ramips: add support for Xiaomi Mi Router 3 Pro

Hardware:

CPU:   MediaTek MT7621AT (2x880MHz)
RAM:   512MB DDR3
FLASH: 256MB NAND
WiFi:  2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!)
WiFI:  5GHz 4x4 MT7615 a/n/ac  (Needs driver, See Issues!)
USB:   1x 3.0
ETH:   1x WAN 10/100/1000 3x LAN 10/100/1000
LED:   Power/Status
BTN:   RESET
UART:  115200 8n1

Partition layout and boot:

Stock Xiaomi firmware has the MTD split into (among others)

- kernel0 (@0x200000)
- kernel1 (@0x600000)
- rootfs0
- rootfs1
- overlay (ubi)

Xiaomi uboot expects to find kernels at 0x200000 & 0x600000
referred to as system 1 & system 2 respectively.
a kernel is considered suitable for handing control over
if its linux magic number exists & uImage CRC are correct.
If either of those conditions fail, a matching sys'n'_fail flag
is set in uboot env & a restart performed in the hope that the
alternate kernel is okay.
If neither kernel checksums ok and both are marked failed, system 2
is booted anyway.

Note uboot's tftp flash install writes the transferred
image to both kernel partitions.

Installation:

Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in
kernel0 for ease of recovery, and install OpenWRT into kernel1 and
after.

The installation file for OpenWRT is a *squashfs-factory.bin file that
contains the kernel and a ubi partition. This is flashed as follows:

nvram set flag_try_sys1_failed=1
nvram set flag_try_sys2_failed=0
nvram commit
dd if=factory.bin bs=1M count=4 | mtd write - kernel1
dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0
reboot

Reverting to stock:

The part of stock firmware we've kept in kernel0 allows us to run stock
recovery, which will re-flash stock firmware from a *.bin file on a USB.

For this we do the following:

fw_setenv flag_try_sys1_failed 0
fw_setenv flag_try_sys2_failed 1
reboot

After reboot the LED status light will blink red, at which point pressing
the 'reset' button will cause stock firmware to be installed from USB.

Issues:

OpenWRT currently does not have support for the MT7615 wifi chips. There is
ongoing work to add mt7615 support to the open source mt76 driver. Until that
support is in place, there are closed-source kernel modules that can be used.

See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170

Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[02_network remaps, Added link to notes]

