| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
|
|
|
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41587
|
|
|
|
|
|
|
|
|
|
| |
Move defines and board_info structs back to their proper locations so
(de-)selecting SOC support won't break the build.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41550
|
|
|
|
|
|
|
|
| |
There have been no reported regressions, so backport it to 3.10.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41422
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some fixes for Telsey CPVA502+ bcm6348 routers:
- reset the external PHY (eth1) with proper platform code, not using a led definiton
- eth1 is an external phy, not a switch, deleted forced link speed
- fixed led color
Patch made for 3.14 kernel patches.
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: also fix 3.14, refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41420
|
|
|
|
|
|
|
|
| |
Set usbh ports to 2 to fix #15007.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39681
|
|
|
|
|
|
|
|
| |
Don't only fix up the fallback board, but also all three variants.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39680
|
|
|
|
|
|
|
|
| |
Signed-off-by: Max Staudt <openwrt.max@enpas.org>
Patchwork: http://patchwork.openwrt.org/patch/4729/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39675
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
router.
It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
modem equipped with 64 MiB RAM and 8 MiB flash.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4266/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39671
|
|
|
|
|
|
|
|
|
|
|
|
| |
Update a few devices with their actual port numbers, especially those
with two ports.
Should allow properly using the second port on the Neufboxen and HW553
and HW556.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39325
|
|
|
|
|
|
|
|
|
| |
Changeset r39302 updated a board section and added twice .has_ehci0,
this is not necessary, so fix it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39304
|
|
|
|
|
|
|
|
|
|
| |
BCM6318 has a special initialization sequence which involves touching
PLL control registers in the USBH_PRIV register space, as well as
toggling a bit the Simulation control register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39302
|
|
|
|
|
|
|
|
| |
Power LED is not active low, and ppp-fail is red, not green.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39294
|
|
|
|
|
|
|
|
|
| |
Enable the use of the USB gadget device at the board level so we can use
bcm63xx_udc on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39292
|
|
Add basic support for the BCM96318REF board which is comprised of:
- HS-SPI flash support
- Ethernet switch support
- USB slave device support
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 39283
|