From: Felix Fietkau <nbd@openwrt.org>
Date: Thu, 3 Mar 2016 23:20:06 +0100
Subject: [PATCH] mac80211: minstrel_ht: improve sample rate skip logic

There were a few issues that were slowing down the process of finding
the optimal rate, especially on devices with multi-rate retry
limitations:

When max_tp_rate[0] was slower than max_tp_rate[1], the code did not
sample max_tp_rate[1], which would often allow it to switch places with
max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the
rate is otherwise good).

Also, sample attempts of rates between max_tp_rate[0] and [1] were being
ignored in this case, because the code only checked if the rate was
slower than [1].

Fix this by checking against the fastest / second fastest max_tp_rate
instead of assuming a specific order between the two.

In my tests this patch significantly reduces the time until minstrel_ht
finds the optimal rate right after assoc

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
---

--- a/net/mac80211/rc80211_minstrel_ht.c
+++ b/net/mac80211/rc80211_minstrel_ht.c
@@ -958,6 +958,7 @@ minstrel_get_sample_rate(struct minstrel
 	struct minstrel_rate_stats *mrs;
 	struct minstrel_mcs_group_data *mg;
 	unsigned int sample_dur, sample_group, cur_max_tp_streams;
+	int tp_rate1, tp_rate2;
 	int sample_idx = 0;
 
 	if (mi->sample_wait > 0) {
@@ -979,14 +980,22 @@ minstrel_get_sample_rate(struct minstrel
 	mrs = &mg->rates[sample_idx];
 	sample_idx += sample_group * MCS_GROUP_RATES;
 
+	/* Set tp_rate1, tp_rate2 to the highest / second highest max_tp_rate */
+	if (minstrel_get_duration(mi->max_tp_rate[0]) >
+	    minstrel_get_duration(mi->max_tp_rate[1])) {
+		tp_rate1 = mi->max_tp_rate[1];
+		tp_rate2 = mi->max_tp_rate[0];
+	} else {
+		tp_rate1 = mi->max_tp_rate[0];
+		tp_rate2 = mi->max_tp_rate[1];
+	}
+
 	/*
 	 * Sampling might add some overhead (RTS, no aggregation)
-	 * to the frame. Hence, don't use sampling for the currently
-	 * used rates.
+	 * to the frame. Hence, don't use sampling for the highest currently
+	 * used highest throughput or probability rate.
 	 */
-	if (sample_idx == mi->max_tp_rate[0] ||
-	    sample_idx == mi->max_tp_rate[1] ||
-	    sample_idx == mi->max_prob_rate)
+	if (sample_idx == mi->max_tp_rate[0] || sample_idx == mi->max_prob_rate)
 		return -1;
 
 	/*
@@ -1001,10 +1010,10 @@ minstrel_get_sample_rate(struct minstrel
 	 * if the link is working perfectly.
 	 */
 
-	cur_max_tp_streams = minstrel_mcs_groups[mi->max_tp_rate[0] /
+	cur_max_tp_streams = minstrel_mcs_groups[tp_rate1 /
 		MCS_GROUP_RATES].streams;
 	sample_dur = minstrel_get_duration(sample_idx);
-	if (sample_dur >= minstrel_get_duration(mi->max_tp_rate[1]) &&
+	if (sample_dur >= minstrel_get_duration(tp_rate2) &&
 	    (cur_max_tp_streams - 1 <
 	     minstrel_mcs_groups[sample_group].streams ||
 	     sample_dur >= minstrel_get_duration(mi->max_prob_rate))) {