ipq40xx: add support for Netgear EX6100v2/EX6150v2

Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	256 MB Winbond W632GU6KB12J
FLASH:	16 MiB Macronix MX25L12805D
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac
	1x1 (EX6100)
	2x2 (EX6150)
INPUT:  Power, WPS, reset button
	AP / Range-extender toggle
LED:	Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL:	Header next to QCA8072 chip.
	VCC, TX, RX, GND (Square hole is VCC)
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from WebIF
 - Factory installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Not Working:
 - AP/Extender toggle-switch

Untested:
 - Support on EX6100v2. They share the same GPL-Code and vendor-images.
   The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
   board-blob. I only own a EX6150v2, therefore i am only able to verify
   functionality on this device.

Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.

Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.

Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.

See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html

Signed-off-by: David Bauer <mail@david-bauer.net>

9 files changed, 446 insertions, 3 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index f1f49abb2e..784fd444dd 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -26,6 +26,11 @@ avm,fritzbox-4040)
 glinet,gl-b1300)
 	ucidef_set_led_wlan "wlan" "WLAN" "${boardname}:green:wlan" "phy0tpt"
 	;;
+netgear,ex6100v2 |\
+netgear,ex6150v2)
+	ucidef_set_led_wlan "wlan2g" "WLAN2G" "ex61x0v2:green:router" "phy0tpt"
+	ucidef_set_led_wlan "wlan5g" "WLAN5G" "ex61x0v2:green:client" "phy1tpt"
+	;;
 meraki,mr33)
 	ucidef_set_interface_lan "eth0"
 	;;
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 91343cd4b4..ade1b05458 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -41,8 +41,9 @@ glinet,gl-b1300)
 openmesh,a42)
 	ucidef_set_interfaces_lan_wan "eth1" "eth0"
 	;;
-
-meraki,mr33)
+meraki,mr33 |\
+netgear,ex6100v2 |\
+netgear,ex6150v2)
 	ucidef_set_interface_lan "eth0"
 	;;
 *)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 56c10cbf00..0a5780cbf0 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -129,6 +129,11 @@ case "$FIRMWARE" in
 		ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064
 		ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +2)
 		;;
+	netgear,ex6100v2 |\
+	netgear,ex6150v2)
+		ath10kcal_extract "ART" 4096 12064
+		ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 0)
+		;;
 	compex,wpj428 |\
 	openmesh,a42)
 		ath10kcal_extract "0:ART" 4096 12064
@@ -154,6 +159,11 @@ case "$FIRMWARE" in
 		ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064
 		ath10kcal_patch_mac_crc $(macaddr_add $(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) +3)
 		;;
+	netgear,ex6100v2 |\
+	netgear,ex6150v2)
+		ath10kcal_extract "ART" 20480 12064
+		ath10kcal_patch_mac_crc $(mtd_get_mac_binary dnidata 12)
+		;;
 	compex,wpj428 |\
 	openmesh,a42)
 		ath10kcal_extract "0:ART" 20480 12064
diff --git a/target/linux/ipq40xx/config-4.14 b/target/linux/ipq40xx/config-4.14
index 1bba061761..18a8bafd5f 100644
--- a/target/linux/ipq40xx/config-4.14
+++ b/target/linux/ipq40xx/config-4.14
@@ -191,6 +191,7 @@ CONFIG_GENERIC_STRNLEN_USER=y
 CONFIG_GENERIC_TIME_VSYSCALL=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_WATCHDOG=y
 # CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
@@ -438,6 +439,7 @@ CONFIG_SMP_ON_UP=y
 CONFIG_SPARSE_IRQ=y
 CONFIG_SPI=y
 CONFIG_SPI_MASTER=y
+CONFIG_SPI_GPIO=y
 CONFIG_SPI_QUP=y
 CONFIG_SPMI=y
 CONFIG_SPMI_MSM_PMIC_ARB=y
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts
new file mode 100644
index 0000000000..a0abe41517
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6100v2.dts
@@ -0,0 +1,33 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear EX6100v2";
+	compatible = "netgear,ex6100v2", "qcom,ipq4019";
+};
+
+&wifi0 {
+	qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
+
+&wifi1 {
+	qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts
new file mode 100644
index 0000000000..e0b5c38b33
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex6150v2.dts
@@ -0,0 +1,33 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear EX6150v2";
+	compatible = "netgear,ex6150v2", "qcom,ipq4019";
+};
+
+&wifi0 {
+	qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
+
+&wifi1 {
+	qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi
new file mode 100644
index 0000000000..14c1caa969
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ex61x0v2.dtsi
@@ -0,0 +1,322 @@
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include "qcom-ipq4019-bus.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "Netgear EX61X0v2";
+	compatible = "netgear,ex61x0v2", "qcom,ipq4019";
+
+	reserved-memory {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges;
+
+		smem@87e00000 {
+			reg = <0x87e00000 0x080000>;
+			no-map;
+		};
+
+		tz@87e80000 {
+			reg = <0x87e80000 0x180000>;
+			no-map;
+		};
+	};
+
+	soc {
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		serial@78af000 {
+			pinctrl-0 = <&serial_pins>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	aliases {
+		led-boot = &power_amber;
+		led-failsafe = &power_amber;
+		led-running = &power_green;
+		led-upgrade = &power_amber;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		wps {
+			label = "wps";
+			gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WPS_BUTTON>;
+		};
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	led_spi {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		ranges;
+
+		gpio-sck = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <0>;
+
+		led_gpio: led_gpio@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			registers-number = <1>;
+			spi-max-frequency = <1000000>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		power_amber: power_amber {
+			label = "ex61x0v2:amber:power";
+			gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
+		};
+
+		power_green: power_green {
+			label = "ex61x0v2:green:power";
+			gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
+		};
+
+		right {
+			label = "ex61x0v2:blue:right";
+			gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		left {
+			label = "ex61x0v2:blue:left";
+			gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+		};
+
+		client_green {
+			label = "ex61x0v2:green:client";
+			gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+		};
+
+		client_red {
+			label = "ex61x0v2:red:client";
+			gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+		};
+
+		router_green {
+			label = "ex61x0v2:green:router";
+			gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+		};
+
+		router_red {
+			label = "ex61x0v2:red:router";
+			gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "ex61x0v2:green:wps";
+			gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&tlmm {
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio60", "gpio61";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pin {
+			function = "blsp_spi0";
+			pins = "gpio55", "gpio56", "gpio57";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pin_cs {
+			function = "gpio";
+			pins = "gpio54";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&spi_0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+	mx25l12805d@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+
+			partition1@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+
+			partition2@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+
+			partition3@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+
+			partition4@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+
+			partition5@E0000 {
+				label = "APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+
+			partition6@F0000 {
+				label = "APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+
+			partition7@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+
+			partition8@180000 {
+				label = "config";
+				reg = <0x00180000 0x00010000>;
+				read-only;
+			};
+
+			partition9@190000 {
+				label = "pot";
+				reg = <0x00190000 0x00010000>;
+				read-only;
+			};
+
+			partition10@1a0000 {
+				label = "dnidata";
+				reg = <0x001a0000 0x00010000>;
+				read-only;
+			};
+
+			partition11@1b0000 {
+				label = "firmware";
+				reg = <0x001b0000 0x00e10000>;
+			};
+
+			partition12@fc0000 {
+				label = "language";
+				reg = <0x00fc0000 0x00040000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&wifi0 {
+	status = "okay";
+};
+
+&wifi1 {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 87545d08de..c13516e6dc 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -31,6 +31,18 @@ define Device/UbiFit
 	IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata
 endef
 
