diff options
Diffstat (limited to 'package')
3 files changed, 745 insertions, 9 deletions
diff --git a/package/boot/uboot-kirkwood/Makefile b/package/boot/uboot-kirkwood/Makefile index 74b9f0fded..c42f947612 100644 --- a/package/boot/uboot-kirkwood/Makefile +++ b/package/boot/uboot-kirkwood/Makefile @@ -58,6 +58,10 @@ define uboot/iconnect_second_stage TITLE:=second stage U-Boot for Iomega iConnect Wireless endef +define uboot/nsa310 + TITLE:=U-Boot for Zyxel NSA310 +endef + define uboot/pogo_e02 TITLE:=U-Boot for Cloud Engines Pogoplug E02 endef @@ -75,6 +79,7 @@ UBOOTS:= \ goflexhome \ ib62x0 ib62x0_second_stage \ iconnect iconnect_second_stage \ + nsa310 \ pogo_e02 pogo_e02_second_stage \ sheevaplug diff --git a/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch b/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch new file mode 100644 index 0000000000..b9fb78d66d --- /dev/null +++ b/package/boot/uboot-kirkwood/patches/007-nsa310-uboot-generic.patch @@ -0,0 +1,722 @@ +arm: kirkwood: add ZyXEL NSA310 device + +This patch add ZyXEL NSA310 1-Bay Media Server + +The ZyXEL NSA310 device is a Kirkwood based NAS: + +- SoC: Marvell 88F6702 1200Mhz +- SDRAM memory: 256MB DDR2 400Mhz +- Gigabit ethernet: PHY Realtek +- Flash memory: 128MB +- 1 Power button +- 1 Power LED (blue) +- 5 Status LED (green/red) +- 1 Copy/Sync button +- 1 Reset button +- 2 SATA II port (1 internal and 1 external eSata) +- 2 USB 2.0 ports (1 front and 1 back) +- Smart fan + +Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> + +NOTE: this patch is ready for upstream, LEDE-specific parts are in + another patch + +diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig +index 9205b1e..819bd3b 100644 +--- a/arch/arm/mach-kirkwood/Kconfig ++++ b/arch/arm/mach-kirkwood/Kconfig +@@ -49,6 +49,9 @@ config TARGET_GOFLEXHOME + config TARGET_NAS220 + bool "BlackArmor NAS220" + ++config TARGET_NSA310 ++ bool "Zyxel NSA310 Board" ++ + config TARGET_NSA310S + bool "Zyxel NSA310S" + +@@ -72,6 +75,7 @@ source "board/raidsonic/ib62x0/Kconfig" + source "board/Seagate/dockstar/Kconfig" + source "board/Seagate/goflexhome/Kconfig" + source "board/Seagate/nas220/Kconfig" ++source "board/zyxel/nsa310/Kconfig" + source "board/zyxel/nsa310s/Kconfig" + + endif +diff --git a/board/zyxel/nsa310/Kconfig b/board/zyxel/nsa310/Kconfig +new file mode 100644 +index 0000000..145ade6 +--- /dev/null ++++ b/board/zyxel/nsa310/Kconfig +@@ -0,0 +1,12 @@ ++if TARGET_NSA310 ++ ++config SYS_BOARD ++ default "nsa310" ++ ++config SYS_VENDOR ++ default "zyxel" ++ ++config SYS_CONFIG_NAME ++ default "nsa310" ++ ++endif +diff --git a/board/zyxel/nsa310/MAINTAINERS b/board/zyxel/nsa310/MAINTAINERS +new file mode 100644 +index 0000000..d09f1ab +--- /dev/null ++++ b/board/zyxel/nsa310/MAINTAINERS +@@ -0,0 +1,6 @@ ++NSA310 BOARD ++M: Alberto Bursi <alberto.bursi@outlook.it> ++S: Maintained ++F: board/zyxel/nsa310/ ++F: include/configs/nsa310.h ++F: configs/nsa310_defconfig +diff --git a/board/zyxel/nsa310/Makefile b/board/zyxel/nsa310/Makefile +new file mode 100644 +index 0000000..dfe93cc +--- /dev/null ++++ b/board/zyxel/nsa310/Makefile +@@ -0,0 +1,12 @@ ++# ++# (C) Copyright 2015 bodhi <mibodhi@gmail.com> ++# ++# Based on ++# (C) Copyright 2009 ++# Marvell Semiconductor <www.marvell.com> ++# Written-by: Prafulla Wadaskar <prafulla@marvell.com> ++# ++# SPDX-License-Identifier: GPL-2.0+ ++# ++ ++obj-y := nsa310.o +diff --git a/board/zyxel/nsa310/kwbimage.cfg b/board/zyxel/nsa310/kwbimage.cfg +new file mode 100644 +index 0000000..f60e1d2 +--- /dev/null ++++ b/board/zyxel/nsa310/kwbimage.cfg +@@ -0,0 +1,166 @@ ++# ++# Copyright (C) 2013 Rafal Kazmierowski ++# ++# Based on guruplug.c originally written by ++# Siddarth Gore <gores@marvell.com> ++# (C) Copyright 2009 ++# Marvell Semiconductor <www.marvell.com> ++# ++# See file CREDITS for list of people who contributed to this ++# project. ++# ++# This program is free software; you can redistribute it and/or ++# modify it under the terms of the GNU General Public License as ++# published by the Free Software Foundation; either version 2 of ++# the License, or (at your option) any later version. ++# ++# This program is distributed in the hope that it will be useful, ++# but WITHOUT ANY WARRANTY; without even the implied warranty of ++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++# GNU General Public License for more details. ++# ++# You should have received a copy of the GNU General Public License ++# along with this program; if not, write to the Free Software ++# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, ++# MA 02110-1301 USA ++# ++# Refer docs/README.kwimage for more details about how-to configure ++# and create kirkwood boot image ++# ++ ++# Boot Media configurations ++BOOT_FROM nand ++#BOOT_FROM uart ++NAND_ECC_MODE default ++NAND_PAGE_SIZE 0x0800 ++ ++# SOC registers configuration using bootrom header extension ++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed ++ ++# Configure RGMII-0 interface pad voltage to 1.8V ++DATA 0xFFD100e0 0x1b1b1b9b ++ ++#Dram initalization for SINGLE x16 CL=5 @ 400MHz ++DATA 0xFFD01400 0x43010c30 # DDR Configuration register ++# bit13-0: 0xc30 (3120 DDR2 clks refresh rate) ++# bit23-14: zero ++# bit24: 1= enable exit self refresh mode on DDR access ++# bit25: 1 required ++# bit29-26: zero ++# bit31-30: 01 ++ ++DATA 0xFFD01404 0x37543000 # DDR Controller Control Low ++# bit 4: 0=addr/cmd in smame cycle ++# bit 5: 0=clk is driven during self refresh, we don't care for APX ++# bit 6: 0=use recommended falling edge of clk for addr/cmd ++# bit14: 0=input buffer always powered up ++# bit18: 1=cpu lock transaction enabled ++# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 ++# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM ++# bit30-28: 3 required ++# bit31: 0=no additional STARTBURST delay ++ ++DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) ++# bit3-0: TRAS lsbs ++# bit7-4: TRCD ++# bit11- 8: TRP ++# bit15-12: TWR ++# bit19-16: TWTR ++# bit20: TRAS msb ++# bit23-21: 0x0 ++# bit27-24: TRRD ++# bit31-28: TRTP ++ ++DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) ++# bit6-0: TRFC ++# bit8-7: TR2R ++# bit10-9: TR2W ++# bit12-11: TW2W ++# bit31-13: zero required ++ ++DATA 0xFFD01410 0x0000000c # DDR Address Control ++# bit1-0: 01, Cs0width=x8 ++# bit3-2: 10, Cs0size=1Gb ++# bit5-4: 