aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq
Commit message (Collapse)AuthorAgeFilesLines
* lntiq: add support for Astoria ARV7519RW.John Crispin2014-03-306-0/+319
| | | | | | | | | | | | | | | These patches add support for the Astoria ARV7519RW aka Livebox 2.1 The PCI and PCIe interfaces have been disabled. Also, because there are two revisions of this board with different GPHY firmwares, two targets were defined. V2: rewrote partitions to work with an u-boot specifically made for these boards. Signed off by: Esteban Benito <estebanjbs@gmail.com> Signed off by: Carles Gadea <carlesgrg@gmail.com> Tested by: José Vázquez Fernández <ppvazquezfer@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40329 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: do an endianness swap to the RT2860 eeprom for ARV752DPW(22)John Crispin2014-03-301-4/+13
| | | | | | | | | | | | | | | | | | | | ARV7510PW22, ARV752DPW and ARV752DPW22 have the RT2860 eeprom stored in flash as big-endian, but the driver needs it in little-endian format. We have to swab it before handing it over. This requires my earlier patch for busybox. Funnily enough, ARV752DPW works also with the incorrect eeprom, but undoubtedly unoptimally. I have a hunch that also the final remaining Lantiq board would require this swabbing, but I'm not sure, so I just swab it in the three boards that I know about. v2: * Swab also on ARV7510PW22 based on feedback from Alvaro Rojas * Fix the offset with bs=2 Signed-off-by: Matti Laakso <malaakso at elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40328 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add esiJohn Crispin2014-03-302-1/+8
| | | | | | | | http://patchwork.openwrt.org/patch/3703/ Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40326 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix mtd_split for brnboot firmware imagesJohn Crispin2014-03-301-1/+1
| | | | | | | | | | | | | | | | | | | | The existing code only tries to split a parition with name "rootfs" while actually looking for kernel+rootfs, where usually "firmware" is used as a partition name. This doesn't make sense, as even if there was a partition 'rootfs' given by mtdparts or via device-tree, this code would lead to another partition called 'rootfs' being created which would not be properly distinguished in the current user-space code. While potentially we could use CONFIG_MTD_SPLIT_FIRMWARE_NAME to make that configurable, the lack of users of brnboot and the fact that we can freely decide the partition name made me simply change the hard-coded string constant from "rootfs" to "firmware". (I'm going to add support for ARV7506PW which run brnboot and needs this change) git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40324 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fixup ath5k supportJohn Crispin2014-03-301-0/+55
| | | | | | | | http://patchwork.openwrt.org/patch/4417/ Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40323 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix initial VLAN conf for P2601HNFXJohn Crispin2014-03-301-2/+3
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40321 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: P2601HNFX dts update for STP and buttonsJohn Crispin2014-03-301-3/+6
| | | | | | | | | - Set correct AltSel for STP pins - Set front button to rfkill Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40320 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add support for Arcadyan ARV7519PWJohn Crispin2014-03-305-1/+238
| | | | | | | | | | | This patch adds almost full support for this board. - WiFi is still not working - USB will not power up. According to some reports, it may be a passive port Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40319 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: reset gphys on rebootJohn Crispin2014-03-301-0/+19
| | | | | | | | If gphys are not reset upstream uboot can not use them anymore. Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40318 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add support for ZyXEL P2812HNUFXJohn Crispin2014-03-304-0/+332
| | | | | | | | | | | This patch adds almost full support for this board. WiFi is still not working. The FXS ports are not functional due to missing support for the TAPI driver on VR9 SoC. Signed-off-by: Antonios Vamporakis <ant@area128.com> Tested-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40317 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add ubifs support in image MakefileJohn Crispin2014-03-301-0/+43
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40316 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add ubifs to FEATURESJohn Crispin2014-03-302-2/+2
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40315 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: xrx200: add ubi support in the kernelJohn Crispin2014-03-301-0/+17
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40314 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add inital support for xrx200 switchJohn Crispin2014-03-301-0/+2023
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40313 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: xrx200: fix duplexJohn Crispin2014-03-301-0/+13
| | | | | | | | | | Both the GPL driver from ZyXEL and the xrx200 driver have this error. The flags are reversed. Full duplex is marked as half and the other way around. With this fix the switch will push full GBit speeds. Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40312 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fixup 3370 dts fileJohn Crispin2014-03-301-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40311 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix nand/ebu lockingJohn Crispin2014-03-301-0/+21
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40310 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add tffs driverJohn Crispin2014-03-301-0/+110
