diff options
Diffstat (limited to 'target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h')
-rw-r--r-- | target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h | 481 |
1 files changed, 481 insertions, 0 deletions
diff --git a/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h new file mode 100644 index 0000000000..71acc7c92c --- /dev/null +++ b/target/linux/mediatek/files-5.4/drivers/net/phy/rtk/rtl8367c/include/led.h @@ -0,0 +1,481 @@ +/* + * Copyright (C) 2013 Realtek Semiconductor Corp. + * All Rights Reserved. + * + * Unless you and Realtek execute a separate written software license + * agreement governing use of this software, this software is licensed + * to you under the terms of the GNU General Public License version 2, + * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt + * + * Purpose : RTL8367/RTL8367C switch high-level API + * + * Feature : The file includes LED module high-layer API defination + * + */ + +#ifndef __RTK_API_LED_H__ +#define __RTK_API_LED_H__ + +typedef enum rtk_led_operation_e +{ + LED_OP_SCAN=0, + LED_OP_PARALLEL, + LED_OP_SERIAL, + LED_OP_END, +}rtk_led_operation_t; + + +typedef enum rtk_led_active_e +{ + LED_ACTIVE_HIGH=0, + LED_ACTIVE_LOW, + LED_ACTIVE_END, +}rtk_led_active_t; + +typedef enum rtk_led_config_e +{ + LED_CONFIG_LEDOFF=0, + LED_CONFIG_DUPCOL, + LED_CONFIG_LINK_ACT, + LED_CONFIG_SPD1000, + LED_CONFIG_SPD100, + LED_CONFIG_SPD10, + LED_CONFIG_SPD1000ACT, + LED_CONFIG_SPD100ACT, + LED_CONFIG_SPD10ACT, + LED_CONFIG_SPD10010ACT, + LED_CONFIG_LOOPDETECT, + LED_CONFIG_EEE, + LED_CONFIG_LINKRX, + LED_CONFIG_LINKTX, + LED_CONFIG_MASTER, + LED_CONFIG_ACT, + LED_CONFIG_END, +}rtk_led_congig_t; + +typedef struct rtk_led_ability_s +{ + rtk_enable_t link_10m; + rtk_enable_t link_100m; + rtk_enable_t link_500m; + rtk_enable_t link_1000m; + rtk_enable_t act_rx; + rtk_enable_t act_tx; +}rtk_led_ability_t; + +typedef enum rtk_led_blink_rate_e +{ + LED_BLINKRATE_32MS=0, + LED_BLINKRATE_64MS, + LED_BLINKRATE_128MS, + LED_BLINKRATE_256MS, + LED_BLINKRATE_512MS, + LED_BLINKRATE_1024MS, + LED_BLINKRATE_48MS, + LED_BLINKRATE_96MS, + LED_BLINKRATE_END, +}rtk_led_blink_rate_t; + +typedef enum rtk_led_group_e +{ + LED_GROUP_0 = 0, + LED_GROUP_1, + LED_GROUP_2, + LED_GROUP_END +}rtk_led_group_t; + + +typedef enum rtk_led_force_mode_e +{ + LED_FORCE_NORMAL=0, + LED_FORCE_BLINK, + LED_FORCE_OFF, + LED_FORCE_ON, + LED_FORCE_END +}rtk_led_force_mode_t; + +typedef enum rtk_led_serialOutput_e +{ + SERIAL_LED_NONE = 0, + SERIAL_LED_0, + SERIAL_LED_0_1, + SERIAL_LED_0_2, + SERIAL_LED_END, +}rtk_led_serialOutput_t; + + +/* Function Name: + * rtk_led_enable_set + * Description: + * Set Led enable congiuration + * Input: + * group - LED group id. + * pPortmask - LED enable port mask. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can be used to enable LED per port per group. + */ +extern rtk_api_ret_t rtk_led_enable_set(rtk_led_group_t group, rtk_portmask_t *pPortmask); + +/* Function Name: + * rtk_led_enable_get + * Description: + * Get Led enable congiuration + * Input: + * group - LED group id. + * Output: + * pPortmask - LED enable port mask. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can be used to get LED enable status. + */ +extern rtk_api_ret_t rtk_led_enable_get(rtk_led_group_t group, rtk_portmask_t *pPortmask); + +/* Function Name: + * rtk_led_operation_set + * Description: + * Set Led operation mode + * Input: + * mode - LED operation mode. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can set Led operation mode. + * The modes that can be set are as following: + * - LED_OP_SCAN, + * - LED_OP_PARALLEL, + * - LED_OP_SERIAL, + */ +extern rtk_api_ret_t rtk_led_operation_set(rtk_led_operation_t mode); + +/* Function Name: + * rtk_led_operation_get + * Description: + * Get Led operation mode + * Input: + * None + * Output: + * pMode - Support LED operation mode. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can get Led operation mode. + * The modes that can be set are as following: + * - LED_OP_SCAN, + * - LED_OP_PARALLEL, + * - LED_OP_SERIAL, + */ +extern rtk_api_ret_t rtk_led_operation_get(rtk_led_operation_t *pMode); + +/* Function Name: + * rtk_led_modeForce_set + * Description: + * Set Led group to congiuration force mode + * Input: + * port - port ID + * group - Support LED group id. + * mode - Support LED force mode. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * RT_ERR_PORT_ID - Error Port ID + * Note: + * The API can force to one force mode. + * The force modes that can be set are as following: + * - LED_FORCE_NORMAL, + * - LED_FORCE_BLINK, + * - LED_FORCE_OFF, + * - LED_FORCE_ON. + */ +extern rtk_api_ret_t rtk_led_modeForce_set(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t mode); + +/* Function Name: + * rtk_led_modeForce_get + * Description: + * Get Led group to congiuration force mode + * Input: + * port - port ID + * group - Support LED group id. + * pMode - Support LED force mode. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * RT_ERR_PORT_ID - Error Port ID + * Note: + * The API can get forced Led group mode. + * The force modes that can be set are as following: + * - LED_FORCE_NORMAL, + * - LED_FORCE_BLINK, + * - LED_FORCE_OFF, + * - LED_FORCE_ON. + */ +extern rtk_api_ret_t rtk_led_modeForce_get(rtk_port_t port, rtk_led_group_t group, rtk_led_force_mode_t *pMode); + +/* Function Name: + * rtk_led_blinkRate_set + * Description: + * Set LED blinking rate + * Input: + * blinkRate - blinking rate. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * ASIC support 6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms. + */ +extern rtk_api_ret_t rtk_led_blinkRate_set(rtk_led_blink_rate_t blinkRate); + +/* Function Name: + * rtk_led_blinkRate_get + * Description: + * Get LED blinking rate at mode 0 to mode 3 + * Input: + * None + * Output: + * pBlinkRate - blinking rate. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * There are 6 types of LED blinking rates at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms. + */ +extern rtk_api_ret_t rtk_led_blinkRate_get(rtk_led_blink_rate_t *pBlinkRate); + +/* Function Name: + * rtk_led_groupConfig_set + * Description: + * Set per group Led to congiuration mode + * Input: + * group - LED group. + * config - LED configuration + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can set LED indicated information configuration for each LED group with 1 to 1 led mapping to each port. + * - Definition LED Statuses Description + * - 0000 LED_Off LED pin Tri-State. + * - 0001 Dup/Col Collision, Full duplex Indicator. + * - 0010 Link/Act Link, Activity Indicator. + * - 0011 Spd1000 1000Mb/s Speed Indicator. + * - 0100 Spd100 100Mb/s Speed Indicator. + * - 0101 Spd10 10Mb/s Speed Indicator. + * - 0110 Spd1000/Act 1000Mb/s Speed/Activity Indicator. + * - 0111 Spd100/Act 100Mb/s Speed/Activity Indicator. + * - 1000 Spd10/Act 10Mb/s Speed/Activity Indicator. + * - 1001 Spd100 (10)/Act 10/100Mb/s Speed/Activity Indicator. + * - 1010 LoopDetect LoopDetect Indicator. + * - 1011 EEE EEE Indicator. + * - 1100 Link/Rx Link, Activity Indicator. + * - 1101 Link/Tx Link, Activity Indicator. + * - 1110 Master Link on Master Indicator. + * - 1111 Act Activity Indicator. Low for link established. + */ +extern rtk_api_ret_t rtk_led_groupConfig_set(rtk_led_group_t group, rtk_led_congig_t config); + +/* Function Name: + * rtk_led_groupConfig_get + * Description: + * Get Led group congiuration mode + * Input: + * group - LED group. + * Output: + * pConfig - LED configuration. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can get LED indicated information configuration for each LED group. + */ +extern rtk_api_ret_t rtk_led_groupConfig_get(rtk_led_group_t group, rtk_led_congig_t *pConfig); + +/* Function Name: + * rtk_led_groupAbility_set + * Description: + * Configure per group Led ability + * Input: + * group - LED group. + * pAbility - LED ability + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * None. + */ + +extern rtk_api_ret_t rtk_led_groupAbility_set(rtk_led_group_t group, rtk_led_ability_t *pAbility); + +/* Function Name: + * rtk_led_groupAbility_get + * Description: + * Get per group Led ability + * Input: + * group - LED group. + * pAbility - LED ability + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * None. + */ + +extern rtk_api_ret_t rtk_led_groupAbility_get(rtk_led_group_t group, rtk_led_ability_t *pAbility); + +/* Function Name: + * rtk_led_serialMode_set + * Description: + * Set Led serial mode active congiuration + * Input: + * active - LED group. + * Output: + * None + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can set LED serial mode active congiuration. + */ +extern rtk_api_ret_t rtk_led_serialMode_set(rtk_led_active_t active); + +/* Function Name: + * rtk_led_serialMode_get + * Description: + * Get Led group congiuration mode + * Input: + * group - LED group. + * Output: + * pConfig - LED configuration. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Invalid input parameters. + * Note: + * The API can get LED serial mode active configuration. + */ +extern rtk_api_ret_t rtk_led_serialMode_get(rtk_led_active_t *pActive); + +/* Function Name: + * rtk_led_OutputEnable_set + * Description: + * This API set LED I/O state. + * Input: + * enabled - LED I/O state + * Output: + * None. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Error parameter + * Note: + * This API set LED I/O state. + */ +extern rtk_api_ret_t rtk_led_OutputEnable_set(rtk_enable_t state); + + +/* Function Name: + * rtk_led_OutputEnable_get + * Description: + * This API get LED I/O state. + * Input: + * None. + * Output: + * pEnabled - LED I/O state + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Error parameter + * Note: + * This API set current LED I/O state. + */ +extern rtk_api_ret_t rtk_led_OutputEnable_get(rtk_enable_t *pState); + +/* Function Name: + * rtk_led_serialModePortmask_set + * Description: + * This API configure Serial LED output Group and portmask + * Input: + * output - output group + * pPortmask - output portmask + * Output: + * None. + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Error parameter + * Note: + * None. + */ +extern rtk_api_ret_t rtk_led_serialModePortmask_set(rtk_led_serialOutput_t output, rtk_portmask_t *pPortmask); + +/* Function Name: + * rtk_led_serialModePortmask_get + * Description: + * This API get Serial LED output Group and portmask + * Input: + * None. + * Output: + * pOutput - output group + * pPortmask - output portmask + * Return: + * RT_ERR_OK - OK + * RT_ERR_FAILED - Failed + * RT_ERR_SMI - SMI access error + * RT_ERR_INPUT - Error parameter + * Note: + * None. + */ +extern rtk_api_ret_t rtk_led_serialModePortmask_get(rtk_led_serialOutput_t *pOutput, rtk_portmask_t *pPortmask); + +#endif /* __RTK_API_LED_H__ */ |