From c90d6b25d5aaadf371db8452b82f1700853cd22a Mon Sep 17 00:00:00 2001 From: John Crispin Date: Sun, 4 Aug 2013 13:54:32 +0000 Subject: octeon: add support for the octeon mips64 SoC This is the SoC used be the ESR Lite made by ubnt.com Signed-off-by: John Crispin git-svn-id: svn://svn.openwrt.org/openwrt/trunk@37684 3c298f89-4303-0410-b956-a3cf2f4a3e73 --- .../drivers/staging/octeon-usb/cvmx-usbnx-defs.h | 887 +++++++++++++++++++++ 1 file changed, 887 insertions(+) create mode 100644 target/linux/octeon/files/drivers/staging/octeon-usb/cvmx-usbnx-defs.h (limited to 'target/linux/octeon/files/drivers/staging/octeon-usb/cvmx-usbnx-defs.h') diff --git a/target/linux/octeon/files/drivers/staging/octeon-usb/cvmx-usbnx-defs.h b/target/linux/octeon/files/drivers/staging/octeon-usb/cvmx-usbnx-defs.h new file mode 100644 index 0000000000..96d706770f --- /dev/null +++ b/target/linux/octeon/files/drivers/staging/octeon-usb/cvmx-usbnx-defs.h @@ -0,0 +1,887 @@ +/***********************license start*************** + * Copyright (c) 2003-2010 Cavium Networks (support@cavium.com). All rights + * reserved. + * + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are + * met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above + * copyright notice, this list of conditions and the following + * disclaimer in the documentation and/or other materials provided + * with the distribution. + + * * Neither the name of Cavium Networks nor the names of + * its contributors may be used to endorse or promote products + * derived from this software without specific prior written + * permission. + + * This Software, including technical data, may be subject to U.S. export + * control laws, including the U.S. Export Administration Act and its associated + * regulations, and may be subject to export or import regulations in other + * countries. + + * TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS" + * AND WITH ALL FAULTS AND CAVIUM NETWORKS MAKES NO PROMISES, REPRESENTATIONS OR + * WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT TO + * THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY REPRESENTATION + * OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT DEFECTS, AND CAVIUM + * SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES OF TITLE, + * MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR PURPOSE, LACK OF + * VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, QUIET POSSESSION OR + * CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK ARISING OUT OF USE OR + * PERFORMANCE OF THE SOFTWARE LIES WITH YOU. + ***********************license end**************************************/ + + +/** + * cvmx-usbnx-defs.h + * + * Configuration and status register (CSR) type definitions for + * Octeon usbnx. + * + */ +#ifndef __CVMX_USBNX_TYPEDEFS_H__ +#define __CVMX_USBNX_TYPEDEFS_H__ + +#define CVMX_USBNXBID1(bid) (((bid) & 1) * 0x10000000ull) +#define CVMX_USBNXBID2(bid) (((bid) & 1) * 0x100000000000ull) + +#define CVMX_USBNXREG1(reg, bid) \ + (CVMX_ADD_IO_SEG(0x0001180068000000ull | reg) + CVMX_USBNXBID1(bid)) +#define CVMX_USBNXREG2(reg, bid) \ + (CVMX_ADD_IO_SEG(0x00016F0000000000ull | reg) + CVMX_USBNXBID2(bid)) + +#define CVMX_USBNX_CLK_CTL(bid) CVMX_USBNXREG1(0x10, bid) +#define CVMX_USBNX_DMA0_INB_CHN0(bid) CVMX_USBNXREG2(0x818, bid) +#define CVMX_USBNX_DMA0_OUTB_CHN0(bid) CVMX_USBNXREG2(0x858, bid) +#define CVMX_USBNX_USBP_CTL_STATUS(bid) CVMX_USBNXREG1(0x18, bid) + +/** + * cvmx_usbn#_clk_ctl + * + * USBN_CLK_CTL = USBN's Clock Control + * + * This register is used to control the frequency of the hclk and the + * hreset and phy_rst signals. + */ +union cvmx_usbnx_clk_ctl { + uint64_t u64; + /** + * struct cvmx_usbnx_clk_ctl_s + * @divide2: The 'hclk' used by the USB subsystem is derived + * from the eclk. + * Also see the field DIVIDE. DIVIDE2<1> must currently + * be zero because it is not implemented, so the maximum + * ratio of eclk/hclk is currently 16. + * The actual divide number for hclk is: + * (DIVIDE2 + 1) * (DIVIDE + 1) + * @hclk_rst: When this field is '0' the HCLK-DIVIDER used to + * generate the hclk in the USB Subsystem is held + * in reset. This bit must be set to '0' before + * changing the value os DIVIDE in this register. + * The reset to