diff options
Diffstat (limited to 'target/linux/ipq40xx')
11 files changed, 847 insertions, 11 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index d8a5697361..6a7b09cc60 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -29,7 +29,8 @@ ipq40xx_setup_interfaces() "0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; avm,fritzbox-4040|\ - linksys,ea6350v3) + linksys,ea6350v3|\ + linksys,ea8300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index af84e4e84a..1e64b93a46 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -93,7 +93,6 @@ ath10kcal_is_caldata_valid() { board=$(board_name) - case "$FIRMWARE" in "ath10k/cal-pci-0000:01:00.0.bin") case "$board" in @@ -115,6 +114,11 @@ case "$FIRMWARE" in /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader0") || \ /usr/bin/fritz_cal_extract -i 1 -s 0x3D000 -e 0x212 -l 12064 -o /lib/firmware/$FIRMWARE $(find_mtd_chardev "urlader1") ;; + linksys,ea8300) + ath10kcal_extract "ART" 36864 12064 + # OEM assigns 4 sequential MACs + ath10kcal_patch_mac_crc $(macaddr_setbit_la $(macaddr_add "$(cat /sys/class/net/eth0/address)" 4)) + ;; openmesh,a62) ath10kcal_extract "0:ART" 36864 12064 ;; @@ -156,6 +160,10 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 4096 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +2) ;; + linksys,ea8300) + ath10kcal_extract "ART" 4096 12064 + ath10kcal_patch_mac_crc $(macaddr_add "$(cat /sys/class/net/eth0/address)" 2) + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 4096 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 4096 12064 @@ -209,6 +217,10 @@ case "$FIRMWARE" in ath10kcal_extract "ART" 20480 12064 ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +3) ;; + linksys,ea8300) + ath10kcal_extract "ART" 20480 12064 + ath10kcal_patch_mac_crc $(macaddr_add "$(cat /sys/class/net/eth0/address)" 3) + ;; meraki,mr33) ath10kcal_ubi_extract "ART" 20480 12064 ath10kcal_is_caldata_valid "202f" || ath10kcal_extract "ART" 20480 12064 diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount index abde12412a..f2d76f125f 100755 --- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -10,7 +10,8 @@ start() { [ -n "$(fw_printenv bootcount changed 2>/dev/null)" ] &&\ echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s - ;; - linksys,ea6350v3) + linksys,ea6350v3|\ + linksys,ea8300) mtd resetbc s_env || true ;; esac diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh index ce5c1fc4bf..fc64441e1a 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh @@ -9,6 +9,11 @@ preinit_set_mac_address() { ip link set dev eth0 address $(macaddr_add "$base_mac" +1) ip link set dev eth1 address $(macaddr_add "$base_mac" +3) ;; + linksys,ea8300) + base_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr) + ip link set dev eth0 address "${base_mac}" + ip link set dev eth1 address $(macaddr_add "${base_mac}" 1) + ;; meraki,mr33) mac_lan=$(get_mac_binary "/sys/bus/i2c/devices/0-0050/eeprom" 102) [ -n "$mac_lan" ] && ip link set dev eth0 address "$mac_lan" diff --git a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh index 578ddbe4c4..be4b6322cb 100644 --- a/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh +++ b/target/linux/ipq40xx/base-files/lib/preinit/06_set_preinit_iface_ipq40xx.sh @@ -7,6 +7,7 @@ set_preinit_iface() { asus,rt-ac58u| \ avm,fritzbox-4040| \ glinet,gl-b1300| \ + linksys,ea8300| \ meraki,mr33| \ zyxel,nbg6617) ifname=eth0 diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 84b123335c..e62d16c449 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -49,7 +49,7 @@ platform_do_upgrade() { 8dev,jalapeno |\ alfa-network,ap120c-ac |\ avm,fritzbox-7530 |\ - avm,fritzrepeater-3000|\ + avm,fritzrepeater-3000 |\ qxwlan,e2600ac-c2) nand_do_upgrade "$ARGV" ;; @@ -62,18 +62,19 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; - linksys,ea6350v3) + linksys,ea6350v3 |\ + linksys,ea8300) platform_do_upgrade_linksys "$ARGV" ;; + meraki,mr33) + CI_KERNPART="part.safe" + nand_do_upgrade "$1" + ;; openmesh,a42 |\ openmesh,a62) PART_NAME="inactive" platform_do_upgrade_openmesh "$ARGV" ;; - meraki,mr33) - CI_KERNPART="part.safe" - nand_do_upgrade "$1" - ;; zyxel,nbg6617) zyxel_do_upgrade "$1" ;; diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts new file mode 100644 index 0000000000..cfc3037fb2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts @@ -0,0 +1,399 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/* + * Device Tree Source for Linksys EA8300 (Dallas) + * + * Copyright (C) 2019 Jeff Kletsky + * + */ + +/dts-v1/; + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "Linksys EA8300 (Dallas)"; + compatible = "linksys,ea8300", "qcom,ipq4019"; + + + aliases { + led-boot = &led_wps_amber; + led-failsafe = &led_wps; + led-running = &led_linksys; + led-upgrade = &led_world; + serial0 = &blsp1_uart1; + }; + + + leds { + compatible = "gpio-leds"; + + // Retain node names from running OEM on EA8300 + + // Front panel LEDs, top to bottom + + led_plug: diag { + label = "ea8300:amber:plug"; + gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; + }; + + led_world: internet { + label = "ea8300:amber:world"; + gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + }; + + led_wps: wps { + label = "ea8300:white:wps"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + }; + + led_wps_amber: wps_amber { + label = "ea8300:amber:wps"; + gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_linksys: pwr { + label = "ea8300:white:linksys"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + // On back panel, above USB socket + + led_usb: usb { + label = "ea8300:green:usb"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb3_port1>, <&usb3_port2>, + <&usb2_port1>; + linux,default-trigger = "usbport"; + }; + }; + + + keys { + compatible = "gpio-keys"; + + button@0 { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + button@1 { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + }; + }; + + + // + // OEM U-Boot provides either + // init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \ + // root=ubi0:ubifs rootwait rw + // or the same with ubi.mtd=13,2048 + // + + chosen { + bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + +}; + +&cryptobam { + status = "okay"; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "qsee"; + reg = <0x200000 0x100000>; + read-only; + }; + + partition@300000 { + label = "cdt"; + reg = <0x300000 0x80000>; + read-only; + }; + + partition@380000 { + label = "appsblenv"; + reg = <0x380000 0x80000>; + read-only; + }; + + partition@400000 { + label = "ART"; + reg = <0x400000 0x80000>; + read-only; + }; + + partition@480000 { + label = "appsbl"; + reg = <0x480000 0x200000>; + read-only; + }; + + partition@680000 { + label = "u_env"; + reg = <0x680000 0x80000>; + // writable -- U-Boot environment + }; + + partition@700000 { + label = "s_env"; + reg = <0x700000 0x40000>; + // writable -- Boot counter records + }; + + partition@740000 { + label = "devinfo"; + reg = <0x740000 0x40000>; + read-only; + }; + + partition@780000 { + label = "kernel"; + reg = <0x780000 0x5800000>; + }; + + partition@a80000 { + label = "rootfs"; + reg = <0xa80000 0x5500000>; + }; + + partition@5f80000 { + label = "alt_kernel"; + reg = <0x5f80000 0x5800000>; + }; + + partition@6280000 { + label = "alt_rootfs"; + reg = <0x6280000 0x5500000>; + }; + + partition@b780000 { + label = "sysdiag"; + reg = <0xb780000 0x100000>; + read-only; + }; + + partition@b880000 { + label = "syscfg"; + reg = <0xb880000 0x4680000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + // gpio61 controls led_usb + + pulldowns { + pins = "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi1 { + status = "okay"; + ieee80211-freq-limit = <5170000 5330000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi2 { + status = "okay"; + ieee80211-freq-limit = <5490000 5835000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts new file mode 100644 index 0000000000..cfc3037fb2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-linksys_ea8300.dts @@ -0,0 +1,399 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/* + * Device Tree Source for Linksys EA8300 (Dallas) + * + * Copyright (C) 2019 Jeff Kletsky + * + */ + +/dts-v1/; + +#include "qcom-ipq4019.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/soc/qcom,tcsr.h> + +/ { + model = "Linksys EA8300 (Dallas)"; + compatible = "linksys,ea8300", "qcom,ipq4019"; + + + aliases { + led-boot = &led_wps_amber; + led-failsafe = &led_wps; + led-running = &led_linksys; + led-upgrade = &led_world; + serial0 = &blsp1_uart1; + }; + + + leds { + compatible = "gpio-leds"; + + // Retain node names from running OEM on EA8300 + + // Front panel LEDs, top to bottom + + led_plug: diag { + label = "ea8300:amber:plug"; + gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>; + }; + + led_world: internet { + label = "ea8300:amber:world"; + gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + }; + + led_wps: wps { + label = "ea8300:white:wps"; + gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>; + }; + + led_wps_amber: wps_amber { + label = "ea8300:amber:wps"; + gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + + led_linksys: pwr { + label = "ea8300:white:linksys"; + gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>; + }; + + // On back panel, above USB socket + + led_usb: usb { + label = "ea8300:green:usb"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + trigger-sources = <&usb3_port1>, <&usb3_port2>, + <&usb2_port1>; + linux,default-trigger = "usbport"; + }; + }; + + + keys { + compatible = "gpio-keys"; + + button@0 { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + }; + + button@1 { + label = "wps"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + }; + }; + + + // + // OEM U-Boot provides either + // init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \ + // root=ubi0:ubifs rootwait rw + // or the same with ubi.mtd=13,2048 + // + + chosen { + bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro"; + }; + + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = <TCSR_ESS_PSGMII>; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>; + }; + + usb2@60f8800 { + status = "okay"; + + dwc3@6000000 { + #address-cells = <1>; + #size-cells = <0>; + + usb2_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + }; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + #address-cells = <1>; + #size-cells = <0>; + + usb3_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + usb3_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + + +&blsp_dma { + status = "okay"; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + +}; + +&cryptobam { + status = "okay"; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "sbl1"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "mibib"; + reg = <0x100000 0x100000>; + read-only; + }; + + partition@200000 { + label = "qsee"; + reg = <0x200000 0x100000>; + read-only; + }; + + partition@300000 { + label = "cdt"; + reg = <0x300000 0x80000>; + read-only; + }; + + partition@380000 { + label = "appsblenv"; + reg = <0x380000 0x80000>; + read-only; + }; + + partition@400000 { + label = "ART"; + reg = <0x400000 0x80000>; + read-only; + }; + + partition@480000 { + label = "appsbl"; + reg = <0x480000 0x200000>; + read-only; + }; + + partition@680000 { + label = "u_env"; + reg = <0x680000 0x80000>; + // writable -- U-Boot environment + }; + + partition@700000 { + label = "s_env"; + reg = <0x700000 0x40000>; + // writable -- Boot counter records + }; + + partition@740000 { + label = "devinfo"; + reg = <0x740000 0x40000>; + read-only; + }; + + partition@780000 { + label = "kernel"; + reg = <0x780000 0x5800000>; + }; + + partition@a80000 { + label = "rootfs"; + reg = <0xa80000 0x5500000>; + }; + + partition@5f80000 { + label = "alt_kernel"; + reg = <0x5f80000 0x5800000>; + }; + + partition@6280000 { + label = "alt_rootfs"; + reg = <0x6280000 0x5500000>; + }; + + partition@b780000 { + label = "sysdiag"; + reg = <0xb780000 0x100000>; + read-only; + }; + + partition@b880000 { + label = "syscfg"; + reg = <0xb880000 0x4680000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&tlmm { + serial_0_pins: serial0-pinmux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + // gpio61 controls led_usb + + pulldowns { + pins = "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", + "gpio64", "gpio65", "gpio66", + "gpio67", "gpio68", "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi1 { + status = "okay"; + ieee80211-freq-limit = <5170000 5330000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; + +&wifi2 { + status = "okay"; + ieee80211-freq-limit = <5490000 5835000>; + qcom,ath10k-calibration-variant = "linksys-ea8300-fcc"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index ae146cdc54..3a9b58de4f 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -248,6 +248,21 @@ define Device/linksys_ea6350v3 endef TARGET_DEVICES += linksys_ea6350v3 +define Device/linksys_ea8300 + $(call Device/FitzImage) + DEVICE_TITLE := Linksys EA8300 (Dallas) + DEVICE_DTS := qcom-ipq4019-linksys_ea8300 + KERNEL_SIZE := 3072k + IMAGE_SIZE := 87040k + BLOCKSIZE := 128k + PAGESIZE := 2048 + UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF + IMAGES := sysupgrade.bin factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA8300 + DEVICE_PACKAGES := uboot-envtools ath10k-firmware-qca9888-ct ipq-wifi-linksys_ea8300 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += linksys_ea8300 + define Device/meraki_mr33 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4029-mr33 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 6743f44b25..bb539155e9 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,29 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,30 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-ap.dk04.1-c1.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzrepeater-3000.dtb \ ++ qcom-ipq4019-linksys_ea8300.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index 57a5760806..a0386f6b66 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,32 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,33 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -34,6 +34,7 @@ Signed-off-by: John Crispin <john@phrozen.org> + qcom-ipq4019-a62.dtb \ + qcom-ipq4019-fritzbox-7530.dtb \ + qcom-ipq4019-fritzrepeater-3000.dtb \ ++ qcom-ipq4019-linksys_ea8300.dtb \ + qcom-ipq4019-map-ac2200.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c1.dtb \ + qcom-ipq4019-qxwlan-e2600ac-c2.dtb \ |