diff options
| author | David Bauer <mail@david-bauer.net> | 2023-05-06 16:57:18 +0200 |
|---|---|---|
| committer | David Bauer <mail@david-bauer.net> | 2023-07-26 15:37:56 +0200 |
| commit | 897d55bcdf864f4d40cf50396b963ca240bbc1fc (patch) | |
| tree | fe6d0a15209ffbece1ac19751d21aece815fe644 /target/linux/ipq40xx/base-files/etc | |
| parent | 1face854a2fd8c79fc568877068cf9c608a6360e (diff) | |
| download | upstream-897d55bcdf864f4d40cf50396b963ca240bbc1fc.tar.gz upstream-897d55bcdf864f4d40cf50396b963ca240bbc1fc.tar.bz2 upstream-897d55bcdf864f4d40cf50396b963ca240bbc1fc.zip | |
ipq40xx: add support for Teltonika RUTX50
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
Flash: 16MB SPI-NOR (W25Q128)
128MB SPI-NAND (XTX)
WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac)
ETH: 4x LAN ; 1x WAN (Gigabit)
CELL: Quectel RG501Q 3G/4G/5G
UART: Available on the goldfinger connector (Pinout silkscreened)
115200 8N1 3V3 - Only connect RX / TX / GND
Installation
------------
1. Enable SSH in the Teltonika UI
(System --> Administration --> Access Control)
2. Check from which partition set the device is currently running from.
$ cat /proc/boot_info/rootfs/primaryboot
In case this output reads 0, install a Software update from Teltonika
first. After upgrade completion, check this file now reads 1 before
continuing.
2. Transfer the OpenWrt factory image to the device using scp. Use the
same password (user root!) as used for the Web-UI.
$ scp -O openwrt-factory.bin root@192.168.1.1:/tmp
3. Connect to the device using ssh as the root user.
4. Install OpenWrt by writing the factory image to flash.
$ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin
5. Instruct the bootloaer to boot from the first partition set.
$ echo 0 > /proc/boot_info/rootfs/primaryboot
$ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin
$ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin
$ mtd write /tmp/bootconfig.bin /dev/mtd2
$ mtd write /tmp/bootconfig1.bin /dev/mtd3
6. Reboot the device.
$ reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 844bb4bfad84cc6267f9b138d1f63b07ed3b77d0)
Diffstat (limited to 'target/linux/ipq40xx/base-files/etc')
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/board.d/02_network | 1 | ||||
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 6 |
2 files changed, 5 insertions, 2 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 1a74fb792c..c297566dd8 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -24,6 +24,7 @@ ipq40xx_setup_interfaces() p2w,r619ac-64m|\ p2w,r619ac-128m|\ pakedge,wr-1|\ + teltonika,rutx50|\ zyxel,nbg6617) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan" ;; diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 7f41bdcfcc..c8cf297e81 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -131,7 +131,8 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(get_mac_label) 2) ;; - teltonika,rutx10) + teltonika,rutx10|\ + teltonika,rutx50) caldata_extract "0:ART" 0x1000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 2) ;; @@ -227,7 +228,8 @@ case "$FIRMWARE" in caldata_extract "0:ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(get_mac_label) 4) ;; - teltonika,rutx10) + teltonika,rutx10|\ + teltonika,rutx50) caldata_extract "0:ART" 0x5000 0x2f20 ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary "0:CONFIG" 0x0) 3) ;; |