diff options
Diffstat (limited to 'target')
155 files changed, 18016 insertions, 0 deletions
diff --git a/target/linux/brcm63xx/config-3.18 b/target/linux/brcm63xx/config-3.18 new file mode 100644 index 0000000000..b323da40ca --- /dev/null +++ b/target/linux/brcm63xx/config-3.18 @@ -0,0 +1,231 @@ +CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y +CONFIG_ARCH_DISCARD_MEMBLOCK=y +CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y +# CONFIG_ARCH_HAS_SG_CHAIN is not set +CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y +# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +# CONFIG_AUDIT_ARCH_COMPAT_GENERIC is not set +CONFIG_B53=y +CONFIG_B53_MMAP_DRIVER=y +CONFIG_B53_PHY_DRIVER=y +CONFIG_B53_PHY_FIXUP=y +CONFIG_B53_SPI_DRIVER=y +# CONFIG_B53_SRAB_DRIVER is not set +CONFIG_BCM6345_EXT_IRQ=y +CONFIG_BCM6345_L2_IRQ=y +CONFIG_BCM63XX=y +CONFIG_BCM63XX_CPU_3368=y +CONFIG_BCM63XX_CPU_6318=y +CONFIG_BCM63XX_CPU_63268=y +CONFIG_BCM63XX_CPU_6328=y +CONFIG_BCM63XX_CPU_6338=y +CONFIG_BCM63XX_CPU_6345=y +CONFIG_BCM63XX_CPU_6348=y +CONFIG_BCM63XX_CPU_6358=y +CONFIG_BCM63XX_CPU_6362=y +CONFIG_BCM63XX_CPU_6368=y +CONFIG_BCM63XX_EHCI=y +CONFIG_BCM63XX_ENET=y +CONFIG_BCM63XX_OHCI=y +CONFIG_BCM63XX_PHY=y +CONFIG_BCM63XX_WDT=y +CONFIG_BCMA=y +CONFIG_BCMA_BLOCKIO=y +# CONFIG_BCMA_DEBUG is not set +# CONFIG_BCMA_DRIVER_GMAC_CMN is not set +# CONFIG_BCMA_DRIVER_MIPS is not set +# CONFIG_BCMA_DRIVER_PCI_HOSTMODE is not set +CONFIG_BCMA_HOST_PCI=y +CONFIG_BCMA_HOST_PCI_POSSIBLE=y +# CONFIG_BCMA_HOST_SOC is not set +CONFIG_BOARD_BCM63XX_DT=y +CONFIG_BOARD_BCM963XX=y +CONFIG_BOARD_LIVEBOX=y +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_CEVT_R4K=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200" +CONFIG_CMDLINE_BOOL=y +# CONFIG_CMDLINE_OVERRIDE is not set +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_BMIPS=y +CONFIG_CPU_BMIPS32_3300=y +CONFIG_CPU_BMIPS4350=y +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_MIPS32=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_R4K_FPU=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CSRC_R4K=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_DTC=y +CONFIG_EARLY_PRINTK=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_DEVRES=y +CONFIG_GPIO_SYSFS=y +# CONFIG_HAMRADIO is not set +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_BPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DEBUG_STACKOVERFLOW=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_ATTRS=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MEMBLOCK_NODE_MAP=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HW_RANDOM_BCM63XX=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +CONFIG_HZ_PERIODIC=y +CONFIG_IMAGE_CMDLINE_HACK=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IP_PIMSM_V1=y +CONFIG_IP_PIMSM_V2=y +CONFIG_IRQCHIP=y +CONFIG_IRQ_CPU=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_KERNFS=y +CONFIG_KEXEC=y +CONFIG_LEDS_GPIO=y +CONFIG_LIBFDT=y +CONFIG_MDIO_BOARDINFO=y +CONFIG_MIPS=y +CONFIG_MIPS_APPENDED_DTB=y +# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=4 +CONFIG_MIPS_L1_CACHE_SHIFT_4=y +# CONFIG_MIPS_MACHINE is not set +CONFIG_MIPS_O32_FP64_SUPPORT=y +# CONFIG_MIPS_PARAVIRT is not set +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MODULE_FORCE_LOAD=y +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD_BCM63XX_PARTS=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_BE_BYTE_SWAP=y +# CONFIG_MTD_CFI_GEOMETRY is not set +# CONFIG_MTD_CFI_NOSWAP is not set +CONFIG_MTD_CFI_STAA=y +CONFIG_MTD_CMDLINE_PARTS=y +# CONFIG_MTD_COMPLEX_MAPPINGS is not set +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_M25P80=y +CONFIG_MTD_PHYSMAP=y +CONFIG_MTD_REDBOOT_PARTS=y +CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y +CONFIG_MTD_SPI_NOR=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +# CONFIG_NO_IOPORT_MAP is not set +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_MDIO=y +CONFIG_OF_MTD=y +CONFIG_OF_NET=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_PCI=y +# CONFIG_PCIEAER is not set +CONFIG_PCIEPORTBUS=y +CONFIG_PCI_DOMAINS=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PHYLIB=y +CONFIG_POSIX_MQUEUE=y +CONFIG_POSIX_MQUEUE_SYSCTL=y +# CONFIG_PREEMPT_RCU is not set +# CONFIG_RCU_STALL_COMMON is not set +CONFIG_RELAY=y +CONFIG_RTL8366_SMI=y +CONFIG_RTL8367_PHY=y +# CONFIG_SCSI_DMA is not set +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_BCM63XX=y +CONFIG_SERIAL_BCM63XX_CONSOLE=y +CONFIG_SPI=y +CONFIG_SPI_BCM63XX=y +CONFIG_SPI_BCM63XX_HSSPI=y +CONFIG_SPI_BITBANG=y +CONFIG_SPI_GPIO=y +CONFIG_SPI_MASTER=y +CONFIG_SQUASHFS_EMBEDDED=y +CONFIG_SSB=y +CONFIG_SSB_B43_PCI_BRIDGE=y +CONFIG_SSB_BLOCKIO=y +# CONFIG_SSB_DRIVER_MIPS is not set +CONFIG_SSB_DRIVER_PCICORE=y +CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y +CONFIG_SSB_PCIHOST=y +CONFIG_SSB_PCIHOST_POSSIBLE=y +CONFIG_SSB_SPROM=y +CONFIG_SWAP_IO_SPACE=y +CONFIG_SWCONFIG=y +CONFIG_SYNC_R4K=y +CONFIG_SYS_HAS_CPU_BMIPS=y +CONFIG_SYS_HAS_CPU_BMIPS32_3300=y +CONFIG_SYS_HAS_CPU_BMIPS4350=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_HOTPLUG_CPU=y +CONFIG_SYS_SUPPORTS_SMP=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_USB_SUPPORT=y +CONFIG_USE_OF=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_WATCHDOG_NOWAYOUT=y +CONFIG_WEAK_ORDERING=y +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/brcm63xx/patches-3.18/030-MIPS-Always-use-IRQ-domains-for-CPU-IRQs.patch b/target/linux/brcm63xx/patches-3.18/030-MIPS-Always-use-IRQ-domains-for-CPU-IRQs.patch new file mode 100644 index 0000000000..e7d091c95d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/030-MIPS-Always-use-IRQ-domains-for-CPU-IRQs.patch @@ -0,0 +1,98 @@ +From 0f84c305351c993e4307e1e8c128d44760314e31 Mon Sep 17 00:00:00 2001 +From: Andrew Bresticker <abrestic@chromium.org> +Date: Thu, 18 Sep 2014 14:47:07 -0700 +Subject: [PATCH 1/3] MIPS: Always use IRQ domains for CPU IRQs + +Use an IRQ domain for the 8 CPU IRQs in both the DT and non-DT cases. + +Signed-off-by: Andrew Bresticker <abrestic@chromium.org> +Reviewed-by: Qais Yousef <qais.yousef@imgtec.com> +Tested-by: Qais Yousef <qais.yousef@imgtec.com> +Cc: Thomas Gleixner <tglx@linutronix.de> +Cc: Jason Cooper <jason@lakedaemon.net> +Cc: Andrew Bresticker <abrestic@chromium.org> +Cc: Jeffrey Deans <jeffrey.deans@imgtec.com> +Cc: Markos Chandras <markos.chandras@imgtec.com> +Cc: Paul Burton <paul.burton@imgtec.com> +Cc: Qais Yousef <qais.yousef@imgtec.com> +Cc: Jonas Gorski <jogo@openwrt.org> +Cc: John Crispin <blogic@openwrt.org> +Cc: David Daney <ddaney.cavm@gmail.com> +Cc: linux-mips@linux-mips.org +Cc: linux-kernel@vger.kernel.org +Patchwork: https://patchwork.linux-mips.org/patch/7799/ +Signed-off-by: Ralf Baechle <ralf@linux-mips.org> +--- + arch/mips/Kconfig | 1 + + arch/mips/kernel/irq_cpu.c | 36 +++++++++++------------------------- + 2 files changed, 12 insertions(+), 25 deletions(-) + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -1056,6 +1056,7 @@ config MIPS_HUGE_TLB_SUPPORT + + config IRQ_CPU + bool ++ select IRQ_DOMAIN + + config IRQ_CPU_RM7K + bool +--- a/arch/mips/kernel/irq_cpu.c ++++ b/arch/mips/kernel/irq_cpu.c +@@ -94,28 +94,6 @@ static struct irq_chip mips_mt_cpu_irq_c + .irq_eoi = unmask_mips_irq, + }; + +-void __init mips_cpu_irq_init(void) +-{ +- int irq_base = MIPS_CPU_IRQ_BASE; +- int i; +- +- /* Mask interrupts. */ +- clear_c0_status(ST0_IM); +- clear_c0_cause(CAUSEF_IP); +- +- /* Software interrupts are used for MT/CMT IPI */ +- for (i = irq_base; i < irq_base + 2; i++) +- irq_set_chip_and_handler(i, cpu_has_mipsmt ? +- &mips_mt_cpu_irq_controller : +- &mips_cpu_irq_controller, +- handle_percpu_irq); +- +- for (i = irq_base + 2; i < irq_base + 8; i++) +- irq_set_chip_and_handler(i, &mips_cpu_irq_controller, +- handle_percpu_irq); +-} +- +-#ifdef CONFIG_IRQ_DOMAIN + static int mips_cpu_intc_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hw) + { +@@ -138,8 +116,7 @@ static const struct irq_domain_ops mips_ + .xlate = irq_domain_xlate_onecell, + }; + +-int __init mips_cpu_intc_init(struct device_node *of_node, +- struct device_node *parent) ++static void __init __mips_cpu_irq_init(struct device_node *of_node) + { + struct irq_domain *domain; + +@@ -151,7 +128,16 @@ int __init mips_cpu_intc_init(struct dev + &mips_cpu_intc_irq_domain_ops, NULL); + if (!domain) + panic("Failed to add irqdomain for MIPS CPU"); ++} + ++void __init mips_cpu_irq_init(void) ++{ ++ __mips_cpu_irq_init(NULL); ++} ++ ++int __init mips_cpu_intc_init(struct device_node *of_node, ++ struct device_node *parent) ++{ ++ __mips_cpu_irq_init(of_node); + return 0; + } +-#endif /* CONFIG_IRQ_DOMAIN */ diff --git a/target/linux/brcm63xx/patches-3.18/031-MIPS-Rename-mips_cpu_intc_init-mips_cpu_irq_of_init.patch b/target/linux/brcm63xx/patches-3.18/031-MIPS-Rename-mips_cpu_intc_init-mips_cpu_irq_of_init.patch new file mode 100644 index 0000000000..de0f111e28 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/031-MIPS-Rename-mips_cpu_intc_init-mips_cpu_irq_of_init.patch @@ -0,0 +1,89 @@ +From afe8dc254711b72ba8144295f4a8fcc66d30572d Mon Sep 17 00:00:00 2001 +From: Andrew Bresticker <abrestic@chromium.org> +Date: Thu, 18 Sep 2014 14:47:08 -0700 +Subject: [PATCH 2/3] MIPS: Rename mips_cpu_intc_init() -> + mips_cpu_irq_of_init() + +mips_cpu_intc_init() is used for DT-based initialization of the CPU +IRQ domain. Give it a more appropriate name. + +Signed-off-by: Andrew Bresticker <abrestic@chromium.org> +Reviewed-by: Qais Yousef <qais.yousef@imgtec.com> +Tested-by: Qais Yousef <qais.yousef@imgtec.com> +Cc: Thomas Gleixner <tglx@linutronix.de> +Cc: Jason Cooper <jason@lakedaemon.net> +Cc: Andrew Bresticker <abrestic@chromium.org> +Cc: Jeffrey Deans <jeffrey.deans@imgtec.com> +Cc: Markos Chandras <markos.chandras@imgtec.com> +Cc: Paul Burton <paul.burton@imgtec.com> +Cc: Qais Yousef <qais.yousef@imgtec.com> +Cc: Jonas Gorski <jogo@openwrt.org> +Cc: John Crispin <blogic@openwrt.org> +Cc: David Daney <ddaney.cavm@gmail.com> +Cc: linux-mips@linux-mips.org +Cc: linux-kernel@vger.kernel.org +Patchwork: https://patchwork.linux-mips.org/patch/7800/ +Signed-off-by: Ralf Baechle <ralf@linux-mips.org> +--- + Documentation/devicetree/bindings/mips/cpu_irq.txt | 4 ++-- + arch/mips/include/asm/irq_cpu.h | 4 ++-- + arch/mips/kernel/irq_cpu.c | 4 ++-- + arch/mips/ralink/irq.c | 2 +- + 4 files changed, 7 insertions(+), 7 deletions(-) + +--- a/Documentation/devicetree/bindings/mips/cpu_irq.txt ++++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt +@@ -1,6 +1,6 @@ + MIPS CPU interrupt controller + +-On MIPS the mips_cpu_intc_init() helper can be used to initialize the 8 CPU ++On MIPS the mips_cpu_irq_of_init() helper can be used to initialize the 8 CPU + IRQs from a devicetree file and create a irq_domain for IRQ controller. + + With the irq_domain in place we can describe how the 8 IRQs are wired to the +@@ -36,7 +36,7 @@ Example devicetree: + + Example platform irq.c: + static struct of_device_id __initdata of_irq_ids[] = { +- { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_intc_init }, ++ { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_irq_of_init }, + { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, + {}, + }; +--- a/arch/mips/include/asm/irq_cpu.h ++++ b/arch/mips/include/asm/irq_cpu.h +@@ -19,8 +19,8 @@ extern void rm9k_cpu_irq_init(void); + + #ifdef CONFIG_IRQ_DOMAIN + struct device_node; +-extern int mips_cpu_intc_init(struct device_node *of_node, +- struct device_node *parent); ++extern int mips_cpu_irq_of_init(struct device_node *of_node, ++ struct device_node *parent); + #endif + + #endif /* _ASM_IRQ_CPU_H */ +--- a/arch/mips/kernel/irq_cpu.c ++++ b/arch/mips/kernel/irq_cpu.c +@@ -135,8 +135,8 @@ void __init mips_cpu_irq_init(void) + __mips_cpu_irq_init(NULL); + } + +-int __init mips_cpu_intc_init(struct device_node *of_node, +- struct device_node *parent) ++int __init mips_cpu_irq_of_init(struct device_node *of_node, ++ struct device_node *parent) + { + __mips_cpu_irq_init(of_node); + return 0; +--- a/arch/mips/ralink/irq.c ++++ b/arch/mips/ralink/irq.c +@@ -173,7 +173,7 @@ static int __init intc_of_init(struct de + } + + static struct of_device_id __initdata of_irq_ids[] = { +- { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_intc_init }, ++ { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_irq_of_init }, + { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, + {}, + }; diff --git a/target/linux/brcm63xx/patches-3.18/032-MIPS-Provide-a-generic-plat_irq_dispatch.patch b/target/linux/brcm63xx/patches-3.18/032-MIPS-Provide-a-generic-plat_irq_dispatch.patch new file mode 100644 index 0000000000..79a0436dc6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/032-MIPS-Provide-a-generic-plat_irq_dispatch.patch @@ -0,0 +1,58 @@ +From 85f7cdacbb81db8c4cc8e474837eab1f0e4ff77b Mon Sep 17 00:00:00 2001 +From: Andrew Bresticker <abrestic@chromium.org> +Date: Thu, 18 Sep 2014 14:47:09 -0700 +Subject: [PATCH 3/3] MIPS: Provide a generic plat_irq_dispatch + +For platforms which boot with device-tree or have correctly chained +all external interrupt controllers, a generic plat_irq_dispatch() can +be used. Implement a plat_irq_dispatch() which simply handles all the +pending interrupts as reported by C0_Cause. + +Signed-off-by: Andrew Bresticker <abrestic@chromium.org> +Reviewed-by: Qais Yousef <qais.yousef@imgtec.com> +Tested-by: Qais Yousef <qais.yousef@imgtec.com> +Cc: Thomas Gleixner <tglx@linutronix.de> +Cc: Jason Cooper <jason@lakedaemon.net> +Cc: Andrew Bresticker <abrestic@chromium.org> +Cc: Jeffrey Deans <jeffrey.deans@imgtec.com> +Cc: Markos Chandras <markos.chandras@imgtec.com> +Cc: Paul Burton <paul.burton@imgtec.com> +Cc: Qais Yousef <qais.yousef@imgtec.com> +Cc: Jonas Gorski <jogo@openwrt.org> +Cc: John Crispin <blogic@openwrt.org> +Cc: David Daney <ddaney.cavm@gmail.com> +Cc: linux-mips@linux-mips.org +Cc: linux-kernel@vger.kernel.org +Patchwork: https://patchwork.linux-mips.org/patch/7801/ +Signed-off-by: Ralf Baechle <ralf@linux-mips.org> +--- + arch/mips/kernel/irq_cpu.c | 18 ++++++++++++++++++ + 1 file changed, 18 insertions(+) + +--- a/arch/mips/kernel/irq_cpu.c ++++ b/arch/mips/kernel/irq_cpu.c +@@ -94,6 +94,24 @@ static struct irq_chip mips_mt_cpu_irq_c + .irq_eoi = unmask_mips_irq, + }; + ++asmlinkage void __weak plat_irq_dispatch(void) ++{ ++ unsigned long pending = read_c0_cause() & read_c0_status() & ST0_IM; ++ int irq; ++ ++ if (!pending) { ++ spurious_interrupt(); ++ return; ++ } ++ ++ pending >>= CAUSEB_IP; ++ while (pending) { ++ irq = fls(pending) - 1; ++ do_IRQ(MIPS_CPU_IRQ_BASE + irq); ++ pending &= ~BIT(irq); ++ } ++} ++ + static int mips_cpu_intc_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hw) + { diff --git a/target/linux/brcm63xx/patches-3.18/100-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch b/target/linux/brcm63xx/patches-3.18/100-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch new file mode 100644 index 0000000000..63d385be4e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/100-MIPS-BCM63XX-add-USB-host-clock-enable-delay.patch @@ -0,0 +1,28 @@ +From 80a2f983e9f44dbc3e01ae31c62d877846a7f791 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:19 +0100 +Subject: [PATCH 01/11] MIPS: BCM63XX: add USB host clock enable delay + +Knowledge of the clock setup delay should remain at the clock level (so +it can be clock specific and CPU specific). Add the 100 milliseconds +required clock delay for the USB host clock when it gets enabled. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/clk.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -177,6 +177,11 @@ static void usbh_set(struct clk *clk, in + bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); + else if (BCMCPU_IS_6368()) + bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); ++ else ++ return; ++ ++ if (enable) ++ msleep(100); + } + + static struct clk clk_usbh = { diff --git a/target/linux/brcm63xx/patches-3.18/101-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch b/target/linux/brcm63xx/patches-3.18/101-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch new file mode 100644 index 0000000000..5b2c03f62d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/101-MIPS-BCM63XX-add-USB-device-clock-enable-delay-to-cl.patch @@ -0,0 +1,41 @@ +From 8e9bf528a122741f0171b89c297b63041116d704 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:20 +0100 +Subject: [PATCH 02/11] MIPS: BCM63XX: add USB device clock enable delay to + clock code + +This patch adds the required 10 micro seconds delay to the USB device +clock enable operation. Put this where the correct clock knowledege is, +which is in the clock code, and remove this delay from the bcm63xx_udc +gadget driver where it was before. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/clk.c | 5 +++++ + drivers/usb/gadget/bcm63xx_udc.c | 1 - + 2 files changed, 5 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -199,6 +199,11 @@ static void usbd_set(struct clk *clk, in + bcm_hwclock_set(CKCTL_6362_USBD_EN, enable); + else if (BCMCPU_IS_6368()) + bcm_hwclock_set(CKCTL_6368_USBD_EN, enable); ++ else ++ return; ++ ++ if (enable) ++ udelay(10); + } + + static struct clk clk_usbd = { +--- a/drivers/usb/gadget/udc/bcm63xx_udc.c ++++ b/drivers/usb/gadget/udc/bcm63xx_udc.c +@@ -391,7 +391,6 @@ static inline void set_clocks(struct bcm + if (is_enabled) { + clk_enable(udc->usbh_clk); + clk_enable(udc->usbd_clk); +- udelay(10); + } else { + clk_disable(udc->usbd_clk); + clk_disable(udc->usbh_clk); diff --git a/target/linux/brcm63xx/patches-3.18/102-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch b/target/linux/brcm63xx/patches-3.18/102-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch new file mode 100644 index 0000000000..5d106f81b2 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/102-MIPS-BCM63XX-move-code-touching-the-USB-private-regi.patch @@ -0,0 +1,151 @@ +From ac9b0b574d54be28b300bf99ffe092a2c589484f Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:21 +0100 +Subject: [PATCH 03/11] MIPS: BCM63XX: move code touching the USB private + register + +This patch moves the code touching the USB private register in the +bcm63xx USB gadget driver to arch/mips/bcm63xx/usb-common.c in +preparation for adding support for OHCI and EHCI host controllers which +will also touch the USB private register. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/Makefile | 2 +- + arch/mips/bcm63xx/usb-common.c | 53 ++++++++++++++++++++ + .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 9 ++++ + drivers/usb/gadget/bcm63xx_udc.c | 27 ++-------- + 4 files changed, 67 insertions(+), 24 deletions(-) + create mode 100644 arch/mips/bcm63xx/usb-common.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -1,7 +1,7 @@ + obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ +- dev-wdt.o dev-usb-usbd.o ++ dev-wdt.o dev-usb-usbd.o usb-common.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- /dev/null ++++ b/arch/mips/bcm63xx/usb-common.c +@@ -0,0 +1,53 @@ ++/* ++ * Broadcom BCM63xx common USB device configuration code ++ * ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com> ++ * Copyright (C) 2012 Broadcom Corporation ++ * ++ */ ++#include <linux/export.h> ++ ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_regs.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_usb_priv.h> ++ ++void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device) ++{ ++ u32 val; ++ ++ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); ++ if (is_device) { ++ val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); ++ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); ++ } else { ++ val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); ++ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); ++ } ++ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); ++ ++ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); ++ if (is_device) ++ val |= USBH_PRIV_SWAP_USBD_MASK; ++ else ++ val &= ~USBH_PRIV_SWAP_USBD_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); ++} ++EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode); ++ ++void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on) ++{ ++ u32 val; ++ ++ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); ++ if (is_on) ++ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); ++ else ++ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); ++ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); ++} ++EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup); +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h +@@ -0,0 +1,9 @@ ++#ifndef BCM63XX_USB_PRIV_H_ ++#define BCM63XX_USB_PRIV_H_ ++ ++#include <linux/types.h> ++ ++void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device); ++void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on); ++ ++#endif /* BCM63XX_USB_PRIV_H_ */ +--- a/drivers/usb/gadget/udc/bcm63xx_udc.c ++++ b/drivers/usb/gadget/udc/bcm63xx_udc.c +@@ -40,6 +40,7 @@ + #include <bcm63xx_dev_usb_usbd.h> + #include <bcm63xx_io.h> + #include <bcm63xx_regs.h> ++#include <bcm63xx_usb_priv.h> + + #define DRV_MODULE_NAME "bcm63xx_udc" + +@@ -868,22 +869,7 @@ static void bcm63xx_select_phy_mode(stru + bcm_gpio_writel(val, GPIO_PINMUX_OTHR_REG); + } + +- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); +- if (is_device) { +- val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); +- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); +- } else { +- val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT); +- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); +- } +- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); +- +- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); +- if (is_device) +- val |= USBH_PRIV_SWAP_USBD_MASK; +- else +- val &= ~USBH_PRIV_SWAP_USBD_MASK; +- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); ++ bcm63xx_usb_priv_select_phy_mode(portmask, is_device); + } + + /** +@@ -897,14 +883,9 @@ static void bcm63xx_select_phy_mode(stru + */ + static void bcm63xx_select_pullup(struct bcm63xx_udc *udc, bool is_on) + { +- u32 val, portmask = BIT(udc->pd->port_no); ++ u32 portmask = BIT(udc->pd->port_no); + +- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); +- if (is_on) +- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); +- else +- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); +- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); ++ bcm63xx_usb_priv_select_pullup(portmask, is_on); + } + + /** diff --git a/target/linux/brcm63xx/patches-3.18/103-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch b/target/linux/brcm63xx/patches-3.18/103-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch new file mode 100644 index 0000000000..40bbe083a7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/103-MIPS-BCM63XX-add-OHCI-EHCI-configuration-bits-to-com.patch @@ -0,0 +1,169 @@ +From 28758a9da77954ed323f86123ef448c6a563c037 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:22 +0100 +Subject: [PATCH 04/11] MIPS: BCM63XX: add OHCI/EHCI configuration bits to + common USB code + +This patch updates the common USB code touching the USB private +registers with the specific bits to properly enable OHCI and EHCI +controllers on BCM63xx SoCs. As a result we now need to protect access +to Read Modify Write sequences using a spinlock because we cannot +guarantee that any of the exposed helper will not be called +concurrently. + +Signed-off-by: Maxime Bizon <mbizon@freebox.fr> +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/usb-common.c | 97 ++++++++++++++++++++ + .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 2 + + 2 files changed, 99 insertions(+) + +--- a/arch/mips/bcm63xx/usb-common.c ++++ b/arch/mips/bcm63xx/usb-common.c +@@ -5,10 +5,12 @@ + * License. See the file "COPYING" in the main directory of this archive + * for more details. + * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> + * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com> + * Copyright (C) 2012 Broadcom Corporation + * + */ ++#include <linux/spinlock.h> + #include <linux/export.h> + + #include <bcm63xx_cpu.h> +@@ -16,9 +18,14 @@ + #include <bcm63xx_io.h> + #include <bcm63xx_usb_priv.h> + ++static DEFINE_SPINLOCK(usb_priv_reg_lock); ++ + void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device) + { + u32 val; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&usb_priv_reg_lock, flags); + + val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); + if (is_device) { +@@ -36,12 +43,17 @@ void bcm63xx_usb_priv_select_phy_mode(u3 + else + val &= ~USBH_PRIV_SWAP_USBD_MASK; + bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG); ++ ++ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); + } + EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode); + + void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on) + { + u32 val; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&usb_priv_reg_lock, flags); + + val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG); + if (is_on) +@@ -49,5 +61,90 @@ void bcm63xx_usb_priv_select_pullup(u32 + else + val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT); + bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG); ++ ++ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); + } + EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup); ++ ++/* The following array represents the meaning of the DESC/DATA ++ * endian swapping with respect to the CPU configured endianness ++ * ++ * DATA ENDN mmio descriptor ++ * 0 0 BE invalid ++ * 0 1 BE LE ++ * 1 0 BE BE ++ * 1 1 BE invalid ++ * ++ * Since BCM63XX SoCs are configured to be in big-endian mode ++ * we want configuration at line 3. ++ */ ++void bcm63xx_usb_priv_ohci_cfg_set(void) ++{ ++ u32 reg; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&usb_priv_reg_lock, flags); ++ ++ if (BCMCPU_IS_6348()) ++ bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG); ++ else if (BCMCPU_IS_6358()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); ++ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); ++ /* ++ * The magic value comes for the original vendor BSP ++ * and is needed for USB to work. Datasheet does not ++ * help, so the magic value is used as-is. ++ */ ++ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, ++ USBH_PRIV_TEST_6358_REG); ++ ++ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); ++ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } ++ ++ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); ++} ++ ++void bcm63xx_usb_priv_ehci_cfg_set(void) ++{ ++ u32 reg; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&usb_priv_reg_lock, flags); ++ ++ if (BCMCPU_IS_6358()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG); ++ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG); ++ ++ /* ++ * The magic value comes for the original vendor BSP ++ * and is needed for USB to work. Datasheet does not ++ * help, so the magic value is used as-is. ++ */ ++ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020, ++ USBH_PRIV_TEST_6358_REG); ++ ++ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); ++ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } ++ ++ spin_unlock_irqrestore(&usb_priv_reg_lock, flags); ++} +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h +@@ -5,5 +5,7 @@ + + void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device); + void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on); ++void bcm63xx_usb_priv_ohci_cfg_set(void); ++void bcm63xx_usb_priv_ehci_cfg_set(void); + + #endif /* BCM63XX_USB_PRIV_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/104-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch b/target/linux/brcm63xx/patches-3.18/104-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch new file mode 100644 index 0000000000..768dccac5e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/104-MIPS-BCM63XX-introduce-BCM63XX_OHCI-configuration-sy.patch @@ -0,0 +1,62 @@ +From 94ec618bd1a6b07fafbbfc9bcc54e7f9360ff9a0 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:23 +0100 +Subject: [PATCH 05/11] MIPS: BCM63XX: introduce BCM63XX_OHCI configuration + symbol + +This configuration symbol can be used by CPUs supporting the on-chip +OHCI controller, and ensures that all relevant OHCI-related +configuration options are correctly selected. So far, OHCI support is +available for the 6328, 6348, 6358 and 6358 SoCs. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/Kconfig | 15 ++++++++++----- + 1 file changed, 10 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -6,10 +6,17 @@ config BCM63XX_CPU_3368 + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI + ++config BCM63XX_OHCI ++ bool ++ select USB_ARCH_HAS_OHCI ++ select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD ++ select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD ++ + config BCM63XX_CPU_6328 + bool "support 6328 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI ++ select BCM63XX_OHCI + + config BCM63XX_CPU_6338 + bool "support 6338 CPU" +@@ -24,21 +31,25 @@ config BCM63XX_CPU_6348 + bool "support 6348 CPU" + select SYS_HAS_CPU_BMIPS32_3300 + select HW_HAS_PCI ++ select BCM63XX_OHCI + + config BCM63XX_CPU_6358 + bool "support 6358 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI ++ select BCM63XX_OHCI + + config BCM63XX_CPU_6362 + bool "support 6362 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI ++ select BCM63XX_OHCI + + config BCM63XX_CPU_6368 + bool "support 6368 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI ++ select BCM63XX_OHCI + endmenu + + source "arch/mips/bcm63xx/boards/Kconfig" diff --git a/target/linux/brcm63xx/patches-3.18/105-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch b/target/linux/brcm63xx/patches-3.18/105-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch new file mode 100644 index 0000000000..111d481e54 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/105-MIPS-BCM63XX-add-support-for-the-on-chip-OHCI-contro.patch @@ -0,0 +1,138 @@ +From 30d22baef255c99a12c4858ce4ab0d45f0d8c9ae Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:24 +0100 +Subject: [PATCH 06/11] MIPS: BCM63XX: add support for the on-chip OHCI + controller + +Broadcom BCM63XX SoCs include an on-chip OHCI controller which can be +driven by the ohci-platform generic driver by using specific power +on/off/suspend callback to manage clocks and hardware specific +configuration. + +Signed-off-by: Maxime Bizon <mbizon@freebox.fr> +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/Makefile | 2 +- + arch/mips/bcm63xx/dev-usb-ohci.c | 94 ++++++++++++++++++++ + .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h | 6 ++ + 3 files changed, 101 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -1,7 +1,7 @@ + obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ +- dev-wdt.o dev-usb-usbd.o usb-common.o ++ dev-wdt.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- /dev/null ++++ b/arch/mips/bcm63xx/dev-usb-ohci.c +@@ -0,0 +1,94 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> ++ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org> ++ */ ++ ++#include <linux/init.h> ++#include <linux/kernel.h> ++#include <linux/platform_device.h> ++#include <linux/usb/ohci_pdriver.h> ++#include <linux/dma-mapping.h> ++#include <linux/clk.h> ++#include <linux/delay.h> ++ ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_regs.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_usb_priv.h> ++#include <bcm63xx_dev_usb_ohci.h> ++ ++static struct resource ohci_resources[] = { ++ { ++ .start = -1, /* filled at runtime */ ++ .end = -1, /* filled at runtime */ ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = -1, /* filled at runtime */ ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static u64 ohci_dmamask = DMA_BIT_MASK(32); ++ ++static struct clk *usb_host_clock; ++ ++static int bcm63xx_ohci_power_on(struct platform_device *pdev) ++{ ++ usb_host_clock = clk_get(&pdev->dev, "usbh"); ++ if (IS_ERR_OR_NULL(usb_host_clock)) ++ return -ENODEV; ++ ++ clk_prepare_enable(usb_host_clock); ++ ++ bcm63xx_usb_priv_ohci_cfg_set(); ++ ++ return 0; ++} ++ ++static void bcm63xx_ohci_power_off(struct platform_device *pdev) ++{ ++ if (!IS_ERR_OR_NULL(usb_host_clock)) { ++ clk_disable_unprepare(usb_host_clock); ++ clk_put(usb_host_clock); ++ } ++} ++ ++static struct usb_ohci_pdata bcm63xx_ohci_pdata = { ++ .big_endian_desc = 1, ++ .big_endian_mmio = 1, ++ .no_big_frame_no = 1, ++ .num_ports = 1, ++ .power_on = bcm63xx_ohci_power_on, ++ .power_off = bcm63xx_ohci_power_off, ++ .power_suspend = bcm63xx_ohci_power_off, ++}; ++ ++static struct platform_device bcm63xx_ohci_device = { ++ .name = "ohci-platform", ++ .id = -1, ++ .num_resources = ARRAY_SIZE(ohci_resources), ++ .resource = ohci_resources, ++ .dev = { ++ .platform_data = &bcm63xx_ohci_pdata, ++ .dma_mask = &ohci_dmamask, ++ .coherent_dma_mask = DMA_BIT_MASK(32), ++ }, ++}; ++ ++int __init bcm63xx_ohci_register(void) ++{ ++ if (BCMCPU_IS_6345() || BCMCPU_IS_6338()) ++ return -ENODEV; ++ ++ ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); ++ ohci_resources[0].end = ohci_resources[0].start; ++ ohci_resources[0].end += RSET_OHCI_SIZE - 1; ++ ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0); ++ ++ return platform_device_register(&bcm63xx_ohci_device); ++} +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h +@@ -0,0 +1,6 @@ ++#ifndef BCM63XX_DEV_USB_OHCI_H_ ++#define BCM63XX_DEV_USB_OHCI_H_ ++ ++int bcm63xx_ohci_register(void); ++ ++#endif /* BCM63XX_DEV_USB_OHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/106-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch b/target/linux/brcm63xx/patches-3.18/106-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch new file mode 100644 index 0000000000..2c264829fb --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/106-MIPS-BCM63XX-register-OHCI-controller-if-board-enabl.patch @@ -0,0 +1,36 @@ +From 33ef960aed15f9a98a2c51d8d794cd72418e0be4 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:25 +0100 +Subject: [PATCH 07/11] MIPS: BCM63XX: register OHCI controller if board + enables it + +BCM63XX-based boards can control the registration of the OHCI controller +by setting their has_ohci0 flag to 1. Handle this in the generic +code dealing with board registration and call the actual helper to +register the OHCI controller. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -26,6 +26,7 @@ + #include <bcm63xx_dev_hsspi.h> + #include <bcm63xx_dev_pcmcia.h> + #include <bcm63xx_dev_spi.h> ++#include <bcm63xx_dev_usb_ohci.h> + #include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> + +@@ -898,6 +899,9 @@ int __init board_register_devices(void) + if (board.has_usbd) + bcm63xx_usbd_register(&board.usbd); + ++ if (board.has_ohci0) ++ bcm63xx_ohci_register(); ++ + if (board.has_dsp) + bcm63xx_dsp_register(&board.dsp); + diff --git a/target/linux/brcm63xx/patches-3.18/107-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch b/target/linux/brcm63xx/patches-3.18/107-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch new file mode 100644 index 0000000000..bce91e3736 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/107-MIPS-BCM63XX-introduce-BCM63XX_EHCI-configuration-sy.patch @@ -0,0 +1,62 @@ +From 00da1683364e58c6430a4577123d01037f8faddc Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:26 +0100 +Subject: [PATCH 08/11] MIPS: BCM63XX: introduce BCM63XX_EHCI configuration + symbol + +This configuration symbol can be used by CPUs supporting the on-chip +EHCI controller, and ensures that all relevant EHCI-related +configuration options are selected. So far BCM6328, BCM6358 and BCM6368 +have an EHCI controller and do select this symbol. Update +drivers/usb/host/Kconfig with BCM63XX to update direct unmet +dependencies. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/Kconfig | 9 +++++++++ + drivers/usb/host/Kconfig | 5 +++-- + 2 files changed, 12 insertions(+), 2 deletions(-) + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -12,11 +12,18 @@ config BCM63XX_OHCI + select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD + select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD + ++config BCM63XX_EHCI ++ bool ++ select USB_ARCH_HAS_EHCI ++ select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD ++ select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD ++ + config BCM63XX_CPU_6328 + bool "support 6328 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI + select BCM63XX_OHCI ++ select BCM63XX_EHCI + + config BCM63XX_CPU_6338 + bool "support 6338 CPU" +@@ -38,18 +45,21 @@ config BCM63XX_CPU_6358 + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI + select BCM63XX_OHCI ++ select BCM63XX_EHCI + + config BCM63XX_CPU_6362 + bool "support 6362 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI + select BCM63XX_OHCI ++ select BCM63XX_EHCI + + config BCM63XX_CPU_6368 + bool "support 6368 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI + select BCM63XX_OHCI ++ select BCM63XX_EHCI + endmenu + + source "arch/mips/bcm63xx/boards/Kconfig" diff --git a/target/linux/brcm63xx/patches-3.18/108-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch b/target/linux/brcm63xx/patches-3.18/108-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch new file mode 100644 index 0000000000..8b1f8d22b8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/108-MIPS-BCM63XX-add-support-for-the-on-chip-EHCI-contro.patch @@ -0,0 +1,137 @@ +From e38f13bd6408769c0b565bb1079024f496eee121 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:27 +0100 +Subject: [PATCH 09/11] MIPS: BCM63XX: add support for the on-chip EHCI + controller + +Broadcom BCM63XX SoCs include an on-chip EHCI controller which can be +driven by the generic ehci-platform driver by using specific power +on/off/suspend callbacks to manage clocks and hardware specific +configuration. + +Signed-off-by: Maxime Bizon <mbizon@freebox.fr> +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/Makefile | 2 +- + arch/mips/bcm63xx/dev-usb-ehci.c | 92 ++++++++++++++++++++ + .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h | 6 ++ + 3 files changed, 99 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -1,7 +1,8 @@ + obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \ + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ +- dev-wdt.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o ++ dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ ++ usb-common.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- /dev/null ++++ b/arch/mips/bcm63xx/dev-usb-ehci.c +@@ -0,0 +1,92 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> ++ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org> ++ */ ++ ++#include <linux/init.h> ++#include <linux/kernel.h> ++#include <linux/platform_device.h> ++#include <linux/clk.h> ++#include <linux/delay.h> ++#include <linux/usb/ehci_pdriver.h> ++#include <linux/dma-mapping.h> ++ ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_regs.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_usb_priv.h> ++#include <bcm63xx_dev_usb_ehci.h> ++ ++static struct resource ehci_resources[] = { ++ { ++ .start = -1, /* filled at runtime */ ++ .end = -1, /* filled at runtime */ ++ .flags = IORESOURCE_MEM, ++ }, ++ { ++ .start = -1, /* filled at runtime */ ++ .flags = IORESOURCE_IRQ, ++ }, ++}; ++ ++static u64 ehci_dmamask = DMA_BIT_MASK(32); ++ ++static struct clk *usb_host_clock; ++ ++static int bcm63xx_ehci_power_on(struct platform_device *pdev) ++{ ++ usb_host_clock = clk_get(&pdev->dev, "usbh"); ++ if (IS_ERR_OR_NULL(usb_host_clock)) ++ return -ENODEV; ++ ++ clk_prepare_enable(usb_host_clock); ++ ++ bcm63xx_usb_priv_ehci_cfg_set(); ++ ++ return 0; ++} ++ ++static void bcm63xx_ehci_power_off(struct platform_device *pdev) ++{ ++ if (!IS_ERR_OR_NULL(usb_host_clock)) { ++ clk_disable_unprepare(usb_host_clock); ++ clk_put(usb_host_clock); ++ } ++} ++ ++static struct usb_ehci_pdata bcm63xx_ehci_pdata = { ++ .big_endian_desc = 1, ++ .big_endian_mmio = 1, ++ .power_on = bcm63xx_ehci_power_on, ++ .power_off = bcm63xx_ehci_power_off, ++ .power_suspend = bcm63xx_ehci_power_off, ++}; ++ ++static struct platform_device bcm63xx_ehci_device = { ++ .name = "ehci-platform", ++ .id = -1, ++ .num_resources = ARRAY_SIZE(ehci_resources), ++ .resource = ehci_resources, ++ .dev = { ++ .platform_data = &bcm63xx_ehci_pdata, ++ .dma_mask = &ehci_dmamask, ++ .coherent_dma_mask = DMA_BIT_MASK(32), ++ }, ++}; ++ ++int __init bcm63xx_ehci_register(void) ++{ ++ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) ++ return 0; ++ ++ ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); ++ ehci_resources[0].end = ehci_resources[0].start; ++ ehci_resources[0].end += RSET_EHCI_SIZE - 1; ++ ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0); ++ ++ return platform_device_register(&bcm63xx_ehci_device); ++} +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h +@@ -0,0 +1,6 @@ ++#ifndef BCM63XX_DEV_USB_EHCI_H_ ++#define BCM63XX_DEV_USB_EHCI_H_ ++ ++int bcm63xx_ehci_register(void); ++ ++#endif /* BCM63XX_DEV_USB_EHCI_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/109-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch b/target/linux/brcm63xx/patches-3.18/109-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch new file mode 100644 index 0000000000..641a57c4c0 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/109-MIPS-BCM63XX-register-EHCI-controller-if-board-enabl.patch @@ -0,0 +1,36 @@ +From 709ef2034f5ba06da35f89856ad7baf2b7a41287 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:28 +0100 +Subject: [PATCH 10/11] MIPS: BCM63XX: register EHCI controller if board + enables it + +BCM63XX-based board can control the registration of the EHCI controller +by setting their has_ehci0 flag to 1. Handle this in the generic +code dealing with board registration and call the actual helper to register +the EHCI controller. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -26,6 +26,7 @@ + #include <bcm63xx_dev_hsspi.h> + #include <bcm63xx_dev_pcmcia.h> + #include <bcm63xx_dev_spi.h> ++#include <bcm63xx_dev_usb_ehci.h> + #include <bcm63xx_dev_usb_ohci.h> + #include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> +@@ -899,6 +900,9 @@ int __init board_register_devices(void) + if (board.has_usbd) + bcm63xx_usbd_register(&board.usbd); + ++ if (board.has_ehci0) ++ bcm63xx_ehci_register(); ++ + if (board.has_ohci0) + bcm63xx_ohci_register(); + diff --git a/target/linux/brcm63xx/patches-3.18/110-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch b/target/linux/brcm63xx/patches-3.18/110-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch new file mode 100644 index 0000000000..6d91129932 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/110-MIPS-BCM63XX-EHCI-controller-does-not-support-overcu.patch @@ -0,0 +1,24 @@ +From 111bbd770441ab34f9da5bb1d85767a9b75227b4 Mon Sep 17 00:00:00 2001 +From: Florian Fainelli <florian@openwrt.org> +Date: Mon, 28 Jan 2013 20:06:30 +0100 +Subject: [PATCH 12/12] MIPS: BCM63XX: EHCI controller does not support + overcurrent + +This patch sets the ignore_oc flag for the BCM63XX EHCI controller as it +does not support proper overcurrent reporting. + +Signed-off-by: Florian Fainelli <florian@openwrt.org> +--- + arch/mips/bcm63xx/dev-usb-ehci.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/mips/bcm63xx/dev-usb-ehci.c ++++ b/arch/mips/bcm63xx/dev-usb-ehci.c +@@ -61,6 +61,7 @@ static void bcm63xx_ehci_power_off(struc + static struct usb_ehci_pdata bcm63xx_ehci_pdata = { + .big_endian_desc = 1, + .big_endian_mmio = 1, ++ .ignore_oc = 1, + .power_on = bcm63xx_ehci_power_on, + .power_off = bcm63xx_ehci_power_off, + .power_suspend = bcm63xx_ehci_power_off, diff --git a/target/linux/brcm63xx/patches-3.18/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch b/target/linux/brcm63xx/patches-3.18/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch new file mode 100644 index 0000000000..00dc9c90ee --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/201-SPI-Allow-specifying-the-parsers-for-SPI-flash.patch @@ -0,0 +1,38 @@ +From 3f650fc30aa0badf9d02842ce396cea3eef2eeaa Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Fri, 1 Jul 2011 23:16:47 +0200 +Subject: [PATCH 49/79] SPI: Allow specifying the parsers for SPI flash + +Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> +--- + include/linux/spi/flash.h | 5 ++++- + 1 file changed, 4 insertions(+), 1 deletion(-) + +--- a/include/linux/spi/flash.h ++++ b/include/linux/spi/flash.h +@@ -2,7 +2,7 @@ + #define LINUX_SPI_FLASH_H + + struct mtd_partition; +- ++struct mtd_part_parser_data; + /** + * struct flash_platform_data: board-specific flash data + * @name: optional flash device name (eg, as used with mtdparts=) +@@ -10,6 +10,8 @@ struct mtd_partition; + * @nr_parts: number of mtd_partitions for static partitoning + * @type: optional flash device type (e.g. m25p80 vs m25p64), for use + * with chips that can't be queried for JEDEC or other IDs ++ * @part_probe_types: optional list of MTD parser names to use for ++ * partitioning + * + * Board init code (in arch/.../mach-xxx/board-yyy.c files) can + * provide information about SPI flash parts (such as DataFlash) to +@@ -25,6 +27,7 @@ struct flash_platform_data { + + char *type; + ++ const char **part_probe_types; + /* we'll likely add more ... use JEDEC IDs, etc */ + }; + diff --git a/target/linux/brcm63xx/patches-3.18/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch b/target/linux/brcm63xx/patches-3.18/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch new file mode 100644 index 0000000000..b94969406d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/202-MTD-DEVICES-m25p80-use-parsers-if-provided-in-flash-.patch @@ -0,0 +1,23 @@ +From c7c3c338cb25d7f55ddb3f6bfbf3572758ca3896 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Thu, 10 Nov 2011 16:53:08 +0100 +Subject: [PATCH 50/79] MTD: DEVICES: m25p80: use parsers if provided in flash + platform data + +Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> +--- + drivers/mtd/devices/m25p80.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/mtd/devices/m25p80.c ++++ b/drivers/mtd/devices/m25p80.c +@@ -246,7 +246,8 @@ static int m25p_probe(struct spi_device + + ppdata.of_node = spi->dev.of_node; + +- return mtd_device_parse_register(&flash->mtd, NULL, &ppdata, ++ return mtd_device_parse_register(&flash->mtd, ++ data ? data->part_probe_types : NULL, &ppdata, + data ? data->parts : NULL, + data ? data->nr_parts : 0); + } diff --git a/target/linux/brcm63xx/patches-3.18/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch b/target/linux/brcm63xx/patches-3.18/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch new file mode 100644 index 0000000000..740fb2dafc --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/203-MTD-DEVICES-m25p80-add-support-for-limiting-reads.patch @@ -0,0 +1,90 @@ +From 5fb4e8d7287ac8fcb33aae8b1e9e22c5a3c392bd Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Thu, 10 Nov 2011 17:33:40 +0100 +Subject: [PATCH 51/79] MTD: DEVICES: m25p80: add support for limiting reads + +Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> +--- + drivers/mtd/devices/m25p80.c | 29 +++++++++++++++++++++++++++-- + include/linux/spi/flash.h | 4 ++++ + 2 files changed, 31 insertions(+), 2 deletions(-) + +--- a/drivers/mtd/devices/m25p80.c ++++ b/drivers/mtd/devices/m25p80.c +@@ -32,6 +32,7 @@ struct m25p { + struct spi_device *spi; + struct spi_nor spi_nor; + struct mtd_info mtd; ++ int max_transfer_len; + u8 command[MAX_CMD_SIZE]; + }; + +@@ -121,7 +122,7 @@ static inline unsigned int m25p80_rx_nbi + * Read an address range from the nor chip. The address range + * may be any size provided it is within the physical boundaries. + */ +-static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, ++static int __m25p80_read(struct spi_nor *nor, loff_t from, size_t len, + size_t *retlen, u_char *buf) + { + struct m25p *flash = nor->priv; +@@ -157,6 +158,29 @@ static int m25p80_read(struct spi_nor *n + return 0; + } + ++static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len, ++ size_t *retlen, u_char *buf) ++{ ++ struct m25p *flash = nor->priv; ++ size_t off; ++ size_t read_len = flash->max_transfer_len; ++ size_t part_len; ++ int ret = 0; ++ ++ if (!read_len) ++ return __m25p80_read(nor, from, len, retlen, buf); ++ ++ *retlen = 0; ++ ++ for (off = 0; off < len && !ret; off += read_len) { ++ ret = __m25p80_read(nor, from + off, min(len - off, read_len), ++ &part_len, buf + off); ++ *retlen += part_len; ++ } ++ ++ return ret; ++} ++ + static int m25p80_erase(struct spi_nor *nor, loff_t offset) + { + struct m25p *flash = nor->priv; +@@ -240,6 +264,9 @@ static int m25p_probe(struct spi_device + else + flash_name = spi->modalias; + ++ if (data) ++ flash->max_transfer_len = data->max_transfer_len; ++ + ret = spi_nor_scan(nor, flash_name, mode); + if (ret) + return ret; +--- a/include/linux/spi/flash.h ++++ b/include/linux/spi/flash.h +@@ -13,6 +13,8 @@ struct mtd_part_parser_data; + * @part_probe_types: optional list of MTD parser names to use for + * partitioning + * ++ * @max_transfer_len: option maximum read/write length limitation for ++ * SPI controllers not able to transfer any length commands. + * Board init code (in arch/.../mach-xxx/board-yyy.c files) can + * provide information about SPI flash parts (such as DataFlash) to + * help set up the device and its appropriate default partitioning. +@@ -28,6 +30,8 @@ struct flash_platform_data { + char *type; + + const char **part_probe_types; ++ ++ unsigned int max_transfer_len; + /* we'll likely add more ... use JEDEC IDs, etc */ + }; + diff --git a/target/linux/brcm63xx/patches-3.18/204-USB-OHCI-allow-other-arches-to-use-the-BE-frame-numb.patch b/target/linux/brcm63xx/patches-3.18/204-USB-OHCI-allow-other-arches-to-use-the-BE-frame-numb.patch new file mode 100644 index 0000000000..4b3d44ab10 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/204-USB-OHCI-allow-other-arches-to-use-the-BE-frame-numb.patch @@ -0,0 +1,31 @@ +From b2f399dcd674a692a64bb3b300b77b78ae57b530 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 12 Jan 2014 16:47:35 +0100 +Subject: [PATCH] USB: OHCI: allow other arches to use the BE frame number + quirk + +Intead of guarding it with a certain PPC SoC and expanding the list +for each SoC requiring it, just guard it with USB_OHCI_BIG_ENDIAN_DESC. + +This makes it less suprising that passing no_big_frame_no = 1 for the +platform data does not do what expected (or + +Checking it for all big endian descriptor setups should not impact +performance much as USB1.1 is rather slow anyway. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + drivers/usb/host/ohci.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/usb/host/ohci.h ++++ b/drivers/usb/host/ohci.h +@@ -652,7 +652,7 @@ static inline u32 hc32_to_cpup (const st + * some big-endian SOC implementations. Same thing happens with PSW access. + */ + +-#ifdef CONFIG_PPC_MPC52xx ++#ifdef CONFIG_USB_OHCI_BIG_ENDIAN_DESC + #define big_endian_frame_no_quirk(ohci) (ohci->flags & OHCI_QUIRK_FRAME_NO) + #else + #define big_endian_frame_no_quirk(ohci) 0 diff --git a/target/linux/brcm63xx/patches-3.18/206-USB-EHCI-allow-limiting-ports-for-ehci-platform.patch b/target/linux/brcm63xx/patches-3.18/206-USB-EHCI-allow-limiting-ports-for-ehci-platform.patch new file mode 100644 index 0000000000..404bea9f58 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/206-USB-EHCI-allow-limiting-ports-for-ehci-platform.patch @@ -0,0 +1,66 @@ +From 6ac09efa8f0e189ffe7dd7b0889289de56ee44cc Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 19 Jan 2014 12:18:03 +0100 +Subject: [PATCH] USB: EHCI: allow limiting ports for ehci-platform + +In the same way as the ohci platform driver allows limiting ports, +enable the same for ehci. This prevents a mismatch in the available +ports between ehci/ohci on USB 2.0 controllers. + +This is needed if the USB host controller always reports the maximum +number of ports regardless of the number of available ports (because +one might be set to be usb device). + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + drivers/usb/host/ehci-hcd.c | 4 ++++ + drivers/usb/host/ehci-platform.c | 2 ++ + drivers/usb/host/ehci.h | 1 + + include/linux/usb/ehci_pdriver.h | 1 + + 4 files changed, 8 insertions(+) + +--- a/drivers/usb/host/ehci-hcd.c ++++ b/drivers/usb/host/ehci-hcd.c +@@ -660,6 +660,10 @@ int ehci_setup(struct usb_hcd *hcd) + + /* cache this readonly data; minimize chip reads */ + ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); ++ if (ehci->num_ports) { ++ ehci->hcs_params &= ~0xf; /* bits 3:0, ports on HC */ ++ ehci->hcs_params |= ehci->num_ports; ++ } + + ehci->sbrn = HCD_USB2; + +--- a/drivers/usb/host/ehci-platform.c ++++ b/drivers/usb/host/ehci-platform.c +@@ -58,6 +58,9 @@ static int ehci_platform_reset(struct us + hcd->has_tt = pdata->has_tt; + ehci->has_synopsys_hc_bug = pdata->has_synopsys_hc_bug; + ++ if (pdata->num_ports && pdata->num_ports <= 15) ++ ehci->num_ports = pdata->num_ports; ++ + if (pdata->pre_setup) { + retval = pdata->pre_setup(hcd); + if (retval < 0) +--- a/drivers/usb/host/ehci.h ++++ b/drivers/usb/host/ehci.h +@@ -213,6 +213,7 @@ struct ehci_hcd { /* one per controlle + u32 command; + + /* SILICON QUIRKS */ ++ unsigned int num_ports; + unsigned no_selective_suspend:1; + unsigned has_fsl_port_bug:1; /* FreeScale */ + unsigned big_endian_mmio:1; +--- a/include/linux/usb/ehci_pdriver.h ++++ b/include/linux/usb/ehci_pdriver.h +@@ -40,6 +40,7 @@ struct usb_hcd; + */ + struct usb_ehci_pdata { + int caps_offset; ++ unsigned int num_ports; + unsigned has_tt:1; + unsigned has_synopsys_hc_bug:1; + unsigned big_endian_desc:1; diff --git a/target/linux/brcm63xx/patches-3.18/207-MIPS-BCM63XX-move-device-registration-code-into-its-.patch b/target/linux/brcm63xx/patches-3.18/207-MIPS-BCM63XX-move-device-registration-code-into-its-.patch new file mode 100644 index 0000000000..4e5e6117b1 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/207-MIPS-BCM63XX-move-device-registration-code-into-its-.patch @@ -0,0 +1,493 @@ +From 5a50cb0d53344a2429831b00925d6183d4d332e1 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Mar 2014 03:54:05 +0100 +Subject: [PATCH 40/44] MIPS: BCM63XX: move device registration code into its + own file + +Move device registration code into its own file to allow sharing it +between board implementations. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/Makefile | 1 + + arch/mips/bcm63xx/boards/board_bcm963xx.c | 188 +------------------------- + arch/mips/bcm63xx/boards/board_common.c | 215 ++++++++++++++++++++++++++++++ + arch/mips/bcm63xx/boards/board_common.h | 8 ++ + 4 files changed, 223 insertions(+), 183 deletions(-) + create mode 100644 arch/mips/bcm63xx/boards/board_common.c + create mode 100644 arch/mips/bcm63xx/boards/board_common.h + +--- a/arch/mips/bcm63xx/boards/Makefile ++++ b/arch/mips/bcm63xx/boards/Makefile +@@ -1 +1,2 @@ ++obj-y += board_common.o + obj-$(CONFIG_BOARD_BCM963XX) += board_bcm963xx.o +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -10,35 +10,22 @@ + #include <linux/init.h> + #include <linux/kernel.h> + #include <linux/string.h> +-#include <linux/platform_device.h> +-#include <linux/ssb/ssb.h> + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +-#include <bcm63xx_dev_uart.h> + #include <bcm63xx_regs.h> + #include <bcm63xx_io.h> + #include <bcm63xx_nvram.h> +-#include <bcm63xx_dev_pci.h> +-#include <bcm63xx_dev_enet.h> +-#include <bcm63xx_dev_dsp.h> +-#include <bcm63xx_dev_flash.h> +-#include <bcm63xx_dev_hsspi.h> +-#include <bcm63xx_dev_pcmcia.h> +-#include <bcm63xx_dev_spi.h> +-#include <bcm63xx_dev_usb_ehci.h> +-#include <bcm63xx_dev_usb_ohci.h> +-#include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> + ++#include "board_common.h" ++ + #include <uapi/linux/bcm933xx_hcs.h> + + #define PFX "board_bcm963xx: " + + #define HCS_OFFSET_128K 0x20000 + +-static struct board_info board; +- + /* + * known 3368 boards + */ +@@ -711,52 +698,6 @@ static const struct board_info __initcon + }; + + /* +- * Register a sane SPROMv2 to make the on-board +- * bcm4318 WLAN work +- */ +-#ifdef CONFIG_SSB_PCIHOST +-static struct ssb_sprom bcm63xx_sprom = { +- .revision = 0x02, +- .board_rev = 0x17, +- .country_code = 0x0, +- .ant_available_bg = 0x3, +- .pa0b0 = 0x15ae, +- .pa0b1 = 0xfa85, +- .pa0b2 = 0xfe8d, +- .pa1b0 = 0xffff, +- .pa1b1 = 0xffff, +- .pa1b2 = 0xffff, +- .gpio0 = 0xff, +- .gpio1 = 0xff, +- .gpio2 = 0xff, +- .gpio3 = 0xff, +- .maxpwr_bg = 0x004c, +- .itssi_bg = 0x00, +- .boardflags_lo = 0x2848, +- .boardflags_hi = 0x0000, +-}; +- +-int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) +-{ +- if (bus->bustype == SSB_BUSTYPE_PCI) { +- memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); +- return 0; +- } else { +- printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); +- return -EINVAL; +- } +-} +-#endif +- +-/* +- * return board name for /proc/cpuinfo +- */ +-const char *board_get_name(void) +-{ +- return board.name; +-} +- +-/* + * early init callback, read nvram data from flash and checksum it + */ + void __init board_prom_init(void) +@@ -801,141 +742,16 @@ void __init board_prom_init(void) + if (strncmp(board_name, bcm963xx_boards[i]->name, 16)) + continue; + /* copy, board desc array is marked initdata */ +- memcpy(&board, bcm963xx_boards[i], sizeof(board)); ++ board_early_setup(bcm963xx_boards[i]); + break; + } + +- /* bail out if board is not found, will complain later */ +- if (!board.name[0]) { ++ /* warn if board is not found, will complain later */ ++ if (i == ARRAY_SIZE(bcm963xx_boards)) { + char name[17]; + memcpy(name, board_name, 16); + name[16] = 0; + printk(KERN_ERR PFX "unknown bcm963xx board: %s\n", + name); +- return; +- } +- +- /* setup pin multiplexing depending on board enabled device, +- * this has to be done this early since PCI init is done +- * inside arch_initcall */ +- val = 0; +- +-#ifdef CONFIG_PCI +- if (board.has_pci) { +- bcm63xx_pci_enabled = 1; +- if (BCMCPU_IS_6348()) +- val |= GPIO_MODE_6348_G2_PCI; +- } +-#endif +- +- if (board.has_pccard) { +- if (BCMCPU_IS_6348()) +- val |= GPIO_MODE_6348_G1_MII_PCCARD; +- } +- +- if (board.has_enet0 && !board.enet0.use_internal_phy) { +- if (BCMCPU_IS_6348()) +- val |= GPIO_MODE_6348_G3_EXT_MII | +- GPIO_MODE_6348_G0_EXT_MII; +- } +- +- if (board.has_enet1 && !board.enet1.use_internal_phy) { +- if (BCMCPU_IS_6348()) +- val |= GPIO_MODE_6348_G3_EXT_MII | +- GPIO_MODE_6348_G0_EXT_MII; +- } +- +- bcm_gpio_writel(val, GPIO_MODE_REG); +-} +- +-/* +- * second stage init callback, good time to panic if we couldn't +- * identify on which board we're running since early printk is working +- */ +-void __init board_setup(void) +-{ +- if (!board.name[0]) +- panic("unable to detect bcm963xx board"); +- printk(KERN_INFO PFX "board name: %s\n", board.name); +- +- /* make sure we're running on expected cpu */ +- if (bcm63xx_get_cpu_id() != board.expected_cpu_id) +- panic("unexpected CPU for bcm963xx board"); +-} +- +-static struct gpio_led_platform_data bcm63xx_led_data; +- +-static struct platform_device bcm63xx_gpio_leds = { +- .name = "leds-gpio", +- .id = 0, +- .dev.platform_data = &bcm63xx_led_data, +-}; +- +-/* +- * third stage init callback, register all board devices. +- */ +-int __init board_register_devices(void) +-{ +- if (board.has_uart0) +- bcm63xx_uart_register(0); +- +- if (board.has_uart1) +- bcm63xx_uart_register(1); +- +- if (board.has_pccard) +- bcm63xx_pcmcia_register(); +- +- if (board.has_enet0 && +- !bcm63xx_nvram_get_mac_address(board.enet0.mac_addr)) +- bcm63xx_enet_register(0, &board.enet0); +- +- if (board.has_enet1 && +- !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr)) +- bcm63xx_enet_register(1, &board.enet1); +- +- if (board.has_enetsw && +- !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr)) +- bcm63xx_enetsw_register(&board.enetsw); +- +- if (board.has_usbd) +- bcm63xx_usbd_register(&board.usbd); +- +- if (board.has_ehci0) +- bcm63xx_ehci_register(); +- +- if (board.has_ohci0) +- bcm63xx_ohci_register(); +- +- if (board.has_dsp) +- bcm63xx_dsp_register(&board.dsp); +- +- /* Generate MAC address for WLAN and register our SPROM, +- * do this after registering enet devices +- */ +-#ifdef CONFIG_SSB_PCIHOST +- if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { +- memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); +- memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); +- if (ssb_arch_register_fallback_sprom( +- &bcm63xx_get_fallback_sprom) < 0) +- pr_err(PFX "failed to register fallback SPROM\n"); + } +-#endif +- +- bcm63xx_spi_register(); +- +- bcm63xx_hsspi_register(); +- +- bcm63xx_flash_register(); +- +- bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds); +- bcm63xx_led_data.leds = board.leds; +- +- platform_device_register(&bcm63xx_gpio_leds); +- +- if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags) +- gpio_request_one(board.ephy_reset_gpio, +- board.ephy_reset_gpio_flags, "ephy-reset"); +- +- return 0; + } +--- /dev/null ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -0,0 +1,217 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> ++ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org> ++ */ ++ ++#include <linux/init.h> ++#include <linux/kernel.h> ++#include <linux/string.h> ++#include <linux/platform_device.h> ++#include <linux/ssb/ssb.h> ++#include <asm/addrspace.h> ++#include <bcm63xx_board.h> ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_dev_uart.h> ++#include <bcm63xx_regs.