mpc85xx: add support for Enterasys WS-AP3710i

Hardware
--------

SoC:   NXP P1020 (2x e500 @ 800MHz)
RAM:   256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN:   1x Reset
WiFi:  1x Atheros AR9590 2.4 bgn 3x3
       2x Atheros AR9590 5.0 an 3x3
ETH:   1x Gigabit Ethernet (Atheros AR8033)
LED:   System (green/red) - Radio{0,1} (green)
       LAN (connected to PHY)
        - GE blue
        - FE green

Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.

Installation
------------

1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in
   the root directory of a TFTP server and serve it at
   192.168.200.200/24.

2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
   by pressing Enter when prompted. Credentials are identical to the one
   in the APs interface. By default it is admin / new2day.

3. Set the bootcmd so the AP can boot OpenWrt by executing

   $ setenv boot_openwrt "setenv bootargs;
     cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
   $ setenv bootcmd "run boot_openwrt"
   $ saveenv

   If you plan on going back to the vendor firmware - the bootcmd for it
   is stored in the boot_flash variable.

4. Load the initramfs image to RAM and boot by executing

   $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm

5. Make a backup of the "firmware" partition if you ever wish to go back
   to the vendor firmware.

6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
   folder.

7. Flash OpenWrt using sysupgrade.

   $ sysupgrade -n /tmp/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>

7 files changed, 310 insertions, 0 deletions

diff --git a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
index f153b53c8e..cd829cb471 100644
--- a/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
+++ b/target/linux/mpc85xx/base-files/etc/hotplug.d/ieee80211/10-fix-wifi-mac
@@ -12,6 +12,9 @@ PHYNBR=${DEVPATH##*/phy}
 board=$(board_name)
 
