diff options
Diffstat (limited to 'target')
20 files changed, 1994 insertions, 0 deletions
diff --git a/target/linux/bmips/config-5.10 b/target/linux/bmips/config-5.10 index e2fc405c57..253b528ffd 100644 --- a/target/linux/bmips/config-5.10 +++ b/target/linux/bmips/config-5.10 @@ -16,6 +16,17 @@ CONFIG_BCM63XX_POWER=y CONFIG_BCM7038_L1_IRQ=y CONFIG_BCM7038_WDT=y CONFIG_BCM7120_L2_IRQ=y +CONFIG_BCMA=y +CONFIG_BCMA_BLOCKIO=y +# CONFIG_BCMA_DEBUG is not set +# CONFIG_BCMA_DRIVER_GMAC_CMN is not set +# CONFIG_BCMA_DRIVER_MIPS is not set +CONFIG_BCMA_DRIVER_PCI=y +# CONFIG_BCMA_DRIVER_PCI_HOSTMODE is not set +CONFIG_BCMA_HOST_PCI=y +CONFIG_BCMA_HOST_PCI_POSSIBLE=y +# CONFIG_BCMA_HOST_SOC is not set +CONFIG_BLK_MQ_PCI=y CONFIG_BLK_PM=y CONFIG_BMIPS_GENERIC=y CONFIG_BOARD_SCACHE=y @@ -139,6 +150,7 @@ CONFIG_MDIO_BUS=y CONFIG_MDIO_BUS_MUX=y CONFIG_MDIO_BUS_MUX_BCM6368=y CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y CONFIG_MEMFD_CREATE=y CONFIG_MFD_SYSCON=y CONFIG_MIGRATION=y @@ -194,6 +206,13 @@ CONFIG_OF_KOBJ=y CONFIG_OF_MDIO=y CONFIG_OF_NET=y CONFIG_PADATA=y +CONFIG_PCI=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIE_BCM6318=y +CONFIG_PCIE_BCM6328=y +CONFIG_PCIE_PME=y +CONFIG_PCI_BCM6348=y +CONFIG_PCI_DOMAINS=y CONFIG_PCI_DRIVERS_LEGACY=y CONFIG_PERF_USE_VMALLOC=y CONFIG_PGTABLE_LEVELS=2 @@ -244,6 +263,15 @@ CONFIG_SPI_BCM63XX_HSSPI=y CONFIG_SPI_MASTER=y CONFIG_SPI_MEM=y CONFIG_SRCU=y +CONFIG_SSB=y +CONFIG_SSB_B43_PCI_BRIDGE=y +CONFIG_SSB_BLOCKIO=y +# CONFIG_SSB_DRIVER_MIPS is not set +CONFIG_SSB_DRIVER_PCICORE=y +CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y +CONFIG_SSB_PCIHOST=y +CONFIG_SSB_PCIHOST_POSSIBLE=y +CONFIG_SSB_SPROM=y CONFIG_SWAP_IO_SPACE=y CONFIG_SWPHY=y CONFIG_SYNC_R4K=y diff --git a/target/linux/bmips/dts/bcm6318-comtrend-ar-5315u.dts b/target/linux/bmips/dts/bcm6318-comtrend-ar-5315u.dts index a5ae435a3a..5b44b05e70 100644 --- a/target/linux/bmips/dts/bcm6318-comtrend-ar-5315u.dts +++ b/target/linux/bmips/dts/bcm6318-comtrend-ar-5315u.dts @@ -164,6 +164,10 @@ status = "okay"; }; +&pcie { + status = "okay"; +}; + &pinctrl { pinctrl_leds: leds { function = "led"; diff --git a/target/linux/bmips/dts/bcm6318.dtsi b/target/linux/bmips/dts/bcm6318.dtsi index e7dc38e937..9067db952e 100644 --- a/target/linux/bmips/dts/bcm6318.dtsi +++ b/target/linux/bmips/dts/bcm6318.dtsi @@ -347,6 +347,41 @@ status = "disabled"; }; + pcie: pcie@10010000 { + compatible = "brcm,bcm6318-pcie"; + reg = <0x10010000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x10200000 0x10200000 0 0x100000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM6318_IRQ_PCIE_RC>; + + clocks = <&periph_clk BCM6318_CLK_PCIE>, + <&periph_clk BCM6318_CLK_PCIE25>, + <&ubus_clk BCM6318_UCLK_PCIE>; + clock-names = "pcie", + "pcie25", + "pcie-ubus"; + + resets = <&periph_rst BCM6318_RST_PCIE>, + <&periph_rst BCM6318_RST_PCIE_EXT>, + <&periph_rst BCM6318_RST_PCIE_CORE>, + <&periph_rst BCM6318_RST_PCIE_HARD>; + reset-names = "pcie", + "pcie-ext", + "pcie-core", + "pcie-hard"; + + power-domains = <&periph_pwr BCM6318_POWER_DOMAIN_PCIE>; + + status = "disabled"; + }; + switch0: switch@10080000 { #address-cells = <1>; #size-cells = <0>; diff --git a/target/linux/bmips/dts/bcm63268.dtsi