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_nvram.h> ++#include <bcm63xx_dev_pci.h> ++#include <bcm63xx_dev_enet.h> ++#include <bcm63xx_dev_dsp.h> ++#include <bcm63xx_dev_flash.h> ++#include <bcm63xx_dev_hsspi.h> ++#include <bcm63xx_dev_pcmcia.h> ++#include <bcm63xx_dev_spi.h> ++#include <bcm63xx_dev_usb_ehci.h> ++#include <bcm63xx_dev_usb_ohci.h> ++#include <bcm63xx_dev_usb_usbd.h> ++#include <board_bcm963xx.h> ++ ++#define PFX "board: " ++ ++static struct board_info board; ++ ++/* ++ * Register a sane SPROMv2 to make the on-board ++ * bcm4318 WLAN work ++ */ ++#ifdef CONFIG_SSB_PCIHOST ++static struct ssb_sprom bcm63xx_sprom = { ++ .revision = 0x02, ++ .board_rev = 0x17, ++ .country_code = 0x0, ++ .ant_available_bg = 0x3, ++ .pa0b0 = 0x15ae, ++ .pa0b1 = 0xfa85, ++ .pa0b2 = 0xfe8d, ++ .pa1b0 = 0xffff, ++ .pa1b1 = 0xffff, ++ .pa1b2 = 0xffff, ++ .gpio0 = 0xff, ++ .gpio1 = 0xff, ++ .gpio2 = 0xff, ++ .gpio3 = 0xff, ++ .maxpwr_bg = 0x004c, ++ .itssi_bg = 0x00, ++ .boardflags_lo = 0x2848, ++ .boardflags_hi = 0x0000, ++}; ++ ++int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) ++{ ++ if (bus->bustype == SSB_BUSTYPE_PCI) { ++ memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); ++ return 0; ++ } else { ++ printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); ++ return -EINVAL; ++ } ++} ++#endif ++ ++/* ++ * return board name for /proc/cpuinfo ++ */ ++const char *board_get_name(void) ++{ ++ return board.name; ++} ++ ++/* ++ * setup board for device registration ++ */ ++void __init board_early_setup(const struct board_info *target) ++{ ++ u32 val; ++ ++ memcpy(&board, target, sizeof(board)); ++ ++ /* setup pin multiplexing depending on board enabled device, ++ * this has to be done this early since PCI init is done ++ * inside arch_initcall */ ++ val = 0; ++ ++#ifdef CONFIG_PCI ++ if (board.has_pci) { ++ bcm63xx_pci_enabled = 1; ++ if (BCMCPU_IS_6348()) ++ val |= GPIO_MODE_6348_G2_PCI; ++ } ++#endif ++ ++ if (board.has_pccard) { ++ if (BCMCPU_IS_6348()) ++ val |= GPIO_MODE_6348_G1_MII_PCCARD; ++ } ++ ++ if (board.has_enet0 && !board.enet0.use_internal_phy) { ++ if (BCMCPU_IS_6348()) ++ val |= GPIO_MODE_6348_G3_EXT_MII | ++ GPIO_MODE_6348_G0_EXT_MII; ++ } ++ ++ if (board.has_enet1 && !board.enet1.use_internal_phy) { ++ if (BCMCPU_IS_6348()) ++ val |= GPIO_MODE_6348_G3_EXT_MII | ++ GPIO_MODE_6348_G0_EXT_MII; ++ } ++ ++ bcm_gpio_writel(val, GPIO_MODE_REG); ++} ++ ++ ++/* ++ * second stage init callback, good time to panic if we couldn't ++ * identify on which board we're running since early printk is working ++ */ ++void __init board_setup(void) ++{ ++ if (!board.name[0]) ++ panic("unable to detect bcm963xx board"); ++ printk(KERN_INFO PFX "board name: %s\n", board.name); ++ ++ /* make sure we're running on expected cpu */ ++ if (bcm63xx_get_cpu_id() != board.expected_cpu_id) ++ panic("unexpected CPU for bcm963xx board"); ++} ++ ++static struct gpio_led_platform_data bcm63xx_led_data; ++ ++static struct platform_device bcm63xx_gpio_leds = { ++ .name = "leds-gpio", ++ .id = 0, ++ .dev.platform_data = &bcm63xx_led_data, ++}; ++ ++/* ++ * third stage init callback, register all board devices. ++ */ ++int __init board_register_devices(void) ++{ ++ if (board.has_uart0) ++ bcm63xx_uart_register(0); ++ ++ if (board.has_uart1) ++ bcm63xx_uart_register(1); ++ ++ if (board.has_pccard) ++ bcm63xx_pcmcia_register(); ++ ++ if (board.has_enet0 && ++ !bcm63xx_nvram_get_mac_address(board.enet0.mac_addr)) ++ bcm63xx_enet_register(0, &board.enet0); ++ ++ if (board.has_enet1 && ++ !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr)) ++ bcm63xx_enet_register(1, &board.enet1); ++ ++ if (board.has_enetsw && ++ !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr)) ++ bcm63xx_enetsw_register(&board.enetsw); ++ ++ if (board.has_usbd) ++ bcm63xx_usbd_register(&board.usbd); ++ ++ if (board.has_ehci0) ++ bcm63xx_ehci_register(); ++ ++ if (board.has_ohci0) ++ bcm63xx_ohci_register(); ++ ++ if (board.has_dsp) ++ bcm63xx_dsp_register(&board.dsp); ++ ++ /* Generate MAC address for WLAN and register our SPROM, ++ * do this after registering enet devices ++ */ ++#ifdef CONFIG_SSB_PCIHOST ++ if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { ++ memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); ++ memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); ++ if (ssb_arch_register_fallback_sprom( ++ &bcm63xx_get_fallback_sprom) < 0) ++ pr_err(PFX "failed to register fallback SPROM\n"); ++ } ++#endif ++ ++ bcm63xx_spi_register(); ++ ++ bcm63xx_hsspi_register(); ++ ++ bcm63xx_flash_register(); ++ ++ bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds); ++ bcm63xx_led_data.leds = board.leds; ++ ++ platform_device_register(&bcm63xx_gpio_leds); ++ ++ if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags) ++ gpio_request_one(board.ephy_reset_gpio, ++ board.ephy_reset_gpio_flags, "ephy-reset"); ++ ++ return 0; ++} +--- /dev/null ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -0,0 +1,8 @@ ++#ifndef __BOARD_COMMON_H ++#define __BOARD_COMMON_H ++ ++#include <board_bcm963xx.h> ++ ++void board_early_setup(const struct board_info *board); ++ ++#endif /* __BOARD_COMMON_H */ diff --git a/target/linux/brcm63xx/patches-3.18/208-MIPS-BCM63XX-pass-a-mac-addresss-allocator-to-board-.patch b/target/linux/brcm63xx/patches-3.18/208-MIPS-BCM63XX-pass-a-mac-addresss-allocator-to-board-.patch new file mode 100644 index 0000000000..877030f866 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/208-MIPS-BCM63XX-pass-a-mac-addresss-allocator-to-board-.patch @@ -0,0 +1,100 @@ +From 4e9c34a37bd3442b286ba55441bfe22c1ac5b65f Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Mar 2014 04:08:06 +0100 +Subject: [PATCH 41/44] MIPS: BCM63XX: pass a mac addresss allocator to board + setup + +Pass a mac address allocator to board setup code to allow board +implementations to work with third party bootloaders not using nvram +for configuration storage. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 3 ++- + arch/mips/bcm63xx/boards/board_common.c | 16 ++++++++++------ + arch/mips/bcm63xx/boards/board_common.h | 3 ++- + 3 files changed, 14 insertions(+), 8 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -742,7 +742,8 @@ void __init board_prom_init(void) + if (strncmp(board_name, bcm963xx_boards[i]->name, 16)) + continue; + /* copy, board desc array is marked initdata */ +- board_early_setup(bcm963xx_boards[i]); ++ board_early_setup(bcm963xx_boards[i], ++ bcm63xx_nvram_get_mac_address); + break; + } + +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -18,7 +18,6 @@ + #include <bcm63xx_dev_uart.h> + #include <bcm63xx_regs.h> + #include <bcm63xx_io.h> +-#include <bcm63xx_nvram.h> + #include <bcm63xx_dev_pci.h> + #include <bcm63xx_dev_enet.h> + #include <bcm63xx_dev_dsp.h> +@@ -81,15 +80,20 @@ const char *board_get_name(void) + return board.name; + } + ++static int (*board_get_mac_address)(u8 mac[ETH_ALEN]); ++ + /* + * setup board for device registration + */ +-void __init board_early_setup(const struct board_info *target) ++void __init board_early_setup(const struct board_info *target, ++ int (*get_mac_address)(u8 mac[ETH_ALEN])) + { + u32 val; + + memcpy(&board, target, sizeof(board)); + ++ board_get_mac_address = get_mac_address; ++ + /* setup pin multiplexing depending on board enabled device, + * this has to be done this early since PCI init is done + * inside arch_initcall */ +@@ -162,15 +166,15 @@ int __init board_register_devices(void) + bcm63xx_pcmcia_register(); + + if (board.has_enet0 && +- !bcm63xx_nvram_get_mac_address(board.enet0.mac_addr)) ++ !board_get_mac_address(board.enet0.mac_addr)) + bcm63xx_enet_register(0, &board.enet0); + + if (board.has_enet1 && +- !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr)) ++ !board_get_mac_address(board.enet1.mac_addr)) + bcm63xx_enet_register(1, &board.enet1); + + if (board.has_enetsw && +- !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr)) ++ !board_get_mac_address(board.enetsw.mac_addr)) + bcm63xx_enetsw_register(&board.enetsw); + + if (board.has_usbd) +@@ -189,7 +193,7 @@ int __init board_register_devices(void) + * do this after registering enet devices + */ + #ifdef CONFIG_SSB_PCIHOST +- if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) { ++ if (!board_get_mac_address(bcm63xx_sprom.il0mac)) { + memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); + memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); + if (ssb_arch_register_fallback_sprom( +--- a/arch/mips/bcm63xx/boards/board_common.h ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -3,6 +3,7 @@ + + #include <board_bcm963xx.h> + +-void board_early_setup(const struct board_info *board); ++void board_early_setup(const struct board_info *board, ++ int (*get_mac_address)(u8 mac[ETH_ALEN])); + + #endif /* __BOARD_COMMON_H */ diff --git a/target/linux/brcm63xx/patches-3.18/300-reset_buttons.patch b/target/linux/brcm63xx/patches-3.18/300-reset_buttons.patch new file mode 100644 index 0000000000..c64d405496 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/300-reset_buttons.patch @@ -0,0 +1,135 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -10,6 +10,8 @@ + #include <linux/init.h> + #include <linux/kernel.h> + #include <linux/string.h> ++#include <linux/gpio_keys.h> ++#include <linux/input.h> + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +@@ -26,6 +28,9 @@ + + #define HCS_OFFSET_128K 0x20000 + ++#define BCM963XX_KEYS_POLL_INTERVAL 20 ++#define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) ++ + /* + * known 3368 boards + */ +@@ -367,6 +372,16 @@ static struct board_info __initdata boar + .active_low = 1, + }, + }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, + }; + + static struct board_info __initdata board_96348gw = { +@@ -425,6 +440,16 @@ static struct board_info __initdata boar + .active_low = 1, + }, + }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 36, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, + }; + + static struct board_info __initdata board_FAST2404 = { +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -12,6 +12,7 @@ + #include <linux/string.h> + #include <linux/platform_device.h> + #include <linux/ssb/ssb.h> ++#include <linux/gpio_keys.h> + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +@@ -32,6 +33,8 @@ + + #define PFX "board: " + ++#define BCM963XX_KEYS_POLL_INTERVAL 20 ++ + static struct board_info board; + + /* +@@ -151,11 +154,23 @@ static struct platform_device bcm63xx_gp + .dev.platform_data = &bcm63xx_led_data, + }; + ++static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = { ++ .poll_interval = BCM963XX_KEYS_POLL_INTERVAL, ++}; ++ ++static struct platform_device bcm63xx_gpio_keys_device = { ++ .name = "gpio-keys-polled", ++ .id = 0, ++ .dev.platform_data = &bcm63xx_gpio_keys_data, ++}; ++ + /* + * third stage init callback, register all board devices. + */ + int __init board_register_devices(void) + { ++ int button_count = 0; ++ + if (board.has_uart0) + bcm63xx_uart_register(0); + +@@ -217,5 +232,16 @@ int __init board_register_devices(void) + gpio_request_one(board.ephy_reset_gpio, + board.ephy_reset_gpio_flags, "ephy-reset"); + ++ /* count number of BUTTONs defined by this device */ ++ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc) ++ button_count++; ++ ++ if (button_count) { ++ bcm63xx_gpio_keys_data.nbuttons = button_count; ++ bcm63xx_gpio_keys_data.buttons = board.buttons; ++ ++ platform_device_register(&bcm63xx_gpio_keys_device); ++ } ++ + return 0; + } +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -3,6 +3,7 @@ + + #include <linux/types.h> + #include <linux/gpio.h> ++#include <linux/gpio_keys.h> + #include <linux/leds.h> + #include <bcm63xx_dev_enet.h> + #include <bcm63xx_dev_usb_usbd.h> +@@ -48,6 +49,9 @@ struct board_info { + /* GPIO LEDs */ + struct gpio_led leds[5]; + ++ /* Buttons */ ++ struct gpio_keys_button buttons[4]; ++ + /* External PHY reset GPIO */ + unsigned int ephy_reset_gpio; + diff --git a/target/linux/brcm63xx/patches-3.18/301-led_count.patch b/target/linux/brcm63xx/patches-3.18/301-led_count.patch new file mode 100644 index 0000000000..49a18255d2 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/301-led_count.patch @@ -0,0 +1,41 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -170,6 +170,7 @@ static struct platform_device bcm63xx_gp + int __init board_register_devices(void) + { + int button_count = 0; ++ int led_count = 0; + + if (board.has_uart0) + bcm63xx_uart_register(0); +@@ -223,10 +224,16 @@ int __init board_register_devices(void) + + bcm63xx_flash_register(); + +- bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds); +- bcm63xx_led_data.leds = board.leds; ++ /* count number of LEDs defined by this device */ ++ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) ++ led_count++; ++ ++ if (led_count) { ++ bcm63xx_led_data.num_leds = led_count; ++ bcm63xx_led_data.leds = board.leds; + +- platform_device_register(&bcm63xx_gpio_leds); ++ platform_device_register(&bcm63xx_gpio_leds); ++ } + + if (board.ephy_reset_gpio && board.ephy_reset_gpio_flags) + gpio_request_one(board.ephy_reset_gpio, +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -47,7 +47,7 @@ struct board_info { + struct bcm63xx_dsp_platform_data dsp; + + /* GPIO LEDs */ +- struct gpio_led leds[5]; ++ struct gpio_led leds[14]; + + /* Buttons */ + struct gpio_keys_button buttons[4]; diff --git a/target/linux/brcm63xx/patches-3.18/302-extended-platform-devices.patch b/target/linux/brcm63xx/patches-3.18/302-extended-platform-devices.patch new file mode 100644 index 0000000000..cc61cee477 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/302-extended-platform-devices.patch @@ -0,0 +1,25 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -222,6 +222,9 @@ int __init board_register_devices(void) + + bcm63xx_hsspi_register(); + ++ if (board.num_devs) ++ platform_add_devices(board.devs, board.num_devs); ++ + bcm63xx_flash_register(); + + /* count number of LEDs defined by this device */ +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -57,6 +57,10 @@ struct board_info { + + /* External PHY reset GPIO flags from gpio.h */ + unsigned long ephy_reset_gpio_flags; ++ ++ /* Additional platform devices */ ++ struct platform_device **devs; ++ unsigned int num_devs; + }; + + #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/303-spi-board-info.patch b/target/linux/brcm63xx/patches-3.18/303-spi-board-info.patch new file mode 100644 index 0000000000..878e6262d4 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/303-spi-board-info.patch @@ -0,0 +1,33 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -13,6 +13,7 @@ + #include <linux/platform_device.h> + #include <linux/ssb/ssb.h> + #include <linux/gpio_keys.h> ++#include <linux/spi/spi.h> + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +@@ -225,6 +226,9 @@ int __init board_register_devices(void) + if (board.num_devs) + platform_add_devices(board.devs, board.num_devs); + ++ if (board.num_spis) ++ spi_register_board_info(board.spis, board.num_spis); ++ + bcm63xx_flash_register(); + + /* count number of LEDs defined by this device */ +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -61,6 +61,10 @@ struct board_info { + /* Additional platform devices */ + struct platform_device **devs; + unsigned int num_devs; ++ ++ /* Additional platform devices */ ++ struct spi_board_info *spis; ++ unsigned int num_spis; + }; + + #endif /* ! BOARD_BCM963XX_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/308-board_leds_naming.patch b/target/linux/brcm63xx/patches-3.18/308-board_leds_naming.patch new file mode 100644 index 0000000000..89b7ac39e9 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/308-board_leds_naming.patch @@ -0,0 +1,267 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -130,28 +130,28 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl", ++ .name = "96338GW:green:adsl", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ses", ++ .name = "96338GW:green:ses", + .gpio = 5, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96338GW:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96338GW:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96338GW:green:stop", + .gpio = 1, + .active_low = 1, + } +@@ -171,28 +171,28 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl", ++ .name = "96338W:green:adsl", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ses", ++ .name = "96338W:green:ses", + .gpio = 5, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96338W:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96338W:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96338W:green:stop", + .gpio = 1, + .active_low = 1, + }, +@@ -231,29 +231,29 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl-fail", ++ .name = "96348R:green:adsl-fail", + .gpio = 2, + .active_low = 1, + }, + { +- .name = "ppp", ++ .name = "96348R:green:ppp", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96348R:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96348R:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + + }, + { +- .name = "stop", ++ .name = "96348R:green:stop", + .gpio = 1, + .active_low = 1, + }, +@@ -292,28 +292,28 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl-fail", ++ .name = "96348GW-10:green:adsl-fail", + .gpio = 2, + .active_low = 1, + }, + { +- .name = "ppp", ++ .name = "96348GW-10:green:ppp", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96348GW-10:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96348GW-10:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96348GW-10:green:stop", + .gpio = 1, + .active_low = 1, + }, +@@ -346,28 +346,28 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl-fail", ++ .name = "96348GW-11:green:adsl-fail", + .gpio = 2, + .active_low = 1, + }, + { +- .name = "ppp", ++ .name = "96348GW-11:green:ppp", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96348GW-11:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96348GW-11:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96348GW-11:green:stop", + .gpio = 1, + .active_low = 1, + }, +@@ -414,28 +414,28 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl-fail", ++ .name = "96348GW:green:adsl-fail", + .gpio = 2, + .active_low = 1, + }, + { +- .name = "ppp", ++ .name = "96348GW:green:ppp", + .gpio = 3, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96348GW:green:ppp-fail", + .gpio = 4, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96348GW:green:power", + .gpio = 0, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96348GW:green:stop", + .gpio = 1, + .active_low = 1, + }, +@@ -567,27 +567,27 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl-fail", ++ .name = "96358VW:green:adsl-fail", + .gpio = 15, + .active_low = 1, + }, + { +- .name = "ppp", ++ .name = "96358VW:green:ppp", + .gpio = 22, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96358VW:green:ppp-fail", + .gpio = 23, + .active_low = 1, + }, + { +- .name = "power", ++ .name = "96358VW:green:power", + .gpio = 4, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96358VW:green:stop", + .gpio = 5, + }, + }, +@@ -619,22 +619,22 @@ static struct board_info __initdata boar + + .leds = { + { +- .name = "adsl", ++ .name = "96358VW2:green:adsl", + .gpio = 22, + .active_low = 1, + }, + { +- .name = "ppp-fail", ++ .name = "96358VW2:green:ppp-fail", + .gpio = 23, + }, + { +- .name = "power", ++ .name = "96358VW2:green:power", + .gpio = 5, + .active_low = 1, + .default_trigger = "default-on", + }, + { +- .name = "stop", ++ .name = "96358VW2:green:stop", + .gpio = 4, + .active_low = 1, + }, diff --git a/target/linux/brcm63xx/patches-3.18/309-cfe_version_mod.patch b/target/linux/brcm63xx/patches-3.18/309-cfe_version_mod.patch new file mode 100644 index 0000000000..65b75e1ec8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/309-cfe_version_mod.patch @@ -0,0 +1,27 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -747,10 +747,20 @@ void __init board_prom_init(void) + + /* dump cfe version */ + cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; +- if (!memcmp(cfe, "cfe-v", 5)) +- snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u", +- cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]); +- else ++ if (strstarts(cfe, "cfe-")) { ++ if(cfe[4] == 'v') { ++ if(cfe[5] == 'd') ++ snprintf(cfe_version, 11, "%s", (char *) &cfe[5]); ++ else if (cfe[10] > 0) ++ snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u-%u", ++ cfe[5], cfe[6], cfe[7], cfe[8], cfe[9], cfe[10]); ++ else ++ snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u", ++ cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]); ++ } else { ++ snprintf(cfe_version, 12, "%s", (char *) &cfe[4]); ++ } ++ } else + strcpy(cfe_version, "unknown"); + printk(KERN_INFO PFX "CFE version: %s\n", cfe_version); + diff --git a/target/linux/brcm63xx/patches-3.18/310-cfe_simplify_detection.patch b/target/linux/brcm63xx/patches-3.18/310-cfe_simplify_detection.patch new file mode 100644 index 0000000000..e05c91d931 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/310-cfe_simplify_detection.patch @@ -0,0 +1,20 @@ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h +@@ -1,6 +1,8 @@ + #ifndef BCM63XX_BOARD_H_ + #define BCM63XX_BOARD_H_ + ++#include <asm/bootinfo.h> ++ + const char *board_get_name(void); + + void board_prom_init(void); +@@ -9,4 +11,8 @@ void board_setup(void); + + int board_register_devices(void); + ++static inline bool bcm63xx_is_cfe_present(void) { ++ return fw_arg3 == 0x43464531; ++} ++ + #endif /* ! BCM63XX_BOARD_H_ */ diff --git a/target/linux/brcm63xx/patches-3.18/311-bcm63xxpart_use_cfedetection.patch b/target/linux/brcm63xx/patches-3.18/311-bcm63xxpart_use_cfedetection.patch new file mode 100644 index 0000000000..dedd728ce9 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/311-bcm63xxpart_use_cfedetection.patch @@ -0,0 +1,51 @@ +--- a/drivers/mtd/bcm63xxpart.c ++++ b/drivers/mtd/bcm63xxpart.c +@@ -35,7 +35,7 @@ + + #include <asm/mach-bcm63xx/bcm63xx_nvram.h> + #include <linux/bcm963xx_tag.h> +-#include <asm/mach-bcm63xx/board_bcm963xx.h> ++#include <asm/mach-bcm63xx/bcm63xx_board.h> + + #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */ + +@@ -43,30 +43,6 @@ + + #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0 + +-static int bcm63xx_detect_cfe(struct mtd_info *master) +-{ +- char buf[9]; +- int ret; +- size_t retlen; +- +- ret = mtd_read(master, BCM963XX_CFE_VERSION_OFFSET, 5, &retlen, +- (void *)buf); +- buf[retlen] = 0; +- +- if (ret) +- return ret; +- +- if (strncmp("cfe-v", buf, 5) == 0) +- return 0; +- +- /* very old CFE's do not have the cfe-v string, so check for magic */ +- ret = mtd_read(master, BCM63XX_CFE_MAGIC_OFFSET, 8, &retlen, +- (void *)buf); +- buf[retlen] = 0; +- +- return strncmp("CFE1CFE1", buf, 8); +-} +- + static int bcm63xx_parse_cfe_partitions(struct mtd_info *master, + struct mtd_partition **pparts, + struct mtd_part_parser_data *data) +@@ -85,7 +61,7 @@ static int bcm63xx_parse_cfe_partitions( + u32 computed_crc; + bool rootfs_first = false; + +- if (bcm63xx_detect_cfe(master)) ++ if (!bcm63xx_is_cfe_present()) + return -EINVAL; + + cfe_erasesize = max_t(uint32_t, master->erasesize, diff --git a/target/linux/brcm63xx/patches-3.18/320-irqchip-add-support-for-bcm6345-style-l2-irq-control.patch b/target/linux/brcm63xx/patches-3.18/320-irqchip-add-support-for-bcm6345-style-l2-irq-control.patch new file mode 100644 index 0000000000..c709394b35 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/320-irqchip-add-support-for-bcm6345-style-l2-irq-control.patch @@ -0,0 +1,411 @@ +From 4d3886359d6f6ac475e143d5f3e3b389542a0510 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Nov 2014 14:53:12 +0100 +Subject: [PATCH 17/20] irqchip: add support for bcm6345-style l2 irq + controller + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + .../interrupt-controller/brcm,bcm6345-l2-intc.txt | 25 ++ + drivers/irqchip/Kconfig | 4 + + drivers/irqchip/Makefile | 1 + + drivers/irqchip/irq-bcm6345-l2.c | 320 ++++++++++++++++++++ + include/linux/irqchip/irq-bcm6345-l2-intc.h | 16 + + 5 files changed, 366 insertions(+) + create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l2-intc.txt + create mode 100644 drivers/irqchip/irq-bcm6345-l2.c + create mode 100644 include/linux/irqchip/irq-bcm6345-l2-intc.h + +--- /dev/null ++++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-l2-intc.txt +@@ -0,0 +1,25 @@ ++Broadcom BCM6345 Level 2 interrupt controller ++ ++Required properties: ++ ++- compatible: should be "brcm,bcm6345-l2-intc" ++- reg: specifies the base physical address and size of the registers; ++ multiple regs may be specified, and must match the amount of parent interrupts ++- interrupt-controller: identifies the node as an interrupt controller ++- #interrupt-cells: specifies the number of cells needed to encode an interrupt ++ source, should be 1 ++- interrupt-parent: specifies the phandle to the parent interrupt controller ++ this one is cascaded from ++- interrupts: specifies the interrupt line(s) in the interrupt-parent controller ++ node, valid values depend on the type of parent interrupt controller ++ ++Example: ++ ++periph_intc: interrupt-controller@f0406800 { ++ compatible = "brcm,bcm6345-l2-intc"; ++ interrupt-parent = <&mips_intc>; ++ #interrupt-cells = <1>; ++ reg = <0x10000020 0x10> <0x10000030 0x10>; ++ interrupt-controller; ++ interrupts = <2>, <3>; ++}; +--- a/drivers/irqchip/Kconfig ++++ b/drivers/irqchip/Kconfig +@@ -54,6 +54,10 @@ config BRCMSTB_L2_IRQ + select GENERIC_IRQ_CHIP + select IRQ_DOMAIN + ++config BCM6345_L2_IRQ ++ bool ++ select IRQ_DOMAIN ++ + config DW_APB_ICTL + bool + select IRQ_DOMAIN +--- a/drivers/irqchip/Makefile ++++ b/drivers/irqchip/Makefile +@@ -7,6 +7,7 @@ obj-$(CONFIG_ARCH_MMP) += irq-mmp.o + obj-$(CONFIG_ARCH_MVEBU) += irq-armada-370-xp.o + obj-$(CONFIG_ARCH_MXS) += irq-mxs.o + obj-$(CONFIG_ARCH_S3C24XX) += irq-s3c24xx.o ++obj-$(CONFIG_BCM6345_L2_IRQ) += irq-bcm6345-l2.o + obj-$(CONFIG_DW_APB_ICTL) += irq-dw-apb-ictl.o + obj-$(CONFIG_METAG) += irq-metag-ext.o + obj-$(CONFIG_METAG_PERFCOUNTER_IRQS) += irq-metag.o +--- /dev/null ++++ b/drivers/irqchip/irq-bcm6345-l2.c +@@ -0,0 +1,320 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2014 Jonas Gorski <jogo@openwrt.org> ++ */ ++ ++#include <linux/ioport.h> ++#include <linux/irq.h> ++#include <linux/irqchip/chained_irq.h> ++#include <linux/irqchip/irq-bcm6345-l2-intc.h> ++#include <linux/kernel.h> ++#include <linux/of.h> ++#include <linux/of_irq.h> ++#include <linux/of_address.h> ++#include <linux/slab.h> ++#include <linux/spinlock.h> ++ ++#ifdef CONFIG_BCM63XX ++#include <asm/mach-bcm63xx/bcm63xx_irq.h> ++ ++#define VIRQ_BASE IRQ_INTERNAL_BASE ++#else ++#define VIRQ_BASE 0 ++#endif ++ ++#include "irqchip.h" ++ ++#define MAX_WORDS 4 ++#define MAX_PARENT_IRQS 2 ++#define IRQS_PER_WORD 32 ++ ++struct intc_block { ++ int parent_irq; ++ void __iomem *base; ++ void __iomem *en_reg[MAX_WORDS]; ++ void __iomem *status_reg[MAX_WORDS]; ++ u32 mask_cache[MAX_WORDS]; ++}; ++ ++struct intc_data { ++ struct irq_chip chip; ++ struct intc_block block[MAX_PARENT_IRQS]; ++ ++ int num_words; ++ ++ struct irq_domain *domain; ++ spinlock_t lock; ++}; ++ ++static void bcm6345_l2_intc_irq_handle(unsigned int irq, struct irq_desc *desc) ++{ ++ struct intc_data *data = irq_desc_get_handler_data(desc); ++ struct irq_chip *chip = irq_desc_get_chip(desc); ++ struct intc_block *block; ++ unsigned int idx; ++ ++ chained_irq_enter(chip, desc); ++ ++ for (idx = 0; idx < MAX_PARENT_IRQS; idx++) ++ if (irq == data->block[idx].parent_irq) ++ block = &data->block[idx]; ++ ++ for (idx = 0; idx < data->num_words; idx++) { ++ int base = idx * IRQS_PER_WORD; ++ unsigned long pending; ++ int hw_irq; ++ ++ raw_spin_lock(data->lock); ++ pending = __raw_readl(block->en_reg[idx]) & ++ __raw_readl(block->status_reg[idx]); ++ raw_spin_unlock(data->lock); ++ ++ for_each_set_bit(hw_irq, &pending, IRQS_PER_WORD) { ++ generic_handle_irq(irq_find_mapping(data->domain, base + hw_irq)); ++ } ++ } ++ ++ chained_irq_exit(chip, desc); ++} ++ ++static void bcm6345_l2_intc_irq_mask(struct irq_data *data) ++{ ++ unsigned int i, reg, bit; ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ ++ reg = hwirq / IRQS_PER_WORD; ++ bit = hwirq % IRQS_PER_WORD; ++ ++ raw_spin_lock(priv->lock); ++ for (i = 0; i < MAX_PARENT_IRQS; i++) { ++ struct intc_block *block = &priv->block[i]; ++ u32 val; ++ ++ if (!block->parent_irq) ++ break; ++ ++ val = __raw_readl(block->en_reg[reg]); ++ __raw_writel(val & ~BIT(bit), block->en_reg[reg]); ++ } ++ raw_spin_unlock(priv->lock); ++} ++ ++static void bcm6345_l2_intc_irq_unmask(struct irq_data *data) ++{ ++ unsigned int i, reg, bit; ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ ++ reg = hwirq / IRQS_PER_WORD; ++ bit = hwirq % IRQS_PER_WORD; ++ ++ raw_spin_lock(priv->lock); ++ for (i = 0; i < MAX_PARENT_IRQS; i++) { ++ struct intc_block *block = &priv->block[i]; ++ u32 val; ++ ++ if (!block->parent_irq) ++ break; ++ ++ val = __raw_readl(block->en_reg[reg]); ++ ++ if (block->mask_cache[reg] & BIT(bit)) ++ val |= BIT(bit); ++ else ++ val &= ~BIT(bit); ++ ++ __raw_writel(val, block->en_reg[reg]); ++ ++ } ++ raw_spin_unlock(priv->lock); ++} ++ ++#ifdef CONFIG_SMP ++static int bcm6345_l2_intc_set_affinity(struct irq_data *data, ++ const struct cpumask *mask, ++ bool force) ++{ ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ struct intc_data *priv = data->domain->host_data; ++ unsigned int i, reg, bit; ++ int cpu; ++ ++ reg = hwirq / IRQS_PER_WORD; ++ bit = hwirq % IRQS_PER_WORD; ++ ++ /* we could route to more than one cpu, but performance ++ suffers, so fix it to one. ++ */ ++ cpu = cpumask_any_and(mask, cpu_online_mask); ++ if (cpu >= nr_cpu_ids) ++ return -EINVAL; ++ ++ if (cpu >= MAX_PARENT_IRQS) ++ return -EINVAL; ++ ++ if (!priv->block[cpu].parent_irq) ++ return -EINVAL; ++ ++ raw_spin_lock(priv->lock); ++ for (i = 0; i < MAX_PARENT_IRQS; i++) { ++ if (i == cpu) ++ priv->block[i].mask_cache[reg] |= BIT(bit); ++ else ++ priv->block[i].mask_cache[reg] &= ~BIT(bit); ++ } ++ raw_spin_unlock(priv->lock); ++ ++ return 0; ++} ++#endif ++ ++static int bcm6345_l2_map(struct irq_domain *d, unsigned int irq, ++ irq_hw_number_t hw) ++{ ++ struct intc_data *priv = d->host_data; ++ ++ irq_set_chip_and_handler(irq, &priv->chip, handle_level_irq); ++ ++ return 0; ++} ++ ++static const struct irq_domain_ops bcm6345_l2_domain_ops = { ++ .xlate = irq_domain_xlate_onecell, ++ .map = bcm6345_l2_map, ++}; ++ ++static int __init __bcm6345_l2_intc_init(struct device_node *node, ++ int num_blocks, int *irq, ++ void __iomem **base, int num_words) ++{ ++ struct intc_data *data; ++ unsigned int i, w, status_offset; ++ ++ data = kzalloc(sizeof(*data), GFP_KERNEL); ++ if (!data) ++ return -ENOMEM; ++ ++ status_offset = num_words * sizeof(u32); ++ ++ for (i = 0; i < num_blocks; i++) { ++ struct intc_block *block = &data->block[i]; ++ ++ block->parent_irq = irq[i]; ++ block->base = base[i]; ++ ++ for (w = 0; w < num_words; w++) { ++ int word_offset = sizeof(u32) * ((num_words - w) - 1); ++ ++ block->en_reg[w] = base[i] + word_offset; ++ block->status_reg[w] = base[i] + status_offset; ++ block->status_reg[w] += word_offset; ++ ++ /* route all interrups to line 0 by default */ ++ if (i == 0) ++ block->mask_cache[w] = 0xffffffff; ++ } ++ ++ irq_set_handler_data(block->parent_irq, data); ++ irq_set_chained_handler(block->parent_irq, ++ bcm6345_l2_intc_irq_handle); ++ } ++ ++ data->num_words = num_words; ++ ++ data->chip.name = "bcm6345-l2-intc"; ++ data->chip.irq_mask = bcm6345_l2_intc_irq_mask; ++ data->chip.irq_unmask = bcm6345_l2_intc_irq_unmask; ++ ++#ifdef CONFIG_SMP ++ if (num_blocks > 1) ++ data->chip.set_affinity = bcm6345_l2_intc_set_affinity; ++#endif ++ ++ data->domain = irq_domain_add_simple(node, IRQS_PER_WORD * num_words, ++ VIRQ_BASE, &bcm6345_l2_domain_ops, ++ data); ++ if (!data->domain) { ++ kfree(data); ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++void __init bcm6345_l2_intc_init(int num_blocks, int *irq, void __iomem **base, ++ int num_words) ++{ ++ __bcm6345_l2_intc_init(NULL, num_blocks, irq, base, num_words); ++} ++ ++#ifdef CONFIG_OF ++static int __init bcm6345_l2_intc_of_init(struct device_node *node, ++ struct device_node *parent) ++{ ++ struct resource res; ++ int num_irqs, ret = -EINVAL; ++ int irqs[MAX_PARENT_IRQS] = { 0 }; ++ void __iomem *bases[MAX_PARENT_IRQS] = { NULL }; ++ int words = 0; ++ int i; ++ ++ num_irqs = of_irq_count(node); ++ ++ if (num_irqs < 1 || num_irqs > MAX_PARENT_IRQS) ++ return -EINVAL; ++ ++ for (i = 0; i < num_irqs; i++) { ++ resource_size_t size; ++ ++ irqs[i] = irq_of_parse_and_map(node, i); ++ if (!irqs[i]) ++ goto out_unmap; ++ ++ if (of_address_to_resource(node, i, &res)) { ++ goto out_unmap; ++ } ++ ++ size = resource_size(&res); ++ switch (size) { ++ case 8: ++ case 16: ++ case 32: ++ size = size / 8; ++ break; ++ default: ++ goto out_unmap; ++ } ++ ++ if (words && words != size) { ++ ret = -EINVAL; ++ goto out_unmap; ++ } ++ words = size; ++ ++ bases[i] = of_iomap(node, i); ++ if (!bases[i]) { ++ ret = -ENOMEM; ++ goto out_unmap; ++ } ++ } ++ ++ ret = __bcm6345_l2_intc_init(node, num_irqs, irqs, bases, words); ++ if (!ret) ++ return 0; ++ ++out_unmap: ++ for (i = 0; i < num_irqs; i++) { ++ iounmap(bases[i]); ++ irq_dispose_mapping(irqs[i]); ++ } ++ ++ return ret; ++} ++ ++IRQCHIP_DECLARE(bcm6345_l2_intc, "brcm,bcm6345-l2-intc", ++ bcm6345_l2_intc_of_init); ++#endif +--- /dev/null ++++ b/include/linux/irqchip/irq-bcm6345-l2-intc.h +@@ -0,0 +1,16 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> ++ * Copyright (C) 2008 Nicolas Schichan <nschichan@freebox.fr> ++ */ ++ ++#ifndef __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_L2_INTC_H ++#define __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_L2_INTC_H ++ ++void bcm6345_l2_intc_init(int num_blocks, int *irq, void __iomem **base, ++ int num_words); ++ ++#endif /* __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_L2_INTC_H */ diff --git a/target/linux/brcm63xx/patches-3.18/321-irqchip-add-support-for-bcm6345-style-external-inter.patch b/target/linux/brcm63xx/patches-3.18/321-irqchip-add-support-for-bcm6345-style-external-inter.patch new file mode 100644 index 0000000000..8189e7e807 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/321-irqchip-add-support-for-bcm6345-style-external-inter.patch @@ -0,0 +1,384 @@ +From 6896b5f0538a7a7cfb7fac2d9ed3c6841c72ed40 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Nov 2014 14:54:27 +0100 +Subject: [PATCH 18/20] irqchip: add support for bcm6345-style external + interrupt controller + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + .../interrupt-controller/brcm,bcm6345-ext-intc.txt | 24 ++ + drivers/irqchip/Kconfig | 4 + + drivers/irqchip/Makefile | 1 + + drivers/irqchip/irq-bcm6345-ext.c | 296 ++++++++++++++++++++ + include/linux/irqchip/irq-bcm6345-ext-intc.h | 14 + + 5 files changed, 339 insertions(+) + create mode 100644 Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-ext-intc.txt + create mode 100644 drivers/irqchip/irq-bcm6345-ext.c + create mode 100644 include/linux/irqchip/irq-bcm6345-ext-intc.h + +--- /dev/null ++++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm6345-ext-intc.txt +@@ -0,0 +1,24 @@ ++Broadcom BCM6345-style external interrupt controller ++ ++Required properties: ++ ++- compatible: should be "brcm,bcm6345-l2-intc" or "brcm,bcm6345-l2-intc" ++- reg: specifies the base physical addresses and size of the registers. ++- interrupt-controller: identifies the node as an interrupt controller ++- #interrupt-cells: specifies the number of cells needed to encode an interrupt ++ source, should be 2 ++- interrupt-parent: specifies the phandle to the parent interrupt controller ++ this one is cascaded from ++- interrupts: specifies the interrupt line(s) in the interrupt-parent controller ++ node, valid values depend on the type of parent interrupt controller ++ ++Example: ++ ++ext_intc: interrupt-controller@10000018 { ++ compatible = "brcm,bcm6345-l2-intc"; ++ interrupt-parent = <&periph_intc>; ++ #interrupt-cells = <2>; ++ reg = <0x10000018 0x4>; ++ interrupt-controller; ++ interrupts = <24>, <25>, <26>, <27>; ++}; +--- a/drivers/irqchip/Kconfig ++++ b/drivers/irqchip/Kconfig +@@ -54,6 +54,10 @@ config BRCMSTB_L2_IRQ + select GENERIC_IRQ_CHIP + select IRQ_DOMAIN + ++config BCM6345_EXT_IRQ ++ bool ++ select IRQ_DOMAIN ++ + config BCM6345_L2_IRQ + bool + select IRQ_DOMAIN +--- a/drivers/irqchip/Makefile ++++ b/drivers/irqchip/Makefile +@@ -7,6 +7,7 @@ obj-$(CONFIG_ARCH_MMP) += irq-mmp.o + obj-$(CONFIG_ARCH_MVEBU) += irq-armada-370-xp.o + obj-$(CONFIG_ARCH_MXS) += irq-mxs.o + obj-$(CONFIG_ARCH_S3C24XX) += irq-s3c24xx.o ++obj-$(CONFIG_BCM6345_EXT_IRQ) += irq-bcm6345-ext.o + obj-$(CONFIG_BCM6345_L2_IRQ) += irq-bcm6345-l2.o + obj-$(CONFIG_DW_APB_ICTL) += irq-dw-apb-ictl.o + obj-$(CONFIG_METAG) += irq-metag-ext.o +--- /dev/null ++++ b/drivers/irqchip/irq-bcm6345-ext.c +@@ -0,0 +1,296 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2014 Jonas Gorski <jogo@openwrt.org> ++i */ ++ ++#include <linux/ioport.h> ++#include <linux/irq.h> ++#include <linux/irqchip/chained_irq.h> ++#include <linux/irqchip/irq-bcm6345-ext-intc.h> ++#include <linux/kernel.h> ++#include <linux/of.h> ++#include <linux/of_irq.h> ++#include <linux/of_address.h> ++#include <linux/slab.h> ++#include <linux/spinlock.h> ++ ++#include "irqchip.h" ++ ++#ifdef CONFIG_BCM63XX ++#include <asm/mach-bcm63xx/bcm63xx_irq.h> ++ ++#define VIRQ_BASE IRQ_EXTERNAL_BASE ++#else ++#define VIRQ_BASE 0 ++#endif ++ ++#define MAX_IRQS 4 ++ ++#define EXTIRQ_CFG_SENSE 0 ++#define EXTIRQ_CFG_STAT 1 ++#define EXTIRQ_CFG_CLEAR 2 ++#define EXTIRQ_CFG_MASK 3 ++#define EXTIRQ_CFG_BOTHEDGE 4 ++#define EXTIRQ_CFG_LEVELSENSE 5 ++ ++struct intc_data { ++ struct irq_chip chip; ++ struct irq_domain *domain; ++ spinlock_t lock; ++ ++ int parent_irq[MAX_IRQS]; ++ void __iomem *reg; ++ int shift; ++}; ++ ++static void bcm6345_ext_intc_irq_handle(unsigned int irq, struct irq_desc *desc) ++{ ++ struct intc_data *data = irq_desc_get_handler_data(desc); ++ struct irq_chip *chip = irq_desc_get_chip(desc); ++ unsigned int idx; ++ ++ chained_irq_enter(chip, desc); ++ ++ for (idx = 0; idx < MAX_IRQS; idx++) { ++ if (data->parent_irq[idx] != irq) ++ continue; ++ ++ generic_handle_irq(irq_find_mapping(data->domain, idx)); ++ } ++ ++ chained_irq_exit(chip, desc); ++} ++ ++static void bcm6345_ext_intc_irq_ack(struct irq_data *data) ++{ ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ u32 reg; ++ ++ raw_spin_lock(priv->lock); ++ reg = __raw_readl(priv->reg); ++ reg |= hwirq << (EXTIRQ_CFG_CLEAR * priv->shift); ++ __raw_writel(reg, priv->reg); ++ raw_spin_unlock(priv->lock); ++} ++ ++static void bcm6345_ext_intc_irq_mask(struct irq_data *data) ++{ ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ u32 reg; ++ ++ raw_spin_lock(priv->lock); ++ reg = __raw_readl(priv->reg); ++ reg &= ~(hwirq << (EXTIRQ_CFG_MASK * priv->shift)); ++ __raw_writel(reg, priv->reg); ++ raw_spin_unlock(priv->lock); ++} ++ ++static void bcm6345_ext_intc_irq_unmask(struct irq_data *data) ++{ ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ u32 reg; ++ ++ raw_spin_lock(priv->lock); ++ reg = __raw_readl(priv->reg); ++ reg |= hwirq << (EXTIRQ_CFG_MASK * priv->shift); ++ __raw_writel(reg, priv->reg); ++ raw_spin_unlock(priv->lock); ++} ++ ++static int bcm6345_ext_intc_set_type(struct irq_data *data, ++ unsigned int flow_type) ++{ ++ struct intc_data *priv = data->domain->host_data; ++ irq_hw_number_t hwirq = irqd_to_hwirq(data); ++ bool levelsense = 0, sense = 0, bothedge = 0; ++ u32 reg; ++ ++ flow_type &= IRQ_TYPE_SENSE_MASK; ++ ++ if (flow_type == IRQ_TYPE_NONE) ++ flow_type = IRQ_TYPE_LEVEL_LOW; ++ ++ switch (flow_type) { ++ case IRQ_TYPE_EDGE_BOTH: ++ bothedge = 1; ++ break; ++ ++ case IRQ_TYPE_EDGE_RISING: ++ break; ++ ++ case IRQ_TYPE_EDGE_FALLING: ++ sense = 1; ++ break; ++ ++ case IRQ_TYPE_LEVEL_HIGH: ++ levelsense = 1; ++ sense = 1; ++ break; ++ ++ case IRQ_TYPE_LEVEL_LOW: ++ levelsense = 1; ++ break; ++ ++ default: ++ pr_err("bogus flow type combination given!\n"); ++ return -EINVAL; ++ } ++ ++ raw_spin_lock(priv->lock); ++ reg = __raw_readl(priv->reg); ++ ++ if (levelsense) ++ reg |= hwirq << (EXTIRQ_CFG_LEVELSENSE * priv->shift); ++ else ++ reg &= ~(hwirq << (EXTIRQ_CFG_LEVELSENSE * priv->shift)); ++ if (sense) ++ reg |= hwirq << (EXTIRQ_CFG_SENSE * priv->shift); ++ else ++ reg &= ~(hwirq << (EXTIRQ_CFG_SENSE * priv->shift)); ++ if (bothedge) ++ reg |= hwirq << (EXTIRQ_CFG_BOTHEDGE * priv->shift); ++ else ++ reg &= ~(hwirq << (EXTIRQ_CFG_BOTHEDGE * priv->shift)); ++ ++ __raw_writel(reg, priv->reg); ++ raw_spin_unlock(priv->lock); ++ ++ irqd_set_trigger_type(data, flow_type); ++ if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) ++ __irq_set_handler_locked(data->irq, handle_level_irq); ++ else ++ __irq_set_handler_locked(data->irq, handle_edge_irq); ++ ++ return 0; ++} ++ ++static int bcm6345_ext_intc_map(struct irq_domain *d, unsigned int irq, ++ irq_hw_number_t hw) ++{ ++ struct intc_data *priv = d->host_data; ++ ++ irq_set_chip_and_handler(irq, &priv->chip, handle_level_irq); ++ ++ return 0; ++} ++ ++ ++static const struct irq_domain_ops bcm6345_ext_domain_ops = { ++ .xlate = irq_domain_xlate_twocell, ++ .map = bcm6345_ext_intc_map, ++}; ++ ++static int __init __bcm6345_ext_intc_init(struct device_node *node, ++ int num_irqs, int *irqs, ++ void __iomem *reg, int shift) ++{ ++ struct intc_data *data; ++ unsigned int i; ++ int start = VIRQ_BASE; ++ ++ data = kzalloc(sizeof(*data), GFP_KERNEL); ++ if (!data) ++ return -ENOMEM; ++ ++ for (i = 0; i < num_irqs; i++) { ++ data->parent_irq[i] = irqs[i]; ++ ++ irq_set_handler_data(irqs[i], data); ++ irq_set_chained_handler(irqs[i], bcm6345_ext_intc_irq_handle); ++ } ++ ++ data->reg = reg; ++ ++ data->chip.name = "bcm6345-ext-intc"; ++ data->chip.irq_ack = bcm6345_ext_intc_irq_ack; ++ data->chip.irq_mask = bcm6345_ext_intc_irq_mask; ++ data->chip.irq_unmask = bcm6345_ext_intc_irq_unmask; ++ data->chip.irq_set_type = bcm6345_ext_intc_set_type; ++ ++ /* ++ * If we have less than 4 irqs, this is the second controller on ++ * bcm63xx. So increase the VIRQ start to not overlap with the first ++ * one, but only do so if we actually use a non-zero start. ++ * ++ * This can be removed when bcm63xx has no legacy users anymore. ++ */ ++ if (start && num_irqs < 4) ++ start += 4; ++ ++ data->domain = irq_domain_add_simple(node, num_irqs, start, ++ &bcm6345_ext_domain_ops, data); ++ if (!data->domain) { ++ kfree(data); ++ return -ENOMEM; ++ } ++ ++ return 0; ++} ++ ++void __init bcm6345_ext_intc_init(int num_irqs, int *irqs, void __iomem *reg, ++ int shift) ++{ ++ __bcm6345_ext_intc_init(NULL, num_irqs, irqs, reg, shift); ++} ++ ++#ifdef CONFIG_OF ++static int __init bcm63xx_ext_intc_of_init(struct device_node *node, ++ struct device_node *parent, ++ int shift) ++{ ++ int num_irqs, ret = -EINVAL; ++ unsigned i; ++ void __iomem *base; ++ int irqs[MAX_IRQS] = { 0 }; ++ ++ num_irqs = of_irq_count(node); ++ ++ if (!num_irqs || num_irqs > MAX_IRQS) ++ return -EINVAL; ++ ++ for (i = 0; i < num_irqs; i++) { ++ irqs[i] = irq_of_parse_and_map(node, i); ++ if (!irqs[i]) { ++ ret = -ENOMEM; ++ goto out_unmap; ++ } ++ } ++ ++ base = of_iomap(node, 0); ++ if (!base) ++ goto out_unmap; ++ ++ ret = __bcm6345_ext_intc_init(node, num_irqs, irqs, base, shift); ++ if (!ret) ++ return 0; ++out_unmap: ++ iounmap(base); ++ ++ for (i = 0; i < num_irqs; i++) ++ irq_dispose_mapping(irqs[i]); ++ ++ return ret; ++} ++ ++static int __init bcm6345_ext_intc_of_init(struct device_node *node, ++ struct device_node *parent) ++{ ++ return bcm63xx_ext_intc_of_init(node, parent, 4); ++} ++static int __init bcm6348_ext_intc_of_init(struct device_node *node, ++ struct device_node *parent) ++{ ++ return bcm63xx_ext_intc_of_init(node, parent, 5); ++} ++ ++IRQCHIP_DECLARE(bcm6345_ext_intc, "brcm,bcm6345-ext-intc", ++ bcm6345_ext_intc_of_init); ++IRQCHIP_DECLARE(bcm6348_ext_intc, "brcm,bcm6348-ext-intc", ++ bcm6348_ext_intc_of_init); ++#endif +--- /dev/null ++++ b/include/linux/irqchip/irq-bcm6345-ext-intc.h +@@ -0,0 +1,14 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2014 Jonas Gorski <jogo@openwrt.org> ++ */ ++ ++#ifndef __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_EXT_INTC_H ++#define __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_EXT_INTC_H ++ ++void bcm6345_ext_intc_init(int n_irqs, int *irqs, void __iomem *reg, int shift); ++ ++#endif /* __INCLUDE_LINUX_IRQCHIP_IRQ_BCM6345_EXT_INTC_H */ diff --git a/target/linux/brcm63xx/patches-3.18/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch b/target/linux/brcm63xx/patches-3.18/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch new file mode 100644 index 0000000000..49c5bccb21 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch @@ -0,0 +1,694 @@ +From d93661c9e164ccc41820eeb4f1881e59a34a9e5c Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Nov 2014 14:55:02 +0100 +Subject: [PATCH 19/20] MIPS: BCM63XX: switch to IRQ_DOMAIN + +Now that we have working IRQ_DOMAIN drivers for both interrupt controllers, +switch to using them. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/Kconfig | 3 + + arch/mips/bcm63xx/irq.c | 608 ++++++++--------------------------------------- + 2 files changed, 108 insertions(+), 503 deletions(-) + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -144,6 +144,9 @@ config BCM63XX + select SYNC_R4K + select DMA_NONCOHERENT + select IRQ_CPU ++ select BCM6345_EXT_IRQ ++ select BCM6345_L2_IRQ ++ select IRQ_DOMAIN + select SYS_SUPPORTS_32BIT_KERNEL + select SYS_SUPPORTS_BIG_ENDIAN + select SYS_HAS_EARLY_PRINTK +--- a/arch/mips/bcm63xx/irq.c ++++ b/arch/mips/bcm63xx/irq.c +@@ -12,7 +12,9 @@ + #include <linux/interrupt.h> + #include <linux/module.h> + #include <linux/irq.h> +-#include <linux/spinlock.h> ++#include <linux/irqchip.h> ++#include <linux/irqchip/irq-bcm6345-ext-intc.h> ++#include <linux/irqchip/irq-bcm6345-l2-intc.h> + #include <asm/irq_cpu.h> + #include <asm/mipsregs.h> + #include <bcm63xx_cpu.h> +@@ -20,544 +22,144 @@ + #include <bcm63xx_io.h> + #include <bcm63xx_irq.h> + +- +-static DEFINE_SPINLOCK(ipic_lock); +-static DEFINE_SPINLOCK(epic_lock); +- +-static u32 irq_stat_addr[2]; +-static u32 irq_mask_addr[2]; +-static void (*dispatch_internal)(int cpu); +-static int is_ext_irq_cascaded; +-static unsigned int ext_irq_count; +-static unsigned int ext_irq_start, ext_irq_end; +-static unsigned int ext_irq_cfg_reg1, ext_irq_cfg_reg2; +-static void (*internal_irq_mask)(struct irq_data *d); +-static void (*internal_irq_unmask)(struct irq_data *d, const struct cpumask *m); +- +- +-static inline u32 get_ext_irq_perf_reg(int irq) +-{ +- if (irq < 4) +- return ext_irq_cfg_reg1; +- return ext_irq_cfg_reg2; +-} +- +-static inline void handle_internal(int intbit) +-{ +- if (is_ext_irq_cascaded && +- intbit >= ext_irq_start && intbit <= ext_irq_end) +- do_IRQ(intbit - ext_irq_start + IRQ_EXTERNAL_BASE); +- else +- do_IRQ(intbit + IRQ_INTERNAL_BASE); +-} +- +-static inline int enable_irq_for_cpu(int cpu, struct irq_data *d, +- const struct cpumask *m) +-{ +- bool enable = cpu_online(cpu); +- +-#ifdef CONFIG_SMP +- if (m) +- enable &= cpu_isset(cpu, *m); +- else if (irqd_affinity_was_set(d)) +- enable &= cpu_isset(cpu, *d->affinity); +-#endif +- return enable; +-} +- +-/* +- * dispatch internal devices IRQ (uart, enet, watchdog, ...). do not +- * prioritize any interrupt relatively to another. the static counter +- * will resume the loop where it ended the last time we left this +- * function. +- */ +- +-#define BUILD_IPIC_INTERNAL(width) \ +-void __dispatch_internal_##width(int cpu) \ +-{ \ +- u32 pending[width / 32]; \ +- unsigned int src, tgt; \ +- bool irqs_pending = false; \ +- static unsigned int i[2]; \ +- unsigned int *next = &i[cpu]; \ +- unsigned long flags; \ +- \ +- /* read registers in reverse order */ \ +- spin_lock_irqsave(&ipic_lock, flags); \ +- for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \ +- u32 val; \ +- \ +- val = bcm_readl(irq_stat_addr[cpu] + src * sizeof(u32)); \ +- val &= bcm_readl(irq_mask_addr[cpu] + src * sizeof(u32)); \ +- pending[--tgt] = val; \ +- \ +- if (val) \ +- irqs_pending = true; \ +- } \ +- spin_unlock_irqrestore(&ipic_lock, flags); \ +- \ +- if (!irqs_pending) \ +- return; \ +- \ +- while (1) { \ +- unsigned int to_call = *next; \ +- \ +- *next = (*next + 1) & (width - 1); \ +- if (pending[to_call / 32] & (1 << (to_call & 0x1f))) { \ +- handle_internal(to_call); \ +- break; \ +- } \ +- } \ +-} \ +- \ +-static void __internal_irq_mask_##width(struct irq_data *d) \ +-{ \ +- u32 val; \ +- unsigned irq = d->irq - IRQ_INTERNAL_BASE; \ +- unsigned reg = (irq / 32) ^ (width/32 - 1); \ +- unsigned bit = irq & 0x1f; \ +- unsigned long flags; \ +- int cpu; \ +- \ +- spin_lock_irqsave(&ipic_lock, flags); \ +- for_each_present_cpu(cpu) { \ +- if (!irq_mask_addr[cpu]) \ +- break; \ +- \ +- val = bcm_readl(irq_mask_addr[cpu] + reg * sizeof(u32));\ +- val &= ~(1 << bit); \ +- bcm_writel(val, irq_mask_addr[cpu] + reg * sizeof(u32));\ +- } \ +- spin_unlock_irqrestore(&ipic_lock, flags); \ +-} \ +- \ +-static void __internal_irq_unmask_##width(struct irq_data *d, \ +- const struct cpumask *m) \ +-{ \ +- u32 val; \ +- unsigned irq = d->irq - IRQ_INTERNAL_BASE; \ +- unsigned reg = (irq / 32) ^ (width/32 - 1); \ +- unsigned bit = irq & 0x1f; \ +- unsigned long flags; \ +- int cpu; \ +- \ +- spin_lock_irqsave(&ipic_lock, flags); \ +- for_each_present_cpu(cpu) { \ +- if (!irq_mask_addr[cpu]) \ +- break; \ +- \ +- val = bcm_readl(irq_mask_addr[cpu] + reg * sizeof(u32));\ +- if (enable_irq_for_cpu(cpu, d, m)) \ +- val |= (1 << bit); \ +- else \ +- val &= ~(1 << bit); \ +- bcm_writel(val, irq_mask_addr[cpu] + reg * sizeof(u32));\ +- } \ +- spin_unlock_irqrestore(&ipic_lock, flags); \ +-} +- +-BUILD_IPIC_INTERNAL(32); +-BUILD_IPIC_INTERNAL(64); +- +-asmlinkage void plat_irq_dispatch(void) +-{ +- u32 cause; +- +- do { +- cause = read_c0_cause() & read_c0_status() & ST0_IM; +- +- if (!cause) +- break; +- +- if (cause & CAUSEF_IP7) +- do_IRQ(7); +- if (cause & CAUSEF_IP0) +- do_IRQ(0); +- if (cause & CAUSEF_IP1) +- do_IRQ(1); +- if (cause & CAUSEF_IP2) +- dispatch_internal(0); +- if (is_ext_irq_cascaded) { +- if (cause & CAUSEF_IP3) +- dispatch_internal(1); +- } else { +- if (cause & CAUSEF_IP3) +- do_IRQ(IRQ_EXT_0); +- if (cause & CAUSEF_IP4) +- do_IRQ(IRQ_EXT_1); +- if (cause & CAUSEF_IP5) +- do_IRQ(IRQ_EXT_2); +- if (cause & CAUSEF_IP6) +- do_IRQ(IRQ_EXT_3); +- } +- } while (1); +-} +- +-/* +- * internal IRQs operations: only mask/unmask on PERF irq mask +- * register. +- */ +-static void bcm63xx_internal_irq_mask(struct irq_data *d) +-{ +- internal_irq_mask(d); +-} +- +-static void bcm63xx_internal_irq_unmask(struct irq_data *d) +-{ +- internal_irq_unmask(d, NULL); +-} +- +-/* +- * external IRQs operations: mask/unmask and clear on PERF external +- * irq control register. +- */ +-static void bcm63xx_external_irq_mask(struct irq_data *d) +-{ +- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; +- u32 reg, regaddr; +- unsigned long flags; +- +- regaddr = get_ext_irq_perf_reg(irq); +- spin_lock_irqsave(&epic_lock, flags); +- reg = bcm_perf_readl(regaddr); +- +- if (BCMCPU_IS_6348()) +- reg &= ~EXTIRQ_CFG_MASK_6348(irq % 4); +- else +- reg &= ~EXTIRQ_CFG_MASK(irq % 4); +- +- bcm_perf_writel(reg, regaddr); +- spin_unlock_irqrestore(&epic_lock, flags); +- +- if (is_ext_irq_cascaded) +- internal_irq_mask(irq_get_irq_data(irq + ext_irq_start)); +-} +- +-static void bcm63xx_external_irq_unmask(struct irq_data *d) +-{ +- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; +- u32 reg, regaddr; +- unsigned long flags; +- +- regaddr = get_ext_irq_perf_reg(irq); +- spin_lock_irqsave(&epic_lock, flags); +- reg = bcm_perf_readl(regaddr); +- +- if (BCMCPU_IS_6348()) +- reg |= EXTIRQ_CFG_MASK_6348(irq % 4); +- else +- reg |= EXTIRQ_CFG_MASK(irq % 4); +- +- bcm_perf_writel(reg, regaddr); +- spin_unlock_irqrestore(&epic_lock, flags); +- +- if (is_ext_irq_cascaded) +- internal_irq_unmask(irq_get_irq_data(irq + ext_irq_start), +- NULL); +-} +- +-static void bcm63xx_external_irq_clear(struct irq_data *d) +-{ +- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; +- u32 reg, regaddr; +- unsigned long flags; +- +- regaddr = get_ext_irq_perf_reg(irq); +- spin_lock_irqsave(&epic_lock, flags); +- reg = bcm_perf_readl(regaddr); +- +- if (BCMCPU_IS_6348()) +- reg |= EXTIRQ_CFG_CLEAR_6348(irq % 4); +- else +- reg |= EXTIRQ_CFG_CLEAR(irq % 4); +- +- bcm_perf_writel(reg, regaddr); +- spin_unlock_irqrestore(&epic_lock, flags); +-} +- +-static int bcm63xx_external_irq_set_type(struct irq_data *d, +- unsigned int flow_type) +-{ +- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE; +- u32 reg, regaddr; +- int levelsense, sense, bothedge; +- unsigned long flags; +- +- flow_type &= IRQ_TYPE_SENSE_MASK; +- +- if (flow_type == IRQ_TYPE_NONE) +- flow_type = IRQ_TYPE_LEVEL_LOW; +- +- levelsense = sense = bothedge = 0; +- switch (flow_type) { +- case IRQ_TYPE_EDGE_BOTH: +- bothedge = 1; +- break; +- +- case IRQ_TYPE_EDGE_RISING: +- sense = 1; +- break; +- +- case IRQ_TYPE_EDGE_FALLING: +- break; +- +- case IRQ_TYPE_LEVEL_HIGH: +- levelsense = 1; +- sense = 1; +- break; +- +- case IRQ_TYPE_LEVEL_LOW: +- levelsense = 1; +- break; +- +- default: +- printk(KERN_ERR "bogus flow type combination given !\n"); +- return -EINVAL; +- } +- +- regaddr = get_ext_irq_perf_reg(irq); +- spin_lock_irqsave(&epic_lock, flags); +- reg = bcm_perf_readl(regaddr); +- irq %= 4; +- +- switch (bcm63xx_get_cpu_id()) { +- case BCM6348_CPU_ID: +- if (levelsense) +- reg |= EXTIRQ_CFG_LEVELSENSE_6348(irq); +- else +- reg &= ~EXTIRQ_CFG_LEVELSENSE_6348(irq); +- if (sense) +- reg |= EXTIRQ_CFG_SENSE_6348(irq); +- else +- reg &= ~EXTIRQ_CFG_SENSE_6348(irq); +- if (bothedge) +- reg |= EXTIRQ_CFG_BOTHEDGE_6348(irq); +- else +- reg &= ~EXTIRQ_CFG_BOTHEDGE_6348(irq); +- break; +- +- case BCM3368_CPU_ID: +- case BCM6328_CPU_ID: +- case BCM6338_CPU_ID: +- case BCM6345_CPU_ID: +- case BCM6358_CPU_ID: +- case BCM6362_CPU_ID: +- case BCM6368_CPU_ID: +- if (levelsense) +- reg |= EXTIRQ_CFG_LEVELSENSE(irq); +- else +- reg &= ~EXTIRQ_CFG_LEVELSENSE(irq); +- if (sense) +- reg |= EXTIRQ_CFG_SENSE(irq); +- else +- reg &= ~EXTIRQ_CFG_SENSE(irq); +- if (bothedge) +- reg |= EXTIRQ_CFG_BOTHEDGE(irq); +- else +- reg &= ~EXTIRQ_CFG_BOTHEDGE(irq); +- break; +- default: +- BUG(); +- } +- +- bcm_perf_writel(reg, regaddr); +- spin_unlock_irqrestore(&epic_lock, flags); +- +- irqd_set_trigger_type(d, flow_type); +- if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH)) +- __irq_set_handler_locked(d->irq, handle_level_irq); +- else +- __irq_set_handler_locked(d->irq, handle_edge_irq); +- +- return IRQ_SET_MASK_OK_NOCOPY; +-} +- +-#ifdef CONFIG_SMP +-static int bcm63xx_internal_set_affinity(struct irq_data *data, +- const struct cpumask *dest, +- bool force) +-{ +- if (!irqd_irq_disabled(data)) +- internal_irq_unmask(data, dest); +- +- return 0; +-} +-#endif +- +-static struct irq_chip bcm63xx_internal_irq_chip = { +- .name = "bcm63xx_ipic", +- .irq_mask = bcm63xx_internal_irq_mask, +- .irq_unmask = bcm63xx_internal_irq_unmask, +-}; +- +-static struct irq_chip bcm63xx_external_irq_chip = { +- .name = "bcm63xx_epic", +- .irq_ack = bcm63xx_external_irq_clear, +- +- .irq_mask = bcm63xx_external_irq_mask, +- .irq_unmask = bcm63xx_external_irq_unmask, +- +- .irq_set_type = bcm63xx_external_irq_set_type, +-}; +- +-static struct irqaction cpu_ip2_cascade_action = { +- .handler = no_action, +- .name = "cascade_ip2", +- .flags = IRQF_NO_THREAD, +-}; +- +-#ifdef CONFIG_SMP +-static struct irqaction cpu_ip3_cascade_action = { +- .handler = no_action, +- .name = "cascade_ip3", +- .flags = IRQF_NO_THREAD, +-}; +-#endif +- +-static struct irqaction cpu_ext_cascade_action = { +- .handler = no_action, +- .name = "cascade_extirq", +- .flags = IRQF_NO_THREAD, +-}; +- + static void bcm63xx_init_irq(void) + { +- int irq_bits; +- +- irq_stat_addr[0] = bcm63xx_regset_address(RSET_PERF); +- irq_mask_addr[0] = bcm63xx_regset_address(RSET_PERF); +- irq_stat_addr[1] = bcm63xx_regset_address(RSET_PERF); +- irq_mask_addr[1] = bcm63xx_regset_address(RSET_PERF); ++ void __iomem *l2_intc_bases[2]; ++ void __iomem *ext_intc_bases[2]; ++ int l2_irq_count, l2_width, ext_irq_count, ext_shift; ++ int l2_irqs[2] = { 2, 3 }; ++ int ext_irqs[6]; ++ ++ l2_intc_bases[0] = (void __iomem *)bcm63xx_regset_address(RSET_PERF); ++ l2_intc_bases[1] = (void __iomem *)bcm63xx_regset_address(RSET_PERF); ++ ext_intc_bases[0] = (void __iomem *)bcm63xx_regset_address(RSET_PERF); ++ ext_intc_bases[1] = (void __iomem *)bcm63xx_regset_address(RSET_PERF); + + switch (bcm63xx_get_cpu_id()) { + case BCM3368_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_3368_REG; +- irq_mask_addr[0] += PERF_IRQMASK_3368_REG; +- irq_stat_addr[1] = 0; +- irq_mask_addr[1] = 0; +- irq_bits = 32; +- ext_irq_count = 4; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368; ++ l2_intc_bases[0] += PERF_IRQMASK_3368_REG; ++ l2_irq_count = 1; ++ l2_width = 1; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_3368; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_3368_EXT_IRQ0; ++ ext_irqs[1] = BCM_3368_EXT_IRQ1; ++ ext_irqs[2] = BCM_3368_EXT_IRQ2; ++ ext_irqs[3] = BCM_3368_EXT_IRQ3; ++ ext_shift = 4; + break; + case BCM6328_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6328_REG(0); +- irq_mask_addr[0] += PERF_IRQMASK_6328_REG(0); +- irq_stat_addr[1] += PERF_IRQSTAT_6328_REG(1); +- irq_mask_addr[1] += PERF_IRQMASK_6328_REG(1); +- irq_bits = 64; +- ext_irq_count = 4; +- is_ext_irq_cascaded = 1; +- ext_irq_start = BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE; +- ext_irq_end = BCM_6328_EXT_IRQ3 - IRQ_INTERNAL_BASE; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6328; ++ l2_intc_bases[0] += PERF_IRQMASK_6328_REG(0); ++ l2_intc_bases[1] += PERF_IRQMASK_6328_REG(1); ++ l2_irq_count = 2; ++ l2_width = 2; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6328; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_6328_EXT_IRQ0; ++ ext_irqs[1] = BCM_6328_EXT_IRQ1; ++ ext_irqs[2] = BCM_6328_EXT_IRQ2; ++ ext_irqs[3] = BCM_6328_EXT_IRQ3; ++ ext_shift = 4; + break; + case BCM6338_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6338_REG; +- irq_mask_addr[0] += PERF_IRQMASK_6338_REG; +- irq_stat_addr[1] = 0; +- irq_mask_addr[1] = 0; +- irq_bits = 32; +- ext_irq_count = 4; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338; ++ l2_intc_bases[0] += PERF_IRQMASK_6338_REG; ++ l2_irq_count = 1; ++ l2_width = 1; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6338; ++ ext_irq_count = 4; ++ ext_irqs[0] = 3; ++ ext_irqs[1] = 4; ++ ext_irqs[2] = 5; ++ ext_irqs[3] = 6; ++ ext_shift = 4; + break; + case BCM6345_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6345_REG; +- irq_mask_addr[0] += PERF_IRQMASK_6345_REG; +- irq_stat_addr[1] = 0; +- irq_mask_addr[1] = 0; +- irq_bits = 32; +- ext_irq_count = 4; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345; ++ l2_intc_bases[0] += PERF_IRQMASK_6345_REG; ++ l2_irq_count = 1; ++ l2_width = 1; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6345; ++ ext_irq_count = 4; ++ ext_irqs[0] = 3; ++ ext_irqs[1] = 4; ++ ext_irqs[2] = 5; ++ ext_irqs[3] = 6; ++ ext_shift = 4; + break; + case BCM6348_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6348_REG; +- irq_mask_addr[0] += PERF_IRQMASK_6348_REG; +- irq_stat_addr[1] = 0; +- irq_mask_addr[1] = 0; +- irq_bits = 32; +- ext_irq_count = 4; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6348; ++ l2_intc_bases[0] += PERF_IRQMASK_6348_REG; ++ l2_irq_count = 1; ++ l2_width = 1; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6348; ++ ext_irq_count = 4; ++ ext_irqs[0] = 3; ++ ext_irqs[1] = 4; ++ ext_irqs[2] = 5; ++ ext_irqs[3] = 6; ++ ext_shift = 5; + break; + case BCM6358_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6358_REG(0); +- irq_mask_addr[0] += PERF_IRQMASK_6358_REG(0); +- irq_stat_addr[1] += PERF_IRQSTAT_6358_REG(1); +- irq_mask_addr[1] += PERF_IRQMASK_6358_REG(1); +- irq_bits = 32; +- ext_irq_count = 4; +- is_ext_irq_cascaded = 1; +- ext_irq_start = BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE; +- ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358; ++ l2_intc_bases[0] += PERF_IRQMASK_6358_REG(0); ++ l2_intc_bases[1] += PERF_IRQMASK_6358_REG(1); ++ l2_irq_count = 2; ++ l2_width = 1; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6358; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_6358_EXT_IRQ0; ++ ext_irqs[1] = BCM_6358_EXT_IRQ1; ++ ext_irqs[2] = BCM_6358_EXT_IRQ2; ++ ext_irqs[3] = BCM_6358_EXT_IRQ3; ++ ext_shift = 4; + break; + case BCM6362_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6362_REG(0); +- irq_mask_addr[0] += PERF_IRQMASK_6362_REG(0); +- irq_stat_addr[1] += PERF_IRQSTAT_6362_REG(1); +- irq_mask_addr[1] += PERF_IRQMASK_6362_REG(1); +- irq_bits = 64; +- ext_irq_count = 4; +- is_ext_irq_cascaded = 1; +- ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE; +- ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362; ++ l2_intc_bases[0] += PERF_IRQMASK_6362_REG(0); ++ l2_intc_bases[1] += PERF_IRQMASK_6362_REG(1); ++ l2_irq_count = 2; ++ l2_width = 2; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6362; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_6362_EXT_IRQ0; ++ ext_irqs[1] = BCM_6362_EXT_IRQ1; ++ ext_irqs[2] = BCM_6362_EXT_IRQ2; ++ ext_irqs[3] = BCM_6362_EXT_IRQ3; ++ ext_shift = 4; + break; + case BCM6368_CPU_ID: +- irq_stat_addr[0] += PERF_IRQSTAT_6368_REG(0); +- irq_mask_addr[0] += PERF_IRQMASK_6368_REG(0); +- irq_stat_addr[1] += PERF_IRQSTAT_6368_REG(1); +- irq_mask_addr[1] += PERF_IRQMASK_6368_REG(1); +- irq_bits = 64; ++ l2_intc_bases[0] += PERF_IRQMASK_6368_REG(0); ++ l2_intc_bases[1] += PERF_IRQMASK_6368_REG(1); ++ l2_irq_count = 2; ++ l2_width = 2; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6368; ++ ext_intc_bases[1] += PERF_EXTIRQ_CFG_REG2_6368; + ext_irq_count = 6; +- is_ext_irq_cascaded = 1; +- ext_irq_start = BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE; +- ext_irq_end = BCM_6368_EXT_IRQ5 - IRQ_INTERNAL_BASE; +- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6368; +- ext_irq_cfg_reg2 = PERF_EXTIRQ_CFG_REG2_6368; ++ ext_irqs[0] = BCM_6368_EXT_IRQ0; ++ ext_irqs[1] = BCM_6368_EXT_IRQ1; ++ ext_irqs[2] = BCM_6368_EXT_IRQ2; ++ ext_irqs[3] = BCM_6368_EXT_IRQ3; ++ ext_irqs[4] = BCM_6368_EXT_IRQ4; ++ ext_irqs[5] = BCM_6368_EXT_IRQ5; ++ ext_shift = 4; + break; + default: + BUG(); + } + +- if (irq_bits == 32) { +- dispatch_internal = __dispatch_internal_32; +- internal_irq_mask = __internal_irq_mask_32; +- internal_irq_unmask = __internal_irq_unmask_32; +- } else { +- dispatch_internal = __dispatch_internal_64; +- internal_irq_mask = __internal_irq_mask_64; +- internal_irq_unmask = __internal_irq_unmask_64; +- } ++ mips_cpu_irq_init(); ++ bcm6345_l2_intc_init(l2_irq_count, l2_irqs, l2_intc_bases, l2_width); ++ bcm6345_ext_intc_init(4, ext_irqs, ext_intc_bases[0], ext_shift); ++ if (ext_irq_count > 4) ++ bcm6345_ext_intc_init(2, &ext_irqs[4], ext_intc_bases[1], ++ ext_shift); + } + + void __init arch_init_irq(void) + { +- int i; +- + bcm63xx_init_irq(); +- mips_cpu_irq_init(); +- for (i = IRQ_INTERNAL_BASE; i < NR_IRQS; ++i) +- irq_set_chip_and_handler(i, &bcm63xx_internal_irq_chip, +- handle_level_irq); +- +- for (i = IRQ_EXTERNAL_BASE; i < IRQ_EXTERNAL_BASE + ext_irq_count; ++i) +- irq_set_chip_and_handler(i, &bcm63xx_external_irq_chip, +- handle_edge_irq); +- +- if (!is_ext_irq_cascaded) { +- for (i = 3; i < 3 + ext_irq_count; ++i) +- setup_irq(MIPS_CPU_IRQ_BASE + i, &cpu_ext_cascade_action); +- } +- +- setup_irq(MIPS_CPU_IRQ_BASE + 2, &cpu_ip2_cascade_action); +-#ifdef CONFIG_SMP +- if (is_ext_irq_cascaded) { +- setup_irq(MIPS_CPU_IRQ_BASE + 3, &cpu_ip3_cascade_action); +- bcm63xx_internal_irq_chip.irq_set_affinity = +- bcm63xx_internal_set_affinity; +- +- cpumask_clear(irq_default_affinity); +- cpumask_set_cpu(smp_processor_id(), irq_default_affinity); +- } +-#endif + } diff --git a/target/linux/brcm63xx/patches-3.18/323-MIPS-BCM63XX-wire-up-BCM6358-s-external-interrupts-4.patch b/target/linux/brcm63xx/patches-3.18/323-MIPS-BCM63XX-wire-up-BCM6358-s-external-interrupts-4.patch new file mode 100644 index 0000000000..3e718772ca --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/323-MIPS-BCM63XX-wire-up-BCM6358-s-external-interrupts-4.patch @@ -0,0 +1,57 @@ +From e3c68bbba30b212326fb69bf64b2220750dead3e Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 30 Nov 2014 20:20:30 +0100 +Subject: [PATCH 20/20] MIPS: BCM63XX: wire up BCM6358's external interrupts 4 + and 5 + +Due to the external interrupts being non consecutive, the previous +implementation did not support them. Now that we treat both registers +as separate irq controllers, there is no such limitation anymore and +we can expose them for drivers to use. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/irq.c | 5 ++++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 2 ++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 1 + + 3 files changed, 7 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/irq.c ++++ b/arch/mips/bcm63xx/irq.c +@@ -109,11 +109,14 @@ static void bcm63xx_init_irq(void) + l2_width = 1; + + ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6358; +- ext_irq_count = 4; ++ ext_intc_bases[1] += PERF_EXTIRQ_CFG_REG2_6358; ++ ext_irq_count = 6; + ext_irqs[0] = BCM_6358_EXT_IRQ0; + ext_irqs[1] = BCM_6358_EXT_IRQ1; + ext_irqs[2] = BCM_6358_EXT_IRQ2; + ext_irqs[3] = BCM_6358_EXT_IRQ3; ++ ext_irqs[4] = BCM_6358_EXT_IRQ4; ++ ext_irqs[5] = BCM_6358_EXT_IRQ5; + ext_shift = 4; + break; + case BCM6362_CPU_ID: +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -895,6 +895,8 @@ enum bcm63xx_irq { + #define BCM_6358_EXT_IRQ1 (IRQ_INTERNAL_BASE + 26) + #define BCM_6358_EXT_IRQ2 (IRQ_INTERNAL_BASE + 27) + #define BCM_6358_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28) ++#define BCM_6358_EXT_IRQ4 (IRQ_INTERNAL_BASE + 20) ++#define BCM_6358_EXT_IRQ5 (IRQ_INTERNAL_BASE + 21) + + /* + * 6362 irqs +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -243,6 +243,7 @@ + #define PERF_EXTIRQ_CFG_REG_6362 0x18 + #define PERF_EXTIRQ_CFG_REG_6368 0x18 + ++#define PERF_EXTIRQ_CFG_REG2_6358 0x1c + #define PERF_EXTIRQ_CFG_REG2_6368 0x1c + + /* for 6348 only */ diff --git a/target/linux/brcm63xx/patches-3.18/330-MIPS-BCM63XX-add-a-new-cpu-variant-helper.patch b/target/linux/brcm63xx/patches-3.18/330-MIPS-BCM63XX-add-a-new-cpu-variant-helper.patch new file mode 100644 index 0000000000..661abf6d85 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/330-MIPS-BCM63XX-add-a-new-cpu-variant-helper.patch @@ -0,0 +1,77 @@ +From c50acd37b425a8a907a6f7f93aa2e658256e79ce Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:08:36 +0100 +Subject: [PATCH 40/53] MIPS: BCM63XX: add a new cpu variant helper + +--- + arch/mips/bcm63xx/cpu.c | 10 ++++++++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 18 ++++++++++++++++++ + 2 files changed, 28 insertions(+) + +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -27,6 +27,8 @@ EXPORT_SYMBOL(bcm63xx_irqs); + u16 bcm63xx_cpu_id __read_mostly; + EXPORT_SYMBOL(bcm63xx_cpu_id); + ++static u32 bcm63xx_cpu_variant __read_mostly; ++ + static u8 bcm63xx_cpu_rev; + static unsigned int bcm63xx_cpu_freq; + static unsigned int bcm63xx_memory_size; +@@ -99,6 +101,13 @@ static const int bcm6368_irqs[] = { + + }; + ++u32 bcm63xx_get_cpu_variant(void) ++{ ++ return bcm63xx_cpu_variant; ++} ++ ++EXPORT_SYMBOL(bcm63xx_get_cpu_variant); ++ + u8 bcm63xx_get_cpu_rev(void) + { + return bcm63xx_cpu_rev; +@@ -333,6 +342,7 @@ void __init bcm63xx_cpu_init(void) + /* read out CPU type */ + tmp = bcm_readl(chipid_reg); + bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT; ++ bcm63xx_cpu_variant = bcm63xx_cpu_id; + bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT; + + switch (bcm63xx_cpu_id) { +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -19,6 +19,7 @@ + #define BCM6368_CPU_ID 0x6368 + + void __init bcm63xx_cpu_init(void); ++u32 bcm63xx_get_cpu_variant(void); + u8 bcm63xx_get_cpu_rev(void); + unsigned int bcm63xx_get_cpu_freq(void); + +@@ -82,6 +83,23 @@ static inline u16 __pure bcm63xx_get_cpu + #define BCMCPU_IS_6362() (bcm63xx_get_cpu_id() == BCM6362_CPU_ID) + #define BCMCPU_IS_6368() (bcm63xx_get_cpu_id() == BCM6368_CPU_ID) + ++#define BCMCPU_VARIANT_IS_3368() \ ++ (bcm63xx_get_cpu_variant() == BCM3368_CPU_ID) ++#define BCMCPU_VARIANT_IS_6328() \ ++ (bcm63xx_get_cpu_variant() == BCM6328_CPU_ID) ++#define BCMCPU_VARIANT_IS_6338() \ ++ (bcm63xx_get_cpu_variant() == BCM6338_CPU_ID) ++#define BCMCPU_VARIANT_IS_6345() \ ++ (bcm63xx_get_cpu_variant() == BCM6345_CPU_ID) ++#define BCMCPU_VARIANT_IS_6348() \ ++ (bcm63xx_get_cpu_variant() == BCM6348_CPU_ID) ++#define BCMCPU_VARIANT_IS_6358() \ ++ (bcm63xx_get_cpu_cariant() == BCM6358_CPU_ID) ++#define BCMCPU_VARIANT_IS_6362() \ ++ (bcm63xx_get_cpu_variant() == BCM6362_CPU_ID) ++#define BCMCPU_VARIANT_IS_6368() \ ++ (bcm63xx_get_cpu_variant() == BCM6368_CPU_ID) ++ + /* + * While registers sets are (mostly) the same across 63xx CPU, base + * address of these sets do change. diff --git a/target/linux/brcm63xx/patches-3.18/331-MIPS-BCM63XX-define-variant-id-field.patch b/target/linux/brcm63xx/patches-3.18/331-MIPS-BCM63XX-define-variant-id-field.patch new file mode 100644 index 0000000000..2e21c65009 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/331-MIPS-BCM63XX-define-variant-id-field.patch @@ -0,0 +1,23 @@ +From 3bd8e2535265f06f79ed9c0ad788405441e091dc Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:22:41 +0100 +Subject: [PATCH 21/45] MIPS: BCM63XX: define variant id field + +Some SoC have a variant id field in the chip id register. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -9,6 +9,8 @@ + #define PERF_REV_REG 0x0 + #define REV_CHIPID_SHIFT 16 + #define REV_CHIPID_MASK (0xffff << REV_CHIPID_SHIFT) ++#define REV_VARID_SHIFT 12 ++#define REV_VARID_MASK (0xf << REV_VARID_SHIFT) + #define REV_REVID_SHIFT 0 + #define REV_REVID_MASK (0xff << REV_REVID_SHIFT) + diff --git a/target/linux/brcm63xx/patches-3.18/332-MIPS-BCM63XX-detect-BCM6328-variants.patch b/target/linux/brcm63xx/patches-3.18/332-MIPS-BCM63XX-detect-BCM6328-variants.patch new file mode 100644 index 0000000000..faa002e1e3 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/332-MIPS-BCM63XX-detect-BCM6328-variants.patch @@ -0,0 +1,68 @@ +From d59120f23279ef62a48d9f94847254b061d0a8b6 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:30:59 +0100 +Subject: [PATCH 22/45] MIPS: BCM63XX: detect BCM6328 variants + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/cpu.c | 10 ++++++++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 8 ++++++-- + 2 files changed, 16 insertions(+), 2 deletions(-) + +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -305,6 +305,7 @@ void __init bcm63xx_cpu_init(void) + unsigned int tmp; + unsigned int cpu = smp_processor_id(); + u32 chipid_reg; ++ u8 __maybe_unused varid = 0; + + /* soc registers location depends on cpu type */ + chipid_reg = 0; +@@ -344,6 +345,7 @@ void __init bcm63xx_cpu_init(void) + bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT; + bcm63xx_cpu_variant = bcm63xx_cpu_id; + bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT; ++ varid = (tmp & REV_VARID_MASK) >> REV_VARID_SHIFT; + + switch (bcm63xx_cpu_id) { + case BCM3368_CPU_ID: +@@ -353,6 +355,14 @@ void __init bcm63xx_cpu_init(void) + case BCM6328_CPU_ID: + bcm63xx_regs_base = bcm6328_regs_base; + bcm63xx_irqs = bcm6328_irqs; ++ ++ if (varid == 1) ++ bcm63xx_cpu_variant = BCM63281_CPU_ID; ++ else if (varid == 3) ++ bcm63xx_cpu_variant = BCM63283_CPU_ID; ++ else ++ pr_warn("unknown BCM6328 variant: %x\n", varid); ++ + break; + case BCM6338_CPU_ID: + bcm63xx_regs_base = bcm6338_regs_base; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -11,6 +11,8 @@ + */ + #define BCM3368_CPU_ID 0x3368 + #define BCM6328_CPU_ID 0x6328 ++#define BCM63281_CPU_ID 0x63281 ++#define BCM63283_CPU_ID 0x63283 + #define BCM6338_CPU_ID 0x6338 + #define BCM6345_CPU_ID 0x6345 + #define BCM6348_CPU_ID 0x6348 +@@ -85,8 +87,10 @@ static inline u16 __pure bcm63xx_get_cpu + + #define BCMCPU_VARIANT_IS_3368() \ + (bcm63xx_get_cpu_variant() == BCM3368_CPU_ID) +-#define BCMCPU_VARIANT_IS_6328() \ +- (bcm63xx_get_cpu_variant() == BCM6328_CPU_ID) ++#define BCMCPU_VARIANT_IS_63281() \ ++ (bcm63xx_get_cpu_variant() == BCM63281_CPU_ID) ++#define BCMCPU_VARIANT_IS_63283() \ ++ (bcm63xx_get_cpu_variant() == BCM63283_CPU_ID) + #define BCMCPU_VARIANT_IS_6338() \ + (bcm63xx_get_cpu_variant() == BCM6338_CPU_ID) + #define BCMCPU_VARIANT_IS_6345() \ diff --git a/target/linux/brcm63xx/patches-3.18/333-MIPS-BCM63XX-detect-BCM6362-variants.patch b/target/linux/brcm63xx/patches-3.18/333-MIPS-BCM63XX-detect-BCM6362-variants.patch new file mode 100644 index 0000000000..62ce12eda5 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/333-MIPS-BCM63XX-detect-BCM6362-variants.patch @@ -0,0 +1,46 @@ +From 04458c3db8eb79da21ecde40ab36a1dde52bef06 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:33:28 +0100 +Subject: [PATCH 23/45] MIPS: BCM63XX: detect BCM6362 variants + +--- + arch/mips/bcm63xx/cpu.c | 8 ++++++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 3 +++ + 2 files changed, 11 insertions(+) + +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -383,6 +383,14 @@ void __init bcm63xx_cpu_init(void) + case BCM6362_CPU_ID: + bcm63xx_regs_base = bcm6362_regs_base; + bcm63xx_irqs = bcm6362_irqs; ++ ++ if (varid == 1) ++ bcm63xx_cpu_variant = BCM6362_CPU_ID; ++ else if (varid == 2) ++ bcm63xx_cpu_variant = BCM6361_CPU_ID; ++ else ++ pr_warn("unknown BCM6362 variant: %x\n", varid); ++ + break; + case BCM6368_CPU_ID: + bcm63xx_regs_base = bcm6368_regs_base; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -17,6 +17,7 @@ + #define BCM6345_CPU_ID 0x6345 + #define BCM6348_CPU_ID 0x6348 + #define BCM6358_CPU_ID 0x6358 ++#define BCM6361_CPU_ID 0x6361 + #define BCM6362_CPU_ID 0x6362 + #define BCM6368_CPU_ID 0x6368 + +@@ -99,6 +100,8 @@ static inline u16 __pure bcm63xx_get_cpu + (bcm63xx_get_cpu_variant() == BCM6348_CPU_ID) + #define BCMCPU_VARIANT_IS_6358() \ + (bcm63xx_get_cpu_cariant() == BCM6358_CPU_ID) ++#define BCMCPU_VARIANT_IS_6361() \ ++ (bcm63xx_get_cpu_variant() == BCM6361_CPU_ID) + #define BCMCPU_VARIANT_IS_6362() \ + (bcm63xx_get_cpu_variant() == BCM6362_CPU_ID) + #define BCMCPU_VARIANT_IS_6368() \ diff --git a/target/linux/brcm63xx/patches-3.18/334-MIPS-BCM63XX-detect-BCM6368-variants.patch b/target/linux/brcm63xx/patches-3.18/334-MIPS-BCM63XX-detect-BCM6368-variants.patch new file mode 100644 index 0000000000..a993e238e4 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/334-MIPS-BCM63XX-detect-BCM6368-variants.patch @@ -0,0 +1,48 @@ +From 825cc67e56b5e624a05f6850a86d91508b786848 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:36:56 +0100 +Subject: [PATCH 24/44] MIPS: BCM63XX: detect BCM6368 variants + +The DSL-less BCM6368 variant BCM6367 uses a different chip id. Apart +from missing DSL, there is no difference to BCM6368, so treat it such. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/cpu.c | 4 ++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 3 +++ + 2 files changed, 7 insertions(+) + +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -393,8 +393,12 @@ void __init bcm63xx_cpu_init(void) + + break; + case BCM6368_CPU_ID: ++ case BCM6369_CPU_ID: + bcm63xx_regs_base = bcm6368_regs_base; + bcm63xx_irqs = bcm6368_irqs; ++ ++ /* BCM6369 is a BCM6368 without xDSL, so treat it the same */ ++ bcm63xx_cpu_id = BCM6368_CPU_ID; + break; + default: + panic("unsupported broadcom CPU %x", bcm63xx_cpu_id); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -20,6 +20,7 @@ + #define BCM6361_CPU_ID 0x6361 + #define BCM6362_CPU_ID 0x6362 + #define BCM6368_CPU_ID 0x6368 ++#define BCM6369_CPU_ID 0x6369 + + void __init bcm63xx_cpu_init(void); + u32 bcm63xx_get_cpu_variant(void); +@@ -106,6 +107,8 @@ static inline u16 __pure bcm63xx_get_cpu + (bcm63xx_get_cpu_variant() == BCM6362_CPU_ID) + #define BCMCPU_VARIANT_IS_6368() \ + (bcm63xx_get_cpu_variant() == BCM6368_CPU_ID) ++#define BCMCPU_VARIANT_IS_6369() \ ++ (bcm63xx_get_cpu_variant() == BCM6369_CPU_ID) + + /* + * While registers sets are (mostly) the same across 63xx CPU, base diff --git a/target/linux/brcm63xx/patches-3.18/335-MIPS-BCM63XX-fix-PCIe-memory-window-size.patch b/target/linux/brcm63xx/patches-3.18/335-MIPS-BCM63XX-fix-PCIe-memory-window-size.patch new file mode 100644 index 0000000000..3230add278 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/335-MIPS-BCM63XX-fix-PCIe-memory-window-size.patch @@ -0,0 +1,20 @@ +From f67f8134b4537c8bbafe7e1975edfe808b813997 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 8 Dec 2013 03:05:54 +0100 +Subject: [PATCH 45/53] MIPS: BCM63XX: fix PCIe memory window size + +--- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h +@@ -41,7 +41,7 @@ + BCM_CB_MEM_SIZE - 1) + + #define BCM_PCIE_MEM_BASE_PA 0x10f00000 +-#define BCM_PCIE_MEM_SIZE (16 * 1024 * 1024) ++#define BCM_PCIE_MEM_SIZE (1 * 1024 * 1024) + #define BCM_PCIE_MEM_END_PA (BCM_PCIE_MEM_BASE_PA + \ + BCM_PCIE_MEM_SIZE - 1) + diff --git a/target/linux/brcm63xx/patches-3.18/336-MIPS-BCM63XX-dynamically-set-the-pcie-memory-windows.patch b/target/linux/brcm63xx/patches-3.18/336-MIPS-BCM63XX-dynamically-set-the-pcie-memory-windows.patch new file mode 100644 index 0000000000..d6eb54d2e8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/336-MIPS-BCM63XX-dynamically-set-the-pcie-memory-windows.patch @@ -0,0 +1,70 @@ +From aa05464973bc176478af462ca7c53a9239c651d4 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 8 Dec 2013 03:13:06 +0100 +Subject: [PATCH 46/53] MIPS: BCM63XX: dynamically set the pcie memory windows + +Different SoCs use different memory windows (and sizes), so don't +hardcode it. +--- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h | 8 ++++---- + arch/mips/pci/pci-bcm63xx.c | 15 ++++++++++----- + 2 files changed, 14 insertions(+), 9 deletions(-) + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h +@@ -40,10 +40,10 @@ + #define BCM_CB_MEM_END_PA (BCM_CB_MEM_BASE_PA + \ + BCM_CB_MEM_SIZE - 1) + +-#define BCM_PCIE_MEM_BASE_PA 0x10f00000 +-#define BCM_PCIE_MEM_SIZE (1 * 1024 * 1024) +-#define BCM_PCIE_MEM_END_PA (BCM_PCIE_MEM_BASE_PA + \ +- BCM_PCIE_MEM_SIZE - 1) ++#define BCM_PCIE_MEM_BASE_PA_6328 0x10f00000 ++#define BCM_PCIE_MEM_SIZE_6328 (1 * 1024 * 1024) ++#define BCM_PCIE_MEM_END_PA_6328 (BCM_PCIE_MEM_BASE_PA_6328 + \ ++ BCM_PCIE_MEM_SIZE_6328 - 1) + + /* + * Internal registers are accessed through KSEG3 +--- a/arch/mips/pci/pci-bcm63xx.c ++++ b/arch/mips/pci/pci-bcm63xx.c +@@ -77,8 +77,8 @@ struct pci_controller bcm63xx_cb_control + + static struct resource bcm_pcie_mem_resource = { + .name = "bcm63xx PCIe memory space", +- .start = BCM_PCIE_MEM_BASE_PA, +- .end = BCM_PCIE_MEM_END_PA, ++ .start = 0, ++ .end = 0, + .flags = IORESOURCE_MEM, + }; + +@@ -195,12 +195,12 @@ static int __init bcm63xx_register_pcie( + bcm_pcie_writel(val, PCIE_CONFIG2_REG); + + /* set bar0 to little endian */ +- val = (BCM_PCIE_MEM_BASE_PA >> 20) << BASEMASK_BASE_SHIFT; +- val |= (BCM_PCIE_MEM_BASE_PA >> 20) << BASEMASK_MASK_SHIFT; ++ val = (bcm_pcie_mem_resource.start >> 20) << BASEMASK_BASE_SHIFT; ++ val |= (bcm_pcie_mem_resource.end >> 20) << BASEMASK_MASK_SHIFT; + val |= BASEMASK_REMAP_EN; + bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_BASEMASK_REG); + +- val = (BCM_PCIE_MEM_BASE_PA >> 20) << REBASE_ADDR_BASE_SHIFT; ++ val = (bcm_pcie_mem_resource.start >> 20) << REBASE_ADDR_BASE_SHIFT; + bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_REBASE_ADDR_REG); + + register_pci_controller(&bcm63xx_pcie_controller); +@@ -334,6 +334,11 @@ static int __init bcm63xx_pci_init(void) + if (!bcm63xx_pci_enabled) + return -ENODEV; + ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { ++ bcm_pcie_mem_resource.start = BCM_PCIE_MEM_BASE_PA_6328; ++ bcm_pcie_mem_resource.end = BCM_PCIE_MEM_END_PA_6328; ++ } ++ + switch (bcm63xx_get_cpu_id()) { + case BCM6328_CPU_ID: + case BCM6362_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.18/337-MIPS-BCM63XX-widen-cpuid-field.patch b/target/linux/brcm63xx/patches-3.18/337-MIPS-BCM63XX-widen-cpuid-field.patch new file mode 100644 index 0000000000..0ead82e862 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/337-MIPS-BCM63XX-widen-cpuid-field.patch @@ -0,0 +1,56 @@ +From f1477f6e3551fd6beecfee5368fed1325dcd421f Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 14:54:51 +0100 +Subject: [PATCH 47/53] MIPS: BCM63XX: widen cpuid field + +--- + arch/mips/bcm63xx/cpu.c | 2 +- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 8 ++++---- + 2 files changed, 5 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -24,7 +24,7 @@ EXPORT_SYMBOL(bcm63xx_regs_base); + const int *bcm63xx_irqs; + EXPORT_SYMBOL(bcm63xx_irqs); + +-u16 bcm63xx_cpu_id __read_mostly; ++u32 bcm63xx_cpu_id __read_mostly; + EXPORT_SYMBOL(bcm63xx_cpu_id); + + static u32 bcm63xx_cpu_variant __read_mostly; +@@ -127,7 +127,7 @@ unsigned int bcm63xx_get_memory_size(voi + + static unsigned int detect_cpu_clock(void) + { +- u16 cpu_id = bcm63xx_get_cpu_id(); ++ u32 cpu_id = bcm63xx_get_cpu_id(); + + switch (cpu_id) { + case BCM3368_CPU_ID: +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -27,7 +27,7 @@ u32 bcm63xx_get_cpu_variant(void); + u8 bcm63xx_get_cpu_rev(void); + unsigned int bcm63xx_get_cpu_freq(void); + +-static inline u16 __pure __bcm63xx_get_cpu_id(const u16 cpu_id) ++static inline u32 __pure __bcm63xx_get_cpu_id(const u32 cpu_id) + { + switch (cpu_id) { + #ifdef CONFIG_BCM63XX_CPU_3368 +@@ -69,11 +69,11 @@ static inline u16 __pure __bcm63xx_get_c + return cpu_id; + } + +-extern u16 bcm63xx_cpu_id; ++extern u32 bcm63xx_cpu_id; + +-static inline u16 __pure bcm63xx_get_cpu_id(void) ++static inline u32 __pure bcm63xx_get_cpu_id(void) + { +- const u16 cpu_id = bcm63xx_cpu_id; ++ const u32 cpu_id = bcm63xx_cpu_id; + + return __bcm63xx_get_cpu_id(cpu_id); + } diff --git a/target/linux/brcm63xx/patches-3.18/338-MIPS-BCM63XX-increase-number-of-IRQs.patch b/target/linux/brcm63xx/patches-3.18/338-MIPS-BCM63XX-increase-number-of-IRQs.patch new file mode 100644 index 0000000000..9132e42312 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/338-MIPS-BCM63XX-increase-number-of-IRQs.patch @@ -0,0 +1,39 @@ +From 6f5658c845cf1f79213b1d20423a04967259fdaa Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 15 Dec 2013 20:46:26 +0100 +Subject: [PATCH 48/53] MIPS: BCM63XX: increase number of IRQs + +Newer SoCs have 128 bit wide irq registers, thus 128 available internal +interupts. +--- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h | 4 +++- + arch/mips/include/asm/mach-bcm63xx/irq.h | 2 +- + 2 files changed, 4 insertions(+), 2 deletions(-) + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_irq.h +@@ -1,10 +1,12 @@ + #ifndef BCM63XX_IRQ_H_ + #define BCM63XX_IRQ_H_ + ++#include <irq.h> + #include <bcm63xx_cpu.h> + + #define IRQ_INTERNAL_BASE 8 +-#define IRQ_EXTERNAL_BASE 100 ++#define NR_INTERNAL_IRQS 128 ++#define IRQ_EXTERNAL_BASE (IRQ_INTERNAL_BASE + NR_INTERNAL_IRQS) + #define IRQ_EXT_0 (IRQ_EXTERNAL_BASE + 0) + #define IRQ_EXT_1 (IRQ_EXTERNAL_BASE + 1) + #define IRQ_EXT_2 (IRQ_EXTERNAL_BASE + 2) +--- a/arch/mips/include/asm/mach-bcm63xx/irq.h ++++ b/arch/mips/include/asm/mach-bcm63xx/irq.h +@@ -1,7 +1,7 @@ + #ifndef __ASM_MACH_BCM63XX_IRQ_H + #define __ASM_MACH_BCM63XX_IRQ_H + +-#define NR_IRQS 128 ++#define NR_IRQS 256 + #define MIPS_CPU_IRQ_BASE 0 + + #endif diff --git a/target/linux/brcm63xx/patches-3.18/339-MIPS-BCM63XX-add-support-for-BCM63268.patch b/target/linux/brcm63xx/patches-3.18/339-MIPS-BCM63XX-add-support-for-BCM63268.patch new file mode 100644 index 0000000000..5abdd9d09f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/339-MIPS-BCM63XX-add-support-for-BCM63268.patch @@ -0,0 +1,739 @@ +From 98f63141190ac02c58b78d58f771bd263c61d756 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 7 Dec 2013 17:14:17 +0100 +Subject: [PATCH 48/56] MIPS: BCM63XX: add support for BCM63268 + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/Kconfig | 5 + + arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- + arch/mips/bcm63xx/clk.c | 25 ++++- + arch/mips/bcm63xx/cpu.c | 59 +++++++++- + arch/mips/bcm63xx/dev-flash.c | 6 + + arch/mips/bcm63xx/dev-spi.c | 4 +- + arch/mips/bcm63xx/irq.c | 20 +++- + arch/mips/bcm63xx/reset.c | 21 ++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 130 ++++++++++++++++++++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h | 2 + + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 79 +++++++++++++ + arch/mips/include/asm/mach-bcm63xx/ioremap.h | 1 + + 12 files changed, 342 insertions(+), 12 deletions(-) + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -60,6 +60,11 @@ config BCM63XX_CPU_6368 + select HW_HAS_PCI + select BCM63XX_OHCI + select BCM63XX_EHCI ++ ++config BCM63XX_CPU_63268 ++ bool "support 63268 CPU" ++ select SYS_HAS_CPU_BMIPS4350 ++ select HW_HAS_PCI + endmenu + + source "arch/mips/bcm63xx/boards/Kconfig" +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -737,7 +737,7 @@ void __init board_prom_init(void) + /* read base address of boot chip select (0) + * 6328/6362 do not have MPI but boot from a fixed address + */ +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) { + val = 0x18000000; + } else { + val = bcm_mpi_readl(MPI_CSBASE_REG(0)); +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -133,6 +133,8 @@ static void enetsw_set(struct clk *clk, + CKCTL_6368_SWPKT_USB_EN | + CKCTL_6368_SWPKT_SAR_EN, + enable); ++ else if (BCMCPU_IS_63268()) ++ bcm_hwclock_set(CKCTL_63268_ROBOSW_EN, enable); + else + return; + +@@ -177,6 +179,8 @@ static void usbh_set(struct clk *clk, in + bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); + else if (BCMCPU_IS_6368()) + bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); ++ else if (BCMCPU_IS_63268()) ++ bcm_hwclock_set(CKCTL_63268_USBH_EN, enable); + else + return; + +@@ -199,6 +203,8 @@ static void usbd_set(struct clk *clk, in + bcm_hwclock_set(CKCTL_6362_USBD_EN, enable); + else if (BCMCPU_IS_6368()) + bcm_hwclock_set(CKCTL_6368_USBD_EN, enable); ++ else if (BCMCPU_IS_63268()) ++ bcm_hwclock_set(CKCTL_63268_USBD_EN, enable); + else + return; + +@@ -225,9 +231,13 @@ static void spi_set(struct clk *clk, int + mask = CKCTL_6358_SPI_EN; + else if (BCMCPU_IS_6362()) + mask = CKCTL_6362_SPI_EN; +- else +- /* BCMCPU_IS_6368 */ ++ else if (BCMCPU_IS_6368()) + mask = CKCTL_6368_SPI_EN; ++ else if (BCMCPU_IS_63268()) ++ mask = CKCTL_63268_SPI_EN; ++ else ++ return; ++ + bcm_hwclock_set(mask, enable); + } + +@@ -246,6 +256,8 @@ static void hsspi_set(struct clk *clk, i + mask = CKCTL_6328_HSSPI_EN; + else if (BCMCPU_IS_6362()) + mask = CKCTL_6362_HSSPI_EN; ++ else if (BCMCPU_IS_63268()) ++ mask = CKCTL_63268_HSSPI_EN; + else + return; + +@@ -307,6 +319,8 @@ static void pcie_set(struct clk *clk, in + bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable); + else if (BCMCPU_IS_6362()) + bcm_hwclock_set(CKCTL_6362_PCIE_EN, enable); ++ else if (BCMCPU_IS_63268()) ++ bcm_hwclock_set(CKCTL_63268_PCIE_EN, enable); + } + + static struct clk clk_pcie = { +@@ -386,9 +400,11 @@ struct clk *clk_get(struct device *dev, + return &clk_periph; + if ((BCMCPU_IS_3368() || BCMCPU_IS_6358()) && !strcmp(id, "pcm")) + return &clk_pcm; +- if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec")) ++ if ((BCMCPU_IS_6362() || BCMCPU_IS_6368() || BCMCPU_IS_63268()) && ++ !strcmp(id, "ipsec")) + return &clk_ipsec; +- if ((BCMCPU_IS_6328() || BCMCPU_IS_6362()) && !strcmp(id, "pcie")) ++ if ((BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) && ++ !strcmp(id, "pcie")) + return &clk_pcie; + return ERR_PTR(-ENOENT); + } +@@ -411,6 +427,7 @@ static int __init bcm63xx_clk_init(void) + clk_hsspi.rate = HSSPI_PLL_HZ_6328; + break; + case BCM6362_CPU_ID: ++ case BCM63268_CPU_ID: + clk_hsspi.rate = HSSPI_PLL_HZ_6362; + break; + } +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -101,6 +101,15 @@ static const int bcm6368_irqs[] = { + + }; + ++static const unsigned long bcm63268_regs_base[] = { ++ __GEN_CPU_REGS_TABLE(63268) ++}; ++ ++static const int bcm63268_irqs[] = { ++ __GEN_CPU_IRQ_TABLE(63268) ++ ++}; ++ + u32 bcm63xx_get_cpu_variant(void) + { + return bcm63xx_cpu_variant; +@@ -253,6 +262,27 @@ static unsigned int detect_cpu_clock(voi + + return (((64 * 1000000) / p1) * p2 * ndiv) / m1; + } ++ case BCM63268_CPU_ID: ++ { ++ unsigned int tmp, mips_pll_fcvo; ++ ++ tmp = bcm_misc_readl(MISC_STRAPBUS_63268_REG); ++ mips_pll_fcvo = (tmp & STRAPBUS_63268_FCVO_MASK) >> ++ STRAPBUS_63268_FCVO_SHIFT; ++ switch (mips_pll_fcvo) { ++ case 0x3: ++ case 0xe: ++ return 320000000; ++ case 0xa: ++ return 333000000; ++ case 0x2: ++ case 0xb: ++ case 0xf: ++ return 400000000; ++ default: ++ return 0; ++ } ++ } + + default: + panic("Failed to detect clock for CPU with id=%04X\n", cpu_id); +@@ -267,7 +297,7 @@ static unsigned int detect_memory_size(v + unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0; + u32 val; + +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) + return bcm_ddr_readl(DDR_CSEND_REG) << 24; + + if (BCMCPU_IS_6345()) { +@@ -305,6 +335,7 @@ void __init bcm63xx_cpu_init(void) + unsigned int tmp; + unsigned int cpu = smp_processor_id(); + u32 chipid_reg; ++ bool long_chipid = false; + u8 __maybe_unused varid = 0; + + /* soc registers location depends on cpu type */ +@@ -326,6 +357,9 @@ void __init bcm63xx_cpu_init(void) + case 0x10: + chipid_reg = BCM_6345_PERF_BASE; + break; ++ case 0x80: ++ long_chipid = true; ++ /* fall-through */ + default: + chipid_reg = BCM_6368_PERF_BASE; + break; +@@ -333,6 +367,7 @@ void __init bcm63xx_cpu_init(void) + break; + } + ++ + /* + * really early to panic, but delaying panic would not help since we + * will never get any working console +@@ -342,10 +377,17 @@ void __init bcm63xx_cpu_init(void) + + /* read out CPU type */ + tmp = bcm_readl(chipid_reg); +- bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT; +- bcm63xx_cpu_variant = bcm63xx_cpu_id; ++ ++ if (long_chipid) { ++ bcm63xx_cpu_id = tmp & REV_LONG_CHIPID_MASK; ++ bcm63xx_cpu_id >>= REV_LONG_CHIPID_SHIFT; ++ } else { ++ bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT; ++ varid = (tmp & REV_VARID_MASK) >> REV_VARID_SHIFT; ++ } ++ + bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT; +- varid = (tmp & REV_VARID_MASK) >> REV_VARID_SHIFT; ++ bcm63xx_cpu_variant = bcm63xx_cpu_id; + + switch (bcm63xx_cpu_id) { + case BCM3368_CPU_ID: +@@ -400,6 +442,15 @@ void __init bcm63xx_cpu_init(void) + /* BCM6369 is a BCM6368 without xDSL, so treat it the same */ + bcm63xx_cpu_id = BCM6368_CPU_ID; + break; ++ case BCM63168_CPU_ID: ++ case BCM63169_CPU_ID: ++ case BCM63268_CPU_ID: ++ case BCM63269_CPU_ID: ++ bcm63xx_regs_base = bcm63268_regs_base; ++ bcm63xx_irqs = bcm63268_irqs; ++ ++ bcm63xx_cpu_id = BCM63268_CPU_ID; ++ break; + default: + panic("unsupported broadcom CPU %x", bcm63xx_cpu_id); + break; +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -94,6 +94,12 @@ static int __init bcm63xx_detect_flash_t + case STRAPBUS_6368_BOOT_SEL_PARALLEL: + return BCM63XX_FLASH_TYPE_PARALLEL; + } ++ case BCM63268_CPU_ID: ++ val = bcm_misc_readl(MISC_STRAPBUS_63268_REG); ++ if (val & STRAPBUS_63268_BOOT_SEL_SERIAL) ++ return BCM63XX_FLASH_TYPE_SERIAL; ++ else ++ return BCM63XX_FLASH_TYPE_NAND; + default: + return -EINVAL; + } +--- a/arch/mips/bcm63xx/dev-spi.c ++++ b/arch/mips/bcm63xx/dev-spi.c +@@ -37,7 +37,7 @@ static __init void bcm63xx_spi_regs_init + if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) + bcm63xx_regs_spi = bcm6348_regs_spi; + if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || +- BCMCPU_IS_6362() || BCMCPU_IS_6368()) ++ BCMCPU_IS_6362() || BCMCPU_IS_6368() || BCMCPU_IS_63268()) + bcm63xx_regs_spi = bcm6358_regs_spi; + } + +@@ -85,7 +85,7 @@ int __init bcm63xx_spi_register(void) + } + + if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() || +- BCMCPU_IS_6368()) { ++ BCMCPU_IS_6368() || BCMCPU_IS_63268()) { + spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1; + spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE; + spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT; +--- a/arch/mips/bcm63xx/irq.c ++++ b/arch/mips/bcm63xx/irq.c +@@ -150,6 +150,20 @@ static void bcm63xx_init_irq(void) + ext_irqs[5] = BCM_6368_EXT_IRQ5; + ext_shift = 4; + break; ++ case BCM63268_CPU_ID: ++ l2_intc_bases[0] += PERF_IRQSTAT_63268_REG(0); ++ l2_intc_bases[1] += PERF_IRQSTAT_63268_REG(1); ++ l2_irq_count = 2; ++ l2_width = 4; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_63268; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_63268_EXT_IRQ0; ++ ext_irqs[1] = BCM_63268_EXT_IRQ1; ++ ext_irqs[2] = BCM_63268_EXT_IRQ2; ++ ext_irqs[3] = BCM_63268_EXT_IRQ3; ++ ext_shift = 4; ++ break; + default: + BUG(); + } +--- a/arch/mips/bcm63xx/reset.c ++++ b/arch/mips/bcm63xx/reset.c +@@ -125,6 +125,20 @@ + #define BCM6368_RESET_PCIE 0 + #define BCM6368_RESET_PCIE_EXT 0 + ++#define BCM63268_RESET_SPI SOFTRESET_63268_SPI_MASK ++#define BCM63268_RESET_ENET 0 ++#define BCM63268_RESET_USBH SOFTRESET_63268_USBH_MASK ++#define BCM63268_RESET_USBD SOFTRESET_63268_USBS_MASK ++#define BCM63268_RESET_DSL 0 ++#define BCM63268_RESET_SAR SOFTRESET_63268_SAR_MASK ++#define BCM63268_RESET_EPHY 0 ++#define BCM63268_RESET_ENETSW SOFTRESET_63268_ENETSW_MASK ++#define BCM63268_RESET_PCM SOFTRESET_63268_PCM_MASK ++#define BCM63268_RESET_MPI 0 ++#define BCM63268_RESET_PCIE (SOFTRESET_63268_PCIE_MASK | \ ++ SOFTRESET_63268_PCIE_CORE_MASK) ++#define BCM63268_RESET_PCIE_EXT SOFTRESET_63268_PCIE_EXT_MASK ++ + /* + * core reset bits + */ +@@ -156,6 +170,10 @@ static const u32 bcm6368_reset_bits[] = + __GEN_RESET_BITS_TABLE(6368) + }; + ++static const u32 bcm63268_reset_bits[] = { ++ __GEN_RESET_BITS_TABLE(63268) ++}; ++ + const u32 *bcm63xx_reset_bits; + static int reset_reg; + +@@ -182,6 +200,9 @@ static int __init bcm63xx_reset_bits_ini + } else if (BCMCPU_IS_6368()) { + reset_reg = PERF_SOFTRESET_6368_REG; + bcm63xx_reset_bits = bcm6368_reset_bits; ++ } else if (BCMCPU_IS_63268()) { ++ reset_reg = PERF_SOFTRESET_63268_REG; ++ bcm63xx_reset_bits = bcm63268_reset_bits; + } + + return 0; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -21,6 +21,10 @@ + #define BCM6362_CPU_ID 0x6362 + #define BCM6368_CPU_ID 0x6368 + #define BCM6369_CPU_ID 0x6369 ++#define BCM63168_CPU_ID 0x63168 ++#define BCM63169_CPU_ID 0x63169 ++#define BCM63268_CPU_ID 0x63268 ++#define BCM63269_CPU_ID 0x63269 + + void __init bcm63xx_cpu_init(void); + u32 bcm63xx_get_cpu_variant(void); +@@ -61,6 +65,10 @@ static inline u32 __pure __bcm63xx_get_c + #ifdef CONFIG_BCM63XX_CPU_6368 + case BCM6368_CPU_ID: + #endif ++ ++#ifdef CONFIG_BCM63XX_CPU_63268 ++ case BCM63268_CPU_ID: ++#endif + break; + default: + unreachable(); +@@ -86,6 +94,7 @@ static inline u32 __pure bcm63xx_get_cpu + #define BCMCPU_IS_6358() (bcm63xx_get_cpu_id() == BCM6358_CPU_ID) + #define BCMCPU_IS_6362() (bcm63xx_get_cpu_id() == BCM6362_CPU_ID) + #define BCMCPU_IS_6368() (bcm63xx_get_cpu_id() == BCM6368_CPU_ID) ++#define BCMCPU_IS_63268() (bcm63xx_get_cpu_id() == BCM63268_CPU_ID) + + #define BCMCPU_VARIANT_IS_3368() \ + (bcm63xx_get_cpu_variant() == BCM3368_CPU_ID) +@@ -109,6 +118,14 @@ static inline u32 __pure bcm63xx_get_cpu + (bcm63xx_get_cpu_variant() == BCM6368_CPU_ID) + #define BCMCPU_VARIANT_IS_6369() \ + (bcm63xx_get_cpu_variant() == BCM6369_CPU_ID) ++#define BCMCPU_VARIANT_IS_63168() \ ++ (bcm63xx_get_cpu_variant() == BCM63168_CPU_ID) ++#define BCMCPU_VARIANT_IS_63169() \ ++ (bcm63xx_get_cpu_variant() == BCM63169_CPU_ID) ++#define BCMCPU_VARIANT_IS_63268() \ ++ (bcm63xx_get_cpu_variant() == BCM63268_CPU_ID) ++#define BCMCPU_VARIANT_IS_63269() \ ++ (bcm63xx_get_cpu_variant() == BCM63269_CPU_ID) + + /* + * While registers sets are (mostly) the same across 63xx CPU, base +@@ -573,6 +590,52 @@ enum bcm63xx_regs_set { + #define BCM_6368_RNG_BASE (0xb0004180) + #define BCM_6368_MISC_BASE (0xdeadbeef) + ++/* ++ * 63268 register sets base address ++ */ ++#define BCM_63268_DSL_LMEM_BASE (0xdeadbeef) ++#define BCM_63268_PERF_BASE (0xb0000000) ++#define BCM_63268_TIMER_BASE (0xb0000080) ++#define BCM_63268_WDT_BASE (0xb000009c) ++#define BCM_63268_UART0_BASE (0xb0000180) ++#define BCM_63268_UART1_BASE (0xb00001a0) ++#define BCM_63268_GPIO_BASE (0xb00000c0) ++#define BCM_63268_SPI_BASE (0xb0000800) ++#define BCM_63268_HSSPI_BASE (0xb0001000) ++#define BCM_63268_UDC0_BASE (0xdeadbeef) ++#define BCM_63268_USBDMA_BASE (0xb000c800) ++#define BCM_63268_OHCI0_BASE (0xb0002600) ++#define BCM_63268_OHCI_PRIV_BASE (0xdeadbeef) ++#define BCM_63268_USBH_PRIV_BASE (0xb0002700) ++#define BCM_63268_USBD_BASE (0xb0002400) ++#define BCM_63268_MPI_BASE (0xdeadbeef) ++#define BCM_63268_PCMCIA_BASE (0xdeadbeef) ++#define BCM_63268_PCIE_BASE (0xb06e0000) ++#define BCM_63268_SDRAM_REGS_BASE (0xdeadbeef) ++#define BCM_63268_DSL_BASE (0xdeadbeef) ++#define BCM_63268_UBUS_BASE (0xdeadbeef) ++#define BCM_63268_ENET0_BASE (0xdeadbeef) ++#define BCM_63268_ENET1_BASE (0xdeadbeef) ++#define BCM_63268_ENETDMA_BASE (0xb000d800) ++#define BCM_63268_ENETDMAC_BASE (0xb000da00) ++#define BCM_63268_ENETDMAS_BASE (0xb000dc00) ++#define BCM_63268_ENETSW_BASE (0xb0700000) ++#define BCM_63268_EHCI0_BASE (0xb0002500) ++#define BCM_63268_SDRAM_BASE (0xdeadbeef) ++#define BCM_63268_MEMC_BASE (0xdeadbeef) ++#define BCM_63268_DDR_BASE (0xb0003000) ++#define BCM_63268_M2M_BASE (0xdeadbeef) ++#define BCM_63268_ATM_BASE (0xdeadbeef) ++#define BCM_63268_XTM_BASE (0xb0007000) ++#define BCM_63268_XTMDMA_BASE (0xb000b800) ++#define BCM_63268_XTMDMAC_BASE (0xdeadbeef) ++#define BCM_63268_XTMDMAS_BASE (0xdeadbeef) ++#define BCM_63268_PCM_BASE (0xb000b000) ++#define BCM_63268_PCMDMA_BASE (0xb000b800) ++#define BCM_63268_PCMDMAC_BASE (0xdeadbeef) ++#define BCM_63268_PCMDMAS_BASE (0xdeadbeef) ++#define BCM_63268_RNG_BASE (0xdeadbeef) ++#define BCM_63268_MISC_BASE (0xb0001800) + + extern const unsigned long *bcm63xx_regs_base; + +@@ -1041,6 +1104,73 @@ enum bcm63xx_irq { + #define BCM_6368_EXT_IRQ4 (IRQ_INTERNAL_BASE + 24) + #define BCM_6368_EXT_IRQ5 (IRQ_INTERNAL_BASE + 25) + ++/* ++ * 63268 irqs ++ */ ++#define BCM_63268_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) ++#define BCM_63268_VERY_HIGH_IRQ_BASE (BCM_63268_HIGH_IRQ_BASE + 32) ++ ++#define BCM_63268_TIMER_IRQ (IRQ_INTERNAL_BASE + 0) ++#define BCM_63268_SPI_IRQ (BCM_63268_VERY_HIGH_IRQ_BASE + 16) ++#define BCM_63268_UART0_IRQ (IRQ_INTERNAL_BASE + 5) ++#define BCM_63268_UART1_IRQ (BCM_63268_HIGH_IRQ_BASE + 2) ++#define BCM_63268_DSL_IRQ (IRQ_INTERNAL_BASE + 23) ++#define BCM_63268_UDC0_IRQ 0 ++#define BCM_63268_ENET0_IRQ 0 ++#define BCM_63268_ENET1_IRQ 0 ++#define BCM_63268_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 13) ++#define BCM_63268_HSSPI_IRQ (IRQ_INTERNAL_BASE + 6) ++#define BCM_63268_OHCI0_IRQ (IRQ_INTERNAL_BASE + 9) ++#define BCM_63268_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10) ++#define BCM_63268_USBD_IRQ (IRQ_INTERNAL_BASE + 11) ++#define BCM_63268_USBD_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 19) ++#define BCM_63268_USBD_TXDMA0_IRQ (BCM_63268_HIGH_IRQ_BASE + 4) ++#define BCM_63268_USBD_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 20) ++#define BCM_63268_USBD_TXDMA1_IRQ (BCM_63268_HIGH_IRQ_BASE + 5) ++#define BCM_63268_USBD_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 21) ++#define BCM_63268_USBD_TXDMA2_IRQ (BCM_63268_HIGH_IRQ_BASE + 6) ++#define BCM_63268_PCMCIA_IRQ 0 ++#define BCM_63268_ENET0_RXDMA_IRQ 0 ++#define BCM_63268_ENET0_TXDMA_IRQ 0 ++#define BCM_63268_ENET1_RXDMA_IRQ 0 ++#define BCM_63268_ENET1_TXDMA_IRQ 0 ++#define BCM_63268_PCI_IRQ (BCM_63268_HIGH_IRQ_BASE + 8) ++#define BCM_63268_ATM_IRQ 0 ++#define BCM_63268_ENETSW_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 1) ++#define BCM_63268_ENETSW_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 2) ++#define BCM_63268_ENETSW_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 3) ++#define BCM_63268_ENETSW_RXDMA3_IRQ (IRQ_INTERNAL_BASE + 4) ++#define BCM_63268_ENETSW_TXDMA0_IRQ (BCM_63268_VERY_HIGH_IRQ_BASE + 0) ++#define BCM_63268_ENETSW_TXDMA1_IRQ (BCM_63268_VERY_HIGH_IRQ_BASE + 1) ++#define BCM_63268_ENETSW_TXDMA2_IRQ (BCM_63268_VERY_HIGH_IRQ_BASE + 2) ++#define BCM_63268_ENETSW_TXDMA3_IRQ (BCM_63268_VERY_HIGH_IRQ_BASE + 3) ++#define BCM_63268_XTM_IRQ (BCM_63268_HIGH_IRQ_BASE + 17) ++#define BCM_63268_XTM_DMA0_IRQ (IRQ_INTERNAL_BASE + 26) ++ ++#define BCM_63268_RING_OSC_IRQ (BCM_63268_HIGH_IRQ_BASE + 20) ++#define BCM_63268_WLAN_GPIO_IRQ (BCM_63268_HIGH_IRQ_BASE + 3) ++#define BCM_63268_WLAN_IRQ (IRQ_INTERNAL_BASE + 7) ++#define BCM_63268_IPSEC_IRQ (IRQ_INTERNAL_BASE + 8) ++#define BCM_63268_NAND_IRQ (BCM_63268_HIGH_IRQ_BASE + 18) ++#define BCM_63268_PCM_IRQ (IRQ_INTERNAL_BASE + 13) ++#define BCM_63268_DG_IRQ (IRQ_INTERNAL_BASE + 15) ++#define BCM_63268_EPHY_ENERGY0_IRQ (IRQ_INTERNAL_BASE + 16) ++#define BCM_63268_EPHY_ENERGY1_IRQ (IRQ_INTERNAL_BASE + 17) ++#define BCM_63268_EPHY_ENERGY2_IRQ (IRQ_INTERNAL_BASE + 18) ++#define BCM_63268_EPHY_ENERGY3_IRQ (IRQ_INTERNAL_BASE + 19) ++#define BCM_63268_IPSEC_DMA0_IRQ (IRQ_INTERNAL_BASE + 22) ++#define BCM_63268_IPSEC_DMA1_IRQ (BCM_63268_HIGH_IRQ_BASE + 7) ++#define BCM_63268_FAP0_IRQ (IRQ_INTERNAL_BASE + 24) ++#define BCM_63268_FAP1_IRQ (IRQ_INTERNAL_BASE + 25) ++#define BCM_63268_PCM_DMA0_IRQ (BCM_63268_HIGH_IRQ_BASE + 10) ++#define BCM_63268_PCM_DMA1_IRQ (BCM_63268_HIGH_IRQ_BASE + 11) ++#define BCM_63268_DECT0_IRQ (BCM_63268_HIGH_IRQ_BASE + 0) ++#define BCM_63268_DECT1_IRQ (BCM_63268_HIGH_IRQ_BASE + 1) ++#define BCM_63268_EXT_IRQ0 (BCM_63268_HIGH_IRQ_BASE + 12) ++#define BCM_63268_EXT_IRQ1 (BCM_63268_HIGH_IRQ_BASE + 13) ++#define BCM_63268_EXT_IRQ2 (BCM_63268_HIGH_IRQ_BASE + 14) ++#define BCM_63268_EXT_IRQ3 (BCM_63268_HIGH_IRQ_BASE + 15) ++ + extern const int *bcm63xx_irqs; + + #define __GEN_CPU_IRQ_TABLE(__cpu) \ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h +@@ -22,6 +22,8 @@ static inline unsigned long bcm63xx_gpio + return 48; + case BCM6368_CPU_ID: + return 38; ++ case BCM63268_CPU_ID: ++ return 52; + case BCM6348_CPU_ID: + default: + return 37; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -9,6 +9,8 @@ + #define PERF_REV_REG 0x0 + #define REV_CHIPID_SHIFT 16 + #define REV_CHIPID_MASK (0xffff << REV_CHIPID_SHIFT) ++#define REV_LONG_CHIPID_SHIFT 12 ++#define REV_LONG_CHIPID_MASK (0xfffff << REV_LONG_CHIPID_SHIFT) + #define REV_VARID_SHIFT 12 + #define REV_VARID_MASK (0xf << REV_VARID_SHIFT) + #define REV_REVID_SHIFT 0 +@@ -211,6 +213,52 @@ + CKCTL_6368_NAND_EN | \ + CKCTL_6368_IPSEC_EN) + ++#define CKCTL_63268_DISABLE_GLESS (1 << 0) ++#define CKCTL_63268_VDSL_QPROC_EN (1 << 1) ++#define CKCTL_63268_VDSL_AFE_EN (1 << 2) ++#define CKCTL_63268_VDSL_EN (1 << 3) ++#define CKCTL_63268_MIPS_EN (1 << 4) ++#define CKCTL_63268_WLAN_OCP_EN (1 << 5) ++#define CKCTL_63268_DECT_EN (1 << 6) ++#define CKCTL_63268_FAP0_EN (1 << 7) ++#define CKCTL_63268_FAP1_EN (1 << 8) ++#define CKCTL_63268_SAR_EN (1 << 9) ++#define CKCTL_63268_ROBOSW_EN (1 << 10) ++#define CKCTL_63268_PCM_EN (1 << 11) ++#define CKCTL_63268_USBD_EN (1 << 12) ++#define CKCTL_63268_USBH_EN (1 << 13) ++#define CKCTL_63268_IPSEC_EN (1 << 14) ++#define CKCTL_63268_SPI_EN (1 << 15) ++#define CKCTL_63268_HSSPI_EN (1 << 16) ++#define CKCTL_63268_PCIE_EN (1 << 17) ++#define CKCTL_63268_PHYMIPS_EN (1 << 18) ++#define CKCTL_63268_GMAC_EN (1 << 19) ++#define CKCTL_63268_NAND_EN (1 << 20) ++#define CKCTL_63268_TBUS_EN (1 << 27) ++#define CKCTL_63268_ROBOSW250_EN (1 << 31) ++ ++#define CKCTL_63268_ALL_SAFE_EN (CKCTL_63268_VDSL_QPROC_EN | \ ++ CKCTL_63268_VDSL_AFE_EN | \ ++ CKCTL_63268_VDSL_EN | \ ++ CKCTL_63268_WLAN_OCP_EN | \ ++ CKCTL_63268_DECT_EN | \ ++ CKCTL_63268_FAP0_EN | \ ++ CKCTL_63268_FAP1_EN | \ ++ CKCTL_63268_SAR_EN | \ ++ CKCTL_63268_ROBOSW_EN | \ ++ CKCTL_63268_PCM_EN | \ ++ CKCTL_63268_USBD_EN | \ ++ CKCTL_63268_USBH_EN | \ ++ CKCTL_63268_IPSEC_EN | \ ++ CKCTL_63268_SPI_EN | \ ++ CKCTL_63268_HSSPI_EN | \ ++ CKCTL_63268_PCIE_EN | \ ++ CKCTL_63268_PHYMIPS_EN | \ ++ CKCTL_63268_GMAC_EN | \ ++ CKCTL_63268_NAND_EN | \ ++ CKCTL_63268_TBUS_EN | \ ++ CKCTL_63268_ROBOSW250_EN) ++ + /* System PLL Control register */ + #define PERF_SYS_PLL_CTL_REG 0x8 + #define SYS_PLL_SOFT_RESET 0x1 +@@ -224,6 +272,7 @@ + #define PERF_IRQMASK_6358_REG(x) (0xc + (x) * 0x2c) + #define PERF_IRQMASK_6362_REG(x) (0x20 + (x) * 0x10) + #define PERF_IRQMASK_6368_REG(x) (0x20 + (x) * 0x10) ++#define PERF_IRQMASK_63268_REG(x) (0x20 + (x) * 0x20) + + /* Interrupt Status register */ + #define PERF_IRQSTAT_3368_REG 0x10 +@@ -234,6 +283,7 @@ + #define PERF_IRQSTAT_6358_REG(x) (0x10 + (x) * 0x2c) + #define PERF_IRQSTAT_6362_REG(x) (0x28 + (x) * 0x10) + #define PERF_IRQSTAT_6368_REG(x) (0x28 + (x) * 0x10) ++#define PERF_IRQSTAT_63268_REG(x) (0x30 + (x) * 0x20) + + /* External Interrupt Configuration register */ + #define PERF_EXTIRQ_CFG_REG_3368 0x14 +@@ -244,6 +294,7 @@ + #define PERF_EXTIRQ_CFG_REG_6358 0x14 + #define PERF_EXTIRQ_CFG_REG_6362 0x18 + #define PERF_EXTIRQ_CFG_REG_6368 0x18 ++#define PERF_EXTIRQ_CFG_REG_63268 0x18 + + #define PERF_EXTIRQ_CFG_REG2_6358 0x1c + #define PERF_EXTIRQ_CFG_REG2_6368 0x1c +@@ -274,6 +325,7 @@ + #define PERF_SOFTRESET_6358_REG 0x34 + #define PERF_SOFTRESET_6362_REG 0x10 + #define PERF_SOFTRESET_6368_REG 0x10 ++#define PERF_SOFTRESET_63268_REG 0x10 + + #define SOFTRESET_3368_SPI_MASK (1 << 0) + #define SOFTRESET_3368_ENET_MASK (1 << 2) +@@ -367,6 +419,26 @@ + #define SOFTRESET_6368_USBH_MASK (1 << 12) + #define SOFTRESET_6368_PCM_MASK (1 << 13) + ++#define SOFTRESET_63268_SPI_MASK (1 << 0) ++#define SOFTRESET_63268_IPSEC_MASK (1 << 1) ++#define SOFTRESET_63268_EPHY_MASK (1 << 2) ++#define SOFTRESET_63268_SAR_MASK (1 << 3) ++#define SOFTRESET_63268_ENETSW_MASK (1 << 4) ++#define SOFTRESET_63268_USBS_MASK (1 << 5) ++#define SOFTRESET_63268_USBH_MASK (1 << 6) ++#define SOFTRESET_63268_PCM_MASK (1 << 7) ++#define SOFTRESET_63268_PCIE_CORE_MASK (1 << 8) ++#define SOFTRESET_63268_PCIE_MASK (1 << 9) ++#define SOFTRESET_63268_PCIE_EXT_MASK (1 << 10) ++#define SOFTRESET_63268_WLAN_SHIM_MASK (1 << 11) ++#define SOFTRESET_63268_DDR_PHY_MASK (1 << 12) ++#define SOFTRESET_63268_FAP0_MASK (1 << 13) ++#define SOFTRESET_63268_WLAN_UBUS_MASK (1 << 14) ++#define SOFTRESET_63268_DECT_MASK (1 << 15) ++#define SOFTRESET_63268_FAP1_MASK (1 << 16) ++#define SOFTRESET_63268_PCIE_HARD_MASK (1 << 17) ++#define SOFTRESET_63268_GPHY_MASK (1 << 18) ++ + /* MIPS PLL control register */ + #define PERF_MIPSPLLCTL_REG 0x34 + #define MIPSPLLCTL_N1_SHIFT 20 +@@ -1380,6 +1452,13 @@ + #define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15) + #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15) + ++#define MISC_STRAPBUS_63268_REG 0x14 ++#define STRAPBUS_63268_HSSPI_CLK_FAST (1 << 9) ++#define STRAPBUS_63268_BOOT_SEL_SERIAL (1 << 11) ++#define STRAPBUS_63268_BOOT_SEL_NAND (0 << 11) ++#define STRAPBUS_63268_FCVO_SHIFT 21 ++#define STRAPBUS_63268_FCVO_MASK (0xf << STRAPBUS_63268_FCVO_SHIFT) ++ + #define MISC_STRAPBUS_6328_REG 0x240 + #define STRAPBUS_6328_FCVO_SHIFT 7 + #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) +--- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h ++++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h +@@ -25,6 +25,7 @@ static inline int is_bcm63xx_internal_re + case BCM6328_CPU_ID: + case BCM6362_CPU_ID: + case BCM6368_CPU_ID: ++ case BCM63268_CPU_ID: + if (offset >= 0xb0000000 && offset < 0xb1000000) + return 1; + break; +--- a/arch/mips/bcm63xx/dev-hsspi.c ++++ b/arch/mips/bcm63xx/dev-hsspi.c +@@ -35,7 +35,7 @@ static struct platform_device bcm63xx_hs + + int __init bcm63xx_hsspi_register(void) + { +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362()) ++ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_63268()) + return -ENODEV; + + spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI); +--- a/arch/mips/bcm63xx/dev-enet.c ++++ b/arch/mips/bcm63xx/dev-enet.c +@@ -176,7 +176,8 @@ static int __init register_shared(void) + else + shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; + +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368() || ++ BCMCPU_IS_63268()) + chan_count = 32; + else if (BCMCPU_IS_6345()) + chan_count = 8; +@@ -276,7 +277,8 @@ bcm63xx_enetsw_register(const struct bcm + { + int ret; + +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) ++ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368() && ++ !BCMCPU_IS_63268()) + return -ENODEV; + + ret = register_shared(); +@@ -295,8 +297,11 @@ bcm63xx_enetsw_register(const struct bcm + + if (BCMCPU_IS_6328()) + enetsw_pd.num_ports = ENETSW_PORTS_6328; +- else if (BCMCPU_IS_6362() || BCMCPU_IS_6368()) ++ else if (BCMCPU_IS_6362() || BCMCPU_IS_6368() || ++ BCMCPU_VARIANT_IS_63168() || BCMCPU_VARIANT_IS_63169()) + enetsw_pd.num_ports = ENETSW_PORTS_6368; ++ else if (BCMCPU_VARIANT_IS_63268() || BCMCPU_VARIANT_IS_63269()) ++ enetsw_pd.num_ports = ENETSW_PORTS_63268; + + enetsw_pd.dma_has_sram = true; + enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h +@@ -62,6 +62,7 @@ struct bcm63xx_enet_platform_data { + #define ENETSW_MAX_PORT 8 + #define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */ + #define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */ ++#define ENETSW_PORTS_63268 8 /* 3 FE PHY + 1 GE PHY + 4 RGMII */ + + #define ENETSW_RGMII_PORT0 4 + diff --git a/target/linux/brcm63xx/patches-3.18/340-MIPS-BCM63XX-add-pcie-support-for-BCM63268.patch b/target/linux/brcm63xx/patches-3.18/340-MIPS-BCM63XX-add-pcie-support-for-BCM63268.patch new file mode 100644 index 0000000000..4e8a090791 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/340-MIPS-BCM63XX-add-pcie-support-for-BCM63268.patch @@ -0,0 +1,55 @@ +From 5c290c81dbdb4433600593fe80c88eb4af86e791 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 8 Dec 2013 03:22:40 +0100 +Subject: [PATCH 50/53] MIPS: BCM63XX: add pcie support for BCM63268 + +--- + arch/mips/bcm63xx/reset.c | 3 ++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h | 5 +++++ + arch/mips/pci/pci-bcm63xx.c | 4 ++++ + 3 files changed, 11 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/reset.c ++++ b/arch/mips/bcm63xx/reset.c +@@ -136,7 +136,8 @@ + #define BCM63268_RESET_PCM SOFTRESET_63268_PCM_MASK + #define BCM63268_RESET_MPI 0 + #define BCM63268_RESET_PCIE (SOFTRESET_63268_PCIE_MASK | \ +- SOFTRESET_63268_PCIE_CORE_MASK) ++ SOFTRESET_63268_PCIE_CORE_MASK | \ ++ SOFTRESET_63268_PCIE_HARD_MASK) + #define BCM63268_RESET_PCIE_EXT SOFTRESET_63268_PCIE_EXT_MASK + + /* +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h +@@ -45,6 +45,11 @@ + #define BCM_PCIE_MEM_END_PA_6328 (BCM_PCIE_MEM_BASE_PA_6328 + \ + BCM_PCIE_MEM_SIZE_6328 - 1) + ++#define BCM_PCIE_MEM_BASE_PA_63268 0x11000000 ++#define BCM_PCIE_MEM_SIZE_63268 (15 * 1024 * 1024) ++#define BCM_PCIE_MEM_END_PA_63268 (BCM_PCIE_MEM_BASE_PA_63268 + \ ++ BCM_PCIE_MEM_SIZE_63268 - 1) ++ + /* + * Internal registers are accessed through KSEG3 + */ +--- a/arch/mips/pci/pci-bcm63xx.c ++++ b/arch/mips/pci/pci-bcm63xx.c +@@ -337,11 +337,15 @@ static int __init bcm63xx_pci_init(void) + if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { + bcm_pcie_mem_resource.start = BCM_PCIE_MEM_BASE_PA_6328; + bcm_pcie_mem_resource.end = BCM_PCIE_MEM_END_PA_6328; ++ } else if (BCMCPU_IS_63268()) { ++ bcm_pcie_mem_resource.start = BCM_PCIE_MEM_BASE_PA_63268; ++ bcm_pcie_mem_resource.end = BCM_PCIE_MEM_END_PA_63268; + } + + switch (bcm63xx_get_cpu_id()) { + case BCM6328_CPU_ID: + case BCM6362_CPU_ID: ++ case BCM63268_CPU_ID: + return bcm63xx_register_pcie(); + case BCM3368_CPU_ID: + case BCM6348_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.18/341-MIPS-BCM63XX-add-support-for-BCM6318.patch b/target/linux/brcm63xx/patches-3.18/341-MIPS-BCM63XX-add-support-for-BCM6318.patch new file mode 100644 index 0000000000..440a30ead7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/341-MIPS-BCM63XX-add-support-for-BCM6318.patch @@ -0,0 +1,675 @@ +From 60c29522a8c77d96145d965589c56befda7d4c3d Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 8 Dec 2013 01:24:09 +0100 +Subject: [PATCH 51/53] MIPS: BCM63XX: add support for BCM6318 + +--- + arch/mips/bcm63xx/Kconfig | 5 + + arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- + arch/mips/bcm63xx/clk.c | 8 +- + arch/mips/bcm63xx/cpu.c | 53 +++++++++++ + arch/mips/bcm63xx/dev-flash.c | 3 + + arch/mips/bcm63xx/dev-spi.c | 2 +- + arch/mips/bcm63xx/irq.c | 10 ++ + arch/mips/bcm63xx/prom.c | 2 +- + arch/mips/bcm63xx/reset.c | 24 +++++ + arch/mips/bcm63xx/setup.c | 5 +- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 107 ++++++++++++++++++++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 75 ++++++++++++++- + arch/mips/include/asm/mach-bcm63xx/ioremap.h | 1 + + 13 files changed, 291 insertions(+), 6 deletions(-) + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -18,6 +18,11 @@ config BCM63XX_EHCI + select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD + select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD + ++config BCM63XX_CPU_6318 ++ bool "support 6318 CPU" ++ select SYS_HAS_CPU_BMIPS32_3300 ++ select HW_HAS_PCI ++ + config BCM63XX_CPU_6328 + bool "support 6328 CPU" + select SYS_HAS_CPU_BMIPS4350 +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -737,7 +737,7 @@ void __init board_prom_init(void) + /* read base address of boot chip select (0) + * 6328/6362 do not have MPI but boot from a fixed address + */ +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) { ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) { + val = 0x18000000; + } else { + val = bcm_mpi_readl(MPI_CSBASE_REG(0)); +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -252,7 +252,9 @@ static void hsspi_set(struct clk *clk, i + { + u32 mask; + +- if (BCMCPU_IS_6328()) ++ if (BCMCPU_IS_6318()) ++ mask = CKCTL_6318_HSSPI_EN; ++ else if (BCMCPU_IS_6328()) + mask = CKCTL_6328_HSSPI_EN; + else if (BCMCPU_IS_6362()) + mask = CKCTL_6362_HSSPI_EN; +@@ -417,12 +419,16 @@ void clk_put(struct clk *clk) + + EXPORT_SYMBOL(clk_put); + ++#define HSSPI_PLL_HZ_6318 250000000 + #define HSSPI_PLL_HZ_6328 133333333 + #define HSSPI_PLL_HZ_6362 400000000 + + static int __init bcm63xx_clk_init(void) + { + switch (bcm63xx_get_cpu_id()) { ++ case BCM6318_CPU_ID: ++ clk_hsspi.rate = HSSPI_PLL_HZ_6318; ++ break; + case BCM6328_CPU_ID: + clk_hsspi.rate = HSSPI_PLL_HZ_6328; + break; +--- a/arch/mips/bcm63xx/cpu.c ++++ b/arch/mips/bcm63xx/cpu.c +@@ -41,6 +41,14 @@ static const int bcm3368_irqs[] = { + __GEN_CPU_IRQ_TABLE(3368) + }; + ++static const unsigned long bcm6318_regs_base[] = { ++ __GEN_CPU_REGS_TABLE(6318) ++}; ++ ++static const int bcm6318_irqs[] = { ++ __GEN_CPU_IRQ_TABLE(6318) ++}; ++ + static const unsigned long bcm6328_regs_base[] = { + __GEN_CPU_REGS_TABLE(6328) + }; +@@ -134,6 +142,10 @@ unsigned int bcm63xx_get_memory_size(voi + return bcm63xx_memory_size; + } + ++#define STRAP_OVERRIDE_BUS_REG 0x0 ++#define OVERRIDE_BUS_MIPS_FREQ_SHIFT 23 ++#define OVERRIDE_BUS_MIPS_FREQ_MASK (0x3 << OVERRIDE_BUS_MIPS_FREQ_SHIFT) ++ + static unsigned int detect_cpu_clock(void) + { + u32 cpu_id = bcm63xx_get_cpu_id(); +@@ -142,6 +154,28 @@ static unsigned int detect_cpu_clock(voi + case BCM3368_CPU_ID: + return 300000000; + ++ case BCM6318_CPU_ID: ++ { ++ unsigned int tmp, mips_pll_fcvo; ++ ++ tmp = bcm_readl(BCM_6318_STRAP_BASE + STRAP_OVERRIDE_BUS_REG); ++ ++ pr_info("strap_override_bus = %08x\n", tmp); ++ ++ mips_pll_fcvo = (tmp & OVERRIDE_BUS_MIPS_FREQ_MASK) ++ >> OVERRIDE_BUS_MIPS_FREQ_SHIFT; ++ ++ switch (mips_pll_fcvo) { ++ case 0: ++ return 166000000; ++ case 1: ++ return 400000000; ++ case 2: ++ return 250000000; ++ case 3: ++ return 333000000; ++ }; ++ } + case BCM6328_CPU_ID: + { + unsigned int tmp, mips_pll_fcvo; +@@ -297,6 +331,13 @@ static unsigned int detect_memory_size(v + unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0; + u32 val; + ++ if (BCMCPU_IS_6318()) { ++ val = bcm_sdram_readl(SDRAM_CFG_REG); ++ val = val & SDRAM_CFG_6318_SPACE_MASK; ++ val >>= SDRAM_CFG_6318_SPACE_SHIFT; ++ return 1 << (val + 20); ++ } ++ + if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) + return bcm_ddr_readl(DDR_CSEND_REG) << 24; + +@@ -343,6 +384,12 @@ void __init bcm63xx_cpu_init(void) + + switch (current_cpu_type()) { + case CPU_BMIPS3300: ++ if ((read_c0_prid() & 0xff) >= 0x33) { ++ /* BCM6318 */ ++ chipid_reg = BCM_6368_PERF_BASE; ++ break; ++ } ++ + if ((read_c0_prid() & PRID_IMP_MASK) != PRID_IMP_BMIPS3300_ALT) + __cpu_name[cpu] = "Broadcom BCM6338"; + /* fall-through */ +@@ -390,6 +437,10 @@ void __init bcm63xx_cpu_init(void) + bcm63xx_cpu_variant = bcm63xx_cpu_id; + + switch (bcm63xx_cpu_id) { ++ case BCM6318_CPU_ID: ++ bcm63xx_regs_base = bcm6318_regs_base; ++ bcm63xx_irqs = bcm6318_irqs; ++ break; + case BCM3368_CPU_ID: + bcm63xx_regs_base = bcm3368_regs_base; + bcm63xx_irqs = bcm3368_irqs; +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -60,6 +60,9 @@ static int __init bcm63xx_detect_flash_t + u32 val; + + switch (bcm63xx_get_cpu_id()) { ++ case BCM6318_CPU_ID: ++ /* only support serial flash */ ++ return BCM63XX_FLASH_TYPE_SERIAL; + case BCM6328_CPU_ID: + val = bcm_misc_readl(MISC_STRAPBUS_6328_REG); + if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) +--- a/arch/mips/bcm63xx/dev-spi.c ++++ b/arch/mips/bcm63xx/dev-spi.c +@@ -70,7 +70,7 @@ static struct platform_device bcm63xx_sp + + int __init bcm63xx_spi_register(void) + { +- if (BCMCPU_IS_6328() || BCMCPU_IS_6345()) ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6345()) + return -ENODEV; + + spi_resources[0].start = bcm63xx_regset_address(RSET_SPI); +--- a/arch/mips/bcm63xx/irq.c ++++ b/arch/mips/bcm63xx/irq.c +@@ -49,6 +49,19 @@ static void bcm63xx_init_irq(void) + ext_irqs[3] = BCM_3368_EXT_IRQ3; + ext_shift = 4; + break; ++ case BCM6318_CPU_ID: ++ l2_intc_bases[0] += PERF_IRQMASK_6318_REG; ++ l2_irq_count = 1; ++ l2_width = 4; ++ ++ ext_intc_bases[0] += PERF_EXTIRQ_CFG_REG_6318; ++ ext_irq_count = 4; ++ ext_irqs[0] = BCM_6318_EXT_IRQ0; ++ ext_irqs[1] = BCM_6318_EXT_IRQ0; ++ ext_irqs[2] = BCM_6318_EXT_IRQ0; ++ ext_irqs[3] = BCM_6318_EXT_IRQ0; ++ ext_shift = 4; ++ break; + case BCM6328_CPU_ID: + l2_intc_bases[0] += PERF_IRQMASK_6328_REG(0); + l2_intc_bases[1] += PERF_IRQMASK_6328_REG(1); +--- a/arch/mips/bcm63xx/prom.c ++++ b/arch/mips/bcm63xx/prom.c +@@ -72,7 +72,7 @@ void __init prom_init(void) + + if (reg & OTP_6328_REG3_TP1_DISABLED) + bmips_smp_enabled = 0; +- } else if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) { ++ } else if (BCMCPU_IS_6318() || BCMCPU_IS_3368() || BCMCPU_IS_6358()) { + bmips_smp_enabled = 0; + } + +--- a/arch/mips/bcm63xx/reset.c ++++ b/arch/mips/bcm63xx/reset.c +@@ -43,6 +43,23 @@ + #define BCM3368_RESET_PCIE 0 + #define BCM3368_RESET_PCIE_EXT 0 + ++ ++#define BCM6318_RESET_SPI SOFTRESET_6318_SPI_MASK ++#define BCM6318_RESET_ENET 0 ++#define BCM6318_RESET_USBH SOFTRESET_6318_USBH_MASK ++#define BCM6318_RESET_USBD SOFTRESET_6318_USBS_MASK ++#define BCM6318_RESET_DSL 0 ++#define BCM6318_RESET_SAR SOFTRESET_6318_SAR_MASK ++#define BCM6318_RESET_EPHY SOFTRESET_6318_EPHY_MASK ++#define BCM6318_RESET_ENETSW SOFTRESET_6318_ENETSW_MASK ++#define BCM6318_RESET_PCM 0 ++#define BCM6318_RESET_MPI 0 ++#define BCM6318_RESET_PCIE \ ++ (SOFTRESET_6318_PCIE_MASK | \ ++ SOFTRESET_6318_PCIE_CORE_MASK | \ ++ SOFTRESET_6318_PCIE_HARD_MASK) ++#define BCM6318_RESET_PCIE_EXT SOFTRESET_6318_PCIE_EXT_MASK ++ + #define BCM6328_RESET_SPI SOFTRESET_6328_SPI_MASK + #define BCM6328_RESET_ENET 0 + #define BCM6328_RESET_USBH SOFTRESET_6328_USBH_MASK +@@ -147,6 +164,10 @@ static const u32 bcm3368_reset_bits[] = + __GEN_RESET_BITS_TABLE(3368) + }; + ++static const u32 bcm6318_reset_bits[] = { ++ __GEN_RESET_BITS_TABLE(6318) ++}; ++ + static const u32 bcm6328_reset_bits[] = { + __GEN_RESET_BITS_TABLE(6328) + }; +@@ -183,6 +204,9 @@ static int __init bcm63xx_reset_bits_ini + if (BCMCPU_IS_3368()) { + reset_reg = PERF_SOFTRESET_6358_REG; + bcm63xx_reset_bits = bcm3368_reset_bits; ++ } else if (BCMCPU_IS_6318()) { ++ reset_reg = PERF_SOFTRESET_6318_REG; ++ bcm63xx_reset_bits = bcm6318_reset_bits; + } else if (BCMCPU_IS_6328()) { + reset_reg = PERF_SOFTRESET_6328_REG; + bcm63xx_reset_bits = bcm6328_reset_bits; +--- a/arch/mips/bcm63xx/setup.c ++++ b/arch/mips/bcm63xx/setup.c +@@ -71,6 +71,9 @@ void bcm63xx_machine_reboot(void) + case BCM3368_CPU_ID: + perf_regs[0] = PERF_EXTIRQ_CFG_REG_3368; + break; ++ case BCM6318_CPU_ID: ++ perf_regs[0] = PERF_EXTIRQ_CFG_REG_6318; ++ break; + case BCM6328_CPU_ID: + perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328; + break; +@@ -110,7 +113,7 @@ void bcm63xx_machine_reboot(void) + bcm6348_a1_reboot(); + + printk(KERN_INFO "triggering watchdog soft-reset...