ipq40xx: add support for EnGenius EAP2200

SOC:    IPQ4019 / QCA Dakota
CPU:    Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM:   256 MiB
FLASH:  NOR 4 MiB + NAND 128 MiB
ETH:    Qualcomm Atheros QCA8072
WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2:  Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT:  WPS Button
LEDS:   Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE

1. Load Ramdisk via U-Boot

To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
   * 115200bps
   * 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.

U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm

Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

10 files changed, 599 insertions, 7 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
index 0326bab382..dd7f35a0a3 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds
@@ -33,6 +33,10 @@ engenius,eap1300)
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:yellow:wlan5g" "phy1tpt"
 	ucidef_set_led_default "mesh" "MESH" "${boardname}:blue:mesh" "0"
 	;;
+engenius,eap2200)
+	ucidef_set_led_netdev "lan1" "LAN1" "${boardname}:blue:lan1" "eth0"
+	ucidef_set_led_netdev "lan2" "LAN2" "${boardname}:blue:lan2" "eth1"
+	;;
 engenius,ens620ext)
 	ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2G" "phy0tpt"
 	ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5G" "phy1tpt"
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 4b636fc701..190286541a 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -58,7 +58,8 @@ ipq40xx_setup_interfaces()
 		;;
 	avm,fritzrepeater-3000|\
 	compex,wpj419|\
-	compex,wpj428)
+	compex,wpj428|\
+	engenius,eap2200)
 		ucidef_set_interface_lan "eth0 eth1"
 		;;
 	ezviz,cs-w3-wd1200g-eup)
@@ -109,6 +110,7 @@ ipq40xx_setup_macs()
 		lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
 		label_mac=$lan_mac
 		;;
+	engenius,eap220|\
 	engenius,emd1)
 		lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
 		label_mac=$lan_mac
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 957bee12ab..50bfbb0a86 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -31,14 +31,15 @@ case "$FIRMWARE" in
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C800 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") || \
 		/usr/bin/fritz_cal_extract -i 1 -s 0x3C000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1")
 		;;
+	engenius,eap2200 |\
+	openmesh,a62)
+		caldata_extract "0:ART" 0x9000 0x2f20
+		;;
 	linksys,ea8300)
 		caldata_extract "ART" 0x9000 0x2f20
 		# OEM assigns 4 sequential MACs
 		ath10k_patch_mac $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4))
 		;;
-	openmesh,a62)
-		caldata_extract "0:ART" 0x9000 0x2f20
-		;;
 	esac
 	;;
 "ath10k/pre-cal-ahb-a000000.wifi.bin")
@@ -80,6 +81,7 @@ case "$FIRMWARE" in
 	compex,wpj419 |\
 	compex,wpj428 |\
 	engenius,eap1300 |\
+	engenius,eap2200 |\
 	openmesh,a42 |\
 	openmesh,a62 |\
 	qxwlan,e2600ac-c1 |\
@@ -159,6 +161,7 @@ case "$FIRMWARE" in
 	compex,wpj419 |\
 	compex,wpj428 |\
 	engenius,eap1300 |\
+	engenius,eap2200 |\
 	openmesh,a42 |\
 	openmesh,a62 |\
 	qxwlan,e2600ac-c1 |\
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 1bca152a38..f9ec8ab055 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -13,6 +13,10 @@ preinit_set_mac_address() {
 		ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
 		ip link set dev eth1 address $(mtd_get_mac_binary "ART" 0x0)
 		;;
+	engenius,eap2200)
+		base_mac=$(cat /sys/class/net/eth0/address)
+		ip link set dev eth1 address $(macaddr_add "${base_mac}" +1)
+		;;
 	linksys,ea8300)
 		base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
 		ip link set dev eth0 address "${base_mac}"
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index cdf7a2b8f2..377f65ea42 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -53,6 +53,7 @@ platform_do_upgrade() {
 	avm,fritzrepeater-1200 |\
 	avm,fritzrepeater-3000 |\
 	cilab,meshpoint-one |\
+	engenius,eap2200 |\
 	qxwlan,e2600ac-c2)
 		nand_do_upgrade "$1"
 		;;
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
new file mode 100644
index 0000000000..6862ca87e3
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "EnGenius EAP2200";
+	compatible = "engenius,eap2200";
+
+	keys {
+			compatible = "gpio-keys";
+
+			wps {
+				label = "wps";
+				gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+				linux,code = <KEY_WPS_BUTTON>;
+			};
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "eap2200:amber:power";
+			gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+		};
+
+		lan1 {
+			label = "eap2200:blue:lan1";
+			gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+		};
+
+		lan2 {
+			label = "eap2200:blue:lan2";
+			gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g {
+			label = "eap2200:blue:wlan2g";
+			gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "eap2200:yellow:wlan5g";
+			gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wlan5g2 {
+			label = "eap2200:yellow:wlan5g2";
+			gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy2tpt";
+		};
+
+		mode {
+			label = "eap2200:blue:mode";
+			gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_lan_bmp = <0x10>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "0:SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition1@40000 {
+				label = "0:MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition2@60000 {
+				label = "0:QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition3@c0000 {
+				label = "0:CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition4@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition5@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition6@f0000 {
+				label = "0:APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition7@170000 {
+				label = "0:ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac0 {
+	vlan_tag = <1 0x10>;
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "rootfs1";
+				reg = <0x00000000 0x04000000>;
+			};
+			partition@40000000 {
+				label = "ubi";
+				reg = <0x04000000 0x04000000>;
+			};
+
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi2: wifi@1,0 {
+			compatible = "qcom,ath10k";
+			reg = <0x00010000 0 0 0 0>;
+			ieee80211-freq-limit = <5470000 5875000>;
+			qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+		};
+	};
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	serial_0_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
+
+&wifi1 {
+	status = "okay";
+	ieee80211-freq-limit = <5170000 5350000>;
+	qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
new file mode 100644
index 0000000000..6862ca87e3
--- /dev/null
+++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-eap2200.dts
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "EnGenius EAP2200";
+	compatible = "engenius,eap2200";
+
+	keys {
+			compatible = "gpio-keys";
+
+			wps {
+				label = "wps";
+				gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+				linux,code = <KEY_WPS_BUTTON>;
+			};
+	};
+
+	aliases {
+		led-boot = &led_power;
+		led-failsafe = &led_power;
+		led-running = &led_power;
+		led-upgrade = &led_power;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: power {
+			label = "eap2200:amber:power";
+			gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+		};
+
+		lan1 {
+			label = "eap2200:blue:lan1";
+			gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+		};
+
+		lan2 {
+			label = "eap2200:blue:lan2";
+			gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+		};
+
+		wlan2g {
+			label = "eap2200:blue:wlan2g";
+			gpios = <&tlmm 46 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "eap2200:yellow:wlan5g";
+			gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		wlan5g2 {
+			label = "eap2200:yellow:wlan5g2";
+			gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy2tpt";
+		};
+
+		mode {
+			label = "eap2200:blue:mode";
+			gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+			switch_lan_bmp = <0x10>;
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition0@0 {
+				label = "0:SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition1@40000 {
+				label = "0:MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition2@60000 {
+				label = "0:QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition3@c0000 {
+				label = "0:CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition4@d0000 {
+				label = "0:DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition5@e0000 {
+				label = "0:APPSBLENV";
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition6@f0000 {
+				label = "0:APPSBL";
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition7@170000 {
+				label = "0:ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&blsp1_uart1 {
+	pinctrl-0 = <&serial_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&gmac0 {
+	vlan_tag = <1 0x10>;
+};
+
+&nand {
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "rootfs1";
+				reg = <0x00000000 0x04000000>;
+			};
+			partition@40000000 {
+				label = "ubi";
+				reg = <0x04000000 0x04000000>;
+			};
+
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi2: wifi@1,0 {
+			compatible = "qcom,ath10k";
+			reg = <0x00010000 0 0 0 0>;
+			ieee80211-freq-limit = <5470000 5875000>;
+			qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+		};
+	};
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	nand_pins: nand_pins {
+		pullups {
+			pins = "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56",
+				"gpio57", "gpio60", "gpio61",
+				"gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67",
+				"gpio68", "gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	serial_0_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+};
+
+&wifi0 {
+	status = "okay";
+	qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
+
+&wifi1 {
+	status = "okay";
+	ieee80211-freq-limit = <5170000 5350000>;
+	qcom,ath10k-calibration-variant = "EnGenius-EAP2200";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index bbe4df9df4..9ddcd17f1d 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -278,6 +278,18 @@ define Device/engenius_eap1300
 endef
 TARGET_DEVICES += engenius_eap1300
 