b/target/linux/bmips/dts/bcm63268.dtsi index 284d2c8ef0..32cbbd7200 100644 --- a/target/linux/bmips/dts/bcm63268.dtsi +++ b/target/linux/bmips/dts/bcm63268.dtsi @@ -371,6 +371,12 @@ status = "disabled"; }; + serdes_cntl: syscon@10001804 { + compatible = "syscon"; + reg = <0x10001804 0x4>; + native-endian; + }; + periph_pwr: power-controller@1000184c { compatible = "brcm,bcm63268-power-controller"; reg = <0x1000184c 0x4>; @@ -468,6 +474,39 @@ status = "disabled"; }; + pcie: pcie@106e0000 { + compatible = "brcm,bcm6328-pcie"; + reg = <0x106e0000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x11000000 0x11000000 0 0xf00000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM63268_IRQ_PCIE_RC>; + + clocks = <&periph_clk BCM63268_CLK_PCIE>; + clock-names = "pcie"; + + resets = <&periph_rst BCM63268_RST_PCIE>, + <&periph_rst BCM63268_RST_PCIE_EXT>, + <&periph_rst BCM63268_RST_PCIE_CORE>, + <&periph_rst BCM63268_RST_PCIE_HARD>; + reset-names = "pcie", + "pcie-ext", + "pcie-core", + "pcie-hard"; + + power-domains = <&periph_pwr BCM63268_POWER_DOMAIN_PCIE>; + + brcm,serdes = <&serdes_cntl>; + + status = "disabled"; + }; + switch0: switch@10700000 { #address-cells = <1>; #size-cells = <0>; diff --git a/target/linux/bmips/dts/bcm6328-comtrend-ar-5387un.dts b/target/linux/bmips/dts/bcm6328-comtrend-ar-5387un.dts index 9ebd6c5c4d..261162454f 100644 --- a/target/linux/bmips/dts/bcm6328-comtrend-ar-5387un.dts +++ b/target/linux/bmips/dts/bcm6328-comtrend-ar-5387un.dts @@ -111,6 +111,10 @@ status = "okay"; }; +&pcie { + status = "okay"; +}; + &pinctrl { pinctrl_leds: leds { function = "led"; diff --git a/target/linux/bmips/dts/bcm6328.dtsi b/target/linux/bmips/dts/bcm6328.dtsi index 64fd04142c..76d7a257d4 100644 --- a/target/linux/bmips/dts/bcm6328.dtsi +++ b/target/linux/bmips/dts/bcm6328.dtsi @@ -317,6 +317,12 @@ status = "disabled"; }; + serdes_cntl: syscon@10001800 { + compatible = "syscon"; + reg = <0x10001800 0x4>; + native-endian; + }; + periph_pwr: power-controller@10001848 { compatible = "brcm,bcm6328-power-controller"; reg = <0x10001848 0x4>; @@ -462,5 +468,38 @@ reg = <1>; }; }; + + pcie: pcie@10e40000 { + compatible = "brcm,bcm6328-pcie"; + reg = <0x10e40000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x10f00000 0x10f00000 0 0x100000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM6328_IRQ_PCIE_RC>; + + clocks = <&periph_clk BCM6328_CLK_PCIE>; + clock-names = "pcie"; + + resets = <&periph_rst BCM6328_RST_PCIE>, + <&periph_rst BCM6328_RST_PCIE_EXT>, + <&periph_rst BCM6328_RST_PCIE_CORE>, + <&periph_rst BCM6328_RST_PCIE_HARD>; + reset-names = "pcie", + "pcie-ext", + "pcie-core", + "pcie-hard"; + + power-domains = <&periph_pwr BCM6328_POWER_DOMAIN_PCIE>; + + brcm,serdes = <&serdes_cntl>; + + status = "disabled"; + }; }; }; diff --git a/target/linux/bmips/dts/bcm6358-huawei-hg556a-b.dts b/target/linux/bmips/dts/bcm6358-huawei-hg556a-b.dts index ba776caf78..0f21ca4a6b 100644 --- a/target/linux/bmips/dts/bcm6358-huawei-hg556a-b.dts +++ b/target/linux/bmips/dts/bcm6358-huawei-hg556a-b.dts @@ -129,6 +129,10 @@ status = "okay"; }; +&pci { + status = "okay"; +}; + &pflash { status = "okay"; diff --git a/target/linux/bmips/dts/bcm6358.dtsi b/target/linux/bmips/dts/bcm6358.dtsi