| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47595
|
|
|
|
|
|
|
|
| |
it ends up as $(2) of CatFiles and must be a plain decimal value.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47555
|
|
|
|
|
|
| |
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47554
|
|
|
|
|
|
|
|
|
| |
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47534
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This is based on patches from Federico Fissore <f.fissore@arduino.cc>
especially this one:
https://github.com/arduino/openwrt-yun/commit/7e2976fa83fb0d72a955574499178c387a1b3c92
The console is running with 250000 baud which is a non standard baud
rate and needs an extra patch to be applied, I will try to get this
patch upstream or something else which accomplish the same.
Some upstream code looks like there are many different versions of this
SoC, are these only internal versions and all versions on the consumer
market are the same? I saw different GPIO configuration and flash sizes
of 8MB and 16MB?
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47451
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 230400 Baud.
With this patch Linux will use the configured baud rate and not some
standard one which is near by.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47450
|
|
|
|
|
|
|
|
|
|
| |
Add access to the function2 gpio register. This probably has to be
converted into a pimux driver later on. This is needed for some setup
functions on the Arduino Yun.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47449
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The international version is completely different from the already
supported Chinese version. The WLAN of the QCA956x SoC used by this router
has been fixed in r46948.
This patch looks like it changes a lot in
700-MIPS-ath79-openwrt-machines.patch; that is not the case. Unfortunately,
quilt decided to completely reorganize the Kconfig patch even though only
a single section has been added.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47420
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47417
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47416
|
|
|
|
|
|
|
|
|
| |
The hardware of the v3 is identical to the v2.
Based-on-patch-by: Andreas Ziegler <github@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47406
|
|
|
|
|
|
| |
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
SVN-Revision: 47405
|
|
|
|
|
|
|
|
|
| |
Some devices require the kernel to be in a JFFS2 file system. Make the
support for this more generic so that it can be used by other devices.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
SVN-Revision: 47404
|
|
|
|
|
|
|
|
|
| |
Incorrect value causes clock inaccuracy as huge as 1/60.
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47363
|
|
|
|
|
|
|
|
|
|
| |
The device is similar to Archer C7 v2, but with 8M of flash, and 6 external
antennas. Reason for breaking the naming pattern is that sticker on the back
mentions "WDR7500" and has no mention of "Archer".
Signed-off-by: Srdjan Rosic <rosic@google.com>
SVN-Revision: 47344
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47333
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47321
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47320
|
|
|
|
|
|
|
|
|
|
|
| |
instead of squashfs-only
All other tplink images use squashfs+jffs2. I don't see any reason why
this board should use squashfs-only
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47319
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47318
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47317
|
|
|
|
| |
SVN-Revision: 47316
|
|
|
|
|
|
| |
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47315
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Observed on ar71xx/ath79 platforms such as Ubiquiti RouterStations.Reported in #20642.:
(https://dev.openwrt.org/ticket/20642).
If embedded command-line text exists with CONFIG_IMAGE_CMDLINE_HACK=y,firmware
init doesn't initialize environment pointer (fw_init_cmdline not called).
arcs_cmdline is not initialized before calling strlcat.
Signed-off-by: Ted Hess <thess@kitschensync.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47270
|
|
|
|
|
|
|
|
|
|
| |
The TL-WR841N/ND v10 is mostly identical to the v9. Apart from some minor
changes, it contains a newer revision of the QCA9533 SoC and the CPU clock
is significantly higher.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47263
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ath9k expects to get revision id 2 for the QCA9531 ver. 2 rev. 0. This
fixes the very low TX power on some devices like the TP-LINK
TL-WR841ND v10.
As ath79_soc_rev is only used to get the revision number to ath9k on the
QCA9533, just set it to the expected value on the ver. 2.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Tested-by: Felix Kaechele <felix@kaechele.ca>
SVN-Revision: 47262
|
|
|
|
|
|
|
|
|
| |
Antminers using the stock bootloader will not hash without this GPIO set.
Applies to DD and CC
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47261
|
|
|
|
|
|
|
|
| |
https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.11
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47252
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes ticket #15267 by enabling power on the
WNR2200's USB port. At present, the USB port on the WNR2200
is non-functional due to it not receiving power.
This patch defines an additional GPIO pin, but none of the
current GPIO definitions have been modified.
Signed-off-by: Riley Baird <BM-2cVqnDuYbAU5do2DfJTrN7ZbAJ246S4XiX@bitmessage.ch>
SVN-Revision: 47236
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch supersedes the v1 from September 17th.
