aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ar71xx/patches-3.10
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: disable usb workarounds for ar913x again (should fix #16610)Felix Fietkau2014-05-251-2/+12
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40846 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: enable usb quirks for all chipidea based devicesFelix Fietkau2014-05-241-14/+19
| | | | | | | | | | | The most important one is qca_force_host_mode, which also sets the 'Stream Disable' bit in the usbmode register. Fixes usb stability issues on AR933x and AR7241/AR7242 Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40841 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx/ath9k: fix reading the WMAC revision on AR953x (fixes #15581)Felix Fietkau2014-05-041-2/+22
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40695 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: allow to configure AR803x PHYs via platform dataGabor Juhos2014-04-131-0/+134
| | | | | | | | | Add a patch for the at803x phy driver, in order to be able to configure some register settings via platform data. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40507 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add phy_mmd_{read,write} helpersGabor Juhos2014-04-131-0/+40
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40506 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: enable console on the RB91x boardsGabor Juhos2014-04-131-2/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40505 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for ZyXEL NBG 6716Gabor Juhos2014-04-131-0/+37
| | | | | | | | | | | | | | | | | | | | | | With this patch OpenWRT supports the following on the ZyXEL NBG 6716: -WiFi 2G (ath9k) -WiFi 5G (ath10k) -NAND flash -2 Ethernet interfaces -USB 2.0 -LEDs including switch -reasonale defaults at first boot Signed-off-by: André Valentin <avalentin@marcant.net> Patchwork: http://patchwork.openwrt.org/patch/5101/ [juhosg: - rename and refresh kernel patch, - fix a few typos, - change button key codes, - use zyxel prefix in LED names] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40499 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: wndr4300: indicate WNDR3700v4 in the kernel support filesGabor Juhos2014-04-121-2/+2
| | | | | | | | | Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300 is the same device. Indicate this in the kernel files. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40479 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: avoid spurious restarts caused by the watchdog on AR934xGabor Juhos2014-04-122-1/+49
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40465 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for the TP-LINK TL-WR841N/ND v9Felix Fietkau2014-04-071-0/+38
| | | | | | | | | | Everything seems to be working fine. Potential issues: * VLAN port IDs are reversed with regard to the numbers on the case. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40400 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for QCA953x SoCFelix Fietkau2014-04-071-0/+406
| | | | | | | | | | | | | | | | | I don't have access to the specs, so I'm not sure about every detail, but I haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty much like a QCA955x without PCI, a little twist in the clock calculation and a AR9331-compatible switch. Features not yet supported: * EHCI (my test system doesn't have USB) * ? (I have no idea if the QCA953x has any other features I don't know about that aren't used by the TL-WR841N v9) Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40399 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.34Gabor Juhos2014-03-271-37/+0
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40291 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the Oolite v1 boardGabor Juhos2014-03-271-0/+39
| | | | | | | | | | | | | | Patch-by: Lars Bøgild Thomsen <lth@cow.dk> Patchwork: http://patchwork.openwrt.org/patch/4922/ [juhosg: - use a separate patch for kernel changes, - reorder Kconfig and Makefile entries, - change function and variable names to be lowercase only and fix misaligned tabs in mach-gs-oolite.c, ... ] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40032 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: rename RB951Ui specific kernel patchGabor Juhos2014-03-271-0/+0
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40031 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.32Gabor Juhos2014-02-232-3/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39707 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: rb91x: add SPI device for the serial shift registerGabor Juhos2014-02-231-1/+1
| | | | | | | | | | | | | The RB91x boards are using a serial shift register connected to the SPI bus to drive some of the LEDs. Rework the board setup code to register a SPI device for that. This makes it possible to use the 'spi-74x164' driver to control the device. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39703 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: improve platform device support in the gpio-74x164 driverGabor Juhos2014-02-231-0/+74
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39701 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add a generic GPIO latch driverGabor Juhos2014-02-221-0/+22
| | | | | | | | It will be used for the Mikrotik boards. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39697 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: spi-ath79: fix initial GPIO CS line setupGabor Juhos2014-02-222-2/+39
