diff options
Diffstat (limited to 'target/linux/ath79')
4 files changed, 169 insertions, 0 deletions
diff --git a/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts b/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts new file mode 100644 index 0000000000..26bb906910 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_deco-m4r-v1.dts @@ -0,0 +1,147 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +#include "qca956x.dtsi" + +/ { + compatible = "tplink,deco-m4r-v1", "qca,qca9563"; + model = "TP-Link Deco M4R v1"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + wlan2g { + label = "red:wlan2g"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_power: power { + label = "green:power"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan5g { + label = "blue:wlan5g"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + phy-mask = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + qca,mib-poll-interval = <500>; + + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x080000>; + read-only; + }; + + partition@80000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x080000 0xe00000>; + }; + + partition@e80000 { + label = "product-info"; + reg = <0xe80000 0x05000>; + read-only; + }; + + config: partition@e85000 { + label = "config"; + reg = <0xe85000 0x16b000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "sgmii"; + phy-handle = <&phy0>; + + nvmem-cells = <&macaddr_config_8>; + nvmem-cell-names = "mac-address"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + nvmem-cells = <&macaddr_config_8>; + nvmem-cell-names = "mac-address"; +}; + +&config { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_config_8: macaddr@8 { + reg = <0x8 0x6>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index c84db5676f..38898ec6dc 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -508,6 +508,10 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" ;; + tplink,deco-m4r-v1) + ucidef_add_switch "switch0" \ + "0@eth0" "3:lan:1" "5:lan:2" + ;; xiaomi,mi-router-4q|\ zbtlink,zbt-wd323) ucidef_set_interface_wan "eth1" diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 00aa34f0a8..668fd76af3 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -269,6 +269,12 @@ case "$FIRMWARE" in ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ /lib/firmware/ath10k/QCA9984/hw1.0/board.bin ;; + tplink,deco-m4r-v1) + caldata_extract "art" 0x5000 0x2f20 + ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x8) -1) + ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ + /lib/firmware/ath10k/QCA9888/hw2.0/board.bin + ;; yuncore,a782|\ yuncore,xd4200) caldata_extract "art" 0x5000 0x2f20 diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 6479f6e26a..fed572c884 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -456,6 +456,18 @@ define Device/tplink_eap245-v3 endef TARGET_DEVICES += tplink_eap245-v3 +define Device/tplink_deco-m4r-v1 + $(Device/tplink-safeloader-uimage) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := Deco M4R + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + SUPPORTED_DEVICES += deco-m4r-v1 + TPLINK_BOARD_ID := DECO-M4R-V1 +endef +TARGET_DEVICES += tplink_deco-m4r-v1 + define Device/tplink_re350k-v1 $(Device/tplink-safeloader) SOC := qca9558 |