 case "$board" in
+enterasys,ws-ap3710i)
+	echo $(mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR}) > /sys${DEVPATH}/macaddress
+	;;
 ocedo,panda)
 	WMAC=wmac$(($PHYNBR + 1))
 	MAC=$(mtd_get_mac_ascii uboot-env0 ${WMAC})
diff --git a/target/linux/mpc85xx/config-4.19 b/target/linux/mpc85xx/config-4.19
index 9c7b49cfdf..6395ad72ff 100644
--- a/target/linux/mpc85xx/config-4.19
+++ b/target/linux/mpc85xx/config-4.19
@@ -318,6 +318,7 @@ CONFIG_VDSO32=y
 # CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set
 CONFIG_VM_EVENT_COUNTERS=y
 CONFIG_WATCHDOG_CORE=y
+# CONFIG_WS_AP3710I is not set
 # CONFIG_XES_MPC85xx is not set
 # CONFIG_XPS_USB_HCD_XILINX is not set
 CONFIG_XZ_DEC_BCJ=y
diff --git a/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3710i.dts b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3710i.dts
new file mode 100644
index 0000000000..ebaac417eb
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/boot/dts/ws-ap3710i.dts
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0-or-later or MIT
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+	model = "Enterasys WS-AP3710i";
+	compatible = "enterasys,ws-ap3710i";
+
+	aliases {
+		led-boot = &led_power_green;
+		led-failsafe = &led_power_red;
+		led-running = &led_power_green;
+		led-upgrade = &led_power_red;
+		label-mac-device = &enet0;
+	};
+
+	memory {
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wifi1 {
+			gpios = <&gpio0 3 0>;
+			label = "ws-ap3710i:green:radio1";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wifi2 {
+			gpios = <&gpio0 4 0>;
+			label = "ws-ap3710i:green:radio2";
+			linux,default-trigger = "phy1tpt";
+		};
+
+		led_power_green: power_green {
+			gpios = <&gpio0 8 0>;
+			label = "ws-ap3710i:green:power";
+		};
+
+		led_power_red: power_red {
+			gpios = <&gpio0 9 0>;
+			label = "ws-ap3710i:red:power";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset button";
+			gpios = <&gpio0 1 1>; /* active low */
+			linux,code = <0x198>; /* KEY_RESTART */
+		};
+	};
+
+	lbc: localbus@ffe05000 {
+		reg = <0 0xffe05000 0 0x1000>;
+		ranges = <0x0 0x0 0x0 0xee000000 0x2000000>;
+
+		nor@0,0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "cfi-flash";
+			reg = <0x0 0x0 0x2000000>;
+			bank-width = <2>;
+			device-width = <1>;
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					compatible = "denx,fit";
+					reg = <0x0 0x1d80000>;
+					label = "firmware";
+				};
+
+				partition@1d80000 {
+					reg = <0x1d80000 0x80000>;
+					label = "u-boot";
+					read-only;
+				};
+
+				partition@1e00000 {
+					reg = <0x1e00000 0x100000>;
+					label = "nvram";
+					read-only;
+				};
+
+				partition@1f00000 {
+					reg = <0x1f00000 0x20000>;
+					label = "cfg2";
+					read-only;
+				};
+
+				partition@1f20000 {
+					reg = <0x1f20000 0x20000>;
+					label = "cfg1";
+					read-only;
+				};
+			};
+		};
+	};
+
+	soc: soc@ffe00000 {
+		ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+		gpio0: gpio-controller@fc00 {
+		};
+
+		mdio@24000 {
+			phy4: ethernet-phy@4 {
+				reg = <0x4>;
+				reset-gpios = <&gpio0 2 1>;
+			};
+		};
+
+		enet0: ethernet@b0000 {
+			phy-connection-type = "rgmii-id";
+			phy-handle = <&phy4>;
+		};
+
+		enet1: ethernet@b1000 {
+			status = "disabled";
+		};
+
+		enet2: ethernet@b2000 {
+			status = "disabled";
+		};
+
+		usb@22000 {
+			status = "disabled";
+		};
+
+		usb@23000 {
+			status = "disabled";
+		};
+	};
+
+	pci0: pcie@ffe09000 {
+		ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+		reg = <0 0xffe09000 0 0x1000>;
+		pcie@0 {
+			ranges = <0x2000000 0x0 0xa0000000
+				  0x2000000 0x0 0xa0000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+	pci1: pcie@ffe0a000 {
+		reg = <0 0xffe0a000 0 0x1000>;
+		ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+			  0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+		pcie@0 {
+			ranges = <0x2000000 0x0 0x80000000
+				  0x2000000 0x0 0x80000000
+				  0x0 0x20000000
+
+				  0x1000000 0x0 0x0
+				  0x1000000 0x0 0x0
+				  0x0 0x100000>;
+		};
+	};
+
+};
+/include/ "fsl/p1020si-post.dtsi"
diff --git a/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3710i.c b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3710i.c
new file mode 100644
index 0000000000..a2900868b9
--- /dev/null
+++ b/target/linux/mpc85xx/files/arch/powerpc/platforms/85xx/ws-ap3710i.c
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * Enterasys WS-AP3710i Board Setup
+ *
+ * Copyright (C) 2019 David Bauer <mail@david-bauer.net>
+ *
+ * Based on:
+ *   mpc85xx_rdb.c:
+ *      MPC85xx RDB Board Setup
+ *      Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include "smp.h"
+
+#include "mpc85xx.h"
+
+void __init ws_ap3710i_pic_init(void)
+{
+	struct mpic *mpic;
+
+	mpic = mpic_alloc(NULL, 0,
+	  MPIC_BIG_ENDIAN |
+	  MPIC_SINGLE_DEST_CPU,
+	  0, 256, " OpenPIC  ");
+
+	BUG_ON(mpic == NULL);
+	mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init ws_ap3710i_setup_arch(void)
+{
+	if (ppc_md.progress)
+		ppc_md.progress("ws_ap3710i_setup_arch()", 0);
+
+	mpc85xx_smp_init();
+
+	fsl_pci_assign_primary();
+
+	pr_info("WS-AP3710i board from Enterasys\n");
+}
+
+machine_arch_initcall(ws_ap3710i, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ws_ap3710i_probe(void)
+{
+	if (of_machine_is_compatible("enterasys,ws-ap3710i"))
+		return 1;
+	return 0;
+}
+
+define_machine(ws_ap3710i) {
+	.name			= "P1020 RDB",
+	.probe			= ws_ap3710i_probe,
+	.setup_arch		= ws_ap3710i_setup_arch,
+	.init_IRQ		= ws_ap3710i_pic_init,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+	.pcibios_fixup_phb      = fsl_pcibios_fixup_phb,
+#endif
+	.get_irq		= mpic_get_irq,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+};
diff --git a/target/linux/mpc85xx/image/Makefile b/target/linux/mpc85xx/image/Makefile
index ee1663018e..5ca16909e7 100644
--- a/target/linux/mpc85xx/image/Makefile
+++ b/target/linux/mpc85xx/image/Makefile
@@ -102,6 +102,16 @@ define Device/aerohive_hiveap-330
 endef
 TARGET_DEVICES += aerohive_hiveap-330
 