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39695 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: refresh unaligned access hacks patchGabor Juhos2014-02-221-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39694 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add support for MikroTik RB951Ui-2HnDGabor Juhos2014-02-201-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | I noticed that the patch at http://patchwork.openwrt.org/patch/4017/ for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been abandoned because it wasn't generated and sent to the mailing list correctly and doesn't apply as a result. I have cleaned up this patch. When testing this on real hardware, I also noticed that wireless didn't work, so this patch fixes that as well. This patch applies cleanly to SVN 39392. Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com> Patchwork: http://patchwork.openwrt.org/patch/4773/ [juhosg: - drop the 'rb951ui_wlan_init' function and rework the code to use the recently introduced rb95x_wlan_init function instead, - fix GPIO number of the port5 LED, - rename LEDs according to the standard LED naming conventions, and use 'rb' prefix in the names] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39641 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the TP-Link TL-WDR4900 v2.0 boardGabor Juhos2014-02-191-0/+23
| | | | | | | | | | | | Patch-by: TenNinjas <tenninjas@tenninjas.ca> Patchwork: http://patchwork.openwrt.org/patch/4848/ [juhosg: - rename and refresh kernel patch, - merge the board setup code into mach-archer-c7.c and drop mach-tl-wdr49000-v2.c] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39635 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix unaligned access hacks for tcp timestampsGabor Juhos2014-02-181-1/+2
| | | | | | | | | | | | This missing bit of the hack saves hugely on instruction traps on tcp connections to ar71xx based routers. Patch-by: Dave Taht <dave.taht@bufferbloat.net> Patchwork: http://patchwork.openwrt.org/patch/4905/ [juhosg: adjust subject, refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39626 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.28Gabor Juhos2014-01-262-5/+5
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39399 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ap83: define mtd layout via command lineGabor Juhos2014-01-231-0/+44
| | | | | | | | | Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39379 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: ap81: define mtd layout via command lineGabor Juhos2014-01-231-0/+49
| | | | | | | | | Also use the RKuImage macro becasue the original firmware starts with the rootfs. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39378 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add a helper function for external LNA GPIO setupGabor Juhos2014-01-102-1/+79
| | | | | | | | | | | | | | The built-in wireless MAC of the AR934x SoC can handle external LNAs and the control signal of the LNAs can be routed to any GPIO line. Add a helper function which can be used to configure the GPIO lines. The helper function will be used for AR934x boards which are using externel LNAs to improve sensitivity. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39215 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add missing tx gain table flag for buffalo wzr-hp-g450hFelix Fietkau2013-12-191-0/+24
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39139 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add initial support for the Mikrotik RB911G/RB912UAG boardsGabor Juhos2013-12-161-0/+39
| | | | | | | | | It is only on RB911G-5HPnD and RB912UAG-5HPnD boards. The LEDs and the USB port is not working yet. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39102 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add NAND driver for the Mikrotik RB91x boardsGabor Juhos2013-12-161-0/+23
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39097 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: rb2011: use board name from the hardware configGabor Juhos2013-12-161-0/+21
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39096 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: refresh m25p80 patchesGabor Juhos2013-12-163-3/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39089 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add dummy rle_decode function if CONFIG_RLE_DECOMPRESS is not setGabor Juhos2013-12-161-1/+11
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39079 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for WD My Net N750Gabor Juhos2013-12-161-0/+39
| | | | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> [juhosg: use a separate patch for kernel changes] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39077 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the TL-WA901ND v3 boardGabor Juhos2013-12-151-0/+10
| | | | | | | | Based-on: http://patchwork.openwrt.org/patch/4506/ Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39073 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the TL-WA801ND v2 boardGabor Juhos2013-12-151-0/+10