+define Device/DniImage
+	KERNEL_SUFFIX := -fit-uImage.itb
+	KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb
+	KERNEL_NAME := Image
+	NETGEAR_BOARD_ID :=
+	NETGEAR_HW_ID :=
+	IMAGES := factory.img sysupgrade.bin
+	IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | netgear-dni
+	IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakeroot-hdr | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | append-metadata
+endef
+DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
+
 
 define Device/8dev_jalapeno
 	$(call Device/FitImage)
@@ -113,6 +125,29 @@ define Device/meraki_mr33
 endef
 TARGET_DEVICES += meraki_mr33
 
+define Device/netgear_ex61x0v2
+	$(call Device/DniImage)
+	KERNEL_SIZE := 3080192
+	DEVICE_DTS_CONFIG := config@4
+	DEVICE_PACKAGES := ath10k-firmware-qca4019 ipq-wifi-netgear_ex61x0v2
+	NETGEAR_BOARD_ID := EX6150v2series
+	NETGEAR_HW_ID := 29765285+16+0+128+2x2
+endef
+
+define Device/netgear_ex6100v2
+	$(call Device/netgear_ex61x0v2)
+	DEVICE_DTS := qcom-ipq4018-ex6100v2
+	DEVICE_TITLE := Netgear EX6100v2
+endef
+TARGET_DEVICES += netgear_ex6100v2
+
+define Device/netgear_ex6150v2
+	$(call Device/netgear_ex61x0v2)
+	DEVICE_DTS := qcom-ipq4018-ex6150v2
+	DEVICE_TITLE := Netgear EX6150v2
+endef
+TARGET_DEVICES += netgear_ex6150v2
+
 define Device/openmesh_a42
 	$(call Device/FitImageLzma)
 	DEVICE_DTS := qcom-ipq4018-a42
diff --git a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
index 9c09c1fa78..99417d3e36 100644
--- a/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.14/069-arm-boot-add-dts-files.patch
@@ -10,11 +10,13 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -697,7 +697,15 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -697,7 +697,17 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
 +	qcom-ipq4018-a42.dtb \
++	qcom-ipq4018-ex6100v2.dtb \
++	qcom-ipq4018-ex6150v2.dtb \
 +	qcom-ipq4018-fritz4040.dtb \
 +	qcom-ipq4018-jalapeno.dtb \
 +	qcom-ipq4018-rt-ac58u.dtb \