\n"); +- if (BCMCPU_IS_6328()) { ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328()) { + bcm_wdt_writel(1, WDT_SOFTRESET_REG); + } else { + reg = bcm_perf_readl(PERF_SYS_PLL_CTL_REG); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h +@@ -10,6 +10,7 @@ + * arm mach-types) + */ + #define BCM3368_CPU_ID 0x3368 ++#define BCM6318_CPU_ID 0x6318 + #define BCM6328_CPU_ID 0x6328 + #define BCM63281_CPU_ID 0x63281 + #define BCM63283_CPU_ID 0x63283 +@@ -38,6 +39,10 @@ static inline u32 __pure __bcm63xx_get_c + case BCM3368_CPU_ID: + #endif + ++#ifdef CONFIG_BCM63XX_CPU_6318 ++ case BCM6318_CPU_ID: ++#endif ++ + #ifdef CONFIG_BCM63XX_CPU_6328 + case BCM6328_CPU_ID: + #endif +@@ -87,6 +92,7 @@ static inline u32 __pure bcm63xx_get_cpu + } + + #define BCMCPU_IS_3368() (bcm63xx_get_cpu_id() == BCM3368_CPU_ID) ++#define BCMCPU_IS_6318() (bcm63xx_get_cpu_id() == BCM6318_CPU_ID) + #define BCMCPU_IS_6328() (bcm63xx_get_cpu_id() == BCM6328_CPU_ID) + #define BCMCPU_IS_6338() (bcm63xx_get_cpu_id() == BCM6338_CPU_ID) + #define BCMCPU_IS_6345() (bcm63xx_get_cpu_id() == BCM6345_CPU_ID) +@@ -98,6 +104,8 @@ static inline u32 __pure bcm63xx_get_cpu + + #define BCMCPU_VARIANT_IS_3368() \ + (bcm63xx_get_cpu_variant() == BCM3368_CPU_ID) ++#define BCMCPU_VARIANT_IS_6318() \ ++ (bcm63xx_get_cpu_variant() == BCM6318_CPU_ID) + #define BCMCPU_VARIANT_IS_63281() \ + (bcm63xx_get_cpu_variant() == BCM63281_CPU_ID) + #define BCMCPU_VARIANT_IS_63283() \ +@@ -252,6 +260,56 @@ enum bcm63xx_regs_set { + #define BCM_3368_MISC_BASE (0xdeadbeef) + + /* ++ * 6318 register sets base address ++ */ ++#define BCM_6318_DSL_LMEM_BASE (0xdeadbeef) ++#define BCM_6318_PERF_BASE (0xb0000000) ++#define BCM_6318_TIMER_BASE (0xb0000040) ++#define BCM_6318_WDT_BASE (0xb0000068) ++#define BCM_6318_UART0_BASE (0xb0000100) ++#define BCM_6318_UART1_BASE (0xdeadbeef) ++#define BCM_6318_GPIO_BASE (0xb0000080) ++#define BCM_6318_SPI_BASE (0xdeadbeef) ++#define BCM_6318_HSSPI_BASE (0xb0003000) ++#define BCM_6318_UDC0_BASE (0xdeadbeef) ++#define BCM_6318_USBDMA_BASE (0xb0006800) ++#define BCM_6318_OHCI0_BASE (0xb0005100) ++#define BCM_6318_OHCI_PRIV_BASE (0xdeadbeef) ++#define BCM_6318_USBH_PRIV_BASE (0xb0005200) ++#define BCM_6318_USBD_BASE (0xb0006000) ++#define BCM_6318_MPI_BASE (0xdeadbeef) ++#define BCM_6318_PCMCIA_BASE (0xdeadbeef) ++#define BCM_6318_PCIE_BASE (0xb0010000) ++#define BCM_6318_SDRAM_REGS_BASE (0xdeadbeef) ++#define BCM_6318_DSL_BASE (0xdeadbeef) ++#define BCM_6318_UBUS_BASE (0xdeadbeef) ++#define BCM_6318_ENET0_BASE (0xdeadbeef) ++#define BCM_6318_ENET1_BASE (0xdeadbeef) ++#define BCM_6318_ENETDMA_BASE (0xb0088000) ++#define BCM_6318_ENETDMAC_BASE (0xb0088200) ++#define BCM_6318_ENETDMAS_BASE (0xb0088400) ++#define BCM_6318_ENETSW_BASE (0xb0080000) ++#define BCM_6318_EHCI0_BASE (0xb0005000) ++#define BCM_6318_SDRAM_BASE (0xb0004000) ++#define BCM_6318_MEMC_BASE (0xdeadbeef) ++#define BCM_6318_DDR_BASE (0xdeadbeef) ++#define BCM_6318_M2M_BASE (0xdeadbeef) ++#define BCM_6318_ATM_BASE (0xdeadbeef) ++#define BCM_6318_XTM_BASE (0xdeadbeef) ++#define BCM_6318_XTMDMA_BASE (0xb000c000) ++#define BCM_6318_XTMDMAC_BASE (0xdeadbeef) ++#define BCM_6318_XTMDMAS_BASE (0xdeadbeef) ++#define BCM_6318_PCM_BASE (0xdeadbeef) ++#define BCM_6318_PCMDMA_BASE (0xdeadbeef) ++#define BCM_6318_PCMDMAC_BASE (0xdeadbeef) ++#define BCM_6318_PCMDMAS_BASE (0xdeadbeef) ++#define BCM_6318_RNG_BASE (0xdeadbeef) ++#define BCM_6318_MISC_BASE (0xb0000280) ++#define BCM_6318_OTP_BASE (0xdeadbeef) ++ ++#define BCM_6318_STRAP_BASE (0xb0000900) ++ ++/* + * 6328 register sets base address + */ + #define BCM_6328_DSL_LMEM_BASE (0xdeadbeef) +@@ -774,6 +832,55 @@ enum bcm63xx_irq { + #define BCM_3368_EXT_IRQ2 (IRQ_INTERNAL_BASE + 27) + #define BCM_3368_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28) + ++/* ++ * 6318 irqs ++ */ ++#define BCM_6318_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32) ++#define BCM_6318_VERY_HIGH_IRQ_BASE (BCM_6318_HIGH_IRQ_BASE + 32) ++ ++#define BCM_6318_TIMER_IRQ (IRQ_INTERNAL_BASE + 31) ++#define BCM_6318_SPI_IRQ 0 ++#define BCM_6318_UART0_IRQ (IRQ_INTERNAL_BASE + 28) ++#define BCM_6318_UART1_IRQ 0 ++#define BCM_6318_DSL_IRQ (IRQ_INTERNAL_BASE + 21) ++#define BCM_6318_UDC0_IRQ 0 ++#define BCM_6318_ENET0_IRQ 0 ++#define BCM_6318_ENET1_IRQ 0 ++#define BCM_6318_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12) ++#define BCM_6318_HSSPI_IRQ (IRQ_INTERNAL_BASE + 29) ++#define BCM_6318_OHCI0_IRQ (BCM_6318_HIGH_IRQ_BASE + 9) ++#define BCM_6318_EHCI0_IRQ (BCM_6318_HIGH_IRQ_BASE + 10) ++#define BCM_6318_USBD_IRQ (IRQ_INTERNAL_BASE + 4) ++#define BCM_6318_USBD_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 5) ++#define BCM_6318_USBD_TXDMA0_IRQ (IRQ_INTERNAL_BASE + 6) ++#define BCM_6318_USBD_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 7) ++#define BCM_6318_USBD_TXDMA1_IRQ (IRQ_INTERNAL_BASE + 8) ++#define BCM_6318_USBD_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 9) ++#define BCM_6318_USBD_TXDMA2_IRQ (IRQ_INTERNAL_BASE + 10) ++#define BCM_6318_PCMCIA_IRQ 0 ++#define BCM_6318_ENET0_RXDMA_IRQ 0 ++#define BCM_6318_ENET0_TXDMA_IRQ 0 ++#define BCM_6318_ENET1_RXDMA_IRQ 0 ++#define BCM_6318_ENET1_TXDMA_IRQ 0 ++#define BCM_6318_PCI_IRQ (IRQ_INTERNAL_BASE + 23) ++#define BCM_6318_ATM_IRQ 0 ++#define BCM_6318_ENETSW_RXDMA0_IRQ (BCM_6318_HIGH_IRQ_BASE + 0) ++#define BCM_6318_ENETSW_RXDMA1_IRQ (BCM_6318_HIGH_IRQ_BASE + 1) ++#define BCM_6318_ENETSW_RXDMA2_IRQ (BCM_6318_HIGH_IRQ_BASE + 2) ++#define BCM_6318_ENETSW_RXDMA3_IRQ (BCM_6318_HIGH_IRQ_BASE + 3) ++#define BCM_6318_ENETSW_TXDMA0_IRQ (BCM_6318_VERY_HIGH_IRQ_BASE + 10) ++#define BCM_6318_ENETSW_TXDMA1_IRQ (BCM_6318_VERY_HIGH_IRQ_BASE + 11) ++#define BCM_6318_ENETSW_TXDMA2_IRQ (BCM_6318_VERY_HIGH_IRQ_BASE + 12) ++#define BCM_6318_ENETSW_TXDMA3_IRQ (BCM_6318_VERY_HIGH_IRQ_BASE + 13) ++#define BCM_6318_XTM_IRQ (BCM_6318_HIGH_IRQ_BASE + 31) ++#define BCM_6318_XTM_DMA0_IRQ (BCM_6318_HIGH_IRQ_BASE + 11) ++ ++#define BCM_6318_PCM_DMA0_IRQ (IRQ_INTERNAL_BASE + 2) ++#define BCM_6318_PCM_DMA1_IRQ (IRQ_INTERNAL_BASE + 3) ++#define BCM_6318_EXT_IRQ0 (IRQ_INTERNAL_BASE + 24) ++#define BCM_6318_EXT_IRQ1 (IRQ_INTERNAL_BASE + 25) ++#define BCM_6318_EXT_IRQ2 (IRQ_INTERNAL_BASE + 26) ++#define BCM_6318_EXT_IRQ3 (IRQ_INTERNAL_BASE + 27) + + /* + * 6328 irqs +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -52,6 +52,39 @@ + CKCTL_3368_EMUSB_EN | \ + CKCTL_3368_USBU_EN) + ++#define CKCTL_6318_ADSL_ASB_EN (1 << 0) ++#define CKCTL_6318_USB_ASB_EN (1 << 1) ++#define CKCTL_6318_MIPS_ASB_EN (1 << 2) ++#define CKCTL_6318_PCIE_ASB_EN (1 << 3) ++#define CKCTL_6318_PHYMIPS_ASB_EN (1 << 4) ++#define CKCTL_6318_ROBOSW_ASB_EN (1 << 5) ++#define CKCTL_6318_SAR_ASB_EN (1 << 6) ++#define CKCTL_6318_SDR_ASB_EN (1 << 7) ++#define CKCTL_6318_SWREG_ASB_EN (1 << 8) ++#define CKCTL_6318_PERIPH_ASB_EN (1 << 9) ++#define CKCTL_6318_CPUBUS160_EN (1 << 10) ++#define CKCTL_6318_ADSL_EN (1 << 11) ++#define CKCTL_6318_SAR125_EN (1 << 12) ++#define CKCTL_6318_MIPS_EN (1 << 13) ++#define CKCTL_6318_PCIE_EN (1 << 14) ++#define CKCTL_6318_ROBOSW250_EN (1 << 16) ++#define CKCTL_6318_ROBOSW025_EN (1 << 17) ++#define CKCTL_6318_SDR_EN (1 << 19) ++#define CKCTL_6318_USB_EN (1 << 20) /* both device and host */ ++#define CKCTL_6318_HSSPI_EN (1 << 25) ++#define CKCTL_6318_PCIE25_EN (1 << 27) ++#define CKCTL_6318_PHYMIPS_EN (1 << 28) ++#define CKCTL_6318_ADSL_AFE_EN (1 << 29) ++#define CKCTL_6318_ADSL_QPROC_EN (1 << 30) ++ ++#define CKCTL_6318_ALL_SAFE_EN (CKCTL_6318_PHYMIPS_EN | \ ++ CKCTL_6318_ADSL_QPROC_EN | \ ++ CKCTL_6318_ADSL_AFE_EN | \ ++ CKCTL_6318_ADSL_EN | \ ++ CKCTL_6318_SAR_EN | \ ++ CKCTL_6318_USB_EN | \ ++ CKCTL_6318_PCIE_EN) ++ + #define CKCTL_6328_PHYMIPS_EN (1 << 0) + #define CKCTL_6328_ADSL_QPROC_EN (1 << 1) + #define CKCTL_6328_ADSL_AFE_EN (1 << 2) +@@ -259,12 +292,27 @@ + CKCTL_63268_TBUS_EN | \ + CKCTL_63268_ROBOSW250_EN) + ++/* UBUS Clock Control register */ ++#define PERF_UB_CKCTL_REG 0x10 ++ ++#define UB_CKCTL_6318_ADSL_EN (1 << 0) ++#define UB_CKCTL_6318_ARB_EN (1 << 1) ++#define UB_CKCTL_6318_MIPS_EN (1 << 2) ++#define UB_CKCTL_6318_PCIE_EN (1 << 3) ++#define UB_CKCTL_6318_PERIPH_EN (1 << 4) ++#define UB_CKCTL_6318_PHYMIPS_EN (1 << 5) ++#define UB_CKCTL_6318_ROBOSW_EN (1 << 6) ++#define UB_CKCTL_6318_SAR_EN (1 << 7) ++#define UB_CKCTL_6318_SDR_EN (1 << 8) ++#define UB_CKCTL_6318_USB_EN (1 << 9) ++ + /* System PLL Control register */ + #define PERF_SYS_PLL_CTL_REG 0x8 + #define SYS_PLL_SOFT_RESET 0x1 + + /* Interrupt Mask register */ + #define PERF_IRQMASK_3368_REG 0xc ++#define PERF_IRQMASK_6318_REG 0x20 + #define PERF_IRQMASK_6328_REG(x) (0x20 + (x) * 0x10) + #define PERF_IRQMASK_6338_REG 0xc + #define PERF_IRQMASK_6345_REG 0xc +@@ -276,6 +324,7 @@ + + /* Interrupt Status register */ + #define PERF_IRQSTAT_3368_REG 0x10 ++#define PERF_IRQSTAT_6318_REG 0x30 + #define PERF_IRQSTAT_6328_REG(x) (0x28 + (x) * 0x10) + #define PERF_IRQSTAT_6338_REG 0x10 + #define PERF_IRQSTAT_6345_REG 0x10 +@@ -287,6 +336,7 @@ + + /* External Interrupt Configuration register */ + #define PERF_EXTIRQ_CFG_REG_3368 0x14 ++#define PERF_EXTIRQ_CFG_REG_6318 0x18 + #define PERF_EXTIRQ_CFG_REG_6328 0x18 + #define PERF_EXTIRQ_CFG_REG_6338 0x14 + #define PERF_EXTIRQ_CFG_REG_6345 0x14 +@@ -321,6 +371,7 @@ + + /* Soft Reset register */ + #define PERF_SOFTRESET_REG 0x28 ++#define PERF_SOFTRESET_6318_REG 0x10 + #define PERF_SOFTRESET_6328_REG 0x10 + #define PERF_SOFTRESET_6358_REG 0x34 + #define PERF_SOFTRESET_6362_REG 0x10 +@@ -334,6 +385,18 @@ + #define SOFTRESET_3368_USBS_MASK (1 << 11) + #define SOFTRESET_3368_PCM_MASK (1 << 13) + ++#define SOFTRESET_6318_SPI_MASK (1 << 0) ++#define SOFTRESET_6318_EPHY_MASK (1 << 1) ++#define SOFTRESET_6318_SAR_MASK (1 << 2) ++#define SOFTRESET_6318_ENETSW_MASK (1 << 3) ++#define SOFTRESET_6318_USBS_MASK (1 << 4) ++#define SOFTRESET_6318_USBH_MASK (1 << 5) ++#define SOFTRESET_6318_PCIE_CORE_MASK (1 << 6) ++#define SOFTRESET_6318_PCIE_MASK (1 << 7) ++#define SOFTRESET_6318_PCIE_EXT_MASK (1 << 8) ++#define SOFTRESET_6318_PCIE_HARD_MASK (1 << 9) ++#define SOFTRESET_6318_ADSL_MASK (1 << 10) ++ + #define SOFTRESET_6328_SPI_MASK (1 << 0) + #define SOFTRESET_6328_EPHY_MASK (1 << 1) + #define SOFTRESET_6328_SAR_MASK (1 << 2) +@@ -505,8 +568,17 @@ + #define TIMER_IRQSTAT_TIMER1_IR_EN (1 << 9) + #define TIMER_IRQSTAT_TIMER2_IR_EN (1 << 10) + ++#define TIMER_IRQMASK_6318_REG 0x0 ++#define TIMER_IRQSTAT_6318_REG 0x4 ++#define IRQSTATMASK_TIMER0 (1 << 0) ++#define IRQSTATMASK_TIMER1 (1 << 1) ++#define IRQSTATMASK_TIMER2 (1 << 2) ++#define IRQSTATMASK_TIMER3 (1 << 3) ++#define IRQSTATMASK_WDT (1 << 4) ++ + /* Timer control register */ + #define TIMER_CTLx_REG(x) (0x4 + (x * 4)) ++#define TIMER_CTRx_6318_REG(x) (0x8 + (x * 4)) + #define TIMER_CTL0_REG 0x4 + #define TIMER_CTL1_REG 0x8 + #define TIMER_CTL2_REG 0xC +@@ -1253,6 +1325,8 @@ + #define SDRAM_CFG_32B_MASK (1 << SDRAM_CFG_32B_SHIFT) + #define SDRAM_CFG_BANK_SHIFT 13 + #define SDRAM_CFG_BANK_MASK (1 << SDRAM_CFG_BANK_SHIFT) ++#define SDRAM_CFG_6318_SPACE_SHIFT 4 ++#define SDRAM_CFG_6318_SPACE_MASK (0xf << SDRAM_CFG_6318_SPACE_SHIFT) + + #define SDRAM_MBASE_REG 0xc + +--- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h ++++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h +@@ -22,6 +22,7 @@ static inline int is_bcm63xx_internal_re + if (offset >= 0xfff00000) + return 1; + break; ++ case BCM6318_CPU_ID: + case BCM6328_CPU_ID: + case BCM6362_CPU_ID: + case BCM6368_CPU_ID: +--- a/arch/mips/bcm63xx/dev-hsspi.c ++++ b/arch/mips/bcm63xx/dev-hsspi.c +@@ -35,7 +35,8 @@ static struct platform_device bcm63xx_hs + + int __init bcm63xx_hsspi_register(void) + { +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_63268()) ++ if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6362() && ++ !BCMCPU_IS_63268()) + return -ENODEV; + + spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI); +--- a/arch/mips/bcm63xx/dev-usb-usbd.c ++++ b/arch/mips/bcm63xx/dev-usb-usbd.c +@@ -41,7 +41,7 @@ int __init bcm63xx_usbd_register(const s + IRQ_USBD_RXDMA2, IRQ_USBD_TXDMA2 }; + int i; + +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6368()) ++ if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6368()) + return 0; + + usbd_resources[0].start = bcm63xx_regset_address(RSET_USBD); +--- a/arch/mips/bcm63xx/dev-enet.c ++++ b/arch/mips/bcm63xx/dev-enet.c +@@ -176,8 +176,8 @@ static int __init register_shared(void) + else + shared_res[0].end += (RSET_ENETDMA_SIZE) - 1; + +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368() || +- BCMCPU_IS_63268()) ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6362() || ++ BCMCPU_IS_6368() || BCMCPU_IS_63268()) + chan_count = 32; + else if (BCMCPU_IS_6345()) + chan_count = 8; +@@ -277,8 +277,8 @@ bcm63xx_enetsw_register(const struct bcm + { + int ret; + +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368() && +- !BCMCPU_IS_63268()) ++ if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6362() && ++ !BCMCPU_IS_6368() && !BCMCPU_IS_63268()) + return -ENODEV; + + ret = register_shared(); +@@ -295,7 +295,7 @@ bcm63xx_enetsw_register(const struct bcm + + memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof(*pd)); + +- if (BCMCPU_IS_6328()) ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328()) + enetsw_pd.num_ports = ENETSW_PORTS_6328; + else if (BCMCPU_IS_6362() || BCMCPU_IS_6368() || + BCMCPU_VARIANT_IS_63168() || BCMCPU_VARIANT_IS_63169()) +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h +@@ -9,6 +9,8 @@ int __init bcm63xx_gpio_init(void); + static inline unsigned long bcm63xx_gpio_count(void) + { + switch (bcm63xx_get_cpu_id()) { ++ case BCM6318_CPU_ID: ++ return 50; + case BCM6328_CPU_ID: + return 32; + case BCM3368_CPU_ID: +--- a/arch/mips/bcm63xx/dev-usb-ehci.c ++++ b/arch/mips/bcm63xx/dev-usb-ehci.c +@@ -81,7 +81,8 @@ static struct platform_device bcm63xx_eh + + int __init bcm63xx_ehci_register(void) + { +- if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) ++ if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() && ++ !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) + return 0; + + ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); diff --git a/target/linux/brcm63xx/patches-3.18/342-MIPS-BCM63XX-split-PCIe-reset-signals.patch b/target/linux/brcm63xx/patches-3.18/342-MIPS-BCM63XX-split-PCIe-reset-signals.patch new file mode 100644 index 0000000000..71044f846e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/342-MIPS-BCM63XX-split-PCIe-reset-signals.patch @@ -0,0 +1,156 @@ +From 4bdfacdeaf3c988c4f3256c88118893eac640b03 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 8 Dec 2013 14:17:50 +0100 +Subject: [PATCH 52/53] MIPS: BCM63XX: split PCIE reset signals + +--- + arch/mips/bcm63xx/reset.c | 39 ++++++++++++++-------- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h | 2 ++ + arch/mips/pci/pci-bcm63xx.c | 7 ++++ + 3 files changed, 34 insertions(+), 14 deletions(-) + +--- a/arch/mips/bcm63xx/reset.c ++++ b/arch/mips/bcm63xx/reset.c +@@ -28,7 +28,9 @@ + [BCM63XX_RESET_PCM] = BCM## __cpu ##_RESET_PCM, \ + [BCM63XX_RESET_MPI] = BCM## __cpu ##_RESET_MPI, \ + [BCM63XX_RESET_PCIE] = BCM## __cpu ##_RESET_PCIE, \ +- [BCM63XX_RESET_PCIE_EXT] = BCM## __cpu ##_RESET_PCIE_EXT, ++ [BCM63XX_RESET_PCIE_EXT] = BCM## __cpu ##_RESET_PCIE_EXT, \ ++ [BCM63XX_RESET_PCIE_CORE] = BCM## __cpu ##_RESET_PCIE_CORE, \ ++ [BCM63XX_RESET_PCIE_HARD] = BCM## __cpu ##_RESET_PCIE_HARD, + + #define BCM3368_RESET_SPI SOFTRESET_3368_SPI_MASK + #define BCM3368_RESET_ENET SOFTRESET_3368_ENET_MASK +@@ -42,6 +44,8 @@ + #define BCM3368_RESET_MPI SOFTRESET_3368_MPI_MASK + #define BCM3368_RESET_PCIE 0 + #define BCM3368_RESET_PCIE_EXT 0 ++#define BCM3368_RESET_PCIE_CORE 0 ++#define BCM3368_RESET_PCIE_HARD 0 + + + #define BCM6318_RESET_SPI SOFTRESET_6318_SPI_MASK +@@ -54,11 +58,10 @@ + #define BCM6318_RESET_ENETSW SOFTRESET_6318_ENETSW_MASK + #define BCM6318_RESET_PCM 0 + #define BCM6318_RESET_MPI 0 +-#define BCM6318_RESET_PCIE \ +- (SOFTRESET_6318_PCIE_MASK | \ +- SOFTRESET_6318_PCIE_CORE_MASK | \ +- SOFTRESET_6318_PCIE_HARD_MASK) ++#define BCM6318_RESET_PCIE SOFTRESET_6318_PCIE_MASK + #define BCM6318_RESET_PCIE_EXT SOFTRESET_6318_PCIE_EXT_MASK ++#define BCM6318_RESET_PCIE_CORE SOFTRESET_6318_PCIE_CORE_MASK ++#define BCM6318_RESET_PCIE_HARD SOFTRESET_6318_PCIE_HARD_MASK + + #define BCM6328_RESET_SPI SOFTRESET_6328_SPI_MASK + #define BCM6328_RESET_ENET 0 +@@ -70,11 +73,10 @@ + #define BCM6328_RESET_ENETSW SOFTRESET_6328_ENETSW_MASK + #define BCM6328_RESET_PCM SOFTRESET_6328_PCM_MASK + #define BCM6328_RESET_MPI 0 +-#define BCM6328_RESET_PCIE \ +- (SOFTRESET_6328_PCIE_MASK | \ +- SOFTRESET_6328_PCIE_CORE_MASK | \ +- SOFTRESET_6328_PCIE_HARD_MASK) ++#define BCM6328_RESET_PCIE SOFTRESET_6328_PCIE_MASK + #define BCM6328_RESET_PCIE_EXT SOFTRESET_6328_PCIE_EXT_MASK ++#define BCM6328_RESET_PCIE_CORE SOFTRESET_6328_PCIE_CORE_MASK ++#define BCM6328_RESET_PCIE_HARD SOFTRESET_6328_PCIE_HARD_MASK + + #define BCM6338_RESET_SPI SOFTRESET_6338_SPI_MASK + #define BCM6338_RESET_ENET SOFTRESET_6338_ENET_MASK +@@ -88,6 +90,8 @@ + #define BCM6338_RESET_MPI 0 + #define BCM6338_RESET_PCIE 0 + #define BCM6338_RESET_PCIE_EXT 0 ++#define BCM6338_RESET_PCIE_CORE 0 ++#define BCM6338_RESET_PCIE_HARD 0 + + #define BCM6348_RESET_SPI SOFTRESET_6348_SPI_MASK + #define BCM6348_RESET_ENET SOFTRESET_6348_ENET_MASK +@@ -101,6 +105,8 @@ + #define BCM6348_RESET_MPI 0 + #define BCM6348_RESET_PCIE 0 + #define BCM6348_RESET_PCIE_EXT 0 ++#define BCM6348_RESET_PCIE_CORE 0 ++#define BCM6348_RESET_PCIE_HARD 0 + + #define BCM6358_RESET_SPI SOFTRESET_6358_SPI_MASK + #define BCM6358_RESET_ENET SOFTRESET_6358_ENET_MASK +@@ -114,6 +120,8 @@ + #define BCM6358_RESET_MPI SOFTRESET_6358_MPI_MASK + #define BCM6358_RESET_PCIE 0 + #define BCM6358_RESET_PCIE_EXT 0 ++#define BCM6358_RESET_PCIE_CORE 0 ++#define BCM6358_RESET_PCIE_HARD 0 + + #define BCM6362_RESET_SPI SOFTRESET_6362_SPI_MASK + #define BCM6362_RESET_ENET 0 +@@ -125,9 +133,10 @@ + #define BCM6362_RESET_ENETSW SOFTRESET_6362_ENETSW_MASK + #define BCM6362_RESET_PCM SOFTRESET_6362_PCM_MASK + #define BCM6362_RESET_MPI 0 +-#define BCM6362_RESET_PCIE (SOFTRESET_6362_PCIE_MASK | \ +- SOFTRESET_6362_PCIE_CORE_MASK) ++#define BCM6362_RESET_PCIE SOFTRESET_6362_PCIE_MASK + #define BCM6362_RESET_PCIE_EXT SOFTRESET_6362_PCIE_EXT_MASK ++#define BCM6362_RESET_PCIE_CORE SOFTRESET_6362_PCIE_CORE_MASK ++#define BCM6362_RESET_PCIE_HARD 0 + + #define BCM6368_RESET_SPI SOFTRESET_6368_SPI_MASK + #define BCM6368_RESET_ENET 0 +@@ -141,6 +150,8 @@ + #define BCM6368_RESET_MPI SOFTRESET_6368_MPI_MASK + #define BCM6368_RESET_PCIE 0 + #define BCM6368_RESET_PCIE_EXT 0 ++#define BCM6368_RESET_PCIE_CORE 0 ++#define BCM6368_RESET_PCIE_HARD 0 + + #define BCM63268_RESET_SPI SOFTRESET_63268_SPI_MASK + #define BCM63268_RESET_ENET 0 +@@ -152,10 +163,10 @@ + #define BCM63268_RESET_ENETSW SOFTRESET_63268_ENETSW_MASK + #define BCM63268_RESET_PCM SOFTRESET_63268_PCM_MASK + #define BCM63268_RESET_MPI 0 +-#define BCM63268_RESET_PCIE (SOFTRESET_63268_PCIE_MASK | \ +- SOFTRESET_63268_PCIE_CORE_MASK | \ +- SOFTRESET_63268_PCIE_HARD_MASK) ++#define BCM63268_RESET_PCIE SOFTRESET_63268_PCIE_MASK + #define BCM63268_RESET_PCIE_EXT SOFTRESET_63268_PCIE_EXT_MASK ++#define BCM63268_RESET_PCIE_CORE SOFTRESET_63268_PCIE_CORE_MASK ++#define BCM63268_RESET_PCIE_HARD SOFTRESET_63268_PCIE_HARD_MASK + + /* + * core reset bits +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_reset.h +@@ -14,6 +14,8 @@ enum bcm63xx_core_reset { + BCM63XX_RESET_MPI, + BCM63XX_RESET_PCIE, + BCM63XX_RESET_PCIE_EXT, ++ BCM63XX_RESET_PCIE_CORE, ++ BCM63XX_RESET_PCIE_HARD, + }; + + void bcm63xx_core_set_reset(enum bcm63xx_core_reset, int reset); +--- a/arch/mips/pci/pci-bcm63xx.c ++++ b/arch/mips/pci/pci-bcm63xx.c +@@ -135,9 +135,16 @@ static void __init bcm63xx_reset_pcie(vo + + /* reset the PCIe core */ + bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_CORE, 1); + bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_EXT, 1); ++ if (BCMCPU_IS_6328() || BCMCPU_IS_63268()) { ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_HARD, 1); ++ mdelay(10); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_HARD, 0); ++ } + mdelay(10); + ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_CORE, 0); + bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 0); + mdelay(10); + diff --git a/target/linux/brcm63xx/patches-3.18/343-MIPS-BCM63XX-add-PCIe-support-for-BCM6318.patch b/target/linux/brcm63xx/patches-3.18/343-MIPS-BCM63XX-add-PCIe-support-for-BCM6318.patch new file mode 100644 index 0000000000..3ac08b471e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/343-MIPS-BCM63XX-add-PCIe-support-for-BCM6318.patch @@ -0,0 +1,342 @@ +From 11a8ab8dac4ef5d0d70199843043927edce1d4db Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 15 Dec 2013 20:47:34 +0100 +Subject: [PATCH 53/53] MIPS: BCM63XX: add PCIe support for BCM6318 + +--- + arch/mips/bcm63xx/clk.c | 25 ++++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h | 6 ++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 60 +++++++++++- + arch/mips/pci/ops-bcm63xx.c | 16 +++- + arch/mips/pci/pci-bcm63xx.c | 106 ++++++++++++++++++---- + 5 files changed, 184 insertions(+), 29 deletions(-) + +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -50,6 +50,18 @@ static void bcm_hwclock_set(u32 mask, in + bcm_perf_writel(reg, PERF_CKCTL_REG); + } + ++static void bcm_ub_hwclock_set(u32 mask, int enable) ++{ ++ u32 reg; ++ ++ reg = bcm_perf_readl(PERF_UB_CKCTL_REG); ++ if (enable) ++ reg |= mask; ++ else ++ reg &= ~mask; ++ bcm_perf_writel(reg, PERF_UB_CKCTL_REG); ++} ++ + /* + * Ethernet MAC "misc" clock: dma clocks and main clock on 6348 + */ +@@ -317,12 +329,17 @@ static struct clk clk_ipsec = { + + static void pcie_set(struct clk *clk, int enable) + { +- if (BCMCPU_IS_6328()) ++ if (BCMCPU_IS_6318()) { ++ bcm_hwclock_set(CKCTL_6318_PCIE_EN, enable); ++ bcm_hwclock_set(CKCTL_6318_PCIE25_EN, enable); ++ bcm_ub_hwclock_set(UB_CKCTL_6318_PCIE_EN, enable); ++ } else if (BCMCPU_IS_6328()) { + bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable); +- else if (BCMCPU_IS_6362()) ++ } else if (BCMCPU_IS_6362()) { + bcm_hwclock_set(CKCTL_6362_PCIE_EN, enable); +- else if (BCMCPU_IS_63268()) ++ } else if (BCMCPU_IS_63268()) { + bcm_hwclock_set(CKCTL_63268_PCIE_EN, enable); ++ } + } + + static struct clk clk_pcie = { +@@ -405,7 +422,7 @@ struct clk *clk_get(struct device *dev, + if ((BCMCPU_IS_6362() || BCMCPU_IS_6368() || BCMCPU_IS_63268()) && + !strcmp(id, "ipsec")) + return &clk_ipsec; +- if ((BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) && ++ if ((BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) && + !strcmp(id, "pcie")) + return &clk_pcie; + return ERR_PTR(-ENOENT); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_io.h +@@ -40,6 +40,12 @@ + #define BCM_CB_MEM_END_PA (BCM_CB_MEM_BASE_PA + \ + BCM_CB_MEM_SIZE - 1) + ++#define BCM_PCIE_MEM_BASE_PA_6318 0x10200000 ++#define BCM_PCIE_MEM_SIZE_6318 (1 * 1024 * 1024) ++#define BCM_PCIE_MEM_END_PA_6318 (BCM_PCIE_MEM_BASE_PA_6318 + \ ++ BCM_PCIE_MEM_SIZE_6318 - 1) ++ ++ + #define BCM_PCIE_MEM_BASE_PA_6328 0x10f00000 + #define BCM_PCIE_MEM_SIZE_6328 (1 * 1024 * 1024) + #define BCM_PCIE_MEM_END_PA_6328 (BCM_PCIE_MEM_BASE_PA_6328 + \ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -1543,6 +1543,17 @@ + * _REG relative to RSET_PCIE + *************************************************************************/ + ++#define PCIE_SPECIFIC_REG 0x188 ++#define SPECIFIC_ENDIAN_MODE_BAR1_SHIFT 0 ++#define SPECIFIC_ENDIAN_MODE_BAR1_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) ++#define SPECIFIC_ENDIAN_MODE_BAR2_SHIFT 2 ++#define SPECIFIC_ENDIAN_MODE_BAR2_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) ++#define SPECIFIC_ENDIAN_MODE_BAR3_SHIFT 4 ++#define SPECIFIC_ENDIAN_MODE_BAR3_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) ++#define SPECIFIC_ENDIAN_MODE_WORD_ALIGN 0 ++#define SPECIFIC_ENDIAN_MODE_HALFWORD_ALIGN 1 ++#define SPECIFIC_ENDIAN_MODE_BYTE_ALIGN 2 ++ + #define PCIE_CONFIG2_REG 0x408 + #define CONFIG2_BAR1_SIZE_EN 1 + #define CONFIG2_BAR1_SIZE_MASK 0xf +@@ -1588,7 +1599,54 @@ + #define PCIE_RC_INT_C (1 << 2) + #define PCIE_RC_INT_D (1 << 3) + +-#define PCIE_DEVICE_OFFSET 0x8000 ++#define PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG 0x400c ++#define C2P_MEM_WIN_ENDIAN_MODE_MASK 0x3 ++#define C2P_MEM_WIN_ENDIAN_NO_SWAP 0 ++#define C2P_MEM_WIN_ENDIAN_HALF_WORD_SWAP 1 ++#define C2P_MEM_WIN_ENDIAN_HALF_BYTE_SWAP 2 ++#define C2P_MEM_WIN_BASE_ADDR_SHIFT 20 ++#define C2P_MEM_WIN_BASE_ADDR_MASK (0xfff << C2P_MEM_WIN_BASE_ADDR_SHIFT) ++ ++#define PCIE_RC_BAR1_CONFIG_LO_REG 0x402c ++#define RC_BAR_CFG_LO_SIZE_256MB 0xd ++#define RC_BAR_CFG_LO_MATCH_ADDR_SHIFT 20 ++#define RC_BAR_CFG_LO_MATCH_ADDR_MASK (0xfff << RC_BAR_CFG_LO_MATCH_ADDR_SHIFT) ++ ++#define PCIE_CPU_2_PCIE_MEM_WIN0_BASELIMIT_REG 0x4070 ++#define C2P_BASELIMIT_LIMIT_SHIFT 20 ++#define C2P_BASELIMIT_LIMIT_MASK (0xfff << C2P_BASELIMIT_LIMIT_SHIFT) ++#define C2P_BASELIMIT_BASE_SHIFT 4 ++#define C2P_BASELIMIT_BASE_MASK (0xfff << C2P_BASELIMIT_BASE_SHIFT) ++ ++#define PCIE_UBUS_BAR1_CFG_REMAP_REG 0x4088 ++#define BAR1_CFG_REMAP_OFFSET_SHIFT 20 ++#define BAR1_CFG_REMAP_OFFSET_MASK (0xfff << BAR1_CFG_REMAP_OFFSET_SHIFT) ++#define BAR1_CFG_REMAP_ACCESS_EN 1 ++ ++#define PCIE_HARD_DEBUG_REG 0x4204 ++#define HARD_DEBUG_SERDES_IDDQ (1 << 23) ++ ++#define PCIE_CPU_INT1_MASK_CLEAR_REG 0x830c ++#define CPU_INT_PCIE_ERR_ATTN_CPU (1 << 0) ++#define CPU_INT_PCIE_INTA (1 << 1) ++#define CPU_INT_PCIE_INTB (1 << 2) ++#define CPU_INT_PCIE_INTC (1 << 3) ++#define CPU_INT_PCIE_INTD (1 << 4) ++#define CPU_INT_PCIE_INTR (1 << 5) ++#define CPU_INT_PCIE_NMI (1 << 6) ++#define CPU_INT_PCIE_UBUS (1 << 7) ++#define CPU_INT_IPI (1 << 8) ++ ++#define PCIE_EXT_CFG_INDEX_REG 0x8400 ++#define EXT_CFG_FUNC_NUM_SHIFT 12 ++#define EXT_CFG_FUNC_NUM_MASK (0x7 << EXT_CFG_FUNC_NUM_SHIFT) ++#define EXT_CFG_DEV_NUM_SHIFT 15 ++#define EXT_CFG_DEV_NUM_MASK (0xf << EXT_CFG_DEV_NUM_SHIFT) ++#define EXT_CFG_BUS_NUM_SHIFT 20 ++#define EXT_CFG_BUS_NUM_MASK (0xff << EXT_CFG_BUS_NUM_SHIFT) ++ ++#define PCIE_DEVICE_OFFSET_6318 0x9000 ++#define PCIE_DEVICE_OFFSET_6328 0x8000 + + /************************************************************************* + * _REG relative to RSET_OTP +--- a/arch/mips/pci/ops-bcm63xx.c ++++ b/arch/mips/pci/ops-bcm63xx.c +@@ -488,8 +488,12 @@ static int bcm63xx_pcie_read(struct pci_ + if (!bcm63xx_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + +- if (bus->number == PCIE_BUS_DEVICE) +- reg += PCIE_DEVICE_OFFSET; ++ if (bus->number == PCIE_BUS_DEVICE) { ++ if (BCMCPU_IS_6318()) ++ reg += PCIE_DEVICE_OFFSET_6318; ++ else ++ reg += PCIE_DEVICE_OFFSET_6328; ++ } + + data = bcm_pcie_readl(reg); + +@@ -508,8 +512,12 @@ static int bcm63xx_pcie_write(struct pci + if (!bcm63xx_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + +- if (bus->number == PCIE_BUS_DEVICE) +- reg += PCIE_DEVICE_OFFSET; ++ if (bus->number == PCIE_BUS_DEVICE) { ++ if (BCMCPU_IS_6318()) ++ reg += PCIE_DEVICE_OFFSET_6318; ++ else ++ reg += PCIE_DEVICE_OFFSET_6328; ++ } + + + data = bcm_pcie_readl(reg); +--- a/arch/mips/pci/pci-bcm63xx.c ++++ b/arch/mips/pci/pci-bcm63xx.c +@@ -118,7 +118,7 @@ static void bcm63xx_int_cfg_writel(u32 v + + void __iomem *pci_iospace_start; + +-static void __init bcm63xx_reset_pcie(void) ++static void __init bcm63xx_reset_pcie_gen1(void) + { + u32 val; + u32 reg; +@@ -152,20 +152,32 @@ static void __init bcm63xx_reset_pcie(vo + mdelay(200); + } + +-static struct clk *pcie_clk; +- +-static int __init bcm63xx_register_pcie(void) ++static void __init bcm63xx_reset_pcie_gen2(void) + { + u32 val; + +- /* enable clock */ +- pcie_clk = clk_get(NULL, "pcie"); +- if (IS_ERR_OR_NULL(pcie_clk)) +- return -ENODEV; ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_HARD, 0); + +- clk_prepare_enable(pcie_clk); ++ /* reset the PCIe core */ ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_EXT, 1); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_CORE, 1); ++ mdelay(10); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_EXT, 0); ++ mdelay(10); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 0); ++ mdelay(10); ++ val = bcm_pcie_readl(PCIE_HARD_DEBUG_REG); ++ val &= ~HARD_DEBUG_SERDES_IDDQ; ++ bcm_pcie_writel(val, PCIE_HARD_DEBUG_REG); ++ mdelay(10); ++ bcm63xx_core_set_reset(BCM63XX_RESET_PCIE_CORE, 0); ++ mdelay(200); ++} + +- bcm63xx_reset_pcie(); ++static void __init bcm63xx_init_pcie_gen1(void) ++{ ++ u32 val; + + /* configure the PCIe bridge */ + val = bcm_pcie_readl(PCIE_BRIDGE_OPT1_REG); +@@ -190,6 +202,65 @@ static int __init bcm63xx_register_pcie( + val |= OPT2_CFG_TYPE1_BD_SEL; + bcm_pcie_writel(val, PCIE_BRIDGE_OPT2_REG); + ++ /* set bar0 to little endian */ ++ val = (bcm_pcie_mem_resource.start >> 20) << BASEMASK_BASE_SHIFT; ++ val |= (bcm_pcie_mem_resource.end >> 20) << BASEMASK_MASK_SHIFT; ++ val |= BASEMASK_REMAP_EN; ++ bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_BASEMASK_REG); ++ ++ val = (bcm_pcie_mem_resource.start >> 20) << REBASE_ADDR_BASE_SHIFT; ++ bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_REBASE_ADDR_REG); ++} ++ ++static void __init bcm63xx_init_pcie_gen2(void) ++{ ++ u32 val; ++ ++ bcm_pcie_writel(CPU_INT_PCIE_INTA | CPU_INT_PCIE_INTB | ++ CPU_INT_PCIE_INTC | CPU_INT_PCIE_INTD, ++ PCIE_CPU_INT1_MASK_CLEAR_REG); ++ ++ val = bcm_pcie_mem_resource.end & C2P_BASELIMIT_LIMIT_MASK; ++ val |= (bcm_pcie_mem_resource.start >> C2P_BASELIMIT_LIMIT_SHIFT) << ++ C2P_BASELIMIT_BASE_SHIFT; ++ ++ bcm_pcie_writel(val, PCIE_CPU_2_PCIE_MEM_WIN0_BASELIMIT_REG); ++ ++ /* set bar0 to little endian */ ++ val = bcm_pcie_readl(PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG); ++ val |= bcm_pcie_mem_resource.start & C2P_MEM_WIN_BASE_ADDR_MASK; ++ val |= C2P_MEM_WIN_ENDIAN_HALF_BYTE_SWAP; ++ bcm_pcie_writel(val, PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG); ++ ++ bcm_pcie_writel(SPECIFIC_ENDIAN_MODE_BYTE_ALIGN, PCIE_SPECIFIC_REG); ++ bcm_pcie_writel(RC_BAR_CFG_LO_SIZE_256MB, PCIE_RC_BAR1_CONFIG_LO_REG); ++ bcm_pcie_writel(BAR1_CFG_REMAP_ACCESS_EN, PCIE_UBUS_BAR1_CFG_REMAP_REG); ++ ++ bcm_pcie_writel(PCIE_BUS_DEVICE << EXT_CFG_BUS_NUM_SHIFT, ++ PCIE_EXT_CFG_INDEX_REG); ++} ++ ++static struct clk *pcie_clk; ++ ++static int __init bcm63xx_register_pcie(void) ++{ ++ u32 val; ++ ++ /* enable clock */ ++ pcie_clk = clk_get(NULL, "pcie"); ++ if (IS_ERR_OR_NULL(pcie_clk)) ++ return -ENODEV; ++ ++ clk_prepare_enable(pcie_clk); ++ ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_63268()) { ++ bcm63xx_reset_pcie_gen1(); ++ bcm63xx_init_pcie_gen1(); ++ } else { ++ bcm63xx_reset_pcie_gen2(); ++ bcm63xx_init_pcie_gen2(); ++ } ++ + /* setup class code as bridge */ + val = bcm_pcie_readl(PCIE_IDVAL3_REG); + val &= ~IDVAL3_CLASS_CODE_MASK; +@@ -201,15 +272,6 @@ static int __init bcm63xx_register_pcie( + val &= ~CONFIG2_BAR1_SIZE_MASK; + bcm_pcie_writel(val, PCIE_CONFIG2_REG); + +- /* set bar0 to little endian */ +- val = (bcm_pcie_mem_resource.start >> 20) << BASEMASK_BASE_SHIFT; +- val |= (bcm_pcie_mem_resource.end >> 20) << BASEMASK_MASK_SHIFT; +- val |= BASEMASK_REMAP_EN; +- bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_BASEMASK_REG); +- +- val = (bcm_pcie_mem_resource.start >> 20) << REBASE_ADDR_BASE_SHIFT; +- bcm_pcie_writel(val, PCIE_BRIDGE_BAR0_REBASE_ADDR_REG); +- + register_pci_controller(&bcm63xx_pcie_controller); + + return 0; +@@ -341,7 +403,10 @@ static int __init bcm63xx_pci_init(void) + if (!bcm63xx_pci_enabled) + return -ENODEV; + +- if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { ++ if (BCMCPU_IS_6318()) { ++ bcm_pcie_mem_resource.start = BCM_PCIE_MEM_BASE_PA_6318; ++ bcm_pcie_mem_resource.end = BCM_PCIE_MEM_END_PA_6318; ++ } if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) { + bcm_pcie_mem_resource.start = BCM_PCIE_MEM_BASE_PA_6328; + bcm_pcie_mem_resource.end = BCM_PCIE_MEM_END_PA_6328; + } else if (BCMCPU_IS_63268()) { +@@ -350,6 +415,7 @@ static int __init bcm63xx_pci_init(void) + } + + switch (bcm63xx_get_cpu_id()) { ++ case BCM6318_CPU_ID: + case BCM6328_CPU_ID: + case BCM6362_CPU_ID: + case BCM63268_CPU_ID: diff --git a/target/linux/brcm63xx/patches-3.18/344-MIPS-BCM63XX-detect-flash-type-early-and-store-the-r.patch b/target/linux/brcm63xx/patches-3.18/344-MIPS-BCM63XX-detect-flash-type-early-and-store-the-r.patch new file mode 100644 index 0000000000..a91a29b16c --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/344-MIPS-BCM63XX-detect-flash-type-early-and-store-the-r.patch @@ -0,0 +1,74 @@ +From 9a97177b907330971aa7bf41855fafc2602e1c18 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 22 Dec 2013 12:26:57 +0100 +Subject: [PATCH 51/56] MIPS: BCM63XX: detect flash type early and store the + result + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/dev-flash.c | 10 +++++++--- + arch/mips/bcm63xx/prom.c | 4 ++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 ++ + 3 files changed, 13 insertions(+), 3 deletions(-) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -22,6 +22,8 @@ + #include <bcm63xx_regs.h> + #include <bcm63xx_io.h> + ++static int flash_type; ++ + static struct mtd_partition mtd_partitions[] = { + { + .name = "cfe", +@@ -108,13 +110,15 @@ static int __init bcm63xx_detect_flash_t + } + } + ++void __init bcm63xx_flash_detect(void) ++{ ++ flash_type = bcm63xx_detect_flash_type(); ++} ++ + int __init bcm63xx_flash_register(void) + { +- int flash_type; + u32 val; + +- flash_type = bcm63xx_detect_flash_type(); +- + switch (flash_type) { + case BCM63XX_FLASH_TYPE_PARALLEL: + /* read base address of boot chip select (0) */ +--- a/arch/mips/bcm63xx/prom.c ++++ b/arch/mips/bcm63xx/prom.c +@@ -18,6 +18,7 @@ + #include <bcm63xx_io.h> + #include <bcm63xx_regs.h> + #include <bcm63xx_gpio.h> ++#include <bcm63xx_dev_flash.h> + + void __init prom_init(void) + { +@@ -56,6 +57,9 @@ void __init prom_init(void) + /* register gpiochip */ + bcm63xx_gpio_init(); + ++ /* detect and setup flash access */ ++ bcm63xx_flash_detect(); ++ + /* do low level board init */ + board_prom_init(); + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h +@@ -7,6 +7,8 @@ enum { + BCM63XX_FLASH_TYPE_NAND, + }; + ++void bcm63xx_flash_detect(void); ++ + int __init bcm63xx_flash_register(void); + + #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.18/345-MIPS-BCM63XX-fixup-mapped-SPI-flash-access-on-boot.patch b/target/linux/brcm63xx/patches-3.18/345-MIPS-BCM63XX-fixup-mapped-SPI-flash-access-on-boot.patch new file mode 100644 index 0000000000..2b19600776 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/345-MIPS-BCM63XX-fixup-mapped-SPI-flash-access-on-boot.patch @@ -0,0 +1,63 @@ +From 1cacd0f7b0d35f8e3d3f8a69ecb3b5e436d6b9e8 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 22 Dec 2013 13:25:25 +0100 +Subject: [PATCH 52/56] MIPS: BCM63XX: fixup mapped SPI flash access on boot + +Some bootloaders leave the flash access in an invalid state with dual +read enabled; fix it by disabling it and falling back to simple fast +reads. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/dev-flash.c | 36 ++++++++++++++++++++++++++++++++++++ + 1 file changed, 36 insertions(+) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -110,9 +110,46 @@ static int __init bcm63xx_detect_flash_t + } + } + ++#define HSSPI_FLASH_CTRL_REG 0x14 ++#define FLASH_CTRL_READ_OPCODE_MASK 0xff ++#define FLASH_CTRL_ADDR_BYTES_MASK (0x3 << 8) ++#define FLASH_CTRL_ADDR_BYTES_2 (0 << 8) ++#define FLASH_CTRL_ADDR_BYTES_3 (1 << 8) ++#define FLASH_CTRL_ADDR_BYTES_4 (2 << 8) ++#define FLASH_CTRL_MB_EN (1 << 23) ++ + void __init bcm63xx_flash_detect(void) + { + flash_type = bcm63xx_detect_flash_type(); ++ ++ /* reduce flash mapping to single i/o reads for safety */ ++ if (flash_type == BCM63XX_FLASH_TYPE_SERIAL && ++ (BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6362() || ++ BCMCPU_IS_63268())) { ++ u32 val = bcm_rset_readl(RSET_HSSPI, HSSPI_FLASH_CTRL_REG); ++ ++ if (!(val & FLASH_CTRL_MB_EN)) ++ return; ++ ++ val &= ~FLASH_CTRL_MB_EN; ++ val &= ~FLASH_CTRL_READ_OPCODE_MASK; ++ ++ switch (val & FLASH_CTRL_ADDR_BYTES_MASK) { ++ case FLASH_CTRL_ADDR_BYTES_3: ++ val |= 0x0b; /* OPCODE_FAST_READ */ ++ break; ++ case FLASH_CTRL_ADDR_BYTES_4: ++ val |= 0x0c; /* OPCODE_FAST_READ_4B */ ++ break; ++ case FLASH_CTRL_ADDR_BYTES_2: ++ default: ++ pr_warn("unsupported address byte mode (%x), not fixing up\n", ++ val & FLASH_CTRL_ADDR_BYTES_MASK); ++ return; ++ } ++ ++ bcm_rset_writel(RSET_HSSPI, val, HSSPI_FLASH_CTRL_REG); ++ } + } + + int __init bcm63xx_flash_register(void) diff --git a/target/linux/brcm63xx/patches-3.18/346-MIPS-BCM63XX-USB-ENETSW-6318-clocks.patch b/target/linux/brcm63xx/patches-3.18/346-MIPS-BCM63XX-USB-ENETSW-6318-clocks.patch new file mode 100644 index 0000000000..384702c80f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/346-MIPS-BCM63XX-USB-ENETSW-6318-clocks.patch @@ -0,0 +1,56 @@ +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -136,7 +136,11 @@ static struct clk clk_ephy = { + */ + static void enetsw_set(struct clk *clk, int enable) + { +- if (BCMCPU_IS_6328()) ++ if (BCMCPU_IS_6318()) { ++ bcm_hwclock_set(CKCTL_6318_ROBOSW250_EN | ++ CKCTL_6318_ROBOSW025_EN, enable); ++ bcm_ub_hwclock_set(UB_CKCTL_6318_ROBOSW_EN, enable); ++ } else if (BCMCPU_IS_6328()) + bcm_hwclock_set(CKCTL_6328_ROBOSW_EN, enable); + else if (BCMCPU_IS_6362()) + bcm_hwclock_set(CKCTL_6362_ROBOSW_EN, enable); +@@ -183,18 +187,22 @@ static struct clk clk_pcm = { + */ + static void usbh_set(struct clk *clk, int enable) + { +- if (BCMCPU_IS_6328()) ++ if (BCMCPU_IS_6318()) { ++ bcm_hwclock_set(CKCTL_6318_USB_EN, enable); ++ bcm_ub_hwclock_set(UB_CKCTL_6318_USB_EN, enable); ++ } else if (BCMCPU_IS_6328()) { + bcm_hwclock_set(CKCTL_6328_USBH_EN, enable); +- else if (BCMCPU_IS_6348()) ++ } else if (BCMCPU_IS_6348()) { + bcm_hwclock_set(CKCTL_6348_USBH_EN, enable); +- else if (BCMCPU_IS_6362()) ++ } else if (BCMCPU_IS_6362()) { + bcm_hwclock_set(CKCTL_6362_USBH_EN, enable); +- else if (BCMCPU_IS_6368()) ++ } else if (BCMCPU_IS_6368()) { + bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); +- else if (BCMCPU_IS_63268()) ++ } else if (BCMCPU_IS_63268()) { + bcm_hwclock_set(CKCTL_63268_USBH_EN, enable); +- else ++ } else { + return; ++ } + + if (enable) + msleep(100); +@@ -405,9 +413,9 @@ struct clk *clk_get(struct device *dev, + return &clk_enetsw; + if (!strcmp(id, "ephy")) + return &clk_ephy; +- if (!strcmp(id, "usbh")) ++ if (!strcmp(id, "usbh") || (BCMCPU_IS_6318() && !strcmp(id, "usbd"))) + return &clk_usbh; +- if (!strcmp(id, "usbd")) ++ if (!strcmp(id, "usbd") && !BCMCPU_IS_6318()) + return &clk_usbd; + if (!strcmp(id, "spi")) + return &clk_spi; diff --git a/target/linux/brcm63xx/patches-3.18/347-MIPS-BCM6318-USB-support.patch b/target/linux/brcm63xx/patches-3.18/347-MIPS-BCM6318-USB-support.patch new file mode 100644 index 0000000000..904d0b7ab0 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/347-MIPS-BCM6318-USB-support.patch @@ -0,0 +1,124 @@ +--- a/arch/mips/bcm63xx/usb-common.c ++++ b/arch/mips/bcm63xx/usb-common.c +@@ -109,6 +109,27 @@ void bcm63xx_usb_priv_ohci_cfg_set(void) + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); + reg |= USBH_PRIV_SETUP_IOC_MASK; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } else if (BCMCPU_IS_6318()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); ++ reg |= USBH_PRIV_PLL_CTRL1_SUSP_EN; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6318_REG); ++ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6318_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); ++ reg &= ~USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SIM_CTRL_6318_REG); ++ reg |= USBH_PRIV_SIM_CTRL_LADDR_SEL; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SIM_CTRL_6318_REG); + } + + spin_unlock_irqrestore(&usb_priv_reg_lock, flags); +@@ -144,6 +165,27 @@ void bcm63xx_usb_priv_ehci_cfg_set(void) + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); + reg |= USBH_PRIV_SETUP_IOC_MASK; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } else if (BCMCPU_IS_6318()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); ++ reg |= USBH_PRIV_PLL_CTRL1_SUSP_EN; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6318_REG); ++ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6318_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); ++ reg &= ~USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SIM_CTRL_6318_REG); ++ reg |= USBH_PRIV_SIM_CTRL_LADDR_SEL; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SIM_CTRL_6318_REG); + } + + spin_unlock_irqrestore(&usb_priv_reg_lock, flags); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -681,6 +681,12 @@ + #define GPIO_MODE_6368_SPI_SSN4 (1 << 30) + #define GPIO_MODE_6368_SPI_SSN5 (1 << 31) + ++#define GPIO_PINMUX_SEL0_6318 0x1c ++#define GPIO_PINMUX_SEL0_GPIO13_SHIFT 26 ++#define GPIO_PINMUX_SEL0_GPIO13_MASK (0x3 << GPIO_PINMUX_SEL0_GPIO13_SHIFT) ++#define GPIO_PINMUX_SEL0_GPIO13_PWRON (1 << GPIO_PINMUX_SEL0_GPIO13_SHIFT) ++#define GPIO_PINMUX_SEL0_GPIO13_LED (2 << GPIO_PINMUX_SEL0_GPIO13_SHIFT) ++#define GPIO_PINMUX_SEL0_GPIO13_GPIO (3 << GPIO_PINMUX_SEL0_GPIO13_SHIFT) + + #define GPIO_PINMUX_OTHR_REG 0x24 + #define GPIO_PINMUX_OTHR_6328_USB_SHIFT 12 +@@ -999,6 +1005,7 @@ + + #define USBH_PRIV_SWAP_6358_REG 0x0 + #define USBH_PRIV_SWAP_6368_REG 0x1c ++#define USBH_PRIV_SWAP_6318_REG 0x0c + + #define USBH_PRIV_SWAP_USBD_SHIFT 6 + #define USBH_PRIV_SWAP_USBD_MASK (1 << USBH_PRIV_SWAP_USBD_SHIFT) +@@ -1024,6 +1031,13 @@ + #define USBH_PRIV_SETUP_IOC_SHIFT 4 + #define USBH_PRIV_SETUP_IOC_MASK (1 << USBH_PRIV_SETUP_IOC_SHIFT) + ++#define USBH_PRIV_SETUP_6318_REG 0x00 ++#define USBH_PRIV_PLL_CTRL1_6318_REG 0x04 ++#define USBH_PRIV_PLL_CTRL1_SUSP_EN (1 << 27) ++#define USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN (1 << 31) ++#define USBH_PRIV_SIM_CTRL_6318_REG 0x20 ++#define USBH_PRIV_SIM_CTRL_LADDR_SEL (1 << 5) ++ + + /************************************************************************* + * _REG relative to RSET_USBD +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -129,6 +129,15 @@ void __init board_early_setup(const stru + } + + bcm_gpio_writel(val, GPIO_MODE_REG); ++ ++#if IS_ENABLED(CONFIG_USB) ++ if (BCMCPU_IS_6318() && (board.has_ehci0 || board.has_ohci0)) { ++ val = bcm_gpio_readl(GPIO_PINMUX_SEL0_6318); ++ val &= ~GPIO_PINMUX_SEL0_GPIO13_MASK; ++ val |= GPIO_PINMUX_SEL0_GPIO13_PWRON; ++ bcm_gpio_writel(val, GPIO_PINMUX_SEL0_6318); ++ } ++#endif + } + + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -22,6 +22,8 @@ config BCM63XX_CPU_6318 + bool "support 6318 CPU" + select SYS_HAS_CPU_BMIPS32_3300 + select HW_HAS_PCI ++ select BCM63XX_OHCI ++ select BCM63XX_EHCI + + config BCM63XX_CPU_6328 + bool "support 6328 CPU" diff --git a/target/linux/brcm63xx/patches-3.18/348-MIPS-BCM63XX-fix-BCM63268-USB-clock.patch b/target/linux/brcm63xx/patches-3.18/348-MIPS-BCM63XX-fix-BCM63268-USB-clock.patch new file mode 100644 index 0000000000..c758163956 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/348-MIPS-BCM63XX-fix-BCM63268-USB-clock.patch @@ -0,0 +1,71 @@ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -586,6 +586,9 @@ + #define TIMER_CTL_MONOTONIC_MASK (1 << 30) + #define TIMER_CTL_ENABLE_MASK (1 << 31) + ++/* Clock reset control (63268 only) */ ++#define TIMER_CLK_RST_CTL_REG 0x2c ++#define CLK_RST_CTL_USB_REF_CLK_EN (1 << 18) + + /************************************************************************* + * _REG relative to RSET_WDT +@@ -1547,6 +1550,11 @@ + #define STRAPBUS_63268_FCVO_SHIFT 21 + #define STRAPBUS_63268_FCVO_MASK (0xf << STRAPBUS_63268_FCVO_SHIFT) + ++#define MISC_IDDQ_CTRL_6328_REG 0x48 ++#define MISC_IDDQ_CTRL_63268_REG 0x4c ++ ++#define IDDQ_CTRL_63268_USBH (1 << 4) ++ + #define MISC_STRAPBUS_6328_REG 0x240 + #define STRAPBUS_6328_FCVO_SHIFT 7 + #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) +--- a/arch/mips/bcm63xx/clk.c ++++ b/arch/mips/bcm63xx/clk.c +@@ -62,6 +62,26 @@ static void bcm_ub_hwclock_set(u32 mask, + bcm_perf_writel(reg, PERF_UB_CKCTL_REG); + } + ++static void bcm_misc_iddq_set(u32 mask, int enable) ++{ ++ u32 offset; ++ u32 reg; ++ ++ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) ++ offset = MISC_IDDQ_CTRL_6328_REG; ++ else if (BCMCPU_IS_63268()) ++ offset = MISC_IDDQ_CTRL_63268_REG; ++ else ++ return; ++ ++ reg = bcm_misc_readl(offset); ++ if (enable) ++ reg &= ~mask; ++ else ++ reg |= mask; ++ bcm_misc_writel(reg, offset); ++} ++ + /* + * Ethernet MAC "misc" clock: dma clocks and main clock on 6348 + */ +@@ -199,7 +219,17 @@ static void usbh_set(struct clk *clk, in + } else if (BCMCPU_IS_6368()) { + bcm_hwclock_set(CKCTL_6368_USBH_EN, enable); + } else if (BCMCPU_IS_63268()) { ++ u32 reg; ++ + bcm_hwclock_set(CKCTL_63268_USBH_EN, enable); ++ bcm_misc_iddq_set(IDDQ_CTRL_63268_USBH, enable); ++ bcm63xx_core_set_reset(BCM63XX_RESET_USBH, !enable); ++ reg = bcm_timer_readl(TIMER_CLK_RST_CTL_REG); ++ if (enable) ++ reg |= CLK_RST_CTL_USB_REF_CLK_EN; ++ else ++ reg &= ~CLK_RST_CTL_USB_REF_CLK_EN; ++ bcm_timer_writel(reg, TIMER_CLK_RST_CTL_REG); + } else { + return; + } diff --git a/target/linux/brcm63xx/patches-3.18/349-MIPS-BCM63XX-add-BCM63268-USB-support.patch b/target/linux/brcm63xx/patches-3.18/349-MIPS-BCM63XX-add-BCM63268-USB-support.patch new file mode 100644 index 0000000000..0b709915a7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/349-MIPS-BCM63XX-add-BCM63268-USB-support.patch @@ -0,0 +1,117 @@ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -1033,11 +1033,18 @@ + #define USBH_PRIV_SETUP_6368_REG 0x28 + #define USBH_PRIV_SETUP_IOC_SHIFT 4 + #define USBH_PRIV_SETUP_IOC_MASK (1 << USBH_PRIV_SETUP_IOC_SHIFT) ++#define USBH_PRIV_SETUP_IPP_SHIFT 5 ++#define USBH_PRIV_SETUP_IPP_MASK (1 << USBH_PRIV_SETUP_IPP_SHIFT) + + #define USBH_PRIV_SETUP_6318_REG 0x00 ++#define USBH_PRIV_PLL_CTRL1_6368_REG 0x18 + #define USBH_PRIV_PLL_CTRL1_6318_REG 0x04 +-#define USBH_PRIV_PLL_CTRL1_SUSP_EN (1 << 27) +-#define USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN (1 << 31) ++ ++#define USBH_PRIV_PLL_CTRL1_6318_SUSP_EN (1 << 27) ++#define USBH_PRIV_PLL_CTRL1_6318_IDDQ_PWRDN (1 << 31) ++#define USBH_PRIV_PLL_CTRL1_63268_IDDQ_PWRDN (1 << 9) ++#define USBH_PRIV_PLL_CTRL1_63268_PWRDN_DELAY (1 << 10) ++ + #define USBH_PRIV_SIM_CTRL_6318_REG 0x20 + #define USBH_PRIV_SIM_CTRL_LADDR_SEL (1 << 5) + +--- a/arch/mips/bcm63xx/Kconfig ++++ b/arch/mips/bcm63xx/Kconfig +@@ -72,6 +72,8 @@ config BCM63XX_CPU_63268 + bool "support 63268 CPU" + select SYS_HAS_CPU_BMIPS4350 + select HW_HAS_PCI ++ select BCM63XX_OHCI ++ select BCM63XX_EHCI + endmenu + + source "arch/mips/bcm63xx/boards/Kconfig" +--- a/arch/mips/bcm63xx/dev-usb-ehci.c ++++ b/arch/mips/bcm63xx/dev-usb-ehci.c +@@ -82,7 +82,7 @@ static struct platform_device bcm63xx_eh + int __init bcm63xx_ehci_register(void) + { + if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() && +- !BCMCPU_IS_6362() && !BCMCPU_IS_6368()) ++ !BCMCPU_IS_6362() && !BCMCPU_IS_6368() && !BCMCPU_IS_63268()) + return 0; + + ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); +--- a/arch/mips/bcm63xx/usb-common.c ++++ b/arch/mips/bcm63xx/usb-common.c +@@ -109,9 +109,24 @@ void bcm63xx_usb_priv_ohci_cfg_set(void) + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); + reg |= USBH_PRIV_SETUP_IOC_MASK; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } else if (BCMCPU_IS_63268()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); ++ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ reg &= ~USBH_PRIV_SETUP_IPP_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6368_REG); ++ reg &= ~(USBH_PRIV_PLL_CTRL1_63268_IDDQ_PWRDN | ++ USBH_PRIV_PLL_CTRL1_63268_PWRDN_DELAY); ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6368_REG); + } else if (BCMCPU_IS_6318()) { + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); +- reg |= USBH_PRIV_PLL_CTRL1_SUSP_EN; ++ reg |= USBH_PRIV_PLL_CTRL1_6318_SUSP_EN; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6318_REG); +@@ -124,7 +139,7 @@ void bcm63xx_usb_priv_ohci_cfg_set(void) + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); +- reg &= ~USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN; ++ reg &= ~USBH_PRIV_PLL_CTRL1_6318_IDDQ_PWRDN; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SIM_CTRL_6318_REG); +@@ -165,9 +180,24 @@ void bcm63xx_usb_priv_ehci_cfg_set(void) + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); + reg |= USBH_PRIV_SETUP_IOC_MASK; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ } else if (BCMCPU_IS_63268()) { ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG); ++ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK; ++ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG); ++ reg |= USBH_PRIV_SETUP_IOC_MASK; ++ reg &= ~USBH_PRIV_SETUP_IPP_MASK; ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG); ++ ++ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6368_REG); ++ reg &= ~(USBH_PRIV_PLL_CTRL1_63268_IDDQ_PWRDN | ++ USBH_PRIV_PLL_CTRL1_63268_PWRDN_DELAY); ++ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6368_REG); + } else if (BCMCPU_IS_6318()) { + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); +- reg |= USBH_PRIV_PLL_CTRL1_SUSP_EN; ++ reg |= USBH_PRIV_PLL_CTRL1_6318_SUSP_EN; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6318_REG); +@@ -180,7 +210,7 @@ void bcm63xx_usb_priv_ehci_cfg_set(void) + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_PLL_CTRL1_6318_REG); +- reg &= ~USBH_PRIV_PLL_CTRL1_IDDQ_PWRDN; ++ reg &= ~USBH_PRIV_PLL_CTRL1_6318_IDDQ_PWRDN; + bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_PLL_CTRL1_6318_REG); + + reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SIM_CTRL_6318_REG); diff --git a/target/linux/brcm63xx/patches-3.18/350-MIPS-BCM63XX-support-settings-num-usbh-ports.patch b/target/linux/brcm63xx/patches-3.18/350-MIPS-BCM63XX-support-settings-num-usbh-ports.patch new file mode 100644 index 0000000000..41747da2d9 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/350-MIPS-BCM63XX-support-settings-num-usbh-ports.patch @@ -0,0 +1,107 @@ +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -42,6 +42,7 @@ struct board_info { + + /* USB config */ + struct bcm63xx_usbd_platform_data usbd; ++ unsigned int num_usbh_ports:2; + + /* DSP config */ + struct bcm63xx_dsp_platform_data dsp; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h +@@ -1,6 +1,6 @@ + #ifndef BCM63XX_DEV_USB_EHCI_H_ + #define BCM63XX_DEV_USB_EHCI_H_ + +-int bcm63xx_ehci_register(void); ++int bcm63xx_ehci_register(unsigned int num_ports); + + #endif /* BCM63XX_DEV_USB_EHCI_H_ */ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h +@@ -1,6 +1,6 @@ + #ifndef BCM63XX_DEV_USB_OHCI_H_ + #define BCM63XX_DEV_USB_OHCI_H_ + +-int bcm63xx_ohci_register(void); ++int bcm63xx_ohci_register(unsigned int num_ports); + + #endif /* BCM63XX_DEV_USB_OHCI_H_ */ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -181,6 +181,7 @@ int __init board_register_devices(void) + { + int button_count = 0; + int led_count = 0; ++ int usbh_ports = 0; + + if (board.has_uart0) + bcm63xx_uart_register(0); +@@ -203,14 +204,21 @@ int __init board_register_devices(void) + !board_get_mac_address(board.enetsw.mac_addr)) + bcm63xx_enetsw_register(&board.enetsw); + ++ if ((board.has_ohci0 || board.has_ehci0)) { ++ usbh_ports = board.num_usbh_ports; ++ ++ if (!usbh_ports || WARN_ON(usbh_ports > 1 && board.has_usbd)) ++ usbh_ports = 1; ++ } ++ + if (board.has_usbd) + bcm63xx_usbd_register(&board.usbd); + + if (board.has_ehci0) +- bcm63xx_ehci_register(); ++ bcm63xx_ehci_register(usbh_ports); + + if (board.has_ohci0) +- bcm63xx_ohci_register(); ++ bcm63xx_ohci_register(usbh_ports); + + if (board.has_dsp) + bcm63xx_dsp_register(&board.dsp); +--- a/arch/mips/bcm63xx/dev-usb-ehci.c ++++ b/arch/mips/bcm63xx/dev-usb-ehci.c +@@ -79,12 +79,14 @@ static struct platform_device bcm63xx_eh + }, + }; + +-int __init bcm63xx_ehci_register(void) ++int __init bcm63xx_ehci_register(unsigned int num_ports) + { + if (!BCMCPU_IS_6318() && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() && + !BCMCPU_IS_6362() && !BCMCPU_IS_6368() && !BCMCPU_IS_63268()) + return 0; + ++ bcm63xx_ehci_pdata.num_ports = num_ports; ++ + ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0); + ehci_resources[0].end = ehci_resources[0].start; + ehci_resources[0].end += RSET_EHCI_SIZE - 1; +--- a/arch/mips/bcm63xx/dev-usb-ohci.c ++++ b/arch/mips/bcm63xx/dev-usb-ohci.c +@@ -62,7 +62,6 @@ static struct usb_ohci_pdata bcm63xx_ohc + .big_endian_desc = 1, + .big_endian_mmio = 1, + .no_big_frame_no = 1, +- .num_ports = 1, + .power_on = bcm63xx_ohci_power_on, + .power_off = bcm63xx_ohci_power_off, + .power_suspend = bcm63xx_ohci_power_off, +@@ -80,11 +79,13 @@ static struct platform_device bcm63xx_oh + }, + }; + +-int __init bcm63xx_ohci_register(void) ++int __init bcm63xx_ohci_register(unsigned int num_ports) + { + if (BCMCPU_IS_6345() || BCMCPU_IS_6338()) + return -ENODEV; + ++ bcm63xx_ohci_pdata.num_ports = num_ports; ++ + ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0); + ohci_resources[0].end = ohci_resources[0].start; + ohci_resources[0].end += RSET_OHCI_SIZE - 1; diff --git a/target/linux/brcm63xx/patches-3.18/351-set-board-usbh-ports.patch b/target/linux/brcm63xx/patches-3.18/351-set-board-usbh-ports.patch new file mode 100644 index 0000000000..804cb85f20 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/351-set-board-usbh-ports.patch @@ -0,0 +1,10 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -616,6 +616,7 @@ static struct board_info __initdata boar + .has_ohci0 = 1, + .has_pccard = 1, + .has_ehci0 = 1, ++ .num_usbh_ports = 2, + + .leds = { + { diff --git a/target/linux/brcm63xx/patches-3.18/354-MIPS-BCM63XX-allow-building-support-for-more-than-on.patch b/target/linux/brcm63xx/patches-3.18/354-MIPS-BCM63XX-allow-building-support-for-more-than-on.patch new file mode 100644 index 0000000000..b6bcdae5d7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/354-MIPS-BCM63XX-allow-building-support-for-more-than-on.patch @@ -0,0 +1,95 @@ +From 0daf361ea799fba0af5a232036d0f06cea85ad24 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sat, 21 Jun 2014 12:47:49 +0200 +Subject: [PATCH 42/44] MIPS: BCM63XX: allow building support for more than one + board type + +Use the arguments passed to the kernel to detect being booted with +CFE as the indicator for bcm963xx board support, allowing the +non presence of CFE_EPTSEAL to assume a different board type. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/Kconfig | 7 +++---- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +- + arch/mips/bcm63xx/boards/board_common.c | 13 +++++++++++++ + arch/mips/bcm63xx/boards/board_common.h | 6 ++++++ + 4 files changed, 23 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/boards/Kconfig ++++ b/arch/mips/bcm63xx/boards/Kconfig +@@ -1,11 +1,10 @@ +-choice +- prompt "Board support" ++menu "Board support" + depends on BCM63XX +- default BOARD_BCM963XX + + config BOARD_BCM963XX + bool "Generic Broadcom 963xx boards" + select SSB ++ default y + help + +-endchoice ++endmenu +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -726,7 +726,7 @@ static const struct board_info __initcon + /* + * early init callback, read nvram data from flash and checksum it + */ +-void __init board_prom_init(void) ++void __init board_bcm963xx_init(void) + { + unsigned int i; + u8 *boot_addr, *cfe; +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -15,6 +15,8 @@ + #include <linux/gpio_keys.h> + #include <linux/spi/spi.h> + #include <asm/addrspace.h> ++#include <asm/bootinfo.h> ++#include <asm/fw/cfe/cfe_api.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> + #include <bcm63xx_dev_uart.h> +@@ -32,6 +34,8 @@ + #include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> + ++#include "board_common.h" ++ + #define PFX "board: " + + #define BCM963XX_KEYS_POLL_INTERVAL 20 +@@ -84,6 +88,15 @@ const char *board_get_name(void) + return board.name; + } + ++void __init board_prom_init(void) ++{ ++ /* detect bootloader */ ++ if (fw_arg3 == CFE_EPTSEAL) ++ board_bcm963xx_init(); ++ else ++ panic("unsupported bootloader detected"); ++} ++ + static int (*board_get_mac_address)(u8 mac[ETH_ALEN]); + + /* +--- a/arch/mips/bcm63xx/boards/board_common.h ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -6,4 +6,10 @@ + void board_early_setup(const struct board_info *board, + int (*get_mac_address)(u8 mac[ETH_ALEN])); + ++#if defined(CONFIG_BOARD_BCM963XX) ++void board_bcm963xx_init(void); ++#else ++static inline void board_bcm963xx_init(void) { } ++#endif ++ + #endif /* __BOARD_COMMON_H */ diff --git a/target/linux/brcm63xx/patches-3.18/355-MIPS-BCM63XX-allow-board-implementations-to-force-fl.patch b/target/linux/brcm63xx/patches-3.18/355-MIPS-BCM63XX-allow-board-implementations-to-force-fl.patch new file mode 100644 index 0000000000..7e408f69fb --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/355-MIPS-BCM63XX-allow-board-implementations-to-force-fl.patch @@ -0,0 +1,61 @@ +From 8a30097a899b975709f728666d5ad20c8b832d21 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Mar 2014 04:28:14 +0100 +Subject: [PATCH 43/44] MIPS: BCM63XX: allow board implementations to force + flash address + +Allow board implementations to force the physmap address. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/dev-flash.c | 19 ++++++++++++++----- + .../mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 ++ + 2 files changed, 16 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -57,6 +57,12 @@ static struct platform_device mtd_dev = + }, + }; + ++void __init bcm63xx_flash_force_phys_base_address(u32 start, u32 end) ++{ ++ mtd_resources[0].start = start; ++ mtd_resources[0].end = end; ++} ++ + static int __init bcm63xx_detect_flash_type(void) + { + u32 val; +@@ -158,12 +164,15 @@ int __init bcm63xx_flash_register(void) + + switch (flash_type) { + case BCM63XX_FLASH_TYPE_PARALLEL: +- /* read base address of boot chip select (0) */ +- val = bcm_mpi_readl(MPI_CSBASE_REG(0)); +- val &= MPI_CSBASE_BASE_MASK; + +- mtd_resources[0].start = val; +- mtd_resources[0].end = 0x1FFFFFFF; ++ if (!mtd_resources[0].start) { ++ /* read base address of boot chip select (0) */ ++ val = bcm_mpi_readl(MPI_CSBASE_REG(0)); ++ val &= MPI_CSBASE_BASE_MASK; ++ ++ mtd_resources[0].start = val; ++ mtd_resources[0].end = 0x1FFFFFFF; ++ } + + return platform_device_register(&mtd_dev); + case BCM63XX_FLASH_TYPE_SERIAL: +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h +@@ -9,6 +9,8 @@ enum { + + void bcm63xx_flash_detect(void); + ++void bcm63xx_flash_force_phys_base_address(u32 start, u32 end); ++ + int __init bcm63xx_flash_register(void); + + #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.18/356-MIPS-BCM63XX-move-fallback-sprom-support-into-its-ow.patch b/target/linux/brcm63xx/patches-3.18/356-MIPS-BCM63XX-move-fallback-sprom-support-into-its-ow.patch new file mode 100644 index 0000000000..450bc1d7d4 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/356-MIPS-BCM63XX-move-fallback-sprom-support-into-its-ow.patch @@ -0,0 +1,188 @@ +From cc025e749a1fece61a6cc0d64bbe7b12472259cc Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 21:31:12 +0200 +Subject: [PATCH 01/10] MIPS: BCM63XX: move fallback sprom support into its own + unit + +In preparation for enhancing it, move it into its own file. Require a +mac address to be passed as the argument to always "reserve" the mac +regardless of the inclusion state of SSB. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/Makefile | 2 +- + arch/mips/bcm63xx/boards/board_common.c | 53 ++-------------- + arch/mips/bcm63xx/sprom.c | 70 ++++++++++++++++++++++ + .../asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 6 ++ + 4 files changed, 83 insertions(+), 48 deletions(-) + create mode 100644 arch/mips/bcm63xx/sprom.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ + dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ +- usb-common.o ++ usb-common.o sprom.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -43,44 +43,6 @@ + static struct board_info board; + + /* +- * Register a sane SPROMv2 to make the on-board +- * bcm4318 WLAN work +- */ +-#ifdef CONFIG_SSB_PCIHOST +-static struct ssb_sprom bcm63xx_sprom = { +- .revision = 0x02, +- .board_rev = 0x17, +- .country_code = 0x0, +- .ant_available_bg = 0x3, +- .pa0b0 = 0x15ae, +- .pa0b1 = 0xfa85, +- .pa0b2 = 0xfe8d, +- .pa1b0 = 0xffff, +- .pa1b1 = 0xffff, +- .pa1b2 = 0xffff, +- .gpio0 = 0xff, +- .gpio1 = 0xff, +- .gpio2 = 0xff, +- .gpio3 = 0xff, +- .maxpwr_bg = 0x004c, +- .itssi_bg = 0x00, +- .boardflags_lo = 0x2848, +- .boardflags_hi = 0x0000, +-}; +- +-int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) +-{ +- if (bus->bustype == SSB_BUSTYPE_PCI) { +- memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); +- return 0; +- } else { +- printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); +- return -EINVAL; +- } +-} +-#endif +- +-/* + * return board name for /proc/cpuinfo + */ + const char *board_get_name(void) +@@ -195,6 +157,7 @@ int __init board_register_devices(void) + int button_count = 0; + int led_count = 0; + int usbh_ports = 0; ++ u8 mac[ETH_ALEN]; + + if (board.has_uart0) + bcm63xx_uart_register(0); +@@ -239,15 +202,10 @@ int __init board_register_devices(void) + /* Generate MAC address for WLAN and register our SPROM, + * do this after registering enet devices + */ +-#ifdef CONFIG_SSB_PCIHOST +- if (!board_get_mac_address(bcm63xx_sprom.il0mac)) { +- memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN); +- memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN); +- if (ssb_arch_register_fallback_sprom( +- &bcm63xx_get_fallback_sprom) < 0) +- pr_err(PFX "failed to register fallback SPROM\n"); +- } +-#endif ++ ++ if (board_get_mac_address(mac) || ++ bcm63xx_register_fallback_sprom(mac)) ++ pr_err(PFX "failed to register fallback SPROM\n"); + + bcm63xx_spi_register(); + +--- /dev/null ++++ b/arch/mips/bcm63xx/sprom.c +@@ -0,0 +1,70 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> ++ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org> ++ */ ++ ++#include <linux/init.h> ++#include <linux/kernel.h> ++#include <linux/string.h> ++#include <linux/platform_device.h> ++#include <linux/ssb/ssb.h> ++#include <bcm63xx_fallback_sprom.h> ++#include <board_bcm963xx.h> ++ ++#define PFX "sprom: " ++ ++/* ++ * Register a sane SPROMv2 to make the on-board ++ * bcm4318 WLAN work ++ */ ++#ifdef CONFIG_SSB_PCIHOST ++static struct ssb_sprom bcm63xx_sprom = { ++ .revision = 0x02, ++ .board_rev = 0x17, ++ .country_code = 0x0, ++ .ant_available_bg = 0x3, ++ .pa0b0 = 0x15ae, ++ .pa0b1 = 0xfa85, ++ .pa0b2 = 0xfe8d, ++ .pa1b0 = 0xffff, ++ .pa1b1 = 0xffff, ++ .pa1b2 = 0xffff, ++ .gpio0 = 0xff, ++ .gpio1 = 0xff, ++ .gpio2 = 0xff, ++ .gpio3 = 0xff, ++ .maxpwr_bg = 0x004c, ++ .itssi_bg = 0x00, ++ .boardflags_lo = 0x2848, ++ .boardflags_hi = 0x0000, ++}; ++ ++int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) ++{ ++ if (bus->bustype == SSB_BUSTYPE_PCI) { ++ memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); ++ return 0; ++ } else { ++ printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); ++ return -EINVAL; ++ } ++} ++#endif ++ ++int __init bcm63xx_register_fallback_sprom(u8 *mac) ++{ ++ int ret = 0; ++ ++#ifdef CONFIG_SSB_PCIHOST ++ memcpy(bcm63xx_sprom.il0mac, mac, ETH_ALEN); ++ memcpy(bcm63xx_sprom.et0mac, mac, ETH_ALEN); ++ memcpy(bcm63xx_sprom.et1mac, mac, ETH_ALEN); ++ ++ ret = ssb_arch_register_fallback_sprom(&bcm63xx_get_fallback_sprom); ++#endif ++ return ret; ++} +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -0,0 +1,6 @@ ++#ifndef __BCM63XX_FALLBACK_SPROM ++#define __BCM63XX_FALLBACK_SPROM ++ ++int bcm63xx_register_fallback_sprom(u8 *mac); ++ ++#endif diff --git a/target/linux/brcm63xx/patches-3.18/357-MIPS-BCM63XX-use-platform-data-for-the-sprom.patch b/target/linux/brcm63xx/patches-3.18/357-MIPS-BCM63XX-use-platform-data-for-the-sprom.patch new file mode 100644 index 0000000000..bc35c25165 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/357-MIPS-BCM63XX-use-platform-data-for-the-sprom.patch @@ -0,0 +1,95 @@ +From 9912a8b3c240a9b0af01ff496b7e8ed9e4cc5b82 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 21:43:49 +0200 +Subject: [PATCH 02/10] MIPS: BCM63XX: use platform data for the sprom + +Similar to ethernet setup, use a platform data struct for passing +the mac. This eliminates the requirement to allocate an array on +stack for the mac passed. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_common.c | 6 ++---- + arch/mips/bcm63xx/sprom.c | 8 ++++---- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 8 +++++++- + arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 4 ++++ + 4 files changed, 17 insertions(+), 9 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -157,7 +157,6 @@ int __init board_register_devices(void) + int button_count = 0; + int led_count = 0; + int usbh_ports = 0; +- u8 mac[ETH_ALEN]; + + if (board.has_uart0) + bcm63xx_uart_register(0); +@@ -203,8 +202,8 @@ int __init board_register_devices(void) + * do this after registering enet devices + */ + +- if (board_get_mac_address(mac) || +- bcm63xx_register_fallback_sprom(mac)) ++ if (board_get_mac_address(board.fallback_sprom.mac_addr) || ++ bcm63xx_register_fallback_sprom(&board.fallback_sprom)) + pr_err(PFX "failed to register fallback SPROM\n"); + + bcm63xx_spi_register(); +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -55,14 +55,14 @@ int bcm63xx_get_fallback_sprom(struct ss + } + #endif + +-int __init bcm63xx_register_fallback_sprom(u8 *mac) ++int __init bcm63xx_register_fallback_sprom(struct fallback_sprom_data *data) + { + int ret = 0; + + #ifdef CONFIG_SSB_PCIHOST +- memcpy(bcm63xx_sprom.il0mac, mac, ETH_ALEN); +- memcpy(bcm63xx_sprom.et0mac, mac, ETH_ALEN); +- memcpy(bcm63xx_sprom.et1mac, mac, ETH_ALEN); ++ memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); ++ memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); ++ memcpy(bcm63xx_sprom.et1mac, data->mac_addr, ETH_ALEN); + + ret = ssb_arch_register_fallback_sprom(&bcm63xx_get_fallback_sprom); + #endif +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -1,6 +1,12 @@ + #ifndef __BCM63XX_FALLBACK_SPROM + #define __BCM63XX_FALLBACK_SPROM + +-int bcm63xx_register_fallback_sprom(u8 *mac); ++#include <linux/if_ether.h> ++ ++struct fallback_sprom_data { ++ u8 mac_addr[ETH_ALEN]; ++}; ++ ++int bcm63xx_register_fallback_sprom(struct fallback_sprom_data *data); + + #endif +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -8,6 +8,7 @@ + #include <bcm63xx_dev_enet.h> + #include <bcm63xx_dev_usb_usbd.h> + #include <bcm63xx_dev_dsp.h> ++#include <bcm63xx_fallback_sprom.h> + + /* + * flash mapping +@@ -59,6 +60,9 @@ struct board_info { + /* External PHY reset GPIO flags from gpio.h */ + unsigned long ephy_reset_gpio_flags; + ++ /* fallback sprom config */ ++ struct fallback_sprom_data fallback_sprom; ++ + /* Additional platform devices */ + struct platform_device **devs; + unsigned int num_devs; diff --git a/target/linux/brcm63xx/patches-3.18/358-MIPS-BCM63XX-make-fallback-sprom-optional.patch b/target/linux/brcm63xx/patches-3.18/358-MIPS-BCM63XX-make-fallback-sprom-optional.patch new file mode 100644 index 0000000000..aedda96895 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/358-MIPS-BCM63XX-make-fallback-sprom-optional.patch @@ -0,0 +1,140 @@ +From 83131acbfb59760a19f3711c09526e191c8aad54 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 21:52:56 +0200 +Subject: [PATCH 03/10] MIPS: BCM63XX: make fallback sprom optional + +Some devices do not provide enough mac addresses to populate wifi in +addition to ethernet. + +Use having pci enabled as a rough heuristic which boards should have it +enabled. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 12 ++++++++++++ + arch/mips/bcm63xx/boards/board_common.c | 5 +++-- + arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 1 + + 3 files changed, 16 insertions(+), 2 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -74,6 +74,7 @@ static struct board_info __initdata boar + .has_uart0 = 1, + .has_pci = 1, + .has_usbd = 0, ++ .use_fallback_sprom = 1, + + .usbd = { + .use_fullspeed = 0, +@@ -223,6 +224,7 @@ static struct board_info __initdata boar + .has_uart0 = 1, + .has_enet0 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -268,6 +270,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -328,6 +331,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -392,6 +396,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -460,6 +465,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -483,6 +489,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -501,6 +508,7 @@ static struct board_info __initdata boar + + .has_uart0 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + .has_ohci0 = 1, + + .has_enet0 = 1, +@@ -523,6 +531,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -549,6 +558,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -601,6 +611,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +@@ -672,6 +683,7 @@ static struct board_info __initdata boar + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, ++ .use_fallback_sprom = 1, + + .enet0 = { + .has_phy = 1, +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -202,8 +202,9 @@ int __init board_register_devices(void) + * do this after registering enet devices + */ + +- if (board_get_mac_address(board.fallback_sprom.mac_addr) || +- bcm63xx_register_fallback_sprom(&board.fallback_sprom)) ++ if (board.use_fallback_sprom && ++ (board_get_mac_address(board.fallback_sprom.mac_addr) || ++ bcm63xx_register_fallback_sprom(&board.fallback_sprom))) + pr_err(PFX "failed to register fallback SPROM\n"); + + bcm63xx_spi_register(); +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -35,6 +35,7 @@ struct board_info { + unsigned int has_dsp:1; + unsigned int has_uart0:1; + unsigned int has_uart1:1; ++ unsigned int use_fallback_sprom:1; + + /* ethernet config */ + struct bcm63xx_enet_platform_data enet0; diff --git a/target/linux/brcm63xx/patches-3.18/359-MIPS-BCM63XX-allow-different-types-of-sprom.patch b/target/linux/brcm63xx/patches-3.18/359-MIPS-BCM63XX-allow-different-types-of-sprom.patch new file mode 100644 index 0000000000..0c4a9be47d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/359-MIPS-BCM63XX-allow-different-types-of-sprom.patch @@ -0,0 +1,66 @@ +From 1cece9f7aca1f0c193edce201f77a87008c5a405 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 21:58:38 +0200 +Subject: [PATCH 04/10] MIPS: BCM63XX: allow different types of sprom + +Different chips require different sprom contents, so prepare for +supplying the appropriate sprom type. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 13 ++++++++++++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 5 +++++ + 2 files changed, 17 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -22,7 +22,7 @@ + * bcm4318 WLAN work + */ + #ifdef CONFIG_SSB_PCIHOST +-static struct ssb_sprom bcm63xx_sprom = { ++static __initconst struct ssb_sprom bcm63xx_default_sprom = { + .revision = 0x02, + .board_rev = 0x17, + .country_code = 0x0, +@@ -43,6 +43,8 @@ static struct ssb_sprom bcm63xx_sprom = + .boardflags_hi = 0x0000, + }; + ++static struct ssb_sprom bcm63xx_sprom; ++ + int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) + { + if (bus->bustype == SSB_BUSTYPE_PCI) { +@@ -60,6 +62,15 @@ int __init bcm63xx_register_fallback_spr + int ret = 0; + + #ifdef CONFIG_SSB_PCIHOST ++ switch (data->type) { ++ case SPROM_DEFAULT: ++ memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, ++ sizeof(bcm63xx_sprom)); ++ break; ++ default: ++ return -EINVAL; ++ } ++ + memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et1mac, data->mac_addr, ETH_ALEN); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -3,8 +3,13 @@ + + #include <linux/if_ether.h> + ++enum sprom_type { ++ SPROM_DEFAULT, /* default fallback sprom */ ++}; ++ + struct fallback_sprom_data { + u8 mac_addr[ETH_ALEN]; ++ enum sprom_type type; + }; + + int bcm63xx_register_fallback_sprom(struct fallback_sprom_data *data); diff --git a/target/linux/brcm63xx/patches-3.18/360-MIPS-BCM63XX-add-support-for-raw-sproms.patch b/target/linux/brcm63xx/patches-3.18/360-MIPS-BCM63XX-add-support-for-raw-sproms.patch new file mode 100644 index 0000000000..42502eb062 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/360-MIPS-BCM63XX-add-support-for-raw-sproms.patch @@ -0,0 +1,517 @@ +From cedee63bc73f8b7d45b8c0cba1236986812c1f83 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 22:16:36 +0200 +Subject: [PATCH 05/10] MIPS: BCM63XX: add support for "raw" sproms + +Allow using raw sprom content as templates. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 482 ++++++++++++++++++++++++++++++++++++++++++++++ + 1 file changed, 482 insertions(+) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -55,13 +55,492 @@ int bcm63xx_get_fallback_sprom(struct ss + return -EINVAL; + } + } ++ ++/* FIXME: use lib_sprom after submission upstream */ ++ ++/* Get the word-offset for a SSB_SPROM_XXX define. */ ++#define SPOFF(offset) ((offset) / sizeof(u16)) ++/* Helper to extract some _offset, which is one of the SSB_SPROM_XXX defines. */ ++#define SPEX16(_outvar, _offset, _mask, _shift) \ ++ out->_outvar = ((in[SPOFF(_offset)] & (_mask)) >> (_shift)) ++#define SPEX32(_outvar, _offset, _mask, _shift) \ ++ out->_outvar = ((((u32)in[SPOFF((_offset)+2)] << 16 | \ ++ in[SPOFF(_offset)]) & (_mask)) >> (_shift)) ++#define SPEX(_outvar, _offset, _mask, _shift) \ ++ SPEX16(_outvar, _offset, _mask, _shift) ++ ++#define SPEX_ARRAY8(_field, _offset, _mask, _shift) \ ++ do { \ ++ SPEX(_field[0], _offset + 0, _mask, _shift); \ ++ SPEX(_field[1], _offset + 2, _mask, _shift); \ ++ SPEX(_field[2], _offset + 4, _mask, _shift); \ ++ SPEX(_field[3], _offset + 6, _mask, _shift); \ ++ SPEX(_field[4], _offset + 8, _mask, _shift); \ ++ SPEX(_field[5], _offset + 10, _mask, _shift); \ ++ SPEX(_field[6], _offset + 12, _mask, _shift); \ ++ SPEX(_field[7], _offset + 14, _mask, _shift); \ ++ } while (0) ++ ++ ++static s8 r123_extract_antgain(u8 sprom_revision, const u16 *in, ++ u16 mask, u16 shift) ++{ ++ u16 v; ++ u8 gain; ++ ++ v = in[SPOFF(SSB_SPROM1_AGAIN)]; ++ gain = (v & mask) >> shift; ++ if (gain == 0xFF) ++ gain = 2; /* If unset use 2dBm */ ++ if (sprom_revision == 1) { ++ /* Convert to Q5.2 */ ++ gain <<= 2; ++ } else { ++ /* Q5.2 Fractional part is stored in 0xC0 */ ++ gain = ((gain & 0xC0) >> 6) | ((gain & 0x3F) << 2); ++ } ++ ++ return (s8)gain; ++} ++ ++static void sprom_extract_r23(struct ssb_sprom *out, const u16 *in) ++{ ++ SPEX(boardflags_hi, SSB_SPROM2_BFLHI, 0xFFFF, 0); ++ SPEX(opo, SSB_SPROM2_OPO, SSB_SPROM2_OPO_VALUE, 0); ++ SPEX(pa1lob0, SSB_SPROM2_PA1LOB0, 0xFFFF, 0); ++ SPEX(pa1lob1, SSB_SPROM2_PA1LOB1, 0xFFFF, 0); ++ SPEX(pa1lob2, SSB_SPROM2_PA1LOB2, 0xFFFF, 0); ++ SPEX(pa1hib0, SSB_SPROM2_PA1HIB0, 0xFFFF, 0); ++ SPEX(pa1hib1, SSB_SPROM2_PA1HIB1, 0xFFFF, 0); ++ SPEX(pa1hib2, SSB_SPROM2_PA1HIB2, 0xFFFF, 0); ++ SPEX(maxpwr_ah, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_HI, 0); ++ SPEX(maxpwr_al, SSB_SPROM2_MAXP_A, SSB_SPROM2_MAXP_A_LO, ++ SSB_SPROM2_MAXP_A_LO_SHIFT); ++} ++ ++static void sprom_extract_r123(struct ssb_sprom *out, const u16 *in) ++{ ++ u16 loc[3]; ++ ++ if (out->revision == 3) /* rev 3 moved MAC */ ++ loc[0] = SSB_SPROM3_IL0MAC; ++ else { ++ loc[0] = SSB_SPROM1_IL0MAC; ++ loc[1] = SSB_SPROM1_ET0MAC; ++ loc[2] = SSB_SPROM1_ET1MAC; ++ } ++ ++ SPEX(et0phyaddr, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET0A, 0); ++ SPEX(et1phyaddr, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET1A, ++ SSB_SPROM1_ETHPHY_ET1A_SHIFT); ++ SPEX(et0mdcport, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET0M, 14); ++ SPEX(et1mdcport, SSB_SPROM1_ETHPHY, SSB_SPROM1_ETHPHY_ET1M, 15); ++ SPEX(board_rev, SSB_SPROM1_BINF, SSB_SPROM1_BINF_BREV, 0); ++ SPEX(board_type, SSB_SPROM1_SPID, 0xFFFF, 0); ++ if (out->revision == 1) ++ SPEX(country_code, SSB_SPROM1_BINF, SSB_SPROM1_BINF_CCODE, ++ SSB_SPROM1_BINF_CCODE_SHIFT); ++ SPEX(ant_available_a, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTA, ++ SSB_SPROM1_BINF_ANTA_SHIFT); ++ SPEX(ant_available_bg, SSB_SPROM1_BINF, SSB_SPROM1_BINF_ANTBG, ++ SSB_SPROM1_BINF_ANTBG_SHIFT); ++ SPEX(pa0b0, SSB_SPROM1_PA0B0, 0xFFFF, 0); ++ SPEX(pa0b1, SSB_SPROM1_PA0B1, 0xFFFF, 0); ++ SPEX(pa0b2, SSB_SPROM1_PA0B2, 0xFFFF, 0); ++ SPEX(pa1b0, SSB_SPROM1_PA1B0, 0xFFFF, 0); ++ SPEX(pa1b1, SSB_SPROM1_PA1B1, 0xFFFF, 0); ++ SPEX(pa1b2, SSB_SPROM1_PA1B2, 0xFFFF, 0); ++ SPEX(gpio0, SSB_SPROM1_GPIOA, SSB_SPROM1_GPIOA_P0, 0); ++ SPEX(gpio1, SSB_SPROM1_GPIOA, SSB_SPROM1_GPIOA_P1, ++ SSB_SPROM1_GPIOA_P1_SHIFT); ++ SPEX(gpio2, SSB_SPROM1_GPIOB, SSB_SPROM1_GPIOB_P2, 0); ++ SPEX(gpio3, SSB_SPROM1_GPIOB, SSB_SPROM1_GPIOB_P3, ++ SSB_SPROM1_GPIOB_P3_SHIFT); ++ SPEX(maxpwr_a, SSB_SPROM1_MAXPWR, SSB_SPROM1_MAXPWR_A, ++ SSB_SPROM1_MAXPWR_A_SHIFT); ++ SPEX(maxpwr_bg, SSB_SPROM1_MAXPWR, SSB_SPROM1_MAXPWR_BG, 0); ++ SPEX(itssi_a, SSB_SPROM1_ITSSI, SSB_SPROM1_ITSSI_A, ++ SSB_SPROM1_ITSSI_A_SHIFT); ++ SPEX(itssi_bg, SSB_SPROM1_ITSSI, SSB_SPROM1_ITSSI_BG, 0); ++ SPEX(boardflags_lo, SSB_SPROM1_BFLLO, 0xFFFF, 0); ++ ++ SPEX(alpha2[0], SSB_SPROM1_CCODE, 0xff00, 8); ++ SPEX(alpha2[1], SSB_SPROM1_CCODE, 0x00ff, 0); ++ ++ /* Extract the antenna gain values. */ ++ out->antenna_gain.a0 = r123_extract_antgain(out->revision, in, ++ SSB_SPROM1_AGAIN_BG, ++ SSB_SPROM1_AGAIN_BG_SHIFT); ++ out->antenna_gain.a1 = r123_extract_antgain(out->revision, in, ++ SSB_SPROM1_AGAIN_A, ++ SSB_SPROM1_AGAIN_A_SHIFT); ++ if (out->revision >= 2) ++ sprom_extract_r23(out, in); ++} ++ ++/* Revs 4 5 and 8 have partially shared layout */ ++static void sprom_extract_r458(struct ssb_sprom *out, const u16 *in) ++{ ++ SPEX(txpid2g[0], SSB_SPROM4_TXPID2G01, ++ SSB_SPROM4_TXPID2G0, SSB_SPROM4_TXPID2G0_SHIFT); ++ SPEX(txpid2g[1], SSB_SPROM4_TXPID2G01, ++ SSB_SPROM4_TXPID2G1, SSB_SPROM4_TXPID2G1_SHIFT); ++ SPEX(txpid2g[2], SSB_SPROM4_TXPID2G23, ++ SSB_SPROM4_TXPID2G2, SSB_SPROM4_TXPID2G2_SHIFT); ++ SPEX(txpid2g[3], SSB_SPROM4_TXPID2G23, ++ SSB_SPROM4_TXPID2G3, SSB_SPROM4_TXPID2G3_SHIFT); ++ ++ SPEX(txpid5gl[0], SSB_SPROM4_TXPID5GL01, ++ SSB_SPROM4_TXPID5GL0, SSB_SPROM4_TXPID5GL0_SHIFT); ++ SPEX(txpid5gl[1], SSB_SPROM4_TXPID5GL01, ++ SSB_SPROM4_TXPID5GL1, SSB_SPROM4_TXPID5GL1_SHIFT); ++ SPEX(txpid5gl[2], SSB_SPROM4_TXPID5GL23, ++ SSB_SPROM4_TXPID5GL2, SSB_SPROM4_TXPID5GL2_SHIFT); ++ SPEX(txpid5gl[3], SSB_SPROM4_TXPID5GL23, ++ SSB_SPROM4_TXPID5GL3, SSB_SPROM4_TXPID5GL3_SHIFT); ++ ++ SPEX(txpid5g[0], SSB_SPROM4_TXPID5G01, ++ SSB_SPROM4_TXPID5G0, SSB_SPROM4_TXPID5G0_SHIFT); ++ SPEX(txpid5g[1], SSB_SPROM4_TXPID5G01, ++ SSB_SPROM4_TXPID5G1, SSB_SPROM4_TXPID5G1_SHIFT); ++ SPEX(txpid5g[2], SSB_SPROM4_TXPID5G23, ++ SSB_SPROM4_TXPID5G2, SSB_SPROM4_TXPID5G2_SHIFT); ++ SPEX(txpid5g[3], SSB_SPROM4_TXPID5G23, ++ SSB_SPROM4_TXPID5G3, SSB_SPROM4_TXPID5G3_SHIFT); ++ ++ SPEX(txpid5gh[0], SSB_SPROM4_TXPID5GH01, ++ SSB_SPROM4_TXPID5GH0, SSB_SPROM4_TXPID5GH0_SHIFT); ++ SPEX(txpid5gh[1], SSB_SPROM4_TXPID5GH01, ++ SSB_SPROM4_TXPID5GH1, SSB_SPROM4_TXPID5GH1_SHIFT); ++ SPEX(txpid5gh[2], SSB_SPROM4_TXPID5GH23, ++ SSB_SPROM4_TXPID5GH2, SSB_SPROM4_TXPID5GH2_SHIFT); ++ SPEX(txpid5gh[3], SSB_SPROM4_TXPID5GH23, ++ SSB_SPROM4_TXPID5GH3, SSB_SPROM4_TXPID5GH3_SHIFT); ++} ++ ++static void sprom_extract_r45(struct ssb_sprom *out, const u16 *in) ++{ ++ u16 il0mac_offset; ++ ++ if (out->revision == 4) ++ il0mac_offset = SSB_SPROM4_IL0MAC; ++ else ++ il0mac_offset = SSB_SPROM5_IL0MAC; ++ ++ SPEX(et0phyaddr, SSB_SPROM4_ETHPHY, SSB_SPROM4_ETHPHY_ET0A, 0); ++ SPEX(et1phyaddr, SSB_SPROM4_ETHPHY, SSB_SPROM4_ETHPHY_ET1A, ++ SSB_SPROM4_ETHPHY_ET1A_SHIFT); ++ SPEX(board_rev, SSB_SPROM4_BOARDREV, 0xFFFF, 0); ++ SPEX(board_type, SSB_SPROM1_SPID, 0xFFFF, 0); ++ if (out->revision == 4) { ++ SPEX(alpha2[0], SSB_SPROM4_CCODE, 0xff00, 8); ++ SPEX(alpha2[1], SSB_SPROM4_CCODE, 0x00ff, 0); ++ SPEX(boardflags_lo, SSB_SPROM4_BFLLO, 0xFFFF, 0); ++ SPEX(boardflags_hi, SSB_SPROM4_BFLHI, 0xFFFF, 0); ++ SPEX(boardflags2_lo, SSB_SPROM4_BFL2LO, 0xFFFF, 0); ++ SPEX(boardflags2_hi, SSB_SPROM4_BFL2HI, 0xFFFF, 0); ++ } else { ++ SPEX(alpha2[0], SSB_SPROM5_CCODE, 0xff00, 8); ++ SPEX(alpha2[1], SSB_SPROM5_CCODE, 0x00ff, 0); ++ SPEX(boardflags_lo, SSB_SPROM5_BFLLO, 0xFFFF, 0); ++ SPEX(boardflags_hi, SSB_SPROM5_BFLHI, 0xFFFF, 0); ++ SPEX(boardflags2_lo, SSB_SPROM5_BFL2LO, 0xFFFF, 0); ++ SPEX(boardflags2_hi, SSB_SPROM5_BFL2HI, 0xFFFF, 0); ++ } ++ SPEX(ant_available_a, SSB_SPROM4_ANTAVAIL, SSB_SPROM4_ANTAVAIL_A, ++ SSB_SPROM4_ANTAVAIL_A_SHIFT); ++ SPEX(ant_available_bg, SSB_SPROM4_ANTAVAIL, SSB_SPROM4_ANTAVAIL_BG, ++ SSB_SPROM4_ANTAVAIL_BG_SHIFT); ++ SPEX(maxpwr_bg, SSB_SPROM4_MAXP_BG, SSB_SPROM4_MAXP_BG_MASK, 0); ++ SPEX(itssi_bg, SSB_SPROM4_MAXP_BG, SSB_SPROM4_ITSSI_BG, ++ SSB_SPROM4_ITSSI_BG_SHIFT); ++ SPEX(maxpwr_a, SSB_SPROM4_MAXP_A, SSB_SPROM4_MAXP_A_MASK, 0); ++ SPEX(itssi_a, SSB_SPROM4_MAXP_A, SSB_SPROM4_ITSSI_A, ++ SSB_SPROM4_ITSSI_A_SHIFT); ++ if (out->revision == 4) { ++ SPEX(gpio0, SSB_SPROM4_GPIOA, SSB_SPROM4_GPIOA_P0, 0); ++ SPEX(gpio1, SSB_SPROM4_GPIOA, SSB_SPROM4_GPIOA_P1, ++ SSB_SPROM4_GPIOA_P1_SHIFT); ++ SPEX(gpio2, SSB_SPROM4_GPIOB, SSB_SPROM4_GPIOB_P2, 0); ++ SPEX(gpio3, SSB_SPROM4_GPIOB, SSB_SPROM4_GPIOB_P3, ++ SSB_SPROM4_GPIOB_P3_SHIFT); ++ } else { ++ SPEX(gpio0, SSB_SPROM5_GPIOA, SSB_SPROM5_GPIOA_P0, 0); ++ SPEX(gpio1, SSB_SPROM5_GPIOA, SSB_SPROM5_GPIOA_P1, ++ SSB_SPROM5_GPIOA_P1_SHIFT); ++ SPEX(gpio2, SSB_SPROM5_GPIOB, SSB_SPROM5_GPIOB_P2, 0); ++ SPEX(gpio3, SSB_SPROM5_GPIOB, SSB_SPROM5_GPIOB_P3, ++ SSB_SPROM5_GPIOB_P3_SHIFT); ++ } ++ ++ /* Extract the antenna gain values. */ ++ SPEX(antenna_gain.a0, SSB_SPROM4_AGAIN01, ++ SSB_SPROM4_AGAIN0, SSB_SPROM4_AGAIN0_SHIFT); ++ SPEX(antenna_gain.a1, SSB_SPROM4_AGAIN01, ++ SSB_SPROM4_AGAIN1, SSB_SPROM4_AGAIN1_SHIFT); ++ SPEX(antenna_gain.a2, SSB_SPROM4_AGAIN23, ++ SSB_SPROM4_AGAIN2, SSB_SPROM4_AGAIN2_SHIFT); ++ SPEX(antenna_gain.a3, SSB_SPROM4_AGAIN23, ++ SSB_SPROM4_AGAIN3, SSB_SPROM4_AGAIN3_SHIFT); ++ ++ sprom_extract_r458(out, in); ++ ++ /* TODO - get remaining rev 4 stuff needed */ ++} ++ ++static void sprom_extract_r8(struct ssb_sprom *out, const u16 *in) ++{ ++ int i; ++ u16 o; ++ u16 pwr_info_offset[] = { ++ SSB_SROM8_PWR_INFO_CORE0, SSB_SROM8_PWR_INFO_CORE1, ++ SSB_SROM8_PWR_INFO_CORE2, SSB_SROM8_PWR_INFO_CORE3 ++ }; ++ BUILD_BUG_ON(ARRAY_SIZE(pwr_info_offset) != ++ ARRAY_SIZE(out->core_pwr_info)); ++ ++ SPEX(board_rev, SSB_SPROM8_BOARDREV, 0xFFFF, 0); ++ SPEX(board_type, SSB_SPROM1_SPID, 0xFFFF, 0); ++ SPEX(alpha2[0], SSB_SPROM8_CCODE, 0xff00, 8); ++ SPEX(alpha2[1], SSB_SPROM8_CCODE, 0x00ff, 0); ++ SPEX(boardflags_lo, SSB_SPROM8_BFLLO, 0xFFFF, 0); ++ SPEX(boardflags_hi, SSB_SPROM8_BFLHI, 0xFFFF, 0); ++ SPEX(boardflags2_lo, SSB_SPROM8_BFL2LO, 0xFFFF, 0); ++ SPEX(boardflags2_hi, SSB_SPROM8_BFL2HI, 0xFFFF, 0); ++ SPEX(ant_available_a, SSB_SPROM8_ANTAVAIL, SSB_SPROM8_ANTAVAIL_A, ++ SSB_SPROM8_ANTAVAIL_A_SHIFT); ++ SPEX(ant_available_bg, SSB_SPROM8_ANTAVAIL, SSB_SPROM8_ANTAVAIL_BG, ++ SSB_SPROM8_ANTAVAIL_BG_SHIFT); ++ SPEX(maxpwr_bg, SSB_SPROM8_MAXP_BG, SSB_SPROM8_MAXP_BG_MASK, 0); ++ SPEX(itssi_bg, SSB_SPROM8_MAXP_BG, SSB_SPROM8_ITSSI_BG, ++ SSB_SPROM8_ITSSI_BG_SHIFT); ++ SPEX(maxpwr_a, SSB_SPROM8_MAXP_A, SSB_SPROM8_MAXP_A_MASK, 0); ++ SPEX(itssi_a, SSB_SPROM8_MAXP_A, SSB_SPROM8_ITSSI_A, ++ SSB_SPROM8_ITSSI_A_SHIFT); ++ SPEX(maxpwr_ah, SSB_SPROM8_MAXP_AHL, SSB_SPROM8_MAXP_AH_MASK, 0); ++ SPEX(maxpwr_al, SSB_SPROM8_MAXP_AHL, SSB_SPROM8_MAXP_AL_MASK, ++ SSB_SPROM8_MAXP_AL_SHIFT); ++ SPEX(gpio0, SSB_SPROM8_GPIOA, SSB_SPROM8_GPIOA_P0, 0); ++ SPEX(gpio1, SSB_SPROM8_GPIOA, SSB_SPROM8_GPIOA_P1, ++ SSB_SPROM8_GPIOA_P1_SHIFT); ++ SPEX(gpio2, SSB_SPROM8_GPIOB, SSB_SPROM8_GPIOB_P2, 0); ++ SPEX(gpio3, SSB_SPROM8_GPIOB, SSB_SPROM8_GPIOB_P3, ++ SSB_SPROM8_GPIOB_P3_SHIFT); ++ SPEX(tri2g, SSB_SPROM8_TRI25G, SSB_SPROM8_TRI2G, 0); ++ SPEX(tri5g, SSB_SPROM8_TRI25G, SSB_SPROM8_TRI5G, ++ SSB_SPROM8_TRI5G_SHIFT); ++ SPEX(tri5gl, SSB_SPROM8_TRI5GHL, SSB_SPROM8_TRI5GL, 0); ++ SPEX(tri5gh, SSB_SPROM8_TRI5GHL, SSB_SPROM8_TRI5GH, ++ SSB_SPROM8_TRI5GH_SHIFT); ++ SPEX(rxpo2g, SSB_SPROM8_RXPO, SSB_SPROM8_RXPO2G, 0); ++ SPEX(rxpo5g, SSB_SPROM8_RXPO, SSB_SPROM8_RXPO5G, ++ SSB_SPROM8_RXPO5G_SHIFT); ++ SPEX(rssismf2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISMF2G, 0); ++ SPEX(rssismc2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISMC2G, ++ SSB_SPROM8_RSSISMC2G_SHIFT); ++ SPEX(rssisav2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_RSSISAV2G, ++ SSB_SPROM8_RSSISAV2G_SHIFT); ++ SPEX(bxa2g, SSB_SPROM8_RSSIPARM2G, SSB_SPROM8_BXA2G, ++ SSB_SPROM8_BXA2G_SHIFT); ++ SPEX(rssismf5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISMF5G, 0); ++ SPEX(rssismc5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISMC5G, ++ SSB_SPROM8_RSSISMC5G_SHIFT); ++ SPEX(rssisav5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_RSSISAV5G, ++ SSB_SPROM8_RSSISAV5G_SHIFT); ++ SPEX(bxa5g, SSB_SPROM8_RSSIPARM5G, SSB_SPROM8_BXA5G, ++ SSB_SPROM8_BXA5G_SHIFT); ++ SPEX(pa0b0, SSB_SPROM8_PA0B0, 0xFFFF, 0); ++ SPEX(pa0b1, SSB_SPROM8_PA0B1, 0xFFFF, 0); ++ SPEX(pa0b2, SSB_SPROM8_PA0B2, 0xFFFF, 0); ++ SPEX(pa1b0, SSB_SPROM8_PA1B0, 0xFFFF, 0); ++ SPEX(pa1b1, SSB_SPROM8_PA1B1, 0xFFFF, 0); ++ SPEX(pa1b2, SSB_SPROM8_PA1B2, 0xFFFF, 0); ++ SPEX(pa1lob0, SSB_SPROM8_PA1LOB0, 0xFFFF, 0); ++ SPEX(pa1lob1, SSB_SPROM8_PA1LOB1, 0xFFFF, 0); ++ SPEX(pa1lob2, SSB_SPROM8_PA1LOB2, 0xFFFF, 0); ++ SPEX(pa1hib0, SSB_SPROM8_PA1HIB0, 0xFFFF, 0); ++ SPEX(pa1hib1, SSB_SPROM8_PA1HIB1, 0xFFFF, 0); ++ SPEX(pa1hib2, SSB_SPROM8_PA1HIB2, 0xFFFF, 0); ++ SPEX(cck2gpo, SSB_SPROM8_CCK2GPO, 0xFFFF, 0); ++ SPEX32(ofdm2gpo, SSB_SPROM8_OFDM2GPO, 0xFFFFFFFF, 0); ++ SPEX32(ofdm5glpo, SSB_SPROM8_OFDM5GLPO, 0xFFFFFFFF, 0); ++ SPEX32(ofdm5gpo, SSB_SPROM8_OFDM5GPO, 0xFFFFFFFF, 0); ++ SPEX32(ofdm5ghpo, SSB_SPROM8_OFDM5GHPO, 0xFFFFFFFF, 0); ++ ++ /* Extract the antenna gain values. */ ++ SPEX(antenna_gain.a0, SSB_SPROM8_AGAIN01, ++ SSB_SPROM8_AGAIN0, SSB_SPROM8_AGAIN0_SHIFT); ++ SPEX(antenna_gain.a1, SSB_SPROM8_AGAIN01, ++ SSB_SPROM8_AGAIN1, SSB_SPROM8_AGAIN1_SHIFT); ++ SPEX(antenna_gain.a2, SSB_SPROM8_AGAIN23, ++ SSB_SPROM8_AGAIN2, SSB_SPROM8_AGAIN2_SHIFT); ++ SPEX(antenna_gain.a3, SSB_SPROM8_AGAIN23, ++ SSB_SPROM8_AGAIN3, SSB_SPROM8_AGAIN3_SHIFT); ++ ++ /* Extract cores power info info */ ++ for (i = 0; i < ARRAY_SIZE(pwr_info_offset); i++) { ++ o = pwr_info_offset[i]; ++ SPEX(core_pwr_info[i].itssi_2g, o + SSB_SROM8_2G_MAXP_ITSSI, ++ SSB_SPROM8_2G_ITSSI, SSB_SPROM8_2G_ITSSI_SHIFT); ++ SPEX(core_pwr_info[i].maxpwr_2g, o + SSB_SROM8_2G_MAXP_ITSSI, ++ SSB_SPROM8_2G_MAXP, 0); ++ ++ SPEX(core_pwr_info[i].pa_2g[0], o + SSB_SROM8_2G_PA_0, ~0, 0); ++ SPEX(core_pwr_info[i].pa_2g[1], o + SSB_SROM8_2G_PA_1, ~0, 0); ++ SPEX(core_pwr_info[i].pa_2g[2], o + SSB_SROM8_2G_PA_2, ~0, 0); ++ ++ SPEX(core_pwr_info[i].itssi_5g, o + SSB_SROM8_5G_MAXP_ITSSI, ++ SSB_SPROM8_5G_ITSSI, SSB_SPROM8_5G_ITSSI_SHIFT); ++ SPEX(core_pwr_info[i].maxpwr_5g, o + SSB_SROM8_5G_MAXP_ITSSI, ++ SSB_SPROM8_5G_MAXP, 0); ++ SPEX(core_pwr_info[i].maxpwr_5gh, o + SSB_SPROM8_5GHL_MAXP, ++ SSB_SPROM8_5GH_MAXP, 0); ++ SPEX(core_pwr_info[i].maxpwr_5gl, o + SSB_SPROM8_5GHL_MAXP, ++ SSB_SPROM8_5GL_MAXP, SSB_SPROM8_5GL_MAXP_SHIFT); ++ ++ SPEX(core_pwr_info[i].pa_5gl[0], o + SSB_SROM8_5GL_PA_0, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5gl[1], o + SSB_SROM8_5GL_PA_1, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5gl[2], o + SSB_SROM8_5GL_PA_2, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5g[0], o + SSB_SROM8_5G_PA_0, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5g[1], o + SSB_SROM8_5G_PA_1, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5g[2], o + SSB_SROM8_5G_PA_2, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5gh[0], o + SSB_SROM8_5GH_PA_0, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5gh[1], o + SSB_SROM8_5GH_PA_1, ~0, 0); ++ SPEX(core_pwr_info[i].pa_5gh[2], o + SSB_SROM8_5GH_PA_2, ~0, 0); ++ } ++ ++ /* Extract FEM info */ ++ SPEX(fem.ghz2.tssipos, SSB_SPROM8_FEM2G, ++ SSB_SROM8_FEM_TSSIPOS, SSB_SROM8_FEM_TSSIPOS_SHIFT); ++ SPEX(fem.ghz2.extpa_gain, SSB_SPROM8_FEM2G, ++ SSB_SROM8_FEM_EXTPA_GAIN, SSB_SROM8_FEM_EXTPA_GAIN_SHIFT); ++ SPEX(fem.ghz2.pdet_range, SSB_SPROM8_FEM2G, ++ SSB_SROM8_FEM_PDET_RANGE, SSB_SROM8_FEM_PDET_RANGE_SHIFT); ++ SPEX(fem.ghz2.tr_iso, SSB_SPROM8_FEM2G, ++ SSB_SROM8_FEM_TR_ISO, SSB_SROM8_FEM_TR_ISO_SHIFT); ++ SPEX(fem.ghz2.antswlut, SSB_SPROM8_FEM2G, ++ SSB_SROM8_FEM_ANTSWLUT, SSB_SROM8_FEM_ANTSWLUT_SHIFT); ++ ++ SPEX(fem.ghz5.tssipos, SSB_SPROM8_FEM5G, ++ SSB_SROM8_FEM_TSSIPOS, SSB_SROM8_FEM_TSSIPOS_SHIFT); ++ SPEX(fem.ghz5.extpa_gain, SSB_SPROM8_FEM5G, ++ SSB_SROM8_FEM_EXTPA_GAIN, SSB_SROM8_FEM_EXTPA_GAIN_SHIFT); ++ SPEX(fem.ghz5.pdet_range, SSB_SPROM8_FEM5G, ++ SSB_SROM8_FEM_PDET_RANGE, SSB_SROM8_FEM_PDET_RANGE_SHIFT); ++ SPEX(fem.ghz5.tr_iso, SSB_SPROM8_FEM5G, ++ SSB_SROM8_FEM_TR_ISO, SSB_SROM8_FEM_TR_ISO_SHIFT); ++ SPEX(fem.ghz5.antswlut, SSB_SPROM8_FEM5G, ++ SSB_SROM8_FEM_ANTSWLUT, SSB_SROM8_FEM_ANTSWLUT_SHIFT); ++ ++ SPEX(leddc_on_time, SSB_SPROM8_LEDDC, SSB_SPROM8_LEDDC_ON, ++ SSB_SPROM8_LEDDC_ON_SHIFT); ++ SPEX(leddc_off_time, SSB_SPROM8_LEDDC, SSB_SPROM8_LEDDC_OFF, ++ SSB_SPROM8_LEDDC_OFF_SHIFT); ++ ++ SPEX(txchain, SSB_SPROM8_TXRXC, SSB_SPROM8_TXRXC_TXCHAIN, ++ SSB_SPROM8_TXRXC_TXCHAIN_SHIFT); ++ SPEX(rxchain, SSB_SPROM8_TXRXC, SSB_SPROM8_TXRXC_RXCHAIN, ++ SSB_SPROM8_TXRXC_RXCHAIN_SHIFT); ++ SPEX(antswitch, SSB_SPROM8_TXRXC, SSB_SPROM8_TXRXC_SWITCH, ++ SSB_SPROM8_TXRXC_SWITCH_SHIFT); ++ ++ SPEX(opo, SSB_SPROM8_OFDM2GPO, 0x00ff, 0); ++ ++ SPEX_ARRAY8(mcs2gpo, SSB_SPROM8_2G_MCSPO, ~0, 0); ++ SPEX_ARRAY8(mcs5gpo, SSB_SPROM8_5G_MCSPO, ~0, 0); ++ SPEX_ARRAY8(mcs5glpo, SSB_SPROM8_5GL_MCSPO, ~0, 0); ++ SPEX_ARRAY8(mcs5ghpo, SSB_SPROM8_5GH_MCSPO, ~0, 0); ++ ++ SPEX(rawtempsense, SSB_SPROM8_RAWTS, SSB_SPROM8_RAWTS_RAWTEMP, ++ SSB_SPROM8_RAWTS_RAWTEMP_SHIFT); ++ SPEX(measpower, SSB_SPROM8_RAWTS, SSB_SPROM8_RAWTS_MEASPOWER, ++ SSB_SPROM8_RAWTS_MEASPOWER_SHIFT); ++ SPEX(tempsense_slope, SSB_SPROM8_OPT_CORRX, ++ SSB_SPROM8_OPT_CORRX_TEMP_SLOPE, ++ SSB_SPROM8_OPT_CORRX_TEMP_SLOPE_SHIFT); ++ SPEX(tempcorrx, SSB_SPROM8_OPT_CORRX, SSB_SPROM8_OPT_CORRX_TEMPCORRX, ++ SSB_SPROM8_OPT_CORRX_TEMPCORRX_SHIFT); ++ SPEX(tempsense_option, SSB_SPROM8_OPT_CORRX, ++ SSB_SPROM8_OPT_CORRX_TEMP_OPTION, ++ SSB_SPROM8_OPT_CORRX_TEMP_OPTION_SHIFT); ++ SPEX(freqoffset_corr, SSB_SPROM8_HWIQ_IQSWP, ++ SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR, ++ SSB_SPROM8_HWIQ_IQSWP_FREQ_CORR_SHIFT); ++ SPEX(iqcal_swp_dis, SSB_SPROM8_HWIQ_IQSWP, ++ SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP, ++ SSB_SPROM8_HWIQ_IQSWP_IQCAL_SWP_SHIFT); ++ SPEX(hw_iqcal_en, SSB_SPROM8_HWIQ_IQSWP, SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL, ++ SSB_SPROM8_HWIQ_IQSWP_HW_IQCAL_SHIFT); ++ ++ SPEX(bw40po, SSB_SPROM8_BW40PO, ~0, 0); ++ SPEX(cddpo, SSB_SPROM8_CDDPO, ~0, 0); ++ SPEX(stbcpo, SSB_SPROM8_STBCPO, ~0, 0); ++ SPEX(bwduppo, SSB_SPROM8_BWDUPPO, ~0, 0); ++ ++ SPEX(tempthresh, SSB_SPROM8_THERMAL, SSB_SPROM8_THERMAL_TRESH, ++ SSB_SPROM8_THERMAL_TRESH_SHIFT); ++ SPEX(tempoffset, SSB_SPROM8_THERMAL, SSB_SPROM8_THERMAL_OFFSET, ++ SSB_SPROM8_THERMAL_OFFSET_SHIFT); ++ SPEX(phycal_tempdelta, SSB_SPROM8_TEMPDELTA, ++ SSB_SPROM8_TEMPDELTA_PHYCAL, ++ SSB_SPROM8_TEMPDELTA_PHYCAL_SHIFT); ++ SPEX(temps_period, SSB_SPROM8_TEMPDELTA, SSB_SPROM8_TEMPDELTA_PERIOD, ++ SSB_SPROM8_TEMPDELTA_PERIOD_SHIFT); ++ SPEX(temps_hysteresis, SSB_SPROM8_TEMPDELTA, ++ SSB_SPROM8_TEMPDELTA_HYSTERESIS, ++ SSB_SPROM8_TEMPDELTA_HYSTERESIS_SHIFT); ++ sprom_extract_r458(out, in); ++ ++ /* TODO - get remaining rev 8 stuff needed */ ++} ++ ++static int sprom_extract(struct ssb_sprom *out, const u16 *in, u16 size) ++{ ++ memset(out, 0, sizeof(*out)); ++ ++ out->revision = in[size - 1] & 0x00FF; ++ memset(out->et0mac, 0xFF, 6); /* preset et0 and et1 mac */ ++ memset(out->et1mac, 0xFF, 6); ++ ++ switch (out->revision) { ++ case 1: ++ case 2: ++ case 3: ++ sprom_extract_r123(out, in); ++ break; ++ case 4: ++ case 5: ++ sprom_extract_r45(out, in); ++ break; ++ case 8: ++ sprom_extract_r8(out, in); ++ break; ++ default: ++ pr_warn("Unsupported SPROM revision %d detected. Will extract v1\n", ++ out->revision); ++ out->revision = 1; ++ sprom_extract_r123(out, in); ++ } ++ ++ if (out->boardflags_lo == 0xFFFF) ++ out->boardflags_lo = 0; /* per specs */ ++ if (out->boardflags_hi == 0xFFFF) ++ out->boardflags_hi = 0; /* per specs */ ++ ++ return 0; ++} ++ ++static __initdata u16 template_sprom[220]; + #endif + ++ + int __init bcm63xx_register_fallback_sprom(struct fallback_sprom_data *data) + { + int ret = 0; + + #ifdef CONFIG_SSB_PCIHOST ++ u16 size = 0; ++ + switch (data->type) { + case SPROM_DEFAULT: + memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, +@@ -71,6 +550,9 @@ int __init bcm63xx_register_fallback_spr + return -EINVAL; + } + ++ if (size > 0) ++ sprom_extract(&bcm63xx_sprom, template_sprom, size); ++ + memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et1mac, data->mac_addr, ETH_ALEN); diff --git a/target/linux/brcm63xx/patches-3.18/361-MIPS-BCM63XX-add-raw-fallback-sproms-for-most-common.patch b/target/linux/brcm63xx/patches-3.18/361-MIPS-BCM63XX-add-raw-fallback-sproms-for-most-common.patch new file mode 100644 index 0000000000..65c00b5197 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/361-MIPS-BCM63XX-add-raw-fallback-sproms-for-most-common.patch @@ -0,0 +1,181 @@ +From 7be5bb46003295c9e04fd4e795593b2deaacd783 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 22:33:38 +0200 +Subject: [PATCH 06/10] MIPS: BCM63XX: add raw fallback sproms for most common + ssb cards + +Add template sproms for BCM4306, BCM4318, BCM4321, BCM4322, and BCM43222. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 136 +++++++++++++++++++++ + .../asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 6 + + 2 files changed, 142 insertions(+) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -43,6 +43,122 @@ static __initconst struct ssb_sprom bcm6 + .boardflags_hi = 0x0000, + }; + ++ ++static __initconst u16 bcm4306_sprom[] = { ++ 0x4001, 0x0000, 0x0453, 0x14e4, 0x4320, 0x8000, 0x0002, 0x0002, ++ 0x1000, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x3034, 0x14d4, ++ 0xfa91, 0xfe60, 0xffff, 0xffff, 0x004c, 0xffff, 0xffff, 0xffff, ++ 0x003e, 0x0a49, 0xff02, 0x0000, 0xff10, 0xffff, 0xffff, 0x0002, ++}; ++ ++static __initconst u16 bcm4318_sprom[] = { ++ 0x2001, 0x0000, 0x0449, 0x14e4, 0x4318, 0x8000, 0x0002, 0x0000, ++ 0x1000, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0x0000, 0x0000, 0x0000, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x3046, 0x15a7, ++ 0xfab0, 0xfe97, 0xffff, 0xffff, 0x0048, 0xffff, 0xffff, 0xffff, ++ 0x003e, 0xea49, 0xff02, 0x0000, 0xff08, 0xffff, 0xffff, 0x0002, ++}; ++ ++static __initconst u16 bcm4321_sprom[] = { ++ 0x3001, 0x0000, 0x046c, 0x14e4, 0x4328, 0x8000, 0x0002, 0x0000, ++ 0x1000, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x5372, 0x0032, 0x4a01, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0x0303, 0x0202, ++ 0xffff, 0x2728, 0x5b5b, 0x222b, 0x5b5b, 0x1927, 0x5b5b, 0x1e36, ++ 0x5b5b, 0x303c, 0x3030, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x3e4c, 0x0000, 0x0000, 0x0000, 0x0000, 0x7838, 0x3a34, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0x3e4c, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x7838, 0x3a34, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0x0008, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0004, ++}; ++ ++static __initconst u16 bcm4322_sprom[] = { ++ 0x3001, 0x0000, 0x04bc, 0x14e4, 0x432c, 0x8000, 0x0002, 0x0000, ++ 0x1730, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x5372, 0x1209, 0x0200, 0x0000, 0x0400, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0x0303, 0x0202, ++ 0xffff, 0x0033, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x0301, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x2048, 0xfe9a, 0x1571, 0xfabd, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x2048, 0xfeb9, 0x159f, 0xfadd, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x3333, 0x5555, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0008, ++}; ++ ++static __initconst u16 bcm43222_sprom[] = { ++ 0x2001, 0x0000, 0x04d4, 0x14e4, 0x4351, 0x8000, 0x0002, 0x0000, ++ 0x1730, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x5372, 0x2305, 0x0200, 0x0000, 0x2400, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0x0303, 0x0202, ++ 0xffff, 0x0033, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x0325, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x204c, 0xfea6, 0x1717, 0xfa6d, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x204c, 0xfeb8, 0x167c, 0xfa9e, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x3333, 0x3333, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x3333, 0x3333, 0x3333, 0x3333, 0x3333, 0x3333, 0x3333, ++ 0x3333, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0004, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0008, ++}; ++ + static struct ssb_sprom bcm63xx_sprom; + + int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) +@@ -542,6 +658,26 @@ int __init bcm63xx_register_fallback_spr + u16 size = 0; + + switch (data->type) { ++ case SPROM_BCM4306: ++ memcpy(&template_sprom, &bcm4306_sprom, sizeof(bcm4306_sprom)); ++ size = ARRAY_SIZE(bcm4306_sprom); ++ break; ++ case SPROM_BCM4318: ++ memcpy(&template_sprom, &bcm4318_sprom, sizeof(bcm4318_sprom)); ++ size = ARRAY_SIZE(bcm4318_sprom); ++ break; ++ case SPROM_BCM4321: ++ memcpy(&template_sprom, &bcm4321_sprom, sizeof(bcm4321_sprom)); ++ size = ARRAY_SIZE(bcm4321_sprom); ++ break; ++ case SPROM_BCM4322: ++ memcpy(&template_sprom, &bcm4322_sprom, sizeof(bcm4322_sprom)); ++ size = ARRAY_SIZE(bcm4322_sprom); ++ break; ++ case SPROM_BCM43222: ++ memcpy(&template_sprom, &bcm43222_sprom, sizeof(bcm43222_sprom)); ++ size = ARRAY_SIZE(bcm43222_sprom); ++ break; + case SPROM_DEFAULT: + memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, + sizeof(bcm63xx_sprom)); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -5,6 +5,12 @@ + + enum sprom_type { + SPROM_DEFAULT, /* default fallback sprom */ ++ /* SSB based */ ++ SPROM_BCM4306, ++ SPROM_BCM4318, ++ SPROM_BCM4321, ++ SPROM_BCM4322, ++ SPROM_BCM43222, + }; + + struct fallback_sprom_data { diff --git a/target/linux/brcm63xx/patches-3.18/362-MIPS-BCM63XX-also-register-a-fallback-sprom-for-bcma.patch b/target/linux/brcm63xx/patches-3.18/362-MIPS-BCM63XX-also-register-a-fallback-sprom-for-bcma.patch new file mode 100644 index 0000000000..6475f9fa24 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/362-MIPS-BCM63XX-also-register-a-fallback-sprom-for-bcma.patch @@ -0,0 +1,128 @@ +From 03feb9db77fba3eef3d83e17a87a56979659b248 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 29 Jul 2014 22:48:26 +0200 +Subject: [PATCH 07/10] MIPS: BCM63XX: also register a fallback sprom for bcma + +Similar to SSB, register a fallback sprom handler for BCMA. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/Kconfig | 1 + + arch/mips/bcm63xx/sprom.c | 40 +++++++++++++++++++++++++++++++++++----- + 2 files changed, 36 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/boards/Kconfig ++++ b/arch/mips/bcm63xx/boards/Kconfig +@@ -4,6 +4,7 @@ menu "Board support" + config BOARD_BCM963XX + bool "Generic Broadcom 963xx boards" + select SSB ++ select BCMA + default y + help + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -12,6 +12,7 @@ + #include <linux/string.h> + #include <linux/platform_device.h> + #include <linux/ssb/ssb.h> ++#include <linux/bcma/bcma.h> + #include <bcm63xx_fallback_sprom.h> + #include <board_bcm963xx.h> + +@@ -21,7 +22,7 @@ + * Register a sane SPROMv2 to make the on-board + * bcm4318 WLAN work + */ +-#ifdef CONFIG_SSB_PCIHOST ++#if defined(CONFIG_SSB_PCIHOST) || defined(CONFIG_BCMA_HOST_PCI) + static __initconst struct ssb_sprom bcm63xx_default_sprom = { + .revision = 0x02, + .board_rev = 0x17, +@@ -43,7 +44,7 @@ static __initconst struct ssb_sprom bcm6 + .boardflags_hi = 0x0000, + }; + +- ++#if defined (CONFIG_SSB_PCIHOST) + static __initconst u16 bcm4306_sprom[] = { + 0x4001, 0x0000, 0x0453, 0x14e4, 0x4320, 0x8000, 0x0002, 0x0002, + 0x1000, 0x1800, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, +@@ -158,10 +159,12 @@ static __initconst u16 bcm43222_sprom[] + 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, + 0xffff, 0xffff, 0xffff, 0x0008, + }; ++#endif /* CONFIG_SSB_PCIHOST */ + + static struct ssb_sprom bcm63xx_sprom; + +-int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out) ++#if defined(CONFIG_SSB_PCIHOST) ++int bcm63xx_get_fallback_ssb_sprom(struct ssb_bus *bus, struct ssb_sprom *out) + { + if (bus->bustype == SSB_BUSTYPE_PCI) { + memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); +@@ -171,6 +174,20 @@ int bcm63xx_get_fallback_sprom(struct ss + return -EINVAL; + } + } ++#endif ++ ++#if defined(CONFIG_BCMA_HOST_PCI) ++int bcm63xx_get_fallback_bcma_sprom(struct bcma_bus *bus, struct ssb_sprom *out) ++{ ++ if (bus->hosttype == BCMA_HOSTTYPE_PCI) { ++ memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); ++ return 0; ++ } else { ++ printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); ++ return -EINVAL; ++ } ++} ++#endif + + /* FIXME: use lib_sprom after submission upstream */ + +@@ -654,10 +671,11 @@ int __init bcm63xx_register_fallback_spr + { + int ret = 0; + +-#ifdef CONFIG_SSB_PCIHOST ++#if defined(CONFIG_SSB_PCIHOST) || defined(CONFIG_BCMA_HOST_PCI) + u16 size = 0; + + switch (data->type) { ++#if defined(CONFIG_SSB_PCIHOST) + case SPROM_BCM4306: + memcpy(&template_sprom, &bcm4306_sprom, sizeof(bcm4306_sprom)); + size = ARRAY_SIZE(bcm4306_sprom); +@@ -678,6 +696,7 @@ int __init bcm63xx_register_fallback_spr + memcpy(&template_sprom, &bcm43222_sprom, sizeof(bcm43222_sprom)); + size = ARRAY_SIZE(bcm43222_sprom); + break; ++#endif + case SPROM_DEFAULT: + memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, + sizeof(bcm63xx_sprom)); +@@ -692,8 +711,19 @@ int __init bcm63xx_register_fallback_spr + memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et1mac, data->mac_addr, ETH_ALEN); ++#endif /* defined(CONFIG_SSB_PCIHOST) || defined(CONFIG_BCMA_HOST_PCI) */ ++ ++#if defined(CONFIG_SSB_PCIHOST) ++ ret = ssb_arch_register_fallback_sprom(&bcm63xx_get_fallback_ssb_sprom); ++ if (ret) ++ return ret; ++ ++#endif + +- ret = ssb_arch_register_fallback_sprom(&bcm63xx_get_fallback_sprom); ++#if defined(CONFIG_BCMA_HOST_PCI) ++ ret = bcma_arch_register_fallback_sprom(bcm63xx_get_fallback_bcma_sprom); ++ if (ret) ++ return ret; + #endif + return ret; + } diff --git a/target/linux/brcm63xx/patches-3.18/363-MIPS-BCM63XX-add-BCMA-based-sprom-templates.patch b/target/linux/brcm63xx/patches-3.18/363-MIPS-BCM63XX-add-BCMA-based-sprom-templates.patch new file mode 100644 index 0000000000..5c0abb90e3 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/363-MIPS-BCM63XX-add-BCMA-based-sprom-templates.patch @@ -0,0 +1,303 @@ +From 27bf70e3fe797691b17df07ecbfaf9f5a4419f49 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Wed, 30 Jul 2014 23:14:27 +0200 +Subject: [PATCH 08/10] MIPS: BCM63XX: add BCMA based sprom templates + +Add fallback sproms for BCM4313, BCM43131, BCM43217, BCM43225, BCM43227, +BCM43228, and BCM4331. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 256 +++++++++++++++++++++ + .../asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 8 + + 2 files changed, 264 insertions(+) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -161,6 +161,226 @@ static __initconst u16 bcm43222_sprom[] + }; + #endif /* CONFIG_SSB_PCIHOST */ + ++#if defined(CONFIG_BCMA_HOST_PCI) ++static __initconst u16 bcm4313_sprom[] = { ++ 0x2801, 0x0000, 0x0510, 0x14e4, 0x0078, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x1008, 0x0305, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x4727, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x5372, 0x1215, 0x2a00, 0x0800, 0x0800, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0003, 0xffff, 0x88ff, 0xffff, 0x0003, 0x0202, ++ 0xffff, 0x0011, 0x007a, 0x0000, 0x0000, 0x0000, 0x0000, 0x0201, ++ 0x0000, 0x7800, 0x7c0a, 0x0398, 0x0008, 0x0000, 0x0000, 0x0000, ++ 0x0044, 0x1684, 0xfd0d, 0xff35, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0048, 0xfed2, 0x15d9, 0xfac6, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0008, ++}; ++ ++static __initconst u16 bcm43131_sprom[] = { ++ 0x2801, 0x0000, 0x05f7, 0x14e4, 0x0070, 0xedbe, 0x1c00, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x1008, 0x0305, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x43aa, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x5372, 0x1280, 0x0200, 0x0000, 0x8800, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0003, 0xffff, 0x88ff, 0xffff, 0x0002, 0x0202, ++ 0xffff, 0x0022, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0415, ++ 0x0000, 0x7800, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xfe96, 0x192c, 0xfa15, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xfe91, 0x1950, 0xfa0a, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x4444, 0x4444, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x4444, 0x4444, 0x4444, 0x4444, 0x6666, 0x6666, 0x6666, ++ 0x6666, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0008, ++}; ++ ++static __initconst u16 bcm43217_sprom[] = { ++ 0x2801, 0x0000, 0x05e9, 0x14e4, 0x0070, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x1008, 0x0305, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x43a9, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x5372, 0x1252, 0x0200, 0x0000, 0x9800, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0003, 0xffff, 0x88ff, 0xffff, 0x0003, 0x0202, ++ 0xffff, 0x0033, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0415, ++ 0x0000, 0x7800, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xfe96, 0x192c, 0xfa15, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xfe91, 0x1950, 0xfa0a, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x4444, 0x4444, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x4444, 0x4444, 0x4444, 0x4444, 0x6666, 0x6666, 0x6666, ++ 0x6666, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x7a08, ++}; ++ ++static __initconst u16 bcm43225_sprom[] = { ++ 0x2801, 0x0000, 0x04da, 0x14e4, 0x0078, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0x1008, 0x0005, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x4357, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x5372, 0x1200, 0x0200, 0x0000, 0x1000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x88ff, 0xffff, 0xffff, 0x0303, 0x0202, ++ 0xffff, 0x0033, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x0325, ++ 0xffff, 0x7800, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x204e, 0xfead, 0x1611, 0xfa9a, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x204e, 0xfec1, 0x1674, 0xfab2, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x5555, 0x5555, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x5555, 0x7555, 0x5555, 0x7555, 0x5555, 0x7555, 0x5555, ++ 0x7555, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0002, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0008, ++}; ++ ++static __initconst u16 bcm43227_sprom[] = { ++ 0x2801, 0x0000, 0x0543, 0x14e4, 0x0070, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x1008, 0x0305, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x4358, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x5372, 0x1402, 0x0200, 0x0000, 0x0800, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0003, 0xffff, 0x88ff, 0xffff, 0x0003, 0x0202, ++ 0xffff, 0x0033, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0415, ++ 0x0000, 0x7800, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xff36, 0x16d2, 0xfaae, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xfeca, 0x159b, 0xfa80, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x4444, 0x4444, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x4444, 0x4444, 0x4444, 0x4444, 0x6666, 0x6666, 0x6666, ++ 0x6666, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0008, ++}; ++ ++static __initconst u16 bcm43228_sprom[] = { ++ 0x2801, 0x0000, 0x0011, 0x1028, 0x0070, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x1008, 0x0305, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x4359, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x5372, 0x1203, 0x0200, 0x0000, 0x0800, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0003, 0xffff, 0x88ff, 0xffff, 0x0303, 0x0202, ++ 0xffff, 0x0033, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0215, ++ 0x0215, 0x7800, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x204c, 0xff73, 0x1762, 0xfaa4, 0x3e34, 0x3434, 0xfea1, 0x154c, ++ 0xfad0, 0xfea1, 0x144c, 0xfafb, 0xfe7b, 0x13fe, 0xfafc, 0x0000, ++ 0x204c, 0xff41, 0x16a3, 0xfa8f, 0x3e34, 0x3434, 0xfe97, 0x1446, ++ 0xfb05, 0xfe97, 0x1346, 0xfb32, 0xfeb9, 0x1516, 0xfaee, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x4444, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x4444, 0x4444, 0x4444, 0x4444, 0x8888, 0x8888, 0x8888, ++ 0x8888, 0x0000, 0x0000, 0x0000, 0x0000, 0x3333, 0x3333, 0x3333, ++ 0x3333, 0x0000, 0x0000, 0x0000, 0x0000, 0x3333, 0x3333, 0x3333, ++ 0x3333, 0x0000, 0x0000, 0x0000, 0x0000, 0x3333, 0x3333, 0x3333, ++ 0x3333, 0x0000, 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xf008, ++}; ++ ++static __initconst u16 bcm4331_sprom[] = { ++ 0x2801, 0x0000, 0x0525, 0x14e4, 0x0078, 0xedbe, 0x0000, 0x2bc4, ++ 0x2a64, 0x2964, 0x2c64, 0x3ce7, 0x46ff, 0x47ff, 0x0c00, 0x0820, ++ 0x0030, 0x1002, 0x9f28, 0x5d44, 0x8080, 0x1d8f, 0x0032, 0x0100, ++ 0xdf00, 0x71f5, 0x8400, 0x0083, 0x8500, 0x2010, 0x0001, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0x1010, 0x0005, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x4331, 0x8000, 0x0002, 0x0000, 0x1f30, 0x1800, 0x0000, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x5372, 0x1104, 0x0200, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0xffff, 0x88ff, 0xffff, 0x0707, 0x0202, ++ 0xff02, 0x0077, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0x0325, ++ 0x0325, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x2048, 0xfe56, 0x16f2, 0xfa44, 0x3e3c, 0x3c3c, 0xfe77, 0x1657, ++ 0xfa75, 0xffff, 0xffff, 0xffff, 0xfe76, 0x15da, 0xfa85, 0x0000, ++ 0x2048, 0xfe5c, 0x16b5, 0xfa56, 0x3e3c, 0x3c3c, 0xfe7c, 0x169d, ++ 0xfa6b, 0xffff, 0xffff, 0xffff, 0xfe7a, 0x1597, 0xfa97, 0x0000, ++ 0x2048, 0xfe68, 0x1734, 0xfa46, 0x3e3c, 0x3c3c, 0xfe7f, 0x15e4, ++ 0xfa94, 0xffff, 0xffff, 0xffff, 0xfe7d, 0x1582, 0xfa9f, 0x0000, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, ++ 0x0000, 0x0000, 0x0000, 0x0000, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, 0xffff, ++ 0xffff, 0xffff, 0xffff, 0x0009, ++}; ++ ++#endif /* CONFIG_BCMA_HOST_PCI */ ++ + static struct ssb_sprom bcm63xx_sprom; + + #if defined(CONFIG_SSB_PCIHOST) +@@ -697,6 +917,42 @@ int __init bcm63xx_register_fallback_spr + size = ARRAY_SIZE(bcm43222_sprom); + break; + #endif ++#if defined(CONFIG_BCMA_HOST_PCI) ++ case SPROM_BCM4313: ++ memcpy(&template_sprom, &bcm4313_sprom, ++ sizeof(bcm4313_sprom)); ++ size = ARRAY_SIZE(bcm4313_sprom); ++ break; ++ case SPROM_BCM43131: ++ memcpy(&template_sprom, &bcm43131_sprom, ++ sizeof(bcm43131_sprom)); ++ size = ARRAY_SIZE(bcm43131_sprom); ++ break; ++ case SPROM_BCM43217: ++ memcpy(&template_sprom, &bcm43217_sprom, ++ sizeof(bcm43217_sprom)); ++ size = ARRAY_SIZE(bcm43217_sprom); ++ break; ++ case SPROM_BCM43225: ++ memcpy(&template_sprom, &bcm43225_sprom, ++ sizeof(bcm43225_sprom)); ++ size = ARRAY_SIZE(bcm43225_sprom); ++ break; ++ case SPROM_BCM43227: ++ memcpy(&template_sprom, &bcm43227_sprom, ++ sizeof(bcm43227_sprom)); ++ size = ARRAY_SIZE(bcm43227_sprom); ++ break; ++ case SPROM_BCM43228: ++ memcpy(&template_sprom, &bcm43228_sprom, ++ sizeof(bcm43228_sprom)); ++ size = ARRAY_SIZE(bcm43228_sprom); ++ break; ++ case SPROM_BCM4331: ++ memcpy(&template_sprom, &bcm4331_sprom, sizeof(&bcm4331_sprom)); ++ size = ARRAY_SIZE(bcm4331_sprom); ++ break; ++#endif + case SPROM_DEFAULT: + memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, + sizeof(bcm63xx_sprom)); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -11,6 +11,14 @@ enum sprom_type { + SPROM_BCM4321, + SPROM_BCM4322, + SPROM_BCM43222, ++ /* BCMA based */ ++ SPROM_BCM4313, ++ SPROM_BCM43131, ++ SPROM_BCM43217, ++ SPROM_BCM43225, ++ SPROM_BCM43227, ++ SPROM_BCM43228, ++ SPROM_BCM4331, + }; + + struct fallback_sprom_data { diff --git a/target/linux/brcm63xx/patches-3.18/364-MIPS-BCM63XX-allow-board-files-to-provide-sprom-fixu.patch b/target/linux/brcm63xx/patches-3.18/364-MIPS-BCM63XX-allow-board-files-to-provide-sprom-fixu.patch new file mode 100644 index 0000000000..74c2846d5f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/364-MIPS-BCM63XX-allow-board-files-to-provide-sprom-fixu.patch @@ -0,0 +1,67 @@ +From 8575548b08e33c9ff4fd540abec09dd177e33682 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Thu, 31 Jul 2014 19:12:33 +0200 +Subject: [PATCH 09/10] MIPS: BCM63XX: allow board files to provide sprom + fixups + +Allow board_info files to supply fixups for the base sproms to adapt +them to the actual used sprom contents in case they do not use the +default ones. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 14 +++++++++++++- + .../mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 8 ++++++++ + 2 files changed, 21 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -883,6 +883,14 @@ static int sprom_extract(struct ssb_spro + return 0; + } + ++void sprom_apply_fixups(u16 *sprom, struct sprom_fixup *fixups, int n) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < n; i++) ++ sprom[fixups[i].offset] = fixups[i].value; ++} ++ + static __initdata u16 template_sprom[220]; + #endif + +@@ -961,8 +969,12 @@ int __init bcm63xx_register_fallback_spr + return -EINVAL; + } + +- if (size > 0) ++ if (size > 0) { ++ sprom_apply_fixups(template_sprom, data->board_fixups, ++ data->num_board_fixups); ++ + sprom_extract(&bcm63xx_sprom, template_sprom, size); ++ } + + memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); + memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -21,9 +21,17 @@ enum sprom_type { + SPROM_BCM4331, + }; + ++struct sprom_fixup { ++ u16 offset; ++ u16 value; ++}; ++ + struct fallback_sprom_data { + u8 mac_addr[ETH_ALEN]; + enum sprom_type type; ++ ++ struct sprom_fixup *board_fixups; ++ unsigned int num_board_fixups; + }; + + int bcm63xx_register_fallback_sprom(struct fallback_sprom_data *data); diff --git a/target/linux/brcm63xx/patches-3.18/365-MIPS-BCM63XX-allow-setting-a-pci-bus-device-for-fall.patch b/target/linux/brcm63xx/patches-3.18/365-MIPS-BCM63XX-allow-setting-a-pci-bus-device-for-fall.patch new file mode 100644 index 0000000000..40591e5f2e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/365-MIPS-BCM63XX-allow-setting-a-pci-bus-device-for-fall.patch @@ -0,0 +1,102 @@ +From f393eaacf178e7e8a61eb11a96edd7dfb35cb49d Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Thu, 31 Jul 2014 20:39:44 +0200 +Subject: [PATCH 10/10] MIPS: BCM63XX: allow setting a pci bus/device for + fallback sprom + +Warn if the set pci bus/slot does not match the actual request. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/sprom.c | 31 ++++++++++++++++++---- + .../asm/mach-bcm63xx/bcm63xx_fallback_sprom.h | 3 +++ + 2 files changed, 29 insertions(+), 5 deletions(-) + +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -381,13 +381,25 @@ static __initconst u16 bcm4331_sprom[] = + + #endif /* CONFIG_BCMA_HOST_PCI */ + +-static struct ssb_sprom bcm63xx_sprom; ++struct fallback_sprom_match { ++ u8 pci_bus; ++ u8 pci_dev; ++ struct ssb_sprom sprom; ++}; ++ ++static struct fallback_sprom_match fallback_sprom; + + #if defined(CONFIG_SSB_PCIHOST) + int bcm63xx_get_fallback_ssb_sprom(struct ssb_bus *bus, struct ssb_sprom *out) + { + if (bus->bustype == SSB_BUSTYPE_PCI) { +- memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); ++ if (bus->host_pci->bus->number != fallback_sprom.pci_bus || ++ PCI_SLOT(bus->host_pci->devfn) != fallback_sprom.pci_dev) ++ pr_warn("ssb_fallback_sprom: pci bus/device num mismatch: expected %i/%i, but got %i/%i\n", ++ fallback_sprom.pci_bus, fallback_sprom.pci_dev, ++ bus->host_pci->bus->number, ++ PCI_SLOT(bus->host_pci->devfn)); ++ memcpy(out, &fallback_sprom.sprom, sizeof(struct ssb_sprom)); + return 0; + } else { + printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); +@@ -400,7 +412,13 @@ int bcm63xx_get_fallback_ssb_sprom(struc + int bcm63xx_get_fallback_bcma_sprom(struct bcma_bus *bus, struct ssb_sprom *out) + { + if (bus->hosttype == BCMA_HOSTTYPE_PCI) { +- memcpy(out, &bcm63xx_sprom, sizeof(struct ssb_sprom)); ++ if (bus->host_pci->bus->number != fallback_sprom.pci_bus || ++ PCI_SLOT(bus->host_pci->devfn) != fallback_sprom.pci_dev) ++ pr_warn("bcma_fallback_sprom: pci bus/device num mismatch: expected %i/%i, but got %i/%i\n", ++ fallback_sprom.pci_bus, fallback_sprom.pci_dev, ++ bus->host_pci->bus->number, ++ PCI_SLOT(bus->host_pci->devfn)); ++ memcpy(out, &fallback_sprom.sprom, sizeof(struct ssb_sprom)); + return 0; + } else { + printk(KERN_ERR PFX "unable to fill SPROM for given bustype.\n"); +@@ -962,8 +980,8 @@ int __init bcm63xx_register_fallback_spr + break; + #endif + case SPROM_DEFAULT: +- memcpy(&bcm63xx_sprom, &bcm63xx_default_sprom, +- sizeof(bcm63xx_sprom)); ++ memcpy(&fallback_sprom.sprom, &bcm63xx_default_sprom, ++ sizeof(bcm63xx_default_sprom)); + break; + default: + return -EINVAL; +@@ -973,12 +991,15 @@ int __init bcm63xx_register_fallback_spr + sprom_apply_fixups(template_sprom, data->board_fixups, + data->num_board_fixups); + +- sprom_extract(&bcm63xx_sprom, template_sprom, size); ++ sprom_extract(&fallback_sprom.sprom, template_sprom, size); + } + +- memcpy(bcm63xx_sprom.il0mac, data->mac_addr, ETH_ALEN); +- memcpy(bcm63xx_sprom.et0mac, data->mac_addr, ETH_ALEN); +- memcpy(bcm63xx_sprom.et1mac, data->mac_addr, ETH_ALEN); ++ memcpy(fallback_sprom.sprom.il0mac, data->mac_addr, ETH_ALEN); ++ memcpy(fallback_sprom.sprom.et0mac, data->mac_addr, ETH_ALEN); ++ memcpy(fallback_sprom.sprom.et1mac, data->mac_addr, ETH_ALEN); ++ ++ fallback_sprom.pci_bus = data->pci_bus; ++ fallback_sprom.pci_dev = data->pci_dev; + #endif /* defined(CONFIG_SSB_PCIHOST) || defined(CONFIG_BCMA_HOST_PCI) */ + + #if defined(CONFIG_SSB_PCIHOST) +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_fallback_sprom.h +@@ -30,6 +30,9 @@ struct fallback_sprom_data { + u8 mac_addr[ETH_ALEN]; + enum sprom_type type; + ++ u8 pci_bus; ++ u8 pci_dev; ++ + struct sprom_fixup *board_fixups; + unsigned int num_board_fixups; + }; diff --git a/target/linux/brcm63xx/patches-3.18/366-MIPS-add-support-for-vmlinux.bin-appended-DTB.patch b/target/linux/brcm63xx/patches-3.18/366-MIPS-add-support-for-vmlinux.bin-appended-DTB.patch new file mode 100644 index 0000000000..7c19ee590d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/366-MIPS-add-support-for-vmlinux.bin-appended-DTB.patch @@ -0,0 +1,124 @@ +From 318c1fce4aeef298cbb6153416c499c94ad7cda0 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 24 Jun 2014 10:53:15 +0200 +Subject: [PATCH RFC v3] MIPS: add support for vmlinux.bin appended DTB + +Add support for populating initial_boot_params through a dtb +blob appended to raw vmlinux.bin. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- +Changes RFC v2 -> v3 + +* fixed !smp kernels (TODO: move it to its own patch + +Changes RFC v1 -> v2 + +* changed all occurences of vmlinux to vmlinux.bin +* clarified this applies to the raw vmlinux.bin without decompressor +* s/initial_device_params/initial_boot_params/ + +Initial comments by me still valid: + +Mostly adapted from how ARM is doing it. + +Sent as an RFC PATCH because I am not sure if this is the right way to +it, and whether storing the pointer in initial_boot_params is a good +idea, or a new variable should be introduced. + +The reasoning for initial_boot_params is that there is no common +MIPS interface yet, so the next best thing was using that. This also +has the advantage of keeping the original fw_args intact. + +This patch works for me on bcm63xx, where the bootloader expects +an lzma compressed kernel, so I didn't want to double compress using +the in-kernel compressed kernel support. + +Completely untested on anything except MIPS32 / big endian. + + arch/mips/Kconfig | 18 ++++++++++++++++++ + arch/mips/kernel/head.S | 19 +++++++++++++++++++ + arch/mips/kernel/vmlinux.lds.S | 7 +++++++ + 3 files changed, 43 insertions(+) + +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -2645,6 +2645,24 @@ config RAPIDIO + + source "drivers/rapidio/Kconfig" + ++config MIPS_APPENDED_DTB ++ bool "Use appended device tree blob to vmlinux.bin (EXPERIMENTAL)" ++ depends on OF ++ help ++ With this option, the boot code will look for a device tree binary ++ DTB) appended to raw vmlinux.bin (without decompressor). ++ (e.g. cat vmlinux.bin <filename>.dtb > vmlinux_w_dtb). ++ ++ This is meant as a backward compatibility convenience for those ++ systems with a bootloader that can't be upgraded to accommodate ++ the documented boot protocol using a device tree. ++ ++ Beware that there is very little in terms of protection against ++ this option being confused by leftover garbage in memory that might ++ look like a DTB header after a reboot if no actual DTB is appended ++ to vmlinux.bin. Do not leave this option active in a production kernel ++ if you don't intend to always append a DTB. ++ + endmenu + + menu "Executable file formats" +--- a/arch/mips/kernel/head.S ++++ b/arch/mips/kernel/head.S +@@ -100,6 +100,22 @@ NESTED(kernel_entry, 16, sp) # kernel + jr t0 + 0: + ++#ifdef CONFIG_MIPS_APPENDED_DTB ++ PTR_LA t0, __appended_dtb ++ PTR_LI t3, 0 ++ ++#ifdef CONFIG_CPU_BIG_ENDIAN ++ PTR_LI t1, 0xd00dfeed ++#else ++ PTR_LI t1, 0xedfe0dd0 ++#endif ++ LONG_L t2, (t0) ++ bne t1, t2, not_found ++ ++ PTR_LA t3, __appended_dtb ++ ++not_found: ++#endif + PTR_LA t0, __bss_start # clear .bss + LONG_S zero, (t0) + PTR_LA t1, __bss_stop - LONGSIZE +@@ -113,6 +129,10 @@ NESTED(kernel_entry, 16, sp) # kernel + LONG_S a2, fw_arg2 + LONG_S a3, fw_arg3 + ++#ifdef CONFIG_MIPS_APPENDED_DTB ++ LONG_S t3, initial_boot_params ++#endif ++ + MTC0 zero, CP0_CONTEXT # clear context register + PTR_LA $28, init_thread_union + /* Set the SP after an empty pt_regs. */ +--- a/arch/mips/kernel/vmlinux.lds.S ++++ b/arch/mips/kernel/vmlinux.lds.S +@@ -125,8 +125,14 @@ SECTIONS + .exit.data : { + EXIT_DATA + } +- ++#ifdef CONFIG_SMP + PERCPU_SECTION(1 << CONFIG_MIPS_L1_CACHE_SHIFT) ++#endif ++#ifdef CONFIG_MIPS_APPENDED_DTB ++ __appended_dtb = .; ++ /* leave space for appended DTB */ ++ . = . + 0x100000; ++#endif + /* + * Align to 64K in attempt to eliminate holes before the + * .bss..swapper_pg_dir section at the start of .bss. This diff --git a/target/linux/brcm63xx/patches-3.18/367-MIPS-BCM63XX-add-support-for-loading-DTB.patch b/target/linux/brcm63xx/patches-3.18/367-MIPS-BCM63XX-add-support-for-loading-DTB.patch new file mode 100644 index 0000000000..577df55d0e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/367-MIPS-BCM63XX-add-support-for-loading-DTB.patch @@ -0,0 +1,96 @@ +From db896341299cbcb703821228574ba9b79b6a3565 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Tue, 24 Jun 2014 10:57:51 +0200 +Subject: [PATCH 45/48] MIPS: BCM63XX: add support for loading DTB + +--- + arch/mips/bcm63xx/boards/Kconfig | 4 ++++ + arch/mips/bcm63xx/boards/board_common.c | 34 +++++++++++++++++++++++++++++++++ + 2 files changed, 38 insertions(+) + +--- a/arch/mips/bcm63xx/boards/Kconfig ++++ b/arch/mips/bcm63xx/boards/Kconfig +@@ -1,6 +1,10 @@ + menu "Board support" + depends on BCM63XX + ++config BOARD_BCM63XX_DT ++ bool "Device Tree boards (experimential)" ++ select USE_OF ++ + config BOARD_BCM963XX + bool "Generic Broadcom 963xx boards" + select SSB +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -10,6 +10,8 @@ + #include <linux/init.h> + #include <linux/kernel.h> + #include <linux/string.h> ++#include <linux/of_fdt.h> ++#include <linux/of_platform.h> + #include <linux/platform_device.h> + #include <linux/ssb/ssb.h> + #include <linux/gpio_keys.h> +@@ -17,6 +19,7 @@ + #include <asm/addrspace.h> + #include <asm/bootinfo.h> + #include <asm/fw/cfe/cfe_api.h> ++#include <asm/prom.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> + #include <bcm63xx_dev_uart.h> +@@ -129,8 +132,23 @@ void __init board_setup(void) + /* make sure we're running on expected cpu */ + if (bcm63xx_get_cpu_id() != board.expected_cpu_id) + panic("unexpected CPU for bcm963xx board"); ++ ++#if CONFIG_OF ++ if (initial_boot_params) ++ __dt_setup_arch(initial_boot_params); ++#endif + } + ++#if CONFIG_OF ++void __init device_tree_init(void) ++{ ++ if (!initial_boot_params) ++ return; ++ ++ unflatten_and_copy_device_tree(); ++} ++#endif ++ + static struct gpio_led_platform_data bcm63xx_led_data; + + static struct platform_device bcm63xx_gpio_leds = { +@@ -149,6 +167,13 @@ static struct platform_device bcm63xx_gp + .dev.platform_data = &bcm63xx_gpio_keys_data, + }; + ++#if CONFIG_OF ++static struct of_device_id of_ids[] = { ++ { /* filled at runtime */ }, ++ { .compatible = "simple-bus" }, ++ { }, ++}; ++#endif + /* + * third stage init callback, register all board devices. + */ +@@ -158,6 +183,15 @@ int __init board_register_devices(void) + int led_count = 0; + int usbh_ports = 0; + ++#if CONFIG_OF ++ if (of_have_populated_dt()) { ++ snprintf(of_ids[0].compatible, sizeof(of_ids[0].compatible), ++ "brcm,bcm%x", bcm63xx_get_cpu_id()); ++ ++ of_platform_populate(NULL, of_ids, NULL, NULL); ++ } ++#endif ++ + if (board.has_uart0) + bcm63xx_uart_register(0); + diff --git a/target/linux/brcm63xx/patches-3.18/368-MIPS-BCM63XX-add-support-for-matching-the-board_info.patch b/target/linux/brcm63xx/patches-3.18/368-MIPS-BCM63XX-add-support-for-matching-the-board_info.patch new file mode 100644 index 0000000000..afe537a5a5 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/368-MIPS-BCM63XX-add-support-for-matching-the-board_info.patch @@ -0,0 +1,95 @@ +From 25bf2b5836c892f091651d8a3384c9c57ce1b400 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Thu, 26 Jun 2014 12:51:00 +0200 +Subject: [PATCH 46/48] MIPS: BCM63XX: add support for matching the board_info + by dtb + +Allow using the passed dtb's compatible property to match board_info +structs instead of nvram's boardname field, which is not unique anyway. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 15 +++++++++++++++ + arch/mips/bcm63xx/boards/board_common.c | 18 ++++++++++++++++++ + arch/mips/bcm63xx/boards/board_common.h | 3 +++ + 3 files changed, 36 insertions(+) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -735,6 +735,10 @@ static const struct board_info __initcon + #endif + }; + ++static struct of_device_id const bcm963xx_boards_dt[] = { ++ { }, ++}; ++ + /* + * early init callback, read nvram data from flash and checksum it + */ +@@ -746,6 +750,7 @@ void __init board_bcm963xx_init(void) + char *board_name = NULL; + u32 val; + struct bcm_hcs *hcs; ++ const struct of_device_id *board_match; + + /* read base address of boot chip select (0) + * 6328/6362 do not have MPI but boot from a fixed address +@@ -785,6 +790,16 @@ void __init board_bcm963xx_init(void) + } else { + board_name = bcm63xx_nvram_get_name(); + } ++ ++ /* find board by compat */ ++ board_match = bcm63xx_match_board(bcm963xx_boards_dt); ++ if (board_match) { ++ board_early_setup(board_match->data, ++ bcm63xx_nvram_get_mac_address); ++ ++ return; ++ } ++ + /* find board by name */ + for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) { + if (strncmp(board_name, bcm963xx_boards[i]->name, 16)) +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -281,3 +281,21 @@ int __init board_register_devices(void) + + return 0; + } ++ ++const struct of_device_id * __init bcm63xx_match_board(const struct of_device_id *m) ++{ ++ const struct of_device_id *match; ++ unsigned long dt_root; ++ ++ if (!IS_ENABLED(CONFIG_OF) || !initial_boot_params) ++ return NULL; ++ ++ dt_root = of_get_flat_dt_root(); ++ ++ for (match = m; match->compatible[0]; match++) { ++ if (of_flat_dt_is_compatible(dt_root, match->compatible)) ++ return match; ++ } ++ ++ return NULL; ++} +--- a/arch/mips/bcm63xx/boards/board_common.h ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -1,11 +1,14 @@ + #ifndef __BOARD_COMMON_H + #define __BOARD_COMMON_H + ++#include <linux/of.h> + #include <board_bcm963xx.h> + + void board_early_setup(const struct board_info *board, + int (*get_mac_address)(u8 mac[ETH_ALEN])); + ++const struct of_device_id *bcm63xx_match_board(const struct of_device_id *); ++ + #if defined(CONFIG_BOARD_BCM963XX) + void board_bcm963xx_init(void); + #else diff --git a/target/linux/brcm63xx/patches-3.18/369-MIPS-BCM63XX-populate-the-compatible-to-board_info-l.patch b/target/linux/brcm63xx/patches-3.18/369-MIPS-BCM63XX-populate-the-compatible-to-board_info-l.patch new file mode 100644 index 0000000000..a38fca589f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/369-MIPS-BCM63XX-populate-the-compatible-to-board_info-l.patch @@ -0,0 +1,62 @@ +From e71eea9953c774dfadb754258824fb1888c279f4 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Fri, 21 Nov 2014 16:54:06 +0100 +Subject: [PATCH 47/48] MIPS: BCM63XX: populate the compatible to board_info + list + +Populate the compatible to board_info list to allow dtbs to be used +for known boards. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 35 +++++++++++++++++++++++++++++ + 1 file changed, 35 insertions(+) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -736,6 +736,45 @@ static const struct board_info __initcon + }; + + static struct of_device_id const bcm963xx_boards_dt[] = { ++#ifdef CONFIG_OF ++#ifdef CONFIG_BCM63XX_CPU_3368 ++ { .compatible = "netgear,cvg834g", .data = &board_cvg834g, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6328 ++ { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6338 ++ { .compatible = "brcm,bcm96338gw", .data = &board_96338gw, }, ++ { .compatible = "brcm,bcm96338w", .data = &board_96338w, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6345 ++ { .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6348 ++ { .compatible = "brcm,bcm96348r", .data = &board_96348r, }, ++ { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, }, ++ { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, }, ++ { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, }, ++ { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, ++ { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, ++ { .compatible = "sagem,f@st2404", .data = &board_FAST2404, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6358 ++ { .compatible = "alcatel,rg100a", .data = &board_96358vw2, }, ++ { .compatible = "brcm,bcm96358vw", .data = &board_96358vw, }, ++ { .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, }, ++ { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, ++ { .compatible = "pirelli,a226g", .data = &board_DWVS0, }, ++ { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, ++ { .compatible = "pirelli,a226m-fwb", .data = &board_DWVS0, }, ++ { .compatible = "pirelli,agpf-s0", .data = &board_AGPFS0, }, ++#endif ++#ifdef CONFIG_BCM63XX_CPU_6368 ++#endif ++#ifdef CONFIG_BCM63XX_CPU_63268 ++ { .compatible = "brcm,bcm963268bu_p300", .data = &board_963268bu_p300, }, ++#endif ++#endif /* CONFIG_OF */ + { }, + }; + diff --git a/target/linux/brcm63xx/patches-3.18/371_add_of_node_available_by_alias.patch b/target/linux/brcm63xx/patches-3.18/371_add_of_node_available_by_alias.patch new file mode 100644 index 0000000000..99d778deb7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/371_add_of_node_available_by_alias.patch @@ -0,0 +1,37 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -147,6 +147,18 @@ void __init device_tree_init(void) + + unflatten_and_copy_device_tree(); + } ++ ++int board_of_device_present(const char *alias) ++{ ++ bool present; ++ struct device_node *np; ++ ++ np = of_find_node_by_path(alias); ++ present = of_device_is_available(np); ++ of_node_put(np); ++ ++ return present; ++} + #endif + + static struct gpio_led_platform_data bcm63xx_led_data; +--- a/arch/mips/bcm63xx/boards/board_common.h ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -15,4 +15,13 @@ void board_bcm963xx_init(void); + static inline void board_bcm963xx_init(void) { } + #endif + ++#if defined(CONFIG_OF) ++int board_of_device_present(const char *alias); ++#else ++static inline void board_of_device_present(const char *alias) ++{ ++ return 0; ++} ++#endif ++ + #endif /* __BOARD_COMMON_H */ diff --git a/target/linux/brcm63xx/patches-3.18/372_dont_register_pflash_when_available_in_dtb.patch b/target/linux/brcm63xx/patches-3.18/372_dont_register_pflash_when_available_in_dtb.patch new file mode 100644 index 0000000000..88efc2360b --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/372_dont_register_pflash_when_available_in_dtb.patch @@ -0,0 +1,21 @@ +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -22,6 +22,8 @@ + #include <bcm63xx_regs.h> + #include <bcm63xx_io.h> + ++#include "boards/board_common.h" ++ + static int flash_type; + + static struct mtd_partition mtd_partitions[] = { +@@ -164,6 +166,9 @@ int __init bcm63xx_flash_register(void) + + switch (flash_type) { + case BCM63XX_FLASH_TYPE_PARALLEL: ++ /* don't register when already registered through from dtb */ ++ if (board_of_device_present("pflash")) ++ return 0; + + if (!mtd_resources[0].start) { + /* read base address of boot chip select (0) */ diff --git a/target/linux/brcm63xx/patches-3.18/373-MIPS-BCM63XX-register-interrupt-controllers-through-.patch b/target/linux/brcm63xx/patches-3.18/373-MIPS-BCM63XX-register-interrupt-controllers-through-.patch new file mode 100644 index 0000000000..3b15589baa --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/373-MIPS-BCM63XX-register-interrupt-controllers-through-.patch @@ -0,0 +1,36 @@ +From 7c22b08baba941a8c83072047b0d2b55a6b952aa Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Mon, 1 Dec 2014 00:20:07 +0100 +Subject: [PATCH] MIPS: BCM63XX: register interrupt controllers through DT + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/irq.c | 10 +++++++++- + 1 file changed, 9 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/irq.c ++++ b/arch/mips/bcm63xx/irq.c +@@ -15,6 +15,8 @@ + #include <linux/irqchip.h> + #include <linux/irqchip/irq-bcm6345-ext-intc.h> + #include <linux/irqchip/irq-bcm6345-l2-intc.h> ++#include <linux/of.h> ++#include <linux/of_fdt.h> + #include <asm/irq_cpu.h> + #include <asm/mipsregs.h> + #include <bcm63xx_cpu.h> +@@ -189,7 +191,13 @@ static void bcm63xx_init_irq(void) + ext_shift); + } + ++OF_DECLARE_2(irqchip, mips_cpu_intc, "mti,cpu-interrupt-controller", ++ mips_cpu_irq_of_init); ++ + void __init arch_init_irq(void) + { +- bcm63xx_init_irq(); ++ if (initial_boot_params) ++ irqchip_init(); ++ else ++ bcm63xx_init_irq(); + } diff --git a/target/linux/brcm63xx/patches-3.18/400-bcm963xx_flashmap.patch b/target/linux/brcm63xx/patches-3.18/400-bcm963xx_flashmap.patch new file mode 100644 index 0000000000..03534c0aab --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/400-bcm963xx_flashmap.patch @@ -0,0 +1,65 @@ +From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001 +From: Axel Gembe <ago@bastart.eu.org> +Date: Mon, 12 May 2008 18:54:09 +0200 +Subject: [PATCH] bcm963xx: flashmap support + +Signed-off-by: Axel Gembe <ago@bastart.eu.org> +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 19 +---------------- + drivers/mtd/maps/bcm963xx-flash.c | 32 ++++++++++++++++++++++++---- + drivers/mtd/redboot.c | 13 +++++++++-- + 3 files changed, 38 insertions(+), 26 deletions(-) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -34,7 +34,7 @@ static struct mtd_partition mtd_partitio + } + }; + +-static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL }; ++static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; + + static struct physmap_flash_data flash_data = { + .width = 2, +--- a/drivers/mtd/redboot.c ++++ b/drivers/mtd/redboot.c +@@ -72,6 +72,7 @@ static int parse_redboot_partitions(stru + int nulllen = 0; + int numslots; + unsigned long offset; ++ unsigned long fis_origin = 0; + #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED + static char nullstring[] = "unallocated"; + #endif +@@ -176,6 +177,16 @@ static int parse_redboot_partitions(stru + goto out; + } + ++ if (data && data->origin) { ++ fis_origin = data->origin; ++ } else { ++ for (i = 0; i < numslots; i++) { ++ if (!strncmp(buf[i].name, "RedBoot", 8)) { ++ fis_origin = (buf[i].flash_base & (master->size << 1) - 1); ++ } ++ } ++ } ++ + for (i = 0; i < numslots; i++) { + struct fis_list *new_fl, **prev; + +@@ -196,10 +207,10 @@ static int parse_redboot_partitions(stru + goto out; + } + new_fl->img = &buf[i]; +- if (data && data->origin) +- buf[i].flash_base -= data->origin; +- else +- buf[i].flash_base &= master->size-1; ++ if (fis_origin) ++ buf[i].flash_base -= fis_origin; ++ ++ buf[i].flash_base &= (master->size << 1) - 1; + + /* I'm sure the JFFS2 code has done me permanent damage. + * I now think the following is _normal_ diff --git a/target/linux/brcm63xx/patches-3.18/401-bcm963xx_real_rootfs_length.patch b/target/linux/brcm63xx/patches-3.18/401-bcm963xx_real_rootfs_length.patch new file mode 100644 index 0000000000..caf8b9514d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/401-bcm963xx_real_rootfs_length.patch @@ -0,0 +1,27 @@ +--- a/include/uapi/linux/bcm963xx_tag.h ++++ b/include/uapi/linux/bcm963xx_tag.h +@@ -85,8 +85,10 @@ struct bcm_tag { + __u32 rootfs_crc; + /* 224-227: CRC32 of kernel partition */ + __u32 kernel_crc; +- /* 228-235: Unused at present */ +- char reserved1[8]; ++ /* 228-231: Image sequence number */ ++ char image_sequence[4]; ++ /* 222-235: Openwrt: real rootfs length */ ++ __u32 real_rootfs_length; + /* 236-239: CRC32 of header excluding last 20 bytes */ + __u32 header_crc; + /* 240-255: Unused at present */ +--- a/drivers/mtd/bcm63xxpart.c ++++ b/drivers/mtd/bcm63xxpart.c +@@ -110,7 +110,8 @@ static int bcm63xx_parse_cfe_partitions( + } else { + /* OpenWrt layout */ + rootfsaddr = kerneladdr + kernellen; +- rootfslen = spareaddr - rootfsaddr; ++ rootfslen = buf->real_rootfs_length; ++ spareaddr = rootfsaddr + rootfslen; + } + } else { + pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n", diff --git a/target/linux/brcm63xx/patches-3.18/402_bcm63xx_enet_vlan_incoming_fixed.patch b/target/linux/brcm63xx/patches-3.18/402_bcm63xx_enet_vlan_incoming_fixed.patch new file mode 100644 index 0000000000..8cb8099e97 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/402_bcm63xx_enet_vlan_incoming_fixed.patch @@ -0,0 +1,11 @@ +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c +@@ -1632,7 +1632,7 @@ static int compute_hw_mtu(struct bcm_ene + actual_mtu = mtu; + + /* add ethernet header + vlan tag size */ +- actual_mtu += VLAN_ETH_HLEN; ++ actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN; + + if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU) + return -EINVAL; diff --git a/target/linux/brcm63xx/patches-3.18/403-6358-enet1-external-mii-clk.patch b/target/linux/brcm63xx/patches-3.18/403-6358-enet1-external-mii-clk.patch new file mode 100644 index 0000000000..0745c3cc8f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/403-6358-enet1-external-mii-clk.patch @@ -0,0 +1,22 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -104,6 +104,8 @@ void __init board_early_setup(const stru + if (BCMCPU_IS_6348()) + val |= GPIO_MODE_6348_G3_EXT_MII | + GPIO_MODE_6348_G0_EXT_MII; ++ else if (BCMCPU_IS_6358()) ++ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV; + } + + bcm_gpio_writel(val, GPIO_MODE_REG); +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -651,6 +651,8 @@ + #define GPIO_MODE_6358_EXTRA_SPI_SS (1 << 7) + #define GPIO_MODE_6358_SERIAL_LED (1 << 10) + #define GPIO_MODE_6358_UTOPIA (1 << 12) ++#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 30) ++#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 31) + + #define GPIO_MODE_6368_ANALOG_AFE_0 (1 << 0) + #define GPIO_MODE_6368_ANALOG_AFE_1 (1 << 1) diff --git a/target/linux/brcm63xx/patches-3.18/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch b/target/linux/brcm63xx/patches-3.18/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch new file mode 100644 index 0000000000..702e4ef141 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/404-NET-bcm63xx_enet-move-phy_-dis-connect-into-probe-re.patch @@ -0,0 +1,169 @@ +From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Fri, 6 Jan 2012 12:24:18 +0100 +Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove + +Only connect/disconnect the phy during probe and remove, not during any +open/close. The phy seldom changes during the runtime, and disconnecting +the phy during close will prevent it from keeping any configuration over +a down/up cycle. + +Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> +--- + drivers/net/ethernet/broadcom/bcm63xx_enet.c | 84 +++++++++++++------------- + 1 files changed, 41 insertions(+), 43 deletions(-) + +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c +@@ -870,10 +870,8 @@ static int bcm_enet_open(struct net_devi + struct bcm_enet_priv *priv; + struct sockaddr addr; + struct device *kdev; +- struct phy_device *phydev; + int i, ret; + unsigned int size; +- char phy_id[MII_BUS_ID_SIZE + 3]; + void *p; + u32 val; + +@@ -881,40 +879,10 @@ static int bcm_enet_open(struct net_devi + kdev = &priv->pdev->dev; + + if (priv->has_phy) { +- /* connect to PHY */ +- snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, +- priv->mii_bus->id, priv->phy_id); +- +- phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, +- PHY_INTERFACE_MODE_MII); +- +- if (IS_ERR(phydev)) { +- dev_err(kdev, "could not attach to PHY\n"); +- return PTR_ERR(phydev); +- } +- +- /* mask with MAC supported features */ +- phydev->supported &= (SUPPORTED_10baseT_Half | +- SUPPORTED_10baseT_Full | +- SUPPORTED_100baseT_Half | +- SUPPORTED_100baseT_Full | +- SUPPORTED_Autoneg | +- SUPPORTED_Pause | +- SUPPORTED_MII); +- phydev->advertising = phydev->supported; +- +- if (priv->pause_auto && priv->pause_rx && priv->pause_tx) +- phydev->advertising |= SUPPORTED_Pause; +- else +- phydev->advertising &= ~SUPPORTED_Pause; +- +- dev_info(kdev, "attached PHY at address %d [%s]\n", +- phydev->addr, phydev->drv->name); +- ++ /* Reset state */ + priv->old_link = 0; + priv->old_duplex = -1; + priv->old_pause = -1; +- priv->phydev = phydev; + } + + /* mask all interrupts and request them */ +@@ -924,7 +892,7 @@ static int bcm_enet_open(struct net_devi + + ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); + if (ret) +- goto out_phy_disconnect; ++ return ret; + + ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, 0, + dev->name, dev); +@@ -1127,9 +1095,6 @@ out_freeirq_rx: + out_freeirq: + free_irq(dev->irq, dev); + +-out_phy_disconnect: +- phy_disconnect(priv->phydev); +- + return ret; + } + +@@ -1234,12 +1199,6 @@ static int bcm_enet_stop(struct net_devi + free_irq(priv->irq_rx, dev); + free_irq(dev->irq, dev); + +- /* release phy */ +- if (priv->has_phy) { +- phy_disconnect(priv->phydev); +- priv->phydev = NULL; +- } +- + return 0; + } + +@@ -1830,6 +1789,8 @@ static int bcm_enet_probe(struct platfor + + /* MII bus registration */ + if (priv->has_phy) { ++ struct phy_device *phydev; ++ char phy_id[MII_BUS_ID_SIZE + 3]; + + priv->mii_bus = mdiobus_alloc(); + if (!priv->mii_bus) { +@@ -1867,6 +1828,38 @@ static int bcm_enet_probe(struct platfor + dev_err(&pdev->dev, "unable to register mdio bus\n"); + goto out_free_mdio; + } ++ ++ /* connect to PHY */ ++ snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, ++ priv->mii_bus->id, priv->phy_id); ++ ++ phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, ++ PHY_INTERFACE_MODE_MII); ++ ++ if (IS_ERR(phydev)) { ++ dev_err(&pdev->dev, "could not attach to PHY\n"); ++ goto out_unregister_mdio; ++ } ++ ++ /* mask with MAC supported features */ ++ phydev->supported &= (SUPPORTED_10baseT_Half | ++ SUPPORTED_10baseT_Full | ++ SUPPORTED_100baseT_Half | ++ SUPPORTED_100baseT_Full | ++ SUPPORTED_Autoneg | ++ SUPPORTED_Pause | ++ SUPPORTED_MII); ++ phydev->advertising = phydev->supported; ++ ++ if (priv->pause_auto && priv->pause_rx && priv->pause_tx) ++ phydev->advertising |= SUPPORTED_Pause; ++ else ++ phydev->advertising &= ~SUPPORTED_Pause; ++ ++ dev_info(&pdev->dev, "attached PHY at address %d [%s]\n", ++ phydev->addr, phydev->drv->name); ++ ++ priv->phydev = phydev; + } else { + + /* run platform code to initialize PHY device */ +@@ -1912,6 +1905,9 @@ static int bcm_enet_probe(struct platfor + return 0; + + out_unregister_mdio: ++ if (priv->phydev) ++ phy_disconnect(priv->phydev); ++ + if (priv->mii_bus) + mdiobus_unregister(priv->mii_bus); + +@@ -1953,6 +1949,8 @@ static int bcm_enet_remove(struct platfo + enet_writel(priv, 0, ENET_MIISC_REG); + + if (priv->has_phy) { ++ phy_disconnect(priv->phydev); ++ priv->phydev = NULL; + mdiobus_unregister(priv->mii_bus); + mdiobus_free(priv->mii_bus); + } else { diff --git a/target/linux/brcm63xx/patches-3.18/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch b/target/linux/brcm63xx/patches-3.18/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch new file mode 100644 index 0000000000..0a97b25bcd --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/408-bcm63xx_enet-enable-rgmii-clock-on-external-ports.patch @@ -0,0 +1,53 @@ +From d8237d704fc25eb2fc25ef4403608b78c6a6d4be Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Sun, 15 Jul 2012 20:08:57 +0200 +Subject: [PATCH 54/81] bcm63xx_enet: enable rgmii clock on external ports + +--- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 13 +++++++++++++ + drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++++++++ + 2 files changed, 25 insertions(+), 0 deletions(-) + +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -967,6 +967,19 @@ + #define ENETSW_PORTOV_FDX_MASK (1 << 1) + #define ENETSW_PORTOV_LINKUP_MASK (1 << 0) + ++/* Port RGMII control register */ ++#define ENETSW_RGMII_CTRL_REG(x) (0x60 + (x)) ++#define ENETSW_RGMII_CTRL_GMII_CLK_EN (1 << 7) ++#define ENETSW_RGMII_CTRL_MII_OVERRIDE_EN (1 << 6) ++#define ENETSW_RGMII_CTRL_MII_MODE_MASK (3 << 4) ++#define ENETSW_RGMII_CTRL_RGMII_MODE (0 << 4) ++#define ENETSW_RGMII_CTRL_MII_MODE (1 << 4) ++#define ENETSW_RGMII_CTRL_RVMII_MODE (2 << 4) ++#define ENETSW_RGMII_CTRL_TIMING_SEL_EN (1 << 0) ++ ++/* Port RGMII timing register */ ++#define ENETSW_RGMII_TIMING_REG(x) (0x68 + (x)) ++ + /* MDIO control register */ + #define ENETSW_MDIOC_REG (0xb0) + #define ENETSW_MDIOC_EXT_MASK (1 << 16) +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c +@@ -2224,6 +2224,18 @@ static int bcm_enetsw_open(struct net_de + priv->sw_port_link[i] = 0; + } + ++ /* enable external ports */ ++ for (i = ENETSW_RGMII_PORT0; i < priv->num_ports; i++) { ++ u8 rgmii_ctrl; ++ ++ if (!priv->used_ports[i].used) ++ continue; ++ ++ rgmii_ctrl = enetsw_readb(priv, ENETSW_RGMII_CTRL_REG(i)); ++ rgmii_ctrl |= ENETSW_RGMII_CTRL_GMII_CLK_EN; ++ enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); ++ } ++ + /* reset mib */ + val = enetsw_readb(priv, ENETSW_GMCR_REG); + val |= ENETSW_GMCR_RST_MIB_MASK; diff --git a/target/linux/brcm63xx/patches-3.18/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch b/target/linux/brcm63xx/patches-3.18/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch new file mode 100644 index 0000000000..24a5888ef5 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/411-MIPS-BCM63XX-Register-SPI-flash-if-present.patch @@ -0,0 +1,133 @@ +From d135d94b3d1fe599d13e7198d5f502912d694c13 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Sun, 3 Jul 2011 15:00:38 +0200 +Subject: [PATCH 29/60] MIPS: BCM63XX: Register SPI flash if present + +Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> +--- + arch/mips/bcm63xx/dev-flash.c | 33 +++++++++++++++++++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 + + 2 files changed, 33 insertions(+), 2 deletions(-) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -16,9 +16,12 @@ + #include <linux/mtd/mtd.h> + #include <linux/mtd/partitions.h> + #include <linux/mtd/physmap.h> ++#include <linux/spi/spi.h> ++#include <linux/spi/flash.h> + + #include <bcm63xx_cpu.h> + #include <bcm63xx_dev_flash.h> ++#include <bcm63xx_dev_hsspi.h> + #include <bcm63xx_regs.h> + #include <bcm63xx_io.h> + +@@ -65,6 +68,21 @@ void __init bcm63xx_flash_force_phys_bas + mtd_resources[0].end = end; + } + ++static struct flash_platform_data bcm63xx_flash_data = { ++ .part_probe_types = bcm63xx_part_types, ++}; ++ ++static struct spi_board_info bcm63xx_spi_flash_info[] = { ++ { ++ .bus_num = 0, ++ .chip_select = 0, ++ .mode = 0, ++ .max_speed_hz = 781000, ++ .modalias = "m25p80", ++ .platform_data = &bcm63xx_flash_data, ++ }, ++}; ++ + static int __init bcm63xx_detect_flash_type(void) + { + u32 val; +@@ -72,9 +90,15 @@ static int __init bcm63xx_detect_flash_t + switch (bcm63xx_get_cpu_id()) { + case BCM6318_CPU_ID: + /* only support serial flash */ ++ bcm63xx_spi_flash_info[0].max_speed_hz = 62500000; + return BCM63XX_FLASH_TYPE_SERIAL; + case BCM6328_CPU_ID: + val = bcm_misc_readl(MISC_STRAPBUS_6328_REG); ++ if (val & STRAPBUS_6328_HSSPI_CLK_FAST) ++ bcm63xx_spi_flash_info[0].max_speed_hz = 33333334; ++ else ++ bcm63xx_spi_flash_info[0].max_speed_hz = 16666667; ++ + if (val & STRAPBUS_6328_BOOT_SEL_SERIAL) + return BCM63XX_FLASH_TYPE_SERIAL; + else +@@ -93,12 +117,20 @@ static int __init bcm63xx_detect_flash_t + return BCM63XX_FLASH_TYPE_SERIAL; + case BCM6362_CPU_ID: + val = bcm_misc_readl(MISC_STRAPBUS_6362_REG); ++ if (val & STRAPBUS_6362_HSSPI_CLK_FAST) ++ bcm63xx_spi_flash_info[0].max_speed_hz = 50000000; ++ else ++ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; ++ + if (val & STRAPBUS_6362_BOOT_SEL_SERIAL) + return BCM63XX_FLASH_TYPE_SERIAL; + else + return BCM63XX_FLASH_TYPE_NAND; + case BCM6368_CPU_ID: + val = bcm_gpio_readl(GPIO_STRAPBUS_REG); ++ if (val & STRAPBUS_6368_SPI_CLK_FAST) ++ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; ++ + switch (val & STRAPBUS_6368_BOOT_SEL_MASK) { + case STRAPBUS_6368_BOOT_SEL_NAND: + return BCM63XX_FLASH_TYPE_NAND; +@@ -109,6 +141,11 @@ static int __init bcm63xx_detect_flash_t + } + case BCM63268_CPU_ID: + val = bcm_misc_readl(MISC_STRAPBUS_63268_REG); ++ if (val & STRAPBUS_63268_HSSPI_CLK_FAST) ++ bcm63xx_spi_flash_info[0].max_speed_hz = 50000000; ++ else ++ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000; ++ + if (val & STRAPBUS_63268_BOOT_SEL_SERIAL) + return BCM63XX_FLASH_TYPE_SERIAL; + else +@@ -181,8 +218,15 @@ int __init bcm63xx_flash_register(void) + + return platform_device_register(&mtd_dev); + case BCM63XX_FLASH_TYPE_SERIAL: +- pr_warn("unsupported serial flash detected\n"); +- return -ENODEV; ++ if (BCMCPU_IS_6318() || BCMCPU_IS_6328() || BCMCPU_IS_6362() || ++ BCMCPU_IS_63268()) ++ bcm63xx_spi_flash_info[0].bus_num = 1; ++ ++ if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) ++ bcm63xx_flash_data.max_transfer_len = SPI_6358_MSG_DATA_SIZE; ++ ++ return spi_register_board_info(bcm63xx_spi_flash_info, ++ ARRAY_SIZE(bcm63xx_spi_flash_info)); + case BCM63XX_FLASH_TYPE_NAND: + pr_warn("unsupported NAND flash detected\n"); + return -ENODEV; +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h +@@ -708,6 +708,7 @@ + #define GPIO_STRAPBUS_REG 0x40 + #define STRAPBUS_6358_BOOT_SEL_PARALLEL (1 << 1) + #define STRAPBUS_6358_BOOT_SEL_SERIAL (0 << 1) ++#define STRAPBUS_6368_SPI_CLK_FAST (1 << 6) + #define STRAPBUS_6368_BOOT_SEL_MASK 0x3 + #define STRAPBUS_6368_BOOT_SEL_NAND 0 + #define STRAPBUS_6368_BOOT_SEL_SERIAL 1 +@@ -1578,6 +1579,7 @@ + #define IDDQ_CTRL_63268_USBH (1 << 4) + + #define MISC_STRAPBUS_6328_REG 0x240 ++#define STRAPBUS_6328_HSSPI_CLK_FAST (1 << 4) + #define STRAPBUS_6328_FCVO_SHIFT 7 + #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT) + #define STRAPBUS_6328_BOOT_SEL_SERIAL (1 << 28) diff --git a/target/linux/brcm63xx/patches-3.18/412-MTD-physmap-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.18/412-MTD-physmap-allow-passing-pp_data.patch new file mode 100644 index 0000000000..3511120468 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/412-MTD-physmap-allow-passing-pp_data.patch @@ -0,0 +1,41 @@ +From 266c506f4b262bd6aba0776a03d82c98e65d9906 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Tue, 1 May 2012 17:32:36 +0200 +Subject: [PATCH 63/79] MTD: physmap: allow passing pp_data + +--- + drivers/mtd/maps/physmap.c | 4 +++- + include/linux/mtd/physmap.h | 1 + + 2 files changed, 4 insertions(+), 1 deletion(-) + +--- a/drivers/mtd/maps/physmap.c ++++ b/drivers/mtd/maps/physmap.c +@@ -96,6 +96,7 @@ static int physmap_flash_probe(struct pl + { + struct physmap_flash_data *physmap_data; + struct physmap_flash_info *info; ++ struct mtd_part_parser_data *pp_data; + const char * const *probe_type; + const char * const *part_types; + int err = 0; +@@ -187,8 +188,9 @@ static int physmap_flash_probe(struct pl + spin_lock_init(&info->vpp_lock); + + part_types = physmap_data->part_probe_types ? : part_probe_types; ++ pp_data = physmap_data->pp_data ? physmap_data->pp_data : NULL; + +- mtd_device_parse_register(info->cmtd, part_types, NULL, ++ mtd_device_parse_register(info->cmtd, part_types, pp_data, + physmap_data->parts, physmap_data->nr_parts); + return 0; + +--- a/include/linux/mtd/physmap.h ++++ b/include/linux/mtd/physmap.h +@@ -31,6 +31,7 @@ struct physmap_flash_data { + char *probe_type; + struct mtd_partition *parts; + const char * const *part_probe_types; ++ struct mtd_part_parser_data *pp_data; + }; + + #endif /* __LINUX_MTD_PHYSMAP__ */ diff --git a/target/linux/brcm63xx/patches-3.18/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch b/target/linux/brcm63xx/patches-3.18/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch new file mode 100644 index 0000000000..bcb92a1893 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/413-BCM63XX-allow-providing-fixup-data-in-board-data.patch @@ -0,0 +1,72 @@ +From 8879e209111192c5e9752d7bd203cf7582693328 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Thu, 3 May 2012 14:40:03 +0200 +Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 9 ++++++++- + arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 10 ++++++++++ + 2 files changed, 18 insertions(+), 1 deletion(-) + +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -36,6 +36,7 @@ + #include <bcm63xx_dev_usb_ohci.h> + #include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> ++#include <pci_ath9k_fixup.h> + + #include "board_common.h" + +@@ -196,6 +197,7 @@ int __init board_register_devices(void) + int button_count = 0; + int led_count = 0; + int usbh_ports = 0; ++ int i; + + #if CONFIG_OF + if (of_have_populated_dt()) { +@@ -293,6 +295,10 @@ int __init board_register_devices(void) + platform_device_register(&bcm63xx_gpio_keys_device); + } + ++ /* register any fixups */ ++ for (i = 0; i < board.has_caldata; i++) ++ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); ++ + return 0; + } + +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -9,6 +9,7 @@ + #include <bcm63xx_dev_usb_usbd.h> + #include <bcm63xx_dev_dsp.h> + #include <bcm63xx_fallback_sprom.h> ++#include <pci_ath9k_fixup.h> + + /* + * flash mapping +@@ -16,6 +17,11 @@ + #define BCM963XX_CFE_VERSION_OFFSET 0x570 + #define BCM963XX_NVRAM_OFFSET 0x580 + ++struct ath9k_caldata { ++ unsigned int slot; ++ u32 caldata_offset; ++}; ++ + /* + * board definition + */ +@@ -36,6 +42,10 @@ struct board_info { + unsigned int has_uart0:1; + unsigned int has_uart1:1; + unsigned int use_fallback_sprom:1; ++ unsigned int has_caldata:2; ++ ++ /* wifi calibration data config */ ++ struct ath9k_caldata caldata[2]; + + /* ethernet config */ + struct bcm63xx_enet_platform_data enet0; diff --git a/target/linux/brcm63xx/patches-3.18/414-MTD-m25p80-allow-passing-pp_data.patch b/target/linux/brcm63xx/patches-3.18/414-MTD-m25p80-allow-passing-pp_data.patch new file mode 100644 index 0000000000..b7bf57f697 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/414-MTD-m25p80-allow-passing-pp_data.patch @@ -0,0 +1,40 @@ +From 7f17dfe9009beb07a3de0e380932a725293829df Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Tue, 1 May 2012 17:33:03 +0200 +Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data + +--- + drivers/mtd/devices/m25p80.c | 3 +++ + include/linux/spi/flash.h | 2 ++ + 2 files changed, 5 insertions(+) + +--- a/drivers/mtd/devices/m25p80.c ++++ b/drivers/mtd/devices/m25p80.c +@@ -267,6 +267,9 @@ static int m25p_probe(struct spi_device + if (data) + flash->max_transfer_len = data->max_transfer_len; + ++ if (data && data->pp_data) ++ memcpy(&ppdata, data->pp_data, sizeof(ppdata)); ++ + ret = spi_nor_scan(nor, flash_name, mode); + if (ret) + return ret; +--- a/include/linux/spi/flash.h ++++ b/include/linux/spi/flash.h +@@ -12,6 +12,7 @@ struct mtd_part_parser_data; + * with chips that can't be queried for JEDEC or other IDs + * @part_probe_types: optional list of MTD parser names to use for + * partitioning ++ * @pp_data: optional partition parser data. + * + * @max_transfer_len: option maximum read/write length limitation for + * SPI controllers not able to transfer any length commands. +@@ -30,6 +31,7 @@ struct flash_platform_data { + char *type; + + const char **part_probe_types; ++ struct mtd_part_parser_data *pp_data; + + unsigned int max_transfer_len; + /* we'll likely add more ... use JEDEC IDs, etc */ diff --git a/target/linux/brcm63xx/patches-3.18/415-MIPS-BCM63XX-export-the-attached-flash-type.patch b/target/linux/brcm63xx/patches-3.18/415-MIPS-BCM63XX-export-the-attached-flash-type.patch new file mode 100644 index 0000000000..55639cafab --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/415-MIPS-BCM63XX-export-the-attached-flash-type.patch @@ -0,0 +1,31 @@ +From 066f1e37742ee434496d32a41a9284458de96742 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Mon, 13 Jan 2014 12:12:30 +0100 +Subject: [PATCH] MIPS: BCM63XX: export the attached flash type + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + arch/mips/bcm63xx/dev-flash.c | 5 +++++ + arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 ++ + 2 files changed, 7 insertions(+) + +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -236,3 +236,8 @@ int __init bcm63xx_flash_register(void) + return -ENODEV; + } + } ++ ++int bcm63xx_flash_get_type(void) ++{ ++ return flash_type; ++} +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h +@@ -13,4 +13,6 @@ void bcm63xx_flash_force_phys_base_addre + + int __init bcm63xx_flash_register(void); + ++int bcm63xx_flash_get_type(void); ++ + #endif /* __BCM63XX_FLASH_H */ diff --git a/target/linux/brcm63xx/patches-3.18/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch b/target/linux/brcm63xx/patches-3.18/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch new file mode 100644 index 0000000000..7a7c8258d7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/416-BCM63XX-add-a-fixup-for-ath9k-devices.patch @@ -0,0 +1,236 @@ +From bbebbf735a02b6d044ed928978ab4bd5f1833364 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Thu, 3 May 2012 14:36:11 +0200 +Subject: [PATCH 61/72] BCM63XX: add a fixup for ath9k devices + +--- + arch/mips/bcm63xx/Makefile | 3 +- + arch/mips/bcm63xx/pci-ath9k-fixup.c | 190 ++++++++++++++++++++ + .../include/asm/mach-bcm63xx/pci_ath9k_fixup.h | 7 + + 3 files changed, 199 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/bcm63xx/pci-ath9k-fixup.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ + dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ +- usb-common.o sprom.o ++ pci-ath9k-fixup.o usb-common.o sprom.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- /dev/null ++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c +@@ -0,0 +1,199 @@ ++/* ++ * Broadcom BCM63XX Ath9k EEPROM fixup helper. ++ * ++ * Copytight (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> ++ * ++ * Based on ++ * ++ * Atheros AP94 reference board PCI initialization ++ * ++ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org> ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#include <linux/pci.h> ++#include <linux/delay.h> ++#include <linux/ath9k_platform.h> ++ ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_nvram.h> ++#include <bcm63xx_dev_pci.h> ++#include <bcm63xx_dev_flash.h> ++#include <bcm63xx_dev_hsspi.h> ++#include <pci_ath9k_fixup.h> ++ ++#define bcm_hsspi_writel(v, o) bcm_rset_writel(RSET_HSSPI, (v), (o)) ++ ++struct ath9k_fixup { ++ unsigned slot; ++ u8 mac[ETH_ALEN]; ++ struct ath9k_platform_data pdata; ++}; ++ ++static int ath9k_num_fixups; ++static struct ath9k_fixup ath9k_fixups[2] = { ++ { ++ .slot = 255, ++ .pdata = { ++ .led_pin = -1, ++ }, ++ }, ++ { ++ .slot = 255, ++ .pdata = { ++ .led_pin = -1, ++ }, ++ }, ++}; ++ ++static u16 *bcm63xx_read_eeprom(u16 *eeprom, u32 offset) ++{ ++ u32 addr; ++ ++ if (BCMCPU_IS_6328()) { ++ addr = 0x18000000; ++ } else { ++ addr = bcm_mpi_readl(MPI_CSBASE_REG(0)); ++ addr &= MPI_CSBASE_BASE_MASK; ++ } ++ ++ switch (bcm63xx_flash_get_type()) { ++ case BCM63XX_FLASH_TYPE_PARALLEL: ++ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); ++ return eeprom; ++ case BCM63XX_FLASH_TYPE_SERIAL: ++ /* the first megabyte is memory mapped */ ++ if (offset < 0x100000) { ++ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); ++ return eeprom; ++ } ++ ++ if (BCMCPU_IS_6328()) { ++ /* we can change the memory mapped megabyte */ ++ bcm_hsspi_writel(offset & 0xf00000, 0x18); ++ memcpy(eeprom, (void *)KSEG1ADDR(addr + (offset & 0xfffff)), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16)); ++ bcm_hsspi_writel(0, 0x18); ++ return eeprom; ++ } ++ /* can't do anything here without talking to the SPI controller. */ ++ case BCM63XX_FLASH_TYPE_NAND: ++ default: ++ return NULL; ++ } ++} ++ ++static void ath9k_pci_fixup(struct pci_dev *dev) ++{ ++ void __iomem *mem; ++ struct ath9k_platform_data *pdata = NULL; ++ struct pci_dev *bridge = pci_upstream_bridge(dev); ++ u16 *cal_data = NULL; ++ u16 cmd; ++ u32 bar0; ++ u32 val; ++ unsigned i; ++ ++ for (i = 0; i < ath9k_num_fixups; i++) { ++ if (ath9k_fixups[i].slot != PCI_SLOT(dev->devfn)) ++ continue; ++ ++ cal_data = ath9k_fixups[i].pdata.eeprom_data; ++ pdata = &ath9k_fixups[i].pdata; ++ break; ++ } ++ ++ if (cal_data == NULL) ++ return; ++ ++ if (*cal_data != 0xa55a) { ++ pr_err("pci %s: invalid calibration data\n", pci_name(dev)); ++ return; ++ } ++ ++ pr_info("pci %s: fixup device configuration\n", pci_name(dev)); ++ ++ switch (bcm63xx_get_cpu_id()) { ++ case BCM6328_CPU_ID: ++ val = BCM_PCIE_MEM_BASE_PA_6328; ++ break; ++ case BCM6348_CPU_ID: ++ case BCM6358_CPU_ID: ++ case BCM6368_CPU_ID: ++ val = BCM_PCI_MEM_BASE_PA; ++ break; ++ default: ++ BUG(); ++ } ++ ++ mem = ioremap(val, 0x10000); ++ if (!mem) { ++ pr_err("pci %s: ioremap error\n", pci_name(dev)); ++ return; ++ } ++ ++ if (bridge) ++ pci_enable_device(bridge); ++ ++ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); ++ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0); ++ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, val); ++ ++ pci_read_config_word(dev, PCI_COMMAND, &cmd); ++ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY; ++ pci_write_config_word(dev, PCI_COMMAND, cmd); ++ ++ /* set offset to first reg address */ ++ cal_data += 3; ++ while(*cal_data != 0xffff) { ++ u32 reg; ++ reg = *cal_data++; ++ val = *cal_data++; ++ val |= (*cal_data++) << 16; ++ ++ writel(val, mem + reg); ++ udelay(100); ++ } ++ ++ pci_read_config_dword(dev, PCI_VENDOR_ID, &val); ++ dev->vendor = val & 0xffff; ++ dev->device = (val >> 16) & 0xffff; ++ ++ pci_read_config_dword(dev, PCI_CLASS_REVISION, &val); ++ dev->revision = val & 0xff; ++ dev->class = val >> 8; /* upper 3 bytes */ ++ ++ pci_read_config_word(dev, PCI_COMMAND, &cmd); ++ cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY); ++ pci_write_config_word(dev, PCI_COMMAND, cmd); ++ ++ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0); ++ ++ if (bridge) ++ pci_disable_device(bridge); ++ ++ iounmap(mem); ++ ++ dev->dev.platform_data = pdata; ++} ++DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); ++ ++void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) ++{ ++ if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) ++ return; ++ ++ ath9k_fixups[ath9k_num_fixups].slot = slot; ++ ++ if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) ++ return; ++ ++ if (bcm63xx_nvram_get_mac_address(ath9k_fixups[ath9k_num_fixups].mac)) ++ return; ++ ++ ath9k_fixups[ath9k_num_fixups].pdata.macaddr = ath9k_fixups[ath9k_num_fixups].mac; ++ ath9k_num_fixups++; ++} +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h +@@ -0,0 +1,7 @@ ++#ifndef _PCI_ATH9K_FIXUP ++#define _PCI_ATH9K_FIXUP ++ ++ ++void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; ++ ++#endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.18/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch b/target/linux/brcm63xx/patches-3.18/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch new file mode 100644 index 0000000000..3b02c072cd --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/417-MTD-bcm63xxpart-allow-passing-a-caldata-offset.patch @@ -0,0 +1,120 @@ +Allow bcm63xxpart to receive a caldata offset if calibration data is +contained in flash. +--- + drivers/mtd/bcm63xxpart.c | 51 ++++++++++++++++++++++++++++++++++++--- + include/linux/mtd/partitions.h | 2 + + 2 files changed, 49 insertions(+), 4 deletions(-) + +--- a/drivers/mtd/bcm63xxpart.c ++++ b/drivers/mtd/bcm63xxpart.c +@@ -53,10 +53,12 @@ static int bcm63xx_parse_cfe_partitions( + struct mtd_partition *parts; + int ret; + size_t retlen; +- unsigned int rootfsaddr, kerneladdr, spareaddr; ++ unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr; + unsigned int rootfslen, kernellen, sparelen, totallen; + unsigned int cfelen, nvramlen; + unsigned int cfe_erasesize; ++ unsigned int caldatalen1 = 0, caldataaddr1 = 0; ++ unsigned int caldatalen2 = 0, caldataaddr2 = 0; + int i; + u32 computed_crc; + bool rootfs_first = false; +@@ -70,6 +72,24 @@ static int bcm63xx_parse_cfe_partitions( + cfelen = cfe_erasesize; + nvramlen = bcm63xx_nvram_get_psi_size() * SZ_1K; + nvramlen = roundup(nvramlen, cfe_erasesize); ++ nvramaddr = master->size - nvramlen; ++ ++ if (data) { ++ if (data->caldata[0]) { ++ caldatalen1 = cfe_erasesize; ++ caldataaddr1 = rounddown(data->caldata[0], ++ cfe_erasesize); ++ } ++ if (data->caldata[1]) { ++ caldatalen2 = cfe_erasesize; ++ caldataaddr2 = rounddown(data->caldata[1], ++ cfe_erasesize); ++ } ++ if (caldataaddr1 == caldataaddr2) { ++ caldataaddr2 = 0; ++ caldatalen2 = 0; ++ } ++ } + + /* Allocate memory for buffer */ + buf = vmalloc(sizeof(struct bcm_tag)); +@@ -121,7 +141,7 @@ static int bcm63xx_parse_cfe_partitions( + rootfsaddr = 0; + spareaddr = cfelen; + } +- sparelen = master->size - spareaddr - nvramlen; ++ sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr; + + /* Determine number of partitions */ + if (rootfslen > 0) +@@ -130,6 +150,12 @@ static int bcm63xx_parse_cfe_partitions( + if (kernellen > 0) + nrparts++; + ++ if (caldatalen1 > 0) ++ nrparts++; ++ ++ if (caldatalen2 > 0) ++ nrparts++; ++ + /* Ask kernel for more memory */ + parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL); + if (!parts) { +@@ -167,15 +193,32 @@ static int bcm63xx_parse_cfe_partitions( + curpart++; + } + ++ if (caldatalen1 > 0) { ++ if (caldatalen2 > 0) ++ parts[curpart].name = "cal_data1"; ++ else ++ parts[curpart].name = "cal_data"; ++ parts[curpart].offset = caldataaddr1; ++ parts[curpart].size = caldatalen1; ++ curpart++; ++ } ++ ++ if (caldatalen2 > 0) { ++ parts[curpart].name = "cal_data2"; ++ parts[curpart].offset = caldataaddr2; ++ parts[curpart].size = caldatalen2; ++ curpart++; ++ } ++ + parts[curpart].name = "nvram"; +- parts[curpart].offset = master->size - nvramlen; ++ parts[curpart].offset = nvramaddr; + parts[curpart].size = nvramlen; + curpart++; + + /* Global partition "linux" to make easy firmware upgrade */ + parts[curpart].name = "linux"; + parts[curpart].offset = cfelen; +- parts[curpart].size = master->size - cfelen - nvramlen; ++ parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen; + + for (i = 0; i < nrparts; i++) + pr_info("Partition %d is %s offset %llx and length %llx\n", i, +--- a/include/linux/mtd/partitions.h ++++ b/include/linux/mtd/partitions.h +@@ -56,10 +56,12 @@ struct device_node; + /** + * struct mtd_part_parser_data - used to pass data to MTD partition parsers. + * @origin: for RedBoot, start address of MTD device ++ * @caldata: for CFE, start address of wifi calibration data + * @of_node: for OF parsers, device node containing partitioning information + */ + struct mtd_part_parser_data { + unsigned long origin; ++ unsigned long caldata[2]; + struct device_node *of_node; + }; + diff --git a/target/linux/brcm63xx/patches-3.18/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch b/target/linux/brcm63xx/patches-3.18/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch new file mode 100644 index 0000000000..fdcfa19e5e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/418-MIPS-BCM63XX-pass-caldata-info-to-flash.patch @@ -0,0 +1,83 @@ +From 977f8a30103b9c4992cab8f49357fe0d4274004f Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Thu, 3 May 2012 14:55:26 +0200 +Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash + +--- + arch/mips/bcm63xx/boards/board_common.c | 2 +- + arch/mips/bcm63xx/dev-flash.c | 9 ++++++++- + arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 4 +++- + 3 files changed, 12 insertions(+), 3 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -267,7 +267,7 @@ int __init board_register_devices(void) + if (board.num_spis) + spi_register_board_info(board.spis, board.num_spis); + +- bcm63xx_flash_register(); ++ bcm63xx_flash_register(board.has_caldata, board.caldata); + + /* count number of LEDs defined by this device */ + while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name) +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -37,12 +37,15 @@ static struct mtd_partition mtd_partitio + } + }; + ++static struct mtd_part_parser_data bcm63xx_parser_data; ++ + static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL }; + + static struct physmap_flash_data flash_data = { + .width = 2, + .parts = mtd_partitions, + .part_probe_types = bcm63xx_part_types, ++ .pp_data = &bcm63xx_parser_data, + }; + + static struct resource mtd_resources[] = { +@@ -70,6 +73,7 @@ void __init bcm63xx_flash_force_phys_bas + + static struct flash_platform_data bcm63xx_flash_data = { + .part_probe_types = bcm63xx_part_types, ++ .pp_data = &bcm63xx_parser_data, + }; + + static struct spi_board_info bcm63xx_spi_flash_info[] = { +@@ -197,9 +201,13 @@ void __init bcm63xx_flash_detect(void) + } + } + +-int __init bcm63xx_flash_register(void) ++int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) + { + u32 val; ++ unsigned int i; ++ ++ for (i = 0; i < num_caldata; i++) ++ bcm63xx_parser_data.caldata[i] = caldata[i].caldata_offset; + + switch (flash_type) { + case BCM63XX_FLASH_TYPE_PARALLEL: +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h +@@ -1,6 +1,8 @@ + #ifndef __BCM63XX_FLASH_H + #define __BCM63XX_FLASH_H + ++#include <board_bcm963xx.h> ++ + enum { + BCM63XX_FLASH_TYPE_PARALLEL, + BCM63XX_FLASH_TYPE_SERIAL, +@@ -11,7 +13,7 @@ void bcm63xx_flash_detect(void); + + void bcm63xx_flash_force_phys_base_address(u32 start, u32 end); + +-int __init bcm63xx_flash_register(void); ++int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); + + int bcm63xx_flash_get_type(void); + diff --git a/target/linux/brcm63xx/patches-3.18/420-BCM63XX-add-endian-check-for-ath9k.patch b/target/linux/brcm63xx/patches-3.18/420-BCM63XX-add-endian-check-for-ath9k.patch new file mode 100644 index 0000000000..0e01be15b3 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/420-BCM63XX-add-endian-check-for-ath9k.patch @@ -0,0 +1,51 @@ +--- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h ++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h +@@ -2,6 +2,7 @@ + #define _PCI_ATH9K_FIXUP + + +-void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init; ++void pci_enable_ath9k_fixup(unsigned slot, u32 offset, ++ unsigned endian_check) __init; + + #endif /* _PCI_ATH9K_FIXUP */ +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -20,6 +20,7 @@ + struct ath9k_caldata { + unsigned int slot; + u32 caldata_offset; ++ unsigned int endian_check:1; + }; + + /* +--- a/arch/mips/bcm63xx/pci-ath9k-fixup.c ++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c +@@ -181,12 +181,14 @@ static void ath9k_pci_fixup(struct pci_d + } + DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); + +-void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset) ++void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, ++ unsigned endian_check) + { + if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) + return; + + ath9k_fixups[ath9k_num_fixups].slot = slot; ++ ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; + + if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) + return; +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -297,7 +297,8 @@ int __init board_register_devices(void) + + /* register any fixups */ + for (i = 0; i < board.has_caldata; i++) +- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset); ++ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, ++ board.caldata[i].endian_check); + + return 0; + } diff --git a/target/linux/brcm63xx/patches-3.18/421-BCM63XX-add-led-pin-for-ath9k.patch b/target/linux/brcm63xx/patches-3.18/421-BCM63XX-add-led-pin-for-ath9k.patch new file mode 100644 index 0000000000..27ea83f3cc --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/421-BCM63XX-add-led-pin-for-ath9k.patch @@ -0,0 +1,49 @@ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -298,7 +298,7 @@ int __init board_register_devices(void) + /* register any fixups */ + for (i = 0; i < board.has_caldata; i++) + pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, +- board.caldata[i].endian_check); ++ board.caldata[i].endian_check, board.caldata[i].led_pin); + + return 0; + } +--- a/arch/mips/bcm63xx/pci-ath9k-fixup.c ++++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c +@@ -182,13 +182,14 @@ static void ath9k_pci_fixup(struct pci_d + DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup); + + void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset, +- unsigned endian_check) ++ unsigned endian_check, int led_pin) + { + if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups)) + return; + + ath9k_fixups[ath9k_num_fixups].slot = slot; + ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check; ++ ath9k_fixups[ath9k_num_fixups].pdata.led_pin = led_pin; + + if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset)) + return; +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -21,6 +21,7 @@ struct ath9k_caldata { + unsigned int slot; + u32 caldata_offset; + unsigned int endian_check:1; ++ int led_pin; + }; + + /* +--- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h ++++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h +@@ -3,6 +3,6 @@ + + + void pci_enable_ath9k_fixup(unsigned slot, u32 offset, +- unsigned endian_check) __init; ++ unsigned endian_check, int led_pin) __init; + + #endif /* _PCI_ATH9K_FIXUP */ diff --git a/target/linux/brcm63xx/patches-3.18/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch b/target/linux/brcm63xx/patches-3.18/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch new file mode 100644 index 0000000000..c07bd32e2a --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/422-BCM63XX-add-a-fixup-for-rt2x00-devices.patch @@ -0,0 +1,206 @@ +From 5ed5b5e9614fa5b02da699ab565af76c7e63d64d Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Mon, 7 Jan 2013 17:45:39 +0100 +Subject: [PATCH 72/72] 446-BCM63XX-add-a-fixup-for-rt2x00-devices + +--- + arch/mips/bcm63xx/Makefile | 2 +- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 17 ++++- + arch/mips/bcm63xx/dev-flash.c | 2 +- + arch/mips/bcm63xx/pci-rt2x00-fixup.c | 71 ++++++++++++++++++++ + .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 +- + .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 9 ++- + .../include/asm/mach-bcm63xx/pci_rt2x00_fixup.h | 9 +++ + 7 files changed, 104 insertions(+), 8 deletions(-) + create mode 100644 arch/mips/bcm63xx/pci-rt2x00-fixup.c + create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h + +--- a/arch/mips/bcm63xx/Makefile ++++ b/arch/mips/bcm63xx/Makefile +@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o + setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \ + dev-pcmcia.o dev-rng.o dev-spi.o dev-hsspi.o dev-uart.o \ + dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \ +- pci-ath9k-fixup.o usb-common.o sprom.o ++ pci-ath9k-fixup.o pci-rt2x00-fixup.o usb-common.o sprom.o + obj-$(CONFIG_EARLY_PRINTK) += early_printk.o + + obj-y += boards/ +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -37,6 +37,7 @@ + #include <bcm63xx_dev_usb_usbd.h> + #include <board_bcm963xx.h> + #include <pci_ath9k_fixup.h> ++#include <pci_rt2x00_fixup.h> + + #include "board_common.h" + +@@ -296,9 +297,19 @@ int __init board_register_devices(void) + } + + /* register any fixups */ +- for (i = 0; i < board.has_caldata; i++) +- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset, +- board.caldata[i].endian_check, board.caldata[i].led_pin); ++ for (i = 0; i < board.has_caldata; i++) { ++ switch (board.caldata[i].vendor) { ++ case PCI_VENDOR_ID_ATHEROS: ++ pci_enable_ath9k_fixup(board.caldata[i].slot, ++ board.caldata[i].caldata_offset, board.caldata[i].endian_check, ++ board.caldata[i].led_pin); ++ break; ++ case PCI_VENDOR_ID_RALINK: ++ pci_enable_rt2x00_fixup(board.caldata[i].slot, ++ board.caldata[i].eeprom); ++ break; ++ } ++ } + + return 0; + } +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -201,7 +201,7 @@ void __init bcm63xx_flash_detect(void) + } + } + +-int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata) ++int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata) + { + u32 val; + unsigned int i; +--- /dev/null ++++ b/arch/mips/bcm63xx/pci-rt2x00-fixup.c +@@ -0,0 +1,72 @@ ++/* ++ * Broadcom BCM63XX RT2x00 EEPROM fixup helper. ++ * ++ * Copyright (C) 2012 Álvaro Fernández Rojas <noltari@gmail.com> ++ * ++ * Based on ++ * ++ * Broadcom BCM63XX Ath9k EEPROM fixup helper. ++ * ++ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com> ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#include <linux/if_ether.h> ++#include <linux/pci.h> ++#include <linux/platform_device.h> ++#include <linux/rt2x00_platform.h> ++ ++#include <bcm63xx_nvram.h> ++#include <pci_rt2x00_fixup.h> ++ ++struct rt2x00_fixup { ++ unsigned slot; ++ u8 mac[ETH_ALEN]; ++ struct rt2x00_platform_data pdata; ++}; ++ ++static int rt2x00_num_fixups; ++static struct rt2x00_fixup rt2x00_fixups[2] = { ++ { ++ .slot = 255, ++ }, ++ { ++ .slot = 255, ++ }, ++}; ++ ++static void rt2x00_pci_fixup(struct pci_dev *dev) ++{ ++ unsigned i; ++ struct rt2x00_platform_data *pdata = NULL; ++ ++ for (i = 0; i < rt2x00_num_fixups; i++) { ++ if (rt2x00_fixups[i].slot != PCI_SLOT(dev->devfn)) ++ continue; ++ ++ pdata = &rt2x00_fixups[i].pdata; ++ break; ++ } ++ ++ dev->dev.platform_data = pdata; ++} ++DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_RALINK, PCI_ANY_ID, rt2x00_pci_fixup); ++ ++void __init pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) ++{ ++ if (rt2x00_num_fixups >= ARRAY_SIZE(rt2x00_fixups)) ++ return; ++ ++ rt2x00_fixups[rt2x00_num_fixups].slot = slot; ++ rt2x00_fixups[rt2x00_num_fixups].pdata.eeprom_file_name = kstrdup(eeprom, GFP_KERNEL); ++ ++ if (bcm63xx_nvram_get_mac_address(rt2x00_fixups[rt2x00_num_fixups].mac)) ++ return; ++ ++ rt2x00_fixups[rt2x00_num_fixups].pdata.mac_address = rt2x00_fixups[rt2x00_num_fixups].mac; ++ rt2x00_num_fixups++; ++} ++ +--- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h ++++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h +@@ -13,7 +13,7 @@ void bcm63xx_flash_detect(void); + + void bcm63xx_flash_force_phys_base_address(u32 start, u32 end); + +-int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata); ++int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata); + + int bcm63xx_flash_get_type(void); + +--- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h ++++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h +@@ -10,6 +10,7 @@ + #include <bcm63xx_dev_dsp.h> + #include <bcm63xx_fallback_sprom.h> + #include <pci_ath9k_fixup.h> ++#include <pci_rt2x00_fixup.h> + + /* + * flash mapping +@@ -17,11 +18,15 @@ + #define BCM963XX_CFE_VERSION_OFFSET 0x570 + #define BCM963XX_NVRAM_OFFSET 0x580 + +-struct ath9k_caldata { ++struct bcm63xx_caldata { ++ unsigned int vendor; + unsigned int slot; + u32 caldata_offset; ++ /* Atheros */ + unsigned int endian_check:1; + int led_pin; ++ /* Ralink */ ++ char* eeprom; + }; + + /* +@@ -47,7 +52,7 @@ struct board_info { + unsigned int has_caldata:2; + + /* wifi calibration data config */ +- struct ath9k_caldata caldata[2]; ++ struct bcm63xx_caldata caldata[2]; + + /* ethernet config */ + struct bcm63xx_enet_platform_data enet0; +--- /dev/null ++++ b/arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h +@@ -0,0 +1,9 @@ ++#ifndef _PCI_RT2X00_FIXUP ++#define _PCI_RT2X00_FIXUP ++ ++#define PCI_VENDOR_ID_RALINK 0x1814 ++ ++void pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) __init; ++ ++#endif /* _PCI_RT2X00_FIXUP */ ++ diff --git a/target/linux/brcm63xx/patches-3.18/423-bcm63xx_enet_add_b53_support.patch b/target/linux/brcm63xx/patches-3.18/423-bcm63xx_enet_add_b53_support.patch new file mode 100644 index 0000000000..469a365b91 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/423-bcm63xx_enet_add_b53_support.patch @@ -0,0 +1,169 @@ +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h +@@ -336,6 +336,9 @@ struct bcm_enet_priv { + struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT]; + int sw_port_link[ENETSW_MAX_PORT]; + ++ /* platform device for associated switch */ ++ struct platform_device *b53_device; ++ + /* used to poll switch port state */ + struct timer_list swphy_poll; + spinlock_t enetsw_mdio_lock; +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c +@@ -30,6 +30,7 @@ + #include <linux/dma-mapping.h> + #include <linux/platform_device.h> + #include <linux/if_vlan.h> ++#include <linux/platform_data/b53.h> + + #include <bcm63xx_dev_enet.h> + #include "bcm63xx_enet.h" +@@ -1974,7 +1975,8 @@ static int bcm_enet_remove(struct platfo + return 0; + } + +-struct platform_driver bcm63xx_enet_driver = { ++ ++static struct platform_driver bcm63xx_enet_driver = { + .probe = bcm_enet_probe, + .remove = bcm_enet_remove, + .driver = { +@@ -1983,6 +1985,42 @@ struct platform_driver bcm63xx_enet_driv + }, + }; + ++struct b53_platform_data bcm63xx_b53_pdata = { ++ .chip_id = 0x6300, ++ .big_endian = 1, ++}; ++ ++struct platform_device bcm63xx_b53_dev = { ++ .name = "b53-switch", ++ .id = -1, ++ .dev = { ++ .platform_data = &bcm63xx_b53_pdata, ++ }, ++}; ++ ++static int bcmenet_switch_register(struct bcm_enet_priv *priv, u16 port_mask) ++{ ++ int ret; ++ ++ bcm63xx_b53_pdata.regs = priv->base; ++ bcm63xx_b53_pdata.enabled_ports = port_mask; ++ bcm63xx_b53_pdata.alias = priv->net_dev->name; ++ ++ ret = platform_device_register(&bcm63xx_b53_dev); ++ if (!ret) ++ priv->b53_device = &bcm63xx_b53_dev; ++ ++ return ret; ++} ++ ++static void bcmenet_switch_unregister(struct bcm_enet_priv *priv) ++{ ++ if (priv->b53_device) ++ platform_device_unregister(&bcm63xx_b53_dev); ++ ++ priv->b53_device = NULL; ++} ++ + /* + * switch mii access callbacks + */ +@@ -2236,29 +2274,6 @@ static int bcm_enetsw_open(struct net_de + enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i)); + } + +- /* reset mib */ +- val = enetsw_readb(priv, ENETSW_GMCR_REG); +- val |= ENETSW_GMCR_RST_MIB_MASK; +- enetsw_writeb(priv, val, ENETSW_GMCR_REG); +- mdelay(1); +- val &= ~ENETSW_GMCR_RST_MIB_MASK; +- enetsw_writeb(priv, val, ENETSW_GMCR_REG); +- mdelay(1); +- +- /* force CPU port state */ +- val = enetsw_readb(priv, ENETSW_IMPOV_REG); +- val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; +- enetsw_writeb(priv, val, ENETSW_IMPOV_REG); +- +- /* enable switch forward engine */ +- val = enetsw_readb(priv, ENETSW_SWMODE_REG); +- val |= ENETSW_SWMODE_FWD_EN_MASK; +- enetsw_writeb(priv, val, ENETSW_SWMODE_REG); +- +- /* enable jumbo on all ports */ +- enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); +- enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); +- + /* initialize flow control buffer allocation */ + enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, + ENETDMA_BUFALLOC_REG(priv->rx_chan)); +@@ -2718,6 +2733,9 @@ static int bcm_enetsw_probe(struct platf + struct bcm63xx_enetsw_platform_data *pd; + struct resource *res_mem; + int ret, irq_rx, irq_tx; ++ unsigned i, num_ports = 0; ++ u16 port_mask = BIT(8); ++ u8 val; + + /* stop if shared driver failed, assume driver->probe will be + * called in the same order we register devices (correct ?) +@@ -2807,6 +2825,43 @@ static int bcm_enetsw_probe(struct platf + priv->pdev = pdev; + priv->net_dev = dev; + ++ /* reset mib */ ++ val = enetsw_readb(priv, ENETSW_GMCR_REG); ++ val |= ENETSW_GMCR_RST_MIB_MASK; ++ enetsw_writeb(priv, val, ENETSW_GMCR_REG); ++ mdelay(1); ++ val &= ~ENETSW_GMCR_RST_MIB_MASK; ++ enetsw_writeb(priv, val, ENETSW_GMCR_REG); ++ mdelay(1); ++ ++ /* force CPU port state */ ++ val = enetsw_readb(priv, ENETSW_IMPOV_REG); ++ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK; ++ enetsw_writeb(priv, val, ENETSW_IMPOV_REG); ++ ++ /* enable switch forward engine */ ++ val = enetsw_readb(priv, ENETSW_SWMODE_REG); ++ val |= ENETSW_SWMODE_FWD_EN_MASK; ++ enetsw_writeb(priv, val, ENETSW_SWMODE_REG); ++ ++ /* enable jumbo on all ports */ ++ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG); ++ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG); ++ ++ for (i = 0; i < priv->num_ports; i++) { ++ struct bcm63xx_enetsw_port *port = &priv->used_ports[i]; ++ ++ if (!port->used) ++ continue; ++ ++ num_ports++; ++ port_mask |= BIT(i); ++ } ++ ++ /* only register if there is more than one external port */ ++ if (num_ports > 1) ++ bcmenet_switch_register(priv, port_mask); ++ + return 0; + + out_put_clk: +@@ -2835,6 +2890,9 @@ static int bcm_enetsw_remove(struct plat + priv = netdev_priv(dev); + unregister_netdev(dev); + ++ /* remove switch */ ++ bcmenet_switch_unregister(priv); ++ + /* release device resources */ + iounmap(priv->base); + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); diff --git a/target/linux/brcm63xx/patches-3.18/424-bcm63xx_enet_no_request_mem_region.patch b/target/linux/brcm63xx/patches-3.18/424-bcm63xx_enet_no_request_mem_region.patch new file mode 100644 index 0000000000..12e366c99c --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/424-bcm63xx_enet_no_request_mem_region.patch @@ -0,0 +1,15 @@ +--- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c ++++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c +@@ -2780,12 +2780,6 @@ static int bcm_enetsw_probe(struct platf + if (ret) + goto out; + +- if (!request_mem_region(res_mem->start, resource_size(res_mem), +- "bcm63xx_enetsw")) { +- ret = -EBUSY; +- goto out; +- } +- + priv->base = ioremap(res_mem->start, resource_size(res_mem)); + if (priv->base == NULL) { + ret = -ENOMEM; diff --git a/target/linux/brcm63xx/patches-3.18/425-bcm63xxpart_parse_paritions_from_dt.patch b/target/linux/brcm63xx/patches-3.18/425-bcm63xxpart_parse_paritions_from_dt.patch new file mode 100644 index 0000000000..dd0ba7054d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/425-bcm63xxpart_parse_paritions_from_dt.patch @@ -0,0 +1,349 @@ +--- a/drivers/mtd/bcm63xxpart.c ++++ b/drivers/mtd/bcm63xxpart.c +@@ -32,6 +32,7 @@ + #include <linux/vmalloc.h> + #include <linux/mtd/mtd.h> + #include <linux/mtd/partitions.h> ++#include <linux/of.h> + + #include <asm/mach-bcm63xx/bcm63xx_nvram.h> + #include <linux/bcm963xx_tag.h> +@@ -43,66 +44,35 @@ + + #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0 + +-static int bcm63xx_parse_cfe_partitions(struct mtd_info *master, +- struct mtd_partition **pparts, +- struct mtd_part_parser_data *data) ++static bool node_has_compatible(struct device_node *pp) ++{ ++ return of_get_property(pp, "compatible", NULL); ++} ++ ++static int parse_bcmtag(struct mtd_info *master, struct mtd_partition *pparts, ++ int next_part, size_t offset, size_t size) + { +- /* CFE, NVRAM and global Linux are always present */ +- int nrparts = 3, curpart = 0; + struct bcm_tag *buf; +- struct mtd_partition *parts; ++ u32 computed_crc; + int ret; + size_t retlen; +- unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr; +- unsigned int rootfslen, kernellen, sparelen, totallen; +- unsigned int cfelen, nvramlen; +- unsigned int cfe_erasesize; +- unsigned int caldatalen1 = 0, caldataaddr1 = 0; +- unsigned int caldatalen2 = 0, caldataaddr2 = 0; +- int i; +- u32 computed_crc; ++ unsigned int rootfsaddr, kerneladdr; ++ unsigned int rootfslen, kernellen, totallen; + bool rootfs_first = false; +- +- if (!bcm63xx_is_cfe_present()) +- return -EINVAL; +- +- cfe_erasesize = max_t(uint32_t, master->erasesize, +- BCM63XX_CFE_BLOCK_SIZE); +- +- cfelen = cfe_erasesize; +- nvramlen = bcm63xx_nvram_get_psi_size() * SZ_1K; +- nvramlen = roundup(nvramlen, cfe_erasesize); +- nvramaddr = master->size - nvramlen; +- +- if (data) { +- if (data->caldata[0]) { +- caldatalen1 = cfe_erasesize; +- caldataaddr1 = rounddown(data->caldata[0], +- cfe_erasesize); +- } +- if (data->caldata[1]) { +- caldatalen2 = cfe_erasesize; +- caldataaddr2 = rounddown(data->caldata[1], +- cfe_erasesize); +- } +- if (caldataaddr1 == caldataaddr2) { +- caldataaddr2 = 0; +- caldatalen2 = 0; +- } +- } ++ int curr_part = next_part; + + /* Allocate memory for buffer */ +- buf = vmalloc(sizeof(struct bcm_tag)); ++ buf = vmalloc(sizeof(*buf)); + if (!buf) + return -ENOMEM; + + /* Get the tag */ +- ret = mtd_read(master, cfelen, sizeof(struct bcm_tag), &retlen, ++ ret = mtd_read(master, offset, sizeof(*buf), &retlen, + (void *)buf); + +- if (retlen != sizeof(struct bcm_tag)) { ++ if (retlen != sizeof(*buf)) { + vfree(buf); +- return -EIO; ++ return 0; + } + + computed_crc = crc32_le(IMAGETAG_CRC_START, (u8 *)buf, +@@ -121,7 +91,6 @@ static int bcm63xx_parse_cfe_partitions( + + kerneladdr = kerneladdr - BCM63XX_EXTENDED_SIZE; + rootfsaddr = rootfsaddr - BCM63XX_EXTENDED_SIZE; +- spareaddr = roundup(totallen, master->erasesize) + cfelen; + + if (rootfsaddr < kerneladdr) { + /* default Broadcom layout */ +@@ -130,8 +99,8 @@ static int bcm63xx_parse_cfe_partitions( + } else { + /* OpenWrt layout */ + rootfsaddr = kerneladdr + kernellen; +- rootfslen = buf->real_rootfs_length; +- spareaddr = rootfsaddr + rootfslen; ++ rootfslen = size - kernellen - ++ sizeof(*buf); + } + } else { + pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n", +@@ -139,16 +108,145 @@ static int bcm63xx_parse_cfe_partitions( + kernellen = 0; + rootfslen = 0; + rootfsaddr = 0; +- spareaddr = cfelen; + } +- sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr; + +- /* Determine number of partitions */ +- if (rootfslen > 0) +- nrparts++; ++ if (kernellen > 0) { ++ int kernelpart = curr_part; + +- if (kernellen > 0) +- nrparts++; ++ if (rootfslen > 0 && rootfs_first) ++ kernelpart++; ++ pparts[kernelpart].name = "kernel"; ++ pparts[kernelpart].offset = kerneladdr; ++ pparts[kernelpart].size = kernellen; ++ curr_part++; ++ } ++ ++ if (rootfslen > 0) { ++ int rootfspart = curr_part; ++ ++ if (kernellen > 0 && rootfs_first) ++ rootfspart--; ++ pparts[rootfspart].name = "rootfs"; ++ pparts[rootfspart].offset = rootfsaddr; ++ pparts[rootfspart].size = rootfslen; ++ ++ curr_part++; ++ } ++ ++ vfree(buf); ++ ++ return curr_part - next_part; ++} ++ ++ ++static int bcm63xx_parse_cfe_partitions_of(struct mtd_info *master, ++ struct mtd_partition **pparts, ++ struct mtd_part_parser_data *data) ++{ ++ struct device_node *dp = data->of_node; ++ struct device_node *pp; ++ int i, nr_parts = 0; ++ const char *partname; ++ int len; ++ ++ for_each_child_of_node(dp, pp) { ++ if (node_has_compatible(pp)) ++ continue; ++ ++ nr_parts++; ++ } ++ ++ *pparts = kzalloc(nr_parts * sizeof(**pparts), GFP_KERNEL); ++ if (!