diff options
author | J. Scott Heppler <shep971@centurylink.net> | 2020-09-22 19:30:45 -0700 |
---|---|---|
committer | Adrian Schmutzler <freifunk@adrianschmutzler.de> | 2020-09-23 12:17:32 +0200 |
commit | 620f9c773413a0deaeda2bdc22d5e9cb89b9317f (patch) | |
tree | 6f25bf531d8d71e3aec1bbdfcd67991118355274 /target/linux/ramips/mt7621/base-files/etc/board.d | |
parent | 127ca3c631ea3478d5c9909066b42c117aa72ce0 (diff) | |
download | upstream-620f9c773413a0deaeda2bdc22d5e9cb89b9317f.tar.gz upstream-620f9c773413a0deaeda2bdc22d5e9cb89b9317f.tar.bz2 upstream-620f9c773413a0deaeda2bdc22d5e9cb89b9317f.zip |
ramips: add support for Linksys EA7300 v2
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>
Specifications:
* SoC: MediaTek MT7621A (880 MHz 2c/4t)
* RAM: Winbond W632GG6MB-12 (256M DDR3-1600)
* Flash: Winbond W29N01HVSINA (128M NAND)
* Eth: MediaTek MT7621A (10/100/1000 Mbps x5)
* Radio: MT7603E/MT7615N (2.4 GHz & 5 GHz)
4 antennae: 1 internal and 3 non-deatachable
* USB: 3.0 (x1)
* LEDs:
White (x1 logo)
Green (x6 eth + wps)
Orange (x5, hardware-bound)
* Buttons:
Reset (x1)
WPS (x1)
Installation:
Flash factory image through GUI.
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
Diffstat (limited to 'target/linux/ramips/mt7621/base-files/etc/board.d')
-rwxr-xr-x | target/linux/ramips/mt7621/base-files/etc/board.d/01_leds | 1 | ||||
-rwxr-xr-x | target/linux/ramips/mt7621/base-files/etc/board.d/02_network | 1 |
2 files changed, 2 insertions, 0 deletions
diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index c5cd446809..8c3be541b0 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -42,6 +42,7 @@ gnubee,gb-pc2) ucidef_set_led_netdev "lan2" "lan2" "$boardname:green:lan2" "lan2" ;; linksys,ea7300-v1|\ +linksys,ea7300-v2|\ linksys,ea7500-v2) ucidef_set_led_netdev "lan1" "lan1 link" "$boardname:green:lan1" "lan1" "link" ucidef_set_led_netdev "lan2" "lan2 link" "$boardname:green:lan2" "lan2" "link" diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 1c1d0e4ab7..26063470e8 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -105,6 +105,7 @@ ramips_setup_macs() label_mac=$wan_mac ;; linksys,ea7300-v1|\ + linksys,ea7300-v2|\ linksys,ea7500-v2) lan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) wan_mac=$lan_mac |