+define Device/engenius_eap2200
+	$(call Device/FitImage)
+	$(call Device/UbiFit)
+	DEVICE_VENDOR := EnGenius
+	DEVICE_MODEL := EAP2200
+	SOC := qcom-ipq4019
+	BLOCKSIZE := 128k
+	PAGESIZE := 2048
+	DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-engenius_eap2200 -kmod-ath10k-ct kmod-ath10k-ct-smallbuffers
+endef
+TARGET_DEVICES += engenius_eap2200
+
 define Device/engenius_emd1
 	$(call Device/FitImage)
 	DEVICE_VENDOR := EnGenius
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index 11e775a5dc..89e665db23 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -36,6 +36,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
  	qcom-ipq4019-ap.dk07.1-c1.dtb \
  	qcom-ipq4019-ap.dk07.1-c2.dtb \
 +	qcom-ipq4019-a62.dtb \
++	qcom-ipq4019-eap2200.dtb \
 +	qcom-ipq4019-fritzbox-7530.dtb \
 +	qcom-ipq4019-fritzrepeater-1200.dtb \
 +	qcom-ipq4019-fritzrepeater-3000.dtb \
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 11e775a5dc..da53220f09 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -36,10 +36,11 @@ Signed-off-by: John Crispin <john@phrozen.org>
  	qcom-ipq4019-ap.dk07.1-c1.dtb \
  	qcom-ipq4019-ap.dk07.1-c2.dtb \
 +	qcom-ipq4019-a62.dtb \
++	qcom-ipq4019-ea8300.dtb \
++	qcom-ipq4019-eap2200.dtb \
 +	qcom-ipq4019-fritzbox-7530.dtb \
 +	qcom-ipq4019-fritzrepeater-1200.dtb \
 +	qcom-ipq4019-fritzrepeater-3000.dtb \
-+	qcom-ipq4019-ea8300.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-e2600ac-c1.dtb \
 +	qcom-ipq4019-e2600ac-c2.dtb \