01, Cs1width=x8 ++# bit7-6: 10, Cs1size=1Gb ++# bit9-8: 00, Cs2width=nonexistent ++# bit11-10: 00, Cs2size =nonexistent ++# bit13-12: 00, Cs3width=nonexistent ++# bit15-14: 00, Cs3size =nonexistent ++# bit16: 0, Cs0AddrSel ++# bit17: 0, Cs1AddrSel ++# bit18: 0, Cs2AddrSel ++# bit19: 0, Cs3AddrSel ++# bit31-20: 0 required ++ ++DATA 0xFFD01414 0x00000000 # DDR Open Pages Control ++# bit0: 0, OpenPage enabled ++# bit31-1: 0 required ++ ++DATA 0xFFD01418 0x00000000 # DDR Operation ++# bit3-0: 0x0, DDR cmd ++# bit31-4: 0 required ++ ++DATA 0xFFD0141C 0x00000652 # DDR Mode ++# bit2-0: 2, BurstLen=2 required ++# bit3: 0, BurstType=0 required ++# bit6-4: 4, CL=5 ++# bit7: 0, TestMode=0 normal ++# bit8: 0, DLL reset=0 normal ++# bit11-9: 6, auto-precharge write recovery ???????????? ++# bit12: 0, PD must be zero ++# bit31-13: 0 required ++ ++DATA 0xFFD01420 0x00000004 # DDR Extended Mode ++# bit0: 0, DDR DLL enabled ++# bit1: 0, DDR drive strenght normal ++# bit2: 0, DDR ODT control lsd (disabled) ++# bit5-3: 000, required ++# bit6: 1, DDR ODT control msb, (disabled) ++# bit9-7: 000, required ++# bit10: 0, differential DQS enabled ++# bit11: 0, required ++# bit12: 0, DDR output buffer enabled ++# bit31-13: 0 required ++ ++DATA 0xFFD01424 0x0000F17F # DDR Controller Control High ++# bit2-0: 111, required ++# bit3 : 1 , MBUS Burst Chop disabled ++# bit6-4: 111, required ++# bit7 : 0 ++# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz ++# bit9 : 0 , no half clock cycle addition to dataout ++# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals ++# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh ++# bit15-12: 1111 required ++# bit31-16: 0 required ++ ++DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) ++DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) ++ ++ ++DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size ++#DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 ++# bit0: 1, Window enabled ++# bit1: 0, Write Protect disabled ++# bit3-2: 00, CS0 hit selected ++# bit23-4: ones, required ++# bit31-24: 0x0F, Size (i.e. 256MB) ++ ++DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb ++DATA 0xFFD0150C 0x00000000 # CS[2]n Size, window disabled KAZ z 400db ++DATA 0xFFD01514 0x00000000 # CS[3]n Size, window disabled ++ ++DATA 0xFFD0151C 0x00000000 # DDR ODT Control (Low) ++DATA 0xFFD01494 0x00120012 # DDR ODT Control (High) KAZ z nowy STATIC_SDRAM_ODT_CTRL_LOW ++# bit1-0: 00, ODT0 controlled by ODT Control (low) register above ++# bit3-2: 01, ODT1 active NEVER! ++# bit31-4: zero, required ++ ++DATA 0xFFD01498 0x00000000 # CPU ODT Control KAZ STATIC_SDRAM_ODT_CTRL_HI ++DATA 0xFFD0149C 0x0000E403 # DDR Initialization Control KAZ STATIC_SDRAM_DUNIT_ODT_CTRL ++DATA 0xFFD01480 0x00000001 # DDR Initialization Control ++#bit0=1, enable DDR init upon this register write ++ ++# End of Header extension ++DATA 0x0 0x0 +diff --git a/board/zyxel/nsa310/nsa310.c b/board/zyxel/nsa310/nsa310.c +new file mode 100644 +index 0000000..eee3f1a +--- /dev/null ++++ b/board/zyxel/nsa310/nsa310.c +@@ -0,0 +1,190 @@ ++/* ++ * Copyright (C) 2013 Rafal Kazmierowski ++ * ++ * Based on NSA320.c Peter Schildmann <linux@schildmann.info> ++ * originally written by ++ * Marvell Semiconductor <www.marvell.com> ++ * Written-by: Prafulla Wadaskar <prafulla@marvell.com> ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, ++ * MA 02110-1301 USA ++ */ ++ ++#include <common.h> ++#include <miiphy.h> ++#include <asm/arch/cpu.h> ++#include <asm/arch/soc.h> ++#include <asm/arch/mpp.h> ++#include <asm/io.h> ++#include "nsa310.h" ++ ++DECLARE_GLOBAL_DATA_PTR; ++ ++int board_early_init_f(void) ++{ ++ /* ++ * default gpio configuration ++ * There are maximum 64 gpios controlled through 2 sets of registers ++ * the below configuration configures mainly initial LED status ++ */ ++ mvebu_config_gpio(NSA310_VAL_LOW, NSA310_VAL_HIGH, ++ NSA310_OE_LOW, NSA310_OE_HIGH); ++ ++ /* Multi-Purpose Pins Functionality configuration */ ++ /* (all LEDs & power off active high) */ ++ static const u32 kwmpp_config[] = { ++ MPP0_NF_IO2, ++ MPP1_NF_IO3, ++ MPP2_NF_IO4, ++ MPP3_NF_IO5, ++ MPP4_NF_IO6, ++ MPP5_NF_IO7, ++ MPP6_SYSRST_OUTn, ++ MPP7_GPO, ++ MPP8_TW_SDA, /* PCF8563 RTC chip */ ++ MPP9_TW_SCK, /* connected to TWSI */ ++ MPP10_UART0_TXD, ++ MPP11_UART0_RXD, ++ MPP12_GPO, /* SATA2 LED (green) */ ++ MPP13_GPIO, /* SATA2 LED (red) */ ++ MPP14_GPIO, /* MCU DATA pin (in) */ ++ MPP15_GPIO, /* USB LED (green) */ ++ MPP16_GPIO, /* MCU CLK pin (out) */ ++ MPP17_GPIO, /* MCU ACT pin (out) */ ++ MPP18_NF_IO0, ++ MPP19_NF_IO1, ++ MPP20_GPIO, ++ MPP21_GPIO, /* USB LED (red)-Power*/ ++ MPP22_GPIO, ++ MPP23_GPIO, ++ MPP24_GPIO, ++ MPP25_GPIO, ++ MPP26_GPIO, ++ MPP27_GPIO, ++ MPP28_GPIO, /* SYS LED (green) */ ++ MPP29_GPIO, /* SYS LED (red) */ ++ MPP30_GPIO, ++ MPP31_GPIO, ++ MPP32_GPIO, ++ MPP33_GPIO, ++ MPP34_GPIO, ++ MPP35_GPIO, ++ MPP36_GPIO, /* Reset button */ ++ MPP37_GPIO, /* Copy button */ ++ MPP38_GPIO, /* VID B0 */ ++ MPP39_GPIO, /* COPY LED (green) */ ++ MPP40_GPIO, /* COPY LED (red) */ ++ MPP41_GPIO, /* SATA1 LED (green) */ ++ MPP42_GPIO, /* SATA1 LED (red) */ ++ MPP43_GPIO, /* HTP pin */ ++ MPP44_GPIO, /* Buzzer */ ++ MPP45_GPIO, /* VID B1 */ ++ MPP46_GPIO, /* Power button */ ++ MPP47_GPIO, /* Power resume data */ ++ MPP48_GPIO, /* Power off */ ++ MPP49_GPIO, /* Power resume clock */ ++ 0 ++ }; ++ kirkwood_mpp_conf(kwmpp_config,NULL); ++ return 0; ++} ++ ++int board_init(void) ++{ ++ /* address of boot parameters */ ++ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; ++ ++ return 0; ++} ++ ++#ifdef CONFIG_RESET_PHY_R ++/* Configure and enable MV88E1318 PHY */ ++void reset_phy(void) ++{ ++ u16 reg; ++ u16 devadr; ++ char *name = "egiga0"; ++ ++ if (miiphy_set_current_dev(name)) ++ return; ++ ++ /* command to read PHY dev address */ ++ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { ++ printf("Err..%s could not read PHY dev address\n", ++ __FUNCTION__); ++ return; ++ } ++ ++ /* Set RGMII delay */ ++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 2); ++ miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, ®); ++ reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL); ++ miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg); ++ miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0); ++ ++ /* reset the phy */ ++ miiphy_reset(name, devadr); ++ ++ printf("MV88E1318 