| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In r45970 the MAC swap handling was made opt-in, however some boards
have been forgotten during the conversion. Since the reference design
uses this MAC swapping, and pretty much all known boards using this chip
seem to do so too, enabling the swapping is a more reasonable default
than leaving it disabled.
Change the code to still allow boards to opt-out of this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47956
|
|
|
|
|
|
|
|
|
|
| |
The following patch is to add ath79_register_m25p80_large, which sets
is_flash to false to support bit banging. This is needed on some 32MB+
SPI chips, such as the S25FL256S1
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47952
|
|
|
|
|
|
|
|
|
|
| |
The MR18 stores the ath9k eeprom values on the NAND.
This patch makes it possible to retrieve the images
from there.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47948
|
|
|
|
|
|
|
|
|
| |
move all library includes and 'firmware already exists'
check to the top of the script.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47947
|
|
|
|
|
|
|
|
|
|
|
|
| |
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
|
|
|
|
|
|
|
|
|
|
|
|
| |
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47943
|
|
|
|
|
|
|
|
|
|
|
|
| |
Image generation part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47942
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Image generation (and mtd partition) part of support for
PowerCloud CAP324 Cloud AP. The CAP324 Cloud AP is a device sold by
PowerCloud Systems who's stock firmware (CloudCommand) provides
'cloud' based managment of large numbers of access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via
PoE or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47941
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel part of support for the PowerCloud Systems CR5000. The
CR5000 is a dual-band 802.11n wireless router with 8MB flash,
64 MB RAM, (unused in stock firmware) USB 2.0 port, and five
port gigabit ethernet switch. The CR5000 was sold as hardware for
the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47940
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel part of support for PowerCloud CR3000. The CR3000 is
a 802.11n 2.4 GHz wireless router with 8MB flash, 64MB RAM,
a four port fast ethernet switch, and a fast ethernet wan port which
was sold by PowerCloud Systems as hardware for the Skydog
cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47939
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel part of support for PowerCloud CAP324 Cloud AP.
The CAP324 Cloud AP was a device sold by PowerCloud Systems as hardware for
the CloudCommand service for 'cloud' based managment of large numbers
access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a power adaptor.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47938
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for TRENDnet TEW-823DRU:
- cpu: QCA9558 @720MHz
- flash: 16MB
- ram: 256MB
- 4+1 RJ45 100/1000Mbps
- wifi: QCA9558 (bgn) and QCA9880-BR4A (ac)
- 1x USB 2.0
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 47927
|
|
|
|
|
|
|
|
| |
fixes hangs reported in #18922
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47892
|
|
|
|
|
|
|
|
|
|
| |
Remove reliance on /lib/upgrade/nand.sh as this is called by sysupgrade,
based on felix's comments at
https://lists.openwrt.org/pipermail/openwrt-devel/2015-December/037963.html
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47889
|
|
|
|
|
|
|
|
| |
This patch adds the rx/tx register offsets for the qca955x SoC.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47882
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for Cisco's MR18.
Detailed instructions for the flashing the device can
be found in the OpenWrt forum thread:
<https://forum.openwrt.org/viewtopic.php?id=59248>
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47878
|
|
|
|
|
|
|
|
| |
without adding patch files
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47874
|
|
|
|
|
|
|
|
| |
swapped. use MAC1 for wlan
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47873
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47871
|
|
|
|
|
|
|
|
|
| |
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
|
|
|
|
|
|
|
|
|
|
| |
This patch just extends target/linux/ar71xx/image/Makefile to build
images also for version 2.1 of TL-WR710N
patch against the latest git
Signed off by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47849
|
|
|
|
|
|
|
|
|
| |
The MR18 uses a 3-channel 16-bit PWM Constant Current Driver
for its status LED.
Signed-off-by: Chris R Blake <chrisrblake93@gmail.com>
SVN-Revision: 47848
|
|
|
|
|
|
|
|
| |
This patch is for Wallys DR344 support under OpenWRT
Signed-off-by: Philippe Duchein <wireless-dev@duchein.net>
SVN-Revision: 47847
|
|
|
|
|
|
|
|
| |
Build image for the AP121 reference board with 16MB flash.
Signed-off-by: Norbert Wegener <nw@wegener-net.de>
SVN-Revision: 47846
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47799
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47763
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47753
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47744
|
|
|
|
|
|
|
|
|
| |
Include /lib/functions/system.sh in 02_network to define missing
mtd_get_mac_binary() procedure.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47723
|
|
|
|
|
|
|
|
|
|
| |
This removes calls to ucidef_set_interfaces_lan_wan() and
ucidef_set_interfaces_lan() on boards where all relevant info can be
inferred from the switch definition.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47722
|
|
|
|
|
|
|
|
|
|
|
|
| |
This changes uci-defaults-new.sh, config_generate and all relevant board.d
files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into
a single function.
Also removes now superfluous enable and reset arguments.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47721
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Out of 69 switch definitions, only 3 pass something different than "1" as
values for reset and enable, with one of those three being invalid.
This change ...
* removes the reset and enable arguments from ucidef_add_switch()
* unconditionally writes reset:1 and enable:1 to JSON
* converts the three users of nonstandard values to ucidef_add_switch_attr()
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47720
|
|
|
|
|
|
|
|
|
|
|
| |
- two upstreamed patches removed
- compile tested all targets using 4.1
- run tested ar71xx
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47694
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47672
|
|
|
|
|
|
|
|
|
| |
Also translate ucidef_add_switch_vlan() to ucidef_add_switch_ports() for better
switch topology mapping and improved default config generation.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47663
|
|
|
|
|
|
|
|
| |
The board detect code needs more fixes in order to work properly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47641
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47624
|
|
|
|
|
|
|
|
| |
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47622
|
|
|
|
|
|
|
|
| |
This is the patch for GL-AR300 V3, tested against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47621
|
|
|
|
|
|
|
|
| |
This is the 3rd version. Modified against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47620
|
|
|
|
|
|
| |
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
SVN-Revision: 47612
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47595
|
|
|
|
|
|
|
|
| |
it ends up as $(2) of CatFiles and must be a plain decimal value.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47555
|
|
|
|
|
|
| |
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47554
|
|
|
|
|
|
|
|
|
| |
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47534
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
https://github.com/arduino/openwrt-yun/commit/7e2976fa83fb0d72a955574499178c387a1b3c92
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
|