index c06001c62d..fee9850059 100644 --- a/target/linux/bmips/dts/bcm6358.dtsi +++ b/target/linux/bmips/dts/bcm6358.dtsi @@ -280,6 +280,31 @@ status = "disabled"; }; + pci: pci@fffe1000 { + compatible = "brcm,bcm6348-pci"; + reg = <0xfffe1000 0x200>, + <0x08000000 0x10000>; + reg-names = "pci", + "pci-io"; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x30000000 0x30000000 0 0x8000000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM6358_IRQ_MPI>; + + resets = <&periph_rst BCM6358_RST_MPI>; + reset-names = "pci"; + + brcm,remap; + + status = "disabled"; + }; + ehci: usb@fffe1300 { compatible = "brcm,bcm6358-ehci", "generic-ehci"; reg = <0xfffe1300 0x100>; diff --git a/target/linux/bmips/dts/bcm6362-netgear-dgnd3700-v2.dts b/target/linux/bmips/dts/bcm6362-netgear-dgnd3700-v2.dts index 0d88169184..3ad37fed71 100644 --- a/target/linux/bmips/dts/bcm6362-netgear-dgnd3700-v2.dts +++ b/target/linux/bmips/dts/bcm6362-netgear-dgnd3700-v2.dts @@ -209,6 +209,10 @@ status = "okay"; }; +&pcie { + status = "okay"; +}; + &pinctrl { pinctrl_leds: leds { function = "led"; diff --git a/target/linux/bmips/dts/bcm6362.dtsi b/target/linux/bmips/dts/bcm6362.dtsi index 9a3d9c1f66..1ae1522287 100644 --- a/target/linux/bmips/dts/bcm6362.dtsi +++ b/target/linux/bmips/dts/bcm6362.dtsi @@ -406,6 +406,12 @@ status = "disabled"; }; + serdes_cntl: syscon@10001804 { + compatible = "syscon"; + reg = <0x10001804 0x4>; + native-endian; + }; + periph_pwr: power-controller@10001848 { compatible = "brcm,bcm6362-power-controller"; reg = <0x10001848 0x4>; @@ -559,5 +565,36 @@ reg = <1>; }; }; + + pcie: pcie@10e40000 { + compatible = "brcm,bcm6328-pcie"; + reg = <0x10e40000 0x10000>; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x10f00000 0x10f00000 0 0x100000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM6362_IRQ_PCIE_RC>; + + clocks = <&periph_clk BCM6362_CLK_PCIE>; + clock-names = "pcie"; + + resets = <&periph_rst BCM6362_RST_PCIE>, + <&periph_rst BCM6362_RST_PCIE_EXT>, + <&periph_rst BCM6362_RST_PCIE_CORE>; + reset-names = "pcie", + "pcie-ext", + "pcie-core"; + + power-domains = <&periph_pwr BCM6362_POWER_DOMAIN_PCIE>; + + brcm,serdes = <&serdes_cntl>; + + status = "disabled"; + }; }; }; diff --git a/target/linux/bmips/dts/bcm6368-comtrend-vr-3025u.dts b/target/linux/bmips/dts/bcm6368-comtrend-vr-3025u.dts index b597a05f3a..c036b1cbec 100644 --- a/target/linux/bmips/dts/bcm6368-comtrend-vr-3025u.dts +++ b/target/linux/bmips/dts/bcm6368-comtrend-vr-3025u.dts @@ -69,6 +69,10 @@ status = "okay"; }; +&pci { + status = "okay"; +}; + &pflash { status = "okay"; diff --git a/target/linux/bmips/dts/bcm6368.dtsi b/target/linux/bmips/dts/bcm6368.dtsi index 5b5064b29e..9f59182517 100644 --- a/target/linux/bmips/dts/bcm6368.dtsi +++ b/target/linux/bmips/dts/bcm6368.dtsi @@ -414,6 +414,34 @@ status = "disabled"; }; + pci: pci@10001000 { + compatible = "brcm,bcm6348-pci"; + reg = <0x10001000 0x200>, + <0x08000000 0x10000>; + reg-names = "pci", + "pci-io"; + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + bus-range = <0x00 0x01>; + ranges = <0x2000000 0 0x30000000 0x30000000 0 0x8000000>; + linux,pci-probe-only = <1>; + + interrupt-parent = <&periph_intc>; + interrupts = <BCM6368_IRQ_MPI>; + + resets = <&periph_rst BCM6368_RST_MPI>; + reset-names = "pci"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pci>; + + brcm,remap; + + status = "disabled"; + }; + ehci: usb@10001500 { compatible = "brcm,bcm6368-ehci", "generic-ehci"; reg = <0x10001500 0x100>; diff --git a/target/linux/bmips/files/arch/mips/pci/fixup-bmips.c b/target/linux/bmips/files/arch/mips/pci/fixup-bmips.c new file mode 100644 index 0000000000..34050407c4 --- /dev/null +++ b/target/linux/bmips/files/arch/mips/pci/fixup-bmips.c @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com> + */ + +#include <linux/pci.h> + +int bmips_pci_irq = -1; + +int pcibios_plat_dev_init(struct pci_dev *pci_dev) +{ + return PCIBIOS_SUCCESSFUL; +} + +int pcibios_map_irq(const struct pci_dev *pci_dev, u8 slot, u8 pin) +{ + return bmips_pci_irq; +} diff --git a/target/linux/bmips/files/drivers/pci/controller/pci-bcm6348.c b/target/linux/bmips/files/drivers/pci/controller/pci-bcm6348.c new file mode 100644 index 0000000000..c1d3bde5df --- /dev/null +++ b/target/linux/bmips/files/drivers/pci/controller/pci-bcm6348.c @@ -0,0 +1,825 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * BCM6348 PCI Controller Driver + * + * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com> + * Copyright (C) 2015 Jonas Gorski <jonas.gorski@gmail.com> + * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> + */ + +#include <linux/clk.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/kernel.h> +#include <linux/memblock.h> +#include <linux/mm.h> +#include <linux/of_address.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> +#include <linux/of_platform.h> +#include <linux/pci.h> +#include <linux/reset.h> +#include <linux/types.h> +#include <linux/vmalloc.h> + +#include "../pci.h" + +#define CARDBUS_DUMMY_ID 0x6348 +#define CARDBUS_PCI_IDSEL 0x8 +#define FAKE_CB_BRIDGE_SLOT 0x1e + +#define BCMPCI_REG_TIMERS 0x40 +#define REG_TIMER_TRDY_SHIFT 0 +#define REG_TIMER_TRDY_MASK (0xff << REG_TIMER_TRDY_SHIFT) +#define REG_TIMER_RETRY_SHIFT 8 +#define REG_TIMER_RETRY_MASK (0xff << REG_TIMER_RETRY_SHIFT) + +#define MPI_SP0_RANGE_REG 0x100 +#define MPI_SP0_REMAP_REG 0x104 +#define MPI_SP0_REMAP_ENABLE_MASK (1 << 0) +#define MPI_SP1_RANGE_REG 0x10C +#define MPI_SP1_REMAP_REG 0x110 +#define MPI_SP1_REMAP_ENABLE_MASK (1 << 0) + +#define MPI_L2PCFG_REG 0x11c +#define MPI_L2PCFG_CFG_TYPE_SHIFT 0 +#define MPI_L2PCFG_CFG_TYPE_MASK (0x3 << MPI_L2PCFG_CFG_TYPE_SHIFT) +#define MPI_L2PCFG_REG_SHIFT 2 +#define MPI_L2PCFG_REG_MASK (0x3f << MPI_L2PCFG_REG_SHIFT) +#define MPI_L2PCFG_FUNC_SHIFT 8 +#define MPI_L2PCFG_FUNC_MASK (0x7 << MPI_L2PCFG_FUNC_SHIFT) +#define MPI_L2PCFG_DEVNUM_SHIFT 11 +#define MPI_L2PCFG_DEVNUM_MASK (0x1f << MPI_L2PCFG_DEVNUM_SHIFT) +#define MPI_L2PCFG_CFG_USEREG_MASK (1 << 30) +#define MPI_L2PCFG_CFG_SEL_MASK (1 << 31) + +#define MPI_L2PMEMRANGE1_REG 0x120 +#define MPI_L2PMEMBASE1_REG 0x124 +#define MPI_L2PMEMREMAP1_REG 0x128 +#define MPI_L2PMEMRANGE2_REG 0x12C +#define MPI_L2PMEMBASE2_REG 0x130 +#define MPI_L2PMEMREMAP2_REG 0x134 +#define MPI_L2PIORANGE_REG 0x138 +#define MPI_L2PIOBASE_REG 0x13C +#define MPI_L2PIOREMAP_REG 0x140 +#define MPI_L2P_BASE_MASK (0xffff8000) +#define MPI_L2PREMAP_ENABLED_MASK (1 << 0) +#define