*pparts) ++ return -ENOMEM; ++ ++ i = 0; ++ for_each_child_of_node(dp, pp) { ++ const __be32 *reg; ++ int a_cells, s_cells; ++ size_t size, offset; ++ ++ if (node_has_compatible(pp)) ++ continue; ++ ++ reg = of_get_property(pp, "reg", &len); ++ if (!reg) { ++ nr_parts--; ++ continue; ++ } ++ ++ a_cells = of_n_addr_cells(pp); ++ s_cells = of_n_size_cells(pp); ++ offset = of_read_number(reg, a_cells); ++ size = of_read_number(reg + a_cells, s_cells); ++ partname = of_get_property(pp, "label", &len); ++ if (!partname) ++ partname = of_get_property(pp, "name", &len); ++ ++ if (!strcmp(partname, "linux")) ++ i += parse_bcmtag(master, *pparts, i, offset, size); ++ ++ if (of_get_property(pp, "read-only", &len)) ++ (*pparts)[i].mask_flags |= MTD_WRITEABLE; ++ ++ if (of_get_property(pp, "lock", &len)) ++ (*pparts)[i].mask_flags |= MTD_POWERUP_LOCK; ++ ++ (*pparts)[i].offset = offset; ++ (*pparts)[i].size = size; ++ (*pparts)[i].name = partname; ++ ++ i++; ++ } ++ ++ return i; ++} ++ ++static int bcm63xx_parse_cfe_partitions(struct mtd_info *master, ++ struct mtd_partition **pparts, ++ struct mtd_part_parser_data *data) ++{ ++ /* CFE, NVRAM and global Linux are always present */ ++ int nrparts = 5, curpart = 0; ++ struct mtd_partition *parts; ++ unsigned int nvramaddr; ++ unsigned int cfelen, nvramlen; ++ unsigned int cfe_erasesize; ++ unsigned int caldatalen1 = 0, caldataaddr1 = 0; ++ unsigned int caldatalen2 = 0, caldataaddr2 = 0; ++ unsigned int imageaddr, imagelen; ++ int i; ++ ++ if (!bcm63xx_is_cfe_present()) ++ return -EINVAL; ++ ++ cfe_erasesize = max_t(uint32_t, master->erasesize, ++ BCM63XX_CFE_BLOCK_SIZE); ++ ++ cfelen = cfe_erasesize; ++ nvramlen = bcm63xx_nvram_get_psi_size() * SZ_1K; ++ nvramlen = roundup(nvramlen, cfe_erasesize); ++ nvramaddr = master->size - nvramlen; ++ ++ if (data) { ++ if (data->caldata[0]) { ++ caldatalen1 = cfe_erasesize; ++ caldataaddr1 = rounddown(data->caldata[0], ++ cfe_erasesize); ++ } ++ if (data->caldata[1]) { ++ caldatalen2 = cfe_erasesize; ++ caldataaddr2 = rounddown(data->caldata[1], ++ cfe_erasesize); ++ } ++ if (caldataaddr1 == caldataaddr2) { ++ caldataaddr2 = 0; ++ caldatalen2 = 0; ++ } ++ } ++ ++ imageaddr = cfelen; ++ imagelen = min_not_zero(nvramaddr, caldataaddr1) - imageaddr; + + if (caldatalen1 > 0) + nrparts++; +@@ -158,10 +256,8 @@ static int bcm63xx_parse_cfe_partitions( + + /* Ask kernel for more memory */ + parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL); +- if (!parts) { +- vfree(buf); ++ if (!parts) + return -ENOMEM; +- } + + /* Start building partition list */ + parts[curpart].name = "CFE"; +@@ -169,29 +265,7 @@ static int bcm63xx_parse_cfe_partitions( + parts[curpart].size = cfelen; + curpart++; + +- if (kernellen > 0) { +- int kernelpart = curpart; +- +- if (rootfslen > 0 && rootfs_first) +- kernelpart++; +- parts[kernelpart].name = "kernel"; +- parts[kernelpart].offset = kerneladdr; +- parts[kernelpart].size = kernellen; +- curpart++; +- } +- +- if (rootfslen > 0) { +- int rootfspart = curpart; +- +- if (kernellen > 0 && rootfs_first) +- rootfspart--; +- parts[rootfspart].name = "rootfs"; +- parts[rootfspart].offset = rootfsaddr; +- parts[rootfspart].size = rootfslen; +- if (sparelen > 0 && !rootfs_first) +- parts[rootfspart].size += sparelen; +- curpart++; +- } ++ curpart += parse_bcmtag(master, parts, curpart, imageaddr, imagelen); + + if (caldatalen1 > 0) { + if (caldatalen2 > 0) +@@ -217,25 +291,33 @@ static int bcm63xx_parse_cfe_partitions( + + /* Global partition "linux" to make easy firmware upgrade */ + parts[curpart].name = "linux"; +- parts[curpart].offset = cfelen; +- parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen; ++ parts[curpart].offset = imageaddr; ++ parts[curpart].size = imagelen; ++ curpart++; + +- for (i = 0; i < nrparts; i++) ++ for (i = 0; i < curpart; i++) + pr_info("Partition %d is %s offset %llx and length %llx\n", i, + parts[i].name, parts[i].offset, parts[i].size); + +- pr_info("Spare partition is offset %x and length %x\n", spareaddr, +- sparelen); +- + *pparts = parts; +- vfree(buf); + + return nrparts; + }; + ++ ++static int bcm63xx_parse_partitions(struct mtd_info *master, ++ struct mtd_partition **pparts, ++ struct mtd_part_parser_data *data) ++{ ++ if (data && data->of_node) ++ return bcm63xx_parse_cfe_partitions_of(master, pparts, data); ++ else ++ return bcm63xx_parse_cfe_partitions(master, pparts, data); ++} ++ + static struct mtd_part_parser bcm63xx_cfe_parser = { + .owner = THIS_MODULE, +- .parse_fn = bcm63xx_parse_cfe_partitions, ++ .parse_fn = bcm63xx_parse_partitions, + .name = "bcm63xxpart", + }; + diff --git a/target/linux/brcm63xx/patches-3.18/499-allow_better_context_for_board_patches.patch b/target/linux/brcm63xx/patches-3.18/499-allow_better_context_for_board_patches.patch new file mode 100644 index 0000000000..5dcfa9dda6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/499-allow_better_context_for_board_patches.patch @@ -0,0 +1,56 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -61,7 +61,7 @@ static struct board_info __initdata boar + .ephy_reset_gpio = 36, + .ephy_reset_gpio_flags = GPIOF_INIT_HIGH, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_3368 */ + + /* + * known 6328 boards +@@ -110,7 +110,7 @@ static struct board_info __initdata boar + }, + }, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_6328 */ + + /* + * known 6338 boards +@@ -199,7 +199,7 @@ static struct board_info __initdata boar + }, + }, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_6338 */ + + /* + * known 6345 boards +@@ -211,7 +211,7 @@ static struct board_info __initdata boar + + .has_uart0 = 1, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_6345 */ + + /* + * known 6348 boards +@@ -544,7 +544,7 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_6348 */ + + /* + * known 6358 boards +@@ -697,7 +697,7 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + }; +-#endif ++#endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* + * all boards diff --git a/target/linux/brcm63xx/patches-3.18/500-board-D4PW.patch b/target/linux/brcm63xx/patches-3.18/500-board-D4PW.patch new file mode 100644 index 0000000000..b54a3e5443 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/500-board-D4PW.patch @@ -0,0 +1,67 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -544,6 +544,56 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + }; ++ ++static struct board_info __initdata board_96348_D4PW = { ++ .name = "D-4P-W", ++ .expected_cpu_id = 0x6348, ++ ++ .has_enet1 = 1, ++ .has_pci = 1, ++ .has_uart0 = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "D-4P-W:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "D-4P-W::status", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "D-4P-W:green:internet", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "D-4P-W:red:internet", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 7, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6348 */ + + /* +@@ -725,6 +775,7 @@ static const struct board_info __initcon + &board_DV201AMR, + &board_96348gw_a, + &board_rta1025w_16, ++ &board_96348_D4PW, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.18/501-board-NB4.patch b/target/linux/brcm63xx/patches-3.18/501-board-NB4.patch new file mode 100644 index 0000000000..e900f0f8d3 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/501-board-NB4.patch @@ -0,0 +1,315 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -12,6 +12,12 @@ + #include <linux/string.h> + #include <linux/gpio_keys.h> + #include <linux/input.h> ++#include <linux/platform_device.h> ++#include <linux/spi/spi.h> ++#include <linux/spi/spi_gpio.h> ++#if 0 /* FIXME: 3.14 removed non-DT support */ ++#include <linux/spi/74x164.h> ++#endif + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +@@ -31,6 +37,12 @@ + #define BCM963XX_KEYS_POLL_INTERVAL 20 + #define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3) + ++#define NB4_PID_OFFSET 0xff80 ++#define NB4_74X164_GPIO_BASE 64 ++#define NB4_SPI_GPIO_MOSI 7 ++#define NB4_SPI_GPIO_CLK 6 ++#define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) ++ + /* + * known 3368 boards + */ +@@ -747,6 +759,268 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + }; ++ ++struct spi_gpio_platform_data nb4_spi_gpio_data = { ++ .sck = NB4_SPI_GPIO_CLK, ++ .mosi = NB4_SPI_GPIO_MOSI, ++ .miso = SPI_GPIO_NO_MISO, ++ .num_chipselect = 1, ++}; ++ ++ ++static struct platform_device nb4_spi_gpio = { ++ .name = "spi_gpio", ++ .id = 1, ++ .dev = { ++ .platform_data = &nb4_spi_gpio_data, ++ }, ++}; ++ ++static struct platform_device * __initdata nb4_devices[] = { ++ &nb4_spi_gpio, ++}; ++ ++#if 0 /* FIXME: 3.14 removed non-DT support */ ++const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = { ++ .base = NB4_74X164_GPIO_BASE ++}; ++#endif ++ ++static struct spi_board_info nb4_spi_devices[] = { ++#if 0 /* FIXME: 3.14 removed non-DT support */ ++ { ++ .modalias = "74x164", ++ .max_speed_hz = 781000, ++ .bus_num = 1, ++ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, ++ .mode = SPI_MODE_0, ++ .platform_data = &nb4_74x164_platform_data ++ } ++#endif ++}; ++ ++static struct board_info __initdata board_nb4_ser_r0 = { ++ .name = "NB4-SER-r0", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .leds = { ++ { ++ .name = "NB4-SER-r0:white:adsl", ++ .gpio = NB4_74HC64_GPIO(4), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:white:traffic", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:white:tel", ++ .gpio = NB4_74HC64_GPIO(3), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:white:tv", ++ .gpio = NB4_74HC64_GPIO(2), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:white:wifi", ++ .gpio = 15, ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:white:alarm", ++ .gpio = NB4_74HC64_GPIO(0), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:red:service", ++ .gpio = 29, ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:green:service", ++ .gpio = 30, ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-SER-r0:blue:service", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 37, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "service", ++ .gpio = 27, ++ .type = EV_KEY, ++ .code = BTN_0, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "clip", ++ .gpio = 31, ++ .type = EV_KEY, ++ .code = BTN_1, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ .devs = nb4_devices, ++ .num_devs = ARRAY_SIZE(nb4_devices), ++ .spis = nb4_spi_devices, ++ .num_spis = ARRAY_SIZE(nb4_spi_devices), ++}; ++ ++static struct board_info __initdata board_nb4_fxc_r1 = { ++ .name = "NB4-FXC-r1", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .leds = { ++ { ++ .name = "NB4-FXC-r1:white:adsl", ++ .gpio = NB4_74HC64_GPIO(4), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-FXC-r1:white:traffic", ++ .gpio = 2, ++ }, ++ { ++ .name = "NB4-FXC-r1:white:tel", ++ .gpio = NB4_74HC64_GPIO(3), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-FXC-r1:white:tv", ++ .gpio = NB4_74HC64_GPIO(2), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-FXC-r1:white:wifi", ++ .gpio = 15, ++ }, ++ { ++ .name = "NB4-FXC-r1:white:alarm", ++ .gpio = NB4_74HC64_GPIO(0), ++ .active_low = 1, ++ }, ++ { ++ .name = "NB4-FXC-r1:red:service", ++ .gpio = 29, ++ }, ++ { ++ .name = "NB4-FXC-r1:green:service", ++ .gpio = 30, ++ }, ++ { ++ .name = "NB4-FXC-r1:blue:service", ++ .gpio = 4, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 37, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "service", ++ .gpio = 27, ++ .type = EV_KEY, ++ .code = BTN_0, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "clip", ++ .gpio = 31, ++ .type = EV_KEY, ++ .code = BTN_1, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ .devs = nb4_devices, ++ .num_devs = ARRAY_SIZE(nb4_devices), ++ .spis = nb4_spi_devices, ++ .num_spis = ARRAY_SIZE(nb4_spi_devices), ++}; + #endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* +@@ -783,6 +1057,8 @@ static const struct board_info __initcon + &board_96358vw2, + &board_AGPFS0, + &board_DWVS0, ++ &board_nb4_ser_r0, ++ &board_nb4_fxc_r1, + #endif + }; + +@@ -819,6 +1095,8 @@ static struct of_device_id const bcm963x + { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m-fwb", .data = &board_DWVS0, }, + { .compatible = "pirelli,agpf-s0", .data = &board_AGPFS0, }, ++ { .compatible = "sfr,nb4-ser-r0", .data = &board_nb4_ser_r0, }, ++ { .compatible = "sfr,nb4-fxc-r1", .data = &board_nb4_fxc_r1, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6368 + #endif diff --git a/target/linux/brcm63xx/patches-3.18/502-board-96338W2_E7T.patch b/target/linux/brcm63xx/patches-3.18/502-board-96338W2_E7T.patch new file mode 100644 index 0000000000..3a8477753a --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/502-board-96338W2_E7T.patch @@ -0,0 +1,51 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -211,6 +211,40 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_96338w2_e7t = { ++ .name = "96338W2_E7T", ++ .expected_cpu_id = 0x6338, ++ ++ .has_enet0 = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "96338W2_E7T:green:ppp", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "96338W2_E7T:green:ppp-fail", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "96338W2_E7T:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6338 */ + + /* +@@ -1036,6 +1070,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6338 + &board_96338gw, + &board_96338w, ++ &board_96338w2_e7t, + #endif + #ifdef CONFIG_BCM63XX_CPU_6345 + &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.18/503-board-CPVA642.patch b/target/linux/brcm63xx/patches-3.18/503-board-CPVA642.patch new file mode 100644 index 0000000000..8b5ad5cb0f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/503-board-CPVA642.patch @@ -0,0 +1,109 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -749,6 +749,98 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_CPVA642 = { ++ .name = "CPVA642", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .leds = { ++ { ++ .name = "CPVA642:red:power", ++ .gpio = 14, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:power", ++ .gpio = 11, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "CPVA642:red:wifi", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:wifi", ++ .gpio = 28, ++ .active_low = 0, ++ }, ++ { ++ .name = "CPVA642:red:link", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:link", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:ether", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:phone1", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:phone2", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA642:green:usb", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 36, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 37, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ ++ + static struct board_info __initdata board_AGPFS0 = { + .name = "AGPF-S0", + .expected_cpu_id = 0x6358, +@@ -1091,6 +1183,7 @@ static const struct board_info __initcon + &board_96358vw, + &board_96358vw2, + &board_AGPFS0, ++ &board_CPVA642, + &board_DWVS0, + &board_nb4_ser_r0, + &board_nb4_fxc_r1, diff --git a/target/linux/brcm63xx/patches-3.18/504-board_dsl_274xb_rev_c.patch b/target/linux/brcm63xx/patches-3.18/504-board_dsl_274xb_rev_c.patch new file mode 100644 index 0000000000..d1433607e6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/504-board_dsl_274xb_rev_c.patch @@ -0,0 +1,80 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -886,6 +886,61 @@ static struct board_info __initdata boar + .has_ohci0 = 1, + }; + ++/* D-Link DSL-274xB revison C2/C3 */ ++static struct board_info __initdata board_dsl_274xb_rev_c = { ++ .name = "AW4139", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "dsl-274xb:green:power", ++ .gpio = 5, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "dsl-274xb:red:power", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:green:adsl", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:green:internet", ++ .gpio = 2, ++ }, ++ { ++ .name = "dsl-274xb:red:internet", ++ .gpio = 10, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + struct spi_gpio_platform_data nb4_spi_gpio_data = { + .sck = NB4_SPI_GPIO_CLK, + .mosi = NB4_SPI_GPIO_MOSI, +@@ -1185,6 +1240,7 @@ static const struct board_info __initcon + &board_AGPFS0, + &board_CPVA642, + &board_DWVS0, ++ &board_dsl_274xb_rev_c, + &board_nb4_ser_r0, + &board_nb4_fxc_r1, + #endif +@@ -1218,6 +1274,7 @@ static struct of_device_id const bcm963x + { .compatible = "alcatel,rg100a", .data = &board_96358vw2, }, + { .compatible = "brcm,bcm96358vw", .data = &board_96358vw, }, + { .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, }, ++ { .compatible = "d-link,dsl-274xb-c2", .data = &board_dsl_274xb_rev_c, }, + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, + { .compatible = "pirelli,a226g", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, diff --git a/target/linux/brcm63xx/patches-3.18/505-board_spw500v.patch b/target/linux/brcm63xx/patches-3.18/505-board_spw500v.patch new file mode 100644 index 0000000000..1d153c85a3 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/505-board_spw500v.patch @@ -0,0 +1,103 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -640,6 +640,84 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct sprom_fixup __initdata spw500v_fixups[] = { ++ { .offset = 46, .value = 0x3046 }, ++ { .offset = 47, .value = 0x15a7 }, ++ { .offset = 48, .value = 0xfa89 }, ++ { .offset = 49, .value = 0xfe79 }, ++ { .offset = 57, .value = 0x6a49 }, ++}; ++ ++static struct board_info __initdata board_spw500v = { ++ .name = "SPW500V", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .has_dsp = 1, ++ .dsp = { ++ .gpio_rst = 6, ++ .gpio_int = 34, ++ .ext_irq = 2, ++ .cs = 2, ++ }, ++ ++ .leds = { ++ { ++ .name = "SPW500V:red:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "SPW500V:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "SPW500V:green:ppp", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { .name = "SPW500V:green:pstn", ++ .gpio = 28, ++ .active_low = 1, ++ }, ++ { ++ .name = "SPW500V:green:voip", ++ .gpio = 32, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ .board_fixups = spw500v_fixups, ++ .num_board_fixups = ARRAY_SIZE(spw500v_fixups), ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6348 */ + + /* +@@ -1232,6 +1310,7 @@ static const struct board_info __initcon + &board_96348gw_a, + &board_rta1025w_16, + &board_96348_D4PW, ++ &board_spw500v, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 +@@ -1269,6 +1348,7 @@ static struct of_device_id const bcm963x + { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, + { .compatible = "sagem,f@st2404", .data = &board_FAST2404, }, ++ { .compatible = "t-com,spw500v", .data = &board_spw500v, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6358 + { .compatible = "alcatel,rg100a", .data = &board_96358vw2, }, diff --git a/target/linux/brcm63xx/patches-3.18/506-board_gw6200_gw6000.patch b/target/linux/brcm63xx/patches-3.18/506-board_gw6200_gw6000.patch new file mode 100644 index 0000000000..27fa19def8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/506-board_gw6200_gw6000.patch @@ -0,0 +1,133 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -503,6 +503,112 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_gw6200 = { ++ .name = "GW6200", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ .enet1 = { ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ ++ .has_dsp = 1, ++ .dsp = { ++ .gpio_rst = 8, /* FIXME: What is real GPIO here? */ ++ .gpio_int = 34, ++ .ext_irq = 2, ++ .cs = 2, ++ }, ++ ++ .leds = { ++ { ++ .name = "GW6200:green:line1", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "GW6200:green:line2", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "GW6200:green:line3", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "GW6200:green:tel", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 36, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ ++static struct board_info __initdata board_gw6000 = { ++ .name = "GW6000", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ .enet1 = { ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ ++ .has_dsp = 1, ++ .dsp = { ++ .gpio_rst = 6, ++ .gpio_int = 34, ++ .ext_irq = 2, ++ .cs = 2, ++ }, ++ ++ /* GW6000 has no GPIO-controlled leds */ ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 36, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ ++ ++ + static struct board_info __initdata board_FAST2404 = { + .name = "F@ST2404", + .expected_cpu_id = 0x6348, +@@ -1303,6 +1409,8 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6348 + &board_96348r, + &board_96348gw, ++ &board_gw6000, ++ &board_gw6200, + &board_96348gw_10, + &board_96348gw_11, + &board_FAST2404, +@@ -1349,6 +1457,8 @@ static struct of_device_id const bcm963x + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, + { .compatible = "sagem,f@st2404", .data = &board_FAST2404, }, + { .compatible = "t-com,spw500v", .data = &board_spw500v, }, ++ { .compatible = "tecom,gw6000", .data = &board_gw6000, }, ++ { .compatible = "tecom,gw6200", .data = &board_gw6200, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6358 + { .compatible = "alcatel,rg100a", .data = &board_96358vw2, }, diff --git a/target/linux/brcm63xx/patches-3.18/507-board-MAGIC.patch b/target/linux/brcm63xx/patches-3.18/507-board-MAGIC.patch new file mode 100644 index 0000000000..c5ce970ae6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/507-board-MAGIC.patch @@ -0,0 +1,89 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -824,6 +824,78 @@ static struct board_info __initdata boar + .num_board_fixups = ARRAY_SIZE(spw500v_fixups), + }, + }; ++ ++static struct board_info __initdata board_96348sv = { ++ .name = "MAGIC", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ .enet1 = { ++ /* it has BP_ENET_EXTERNAL_PHY */ ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ .has_ehci0 = 1, ++ ++ .has_dsp = 1, ++ .dsp = { ++ .gpio_rst = 25, ++ .gpio_int = 34, ++ .cs = 2, ++ .ext_irq = 2, ++ }, ++ ++ .leds = { ++ { ++ .name = "MAGIC:green:voip", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "MAGIC:green:adsl", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "MAGIC:green:wifi", ++ .gpio = 28, ++ }, ++ { ++ .name = "MAGIC:green:usb", ++ .gpio = 35, ++ .active_low = 1, ++ }, ++ { ++ .name = "MAGIC:green:hpna", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "MAGIC:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "MAGIC:green:stop", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6348 */ + + /* +@@ -1419,6 +1491,7 @@ static const struct board_info __initcon + &board_rta1025w_16, + &board_96348_D4PW, + &board_spw500v, ++ &board_96348sv, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.18/508-board_hw553.patch b/target/linux/brcm63xx/patches-3.18/508-board_hw553.patch new file mode 100644 index 0000000000..0dc43c19be --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/508-board_hw553.patch @@ -0,0 +1,102 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1458,6 +1458,83 @@ static struct board_info __initdata boar + .spis = nb4_spi_devices, + .num_spis = ARRAY_SIZE(nb4_spi_devices), + }; ++ ++static struct board_info __initdata board_HW553 = { ++ .name = "HW553", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ ++ .has_enet1 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .leds = { ++ { ++ .name = "HW553:red:adsl", ++ .gpio = 34, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:blue:adsl", ++ .gpio = 35, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:red:lan", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:blue:lan", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:red:power", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:blue:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW553:red:wifi", ++ .gpio = 25, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:red:hspa", ++ .gpio = 12, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW553:blue:hspa", ++ .gpio = 13, ++ .active_low = 1, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* +@@ -1503,6 +1580,7 @@ static const struct board_info __initcon + &board_dsl_274xb_rev_c, + &board_nb4_ser_r0, + &board_nb4_fxc_r1, ++ &board_HW553, + #endif + }; + +@@ -1539,6 +1617,7 @@ static struct of_device_id const bcm963x + { .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, }, + { .compatible = "d-link,dsl-274xb-c2", .data = &board_dsl_274xb_rev_c, }, + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, ++ { .compatible = "huawei,hg553", .data = &board_HW553, }, + { .compatible = "pirelli,a226g", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m-fwb", .data = &board_DWVS0, }, diff --git a/target/linux/brcm63xx/patches-3.18/509-board_rta1320_16m.patch b/target/linux/brcm63xx/patches-3.18/509-board_rta1320_16m.patch new file mode 100644 index 0000000000..2aa9b72b6b --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/509-board_rta1320_16m.patch @@ -0,0 +1,56 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -245,6 +245,45 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_rta1320_16m = { ++ .name = "RTA1320_16M", ++ .expected_cpu_id = 0x6338, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "RTA1320_16M:green:adsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA1320_16M:green:ppp", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA1320_16M:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "RTA1320_16M:green:stop", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6338 */ + + /* +@@ -1551,6 +1590,7 @@ static const struct board_info __initcon + &board_96338gw, + &board_96338w, + &board_96338w2_e7t, ++ &board_rta1320_16m, + #endif + #ifdef CONFIG_BCM63XX_CPU_6345 + &board_96345gw2, diff --git a/target/linux/brcm63xx/patches-3.18/510-board_spw303v.patch b/target/linux/brcm63xx/patches-3.18/510-board_spw303v.patch new file mode 100644 index 0000000000..49564dcae6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/510-board_spw303v.patch @@ -0,0 +1,91 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1574,6 +1574,72 @@ static struct board_info __initdata boar + .pci_dev = 1, + }, + }; ++ ++ /* T-Home Speedport W 303V Typ B */ ++static struct board_info __initdata board_spw303v = { ++ .name = "96358-502V", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "spw303v:green:power+adsl", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "spw303v:red:power+adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "spw303v:green:ppp", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "spw303v:green:ses", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "spw303v:green:voip", ++ .gpio = 27, ++ .active_low = 1, ++ }, ++ { ++ .name = "spw303v:green:pots", ++ .gpio = 31, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 11, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "ses", ++ .gpio = 37, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ } ++}; + #endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* +@@ -1621,6 +1687,7 @@ static const struct board_info __initcon + &board_nb4_ser_r0, + &board_nb4_fxc_r1, + &board_HW553, ++ &board_spw303v, + #endif + }; + +@@ -1664,6 +1731,7 @@ static struct of_device_id const bcm963x + { .compatible = "pirelli,agpf-s0", .data = &board_AGPFS0, }, + { .compatible = "sfr,nb4-ser-r0", .data = &board_nb4_ser_r0, }, + { .compatible = "sfr,nb4-fxc-r1", .data = &board_nb4_fxc_r1, }, ++ { .compatible = "t-com,spw303v", .data = &board_spw303v, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6368 + #endif diff --git a/target/linux/brcm63xx/patches-3.18/511-board_V2500V.patch b/target/linux/brcm63xx/patches-3.18/511-board_V2500V.patch new file mode 100644 index 0000000000..a918728ef2 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/511-board_V2500V.patch @@ -0,0 +1,123 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -935,6 +935,65 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_V2500V_BB = { ++ .name = "V2500V_BB", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "V2500V_BB:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "V2500V_BB:red:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "V2500V_BB:green:adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { .name = "V2500V_BB:green:ppp", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "V2500V_BB:green:wireless", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 31, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6348 */ + + /* +@@ -1675,6 +1734,7 @@ static const struct board_info __initcon + &board_96348_D4PW, + &board_spw500v, + &board_96348sv, ++ &board_V2500V_BB, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 +@@ -1765,6 +1825,22 @@ void __init board_bcm963xx_init(void) + val &= MPI_CSBASE_BASE_MASK; + } + boot_addr = (u8 *)KSEG1ADDR(val); ++ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr); ++ ++ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */ ++ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/ ++ /* Loading firmware from the CFE Prompt always loads to Bank 0 */ ++ /* Do an early check of CFE and then select bank 0 */ ++ ++ if (boot_addr == (u8 *)0xbf800000) { ++ u8 *tmp_boot_addr = (u8*)0xbfc00000; ++ ++ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET); ++ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) { ++ printk(KERN_INFO PFX "V2500V: nvram bank 0\n"); ++ boot_addr = tmp_boot_addr; ++ } ++ } + + /* dump cfe version */ + cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET; +--- a/arch/mips/bcm63xx/dev-flash.c ++++ b/arch/mips/bcm63xx/dev-flash.c +@@ -19,6 +19,7 @@ + #include <linux/spi/spi.h> + #include <linux/spi/flash.h> + ++#include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> + #include <bcm63xx_dev_flash.h> + #include <bcm63xx_dev_hsspi.h> +@@ -220,6 +221,13 @@ int __init bcm63xx_flash_register(int nu + val = bcm_mpi_readl(MPI_CSBASE_REG(0)); + val &= MPI_CSBASE_BASE_MASK; + ++ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */ ++ /* Loading from CFE always uses Bank 0 */ ++ if (!strcmp(board_get_name(), "V2500V_BB")) { ++ pr_info("V2500V: Start in Bank 0\n"); ++ val = val + 0x400000; // Select Bank 0 start address ++ } ++ + mtd_resources[0].start = val; + mtd_resources[0].end = 0x1FFFFFFF; + } diff --git a/target/linux/brcm63xx/patches-3.18/512-board_BTV2110.patch b/target/linux/brcm63xx/patches-3.18/512-board_BTV2110.patch new file mode 100644 index 0000000000..0d29b074e8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/512-board_BTV2110.patch @@ -0,0 +1,75 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -473,6 +473,64 @@ static struct board_info __initdata boar + }, + }; + ++ ++/* BT Voyager 2110 */ ++static struct board_info __initdata board_V2110 = { ++ .name = "V2110", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "V2110:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "V2110:red:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "V2110:green:adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { .name = "V2110:green:ppp", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "V2110:green:wireless", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ ++ + static struct board_info __initdata board_96348gw = { + .name = "96348GW", + .expected_cpu_id = 0x6348, +@@ -1735,6 +1793,7 @@ static const struct board_info __initcon + &board_spw500v, + &board_96348sv, + &board_V2500V_BB, ++ &board_V2110, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.18/513-MIPS-BCM63XX-add-inventel-Livebox-support.patch b/target/linux/brcm63xx/patches-3.18/513-MIPS-BCM63XX-add-inventel-Livebox-support.patch new file mode 100644 index 0000000000..2f7bf49ca8 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/513-MIPS-BCM63XX-add-inventel-Livebox-support.patch @@ -0,0 +1,260 @@ +From 7e6b22225e16fbb22dbf7f2113d8c6d65333818c Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 9 Mar 2014 04:55:52 +0100 +Subject: [PATCH 44/44] MIPS: BCM63XX: add inventel Livebox support + +--- + arch/mips/bcm63xx/boards/Kconfig | 6 + + arch/mips/bcm63xx/boards/Makefile | 1 + + arch/mips/bcm63xx/boards/board_common.c | 2 +- + arch/mips/bcm63xx/boards/board_common.h | 6 + + arch/mips/bcm63xx/boards/board_livebox.c | 193 +++++++++++++++++++++++++++++++ + 5 files changed, 207 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/bcm63xx/boards/board_livebox.c + +--- a/arch/mips/bcm63xx/boards/Kconfig ++++ b/arch/mips/bcm63xx/boards/Kconfig +@@ -12,4 +12,10 @@ config BOARD_BCM963XX + default y + help + ++config BOARD_LIVEBOX ++ bool "Inventel Livebox(es) boards" ++ select SSB ++ help ++ Inventel Livebox boards using the RedBoot bootloader. ++ + endmenu +--- a/arch/mips/bcm63xx/boards/Makefile ++++ b/arch/mips/bcm63xx/boards/Makefile +@@ -1,2 +1,3 @@ + obj-y += board_common.o + obj-$(CONFIG_BOARD_BCM963XX) += board_bcm963xx.o ++obj-$(CONFIG_BOARD_LIVEBOX) += board_livebox.o +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -61,7 +61,7 @@ void __init board_prom_init(void) + if (fw_arg3 == CFE_EPTSEAL) + board_bcm963xx_init(); + else +- panic("unsupported bootloader detected"); ++ board_livebox_init(); + } + + static int (*board_get_mac_address)(u8 mac[ETH_ALEN]); +--- a/arch/mips/bcm63xx/boards/board_common.h ++++ b/arch/mips/bcm63xx/boards/board_common.h +@@ -24,4 +24,10 @@ static inline void board_of_device_prese + } + #endif + ++#if defined(CONFIG_BOARD_LIVEBOX) ++void board_livebox_init(void); ++#else ++static inline void board_livebox_init(void) { } ++#endif ++ + #endif /* __BOARD_COMMON_H */ +--- /dev/null ++++ b/arch/mips/bcm63xx/boards/board_livebox.c +@@ -0,0 +1,200 @@ ++/* ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file "COPYING" in the main directory of this archive ++ * for more details. ++ * ++ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org> ++ */ ++ ++#include <linux/init.h> ++#include <linux/kernel.h> ++#include <linux/string.h> ++#include <linux/input.h> ++#include <asm/addrspace.h> ++#include <bcm63xx_board.h> ++#include <bcm63xx_cpu.h> ++#include <bcm63xx_regs.h> ++#include <bcm63xx_io.h> ++#include <bcm63xx_dev_flash.h> ++#include <board_bcm963xx.h> ++ ++#include "board_common.h" ++ ++#define PFX "board_livebox: " ++ ++#define LIVEBOX_KEYS_POLL_INTERVAL 20 ++#define LIVEBOX_KEYS_DEBOUNCE_INTERVAL (LIVEBOX_KEYS_POLL_INTERVAL * 3) ++ ++static unsigned int mac_addr_used = 0; ++ ++/* ++ * known 6348 boards ++ */ ++#ifdef CONFIG_BCM63XX_CPU_6348 ++static struct board_info __initdata board_livebox_blue5g = { ++ .name = "Livebox-blue-5g", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 31, ++ }, ++ ++ .ephy_reset_gpio = 6, ++ .ephy_reset_gpio_flags = GPIOF_INIT_HIGH, ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ ++ .has_dsp = 0, /*TODO some Liveboxes have dsp*/ ++ .dsp = { ++ .gpio_rst = 6, ++ .gpio_int = 35, ++ .cs = 2, ++ .ext_irq = 2, ++ }, ++ ++ .leds = { ++ { ++ .name = "Livebox-blue-5g:red:adsl-fail", ++ .gpio = 0, ++ .active_low = 0, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "Livebox-blue-5g:red:adsl", ++ .gpio = 1, ++ }, ++ { ++ .name = "Livebox-blue-5g:red:traffic", ++ .gpio = 2, ++ }, ++ { ++ .name = "Livebox-blue-5g:red:phone", ++ .gpio = 3, ++ }, ++ { ++ .name = "Livebox-blue-5g:red:wifi", ++ .gpio = 4, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "BTN_1", ++ .gpio = 36, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = BTN_1, ++ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "BTN_2", ++ .gpio = 7, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = BTN_2, ++ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ ++ }, ++ ++ .ephy_reset_gpio = 6, ++ .ephy_reset_gpio_flags = GPIOF_INIT_HIGH, ++}; ++#endif ++ ++/* ++ * all boards ++ */ ++static const struct board_info __initdata *bcm963xx_boards[] = { ++#ifdef CONFIG_BCM63XX_CPU_6348 ++ &board_livebox_blue5g ++#endif ++}; ++ ++/* ++ * register & return a new board mac address ++ */ ++static int livebox_get_mac_address(u8 *mac) ++{ ++ u8 *p; ++ int count; ++ ++ memcpy(mac, (u8 *)0xBEBFF377, ETH_ALEN); ++ ++ p = mac + ETH_ALEN - 1; ++ count = mac_addr_used; ++ ++ while (count--) { ++ do { ++ (*p)++; ++ if (*p != 0) ++ break; ++ p--; ++ } while (p != mac); ++ } ++ ++ if (p == mac) { ++ printk(KERN_ERR PFX "unable to fetch mac address\n"); ++ return -ENODEV; ++ } ++ mac_addr_used++; ++ ++ return 0; ++} ++ ++/* ++ * early init callback ++ */ ++#define LIVEBOX_GPIO_DETECT_MASK 0x000000ff ++#define LIVEBOX_BOOT_ADDR 0x1e400000 ++ ++#define LIVEBOX_HW_BLUE5G_9 0x90 ++ ++void __init board_livebox_init(void) ++{ ++ u32 val; ++ u8 hw_version; ++ const struct board_info *board; ++ ++ /* Get hardware version */ ++ val = bcm_gpio_readl(GPIO_CTL_LO_REG); ++ val &= ~LIVEBOX_GPIO_DETECT_MASK; ++ bcm_gpio_writel(val, GPIO_CTL_LO_REG); ++ ++ hw_version = bcm_gpio_readl(GPIO_DATA_LO_REG) & LIVEBOX_GPIO_DETECT_MASK; ++ switch (hw_version) { ++ case LIVEBOX_HW_BLUE5G_9: ++ printk(KERN_INFO PFX "Livebox BLUE5G.9\n"); ++ board = bcm963xx_boards[0]; ++ break; ++ default: ++ printk(KERN_INFO PFX "Unknown livebox version: %02x\n", hw_version); ++ /* use default livebox configuration */ ++ board = bcm963xx_boards[0]; ++ break; ++ } ++ ++ /* use default livebox configuration */ ++ board_early_setup(board, livebox_get_mac_address); ++ ++ /* read base address of boot chip select (0) */ ++ val = bcm_mpi_readl(MPI_CSBASE_REG(0)); ++ val &= MPI_CSBASE_BASE_MASK; ++ if (val != LIVEBOX_BOOT_ADDR) { ++ printk(KERN_NOTICE PFX "flash address is: 0x%08x, forcing to: 0x%08x\n", ++ val, LIVEBOX_BOOT_ADDR); ++ bcm63xx_flash_force_phys_base_address(LIVEBOX_BOOT_ADDR, 0x1ebfffff); ++ } ++} diff --git a/target/linux/brcm63xx/patches-3.18/514-board_ct536_ct5621.patch b/target/linux/brcm63xx/patches-3.18/514-board_ct536_ct5621.patch new file mode 100644 index 0000000000..4c44094d43 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/514-board_ct536_ct5621.patch @@ -0,0 +1,78 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -531,6 +531,58 @@ static struct board_info __initdata boar + }; + + ++static struct board_info __initdata board_ct536_ct5621 = { ++ .name = "CT536_CT5621", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 0, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ .has_ehci0 = 1, ++ ++ .leds = { ++ { ++ .name = "CT536_CT5621:green:adsl-fail", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "CT536_CT5621:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++}; ++ + static struct board_info __initdata board_96348gw = { + .name = "96348GW", + .expected_cpu_id = 0x6348, +@@ -1794,6 +1846,7 @@ static const struct board_info __initcon + &board_96348sv, + &board_V2500V_BB, + &board_V2110, ++ &board_ct536_ct5621, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 +@@ -1830,6 +1883,8 @@ static struct of_device_id const bcm963x + { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, }, + { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, }, + { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, }, ++ { .compatible = "comtrend,ct-536+", .data = &board_ct536_ct5621, }, ++ { .compatible = "comtrend,ct-5621", .data = &board_ct536_ct5621, }, + { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, + { .compatible = "sagem,f@st2404", .data = &board_FAST2404, }, diff --git a/target/linux/brcm63xx/patches-3.18/515-board_DWV-S0_fixes.patch b/target/linux/brcm63xx/patches-3.18/515-board_DWV-S0_fixes.patch new file mode 100644 index 0000000000..278cf2c536 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/515-board_DWV-S0_fixes.patch @@ -0,0 +1,19 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1332,6 +1332,8 @@ static struct board_info __initdata boar + .name = "DWV-S0", + .expected_cpu_id = 0x6358, + ++ .has_uart0 = 1, ++ + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, +@@ -1348,6 +1350,7 @@ static struct board_info __initdata boar + }, + + .has_ohci0 = 1, ++ .has_ehci0 = 1, + }; + + /* D-Link DSL-274xB revison C2/C3 */ diff --git a/target/linux/brcm63xx/patches-3.18/516-board_96348A-122.patch b/target/linux/brcm63xx/patches-3.18/516-board_96348A-122.patch new file mode 100644 index 0000000000..3352d5e508 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/516-board_96348A-122.patch @@ -0,0 +1,95 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -583,6 +583,76 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_96348A_122 = { ++ .name = "96348A-122", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ ++ .leds = { ++ { ++ .name = "96348A-122:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "96348A-122:red:alarm", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "96348A-122:green:wps", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 35, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++}; ++ + static struct board_info __initdata board_96348gw = { + .name = "96348GW", + .expected_cpu_id = 0x6348, +@@ -1850,6 +1920,7 @@ static const struct board_info __initcon + &board_V2500V_BB, + &board_V2110, + &board_ct536_ct5621, ++ &board_96348A_122, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 +@@ -1887,6 +1958,7 @@ static struct of_device_id const bcm963x + { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, }, + { .compatible = "brcm,bcm96348gw-a", .data = &board_96348gw_a, }, + { .compatible = "comtrend,ct-536+", .data = &board_ct536_ct5621, }, ++ { .compatible = "comtrend,ct-5365", .data = &board_96348A_122, }, + { .compatible = "comtrend,ct-5621", .data = &board_ct536_ct5621, }, + { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, diff --git a/target/linux/brcm63xx/patches-3.18/517-RTA1205W_16_uart_fixes.patch b/target/linux/brcm63xx/patches-3.18/517-RTA1205W_16_uart_fixes.patch new file mode 100644 index 0000000000..10d2508e19 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/517-RTA1205W_16_uart_fixes.patch @@ -0,0 +1,10 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -857,6 +857,7 @@ static struct board_info __initdata boar + .name = "RTA1025W_16", + .expected_cpu_id = 0x6348, + ++ .has_uart0 = 1, + .has_enet0 = 1, + .has_enet1 = 1, + .has_pci = 1, diff --git a/target/linux/brcm63xx/patches-3.18/519_board_CPVA502plus.patch b/target/linux/brcm63xx/patches-3.18/519_board_CPVA502plus.patch new file mode 100644 index 0000000000..d7a808763c --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/519_board_CPVA502plus.patch @@ -0,0 +1,51 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -530,6 +530,40 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_CPVA502plus = { ++ .name = "CPVA502+", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ }, ++ ++ .leds = { ++ { ++ .name = "CPVA502+:green:phone", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "CPVA502+:amber:link", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ }, ++ ++ .ephy_reset_gpio = 4, ++ .ephy_reset_gpio_flags = GPIOF_INIT_HIGH, ++}; + + static struct board_info __initdata board_ct536_ct5621 = { + .name = "CT536_CT5621", +@@ -1922,6 +1956,7 @@ static const struct board_info __initcon + &board_V2110, + &board_ct536_ct5621, + &board_96348A_122, ++ &board_CPVA502plus, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.18/520-bcm63xx-add-support-for-96368MVWG-board.patch b/target/linux/brcm63xx/patches-3.18/520-bcm63xx-add-support-for-96368MVWG-board.patch new file mode 100644 index 0000000000..9da54bba91 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/520-bcm63xx-add-support-for-96368MVWG-board.patch @@ -0,0 +1,145 @@ +From eeacc2529942051504bc957726aa178671344421 Mon Sep 17 00:00:00 2001 +From: Maxime Bizon <mbizon@freebox.fr> +Date: Wed, 20 Jan 2010 16:21:30 +0100 +Subject: [PATCH 32/63] bcm63xx: add support for 96368MVWG board. + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 95 ++++++++++++++++++++ + .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 + + 2 files changed, 97 insertions(+), 0 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1920,6 +1920,85 @@ static struct board_info __initdata boar + #endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* ++ * known 6368 boards ++ */ ++#ifdef CONFIG_BCM63XX_CPU_6368 ++static struct board_info __initdata board_96368mvwg = { ++ .name = "96368MVWG", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ ++ .has_usbd = 1, ++ ++ .usbd = { ++ .use_fullspeed = 0, ++ .port_no = 0, ++ }, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port1", ++ }, ++ ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port2", ++ }, ++ ++ [4] = { ++ .used = 1, ++ .phy_id = 0x12, ++ .name = "port0", ++ }, ++ ++ [5] = { ++ .used = 1, ++ .phy_id = 0x11, ++ .name = "port3", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "96368MVWG:green:adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "96368MVWG:green:ppp", ++ .gpio = 5, ++ }, ++ { ++ .name = "96368MVWG:green:power", ++ .gpio = 22, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "96368MVWG:green:wps", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "96368MVWG:red:ppp-fail", ++ .gpio = 31, ++ }, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++}; ++#endif /* CONFIG_BCM63XX_CPU_6368 */ ++ ++/* + * all boards + */ + static const struct board_info __initconst *bcm963xx_boards[] = { +@@ -1971,6 +2050,10 @@ static const struct board_info __initcon + &board_HW553, + &board_spw303v, + #endif ++ ++#ifdef CONFIG_BCM63XX_CPU_6368 ++ &board_96368mvwg, ++#endif + }; + + static struct of_device_id const bcm963xx_boards_dt[] = { +@@ -2019,6 +2102,7 @@ static struct of_device_id const bcm963x + { .compatible = "t-com,spw303v", .data = &board_spw303v, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6368 ++ { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 + { .compatible = "brcm,bcm963268bu_p300", .data = &board_963268bu_p300, }, +--- a/arch/mips/bcm63xx/boards/board_common.c ++++ b/arch/mips/bcm63xx/boards/board_common.c +@@ -88,12 +88,25 @@ void __init board_early_setup(const stru + bcm63xx_pci_enabled = 1; + if (BCMCPU_IS_6348()) + val |= GPIO_MODE_6348_G2_PCI; ++ ++ if (BCMCPU_IS_6368()) ++ val |= GPIO_MODE_6368_PCI_REQ1 | ++ GPIO_MODE_6368_PCI_GNT1 | ++ GPIO_MODE_6368_PCI_INTB | ++ GPIO_MODE_6368_PCI_REQ0 | ++ GPIO_MODE_6368_PCI_GNT0; + } + #endif + + if (board.has_pccard) { + if (BCMCPU_IS_6348()) + val |= GPIO_MODE_6348_G1_MII_PCCARD; ++ ++ if (BCMCPU_IS_6368()) ++ val |= GPIO_MODE_6368_PCMCIA_CD1 | ++ GPIO_MODE_6368_PCMCIA_CD2 | ++ GPIO_MODE_6368_PCMCIA_VS1 | ++ GPIO_MODE_6368_PCMCIA_VS2; + } + + if (board.has_enet0 && !board.enet0.use_internal_phy) { diff --git a/target/linux/brcm63xx/patches-3.18/521-bcm63xx-add-support-for-96368MVNgr-board.patch b/target/linux/brcm63xx/patches-3.18/521-bcm63xx-add-support-for-96368MVNgr-board.patch new file mode 100644 index 0000000000..8975c9d642 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/521-bcm63xx-add-support-for-96368MVNgr-board.patch @@ -0,0 +1,100 @@ +From f457fc2eb9bb915b5a4d251c7c68d4694cf07b01 Mon Sep 17 00:00:00 2001 +From: Maxime Bizon <mbizon@freebox.fr> +Date: Fri, 4 Nov 2011 12:33:48 +0100 +Subject: [PATCH 33/63] bcm63xx: add support for 96368MVNgr board. + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 67 +++++++++++++++++++++++++++++ + 1 files changed, 67 insertions(+), 0 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1996,6 +1996,72 @@ static struct board_info __initdata boar + .has_ohci0 = 1, + .has_ehci0 = 1, + }; ++ ++static struct board_info __initdata board_96368mvngr = { ++ .name = "96368MVNgr", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "96368MVNgr:green:adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "96368MVNgr:green:inet", ++ .gpio = 5, ++ }, ++ { ++ .name = "96368MVNgr:green:power", ++ .gpio = 22, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "96368MVNgr:green:wps", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "96368MVNgr:green:inet-fail", ++ .gpio = 3, ++ }, ++ }, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++}; + #endif /* CONFIG_BCM63XX_CPU_6368 */ + + /* +@@ -2053,6 +2119,7 @@ static const struct board_info __initcon + + #ifdef CONFIG_BCM63XX_CPU_6368 + &board_96368mvwg, ++ &board_96368mvngr, + #endif + }; + +@@ -2102,6 +2169,7 @@ static struct of_device_id const bcm963x + { .compatible = "t-com,spw303v", .data = &board_spw303v, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6368 ++ { .compatible = "brcm,bcm96368mvngr", .data = &board_96368mvngr, }, + { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 diff --git a/target/linux/brcm63xx/patches-3.18/522-MIPS-BCM63XX-add-96328avng-reference-board.patch b/target/linux/brcm63xx/patches-3.18/522-MIPS-BCM63XX-add-96328avng-reference-board.patch new file mode 100644 index 0000000000..680a230bae --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/522-MIPS-BCM63XX-add-96328avng-reference-board.patch @@ -0,0 +1,67 @@ +From c93c2bbf0cc96da5a47d77f01daf6c983cfe4216 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Tue, 29 May 2012 10:52:25 +0200 +Subject: [PATCH] MIPS: BCM63XX: add 96328avng reference board + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 77 +++++++++++++++++++++++++++++ + 1 files changed, 77 insertions(+), 0 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -93,13 +93,45 @@ static struct board_info __initdata boar + .port_no = 0, + }, + ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ + .leds = { + { +- .name = "96328avng::ppp-fail", ++ .name = "96328avng::internet-fail", + .gpio = 2, + .active_low = 1, + }, + { ++ .name = "96328avng::dsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { + .name = "96328avng::power", + .gpio = 4, + .active_low = 1, +@@ -116,7 +148,7 @@ static struct board_info __initdata boar + .active_low = 1, + }, + { +- .name = "96328avng::ppp", ++ .name = "96328avng::internet", + .gpio = 11, + .active_low = 1, + }, diff --git a/target/linux/brcm63xx/patches-3.18/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch b/target/linux/brcm63xx/patches-3.18/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch new file mode 100644 index 0000000000..8fef7d547b --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/523-MIPS-BCM63XX-add-963281TAN-reference-board.patch @@ -0,0 +1,104 @@ +From f0649f7b7c672cf452a1796a1422bf615e1973f8 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Tue, 29 May 2012 11:01:12 +0200 +Subject: [PATCH] MIPS: BCM63XX: add 963281TAN reference board + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 71 +++++++++++++++++++++++++++++ + 1 files changed, 71 insertions(+), 0 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -154,6 +154,76 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_963281TAN = { ++ .name = "963281TAN", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "963281TAN::internet", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "963281TAN::power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "963281TAN::internet-fail", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "963281TAN::power-fail", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "963281TAN::wps", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "963281TAN::dsl", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6328 */ + + /* +@@ -2105,6 +2175,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, ++ &board_963281TAN, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + &board_96338gw, +@@ -2161,6 +2232,7 @@ static struct of_device_id const bcm963x + { .compatible = "netgear,cvg834g", .data = &board_cvg834g, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 ++ { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 diff --git a/target/linux/brcm63xx/patches-3.18/524-board_dsl_274xb_rev_f.patch b/target/linux/brcm63xx/patches-3.18/524-board_dsl_274xb_rev_f.patch new file mode 100644 index 0000000000..d8b8cc4500 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/524-board_dsl_274xb_rev_f.patch @@ -0,0 +1,140 @@ +From 66808f706b3dcd83a9f5157997ff478a880a2906 Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jonas.gorski@gmail.com> +Date: Mon, 30 Apr 2012 09:10:51 +0200 +Subject: [PATCH 70/79] MIPS: BCM63XX: Add board definition for D-Link + DSL-274xB rev F1 + +--- + arch/mips/bcm63xx/boards/board_bcm963xx.c | 104 +++++++++++++++++++++++++++++ + 1 files changed, 104 insertions(+), 0 deletions(-) + +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -224,6 +224,111 @@ static struct board_info __initdata boar + + }, + }; ++ ++static struct board_info __initdata board_dsl_274xb_f1 = { ++ .name = "AW4339U", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ ++ .has_caldata = 1, ++ .caldata = { ++ { ++ .vendor = PCI_VENDOR_ID_ATHEROS, ++ .caldata_offset = 0x7d1000, ++ .slot = 0, ++ .led_pin = -1, ++ }, ++ }, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 4", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 3", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 2", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 1", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "dsl-274xb:red:internet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:green:dsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "dsl-274xb:red:power", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:blue:wps", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-274xb:green:internet", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "wifi", ++ .gpio = 10, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = BTN_0, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 24, ++ .active_low = 1, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6328 */ + + /* +@@ -2176,6 +2281,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, + &board_963281TAN, ++ &board_dsl_274xb_f1, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + &board_96338gw, +@@ -2234,6 +2340,7 @@ static struct of_device_id const bcm963x + #ifdef CONFIG_BCM63XX_CPU_6328 + { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, ++ { .compatible = "d-link,dsl-274xb-f", .data = &board_dsl_274xb_f1, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + { .compatible = "brcm,bcm96338gw", .data = &board_96338gw, }, diff --git a/target/linux/brcm63xx/patches-3.18/525-board_96348w3.patch b/target/linux/brcm63xx/patches-3.18/525-board_96348w3.patch new file mode 100644 index 0000000000..0dd54daad7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/525-board_96348w3.patch @@ -0,0 +1,70 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1158,6 +1158,59 @@ static struct board_info __initdata boar + .has_ohci0 = 1, + }; + ++/* NetGear DG834G v4 */ ++static struct board_info __initdata board_96348W3 = { ++ .name = "96348W3", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .has_ohci0 = 1, ++ ++ .leds = { ++ { ++ .name = "96348W3:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "96348W3:red:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "96348W3::adsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "96348W3::internet", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 6, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + static struct board_info __initdata board_96348_D4PW = { + .name = "D-4P-W", + .expected_cpu_id = 0x6348, +@@ -2311,6 +2364,7 @@ static const struct board_info __initcon + &board_ct536_ct5621, + &board_96348A_122, + &board_CPVA502plus, ++ &board_96348W3, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 diff --git a/target/linux/brcm63xx/patches-3.18/526-board_CT6373-1.patch b/target/linux/brcm63xx/patches-3.18/526-board_CT6373-1.patch new file mode 100644 index 0000000000..5c823fea00 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/526-board_CT6373-1.patch @@ -0,0 +1,156 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -43,6 +43,12 @@ + #define NB4_SPI_GPIO_CLK 6 + #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) + ++#define CT6373_PID_OFFSET 0xff80 ++#define CT6373_74X164_GPIO_BASE 64 ++#define CT6373_SPI_GPIO_MOSI 7 ++#define CT6373_SPI_GPIO_CLK 6 ++#define CT6373_74HC64_GPIO(X) (CT6373_74X164_GPIO_BASE + (X)) ++ + /* + * known 3368 boards + */ +@@ -2035,6 +2041,124 @@ static struct board_info __initdata boar + .num_spis = ARRAY_SIZE(nb4_spi_devices), + }; + ++ ++struct spi_gpio_platform_data ct6373_spi_gpio_data = { ++ .sck = CT6373_SPI_GPIO_CLK, ++ .mosi = CT6373_SPI_GPIO_MOSI, ++ .miso = SPI_GPIO_NO_MISO, ++ .num_chipselect = 1, ++}; ++ ++static struct platform_device ct6373_spi_gpio = { ++ .name = "spi_gpio", ++ .id = 1, ++ .dev = { ++ .platform_data = &ct6373_spi_gpio_data, ++ }, ++}; ++ ++static struct platform_device * __initdata ct6373_devices[] = { ++ &ct6373_spi_gpio, ++}; ++ ++#if 0 /* FIXME: 3.14 dropped non-DT support */ ++const struct gen_74x164_chip_platform_data ct6373_74x164_platform_data = { ++ .base = CT6373_74X164_GPIO_BASE ++}; ++#endif ++ ++static struct spi_board_info ct6373_spi_devices[] = { ++#if 0 /* FIXME: 3.14 dropped non-DT support */ ++ { ++ .modalias = "74x164", ++ .max_speed_hz = 781000, ++ .bus_num = 1, ++ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT, ++ .mode = SPI_MODE_0, ++ .platform_data = &ct6373_74x164_platform_data ++ } ++#endif ++}; ++ ++static struct board_info __initdata board_ct6373_1 = { ++ .name = "CT6373-1", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "CT6373-1:green:power", ++ .gpio = 0, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "CT6373-1:green:usb", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "CT6373-1:green:wlan", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "CT6373-1:green:adsl", ++ .gpio = CT6373_74HC64_GPIO(0), ++ .active_low = 1, ++ }, ++ { ++ .name = "CT6373-1:green:line", ++ .gpio = CT6373_74HC64_GPIO(1), ++ .active_low = 1, ++ }, ++ { ++ .name = "CT6373-1:green:fxs1", ++ .gpio = CT6373_74HC64_GPIO(2), ++ .active_low = 1, ++ }, ++ { ++ .name = "CT6373-1:green:fxs2", ++ .gpio = CT6373_74HC64_GPIO(3), ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 35, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++ ++ .devs = ct6373_devices, ++ .num_devs = ARRAY_SIZE(ct6373_devices), ++ .spis = ct6373_spi_devices, ++ .num_spis = ARRAY_SIZE(ct6373_spi_devices), ++}; ++ + static struct board_info __initdata board_HW553 = { + .name = "HW553", + .expected_cpu_id = 0x6358, +@@ -2376,6 +2500,7 @@ static const struct board_info __initcon + &board_dsl_274xb_rev_c, + &board_nb4_ser_r0, + &board_nb4_fxc_r1, ++ &board_ct6373_1, + &board_HW553, + &board_spw303v, + #endif +@@ -2422,6 +2547,7 @@ static struct of_device_id const bcm963x + { .compatible = "alcatel,rg100a", .data = &board_96358vw2, }, + { .compatible = "brcm,bcm96358vw", .data = &board_96358vw, }, + { .compatible = "brcm,bcm96358vw2", .data = &board_96358vw2, }, ++ { .compatible = "comtrend,ct-6373", .data = &board_ct6373_1, }, + { .compatible = "d-link,dsl-274xb-c2", .data = &board_dsl_274xb_rev_c, }, + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, + { .compatible = "huawei,hg553", .data = &board_HW553, }, diff --git a/target/linux/brcm63xx/patches-3.18/527-board_dva-g3810bn-tl-1.patch b/target/linux/brcm63xx/patches-3.18/527-board_dva-g3810bn-tl-1.patch new file mode 100644 index 0000000000..df5f0fcb88 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/527-board_dva-g3810bn-tl-1.patch @@ -0,0 +1,92 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -2301,6 +2301,73 @@ static struct board_info __initdata boar + }, + } + }; ++ ++/* D-Link DVA-G3810BN/TL */ ++static struct board_info __initdata board_DVAG3810BN = { ++ .name = "DVAG3810BN", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_enet0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet0 = { ++ .has_phy = 0, ++ .use_internal_phy = 1, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ ++ .has_ohci0 = 1, ++ .has_pccard = 1, ++ .has_ehci0 = 1, ++ ++ .leds = { ++ { ++ .name = "DVAG3810BN::voip", ++ .gpio = 1, ++ }, ++ { ++ .name = "DVAG3810BN::dsl", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "DVAG3810BN::internet", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "DVAG3810BN::power", ++ .gpio = 4, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "DVAG3810BN::stop", ++ .gpio = 5, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6358 */ + + /* +@@ -2503,6 +2570,7 @@ static const struct board_info __initcon + &board_ct6373_1, + &board_HW553, + &board_spw303v, ++ &board_DVAG3810BN, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6368 +@@ -2550,6 +2618,7 @@ static struct of_device_id const bcm963x + { .compatible = "comtrend,ct-6373", .data = &board_ct6373_1, }, + { .compatible = "d-link,dsl-274xb-c2", .data = &board_dsl_274xb_rev_c, }, + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, ++ { .compatible = "d-link,dva-g3810bn/tl", .data = &board_DVAG3810BN, }, + { .compatible = "huawei,hg553", .data = &board_HW553, }, + { .compatible = "pirelli,a226g", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, diff --git a/target/linux/brcm63xx/patches-3.18/528-board_nb6.patch b/target/linux/brcm63xx/patches-3.18/528-board_nb6.patch new file mode 100644 index 0000000000..bdb77c40f4 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/528-board_nb6.patch @@ -0,0 +1,145 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -18,6 +18,7 @@ + #if 0 /* FIXME: 3.14 removed non-DT support */ + #include <linux/spi/74x164.h> + #endif ++#include <linux/rtl8367.h> + #include <asm/addrspace.h> + #include <bcm63xx_board.h> + #include <bcm63xx_cpu.h> +@@ -42,6 +43,8 @@ + #define NB4_SPI_GPIO_MOSI 7 + #define NB4_SPI_GPIO_CLK 6 + #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X)) ++#define NB6_GPIO_RTL8367_SDA 18 ++#define NB6_GPIO_RTL8367_SCK 20 + + #define CT6373_PID_OFFSET 0xff80 + #define CT6373_74X164_GPIO_BASE 64 +@@ -2370,6 +2373,104 @@ static struct board_info __initdata boar + }; + #endif /* CONFIG_BCM63XX_CPU_6358 */ + ++#ifdef CONFIG_BCM63XX_CPU_6362 ++static struct rtl8367_extif_config nb6_rtl8367_extif0_cfg = { ++ .mode = RTL8367_EXTIF_MODE_RGMII, ++ .txdelay = 1, ++ .rxdelay = 5, ++ .ability = { ++ .force_mode = 1, ++ .txpause = 1, ++ .rxpause = 1, ++ .link = 1, ++ .duplex = 1, ++ .speed = RTL8367_PORT_SPEED_1000, ++ }, ++}; ++ ++static struct rtl8367_platform_data nb6_rtl8367_data = { ++ .gpio_sda = NB6_GPIO_RTL8367_SDA, ++ .gpio_sck = NB6_GPIO_RTL8367_SCK, ++ .extif0_cfg = &nb6_rtl8367_extif0_cfg, ++}; ++ ++static struct platform_device nb6_rtl8367_device = { ++ .name = RTL8367_DRIVER_NAME, ++ .id = -1, ++ .dev = { ++ .platform_data = &nb6_rtl8367_data, ++ } ++}; ++ ++static struct platform_device * __initdata nb6_devices[] = { ++ &nb6_rtl8367_device, ++}; ++ ++static struct board_info __initdata board_nb6 = { ++ .name = "NB6", ++ .expected_cpu_id = 0x6362, ++ ++ .has_uart0 = 1, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [4] = { ++ .used = 1, ++ .phy_id = 0xff, ++ .bypass_link = 1, ++ .force_speed = 1000, ++ .force_duplex_full = 1, ++ .name = "RGMII", ++ }, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 24, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 25, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 12, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ { ++ .desc = "service", ++ .gpio = 10, ++ .type = EV_KEY, ++ .code = BTN_0, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ }, ++ ++ .devs = nb6_devices, ++ .num_devs = ARRAY_SIZE(nb6_devices), ++}; ++#endif /* CONFIG_BCM63XX_CPU_6362 */ ++ + /* + * known 6368 boards + */ +@@ -2573,6 +2674,10 @@ static const struct board_info __initcon + &board_DVAG3810BN, + #endif + ++#ifdef CONFIG_BCM63XX_CPU_6362 ++ &board_nb6, ++#endif ++ + #ifdef CONFIG_BCM63XX_CPU_6368 + &board_96368mvwg, + &board_96368mvngr, +@@ -2628,6 +2733,9 @@ static struct of_device_id const bcm963x + { .compatible = "sfr,nb4-fxc-r1", .data = &board_nb4_fxc_r1, }, + { .compatible = "t-com,spw303v", .data = &board_spw303v, }, + #endif ++#ifdef CONFIG_BCM63XX_CPU_6362 ++ { .compatible = "sfr,nb6-ser-r0", .data = &board_nb6, }, ++#endif + #ifdef CONFIG_BCM63XX_CPU_6368 + { .compatible = "brcm,bcm96368mvngr", .data = &board_96368mvngr, }, + { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, diff --git a/target/linux/brcm63xx/patches-3.18/529-board_fast2604.patch b/target/linux/brcm63xx/patches-3.18/529-board_fast2604.patch new file mode 100644 index 0000000000..9f74abf808 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/529-board_fast2604.patch @@ -0,0 +1,76 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1103,6 +1103,57 @@ static struct board_info __initdata boar + .has_ehci0 = 1, + }; + ++static struct board_info __initdata board_FAST2604 = { ++ .name = "F@ST2604", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "F@ST2604:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "F@ST2604:red:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2604:red:inet", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2604:green:wps", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + static struct board_info __initdata board_rta1025w_16 = { + .name = "RTA1025W_16", + .expected_cpu_id = 0x6348, +@@ -2645,6 +2696,7 @@ static const struct board_info __initcon + &board_96348gw_10, + &board_96348gw_11, + &board_FAST2404, ++ &board_FAST2604, + &board_DV201AMR, + &board_96348gw_a, + &board_rta1025w_16, +@@ -2712,6 +2764,7 @@ static struct of_device_id const bcm963x + { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, }, + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, }, + { .compatible = "sagem,f@st2404", .data = &board_FAST2404, }, ++ { .compatible = "sagem,f@st2604", .data = &board_FAST2604, }, + { .compatible = "t-com,spw500v", .data = &board_spw500v, }, + { .compatible = "tecom,gw6000", .data = &board_gw6000, }, + { .compatible = "tecom,gw6200", .data = &board_gw6200, }, diff --git a/target/linux/brcm63xx/patches-3.18/530-board_A4001N1.patch b/target/linux/brcm63xx/patches-3.18/530-board_A4001N1.patch new file mode 100644 index 0000000000..9a05d98548 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/530-board_A4001N1.patch @@ -0,0 +1,152 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -234,6 +234,133 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_A4001N1 = { ++ .name = "963281T_TEF", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "A4001N1:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "A4001N1:red:power", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:green:inet", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:red:inet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:green:ppp", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:red:ppp", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:green:3g", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:red:3g", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:green:wlan", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:red:wlan", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:green:eth", ++ .gpio = 31, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N1:red:eth", ++ .gpio = 20, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 24, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43225, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ }, ++}; ++ + static struct board_info __initdata board_dsl_274xb_f1 = { + .name = "AW4339U", + .expected_cpu_id = 0x6328, +@@ -2677,6 +2804,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, + &board_963281TAN, ++ &board_A4001N1, + &board_dsl_274xb_f1, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 +@@ -2742,6 +2870,7 @@ static struct of_device_id const bcm963x + { .compatible = "netgear,cvg834g", .data = &board_cvg834g, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 ++ { .compatible = "adb,a4001n1", .data = &board_A4001N1, }, + { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, + { .compatible = "d-link,dsl-274xb-f", .data = &board_dsl_274xb_f1, }, diff --git a/target/linux/brcm63xx/patches-3.18/531-board_AR-5387un.patch b/target/linux/brcm63xx/patches-3.18/531-board_AR-5387un.patch new file mode 100644 index 0000000000..82d6c807a5 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/531-board_AR-5387un.patch @@ -0,0 +1,134 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -164,6 +164,115 @@ static struct board_info __initdata boar + }, + }; + ++static struct sprom_fixup __initdata ar5387un_fixups[] = { ++ { .offset = 2, .value = 0x05bb }, ++ { .offset = 65, .value = 0x1204 }, ++ { .offset = 78, .value = 0x0303 }, ++ { .offset = 79, .value = 0x0202 }, ++ { .offset = 80, .value = 0xff02 }, ++ { .offset = 87, .value = 0x0315 }, ++ { .offset = 88, .value = 0x0315 }, ++ { .offset = 96, .value = 0x2048 }, ++ { .offset = 97, .value = 0xff11 }, ++ { .offset = 98, .value = 0x1567 }, ++ { .offset = 99, .value = 0xfb24 }, ++ { .offset = 100, .value = 0x3e3c }, ++ { .offset = 101, .value = 0x4038 }, ++ { .offset = 102, .value = 0xfe7f }, ++ { .offset = 103, .value = 0x1279 }, ++ { .offset = 112, .value = 0x2048 }, ++ { .offset = 113, .value = 0xff03 }, ++ { .offset = 114, .value = 0x154c }, ++ { .offset = 115, .value = 0xfb27 }, ++ { .offset = 116, .value = 0x3e3c }, ++ { .offset = 117, .value = 0x4038 }, ++ { .offset = 118, .value = 0xfe87 }, ++ { .offset = 119, .value = 0x1233 }, ++ { .offset = 203, .value = 0x2226 }, ++}; ++ ++static struct board_info __initdata board_AR5387un = { ++ .name = "96328A-1441N1", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "AR-5387un:green:power", ++ .gpio = 8, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "AR-5387un:red:power", ++ .gpio = 4, ++ }, ++ { ++ .name = "AR-5387un:green:inet", ++ .gpio = 7, ++ }, ++ { ++ .name = "AR-5387un:red:inet", ++ .gpio = 1, ++ }, ++ { ++ .name = "AR-5387un:green:dsl", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43225, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ .board_fixups = ar5387un_fixups, ++ .num_board_fixups = ARRAY_SIZE(ar5387un_fixups), ++ }, ++}; ++ + static struct board_info __initdata board_963281TAN = { + .name = "963281TAN", + .expected_cpu_id = 0x6328, +@@ -2803,6 +2912,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, ++ &board_AR5387un, + &board_963281TAN, + &board_A4001N1, + &board_dsl_274xb_f1, +@@ -2873,6 +2983,7 @@ static struct of_device_id const bcm963x + { .compatible = "adb,a4001n1", .data = &board_A4001N1, }, + { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, ++ { .compatible = "comtrend,ar-5387un", .data = &board_AR5387un, }, + { .compatible = "d-link,dsl-274xb-f", .data = &board_dsl_274xb_f1, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 diff --git a/target/linux/brcm63xx/patches-3.18/532-board_AR-5381u.patch b/target/linux/brcm63xx/patches-3.18/532-board_AR-5381u.patch new file mode 100644 index 0000000000..941bf8fdfa --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/532-board_AR-5381u.patch @@ -0,0 +1,110 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -164,6 +164,91 @@ static struct board_info __initdata boar + }, + }; + ++static struct sprom_fixup __initdata ar5381u_fixups[] = { ++ { .offset = 97, .value = 0xfee5 }, ++ { .offset = 98, .value = 0x157c }, ++ { .offset = 99, .value = 0xfae7 }, ++ { .offset = 113, .value = 0xfefa }, ++ { .offset = 114, .value = 0x15d6 }, ++ { .offset = 115, .value = 0xfaf8 }, ++}; ++ ++static struct board_info __initdata board_AR5381u = { ++ .name = "96328A-1241N", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "AR-5381u:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "AR-5381u:red:alarm", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "AR-5381u:green:inet", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43225, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ .board_fixups = ar5381u_fixups, ++ .num_board_fixups = ARRAY_SIZE(ar5381u_fixups), ++ }, ++}; ++ + static struct sprom_fixup __initdata ar5387un_fixups[] = { + { .offset = 2, .value = 0x05bb }, + { .offset = 65, .value = 0x1204 }, +@@ -2912,6 +2997,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, ++ &board_AR5381u, + &board_AR5387un, + &board_963281TAN, + &board_A4001N1, +@@ -2983,6 +3069,7 @@ static struct of_device_id const bcm963x + { .compatible = "adb,a4001n1", .data = &board_A4001N1, }, + { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, ++ { .compatible = "comtrend,ar-5381u", .data = &board_AR5381u, }, + { .compatible = "comtrend,ar-5387un", .data = &board_AR5387un, }, + { .compatible = "d-link,dsl-274xb-f", .data = &board_dsl_274xb_f1, }, + #endif diff --git a/target/linux/brcm63xx/patches-3.18/533-board_rta770bw.patch b/target/linux/brcm63xx/patches-3.18/533-board_rta770bw.patch new file mode 100644 index 0000000000..059823ea06 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/533-board_rta770bw.patch @@ -0,0 +1,66 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -833,6 +833,55 @@ static struct board_info __initdata boar + + .has_uart0 = 1, + }; ++ ++static struct board_info __initdata board_rta770bw = { ++ .name = "RTA770BW", ++ .expected_cpu_id = 0x6345, ++ ++ .has_uart0 = 1, ++ ++ .has_enet0 = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "RTA770BW:green:usb", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA770BW:green:adsl", ++ .gpio = 8, ++ }, ++ { ++ .name = "RTA770BW:green:diag", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA770BW:green:wlan", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 13, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6345 */ + + /* +@@ -3011,6 +3060,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_6345 + &board_96345gw2, ++ &board_rta770bw, + #endif + #ifdef CONFIG_BCM63XX_CPU_6348 + &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.18/534-board_hw556.patch b/target/linux/brcm63xx/patches-3.18/534-board_hw556.patch new file mode 100644 index 0000000000..06ad96a96d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/534-board_hw556.patch @@ -0,0 +1,433 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -12,6 +12,7 @@ + #include <linux/string.h> + #include <linux/gpio_keys.h> + #include <linux/input.h> ++#include <linux/pci_ids.h> + #include <linux/platform_device.h> + #include <linux/spi/spi.h> + #include <linux/spi/spi_gpio.h> +@@ -2660,6 +2661,402 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_HW556_C = { ++ .name = "HW556_C", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .has_caldata = 1, ++ .caldata = { ++ { ++ .vendor = PCI_VENDOR_ID_RALINK, ++ .caldata_offset = 0xeffe00, ++ .slot = 1, ++ .eeprom = "rt2x00.eeprom", ++ }, ++ }, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "HW556:green:lan1", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan2", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:power", ++ .gpio = 3, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW556:red:message", ++ .gpio = 12, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan1", ++ .gpio = 13, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:hspa", ++ .gpio = 15, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan2", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan3", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan3", ++ .gpio = 26, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan4", ++ .gpio = 27, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan4", ++ .gpio = 28, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "help", ++ .gpio = 8, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_HELP, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 9, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "restart", ++ .gpio = 10, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 11, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_CONFIG, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++static struct board_info __initdata board_HW556_A = { ++ .name = "HW556_A", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .has_caldata = 1, ++ .caldata = { ++ { ++ .vendor = PCI_VENDOR_ID_ATHEROS, ++ .caldata_offset = 0xf7e000, ++ .slot = 1, ++ .endian_check = 1, ++ .led_pin = 2, ++ }, ++ }, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "HW556:red:message", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:hspa", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:power", ++ .gpio = 3, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW556:red:all", ++ .gpio = 6, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW556:green:lan1", ++ .gpio = 12, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan1", ++ .gpio = 13, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan2", ++ .gpio = 15, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan2", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan3", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan3", ++ .gpio = 26, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan4", ++ .gpio = 27, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan4", ++ .gpio = 28, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "help", ++ .gpio = 8, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_HELP, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 9, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "restart", ++ .gpio = 10, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 11, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_CONFIG, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++static struct board_info __initdata board_HW556_B = { ++ .name = "HW556_B", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 2, ++ ++ .has_caldata = 1, ++ .caldata = { ++ { ++ .vendor = PCI_VENDOR_ID_ATHEROS, ++ .caldata_offset = 0xefe000, ++ .slot = 1, ++ .endian_check = 1, ++ .led_pin = 2, ++ }, ++ }, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "HW556:red:message", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:hspa", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:power", ++ .gpio = 3, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW556:red:all", ++ .gpio = 6, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "HW556:green:lan1", ++ .gpio = 12, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan1", ++ .gpio = 13, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan2", ++ .gpio = 15, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan2", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan3", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan3", ++ .gpio = 26, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:green:lan4", ++ .gpio = 27, ++ .active_low = 1, ++ }, ++ { ++ .name = "HW556:red:lan4", ++ .gpio = 28, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "help", ++ .gpio = 8, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_HELP, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wlan", ++ .gpio = 9, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "restart", ++ .gpio = 10, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 11, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_CONFIG, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + /* T-Home Speedport W 303V Typ B */ + static struct board_info __initdata board_spw303v = { + .name = "96358-502V", +@@ -3096,6 +3493,9 @@ static const struct board_info __initcon + &board_nb4_fxc_r1, + &board_ct6373_1, + &board_HW553, ++ &board_HW556_A, ++ &board_HW556_B, ++ &board_HW556_C, + &board_spw303v, + &board_DVAG3810BN, + #endif +@@ -3155,6 +3555,9 @@ static struct of_device_id const bcm963x + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, + { .compatible = "d-link,dva-g3810bn/tl", .data = &board_DVAG3810BN, }, + { .compatible = "huawei,hg553", .data = &board_HW553, }, ++ { .compatible = "huawei,hg556a-a", .data = &board_HW556_A, }, ++ { .compatible = "huawei,hg556a-b", .data = &board_HW556_B, }, ++ { .compatible = "huawei,hg556a-c", .data = &board_HW556_C, }, + { .compatible = "pirelli,a226g", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m", .data = &board_DWVS0, }, + { .compatible = "pirelli,a226m-fwb", .data = &board_DWVS0, }, diff --git a/target/linux/brcm63xx/patches-3.18/535-board_rta770w.patch b/target/linux/brcm63xx/patches-3.18/535-board_rta770w.patch new file mode 100644 index 0000000000..0d55786467 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/535-board_rta770w.patch @@ -0,0 +1,71 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -883,6 +883,60 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++// Actually this board is the very same as the rta770bw, ++// where the additional 'b' within the name just ++// just indicates 'Annex B'. The ADSL Modem itself is able ++// to handle both Annex A as well as Annex B - ++// the loaded firmware makes the only difference ++static struct board_info __initdata board_rta770w = { ++ .name = "RTA770W", ++ .expected_cpu_id = 0x6345, ++ ++ .has_uart0 = 1, ++ ++ .has_enet0 = 1, ++ ++ .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "RTA770W:green:usb", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA770W:green:adsl", ++ .gpio = 8, ++ }, ++ { ++ .name = "RTA770W:green:diag", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "RTA770W:green:wlan", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 13, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .active_low = 1, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6345 */ + + /* +@@ -3458,6 +3512,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6345 + &board_96345gw2, + &board_rta770bw, ++ &board_rta770w, + #endif + #ifdef CONFIG_BCM63XX_CPU_6348 + &board_96348r, diff --git a/target/linux/brcm63xx/patches-3.18/536-board_fast2704.patch b/target/linux/brcm63xx/patches-3.18/536-board_fast2704.patch new file mode 100644 index 0000000000..95388a29fe --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/536-board_fast2704.patch @@ -0,0 +1,153 @@ +From: Marcin Jurkowski <marcin1j@gmail.com> +Date: Thu, 31 Oct 2013 22:33:10 +0000 +Subject: [PATCH] bcm63xx: Add kernel support for Sagemcom F@ST2704V2 ADSL + router + +This adds kernel support support for Sagemcom F@st 2704 wireless ADSL +router. +It's a BCM6328-based 802.11n wireless router with USB port and ADSL2+ +modem equipped with 64 MiB RAM and 8 MiB flash. + +Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com> +--- +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -660,6 +660,122 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_FAST2704V2 = { ++ .name = "F@ST2704V2", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .has_usbd = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ /* front LEDs */ ++ { ++ .name = "F@ST2704V2:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "F@ST2704V2:red:power", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:red:inet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:dsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:inet", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "F@ST2704V2:green:usb", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ ++ /* side button LEDs */ ++ { ++ .name = "F@ST2704V2:green:wps", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ ++ /* FIXME: can't control gpio0 line in "out" state, needs further investigation */ ++ /* ++ { ++ .name = "F@ST2704V2:green:rfkill", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ */ ++ ++ }, ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 24, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "rfkill", ++ .gpio = 15, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6328 */ + + /* +@@ -3502,6 +3618,7 @@ static const struct board_info __initcon + &board_963281TAN, + &board_A4001N1, + &board_dsl_274xb_f1, ++ &board_FAST2704V2, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + &board_96338gw, +@@ -3577,6 +3694,7 @@ static struct of_device_id const bcm963x + { .compatible = "comtrend,ar-5381u", .data = &board_AR5381u, }, + { .compatible = "comtrend,ar-5387un", .data = &board_AR5387un, }, + { .compatible = "d-link,dsl-274xb-f", .data = &board_dsl_274xb_f1, }, ++ { .compatible = "sagem,f@st2704v2", .data = &board_FAST2704V2, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6338 + { .compatible = "brcm,bcm96338gw", .data = &board_96338gw, }, diff --git a/target/linux/brcm63xx/patches-3.18/537-board_fast2504n.patch b/target/linux/brcm63xx/patches-3.18/537-board_fast2504n.patch new file mode 100644 index 0000000000..1e5aee0f53 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/537-board_fast2504n.patch @@ -0,0 +1,121 @@ +From: Max Staudt <openwrt.max@enpas.org> +Date: Wed, 15 Jan 2014 18:51:13 +0000 +Subject: [PATCH] brcm63xx: F@ST2504n board support (Linux-3.10.26) + +Signed-off-by: Max Staudt <openwrt.max@enpas.org> +--- +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -3457,6 +3457,96 @@ static struct board_info __initdata boar + .devs = nb6_devices, + .num_devs = ARRAY_SIZE(nb6_devices), + }; ++ ++static struct board_info __initdata board_fast2504n = { ++ .name = "F@ST2504n", ++ .expected_cpu_id = 0x6362, ++ ++ .has_uart0 = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "fast2504n:orange:power", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "fast2504n:green:power", ++ .gpio = 10, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "fast2504n:red:internet", ++ .gpio = 26, ++ .active_low = 1, ++ }, ++ { ++ .name = "fast2504n:green:ok", ++ .gpio = 28, ++ .active_low = 1, ++ }, ++ { ++ .name = "fast2504n:orange:ok", ++ .gpio = 29, ++ .active_low = 1, ++ }, ++ { ++ .name = "fast2504n:orange:wlan", ++ .gpio = 30, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 24, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 25, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6362 */ + + /* +@@ -3674,6 +3764,7 @@ static const struct board_info __initcon + + #ifdef CONFIG_BCM63XX_CPU_6362 + &board_nb6, ++ &board_fast2504n, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6368 +@@ -3740,6 +3831,7 @@ static struct of_device_id const bcm963x + { .compatible = "t-com,spw303v", .data = &board_spw303v, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6362 ++ { .compatible = "sagem,f@st2504n", .data = &board_fast2504n, }, + { .compatible = "sfr,nb6-ser-r0", .data = &board_nb6, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6368 diff --git a/target/linux/brcm63xx/patches-3.18/550-alice_gate2_leds.patch b/target/linux/brcm63xx/patches-3.18/550-alice_gate2_leds.patch new file mode 100644 index 0000000000..dbf53b7bf5 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/550-alice_gate2_leds.patch @@ -0,0 +1,102 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -2292,6 +2292,99 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + .has_ehci0 = 1, ++ ++ .leds = { ++ { ++ .name = "AGPF-S0:red:power", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "AGPF-S0:red:service", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:service", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:adsl", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:red:adsl", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:red:wifi", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:wifi", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:internet", ++ .gpio = 25, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:red:internet", ++ .gpio = 24, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:red:usr1", ++ .gpio = 27, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:usr1", ++ .gpio = 26, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:red:usr2", ++ .gpio = 30, ++ .active_low = 1, ++ }, ++ { ++ .name = "AGPF-S0:green:usr2", ++ .gpio = 29, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 37, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, + }; + + static struct board_info __initdata board_DWVS0 = { diff --git a/target/linux/brcm63xx/patches-3.18/551-96348gw_a_leds.patch b/target/linux/brcm63xx/patches-3.18/551-96348gw_a_leds.patch new file mode 100644 index 0000000000..f574148a1f --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/551-96348gw_a_leds.patch @@ -0,0 +1,22 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1757,6 +1757,19 @@ static struct board_info __initdata boar + }, + + .has_ohci0 = 1, ++ ++ .leds = { ++ { ++ .name = "96348GW-A::adsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "96348GW-A::usb", ++ .gpio = 0, ++ .active_low = 1, ++ } ++ }, + }; + + /* NetGear DG834G v4 */ diff --git a/target/linux/brcm63xx/patches-3.18/552-board_96348gw-10_reset_button.patch b/target/linux/brcm63xx/patches-3.18/552-board_96348gw-10_reset_button.patch new file mode 100644 index 0000000000..b32fa93099 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/552-board_96348gw-10_reset_button.patch @@ -0,0 +1,20 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1163,6 +1163,17 @@ static struct board_info __initdata boar + .active_low = 1, + }, + }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 6, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, + }; + + static struct board_info __initdata board_96348gw_11 = { diff --git a/target/linux/brcm63xx/patches-3.18/553-boards_probe_switch.patch b/target/linux/brcm63xx/patches-3.18/553-boards_probe_switch.patch new file mode 100644 index 0000000000..ed7ceb999e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/553-boards_probe_switch.patch @@ -0,0 +1,119 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -789,6 +789,8 @@ static struct board_info __initdata boar + .has_uart0 = 1, + .has_enet0 = 1, + .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -832,6 +834,8 @@ static struct board_info __initdata boar + .has_uart0 = 1, + .has_enet0 = 1, + .enet0 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1119,6 +1123,8 @@ static struct board_info __initdata boar + .use_internal_phy = 1, + }, + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1192,6 +1198,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1470,6 +1478,8 @@ static struct board_info __initdata boar + .use_internal_phy = 1, + }, + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1646,6 +1656,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1721,6 +1733,8 @@ static struct board_info __initdata boar + .use_internal_phy = 1, + }, + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1743,6 +1757,8 @@ static struct board_info __initdata boar + .use_internal_phy = 1, + }, + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -1763,6 +1779,8 @@ static struct board_info __initdata boar + .use_internal_phy = 1, + }, + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -2116,6 +2134,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -2169,6 +2189,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -2310,6 +2332,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, +@@ -2428,6 +2452,8 @@ static struct board_info __initdata boar + }, + + .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, + .force_speed_100 = 1, + .force_duplex_full = 1, + }, diff --git a/target/linux/brcm63xx/patches-3.18/554-board_DWVS0_leds_buttons.patch b/target/linux/brcm63xx/patches-3.18/554-board_DWVS0_leds_buttons.patch new file mode 100644 index 0000000000..fa27a487fd --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/554-board_DWVS0_leds_buttons.patch @@ -0,0 +1,97 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -2460,6 +2460,94 @@ static struct board_info __initdata boar + + .has_ohci0 = 1, + .has_ehci0 = 1, ++ ++ .leds = { ++ { ++ .name = "DWV-S0:red:power", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:power", ++ .gpio = 4, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "DWV-S0:red:internet", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:internet", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:ADSL", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:red:ADSL", ++ .gpio = 12, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:red:wifi", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:VoIP", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:red:VoIP", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:red:ethernet", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:ethernet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:red:USB", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "DWV-S0:green:USB", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 37, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, + }; + + /* D-Link DSL-274xB revison C2/C3 */ diff --git a/target/linux/brcm63xx/patches-3.18/555-board_96318ref.patch b/target/linux/brcm63xx/patches-3.18/555-board_96318ref.patch new file mode 100644 index 0000000000..bf46a1ab7d --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/555-board_96318ref.patch @@ -0,0 +1,106 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -86,6 +86,93 @@ static struct board_info __initdata boar + #endif /* CONFIG_BCM63XX_CPU_3368 */ + + /* ++ * known 6318 boards ++ */ ++#ifdef CONFIG_BCM63XX_CPU_6318 ++static struct board_info __initdata board_96318ref = { ++ .name = "96318REF", ++ .expected_cpu_id = 0x6318, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ ++ .has_usbd = 1, ++ ++ .usbd = { ++ .use_fullspeed = 0, ++ .port_no = 0, ++ }, ++ ++ .has_enetsw = 1, ++ ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "96318REF:red:post-failed", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "96318REF:green:inet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "96318REF:red:inet-fail", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "wps", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++#endif /* CONFIG_BCM63XX_CPU_6318 */ ++ ++/* + * known 6328 boards + */ + #ifdef CONFIG_BCM63XX_CPU_6328 +@@ -3932,6 +4019,9 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_3368 + &board_cvg834g, + #endif ++#ifdef CONFIG_BCM63XX_CPU_6318 ++ &board_96318ref, ++#endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, + &board_AR5381u, diff --git a/target/linux/brcm63xx/patches-3.18/556-board_96318ref_p300.patch b/target/linux/brcm63xx/patches-3.18/556-board_96318ref_p300.patch new file mode 100644 index 0000000000..a4d8be626e --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/556-board_96318ref_p300.patch @@ -0,0 +1,105 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -170,6 +170,94 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_96318ref_p300 = { ++ .name = "96318REF_P300", ++ .expected_cpu_id = 0x6318, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ ++ .has_usbd = 1, ++ ++ .usbd = { ++ .use_fullspeed = 0, ++ .port_no = 0, ++ }, ++ ++ .has_enetsw = 1, ++ ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "96318REF_P300:red:post-failed", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "96318REF_P300:green:inet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "96318REF_P300:red:inet-fail", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "96318REF_P300::usb-pwron", ++ .gpio = 13, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "wps", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6318 */ + + /* +@@ -4021,6 +4109,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_6318 + &board_96318ref, ++ &board_96318ref_p300, + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, diff --git a/target/linux/brcm63xx/patches-3.18/557-board_bcm963269bhr.patch b/target/linux/brcm63xx/patches-3.18/557-board_bcm963269bhr.patch new file mode 100644 index 0000000000..783bb6ac6b --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/557-board_bcm963269bhr.patch @@ -0,0 +1,88 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4101,6 +4101,75 @@ static struct board_info __initdata boar + #endif /* CONFIG_BCM63XX_CPU_6368 */ + + /* ++ * known 63268/63269 boards ++ */ ++#ifdef CONFIG_BCM63XX_CPU_63268 ++static struct board_info __initdata board_963269bhr = { ++ .name = "963269BHR", ++ .expected_cpu_id = 0x63268, ++ ++ .has_uart0 = 1, ++ ++ .has_pci = 1, ++ ++ .has_ehci0 = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "963629BHR:green:usb1", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "963629BHR:green:usb2", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 32, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++#endif /* CONFIG_BCM63XX_CPU_63268 */ ++ ++/* + * all boards + */ + static const struct board_info __initconst *bcm963xx_boards[] = { +@@ -4181,6 +4250,9 @@ static const struct board_info __initcon + &board_96368mvwg, + &board_96368mvngr, + #endif ++#ifdef CONFIG_BCM63XX_CPU_63268 ++ &board_963269bhr, ++#endif + }; + + static struct of_device_id const bcm963xx_boards_dt[] = { diff --git a/target/linux/brcm63xx/patches-3.18/558-board_AR1004G.patch b/target/linux/brcm63xx/patches-3.18/558-board_AR1004G.patch new file mode 100644 index 0000000000..92bb027340 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/558-board_AR1004G.patch @@ -0,0 +1,78 @@ +From: "mexit@o2.pl" <mexit@o2.pl> +Date: Sun, 24 Nov 2013 21:33:38 +0000 +Subject: [PATCH 4/5] brcm63xx: add support for Asmax AR 1004g router + +Support for Asmax AR 1004g router + +Signed-off-by: Adrian Feliks <mexit@o2.pl> +--- +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -1424,6 +1424,51 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_96348gw_10_AR1004G = { ++ .name = "AR1004G", ++ .expected_cpu_id = 0x6348, ++ ++ .has_uart0 = 1, ++ .has_enet1 = 1, ++ .has_pci = 1, ++ ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "AR1004G:green:inet", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "AR1004G:green:power", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "AR1004G:red:power", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + + /* BT Voyager 2110 */ + static struct board_info __initdata board_V2110 = { +@@ -4221,6 +4266,7 @@ static const struct board_info __initcon + &board_96348A_122, + &board_CPVA502plus, + &board_96348W3, ++ &board_96348gw_10_AR1004G, + #endif + + #ifdef CONFIG_BCM63XX_CPU_6358 +@@ -4277,6 +4323,7 @@ static struct of_device_id const bcm963x + { .compatible = "brcm,bcm96345gw2", .data = &board_96345gw2, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6348 ++ { .compatible = "asmax,ar1004g", .data = &board_96348gw_10_AR1004G, }, + { .compatible = "brcm,bcm96348r", .data = &board_96348r, }, + { .compatible = "brcm,bcm96348gw-10", .data = &board_96348gw_10, }, + { .compatible = "brcm,bcm96348gw-11", .data = &board_96348gw_11, }, diff --git a/target/linux/brcm63xx/patches-3.18/559-board_vw6339gu.patch b/target/linux/brcm63xx/patches-3.18/559-board_vw6339gu.patch new file mode 100644 index 0000000000..ebccfc0b0c --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/559-board_vw6339gu.patch @@ -0,0 +1,119 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4212,6 +4212,108 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct board_info __initdata board_vw6339gu = { ++ .name = "VW6339GU", ++ .expected_cpu_id = 0x63268, ++ ++ .has_uart0 = 1, ++ ++ .has_ehci0 = 1, ++ .has_ohci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "LAN2", ++ }, ++ ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "LAN3", ++ }, ++ ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "LAN4", ++ }, ++ ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "LAN1", ++ }, ++ ++ [4] = { ++ .used = 1, ++ .phy_id = 7, ++ .name = "WAN", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "VW6339GU:green:power", ++ .gpio = 1, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:red:power", ++ .gpio = 0, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:green:internet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:red:internet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:green:dsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:green:wps", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "VW6339GU:green:usb", ++ .gpio = 15, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 32, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_63268 */ + + /* +@@ -4298,6 +4400,7 @@ static const struct board_info __initcon + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 + &board_963269bhr, ++ &board_vw6339gu, + #endif + }; + diff --git a/target/linux/brcm63xx/patches-3.18/560-board_963268gu_p300.patch b/target/linux/brcm63xx/patches-3.18/560-board_963268gu_p300.patch new file mode 100644 index 0000000000..026d19519b --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/560-board_963268gu_p300.patch @@ -0,0 +1,142 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4149,6 +4149,131 @@ static struct board_info __initdata boar + * known 63268/63269 boards + */ + #ifdef CONFIG_BCM63XX_CPU_63268 ++static struct board_info __initdata board_963268bu_p300 = { ++ .name = "963268BU_P300", ++ .expected_cpu_id = 0x63268, ++ ++ .has_uart0 = 1, ++ ++ .has_ehci0 = 1, ++ .has_ohci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .has_usbd = 1, ++ ++ .usbd = { ++ .use_fullspeed = 0, ++ .port_no = 0, ++ }, ++ ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 17, ++ .name = "FE1", ++ }, ++ ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "GbE2", ++ }, ++ ++ [4] = { ++ .used = 1, ++ .phy_id = 0, ++ .name = "GbE3", ++ }, ++ ++ [5] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "GbE1", ++ }, ++ ++ [6] = { ++ .used = 1, ++ .phy_id = 24, ++ .name = "GbE4", ++ }, ++ ++ [7] = { ++ .used = 1, ++ .phy_id = 25, ++ .name = "GbE5", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "963268BU_P300:green:power", ++ .gpio = 20, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:red:power", ++ .gpio = 21, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:internet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:red:internet", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:adsl", ++ .gpio = 3, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:wps", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:voip1", ++ .gpio = 4, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:voip2", ++ .gpio = 5, ++ .active_low = 1, ++ }, ++ { ++ .name = "963268BU_P300:green:pots", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 32, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 33, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++}; ++ + static struct board_info __initdata board_963269bhr = { + .name = "963269BHR", + .expected_cpu_id = 0x63268, +@@ -4399,6 +4524,7 @@ static const struct board_info __initcon + &board_96368mvngr, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 ++ &board_963268bu_p300, + &board_963269bhr, + &board_vw6339gu, + #endif diff --git a/target/linux/brcm63xx/patches-3.18/561-board_WAP-5813n.patch b/target/linux/brcm63xx/patches-3.18/561-board_WAP-5813n.patch new file mode 100644 index 0000000000..889b8c8560 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/561-board_WAP-5813n.patch @@ -0,0 +1,144 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -13,6 +13,7 @@ + #include <linux/gpio_keys.h> + #include <linux/input.h> + #include <linux/pci_ids.h> ++#include <linux/platform_data/b53.h> + #include <linux/platform_device.h> + #include <linux/spi/spi.h> + #include <linux/spi/spi_gpio.h> +@@ -4143,6 +4144,117 @@ static struct board_info __initdata boar + .has_ohci0 = 1, + .has_ehci0 = 1, + }; ++ ++static struct b53_platform_data WAP5813n_b53_pdata = { ++ .alias = "eth0", ++}; ++ ++static struct spi_board_info WAP5813n_spi_devices[] = { ++ { ++ .modalias = "b53-switch", ++ .max_speed_hz = 781000, ++ .bus_num = 0, ++ .chip_select = 0, ++ .platform_data = &WAP5813n_b53_pdata, ++ } ++}; ++ ++static struct sprom_fixup __initdata wap5813n_fixups[] = { ++ { .offset = 97, .value = 0xfeed }, ++ { .offset = 98, .value = 0x15d1 }, ++ { .offset = 99, .value = 0xfb0d }, ++ { .offset = 113, .value = 0xfef7 }, ++ { .offset = 114, .value = 0x15f7 }, ++ { .offset = 115, .value = 0xfb1a }, ++}; ++ ++static struct board_info __initdata board_WAP5813n = { ++ .name = "96369R-1231N", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [4] = { ++ .used = 1, ++ .phy_id = 0xff, ++ .bypass_link = 1, ++ .force_speed = 1000, ++ .force_duplex_full = 1, ++ .name = "RGMII", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "WAP-5813n:green:power", ++ .gpio = 22, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "WAP-5813n:red:power", ++ .gpio = 24, ++ }, ++ { ++ .name = "WAP-5813n:green:inet", ++ .gpio = 5, ++ }, ++ { ++ .name = "WAP-5813n:red:inet", ++ .gpio = 31, ++ }, ++ { ++ .name = "WAP-5813n:green:wps", ++ .gpio = 23, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "wlan", ++ .gpio = 32, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 35, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43222, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ .board_fixups = wap5813n_fixups, ++ .num_board_fixups = ARRAY_SIZE(wap5813n_fixups), ++ }, ++ ++ .spis = WAP5813n_spi_devices, ++ .num_spis = ARRAY_SIZE(WAP5813n_spi_devices), ++}; + #endif /* CONFIG_BCM63XX_CPU_6368 */ + + /* +@@ -4522,6 +4634,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6368 + &board_96368mvwg, + &board_96368mvngr, ++ &board_WAP5813n, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 + &board_963268bu_p300, +@@ -4595,6 +4708,7 @@ static struct of_device_id const bcm963x + #ifdef CONFIG_BCM63XX_CPU_6368 + { .compatible = "brcm,bcm96368mvngr", .data = &board_96368mvngr, }, + { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, ++ { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 + { .compatible = "brcm,bcm963268bu_p300", .data = &board_963268bu_p300, }, diff --git a/target/linux/brcm63xx/patches-3.18/562-board_VR-3025u.patch b/target/linux/brcm63xx/patches-3.18/562-board_VR-3025u.patch new file mode 100644 index 0000000000..d640315ea6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/562-board_VR-3025u.patch @@ -0,0 +1,135 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4145,6 +4145,116 @@ static struct board_info __initdata boar + .has_ehci0 = 1, + }; + ++static struct sprom_fixup __initdata vr3025u_fixups[] = { ++ { .offset = 97, .value = 0xfeb3 }, ++ { .offset = 98, .value = 0x1618 }, ++ { .offset = 99, .value = 0xfab0 }, ++ { .offset = 113, .value = 0xfed1 }, ++ { .offset = 114, .value = 0x1609 }, ++ { .offset = 115, .value = 0xfad9 }, ++}; ++ ++static struct board_info __initdata board_VR3025u = { ++ .name = "96368M-1541N", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "VR-3025u:green:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025u:green:inet", ++ .gpio = 5, ++ }, ++ { ++ .name = "VR-3025u:green:lan1", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025u:green:lan2", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025u:green:lan3", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025u:green:lan4", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025u:green:power", ++ .gpio = 22, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "VR-3025u:red:power", ++ .gpio = 24, ++ }, ++ { ++ .name = "VR-3025u:red:inet", ++ .gpio = 31, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43222, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ .board_fixups = vr3025u_fixups, ++ .num_board_fixups = ARRAY_SIZE(vr3025u_fixups), ++ }, ++}; ++ + static struct b53_platform_data WAP5813n_b53_pdata = { + .alias = "eth0", + }; +@@ -4634,6 +4744,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6368 + &board_96368mvwg, + &board_96368mvngr, ++ &board_VR3025u, + &board_WAP5813n, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 +@@ -4708,6 +4819,7 @@ static struct of_device_id const bcm963x + #ifdef CONFIG_BCM63XX_CPU_6368 + { .compatible = "brcm,bcm96368mvngr", .data = &board_96368mvngr, }, + { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, ++ { .compatible = "comtrend,vr-3025u", .data = &board_VR3025u, }, + { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 diff --git a/target/linux/brcm63xx/patches-3.18/563-board_VR-3025un.patch b/target/linux/brcm63xx/patches-3.18/563-board_VR-3025un.patch new file mode 100644 index 0000000000..5ee9246138 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/563-board_VR-3025un.patch @@ -0,0 +1,135 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4255,6 +4255,116 @@ static struct board_info __initdata boar + }, + }; + ++static struct sprom_fixup __initdata vr3025un_fixups[] = { ++ { .offset = 97, .value = 0xfeb3 }, ++ { .offset = 98, .value = 0x1618 }, ++ { .offset = 99, .value = 0xfab0 }, ++ { .offset = 113, .value = 0xfed1 }, ++ { .offset = 114, .value = 0x1609 }, ++ { .offset = 115, .value = 0xfad9 }, ++}; ++ ++static struct board_info __initdata board_VR3025un = { ++ .name = "96368M-1341N", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "VR-3025un:green:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025un:green:inet", ++ .gpio = 5, ++ }, ++ { ++ .name = "VR-3025un:green:lan1", ++ .gpio = 6, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025un:green:lan2", ++ .gpio = 7, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025un:green:lan3", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025un:green:iptv", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "VR-3025un:green:power", ++ .gpio = 22, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "VR-3025un:red:power", ++ .gpio = 24, ++ }, ++ { ++ .name = "VR-3025un:red:inet", ++ .gpio = 31, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43222, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ .board_fixups = vr3025un_fixups, ++ .num_board_fixups = ARRAY_SIZE(vr3025un_fixups), ++ }, ++}; ++ + static struct b53_platform_data WAP5813n_b53_pdata = { + .alias = "eth0", + }; +@@ -4745,6 +4855,7 @@ static const struct board_info __initcon + &board_96368mvwg, + &board_96368mvngr, + &board_VR3025u, ++ &board_VR3025un, + &board_WAP5813n, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 +@@ -4820,6 +4931,7 @@ static struct of_device_id const bcm963x + { .compatible = "brcm,bcm96368mvngr", .data = &board_96368mvngr, }, + { .compatible = "brcm,bcm96368mvwg", .data = &board_96368mvwg, }, + { .compatible = "comtrend,vr-3025u", .data = &board_VR3025u, }, ++ { .compatible = "comtrend,vr-3025un", .data = &board_VR3025un, }, + { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 diff --git a/target/linux/brcm63xx/patches-3.18/564-board_P870HW-51a_v2.patch b/target/linux/brcm63xx/patches-3.18/564-board_P870HW-51a_v2.patch new file mode 100644 index 0000000000..e5c93f19bd --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/564-board_P870HW-51a_v2.patch @@ -0,0 +1,115 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -4154,6 +4154,96 @@ static struct sprom_fixup __initdata vr3 + { .offset = 115, .value = 0xfad9 }, + }; + ++static struct board_info __initdata board_P870HW51A_V2 = { ++ .name = "P870HW-51a_v2", ++ .expected_cpu_id = 0x6368, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enetsw = 1, ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "port1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "port2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "port3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "port4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "P870HW-51a:green:power", ++ .gpio = 0, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "P870HW-51a:green:dsl", ++ .gpio = 2, ++ .active_low = 1, ++ }, ++ { ++ .name = "P870HW-51a:green:inet", ++ .gpio = 22, ++ .active_low = 1, ++ }, ++ { ++ .name = "P870HW-51a:orange:wps", ++ .gpio = 24, ++ .active_low = 1, ++ }, ++ { ++ .name = "P870HW-51a:red:inet", ++ .gpio = 33, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 35, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ .active_low = 1, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++}; ++ + static struct board_info __initdata board_VR3025u = { + .name = "96368M-1541N", + .expected_cpu_id = 0x6368, +@@ -4854,6 +4944,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6368 + &board_96368mvwg, + &board_96368mvngr, ++ &board_P870HW51A_V2, + &board_VR3025u, + &board_VR3025un, + &board_WAP5813n, +@@ -4933,6 +5024,7 @@ static struct of_device_id const bcm963x + { .compatible = "comtrend,vr-3025u", .data = &board_VR3025u, }, + { .compatible = "comtrend,vr-3025un", .data = &board_VR3025un, }, + { .compatible = "comtrend,wap-5813n", .data = &board_WAP5813n, }, ++ { .compatible = "zyxel,p870hw-51a-v2", .data = &board_P870HW51A_V2, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_63268 + { .compatible = "brcm,bcm963268bu_p300", .data = &board_963268bu_p300, }, diff --git a/target/linux/brcm63xx/patches-3.18/565-board_hw520.patch b/target/linux/brcm63xx/patches-3.18/565-board_hw520.patch new file mode 100644 index 0000000000..c22eadc227 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/565-board_hw520.patch @@ -0,0 +1,75 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -3206,6 +3206,56 @@ static struct board_info __initdata boar + .num_spis = ARRAY_SIZE(ct6373_spi_devices), + }; + ++static struct board_info __initdata board_HW520 = { ++ .name = "HW6358GW_B", ++ .expected_cpu_id = 0x6358, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ ++ .has_enet0 = 1, ++ .enet0 = { ++ .has_phy = 1, ++ .use_internal_phy = 1, ++ }, ++ ++ .has_enet1 = 1, ++ .enet1 = { ++ .has_phy = 1, ++ .phy_id = 0, ++ .force_speed_100 = 1, ++ .force_duplex_full = 1, ++ }, ++ ++ .leds = { ++ { ++ .name = "HW520:green:net", ++ .gpio = 32, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 37, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM4318, ++ .pci_bus = 0, ++ .pci_dev = 1, ++ }, ++}; ++ + static struct board_info __initdata board_HW553 = { + .name = "HW553", + .expected_cpu_id = 0x6358, +@@ -4928,6 +4978,7 @@ static const struct board_info __initcon + &board_nb4_ser_r0, + &board_nb4_fxc_r1, + &board_ct6373_1, ++ &board_HW520, + &board_HW553, + &board_HW556_A, + &board_HW556_B, +@@ -5002,6 +5053,7 @@ static struct of_device_id const bcm963x + { .compatible = "d-link,dsl-274xb-c2", .data = &board_dsl_274xb_rev_c, }, + { .compatible = "d-link,dsl-2650u", .data = &board_96358vw2, }, + { .compatible = "d-link,dva-g3810bn/tl", .data = &board_DVAG3810BN, }, ++ { .compatible = "huawei,hg520v", .data = &board_HW520, }, + { .compatible = "huawei,hg553", .data = &board_HW553, }, + { .compatible = "huawei,hg556a-a", .data = &board_HW556_A, }, + { .compatible = "huawei,hg556a-b", .data = &board_HW556_B, }, diff --git a/target/linux/brcm63xx/patches-3.18/566-board_A4001N.patch b/target/linux/brcm63xx/patches-3.18/566-board_A4001N.patch new file mode 100644 index 0000000000..2873c53f31 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/566-board_A4001N.patch @@ -0,0 +1,114 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -605,6 +605,95 @@ static struct board_info __initdata boar + }, + }; + ++static struct board_info __initdata board_A4001N = { ++ .name = "96328dg2x2", ++ .expected_cpu_id = 0x6328, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ .has_enetsw = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "A4001N:green:power", ++ .gpio = 8, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "A4001N:red:power", ++ .gpio = 4, ++ }, ++ { ++ .name = "A4001N:red:inet", ++ .gpio = 1, ++ }, ++ { ++ .name = "A4001N:green:usb", ++ .gpio = 10, ++ .active_low = 1, ++ }, ++ { ++ .name = "A4001N:green:dsl", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "reset", ++ .gpio = 23, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 24, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43225, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ }, ++}; ++ + static struct board_info __initdata board_A4001N1 = { + .name = "963281T_TEF", + .expected_cpu_id = 0x6328, +@@ -4929,6 +5018,7 @@ static const struct board_info __initcon + &board_AR5381u, + &board_AR5387un, + &board_963281TAN, ++ &board_A4001N, + &board_A4001N1, + &board_dsl_274xb_f1, + &board_FAST2704V2, +@@ -5013,6 +5103,7 @@ static struct of_device_id const bcm963x + { .compatible = "netgear,cvg834g", .data = &board_cvg834g, }, + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 ++ { .compatible = "adb,a4001n", .data = &board_A4001N, }, + { .compatible = "adb,a4001n1", .data = &board_A4001N1, }, + { .compatible = "brcm,bcm963281TAN", .data = &board_963281TAN, }, + { .compatible = "brcm,bcm96328avng", .data = &board_96328avng, }, diff --git a/target/linux/brcm63xx/patches-3.18/567-board_dsl-2751b_e1.patch b/target/linux/brcm63xx/patches-3.18/567-board_dsl-2751b_e1.patch new file mode 100644 index 0000000000..98c4664bf6 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/567-board_dsl-2751b_e1.patch @@ -0,0 +1,152 @@ +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c +@@ -259,6 +259,141 @@ static struct board_info __initdata boar + }, + }, + }; ++ ++static struct sprom_fixup __initdata dsl2751b_e1_fixups[] = { ++ { .offset = 96, .value = 0x2046 }, ++ { .offset = 97, .value = 0xfe9d }, ++ { .offset = 98, .value = 0x1854 }, ++ { .offset = 99, .value = 0xfa59 }, ++ { .offset = 112, .value = 0x2046 }, ++ { .offset = 113, .value = 0xfe79 }, ++ { .offset = 114, .value = 0x17f5 }, ++ { .offset = 115, .value = 0xfa47 }, ++ { .offset = 161, .value = 0x2222 }, ++ { .offset = 162, .value = 0x2222 }, ++ { .offset = 169, .value = 0x2222 }, ++ { .offset = 170, .value = 0x2222 }, ++ { .offset = 171, .value = 0x5555 }, ++ { .offset = 172, .value = 0x5555 }, ++ { .offset = 173, .value = 0x4444 }, ++ { .offset = 174, .value = 0x4444 }, ++ { .offset = 175, .value = 0x5555 }, ++ { .offset = 176, .value = 0x5555 }, ++}; ++ ++static struct board_info __initdata board_dsl_2751b_d1 = { ++ .name = "AW5200B", ++ .expected_cpu_id = 0x6318, ++ ++ .has_uart0 = 1, ++ .has_pci = 1, ++ .use_fallback_sprom = 1, ++ ++ .has_enetsw = 1, ++ ++ .has_ohci0 = 1, ++ .has_ehci0 = 1, ++ .num_usbh_ports = 1, ++ ++ .enetsw = { ++ .used_ports = { ++ [0] = { ++ .used = 1, ++ .phy_id = 1, ++ .name = "Port 1", ++ }, ++ [1] = { ++ .used = 1, ++ .phy_id = 2, ++ .name = "Port 2", ++ }, ++ [2] = { ++ .used = 1, ++ .phy_id = 3, ++ .name = "Port 3", ++ }, ++ [3] = { ++ .used = 1, ++ .phy_id = 4, ++ .name = "Port 4", ++ }, ++ }, ++ }, ++ ++ .leds = { ++ { ++ .name = "dsl-275xb:green:power", ++ .gpio = 3, ++ .active_low = 1, ++ .default_trigger = "default-on", ++ }, ++ { ++ .name = "dsl-275xb:green:inet", ++ .gpio = 8, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-275xb:red:inet-fail", ++ .gpio = 9, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-275xb:red:post-failed", ++ .gpio = 11, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-275xb:wps:blue", ++ .gpio = 16, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-275xb:green:dsl", ++ .gpio = 17, ++ .active_low = 1, ++ }, ++ { ++ .name = "dsl-275xb:green:usb", ++ .gpio = 49, /* FIXME: does not work! */ ++ .active_low = 1, ++ }, ++ }, ++ ++ .buttons = { ++ { ++ .desc = "wlan", ++ .gpio = 2, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WLAN, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "wps", ++ .gpio = 33, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_WPS_BUTTON, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ { ++ .desc = "reset", ++ .gpio = 34, ++ .active_low = 1, ++ .type = EV_KEY, ++ .code = KEY_RESTART, ++ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL, ++ }, ++ }, ++ ++ .fallback_sprom = { ++ .type = SPROM_BCM43217, ++ .pci_bus = 1, ++ .pci_dev = 0, ++ .board_fixups = dsl2751b_e1_fixups, ++ .num_board_fixups = ARRAY_SIZE(dsl2751b_e1_fixups), ++ }, ++}; + #endif /* CONFIG_BCM63XX_CPU_6318 */ + + /* +@@ -5012,6 +5147,7 @@ static const struct board_info __initcon + #ifdef CONFIG_BCM63XX_CPU_6318 + &board_96318ref, + &board_96318ref_p300, ++ &board_dsl_2751b_d1, + #endif + #ifdef CONFIG_BCM63XX_CPU_6328 + &board_96328avng, diff --git a/target/linux/brcm63xx/patches-3.18/800-wl_exports.patch b/target/linux/brcm63xx/patches-3.18/800-wl_exports.patch new file mode 100644 index 0000000000..68d37c7506 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/800-wl_exports.patch @@ -0,0 +1,25 @@ +--- a/arch/mips/bcm63xx/nvram.c ++++ b/arch/mips/bcm63xx/nvram.c +@@ -40,6 +40,12 @@ struct bcm963xx_nvram { + static struct bcm963xx_nvram nvram; + static int mac_addr_used; + ++/* ++ * Required export for WL ++ */ ++u32 nvram_buf[5] = { 0, cpu_to_le32(20), 0, 0, 0 }; ++EXPORT_SYMBOL(nvram_buf); ++ + void __init bcm63xx_nvram_init(void *addr) + { + unsigned int check_len; +--- a/arch/mips/mm/cache.c ++++ b/arch/mips/mm/cache.c +@@ -59,6 +59,7 @@ void (*_dma_cache_wback)(unsigned long s + void (*_dma_cache_inv)(unsigned long start, unsigned long size); + + EXPORT_SYMBOL(_dma_cache_wback_inv); ++EXPORT_SYMBOL(_dma_cache_inv); + + #endif /* CONFIG_DMA_NONCOHERENT || CONFIG_DMA_MAYBE_COHERENT */ + diff --git a/target/linux/brcm63xx/patches-3.18/801-ssb_export_fallback_sprom.patch b/target/linux/brcm63xx/patches-3.18/801-ssb_export_fallback_sprom.patch new file mode 100644 index 0000000000..11a83536b7 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/801-ssb_export_fallback_sprom.patch @@ -0,0 +1,31 @@ +--- a/arch/mips/bcm63xx/sprom.c ++++ b/arch/mips/bcm63xx/sprom.c +@@ -8,6 +8,7 @@ + */ + + #include <linux/init.h> ++#include <linux/export.h> + #include <linux/kernel.h> + #include <linux/string.h> + #include <linux/platform_device.h> +@@ -387,7 +388,19 @@ struct fallback_sprom_match { + struct ssb_sprom sprom; + }; + +-static struct fallback_sprom_match fallback_sprom; ++struct fallback_sprom_match fallback_sprom; ++ ++int bcm63xx_get_fallback_sprom(uint pci_bus, uint pci_slot, struct ssb_sprom *out) ++{ ++ if (pci_bus != fallback_sprom.pci_bus || ++ pci_slot != fallback_sprom.pci_dev) ++ pr_warn("fallback_sprom: pci bus/device num mismatch: expected %i/%i, but got %i/%i\n", ++ fallback_sprom.pci_bus, fallback_sprom.pci_dev, ++ pci_bus, pci_slot); ++ memcpy(out, &fallback_sprom.sprom, sizeof(struct ssb_sprom)); ++ return 0; ++} ++EXPORT_SYMBOL(bcm63xx_get_fallback_sprom); + + #if defined(CONFIG_SSB_PCIHOST) + int bcm63xx_get_fallback_ssb_sprom(struct ssb_bus *bus, struct ssb_sprom *out) diff --git a/target/linux/brcm63xx/patches-3.18/802-rtl8367r_fix_RGMII_support.patch b/target/linux/brcm63xx/patches-3.18/802-rtl8367r_fix_RGMII_support.patch new file mode 100644 index 0000000000..9037d8954a --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/802-rtl8367r_fix_RGMII_support.patch @@ -0,0 +1,30 @@ +From e3208e6087642b95a5bab3101fc9c6e34892c861 Mon Sep 17 00:00:00 2001 +From: Miguel GAIO <miguel.gaio@efixo.com> +Date: Fri, 6 Jul 2012 14:12:33 +0200 +Subject: [PATCH 6/8] * [rtl8367r] Fix RGMII support + +--- + drivers/net/phy/rtl8367.c | 5 +++++ + 1 files changed, 5 insertions(+), 0 deletions(-) + +--- a/drivers/net/phy/rtl8367.c ++++ b/drivers/net/phy/rtl8367.c +@@ -146,6 +146,10 @@ + #define RTL8367_EXT_RGMXF_TXDELAY_MASK 1 + #define RTL8367_EXT_RGMXF_RXDELAY_MASK 0x7 + ++#define RTL8367_PHY_AD_REG 0x130f ++#define RTL8370_PHY_AD_DUMMY_1_OFFSET 5 ++#define RTL8370_PHY_AD_DUMMY_1_MASK 0xe0 ++ + #define RTL8367_DI_FORCE_REG(_x) (0x1310 + (_x)) + #define RTL8367_DI_FORCE_MODE BIT(12) + #define RTL8367_DI_FORCE_NWAY BIT(7) +@@ -894,6 +898,7 @@ static int rtl8367_extif_set_mode(struct + case RTL8367_EXTIF_MODE_RGMII_33V: + REG_WR(smi, RTL8367_CHIP_DEBUG0_REG, 0x0367); + REG_WR(smi, RTL8367_CHIP_DEBUG1_REG, 0x7777); ++ REG_RMW(smi, RTL8367_PHY_AD_REG, BIT(5), 0); + break; + + case RTL8367_EXTIF_MODE_TMII_MAC: diff --git a/target/linux/brcm63xx/patches-3.18/803-jffs2-work-around-unaligned-accesses-failing-on-bcm6.patch b/target/linux/brcm63xx/patches-3.18/803-jffs2-work-around-unaligned-accesses-failing-on-bcm6.patch new file mode 100644 index 0000000000..8b603e8b66 --- /dev/null +++ b/target/linux/brcm63xx/patches-3.18/803-jffs2-work-around-unaligned-accesses-failing-on-bcm6.patch @@ -0,0 +1,26 @@ +From ff3409ab17d56450943364ba49a16960e3cdda9b Mon Sep 17 00:00:00 2001 +From: Jonas Gorski <jogo@openwrt.org> +Date: Sun, 6 Apr 2014 22:33:16 +0200 +Subject: [RFC] jffs2: work around unaligned accesses failing on bcm63xx/smp + +Unligned memcpy_fromio randomly fails with an unaligned dst. Work around +it by ensuring we are always doing aligned copies. + +Should fix filename corruption in jffs2 with SMP. + +Signed-off-by: Jonas Gorski <jogo@openwrt.org> +--- + fs/jffs2/nodelist.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/fs/jffs2/nodelist.h ++++ b/fs/jffs2/nodelist.h +@@ -255,7 +255,7 @@ struct jffs2_full_dirent + uint32_t ino; /* == zero for unlink */ + unsigned int nhash; + unsigned char type; +- unsigned char name[0]; ++ unsigned char name[0] __attribute__((aligned((sizeof(long))))); + }; + + /* |