+define Device/enterasys_ws-ap3710i
+  DEVICE_VENDOR := Enterasys
+  DEVICE_MODEL := WS-AP3710i
+  BLOCKSIZE := 128k
+  KERNEL = kernel-bin | lzma | fit lzma $(KDIR)/image-$$(DEVICE_DTS).dtb
+  IMAGES := sysupgrade.bin
+  IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += enterasys_ws-ap3710i
+
 define Device/ocedo_panda
   DEVICE_VENDOR := OCEDO
   DEVICE_MODEL := Panda
diff --git a/target/linux/mpc85xx/p1020/config-default b/target/linux/mpc85xx/p1020/config-default
index 01c18e4d59..2ad3f75bee 100644
--- a/target/linux/mpc85xx/p1020/config-default
+++ b/target/linux/mpc85xx/p1020/config-default
@@ -23,6 +23,8 @@ CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ECC=y
 CONFIG_MTD_NAND_FSL_ELBC=y
 CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_FIT_FW=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_BEB_LIMIT=20
 CONFIG_MTD_UBI_BLOCK=y
@@ -51,4 +53,5 @@ CONFIG_UBIFS_FS=y
 CONFIG_UBIFS_FS_ADVANCED_COMPR=y
 CONFIG_UBIFS_FS_LZO=y
 CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_WS_AP3710I=y
 CONFIG_XPS=y
diff --git a/target/linux/mpc85xx/patches-4.19/106-powerpc-85xx-ws-ap3710i-support.patch b/target/linux/mpc85xx/patches-4.19/106-powerpc-85xx-ws-ap3710i-support.patch
new file mode 100644
index 0000000000..4bacedbcd7
--- /dev/null
+++ b/target/linux/mpc85xx/patches-4.19/106-powerpc-85xx-ws-ap3710i-support.patch
@@ -0,0 +1,30 @@
+--- a/arch/powerpc/platforms/85xx/Kconfig
++++ b/arch/powerpc/platforms/85xx/Kconfig
+@@ -71,6 +71,17 @@ config PANDA
+ 	  This board is a Concurrent Dual-Band wireless access point with a
+ 	  Freescale P1020 SoC.
+ 
++config WS_AP3710I
++	bool "Enterasys WS-AP3710i"
++	select DEFAULT_UIMAGE
++	select ARCH_REQUIRE_GPIOLIB
++	select GPIO_MPC8XXX
++	help
++	  This option enables support for the Enterasys WS-AP3710i board.
++
++	  This board is a Concurrent Dual-Band wireless access point with a
++	  Freescale P1020 SoC.
++
+ config MPC8540_ADS
+ 	bool "Freescale MPC8540 ADS"
+ 	select DEFAULT_UIMAGE
+--- a/arch/powerpc/platforms/85xx/Makefile
++++ b/arch/powerpc/platforms/85xx/Makefile
+@@ -24,6 +24,7 @@ obj-$(CONFIG_P1022_RDK)   += p1022_rdk.o
+ obj-$(CONFIG_P1023_RDB)   += p1023_rdb.o
+ obj-$(CONFIG_PANDA)       += panda.o
+ obj-$(CONFIG_TWR_P102x)   += twr_p102x.o
++obj-$(CONFIG_WS_AP3710I)  += ws-ap3710i.o
+ obj-$(CONFIG_CORENET_GENERIC)   += corenet_generic.o
+ obj-$(CONFIG_FB_FSL_DIU)	+= t1042rdb_diu.o
+ obj-$(CONFIG_RED_15W_REV1)	+= red15w_rev1.o