresponding bit + * in the port's gpio_mask register. When set, the selected bit is + * then enabled as a GPIO. If the corresponding bit is set in the + * gpio_ctl register of the port, the bit is configured as a GPIO + * output. Otherwise, it is an input. + * + * NOTE: This driver uses the bit-by-bit GPIO function assignment + * exclusively and *never* sets the port function registers to the + * GPIO function. + * + * GPIO is not the main function of any of the I/O ports. The port + * bit widths are variable from one port to the next, determined by + * the more common I/O functions of the ports. For simplicity, this + * driver assumes all the ports are 32 bits wide regardless of the + * real bit width of the port. GPIO bits are numbered from zero to + * MAX_UBICOM_GPIOS. Within a port, the least significant bit is + * numbered bit zero, the most significant is bit 31. Since the ports + * are considered logically contiguous, GPIO #32 is the zeroth bit in + * port #1, and so on. Due to the hardware definition, there are + * large gaps in the GPIO numbers representing real pins. + * + * NOTE: It is up to the programmer to refer to the processor data + * sheet to determine which bits in which ports can be accessed and + * used for GPIO. + * + */ + + +/* There are 9 ports, A through I. Not all 32 bits in each + * port can be a GPIO, but we pretend they are. Its up to the + * programmer to refer to the processor data sheet. + */ +#define MAX_UBICOM_GPIOS (9 * 32) /* ARCH_NR_GPIOS */ +#define NUM_GPIO_PORTS (gpio_bank(MAX_UBICOM_GPIOS)) + + +/* GPIO reservation bit map array */ +static int reserved_gpio_map[NUM_GPIO_PORTS]; + + +/* Array of hardware io_port addresses */ +static struct ubicom32_io_port *gpio_bank_addr[NUM_GPIO_PORTS] = +{ + UBICOM32_IO_PORT(RA), + UBICOM32_IO_PORT(RB), + UBICOM32_IO_PORT(RC), + UBICOM32_IO_PORT(RD), + UBICOM32_IO_PORT(RE), + UBICOM32_IO_PORT(RF), + UBICOM32_IO_PORT(RG), + UBICOM32_IO_PORT(RH), + UBICOM32_IO_PORT(RI) +}; + + +struct ubi_gpio_chip { + /* + * Right now, nothing else lives here. + */ + struct gpio_chip gpio_chip; +}; + + +#if UBI_GPIO_CHECK_RANGE +inline int check_gpio(unsigned gpio) +{ + if (gpio >= MAX_UBICOM_GPIOS) + return -EINVAL; + return 0; +} +#else +#define check_gpio(n) (0) +#endif + +/* + * ubi_gpio_get_port + * Get the IO port associated with a certain gpio + */ +struct ubicom32_io_port *ubi_gpio_get_port(unsigned gpio) +{ + if (gpio_bank(gpio) > NUM_GPIO_PORTS) { + return NULL; + } + return gpio_bank_addr[gpio_bank(gpio)]; +} + +/* + * ubi_gpio_error() + */ +static void ubi_gpio_error(unsigned gpio) +{ + printk(KERN_ERR "ubicom-gpio: GPIO %d wasn't requested!\n", gpio); +} + +/* + * ubi_port_setup() + */ +static void ubi_port_setup(unsigned gpio, unsigned short usage) +{ + if (!check_gpio(gpio)) { + if (usage) { + UBICOM32_GPIO_ENABLE(gpio); + } else { + UBICOM32_GPIO_DISABLE(gpio); + } + } +} + +/* + * ubi_gpio_request() + */ +static int ubi_gpio_request(struct gpio_chip *chip, unsigned gpio) +{ + unsigned long flags; + + if (check_gpio(gpio) < 0) + return -EINVAL; + + local_irq_save(flags); + + if (unlikely(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))) { + printk(KERN_ERR "ubi-gpio: GPIO %d is already reserved!\n", + gpio); + local_irq_restore(flags); + return -EBUSY; + } + + reserved_gpio_map[gpio_bank(gpio)] |= gpio_bit(gpio); + + ubi_port_setup(gpio, 1); + + local_irq_restore(flags); + + return 0; +} + +/* + * ubi_gpio_free() + */ +static void ubi_gpio_free(struct gpio_chip *chip, unsigned gpio) +{ + unsigned long flags; + + if (check_gpio(gpio) < 0) + return; + + local_irq_save(flags); + + if (unlikely(!