MPI_L2PREMAP_IS_CARDBUS_MASK (1 << 2) + +#define MPI_PCIMODESEL_REG 0x144 +#define MPI_PCIMODESEL_BAR1_NOSWAP_MASK (1 << 0) +#define MPI_PCIMODESEL_BAR2_NOSWAP_MASK (1 << 1) +#define MPI_PCIMODESEL_EXT_ARB_MASK (1 << 2) +#define MPI_PCIMODESEL_PREFETCH_SHIFT 4 +#define MPI_PCIMODESEL_PREFETCH_MASK (0xf << MPI_PCIMODESEL_PREFETCH_SHIFT) + +#define MPI_LOCBUSCTL_REG 0x14c +#define MPI_LOCBUSCTL_EN_PCI_GPIO_MASK (1 << 0) +#define MPI_LOCBUSCTL_U2P_NOSWAP_MASK (1 << 1) + +#define MPI_LOCINT_REG 0x150 +#define MPI_LOCINT_MASK(x) (1 << (x + 16)) +#define MPI_LOCINT_STAT(x) (1 << (x)) +#define MPI_LOCINT_DIR_FAILED 6 +#define MPI_LOCINT_EXT_PCI_INT 7 +#define MPI_LOCINT_SERR 8 +#define MPI_LOCINT_CSERR 9 + +#define MPI_PCICFGCTL_REG 0x178 +#define MPI_PCICFGCTL_CFGADDR_SHIFT 2 +#define MPI_PCICFGCTL_CFGADDR_MASK (0x1f << MPI_PCICFGCTL_CFGADDR_SHIFT) +#define MPI_PCICFGCTL_WRITEEN_MASK (1 << 7) + +#define MPI_PCICFGDATA_REG 0x17c + +#define PCMCIA_OFFSET 0x54 + +#define PCMCIA_C1_REG 0x0 +#define PCMCIA_C1_CD1_MASK (1 << 0) +#define PCMCIA_C1_CD2_MASK (1 << 1) +#define PCMCIA_C1_VS1_MASK (1 << 2) +#define PCMCIA_C1_VS2_MASK (1 << 3) +#define PCMCIA_C1_VS1OE_MASK (1 << 6) +#define PCMCIA_C1_VS2OE_MASK (1 << 7) +#define PCMCIA_C1_CBIDSEL_SHIFT (8) +#define PCMCIA_C1_CBIDSEL_MASK (0x1f << PCMCIA_C1_CBIDSEL_SHIFT) +#define PCMCIA_C1_EN_PCMCIA_GPIO_MASK (1 << 13) +#define PCMCIA_C1_EN_PCMCIA_MASK (1 << 14) +#define PCMCIA_C1_EN_CARDBUS_MASK (1 << 15) +#define PCMCIA_C1_RESET_MASK (1 << 18) + +#ifdef CONFIG_CARDBUS +struct bcm6348_cb { + u16 pci_command; + u8 cb_latency; + u8 subordinate_busn; + u8 cardbus_busn; + u8 pci_busn; + int bus_assigned; + u16 bridge_control; + + u32 mem_base0; + u32 mem_limit0; + u32 mem_base1; + u32 mem_limit1; + + u32 io_base0; + u32 io_limit0; + u32 io_base1; + u32 io_limit1; +}; +#endif /* CONFIG_CARDBUS */ + +struct bcm6348_pci { + void __iomem *pci; + void __iomem *pcmcia; + void __iomem *io; + int irq; + struct reset_control *reset; + bool remap; +#ifdef CONFIG_CARDBUS + struct bcm6348_cb cb; + int cb_bus; +#endif /* CONFIG_CARDBUS */ +}; + +static struct bcm6348_pci bcm6348_pci; + +extern int bmips_pci_irq; + +static u32 bcm6348_int_cfg_readl(u32 reg) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + u32 tmp; + + tmp = reg & MPI_PCICFGCTL_CFGADDR_MASK; + tmp |= MPI_PCICFGCTL_WRITEEN_MASK; + __raw_writel(tmp, priv->pci + MPI_PCICFGCTL_REG); + iob(); + return __raw_readl(priv->pci + MPI_PCICFGDATA_REG); +} + +static void bcm6348_int_cfg_writel(u32 val, u32 reg) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + u32 tmp; + + tmp = reg & MPI_PCICFGCTL_CFGADDR_MASK; + tmp |= MPI_PCICFGCTL_WRITEEN_MASK; + __raw_writel(tmp, priv->pci + MPI_PCICFGCTL_REG); + __raw_writel(val, priv->pci + MPI_PCICFGDATA_REG); +} + +/* + * swizzle 32bits data to return only the needed part + */ +static int postprocess_read(u32 data, int where, unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (data >> ((where & 3) << 3)) & 0xff; + break; + case 2: + ret = (data >> ((where & 3) << 3)) & 0xffff; + break; + case 4: + ret = data; + break; + } + + return ret; +} + +static int preprocess_write(u32 orig_data, u32 val, int where, + unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (orig_data & ~(0xff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 2: + ret = (orig_data & ~(0xffff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 4: + ret = val; + break; + } + + return ret; +} + +static int bcm6348_setup_cfg_access(int type, unsigned int busn, + unsigned int devfn, int where) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + unsigned int slot, func, reg; + u32 val; + + slot = PCI_SLOT(devfn); + func = PCI_FUNC(devfn); + reg = where >> 2; + + /* sanity check */ + if (slot > (MPI_L2PCFG_DEVNUM_MASK >> MPI_L2PCFG_DEVNUM_SHIFT)) + return 1; + + if (func > (MPI_L2PCFG_FUNC_MASK >> MPI_L2PCFG_FUNC_SHIFT)) + return 1; + + if (reg > (MPI_L2PCFG_REG_MASK >> MPI_L2PCFG_REG_SHIFT)) + return 1; + + /* ok, setup config access */ + val = (reg << MPI_L2PCFG_REG_SHIFT); + val |= (func << MPI_L2PCFG_FUNC_SHIFT); + val |= (slot << MPI_L2PCFG_DEVNUM_SHIFT); + val |= MPI_L2PCFG_CFG_USEREG_MASK; + val |= MPI_L2PCFG_CFG_SEL_MASK; + /* type 0 cycle for local bus, type 1 cycle for anything else */ + if (type != 0) { + /* FIXME: how to specify bus ??? */ + val |= (1 << MPI_L2PCFG_CFG_TYPE_SHIFT); + } + __raw_writel(val, priv->pci + MPI_L2PCFG_REG); + + return 0; +} + + +static int bcm6348_do_cfg_read(int type, unsigned int busn, + unsigned int devfn, int where, int size, + u32 *val) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + u32 data; + + /* two phase cycle, first we write address, then read data at + * another location, caller already has a spinlock so no need + * to add one here */ + if (bcm6348_setup_cfg_access(type, busn, devfn, where)) + return PCIBIOS_DEVICE_NOT_FOUND; + iob(); + data = le32_to_cpu(__raw_readl(priv->io)); + /* restore IO space normal behaviour */ + __raw_writel(0, priv->pci + MPI_L2PCFG_REG); + + *val = postprocess_read(data, where, size); + + return PCIBIOS_SUCCESSFUL; +} + +static int bcm6348_do_cfg_write(int type, unsigned int busn, + unsigned int devfn, int where, int size, + u32 val) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + u32 data; + + /* two phase cycle, first we write address, then write data to + * another location, caller already has a spinlock so no need + * to add one here */ + if (bcm6348_setup_cfg_access(type, busn, devfn, where)) + return PCIBIOS_DEVICE_NOT_FOUND; + iob(); + + data = le32_to_cpu(__raw_readl(priv->io)); + data = preprocess_write(data, val, where, size); + + __raw_writel(cpu_to_le32(data), priv->io); + wmb(); + /* no way to know the access is done, we have to wait */ + udelay(500); + /* restore IO space normal behaviour */ + __raw_writel(0, priv->pci + MPI_L2PCFG_REG); + + return PCIBIOS_SUCCESSFUL; +} + +static int bcm6348_pci_read(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + int type; + + type = bus->parent ? 1 : 0; + + if (type == 0 && PCI_SLOT(devfn) == CARDBUS_PCI_IDSEL) + return PCIBIOS_DEVICE_NOT_FOUND; + + return bcm6348_do_cfg_read(type, bus->number, devfn, + where, size, val); +} + +static int bcm6348_pci_write(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 val) +{ + int type; + + type = bus->parent ? 