diff options
Diffstat (limited to 'target/linux/kirkwood/files-4.14')
4 files changed, 0 insertions, 671 deletions
diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts deleted file mode 100644 index af20cf9e2c..0000000000 --- a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts +++ /dev/null @@ -1,124 +0,0 @@ -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6281.dtsi" - -/ { - model = "Seagate GoFlex Home"; - compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - aliases { - led-boot = &led_health; - led-failsafe = &led_fault; - led-running = &led_health; - led-upgrade = &led_fault; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x8000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pmx_usb_power_enable: pmx-usb-power-enable { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - pmx_led_white: pmx-led-white { - marvell,pins = "mpp40"; - marvell,function = "gpio"; - }; - pmx_led_green: pmx-led_green { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - pmx_led_orange: pmx-led-orange { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - }; - serial@12000 { - status = "ok"; - }; - - sata@80000 { - status = "okay"; - nr-ports = <2>; - }; - - }; - gpio-leds { - compatible = "gpio-leds"; - - led_health: health { - label = "status:green:health"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - led_fault: fault { - label = "status:orange:fault"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - misc { - label = "status:white:misc"; - gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; - linux,default-trigger = "disk-activity"; - }; - }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_usb_power_enable>; - pinctrl-names = "default"; - - usb_power: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "USB Power"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - enable-active-high; - regulator-always-on; - regulator-boot-on; - gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&nand { - chip-delay = <40>; - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x0000000 0x100000>; - read-only; - }; - - partition@100000 { - label = "ubi"; - reg = <0x100000 0x0ff00000>; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - reg = <0>; - }; -}; - -ð0 { - status = "okay"; - ethernet0-port@0 { - phy-handle = <ðphy0>; - }; -}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts deleted file mode 100644 index 004ce10219..0000000000 --- a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts +++ /dev/null @@ -1,250 +0,0 @@ -/* - * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 - * - * (c) 2013 Jonas Gorski <jogo@openwrt.org> - * (c) 2013 Deutsche Telekom Innovation Laboratories - * (c) 2014 Luka Perkov <luka@openwrt.org> - * (c) 2014 Dan Walters <dan@walters.io> - * - * This file is licensed under the terms of the GNU General Public - * License version 2. This program is licensed "as is" without any - * warranty of any kind, whether express or implied. - */ - -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6282.dtsi" - -/ { - model = "Linksys Audi (EA3500)"; - compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x4000000>; - }; - - aliases { - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; - serial0 = &uart0; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; - pinctrl-names = "default"; - - wps { - label = "WPS Button"; - linux,code = <KEY_WPS_BUTTON>; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - - reset { - label = "Reset Button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = < &pmx_led_green_power >; - pinctrl-names = "default"; - - led_power: power { - label = "audi:green:power"; - gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - }; - - mvsw61xx { - compatible = "marvell,88e6171"; - status = "okay"; - reg = <0x10>; - - mii-bus = <&mdio>; - cpu-port-0 = <5>; - cpu-port-1 = <6>; - is-indirect; - }; - - dsa { - compatible = "marvell,dsa"; - #address-cells = <2>; - #size-cells = <0>; - - dsa,ethernet = <ð0port>; - dsa,mii-bus = <&mdio>; - - switch@16,0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <16 