5 files changed, 221 insertions, 2 deletions

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 3a761decb1..9cca231ab6 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -235,6 +235,12 @@ mikrotik,rbm11g)
 miniembplug)
 	set_wifi_led "$boardname:red:wlan"
 	;;
+xiaomi,mir3p)
+	ucidef_set_led_switch "wan-amber"  "WAN (amber)"  "$boardname:amber:wan"  "switch0" "0x10" "0x08"
+	ucidef_set_led_switch "lan1-amber" "LAN1 (amber)" "$boardname:amber:lan1" "switch0" "0x02" "0x08"
+	ucidef_set_led_switch "lan2-amber" "LAN2 (amber)" "$boardname:amber:lan2" "switch0" "0x04" "0x08"
+	ucidef_set_led_switch "lan3-amber" "LAN3 (amber)" "$boardname:amber:lan3" "switch0" "0x08" "0x08"
+	;;
 mir3g)
 	ucidef_set_led_switch "wan-amber"  "WAN (amber)"  "$boardname:amber:wan"  "switch0" "0x02" "0x08"
 	ucidef_set_led_switch "lan1-amber" "LAN1 (amber)" "$boardname:amber:lan1" "switch0" "0x08" "0x08"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 5221838547..890efa0d93 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -436,6 +436,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"4:lan" "0:wan" "6@eth0"
 		;;
+	xiaomi,mir3p)
+		ucidef_add_switch "switch0" \
+			"1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "6@eth0"
+		;;
 	zbtlink,zbt-we1226|\
 	y1)
 		ucidef_add_switch "switch0" \
@@ -562,7 +566,8 @@ ramips_setup_macs()
 		lan_mac=$(mtd_get_mac_binary factory_info 13)
 		wan_mac=$(macaddr_add "$lan_mac" 1)
 		;;
-	mir3g)
+	mir3g|\
+	xiaomi,mir3p)
 		lan_mac=$(mtd_get_mac_binary Factory 0xe006)
 		;;
 	miwifi-mini)
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 14e9ac3d14..67b0f3e7f4 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -41,7 +41,8 @@ platform_do_upgrade() {
 	r6220|\
 	netgear,r6350|\
 	ubnt-erx|\
-	ubnt-erx-sfp)
+	ubnt-erx-sfp|\
+	xiaomi,mir3p)
 		nand_do_upgrade "$ARGV"
 		;;
 	tplink,c50-v4)
diff --git a/target/linux/ramips/dts/MIR3P.dts b/target/linux/ramips/dts/MIR3P.dts
new file mode 100644
index 0000000000..cd929e5e33
--- /dev/null
+++ b/target/linux/ramips/dts/MIR3P.dts
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	compatible = "xiaomi,mir3p", "mediatek,mt7621-soc";
+	model = "Xiaomi Mi Router 3 Pro";
+
+	aliases {
+		led-boot = &led_status_yellow;
+		led-failsafe = &led_status_red;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_yellow;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x1c000000>, <0x20000000 0x04000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status_red: status_red {
+			label = "mir3p:red:status";
+			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_blue: status_blue {
+			label = "mir3p:blue:status";
+			gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led_status_yellow: status_yellow {
+			label = "mir3p:yellow:status";
+			gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+		};
+
+		wan_amber {
+			label = "mir3p:amber:wan";
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+
+		lan3_amber {
+			label = "mir3p:amber:lan3";
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+
+		lan2_amber {
+			label = "mir3p:amber:lan2";
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		lan1_amber {
+			label = "mir3p:amber:lan1";
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	button {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	reg_usb_vbus: regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&xhci {
+	vbus-supply = <&reg_usb_vbus>;
+};
+
+&nand {
+	status = "okay";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "Bootloader";
+			reg = <0x0 0x40000>;
+			read-only;
+		};
+
+		partition@40000 {
+			label = "Config";
+			reg = <0x40000 0x40000>;
+		};
+
+		partition@80000 {
+			label = "Bdata";
+			reg = <0x80000 0x40000>;
+			read-only;
+		};
+
+		factory: partition@c0000 {
+			label = "Factory";
+			reg = <0x0c0000 0x40000>;
+			read-only;
+		};
+
+		partition@100000 {
+			label = "crash";
+			reg = <0x100000 0x40000>;
+		};
+
+		partition@140000 {
+			label = "crash_syslog";
+			reg = <0x140000 0x80000>;
+		};
+
+		partition@1c0000 {
+			label = "reserved0";
+			reg = <0x1c0000 0x40000>;
+			read-only;
+		};
+
+		/* We keep stock xiaomi firmware (kernel0) here */
+		partition@200000 {
+			label = "kernel_stock";
+			reg = <0x200000 0x400000>;
+		};
+
+		partition@600000 {
+			label = "kernel";
+			reg = <0x600000 0x400000>;
+		};
+
+		partition@a00000 {
+			label = "ubi";
+			reg = <0xa00000 0xf580000>;
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pcie0 {
+	wifi@0,0 {
+		compatible = "pci14c3,7615";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x0000>;
+	};
+};
+
+&pcie1 {
+	wifi@0,0 {
+		compatible = "pci14c3,7615";
+		reg = <0x0000 0 0 0 0>;
+		mediatek,mtd-eeprom = <&factory 0x8000>;
+		ieee80211-freq-limit = <5000000 6000000>;
+	};
+};
+
+&ethernet {
+	mtd-mac-address = <&factory 0xe000>;
+	mediatek,portmap = "llllw";
+};
+
+&pinctrl {
+	state_default: pinctrl0 {
+		gpio {
+			ralink,group = "jtag", "uart2", "uart3", "wdt";
+			ralink,function = "gpio";
+		};
+	};
+};
diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index 06f8bef86e..8b0b28a941 100644
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -235,6 +235,22 @@ define Device/k2p
 endef
 TARGET_DEVICES += k2p
 
+define Device/xiaomi_mir3p
+  DTS := MIR3P
+  BLOCKSIZE := 128k
+  PAGESIZE := 2048
+  KERNEL_SIZE:= 4096k
+  UBINIZE_OPTS := -E 5
+  IMAGE_SIZE := $(ralink_default_fw_size_32M)
+  DEVICE_TITLE := Xiaomi Mi Router 3 Pro
+  IMAGES += factory.bin
+  IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
+  IMAGE/factory.bin := append-kernel | pad-to $$(KERNEL_SIZE) | append-ubi | check-size $$$$(IMAGE_SIZE)
+  DEVICE_PACKAGES := \
+	kmod-usb3 kmod-usb-ledtrig-usbport wpad-basic uboot-envtools
+endef
+TARGET_DEVICES += xiaomi_mir3p
+
 define Device/mir3g
   DTS := MIR3G
   BLOCKSIZE := 128k