brcm63xx: update development kernel to linux 3.14

Now that 3.13 will be EOL soon, switch to 3.14.

Known issues:
 * 74x164 is not available because upstream dropped non-DT support
 * jffs2 breaks with SMP

Unknown issues:
 * probably plenty

Signed-off-by: Jonas Gorski <jogo@openwrt.org>

git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40380 3c298f89-4303-0410-b956-a3cf2f4a3e73

1 files changed, 145 insertions, 0 deletions

diff --git a/target/linux/brcm63xx/patches-3.14/536-board_fast2704.patch b/target/linux/brcm63xx/patches-3.14/536-board_fast2704.patch
new file mode 100644
index 0000000000..c08135c947
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.14/536-board_fast2704.patch
@@ -0,0 +1,145 @@
+From: Marcin Jurkowski <marcin1j@gmail.com>
+Date: Thu, 31 Oct 2013 22:33:10 +0000
+Subject: [PATCH] bcm63xx: Add kernel support for Sagemcom F@ST2704V2 ADSL
+ router
+
+This adds kernel support support for Sagemcom F@st 2704 wireless ADSL
+router.
+It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+
+modem equipped with 64 MiB RAM and 8 MiB flash.
+
+Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
+---
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -1482,6 +1482,122 @@ static struct board_info __initdata boar
+ 	},
+ };
+ 
++static struct board_info __initdata board_FAST2704V2 = {
++	.name				= "F@ST2704V2",
++	.expected_cpu_id		= 0x6328,
++
++	.has_uart0			= 1,
++	.has_pci			= 1,
++	.has_ohci0			= 1,
++	.has_ehci0			= 1,
++	.has_usbd			= 1,
++
++	.has_enetsw			= 1,
++
++	.enetsw = {
++		.used_ports = {
++			[0] = {
++				.used	= 1,
++				.phy_id = 1,
++				.name	= "Port 1",
++			},
++			[1] = {
++				.used	= 1,
++				.phy_id	= 2,
++				.name	= "Port 2",
++			},
++			[2] = {
++				.used	= 1,
++				.phy_id	= 3,
++				.name	= "Port 3",
++			},
++			[3] = {
++				.used	= 1,
++				.phy_id	= 4,
++				.name	= "Port 4",
++			},
++		},
++	},
++
++	.leds = {
++		/* front LEDs */
++		{
++			.name			= "F@ST2704V2:green:power",
++			.gpio			= 4,
++			.active_low		= 1,
++			.default_trigger	= "default-on",
++		},
++		{
++			.name			= "F@ST2704V2:red:power",
++			.gpio			= 5,
++			.active_low		= 1,
++		},
++		{
++			.name			= "F@ST2704V2:red:inet",
++			.gpio			= 2,
++			.active_low		= 1,
++		},
++		{
++			.name			= "F@ST2704V2:green:dsl",
++			.gpio			= 3,
++			.active_low		= 1,
++		},
++		{
++			.name			= "F@ST2704V2:green:inet",
++			.gpio			= 11,
++			.active_low		= 1,
++		},
++		{
++			.name			= "F@ST2704V2:green:usb",
++			.gpio			= 1,
++			.active_low		= 1,
++		},
++
++		/* side button LEDs */
++		{
++			.name			= "F@ST2704V2:green:wps",
++			.gpio			= 10,
++			.active_low		= 1,
++		},
++
++		/* FIXME: can't control gpio0 line in "out" state, needs further investigation */
++		/*
++		{
++			.name			= "F@ST2704V2:green:rfkill",
++			.gpio			= 0,
++			.active_low		= 1,
++		},
++		*/
++
++	},
++	.buttons = {
++		{
++			.desc			= "reset",
++			.gpio			= 23,
++			.active_low		= 1,
++			.type			= EV_KEY,
++			.code			= KEY_RESTART,
++			.debounce_interval	= BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc			= "wps",
++			.gpio			= 24,
++			.active_low		= 1,
++			.type			= EV_KEY,
++			.code			= KEY_WPS_BUTTON,
++			.debounce_interval	= BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++		{
++			.desc			= "rfkill",
++			.gpio			= 15,
++			.active_low		= 1,
++			.type			= EV_KEY,
++			.code			= KEY_WLAN,
++			.debounce_interval	= BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
++
+ static struct board_info __initdata board_rta1025w_16 = {
+ 	.name				= "RTA1025W_16",
+ 	.expected_cpu_id		= 0x6348,
+@@ -3842,6 +3958,7 @@ static const struct board_info __initcon
+ 	&board_963281TAN,
+ 	&board_963281T_TEF,
+ 	&board_dsl_274xb_f1,
++	&board_FAST2704V2,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6338
+ 	&board_96338gw,