| | | | | | | | | | | | | | Patch to add kernel support for the TP-LINK WA801ND v2 Signed-off-by: Jiri Pirko <jiri@resnulli.us> Patchwork: http://patchwork.openwrt.org/patch/4500/ [juhosg: - the TL-WA801ND v2 does not have a sliding switch, it uses a push button for WPS instead. Use the tl_mr3420v2_gpio_keys array to reflect that, - rename kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39063 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel 3.10 to 3.10.24Hauke Mehrtens2013-12-151-1/+1
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39059 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: merge board specific patches into oneLuka Perkov2013-11-3017-539/+165
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38971 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the TL-WR1043ND v2 boardGabor Juhos2013-11-291-0/+39
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38955 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: improve support for the My Net Wi-Fi Range Extender deviceGabor Juhos2013-11-291-1/+2
| | | | | | | | | | | | | | | | | | | | This patch improves support for the device considerably. 1. The wifi didn't work in the initial release. This was because the WMAC of the AR9340 is not connected to the antennas. (However, it can pick up wifi signals, if they are strong enough!) Instead there's a dedicated AR9300 chip on the same board, which works. 2. Ethernet throughput is improved. iperf shows that the hardware can sustain more than 200Mbit/s and no longer drops any packages when the link is under load. Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Patchwork: http://patchwork.openwrt.org/patch/4461/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38949 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ag71xx: add F1E specific feature bit definitions to AR934X register fileGabor Juhos2013-11-291-1/+3
| | | | | | | | | | | | | | | | The F1E Phy (AR8035?) requires additional bits to be set in order to provide a fast and reliable connection over gigabit links. When enabled, the link doesn't suffer anymore from a small package loss under load and the performance is improved quite a bit as well. (203 mbit/s vs 112 mbit/s, iperf tcp). Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Patchwork: http://patchwork.openwrt.org/patch/4460/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38948 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add kernel support for the WR842N/ND v2Gabor Juhos2013-11-151-0/+10
| | | | | | | | | | | Patch to add kernel support for the TP-LINK WR842N/ND v2 Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com> Patchwork: http://patchwork.openwrt.org/patch/4352/ [juhosg: refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38813 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add kernel support for the TP-Link WA750RE / WA850RE range extenderGabor Juhos2013-11-111-0/+40
| | | | | | | | | | | Patch to add kernel support for the TP-LINK WA750RE and the WA850RE range extender Signed-off-by: Martijn Zilverschoon <thefriedzombie@gmail.com> [juhosg: rename and refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38717 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the My Net Wi-Fi Range Extender deviceGabor Juhos2013-11-071-0/+39
| | | | | | | | | | | | | This patch adds a new device definition for a Western Digital device. The hardware seems to be based on Qualcomm Atheros DB120 design. Patchwork: http://patchwork.openwrt.org/patch/4281/ Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> [juhosg: refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38686 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.18Gabor Juhos2013-11-051-4/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38652 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix Kconfig symbol selection for RB95x/RB2011Gabor Juhos2013-10-309-14/+17
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38596 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for BHU Networks BXU2000n-2 A1 boardGabor Juhos2013-10-301-0/+39
| | | | | | | | | | | | | | BXU2000n-2 A1 is a BHU Networks WLAN board, use ar9341 chip. Patchwork: http://patchwork.openwrt.org/patch/4183/ Signed-off-by: Terry Yang <yangbo@bhunetworks.com> [juhosg: - rename and refresh kernel patch, - fix some checkpatch warnings and adjust whitespaces in mach-bhu-bxu2000n2-a.c] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38591 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for the Sitecom WLR-8100 wireless routerGabor Juhos2013-10-301-0/+39
| | | | | | | | | | | | - unsure about copyright message - based on AP136-010 Patchwork: http://patchwork.openwrt.org/patch/4147/ Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> [juhosg: rename and refresh kernel patch] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38589 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add kernel support for DRAGINO2Gabor Juhos2013-10-301-0/+39
| | | | | | | | | | | | | | | | | | | This patch adds support for DRAGINO2 board (used by Meshpotato v2). Most of the files included can be found in the official svn repository provided by the company [1]. I have just adapt it to the last OpenWrt trunk revision (Fri Oct 4 10:49:47 2013). 1. http://svn.dragino.com/dragino2 Patchwork: http://patchwork.openwrt.org/patch/4234/ Signed-off-by: Pau Escrich <p4u@dabax.net> [juhosg: - rename and refresh kernel patch, - fix checkpatch warnings in mach-dragino2.c] Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38587 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.17Gabor Juhos2013-10-231-8/+11
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38506 3c298f89-4303-0410-b956-a3cf2f4a3e73