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio)))) { + ubi_gpio_error(gpio); + local_irq_restore(flags); + return; + } + + /* Assert the pin is no longer claimed */ + reserved_gpio_map[gpio_bank(gpio)] &= ~gpio_bit(gpio); + + /* Revert port bit to use specified by port->function */ + ubi_port_setup(gpio, 0); + + local_irq_restore(flags); +} + +/* + * ubi_gpio_direction_input() + */ +static int ubi_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) +{ + unsigned long flags; + + if (!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))) { + ubi_gpio_error(gpio); + return -EINVAL; + } + + local_irq_save(flags); + + /* Configure pin as gpio */ + ubi_port_setup(gpio, 1); + + /* Assert pin is an input */ + UBICOM32_GPIO_SET_PIN_INPUT(gpio); + + local_irq_restore(flags); + + return 0; +} + + +/* + * ubi_gpio_direction_output() + */ +static int ubi_gpio_direction_output(struct gpio_chip *chip, + unsigned gpio, int value) +{ + unsigned long flags; + + if (!(reserved_gpio_map[gpio_bank(gpio)] & gpio_bit(gpio))) { + ubi_gpio_error(gpio); + return -EINVAL; + } + + local_irq_save(flags); + + /* Configure pin as gpio and set initial value in gpio_out register + * so that when we enable it as an output, it will have the correct + * initial value. + */ + ubi_port_setup(gpio, 1); + if (value) { + UBICOM32_GPIO_SET_PIN_HIGH(gpio); + } else { + UBICOM32_GPIO_SET_PIN_LOW(gpio); + } + + /* Enable the pin as an output */ + UBICOM32_GPIO_SET_PIN_OUTPUT(gpio); + + local_irq_restore(flags); + + return 0; +} + + +/* + * ubi_gpio_get_value() + */ +static int ubi_gpio_get_value(struct gpio_chip *chip, unsigned gpio) +{ + return 0 != (gpio_bank_addr[gpio_bank(gpio)]->gpio_in & gpio_bit(gpio)); +} + + +/* + * ubi_gpio_set_value() + */ +static void ubi_gpio_set_value(struct gpio_chip *chip, unsigned gpio, + int arg) +{ + unsigned long flags; + local_irq_save(flags); + + if (arg) { + UBICOM32_GPIO_SET_PIN_HIGH(gpio); + } else { + UBICOM32_GPIO_SET_PIN_LOW(gpio); + } + + local_irq_restore(flags); +} + + +/* + * ubi_gpio_to_irq() + */ +static int ubi_gpio_to_irq(struct gpio_chip *chip, unsigned gpio) +{ + return gpio_to_irq(gpio); +} + + +/* + * ubi_gpio_init() + */ +int __init ubi_gpio_init(void) +{ + int k; + int status; + struct ubi_gpio_chip *chip; + struct gpio_chip *gc; + + printk(KERN_INFO "Ubicom GPIO Controller\n"); + + chip = kzalloc(sizeof(struct ubi_gpio_chip), GFP_KERNEL); + if (chip == NULL) + return -ENOMEM; + + gc = &chip->gpio_chip; + gc->request = ubi_gpio_request; + gc->free = ubi_gpio_free; + gc->to_irq = ubi_gpio_to_irq; + gc->direction_input = ubi_gpio_direction_input; + gc->direction_output = ubi_gpio_direction_output; + gc->get = ubi_gpio_get_value; + gc->set = ubi_gpio_set_value; + gc->can_sleep = 0; + gc->base = 0; + gc->ngpio = MAX_UBICOM_GPIOS; /* ARCH_NR_GPIOS - 1 */ + gc->label = "ubi_gpio"; + + status = gpiochip_add(gc); + if (status != 0) { + kfree(chip); + return status; + } + + /* Assert all pins are free */ + for (k = 0; k < NUM_GPIO_PORTS; k++) { + reserved_gpio_map[k] = 0; + } + + return 0; +} + +#if defined(CONFIG_PROC_FS) +/* + * ubi_get_gpio_dir() + */ +static int ubi_get_gpio_dir(unsigned gpio) +{ + if (gpio_bank_addr[gpio_bank(gpio)]->gpio_ctl & gpio_bit(gpio)) + return 1; + else + return 0; +} + +/* + * gpio_proc_read() + */ +static int ubi_gpio_proc_read(char *buf, char **start, off_t offset, + int len, int *unused_i, void *unused_v) +{ + int c, outlen = 0; + + for (c = 0; c < MAX_UBICOM_GPIOS; c++) { + if (!check_gpio(c) && + (reserved_gpio_map[gpio_bank(c)] & gpio_bit(c))) { + len = sprintf(buf, "GPIO_%d:\t\tGPIO %s\n", c, + ubi_get_gpio_dir(c) ? "OUTPUT" : "INPUT"); + } else { + continue; + } + + buf += len; + outlen += len; + } + return outlen; +} + +/* + * ubi_gpio_register_proc() + */ +static __init int ubi_gpio_register_proc(void) +{ + struct proc_dir_entry *proc_gpio; + + proc_gpio = create_proc_entry("gpio", S_IRUGO, NULL); + if (proc_gpio) + proc_gpio->read_proc = ubi_gpio_proc_read; + + return proc_gpio != NULL; +} +device_initcall(ubi_gpio_register_proc); +#endif |