aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
diff options
context:
space:
mode:
Diffstat (limited to 'target/linux/ipq806x')
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/01_leds4
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/board.d/02_network5
-rw-r--r--target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata10
-rwxr-xr-xtarget/linux/ipq806x/base-files/etc/init.d/bootcount3
-rw-r--r--target/linux/ipq806x/base-files/lib/upgrade/platform.sh11
-rw-r--r--target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts400
-rw-r--r--target/linux/ipq806x/image/Makefile12
-rw-r--r--target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch3
8 files changed, 447 insertions, 1 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds
index f8b6c32358..ffefb9e01c 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/01_leds
+++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds
@@ -19,6 +19,10 @@ compex,wpq864)
ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1"
ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1"
;;
+edgecore,ecw5410)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy1tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy0tpt"
+ ;;
nec,wg2600hp)
ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy1tpt"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy0tpt"
diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network
index 529a8d9f39..0dbc49840a 100755
--- a/target/linux/ipq806x/base-files/etc/board.d/02_network
+++ b/target/linux/ipq806x/base-files/etc/board.d/02_network
@@ -22,6 +22,11 @@ tplink,vr2600v)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
;;
+edgecore,ecw5410)
+ ucidef_set_interfaces_lan_wan "eth1" "eth0"
+ ucidef_set_interface_macaddr "lan" "$(mtd_get_mac_binary "0:ART" 0x6)"
+ ucidef_set_interface_macaddr "wan" "$(mtd_get_mac_binary "0:ART" 0x0)"
+ ;;
qcom,ipq8064-ap161)
ucidef_set_interface_lan "eth1 eth2"
ucidef_add_switch "switch0" \
diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8b4942dee1..f4572d038c 100644
--- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -13,6 +13,9 @@ case "$FIRMWARE" in
caldata_extract "ART" 0x1000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary ART 0x1e)
;;
+ edgecore,ecw5410)
+ ath10kcal_extract "0:ART" 4096 12064
+ ;;
linksys,ea7500-v1 |\
linksys,ea8500)
caldata_extract "art" 0x1000 0x2f20
@@ -77,6 +80,13 @@ case "$FIRMWARE" in
;;
esac
;;
+"ath10k/pre-cal-pci-0002:01:00.0.bin")
+ case $board in
+ edgecore,ecw5410)
+ ath10kcal_extract "0:ART" 20480 12064
+ ;;
+ esac
+ ;;
*)
exit 1
;;
diff --git a/target/linux/ipq806x/base-files/etc/init.d/bootcount b/target/linux/ipq806x/base-files/etc/init.d/bootcount
index 6e57c72e51..77965e647b 100755
--- a/target/linux/ipq806x/base-files/etc/init.d/bootcount
+++ b/target/linux/ipq806x/base-files/etc/init.d/bootcount
@@ -4,6 +4,9 @@ START=99
boot() {
case $(board_name) in
+ edgecore,ecw5410)
+ fw_setenv bootcount 0
+ ;;
linksys,ea7500-v1 |\
linksys,ea8500)
mtd resetbc s_env || true
diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
index 560e64af3a..91cc4548f5 100644
--- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
@@ -27,6 +27,17 @@ platform_do_upgrade() {
zyxel,nbg6817)
zyxel_do_upgrade "$1"
;;
+ edgecore,ecw5410)
+ part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')"
+ if [ "$part" = "rootfs1" ]; then
+ fw_setenv active 2 || exit 1
+ CI_UBIPART="rootfs2"
+ else
+ fw_setenv active 1 || exit 1
+ CI_UBIPART="rootfs1"
+ fi
+ nand_do_upgrade "$1"
+ ;;
linksys,ea7500-v1 |\
linksys,ea8500)
platform_do_upgrade_linksys "$1"
diff --git a/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts
new file mode 100644
index 0000000000..6d216bd85e
--- /dev/null
+++ b/target/linux/ipq806x/files-5.4/arch/arm/boot/dts/qcom-ipq8068-ecw5410.dts
@@ -0,0 +1,400 @@
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Edgecore ECW5410";
+ compatible = "edgecore,ecw5410", "qcom,ipq8064";
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nss@40000000 {
+ reg = <0x40000000 0x1000000>;
+ no-map;
+ };
+
+ smem: smem@41000000 {
+ reg = <0x41000000 0x200000>;
+ no-map;
+ };
+
+ wifi_dump@44000000 {
+ reg = <0x44000000 0x600000>;
+ no-map;
+ };
+
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ cpus {
+ idle-states {
+ CPU_SPC: spc {
+ status = "disabled";
+ };
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+ serial1 = &gsbi1_serial;
+ mdio-gpio0 = &mdio0;
+ ethernet0 = &gmac3;
+ ethernet1 = &gmac2;
+
+ led-boot = &power_green;
+ led-failsafe = &power_red;
+ led-running = &power_green;
+ led-upgrade = &power_green;
+ };
+
+ chosen {
+ bootargs-append = " console=ttyMSM0,115200n8 root=/dev/ubiblock0_1";
+ stdout-path = "serial0:115200n8";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ power_green: power_green {