0>; /* MDIO address 16, switch 0 in tree */ - - port@0 { - reg = <0>; - label = "ethernet1"; - }; - - port@1 { - reg = <1>; - label = "ethernet2"; - }; - - port@2 { - reg = <2>; - label = "ethernet3"; - }; - - port@3 { - reg = <3>; - label = "ethernet4"; - }; - - port@4 { - reg = <4>; - label = "internet"; - }; - - port@5 { - reg = <5>; - label = "cpu"; - }; - }; - }; -}; - -&pinctrl { - pmx_led_green_power: pmx-led-green-power { - marvell,pins = "mpp7"; - marvell,function = "gpo"; - }; - pmx_btn_wps: pmx-btn-wps { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - pmx_btn_reset: pmx-btn-reset { - marvell,pins = "mpp48"; - marvell,function = "gpio"; - }; -}; - -&nand { - status = "okay"; - pinctrl-0 = <&pmx_nand>; - pinctrl-names = "default"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x80000>; - read-only; - }; - - partition@80000 { - label = "u_env"; - reg = <0x80000 0x4000>; - }; - - partition@84000 { - label = "s_env"; - reg = <0x84000 0x4000>; - }; - - partition@200000 { - label = "kernel1"; - reg = <0x200000 0x290000>; - }; - - partition@490000 { - label = "rootfs1"; - reg = <0x490000 0x1170000>; - }; - - partition@1600000 { - label = "kernel2"; - reg = <0x1600000 0x290000>; - }; - - partition@1890000 { - label = "rootfs2"; - reg = <0x1890000 0x1170000>; - }; - - partition@2a00000 { - label = "syscfg"; - reg = <0x2a00000 0x1600000>; - }; - - partition@88000 { - label = "unused"; - reg = <0x88000 0x178000>; - }; - - }; -}; - -&pciec { - status = "okay"; -}; - -&pcie0 { - status = "okay"; -}; - -&pcie1 { - status = "okay"; -}; - -&mdio { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; - -/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set - * fixed speed and duplex. - */ -ð0 { - status = "okay"; - ethernet0-port@0 { - speed = <1000>; - duplex = <1>; - }; -}; - -/* eth1 is connected to the switch at port 6. However DSA only supports a - * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. - */ -ð1 { - status = "okay"; - ethernet1-port@0 { - speed = <1000>; - duplex = <1>; - }; -}; - -/* There is no battery on the board, so the RTC does not keep - * time when there is no power, making it useless. - */ -&rtc { - status = "disabled"; -}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts deleted file mode 100644 index a83a55af07..0000000000 --- a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts +++ /dev/null @@ -1,132 +0,0 @@ -/dts-v1/; - -#include "kirkwood-nsa3x0-common.dtsi" - -/* - * There are at least two different NSA310 designs. This variant has - * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. - */ - -/ { - model = "ZyXEL NSA310b"; - compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - aliases { - led-boot = &led_green_sys; - led-failsafe = &led_red_sys; - led-running = &led_green_sys; - led-upgrade = &led_red_sys; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x10000000>; - }; - - chosen { - bootargs = "console=ttyS0,115200"; - stdout-path = &uart0; - }; - - ocp@f1000000 { - pinctrl: pin-controller@10000 { - pinctrl-names = "default"; - - pmx_led_esata_green: pmx-led-esata-green { - marvell,pins = "mpp12"; - marvell,function = "gpio"; - }; - - pmx_led_esata_red: pmx-led-esata-red { - marvell,pins = "mpp13"; - marvell,function = "gpio"; - }; - - pmx_led_usb_green: pmx-led-usb-green { - marvell,pins = "mpp15"; - marvell,function = "gpio"; - }; - - pmx_led_usb_red: pmx-led-usb-red { - marvell,pins = "mpp16"; - marvell,function = "gpio"; - }; - - pmx_led_sys_green: pmx-led-sys-green { - marvell,pins = "mpp28"; - marvell,function = "gpio"; - }; - - pmx_led_sys_red: pmx-led-sys-red { - marvell,pins = "mpp29"; - marvell,function = "gpio"; - }; - - pmx_led_hdd_green: pmx-led-hdd-green { - marvell,pins = "mpp41"; - marvell,function = "gpio"; - }; - - pmx_led_hdd_red: pmx-led-hdd-red { - marvell,pins = "mpp42"; - marvell,function = "gpio"; - }; - - }; - - i2c@11000 { - status = "okay"; - - lm85: lm85@2e { - compatible = "national,lm85"; - reg = <0x2e>; - }; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - led_green_sys: green-sys { - label = "nsa310:green:sys"; - gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - led_red_sys: red-sys { - label = "nsa310:red:sys"; - gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; - }; - green-hdd { - label = "nsa310:green:hdd"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - }; - red-hdd { - label = "nsa310:red:hdd"; - gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; - }; - green-esata { - label = "nsa310:green:esata"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - red-esata { - label = "nsa310:red:esata"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - green-usb { - label = "nsa310:green:usb"; - gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; - }; - red-usb { - label = "nsa310:red:usb"; - gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; - }; - green-copy { - label = "nsa310:green:copy"; - gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; - }; - red-copy { - label = "nsa310:red:copy"; - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - }; - }; -}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts deleted file mode 100644 index 9296c3fc71..0000000000 --- a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts +++ /dev/null @@ -1,165 +0,0 @@ -/dts-v1/; - -#include "kirkwood.dtsi" -#include "kirkwood-6282.dtsi" - -/ { - model = "Cisco Systems ON100"; - compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; - - memory { - device_type = "memory"; - reg = <0x00000000 0x20000000>; - }; - - aliases { - led-boot = &led_health_green; - led-failsafe = &led_health_red; - led-running = &led_health_green; - led-upgrade = &led_health_red; - serial0 = &uart0; - }; - - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = "serial0:115200n8"; - }; - - gpio_keys { - compatible = "gpio-keys"; - #address-cells = <1>; - #size-cells = <0>; - pinctrl-0 = <&pmx_btn_reset>; - pinctrl-names = "default"; - - button@1 { - label = "Reset Button"; - linux,code = <KEY_RESTART>; - gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; - pinctrl-names = "default"; - - led_health_green: health_green { - label = "on100:green:health"; - gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - - led_health_red: health_red { - label = "on100:red:health"; - gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; - }; - - health2_green { - label = "on100:green:health2"; - gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - }; - - health2_red { - label = "on100:red:health2"; - gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; - }; -}; - -ð0 { - status = "okay"; - - ethernet0-port@0 { - phy-handle = <ðphy0>; - phy-connection-type = "rgmii-id"; - }; -}; - -ð1 { - status = "okay"; - - ethernet1-port@0 { - phy-handle = <ðphy1>; - phy-connection-type = "rgmii-id"; - }; -}; - -&mdio { - status = "okay"; - - ethphy0: ethernet-phy@0 { - /* Marvell 88E1121R */ - compatible = "ethernet-phy-id0141.0cb0", - "ethernet-phy-ieee802.3-c22"; - reg = <0>; - }; - - ethphy1: ethernet-phy@1 { - /* Marvell 88E1121R */ - compatible = "ethernet-phy-id0141.0cb0", - "ethernet-phy-ieee802.3-c22"; - reg = <1>; - }; -}; - -&nand { - status = "okay"; - - partition@0 { - label = "u-boot"; - reg = <0x00000000 0x000a0000>; - read-only; - }; - - partition@a0000 { - label = "u-boot environment"; - reg = <0x000a0000 0x00020000>; - read-only; - }; - - partition@c0000 { - label = "kernel"; - reg = <0x000c0000 0x00540000>; - }; - - partition@600000 { - label = "ubi"; - reg = <0x00600000 0x1fa00000>; - }; -}; - -&pinctrl { - pmx_led_health_r: pmx-led-health-r { - marvell,pins = "mpp45"; - marvell,function = "gpio"; - }; - - pmx_led_health_g: pmx-led-health-g { - marvell,pins = "mpp44"; - marvell,function = "gpio"; - }; - - pmx_led_health2_r: pmx-led-health2-r { - marvell,pins = "mpp47"; - marvell,function = "gpio"; - }; - - pmx_led_health2_g: pmx-led-health2-g { - marvell,pins = "mpp46"; - marvell,function = "gpio"; - }; - - pmx_btn_reset: pmx-led-reset { - marvell,pins = "mpp31"; - marvell,function = "gpio"; - }; -}; - -&sdio { - status = "okay"; -}; - -&uart0 { - status = "okay"; -}; |