Bumping the patch version - the MiniBox profile showed up under M, but
since it's called 'Gainstrong MiniBox v1.0' now it looks out of place.
Renamed the profile to gs-minibox-v1.mk to fix that.
The following patch adds support for the Gainstrong MiniBox into trunk
(or 'Designated Driver' :D ).
Fixed items:
- Inverted LED polarity (OOLITE seems to suffer from the same problem).
- Changed uppercase MINIBOX_V1_ prefix as requested.
- Prefixes are now gs_minibox_ similar to gs_oolite_ (same vendor).
- Mention the vendor (Gainstrong) in code headers.
Compiles fine, has been confirmed working by owners on 15.05.
Question: I've seen some boards use tools/firmware-utils/src/mktplinkfw.c,
the MiniBox images build fine without, so I'm wondering: do I need to add
it in there as well? Any added benefit?
Thank you
Signed-off by: Stijn Segers <francesco.borromini@inventati.org>
SVN-Revision: 47234
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sets the LEDs to boardname:color:led-name
Sets the LAN to eth0
Other corrections such as the Machine Name and HWIDs
v2 corrects the profile names in the Makefile and changes tabs to spaces
in the Makefile 'define Device/' like the other devices.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 47221
|
|
|
|
|
|
|
|
| |
There are more version on market, add version number to the name.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 47179
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Includes images for
rnx-n360rt
tl-mr3220-v1
tl-mr3420-v1
tl-wa701n-v1
tl-wa730rev1
tl-wa7510n
tl-wa801nd-v1
tl-wa830re-v1
tl-wa901nd-v1
tl-wa901nd-v2
tl-wr740n-v1
tl-wr740n-v3
tl-wr743nd-v1
tl-wr841nd-v3
tl-wr841nd-v5
tl-wr841nd-v7
tl-wr842n-v1
tl-wr941nd-v2
tl-wr941nd-v3
tl-wr941nd-v4
tl-wr1043nd-v1
SVN-Revision: 47178
|
|
|
|
|
|
|
|
| |
all boards has been migrated to the new build step
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47177
|
|
|
|
|
|
|
|
| |
Migrate TLWR1043V2 TLWR2543
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47176
|
|
|
|
|
|
|
|
|
|
| |
* use build step mktplinkfw with extra arguments
* remove now unused mktplinkfw-chn-v2
* use Device/tplink
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47175
|
|
|
|
|
|
|
|
|
| |
Allow to pass extra arguments to mktplinkfw step. Some board requires
an extra argument to create a valid image.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47174
|
|
|
|
|
|
|
|
|
| |
These profiles covered by new image/Makefile descriptions. Only the old format uses
MultiProfile macro
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 47173
|
|
|
|
|
|
|
|
| |
Trivial parch to correct WeIO board name in the system.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
SVN-Revision: 47110
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It seems there are two *different* versions on TL-WR941ND v6: Chinese
and European one. Currently supported by OpenWrt is Chinese one. Rename
firmware to make it clear.
For details see:
http://wiki.openwrt.org/toh/tp-link/tl-wr941nd
https://forum.openwrt.org/viewtopic.php?id=59295
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 47107
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes a regression on spi flash devices (upstream commit 1583eaece6fa).
Changelogs:
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.7
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.8
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.9
* https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.10
096-ipv4-off-by-one-in-continuation-handling-in-proc-net.patch was applied
upstream and dropped.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
[update from 4.1.9 to 4.1.10]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47104
|
|
|
|
|
|
|
|
|
|
| |
Add support for WeIO board (http://we-io.net).
This board is based on Carambola2 board form 8Devices.
Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org> [some cleanups]
SVN-Revision: 47036
|
|
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47034
|
|
|
|
|
|
| |
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46972
|
|
|
|
|
|
|
|
|
|
| |
QCA9563 and QCA9561 are two series of Qualcomm SoC Dragonfly. The only different
is QCA9563 w/o internal switch. It has one GMAC with SGMII interface. But they
have the same device ID(0x1150). So they share the same codes.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46971
|
|
|
|
|
|
| |
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
SVN-Revision: 46970
|
|
|
|
|
|
|
|
| |
This patch adds kernel and userspace support for the Ubiquiti Networks airGateway Pro.
Signed-off-by: Matthew Reeve <mreeve at tenxnetworks.com>
SVN-Revision: 46961
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for TP-LINK TL-WDR3320 v2.
This router uses a chinese version 2 firmware header,.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
SVN-Revision: 46934
|