the HCLK_DIVIDERis also asserted + * when core reset is asserted. + * @p_x_on: Force USB-PHY on during suspend. + * '1' USB-PHY XO block is powered-down during + * suspend. + * '0' USB-PHY XO block is powered-up during + * suspend. + * The value of this field must be set while POR is + * active. + * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to + * remain powered in Suspend Mode. + * '1' The USB-PHY XO Bias, Bandgap and PLL are + * powered down in suspend mode. + * The value of this field must be set while POR is + * active. + * @p_c_sel: Phy clock speed select. + * Selects the reference clock / crystal frequency. + * '11': Reserved + * '10': 48 MHz (reserved when a crystal is used) + * '01': 24 MHz (reserved when a crystal is used) + * '00': 12 MHz + * The value of this field must be set while POR is + * active. + * NOTE: if a crystal is used as a reference clock, + * this field must be set to 12 MHz. + * @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV. + * @sd_mode: Scaledown mode for the USBC. Control timing events + * in the USBC, for normal operation this must be '0'. + * @s_bist: Starts bist on the hclk memories, during the '0' + * to '1' transition. + * @por: Power On Reset for the PHY. + * Resets all the PHYS registers and state machines. + * @enable: When '1' allows the generation of the hclk. When + * '0' the hclk will not be generated. SEE DIVIDE + * field of this register. + * @prst: When this field is '0' the reset associated with + * the phy_clk functionality in the USB Subsystem is + * help in reset. This bit should not be set to '1' + * until the time it takes 6 clocks (hclk or phy_clk, + * whichever is slower) has passed. Under normal + * operation once this bit is set to '1' it should not + * be set to '0'. + * @hrst: When this field is '0' the reset associated with + * the hclk functioanlity in the USB Subsystem is + * held in reset.This bit should not be set to '1' + * until 12ms after phy_clk is stable. Under normal + * operation, once this bit is set to '1' it should + * not be set to '0'. + * @divide: The frequency of 'hclk' used by the USB subsystem + * is the eclk frequency divided by the value of + * (DIVIDE2 + 1) * (DIVIDE + 1), also see the field + * DIVIDE2 of this register. + * The hclk frequency should be less than 125Mhz. + * After writing a value to this field the SW should + * read the field for the value written. + * The ENABLE field of this register should not be set + * until AFTER this field is set and then read. + */ + struct cvmx_usbnx_clk_ctl_s { + uint64_t reserved_20_63 : 44; + uint64_t divide2 : 2; + uint64_t hclk_rst : 1; + uint64_t p_x_on : 1; + uint64_t reserved_14_15 : 2; + uint64_t p_com_on : 1; + uint64_t p_c_sel : 2; + uint64_t cdiv_byp : 1; + uint64_t sd_mode : 2; + uint64_t s_bist : 1; + uint64_t por : 1; + uint64_t enable : 1; + uint64_t prst : 1; + uint64_t hrst : 1; + uint64_t divide : 3; + } s; + /** + * struct cvmx_usbnx_clk_ctl_cn30xx + * @hclk_rst: When this field is '0' the HCLK-DIVIDER used to + * generate the hclk in the USB Subsystem is held + * in reset. This bit must be set to '0' before + * changing the value os DIVIDE in this register. + * The reset to the HCLK_DIVIDERis also asserted + * when core reset is asserted. + * @p_x_on: Force USB-PHY on during suspend. + * '1' USB-PHY XO block is powered-down during + * suspend. + * '0' USB-PHY XO block is powered-up during + * suspend. + * The value of this field must be set while POR is + * active. + * @p_rclk: Phy refrence clock enable. + * '1' The PHY PLL uses the XO block output as a + * reference. + * '0' Reserved. + * @p_xenbn: Phy external clock enable. + * '1' The XO block uses the clock from a crystal. + * '0' The XO block uses an external clock supplied + * on the XO pin. USB_XI should be tied to + * ground for this usage. + * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to + * remain powered in Suspend Mode. + * '1' The USB-PHY XO Bias, Bandgap and PLL are + * powered down in suspend mode. + * The value of this field must be set while POR is + * active. + * @p_c_sel: Phy clock speed select. + * Selects the reference clock / crystal frequency. + * '11': Reserved + * '10': 48 MHz + * '01': 24 MHz + * '00': 12 MHz + * The value of