+ label = "ecw5410:green:power";
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g_green {
+ label = "ecw5410:green:wlan2g";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g_yellow {
+ label = "ecw5410:yellow:wlan2g";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan5g_green {
+ label = "ecw5410:green:wlan5g";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+ };
+
+ power_red: power_red {
+ label = "ecw5410:red:power";
+ gpios = <&qcom_pinmux 28 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan5g_yellow {
+ label = "ecw5410:yellow:wlan5g";
+ gpios = <&qcom_pinmux 59 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+
+&qcom_pinmux {
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-pull-down;
+ };
+
+ clk {
+ pins = "gpio21";
+ function = "gsbi5";
+ drive-strength = <12>;
+ bias-pull-down;
+ };
+
+ cs {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ nand_pins: nand_pins {
+ disable {
+ pins = "gpio34", "gpio35", "gpio36", "gpio37",
+ "gpio38";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ function = "nand";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42", "gpio43",
+ "gpio44", "gpio45", "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio16", "gpio23", "gpio24", "gpio26",
+ "gpio28", "gpio59";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ button_pins: button_pins {
+ mux {
+ pins = "gpio25";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ uart1_pins: uart1_pins {
+ mux {
+ pins = "gpio51", "gpio52", "gpio53", "gpio54";
+ function = "gsbi1";
+ drive-strength = <12>;
+ bias-none;
+ };
+ };
+};
+
+&gsbi1 {
+ qcom,mode = <GSBI_PROT_UART_W_FC>;
+ status = "okay";
+
+ serial@12450000 {
+ status = "okay";
+
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+
+ serial@16340000 {
+ status = "okay";
+ };
+
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&gsbi5 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "okay";
+
+ spi4: spi@1a280000 {
+ status = "okay";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "qcom,smem";
+ };
+ };
+ };
+};
+
+&hs_phy_0 { /* USB3 port 0 HS phy */
+ status = "okay";
+};
+
+&hs_phy_1 { /* USB3 port 1 HS phy */
+ status = "okay";
+};
+
+&ss_phy_0 { /* USB3 port 0 SS phy */
+ status = "okay";
+};
+
+&ss_phy_1 { /* USB3 port 1 SS phy */
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+
+ /delete-property/ pinctrl-0;
+ /delete-property/ pinctrl-names;
+ /delete-property/ perst-gpios;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
+ };
+ };
+};
+
+&pcie2 {
+ status = "okay";
+
+ /delete-property/ pinctrl-0;
+ /delete-property/ pinctrl-names;
+ /delete-property/ perst-gpios;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "Edgecore-ECW5410-L";
+ };
+ };
+};
+
+&soc {
+ nand@1ac00000 {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ compatible = "qcom,nandcs";
+
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ rootfs1@0 {
+ label = "rootfs1";
+ reg = <0x0000000 0x4000000>;
+ };
+
+ rootfs2@4000000 {
+ label = "rootfs2";
+ reg = <0x4000000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ mdio1: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+&gmac2 {
+ status = "okay";
+
+ qcom,id = <2>;
+ mdiobus = <&mdio0>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy1>;
+};
+
+&gmac3 {
+ status = "okay";
+
+ qcom,id = <3>;
+ mdiobus = <&mdio1>;
+
+ phy-mode = "sgmii";
+ phy-handle = <&phy0>;
+};
+
+&adm_dma {
+ status = "okay";
+};
diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile
index 5cc66daa21..3b86760a19 100644
--- a/target/linux/ipq806x/image/Makefile
+++ b/target/linux/ipq806x/image/Makefile
@@ -126,6 +126,18 @@ define Device/linksys_ea7500-v1
endef
TARGET_DEVICES += linksys_ea7500-v1
+define Device/edgecore_ecw5410
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ DEVICE_TITLE := Edgecore ECW5410
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ DEVICE_DTS := qcom-ipq8068-ecw5410
+ DEVICE_DTS_CONFIG := config@v2.0-ap160
+ DEVICE_PACKAGES := ath10k-firmware-qca9984-ct ipq-wifi-edgecore_ecw5410
+endef
+TARGET_DEVICES += edgecore_ecw5410
+
define Device/linksys_ea8500
$(call Device/LegacyImage)
DEVICE_VENDOR := Linksys
diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
index 8cdd198c29..7e15b87e39 100644
--- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -843,6 +843,19 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -843,6 +843,20 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk07.1-c1.dtb \
qcom-ipq4019-ap.dk07.1-c2.dtb \
qcom-ipq8064-ap148.dtb \
@@ -27,6 +27,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq8064-wxr-2533dhp.dtb \
+ qcom-ipq8065-nbg6817.dtb \
+ qcom-ipq8065-r7800.dtb \
++ qcom-ipq8068-ecw5410.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
qcom-msm8974-fairphone-fp2.dtb \