PHY initialized on %s\n", name); ++} ++#endif /* CONFIG_RESET_PHY_R */ ++ ++#ifdef CONFIG_SHOW_BOOT_PROGRESS ++void show_boot_progress(int val) ++{ ++ struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE; ++ u32 dout0 = readl(&gpio0->dout); ++ u32 blen0 = readl(&gpio0->blink_en); ++ ++ struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE; ++ u32 dout1 = readl(&gpio1->dout); ++ u32 blen1 = readl(&gpio1->blink_en); ++ ++ switch (val) { ++ case BOOTSTAGE_ID_DECOMP_IMAGE: ++ writel(blen0 & ~(SYS_GREEN_LED | SYS_RED_LED), &gpio0->blink_en); ++ writel((dout0 & ~SYS_GREEN_LED) | SYS_RED_LED, &gpio0->dout); ++ break; ++ case BOOTSTAGE_ID_RUN_OS: ++ writel(dout0 & ~SYS_RED_LED, &gpio0->dout); ++ writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en); ++ break; ++ case BOOTSTAGE_ID_NET_START: ++ writel(dout1 & ~COPY_RED_LED, &gpio1->dout); ++ writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en); ++ break; ++ case BOOTSTAGE_ID_NET_LOADED: ++ writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en); ++ writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout); ++ break; ++ case -BOOTSTAGE_ID_NET_NETLOOP_OK: ++ case -BOOTSTAGE_ID_NET_LOADED: ++ writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout); ++ writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en); ++ break; ++ default: ++ if (val < 0) { ++ /* error */ ++ printf("Error occured, error code = %d\n", -val); ++ writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout); ++ writel(blen0 | SYS_RED_LED, &gpio0->blink_en); ++ } ++ break; ++ } ++} ++#endif +diff --git a/board/zyxel/nsa310/nsa310.h b/board/zyxel/nsa310/nsa310.h +new file mode 100644 +index 0000000..6634a4f +--- /dev/null ++++ b/board/zyxel/nsa310/nsa310.h +@@ -0,0 +1,56 @@ ++/* ++ * Copyright (C) 2013 Rafal Kazmierowski ++ * ++ * Based on Peter Schildmann <linux@schildmann.info> ++ * and guruplug.h originally written by ++ * Siddarth Gore <gores@marvell.com> ++ * (C) Copyright 2009 ++ * Marvell Semiconductor <www.marvell.com> ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, ++ * MA 02110-1301 USA ++ */ ++ ++#ifndef __NSA310_H ++#define __NSA310_H ++ ++/* GPIO's */ ++#define SYS_GREEN_LED (1 << 28) ++#define SYS_RED_LED (1 << 29) ++#define SATA1_GREEN_LED (1 << 41) ++#define SATA1_RED_LED (1 << 42) ++#define SATA2_GREEN_LED (1 << 12) ++#define SATA2_RED_LED (1 << 13) ++#define USB_GREEN_LED (1 << 15) ++#define USB_RED_LED (1 << 21) ++#define COPY_GREEN_LED (1 << 39) ++#define COPY_RED_LED (1 << 40) ++ ++#define NSA310_OE_LOW (0) ++#define NSA310_VAL_LOW (SYS_GREEN_LED) ++#define NSA310_OE_HIGH ((COPY_GREEN_LED | COPY_RED_LED | \ ++ SATA1_GREEN_LED | SATA1_RED_LED)) ++#define NSA310_VAL_HIGH (0) ++ ++/* PHY related */ ++#define MV88E1318_MAC_CTRL_REG 21 ++#define MV88E1318_PGADR_REG 22 ++#define MV88E1318_RGMII_TXTM_CTRL (1 << 4) ++#define MV88E1318_RGMII_RXTM_CTRL (1 << 5) ++ ++#endif /* __NSA310_H */ +diff --git a/configs/nsa310_defconfig b/configs/nsa310_defconfig +new file mode 100644 +index 0000000..d26ef35 +--- /dev/null ++++ b/configs/nsa310_defconfig +@@ -0,0 +1,18 @@ ++CONFIG_ARM=y ++CONFIG_KIRKWOOD=y ++CONFIG_TARGET_NSA310=y ++CONFIG_BOOTDELAY=3 ++CONFIG_SYS_PROMPT="NSA310> " ++# CONFIG_CMD_IMLS is not set ++# CONFIG_CMD_FLASH is not set ++CONFIG_SYS_NS16550=y ++CONFIG_CMD_FDT=y ++CONFIG_OF_LIBFDT=y ++CONFIG_CMD_SETEXPR=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_NAND=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_USB=y ++CONFIG_CMD_EXT2=y ++CONFIG_CMD_FAT=y ++CONFIG_USB_STORAGE=y +diff --git a/include/configs/nsa310.h b/include/configs/nsa310.h +new file mode 100644 +index 0000000..86ef825 +--- /dev/null ++++ b/include/configs/nsa310.h +@@ -0,0 +1,168 @@ ++/* Copyright (C) 2015-2016 bodhi <mibodhi@gmail.com> ++ * ++ * Based on ++ * Copyright (C) 2012 Peter Schildmann <linux@schildmann.info> ++ * ++ * Based on guruplug.h originally written by ++ * Siddarth Gore <gores@marvell.com> ++ * (C) Copyright 2009 ++ * Marvell Semiconductor <www.marvell.com> ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, ++ * MA 02110-1301 USA ++ */ ++ ++#ifndef _CONFIG_NSA310_H ++#define _CONFIG_NSA310_H ++ ++/* ++ * Version number information ++ */ ++ ++#define CONFIG_IDENT_STRING "\nZyXEL NSA310 1-Bay Power Media Server \n" ++ ++/* ++ * High Level Configuration Options (easy to change) ++ */ ++#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */ ++#define CONFIG_KW88F6281 /* SOC Name */ ++#define CONFIG_MACH_NSA310 /* Machine type */ ++#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ ++ ++/* ++ * Misc Configuration Options ++ */ ++#define CONFIG_SHOW_BOOT_PROGRESS 1 /* boot progess display (LED's) */ ++ ++/* ++ * Commands configuration ++ */ ++#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ ++#define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */ ++#define CONFIG_CMD_DHCP ++#define CONFIG_CMD_ENV ++#define CONFIG_CMD_IDE ++#define CONFIG_CMD_MII ++#define CONFIG_CMD_NAND ++#define CONFIG_CMD_PING ++#define CONFIG_CMD_USB ++#define CONFIG_CMD_DATE ++#define CONFIG_SYS_LONGHELP ++#define CONFIG_PREBOOT ++#define CONFIG_SYS_HUSH_PARSER ++#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " ++ ++/* ++ * mv-common.h should be defined after CMD configs since it used them ++ * to enable certain macros ++ */ ++#include "mv-common.h" ++ ++/* Remove or override few declarations from mv-common.h */ ++#undef CONFIG_SYS_PROMPT /* previously defined in mv-common.h */ ++#define CONFIG_SYS_PROMPT "NSA310> " /* Command Prompt */ ++ ++/* ++ * Environment variables configurations ++ */ ++#ifdef CONFIG_CMD_NAND ++#define CONFIG_ENV_IS_IN_NAND 1 ++#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ ++#else ++#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */ ++#endif ++ ++/* max 4k env size is enough, but in case of nand ++ * it has to be rounded to sector size ++ */ ++#define CONFIG_ENV_SIZE 0x20000 /* 128k */ ++#define CONFIG_ENV_ADDR 0xc0000 ++#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here */ ++ ++/* ++ * Default environment variables ++ */ ++#define CONFIG_BOOTCOMMAND \ ++ "ubi part ubi; " \ ++ "ubi read 0x800000 kernel; " \ ++ "bootm 0x800000" ++ ++#define CONFIG_MTDPARTS \ ++ "mtdparts=orion_nand:" \ ++ "0x0c0000(uboot)," \ ++ "0x80000(uboot_env)," \ ++ "0x7ec0000(ubi)\0" ++ ++#define CONFIG_EXTRA_ENV_SETTINGS \ ++ "console=console=ttyS0,115200\0" \ ++ "mtdids=nand0=orion_nand\0" \ ++ "mtdparts="CONFIG_MTDPARTS \ ++ "bootargs_root=\0" ++ ++/* ++ * Ethernet Driver configuration ++ */ ++#ifdef CONFIG_CMD_NET ++#define CONFIG_NETCONSOLE ++#define CONFIG_NET_MULTI ++#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ ++#define CONFIG_PHY_BASE_ADR 0x1 ++#define CONFIG_PHY_GIGE ++#define CONFIG_RESET_PHY_R ++#endif /* CONFIG_CMD_NET */ ++ ++/* ++ * SATA Driver configuration ++ */ ++#ifdef CONFIG_MVSATA_IDE ++#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET ++#define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET ++#endif /* CONFIG_MVSATA_IDE */ ++ ++/* ++ * File system ++ */ ++#define CONFIG_CMD_EXT2 ++#define CONFIG_CMD_EXT4 ++#define CONFIG_CMD_FAT ++#define CONFIG_CMD_JFFS2 ++#define CONFIG_JFFS2_NAND ++#define CONFIG_JFFS2_LZO ++#define CONFIG_CMD_UBI ++#define CONFIG_CMD_UBIFS ++#define CONFIG_RBTREE ++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ ++#define CONFIG_MTD_PARTITIONS ++#define CONFIG_CMD_MTDPARTS ++#define CONFIG_LZO ++ ++/* ++ * EFI partition ++ */ ++#define CONFIG_EFI_PARTITION ++ ++/* ++ * Date Time ++ */ ++#ifdef CONFIG_CMD_DATE ++#define CONFIG_RTC_MV ++#define CONFIG_CMD_SNTP ++#define CONFIG_CMD_DNS ++#endif /* CONFIG_CMD_DATE */ ++ ++#endif /* _CONFIG_NSA310_H */ diff --git a/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch b/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch index 37f30d0a50..1f5dd84107 100644 --- a/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch +++ b/package/boot/uboot-kirkwood/patches/200-openwrt-config.patch @@ -1,9 +1,9 @@ --- a/arch/arm/mach-kirkwood/Kconfig +++ b/arch/arm/mach-kirkwood/Kconfig -@@ -74,4 +74,7 @@ source "board/Seagate/goflexhome/Kconfig - source "board/Seagate/nas220/Kconfig" +@@ -78,4 +78,7 @@ source "board/Seagate/nas220/Kconfig" + source "board/zyxel/nsa310/Kconfig" source "board/zyxel/nsa310s/Kconfig" - + +config SECOND_STAGE + bool "OpenWrt second stage hack" + @@ -13,7 +13,7 @@ @@ -98,4 +98,6 @@ #define CONFIG_CMD_MTDPARTS #define CONFIG_LZO - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_DOCKSTAR_H */ @@ -22,7 +22,7 @@ @@ -108,4 +108,6 @@ #define CONFIG_RTC_MV #endif /* CONFIG_CMD_DATE */ - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_IB62x0_H */ @@ -31,7 +31,7 @@ @@ -103,4 +103,6 @@ #define CONFIG_MTD_PARTITIONS #define CONFIG_CMD_MTDPARTS - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_ICONNECT_H */ @@ -83,7 +83,7 @@ @@ -99,4 +99,6 @@ #define CONFIG_CMD_MTDPARTS #define CONFIG_LZO - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_POGO_E02_H */ @@ -92,7 +92,7 @@ @@ -109,4 +109,6 @@ #define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET #endif /* CONFIG_CMD_IDE */ - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_SHEEVAPLUG_H */ @@ -101,7 +101,16 @@ @@ -122,4 +122,6 @@ #define CONFIG_RTC_MV #endif /* CONFIG_CMD_DATE */ - + +#include "openwrt-kirkwood-common.h" + #endif /* _CONFIG_GOFLEXHOME_H */ +--- a/include/configs/nsa310.h ++++ b/include/configs/nsa310.h +@@ -166,4 +166,6 @@ + #define CONFIG_CMD_DNS + #endif /* CONFIG_CMD_DATE */ + ++#include "openwrt-kirkwood-common.h" ++ + #endif /* _CONFIG_NSA310_H */ |