this field must be set while POR is + * active. + * @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV. + * @sd_mode: Scaledown mode for the USBC. Control timing events + * in the USBC, for normal operation this must be '0'. + * @s_bist: Starts bist on the hclk memories, during the '0' + * to '1' transition. + * @por: Power On Reset for the PHY. + * Resets all the PHYS registers and state machines. + * @enable: When '1' allows the generation of the hclk. When + * '0' the hclk will not be generated. + * @prst: When this field is '0' the reset associated with + * the phy_clk functionality in the USB Subsystem is + * help in reset. This bit should not be set to '1' + * until the time it takes 6 clocks (hclk or phy_clk, + * whichever is slower) has passed. Under normal + * operation once this bit is set to '1' it should not + * be set to '0'. + * @hrst: When this field is '0' the reset associated with + * the hclk functioanlity in the USB Subsystem is + * held in reset.This bit should not be set to '1' + * until 12ms after phy_clk is stable. Under normal + * operation, once this bit is set to '1' it should + * not be set to '0'. + * @divide: The 'hclk' used by the USB subsystem is derived + * from the eclk. The eclk will be divided by the + * value of this field +1 to determine the hclk + * frequency. (Also see HRST of this register). + * The hclk frequency must be less than 125 MHz. + */ + struct cvmx_usbnx_clk_ctl_cn30xx { + uint64_t reserved_18_63 : 46; + uint64_t hclk_rst : 1; + uint64_t p_x_on : 1; + uint64_t p_rclk : 1; + uint64_t p_xenbn : 1; + uint64_t p_com_on : 1; + uint64_t p_c_sel : 2; + uint64_t cdiv_byp : 1; + uint64_t sd_mode : 2; + uint64_t s_bist : 1; + uint64_t por : 1; + uint64_t enable : 1; + uint64_t prst : 1; + uint64_t hrst : 1; + uint64_t divide : 3; + } cn30xx; + struct cvmx_usbnx_clk_ctl_cn30xx cn31xx; + /** + * struct cvmx_usbnx_clk_ctl_cn50xx + * @divide2: The 'hclk' used by the USB subsystem is derived + * from the eclk. + * Also see the field DIVIDE. DIVIDE2<1> must currently + * be zero because it is not implemented, so the maximum + * ratio of eclk/hclk is currently 16. + * The actual divide number for hclk is: + * (DIVIDE2 + 1) * (DIVIDE + 1) + * @hclk_rst: When this field is '0' the HCLK-DIVIDER used to + * generate the hclk in the USB Subsystem is held + * in reset. This bit must be set to '0' before + * changing the value os DIVIDE in this register. + * The reset to the HCLK_DIVIDERis also asserted + * when core reset is asserted. + * @p_rtype: PHY reference clock type + * '0' The USB-PHY uses a 12MHz crystal as a clock + * source at the USB_XO and USB_XI pins + * '1' Reserved + * '2' The USB_PHY uses 12/24/48MHz 2.5V board clock + * at the USB_XO pin. USB_XI should be tied to + * ground in this case. + * '3' Reserved + * (bit 14 was P_XENBN on 3xxx) + * (bit 15 was P_RCLK on 3xxx) + * @p_com_on: '0' Force USB-PHY XO Bias, Bandgap and PLL to + * remain powered in Suspend Mode. + * '1' The USB-PHY XO Bias, Bandgap and PLL are + * powered down in suspend mode. + * The value of this field must be set while POR is + * active. + * @p_c_sel: Phy clock speed select. + * Selects the reference clock / crystal frequency. + * '11': Reserved + * '10': 48 MHz (reserved when a crystal is used) + * '01': 24 MHz (reserved when a crystal is used) + * '00': 12 MHz + * The value of this field must be set while POR is + * active. + * NOTE: if a crystal is used as a reference clock, + * this field must be set to 12 MHz. + * @cdiv_byp: Used to enable the bypass input to the USB_CLK_DIV. + * @sd_mode: Scaledown mode for the USBC. Control timing events + * in the USBC, for normal operation this must be '0'. + * @s_bist: Starts bist on the hclk memories, during the '0' + * to '1' transition. + * @por: Power On Reset for the PHY. + * Resets all the PHYS registers and state machines. + * @enable: When '1' allows the generation of the hclk. When + * '0' the hclk will not be generated. SEE DIVIDE + * field of this register. + * @prst: When this field is '0' the reset associated with + * the phy_clk functionality in the USB Subsystem is + * help in reset. This bit should not be set to '1' + * until the time it takes 6 clocks (hclk or phy_clk, + * whichever is slower) has