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40309 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: drop old svip foldersJohn Crispin2014-03-278-145/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40294 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.34Gabor Juhos2014-03-271-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40291 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.32Gabor Juhos2014-02-234-9/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39707 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix typo in pinctl driverLuka Perkov2014-02-151-0/+32
| | | | | | Signed-off-by: Antonios Vamporakis <ant@area128.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39588 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix PCI problems on ARV4510PWLuka Perkov2014-02-151-1/+5
| | | | | | | | | Some ARV4510PW units seem to have unstable PCI due to missing pull-up resistors. This patch makes sure that the GPIO lines are driven properly. Signed-off-by: Matti Laakso <malaakso@elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39587 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.28Gabor Juhos2014-01-262-2/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39399 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: Add support for Astoria ARV7510PW22John Crispin2014-01-155-2/+198
| | | | | | | | This board is pretty similar to ARV752DPW22. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39303 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: update kernel configurationLuka Perkov2014-01-153-3/+1
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39296 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: improve Arcadyan ARV4510PW supportJohn Crispin2014-01-123-37/+135
| | | | | | | | | Arcadyan ARV4510PW has already a build profile in OpenWrt, but it is severely lacking. This patch brings it up-to-date. Signed-off-by: Matti Laakso <malaakso@elisanet.fi> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39230 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.26Gabor Juhos2014-01-112-3/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39220 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel 3.10 to 3.10.24Hauke Mehrtens2013-12-151-1/+1
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39059 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.21Gabor Juhos2013-12-012-2/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38972 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: move patch to proper folderJohn Crispin2013-11-201-0/+121
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38884 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: update default mii modesJohn Crispin2013-11-202-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38881 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix an endless loop in the vmmc platform codeJohn Crispin2013-11-201-1/+1
| | | | | | | | this was caused by not honoured error return codes of of_gpio_count() Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38878 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: DGN3500 fixupsJohn Crispin2013-11-112-1/+3
| | | | | | | | Just fixing up a few things for the Netgear DGN3500. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38733 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: rename TDW8970 led adsl->dslJohn Crispin2013-11-111-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38730 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: update TDW8970.dts to support buttons properlyJohn Crispin2013-11-111-2/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38728 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: remove old hotplug handlerJohn Crispin2013-11-111-53/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38727 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix TDW8970 lan/wan macJohn Crispin2013-11-071-1/+9
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38677 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: Fix ar8216 switch configuration for WBMR-HP-G300H devicesJohn Crispin2013-11-071-2/+3
| | | | | | | | | | | The switch is renamed to "switch0" in newer (3.10) linux kernels. Configure the switch using vlans by default and only configure the physical switch ports that are present. Signed-off-by: Richard Mortimer <richm@oldelvet.org.uk> Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38673 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix td-w8970 initramfs generationJohn Crispin2013-11-071-3/+2
| | | | | | | | https://dev.openwrt.org/ticket/14417 Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38667 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.18Gabor Juhos2013-11-052-4/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38652 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 3.10 to 3.10.17Gabor Juhos2013-10-232-21/+13
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38506 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel to 3.10.15Hauke Mehrtens2013-10-131-1/+1
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38384 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix up diag.shJohn Crispin2013-10-081-2/+0
| | | | | | | | init no longer exists as a parameter Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38342 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: experia v8 fixesJohn Crispin2013-10-073-4/+4
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38328 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix fritz3370 dts fileJohn Crispin2013-10-071-55/+50
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38327 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix fritz image generationJohn Crispin2013-10-072-8/+10
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38326 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix eva partition split for squashfsJohn Crispin2013-10-071-49/+35
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38325 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add support for VGV7519 KPN Experia box v8John Crispin2013-09-305-0/+399
| | | | | | | Signed-off-by: Maikel Bloemendal <mbloemendal@gmail.com> Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38266 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: add a default for CONFIG_MTD_NAND_XWAY to fix build errorsFelix Fietkau2013-09-271-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@38243 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 21:35:47 +0000