passed. Under normal + * operation once this bit is set to '1' it should not + * be set to '0'. + * @hrst: When this field is '0' the reset associated with + * the hclk functioanlity in the USB Subsystem is + * held in reset.This bit should not be set to '1' + * until 12ms after phy_clk is stable. Under normal + * operation, once this bit is set to '1' it should + * not be set to '0'. + * @divide: The frequency of 'hclk' used by the USB subsystem + * is the eclk frequency divided by the value of + * (DIVIDE2 + 1) * (DIVIDE + 1), also see the field + * DIVIDE2 of this register. + * The hclk frequency should be less than 125Mhz. + * After writing a value to this field the SW should + * read the field for the value written. + * The ENABLE field of this register should not be set + * until AFTER this field is set and then read. + */ + struct cvmx_usbnx_clk_ctl_cn50xx { + uint64_t reserved_20_63 : 44; + uint64_t divide2 : 2; + uint64_t hclk_rst : 1; + uint64_t reserved_16_16 : 1; + uint64_t p_rtype : 2; + uint64_t p_com_on : 1; + uint64_t p_c_sel : 2; + uint64_t cdiv_byp : 1; + uint64_t sd_mode : 2; + uint64_t s_bist : 1; + uint64_t por : 1; + uint64_t enable : 1; + uint64_t prst : 1; + uint64_t hrst : 1; + uint64_t divide : 3; + } cn50xx; + struct cvmx_usbnx_clk_ctl_cn50xx cn52xx; + struct cvmx_usbnx_clk_ctl_cn50xx cn56xx; +}; +typedef union cvmx_usbnx_clk_ctl cvmx_usbnx_clk_ctl_t; + +/** + * cvmx_usbn#_usbp_ctl_status + * + * USBN_USBP_CTL_STATUS = USBP Control And Status Register + * + * Contains general control and status information for the USBN block. + */ +union cvmx_usbnx_usbp_ctl_status { + uint64_t u64; + /** + * struct cvmx_usbnx_usbp_ctl_status_s + * @txrisetune: HS Transmitter Rise/Fall Time Adjustment + * @txvreftune: HS DC Voltage Level Adjustment + * @txfslstune: FS/LS Source Impedence Adjustment + * @txhsxvtune: Transmitter High-Speed Crossover Adjustment + * @sqrxtune: Squelch Threshold Adjustment + * @compdistune: Disconnect Threshold Adjustment + * @otgtune: VBUS Valid Threshold Adjustment + * @otgdisable: OTG Block Disable + * @portreset: Per_Port Reset + * @drvvbus: Drive VBUS + * @lsbist: Low-Speed BIST Enable. + * @fsbist: Full-Speed BIST Enable. + * @hsbist: High-Speed BIST Enable. + * @bist_done: PHY Bist Done. + * Asserted at the end of the PHY BIST sequence. + * @bist_err: PHY Bist Error. + * Indicates an internal error was detected during + * the BIST sequence. + * @tdata_out: PHY Test Data Out. + * Presents either internaly generated signals or + * test register contents, based upon the value of + * test_data_out_sel. + * @siddq: Drives the USBP (USB-PHY) SIDDQ input. + * Normally should be set to zero. + * When customers have no intent to use USB PHY + * interface, they should: + * - still provide 3.3V to USB_VDD33, and + * - tie USB_REXT to 3.3V supply, and + * - set USBN*_USBP_CTL_STATUS[SIDDQ]=1 + * @txpreemphasistune: HS Transmitter Pre-Emphasis Enable + * @dma_bmode: When set to 1 the L2C DMA address will be updated + * with byte-counts between packets. When set to 0 + * the L2C DMA address is incremented to the next + * 4-byte aligned address after adding byte-count. + * @usbc_end: Bigendian input to the USB Core. This should be + * set to '0' for operation. + * @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP. + * @tclk: PHY Test Clock, used to load TDATA_IN to the USBP. + * @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D+ line. '1' pull down-resistance is connected + * to D+/ '0' pull down resistance is not connected + * to D+. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D- line. '1' pull down-resistance is connected + * to D-. '0' pull down resistance is not connected + * to D-. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @hst_mode: When '0' the USB is acting as HOST, when '1' + * USB is acting as device. This field needs to be + * set while the USB is in reset. + * @tuning: Transmitter Tuning for High-Speed Operation. + * Tunes the current supply and rise/fall output + * times for high-speed operation. + * [20:19] == 11: Current supply increased + * approximately 9% + * [20:19] == 10: Current supply increased + * approximately 4.5% + * [20:19] == 01: Design default. + * [20:19] == 00: Current supply decreased + * approximately 4.5% + * [22:21] == 11: Rise and fall times are increased. + * [22:21] == 10: Design default. + * [22:21] == 01: Rise and fall times are decreased. + * [22:21] == 00: Rise and fall times are decreased + * further as compared to the 01 setting. + * @tx_bs_enh: Transmit Bit Stuffing on [15:8]. + * Enables or disables bit stuffing on data[15:8] + * when bit-stuffing is enabled. + * @tx_bs_en: Transmit Bit Stuffing on [7:0]. + * Enables or disables bit stuffing on data[7:0] + * when bit-stuffing is enabled. + * @loop_enb: PHY Loopback Test Enable. + * '1': During data transmission the receive is + * enabled. + * '0': During data transmission the receive is + * disabled. + * Must be '0' for normal operation. + * @vtest_enb: Analog Test Pin Enable. + * '1' The PHY's analog_test pin is enabled for the + * input and output of applicable analog test signals. + * '0' THe analog_test pin is disabled. + * @bist_enb: Built-In Self Test Enable. + * Used to activate BIST in the PHY. + * @tdata_sel: Test Data Out Select. + * '1' test_data_out[3:0] (PHY) register contents + * are output. '0' internaly generated signals are + * output. + * @taddr_in: Mode Address for Test Interface. + * Specifies the register address for writing to or + * reading from the PHY test interface register. + * @tdata_in: Internal Testing Register Input Data and Select + * This is a test bus. Data is present on [3:0], + * and its corresponding select (enable) is present + * on bits [7:4]. + * @ate_reset: Reset input from automatic test equipment. + * This is a test signal. When the USB Core is + * powered up (not in Susned Mode), an automatic + * tester can use this to disable phy_clock and + * free_clk, then re-eanable them with an aligned + * phase. + * '1': The phy_clk and free_clk outputs are + * disabled. "0": The phy_clock and free_clk outputs + * are available within a specific period after the + * de-assertion. + */ + struct cvmx_usbnx_usbp_ctl_status_s { + uint64_t txrisetune : 1; + uint64_t txvreftune : 4; + uint64_t txfslstune : 4; + uint64_t txhsxvtune : 2; + uint64_t sqrxtune : 3; + uint64_t compdistune : 3; + uint64_t otgtune : 3; + uint64_t otgdisable : 1; + uint64_t portreset : 1; + uint64_t drvvbus : 1; + uint64_t lsbist : 1; + uint64_t fsbist : 1; + uint64_t hsbist : 1; + uint64_t bist_done : 1; + uint64_t bist_err : 1; + uint64_t tdata_out : 4; + uint64_t siddq : 1; + uint64_t txpreemphasistune : 1; + uint64_t dma_bmode : 1; + uint64_t usbc_end : 1; + uint64_t usbp_bist : 1; + uint64_t tclk : 1; + uint64_t dp_pulld : 1; + uint64_t dm_pulld : 1; + uint64_t hst_mode : 1; + uint64_t tuning : 4; + uint64_t tx_bs_enh : 1; + uint64_t tx_bs_en : 1; + uint64_t loop_enb : 1; + uint64_t vtest_enb : 1; + uint64_t bist_enb : 1; + uint64_t tdata_sel : 1; + uint64_t taddr_in : 4; + uint64_t tdata_in : 8; + uint64_t ate_reset : 1; + } s; + /** + * struct cvmx_usbnx_usbp_ctl_status_cn30xx + * @bist_done: PHY Bist Done. + * Asserted at the end of the PHY BIST sequence. + * @bist_err: PHY Bist Error. + * Indicates an internal error was detected during + * the BIST sequence. + * @tdata_out: PHY Test Data Out. + * Presents either internaly generated signals or + * test register contents, based upon the value of + * test_data_out_sel. + * @dma_bmode: When set to 1 the L2C DMA address will be updated + * with byte-counts between packets. When set to 0 + * the L2C DMA address is incremented to the next + * 4-byte aligned address after adding byte-count. + * @usbc_end: Bigendian input to the USB Core. This should be + * set to '0' for operation. + * @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP. + * @tclk: PHY Test Clock, used to load TDATA_IN to the USBP. + * @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D+ line. '1' pull down-resistance is connected + * to D+/ '0' pull down resistance is not connected + * to D+. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D- line. '1' pull down-resistance is connected + * to D-. '0' pull down resistance is not connected + * to D-. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @hst_mode: When '0' the USB is acting as HOST, when '1' + * USB is acting as device. This field needs to be + * set while the USB is in reset. + * @tuning: Transmitter Tuning for High-Speed Operation. + * Tunes the current supply and rise/fall output + * times for high-speed operation. + * [20:19] == 11: Current supply increased + * approximately 9% + * [20:19] == 10: Current supply increased + * approximately 4.5% + * [20:19] == 01: Design default. + * [20:19] == 00: Current supply decreased + * approximately 4.5% + * [22:21] == 11: Rise and fall times are increased. + * [22:21] == 10: Design default. + * [22:21] == 01: Rise and fall times are decreased. + * [22:21] == 00: Rise and fall times are decreased + * further as compared to the 01 setting. + * @tx_bs_enh: Transmit Bit Stuffing on [15:8]. + * Enables or disables bit stuffing on data[15:8] + * when bit-stuffing is enabled. + * @tx_bs_en: Transmit Bit Stuffing on [7:0]. + * Enables or disables bit stuffing on data[7:0] + * when bit-stuffing is enabled. + * @loop_enb: PHY Loopback Test Enable. + * '1': During data transmission the receive is + * enabled. + * '0': During data transmission the receive is + * disabled. + * Must be '0' for normal operation. + * @vtest_enb: Analog Test Pin Enable. + * '1' The PHY's analog_test pin is enabled for the + * input and output of applicable analog test signals. + * '0' THe analog_test pin is disabled. + * @bist_enb: Built-In Self Test Enable. + * Used to activate BIST in the PHY. + * @tdata_sel: Test Data Out Select. + * '1' test_data_out[3:0] (PHY) register contents + * are output. '0' internaly generated signals are + * output. + * @taddr_in: Mode Address for Test Interface. + * Specifies the register address for writing to or + * reading from the PHY test interface register. + * @tdata_in: Internal Testing Register Input Data and Select + * This is a test bus. Data is present on [3:0], + * and its corresponding select (enable) is present + * on bits [7:4]. + * @ate_reset: Reset input from automatic test equipment. + * This is a test signal. When the USB Core is + * powered up (not in Susned Mode), an automatic + * tester can use this to disable phy_clock and + * free_clk, then re-eanable them with an aligned + * phase. + * '1': The phy_clk and free_clk outputs are + * disabled. "0": The phy_clock and free_clk outputs + * are available within a specific period after the + * de-assertion. + */ + struct cvmx_usbnx_usbp_ctl_status_cn30xx { + uint64_t reserved_38_63 : 26; + uint64_t bist_done : 1; + uint64_t bist_err : 1; + uint64_t tdata_out : 4; + uint64_t reserved_30_31 : 2; + uint64_t dma_bmode : 1; + uint64_t usbc_end : 1; + uint64_t usbp_bist : 1; + uint64_t tclk : 1; + uint64_t dp_pulld : 1; + uint64_t dm_pulld : 1; + uint64_t hst_mode : 1; + uint64_t tuning : 4; + uint64_t tx_bs_enh : 1; + uint64_t tx_bs_en : 1; + uint64_t loop_enb : 1; + uint64_t vtest_enb : 1; + uint64_t bist_enb : 1; + uint64_t tdata_sel : 1; + uint64_t taddr_in : 4; + uint64_t tdata_in : 8; + uint64_t ate_reset : 1; + } cn30xx; + /** + * struct cvmx_usbnx_usbp_ctl_status_cn50xx + * @txrisetune: HS Transmitter Rise/Fall Time Adjustment + * @txvreftune: HS DC Voltage Level Adjustment + * @txfslstune: FS/LS Source Impedence Adjustment + * @txhsxvtune: Transmitter High-Speed Crossover Adjustment + * @sqrxtune: Squelch Threshold Adjustment + * @compdistune: Disconnect Threshold Adjustment + * @otgtune: VBUS Valid Threshold Adjustment + * @otgdisable: OTG Block Disable + * @portreset: Per_Port Reset + * @drvvbus: Drive VBUS + * @lsbist: Low-Speed BIST Enable. + * @fsbist: Full-Speed BIST Enable. + * @hsbist: High-Speed BIST Enable. + * @bist_done: PHY Bist Done. + * Asserted at the end of the PHY BIST sequence. + * @bist_err: PHY Bist Error. + * Indicates an internal error was detected during + * the BIST sequence. + * @tdata_out: PHY Test Data Out. + * Presents either internaly generated signals or + * test register contents, based upon the value of + * test_data_out_sel. + * @txpreemphasistune: HS Transmitter Pre-Emphasis Enable + * @dma_bmode: When set to 1 the L2C DMA address will be updated + * with byte-counts between packets. When set to 0 + * the L2C DMA address is incremented to the next + * 4-byte aligned address after adding byte-count. + * @usbc_end: Bigendian input to the USB Core. This should be + * set to '0' for operation. + * @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP. + * @tclk: PHY Test Clock, used to load TDATA_IN to the USBP. + * @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D+ line. '1' pull down-resistance is connected + * to D+/ '0' pull down resistance is not connected + * to D+. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D- line. '1' pull down-resistance is connected + * to D-. '0' pull down resistance is not connected + * to D-. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @hst_mode: When '0' the USB is acting as HOST, when '1' + * USB is acting as device. This field needs to be + * set while the USB is in reset. + * @tx_bs_enh: Transmit Bit Stuffing on [15:8]. + * Enables or disables bit stuffing on data[15:8] + * when bit-stuffing is enabled. + * @tx_bs_en: Transmit Bit Stuffing on [7:0]. + * Enables or disables bit stuffing on data[7:0] + * when bit-stuffing is enabled. + * @loop_enb: PHY Loopback Test Enable. + * '1': During data transmission the receive is + * enabled. + * '0': During data transmission the receive is + * disabled. + * Must be '0' for normal operation. + * @vtest_enb: Analog Test Pin Enable. + * '1' The PHY's analog_test pin is enabled for the + * input and output of applicable analog test signals. + * '0' THe analog_test pin is disabled. + * @bist_enb: Built-In Self Test Enable. + * Used to activate BIST in the PHY. + * @tdata_sel: Test Data Out Select. + * '1' test_data_out[3:0] (PHY) register contents + * are output. '0' internaly generated signals are + * output. + * @taddr_in: Mode Address for Test Interface. + * Specifies the register address for writing to or + * reading from the PHY test interface register. + * @tdata_in: Internal Testing Register Input Data and Select + * This is a test bus. Data is present on [3:0], + * and its corresponding select (enable) is present + * on bits [7:4]. + * @ate_reset: Reset input from automatic test equipment. + * This is a test signal. When the USB Core is + * powered up (not in Susned Mode), an automatic + * tester can use this to disable phy_clock and + * free_clk, then re-eanable them with an aligned + * phase. + * '1': The phy_clk and free_clk outputs are + * disabled. "0": The phy_clock and free_clk outputs + * are available within a specific period after the + * de-assertion. + */ + struct cvmx_usbnx_usbp_ctl_status_cn50xx { + uint64_t txrisetune : 1; + uint64_t txvreftune : 4; + uint64_t txfslstune : 4; + uint64_t txhsxvtune : 2; + uint64_t sqrxtune : 3; + uint64_t compdistune : 3; + uint64_t otgtune : 3; + uint64_t otgdisable : 1; + uint64_t portreset : 1; + uint64_t drvvbus : 1; + uint64_t lsbist : 1; + uint64_t fsbist : 1; + uint64_t hsbist : 1; + uint64_t bist_done : 1; + uint64_t bist_err : 1; + uint64_t tdata_out : 4; + uint64_t reserved_31_31 : 1; + uint64_t txpreemphasistune : 1; + uint64_t dma_bmode : 1; + uint64_t usbc_end : 1; + uint64_t usbp_bist : 1; + uint64_t tclk : 1; + uint64_t dp_pulld : 1; + uint64_t dm_pulld : 1; + uint64_t hst_mode : 1; + uint64_t reserved_19_22 : 4; + uint64_t tx_bs_enh : 1; + uint64_t tx_bs_en : 1; + uint64_t loop_enb : 1; + uint64_t vtest_enb : 1; + uint64_t bist_enb : 1; + uint64_t tdata_sel : 1; + uint64_t taddr_in : 4; + uint64_t tdata_in : 8; + uint64_t ate_reset : 1; + } cn50xx; + /** + * struct cvmx_usbnx_usbp_ctl_status_cn52xx + * @txrisetune: HS Transmitter Rise/Fall Time Adjustment + * @txvreftune: HS DC Voltage Level Adjustment + * @txfslstune: FS/LS Source Impedence Adjustment + * @txhsxvtune: Transmitter High-Speed Crossover Adjustment + * @sqrxtune: Squelch Threshold Adjustment + * @compdistune: Disconnect Threshold Adjustment + * @otgtune: VBUS Valid Threshold Adjustment + * @otgdisable: OTG Block Disable + * @portreset: Per_Port Reset + * @drvvbus: Drive VBUS + * @lsbist: Low-Speed BIST Enable. + * @fsbist: Full-Speed BIST Enable. + * @hsbist: High-Speed BIST Enable. + * @bist_done: PHY Bist Done. + * Asserted at the end of the PHY BIST sequence. + * @bist_err: PHY Bist Error. + * Indicates an internal error was detected during + * the BIST sequence. + * @tdata_out: PHY Test Data Out. + * Presents either internaly generated signals or + * test register contents, based upon the value of + * test_data_out_sel. + * @siddq: Drives the USBP (USB-PHY) SIDDQ input. + * Normally should be set to zero. + * When customers have no intent to use USB PHY + * interface, they should: + * - still provide 3.3V to USB_VDD33, and + * - tie USB_REXT to 3.3V supply, and + * - set USBN*_USBP_CTL_STATUS[SIDDQ]=1 + * @txpreemphasistune: HS Transmitter Pre-Emphasis Enable + * @dma_bmode: When set to 1 the L2C DMA address will be updated + * with byte-counts between packets. When set to 0 + * the L2C DMA address is incremented to the next + * 4-byte aligned address after adding byte-count. + * @usbc_end: Bigendian input to the USB Core. This should be + * set to '0' for operation. + * @usbp_bist: PHY, This is cleared '0' to run BIST on the USBP. + * @tclk: PHY Test Clock, used to load TDATA_IN to the USBP. + * @dp_pulld: PHY DP_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D+ line. '1' pull down-resistance is connected + * to D+/ '0' pull down resistance is not connected + * to D+. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @dm_pulld: PHY DM_PULLDOWN input to the USB-PHY. + * This signal enables the pull-down resistance on + * the D- line. '1' pull down-resistance is connected + * to D-. '0' pull down resistance is not connected + * to D-. When an A/B device is acting as a host + * (downstream-facing port), dp_pulldown and + * dm_pulldown are enabled. This must not toggle + * during normal opeartion. + * @hst_mode: When '0' the USB is acting as HOST, when '1' + * USB is acting as device. This field needs to be + * set while the USB is in reset. + * @tx_bs_enh: Transmit Bit Stuffing on [15:8]. + * Enables or disables bit stuffing on data[15:8] + * when bit-stuffing is enabled. + * @tx_bs_en: Transmit Bit Stuffing on [7:0]. + * Enables or disables bit stuffing on data[7:0] + * when bit-stuffing is enabled. + * @loop_enb: PHY Loopback Test Enable. + * '1': During data transmission the receive is + * enabled. + * '0': During data transmission the receive is + * disabled. + * Must be '0' for normal operation. + * @vtest_enb: Analog Test Pin Enable. + * '1' The PHY's analog_test pin is enabled for the + * input and output of applicable analog test signals. + * '0' THe analog_test pin is disabled. + * @bist_enb: Built-In Self Test Enable. + * Used to activate BIST in the PHY. + * @tdata_sel: Test Data Out Select. + * '1' test_data_out[3:0] (PHY) register contents + * are output. '0' internaly generated signals are + * output. + * @taddr_in: Mode Address for Test Interface. + * Specifies the register address for writing to or + * reading from the PHY test interface register. + * @tdata_in: Internal Testing Register Input Data and Select + * This is a test bus. Data is present on [3:0], + * and its corresponding select (enable) is present + * on bits [7:4]. + * @ate_reset: Reset input from automatic test equipment. + * This is a test signal. When the USB Core is + * powered up (not in Susned Mode), an automatic + * tester can use this to disable phy_clock and + * free_clk, then re-eanable them with an aligned + * phase. + * '1': The phy_clk and free_clk outputs are + * disabled. "0": The phy_clock and free_clk outputs + * are available within a specific period after the + * de-assertion. + */ + struct cvmx_usbnx_usbp_ctl_status_cn52xx { + uint64_t txrisetune : 1; + uint64_t txvreftune : 4; + uint64_t txfslstune : 4; + uint64_t txhsxvtune : 2; + uint64_t sqrxtune : 3; + uint64_t compdistune : 3; + uint64_t otgtune : 3; + uint64_t otgdisable : 1; + uint64_t portreset : 1; + uint64_t drvvbus : 1; + uint64_t lsbist : 1; + uint64_t fsbist : 1; + uint64_t hsbist : 1; + uint64_t bist_done : 1; + uint64_t bist_err : 1; + uint64_t tdata_out : 4; + uint64_t siddq : 1; + uint64_t txpreemphasistune : 1; + uint64_t dma_bmode : 1; + uint64_t usbc_end : 1; + uint64_t usbp_bist : 1; + uint64_t tclk : 1; + uint64_t dp_pulld : 1; + uint64_t dm_pulld : 1; + uint64_t hst_mode : 1; + uint64_t reserved_19_22 : 4; + uint64_t tx_bs_enh : 1; + uint64_t tx_bs_en : 1; + uint64_t loop_enb : 1; + uint64_t vtest_enb : 1; + uint64_t bist_enb : 1; + uint64_t tdata_sel : 1; + uint64_t taddr_in : 4; + uint64_t tdata_in : 8; + uint64_t ate_reset : 1; + } cn52xx; +}; +typedef union cvmx_usbnx_usbp_ctl_status cvmx_usbnx_usbp_ctl_status_t; + +#endif -- cgit v1.2.3