1 : 0; + + if (type == 0 && PCI_SLOT(devfn) == CARDBUS_PCI_IDSEL) + return PCIBIOS_DEVICE_NOT_FOUND; + + return bcm6348_do_cfg_write(type, bus->number, devfn, + where, size, val); +} + +static struct pci_ops bcm6348_pci_ops = { + .read = bcm6348_pci_read, + .write = bcm6348_pci_write, +}; + +static struct resource bcm6348_pci_io_resource = { + .name = "BCM6348 PCI IO space", + .flags = IORESOURCE_IO, +}; +static struct resource bcm6348_pci_mem_resource; +static struct resource bcm6348_pci_busn_resource; + +static struct pci_controller bcm6348_pci_controller = { + .pci_ops = &bcm6348_pci_ops, + .io_resource = &bcm6348_pci_io_resource, + .mem_resource = &bcm6348_pci_mem_resource, + .busn_resource = &bcm6348_pci_busn_resource, +}; + +#ifdef CONFIG_CARDBUS +static int bcm6348_cb_bridge_read(int where, int size, u32 *val) +{ + struct bcm6348_cb *cb = &bcm6348_pci.cb; + unsigned int reg; + u32 data; + + data = 0; + reg = where >> 2; + switch (reg) { + case (PCI_VENDOR_ID >> 2): + case (PCI_CB_SUBSYSTEM_VENDOR_ID >> 2): + /* create dummy vendor/device id from our cpu id */ + data = (CARDBUS_DUMMY_ID << 16) | PCI_VENDOR_ID_BROADCOM; + break; + + case (PCI_COMMAND >> 2): + data = (PCI_STATUS_DEVSEL_SLOW << 16); + data |= cb->pci_command; + break; + + case (PCI_CLASS_REVISION >> 2): + data = (PCI_CLASS_BRIDGE_CARDBUS << 16); + break; + + case (PCI_CACHE_LINE_SIZE >> 2): + data = (PCI_HEADER_TYPE_CARDBUS << 16); + break; + + case (PCI_INTERRUPT_LINE >> 2): + /* bridge control */ + data = (cb->bridge_control << 16); + /* pin:intA line:0xff */ + data |= (0x1 << 8) | 0xff; + break; + + case (PCI_CB_PRIMARY_BUS >> 2): + data = (cb->cb_latency << 24); + data |= (cb->subordinate_busn << 16); + data |= (cb->cardbus_busn << 8); + data |= cb->pci_busn; + break; + + case (PCI_CB_MEMORY_BASE_0 >> 2): + data = cb->mem_base0; + break; + + case (PCI_CB_MEMORY_LIMIT_0 >> 2): + data = cb->mem_limit0; + break; + + case (PCI_CB_MEMORY_BASE_1 >> 2): + data = cb->mem_base1; + break; + + case (PCI_CB_MEMORY_LIMIT_1 >> 2): + data = cb->mem_limit1; + break; + + case (PCI_CB_IO_BASE_0 >> 2): + /* | 1 for 32bits io support */ + data = cb->io_base0 | 0x1; + break; + + case (PCI_CB_IO_LIMIT_0 >> 2): + data = cb->io_limit0; + break; + + case (PCI_CB_IO_BASE_1 >> 2): + /* | 1 for 32bits io support */ + data = cb->io_base1 | 0x1; + break; + + case (PCI_CB_IO_LIMIT_1 >> 2): + data = cb->io_limit1; + break; + } + + *val = postprocess_read(data, where, size); + return PCIBIOS_SUCCESSFUL; +} + +/* + * emulate configuration write access on a cardbus bridge + */ +static int bcm6348_cb_bridge_write(int where, int size, u32 val) +{ + struct bcm6348_cb *cb = &bcm6348_pci.cb; + unsigned int reg; + u32 data, tmp; + int ret; + + ret = bcm6348_cb_bridge_read((where & ~0x3), 4, &data); + if (ret != PCIBIOS_SUCCESSFUL) + return ret; + + data = preprocess_write(data, val, where, size); + + reg = where >> 2; + switch (reg) { + case (PCI_COMMAND >> 2): + cb->pci_command = (data & 0xffff); + break; + + case (PCI_CB_PRIMARY_BUS >> 2): + cb->cb_latency = (data >> 24) & 0xff; + cb->subordinate_busn = (data >> 16) & 0xff; + cb->cardbus_busn = (data >> 8) & 0xff; + cb->pci_busn = data & 0xff; + if (cb->cardbus_busn) + cb->bus_assigned = 1; + break; + + case (PCI_INTERRUPT_LINE >> 2): + tmp = (data >> 16) & 0xffff; + /* Disable memory prefetch support */ + tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM0; + tmp &= ~PCI_CB_BRIDGE_CTL_PREFETCH_MEM1; + cb->bridge_control = tmp; + break; + + case (PCI_CB_MEMORY_BASE_0 >> 2): + cb->mem_base0 = data; + break; + + case (PCI_CB_MEMORY_LIMIT_0 >> 2): + cb->mem_limit0 = data; + break; + + case (PCI_CB_MEMORY_BASE_1 >> 2): + cb->mem_base1 = data; + break; + + case (PCI_CB_MEMORY_LIMIT_1 >> 2): + cb->mem_limit1 = data; + break; + + case (PCI_CB_IO_BASE_0 >> 2): + cb->io_base0 = data; + break; + + case (PCI_CB_IO_LIMIT_0 >> 2): + cb->io_limit0 = data; + break; + + case (PCI_CB_IO_BASE_1 >> 2): + cb->io_base1 = data; + break; + + case (PCI_CB_IO_LIMIT_1 >> 2): + cb->io_limit1 = data; + break; + } + + return PCIBIOS_SUCCESSFUL; +} + +static int bcm6348_cb_read(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + struct bcm6348_cb *cb = &priv->cb; + + /* Snoop access to slot 0x1e on root bus, we fake a cardbus + * bridge at this location */ + if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) { + priv->cb_bus = bus->number; + return bcm6348_cb_bridge_read(where, size, val); + } + + /* A configuration cycle for the device behind the cardbus + * bridge is actually done as a type 0 cycle on the primary + * bus. This means that only one device can be on the cardbus + * bus */ + if (cb->bus_assigned && + bus->number == cb->cardbus_busn && + PCI_SLOT(devfn) == 0) + return bcm6348_do_cfg_read(0, 0, + PCI_DEVFN(CARDBUS_PCI_IDSEL, 0), + where, size, val); + + return PCIBIOS_DEVICE_NOT_FOUND; +} + +static int bcm6348_cb_write(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 val) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + struct bcm6348_cb *cb = &priv->cb; + + if (!bus->parent && PCI_SLOT(devfn) == FAKE_CB_BRIDGE_SLOT) { + priv->cb_bus = bus->number; + return bcm6348_cb_bridge_write(where, size, val); + } + + if (cb->bus_assigned && + bus->number == cb->cardbus_busn && + PCI_SLOT(devfn) == 0) + return bcm6348_do_cfg_write(0, 0, + PCI_DEVFN(CARDBUS_PCI_IDSEL, 0), + where, size, val); + + return PCIBIOS_DEVICE_NOT_FOUND; +} + +static struct pci_ops bcm6348_cb_ops = { + .read = bcm6348_cb_read, + .write = bcm6348_cb_write, +}; + +/* + * only one IO window, so it cannot be shared by PCI and cardbus, use + * fixup to choose and detect unhandled configuration + */ +static void bcm6348_pci_fixup(struct pci_dev *dev) +{ + struct bcm6348_pci *priv = &bcm6348_pci; + struct bcm6348_cb *cb = &priv->cb; + static int io_window = -1; + int i, found, new_io_window; + u32 val; + + /* look for any io resource */ + found = 0; + for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) { + if (pci_resource_flags(dev, i) & IORESOURCE_IO) { + found = 1; + break; + } + } + + if (!found) + return; + + /* skip our fake bus with only cardbus bridge on it */ + if (dev->bus->number == priv->cb_bus) + return; + + /* find on which bus the device is */ + if (cb->bus_assigned && + dev->bus->number == cb->cardbus_busn && + PCI_SLOT(dev->devfn) == 0) + new_io_window = 1; + else + new_io_window = 0; + + if (new_io_window == io_window) + return; + + if (io_window != -1) { + pr_err("bcm63xx: both PCI and cardbus devices " + "need IO, which hardware cannot do\n"); + return; + } + + pr_info("bcm63xx: PCI IO window assigned to %s\n", + (new_io_window == 0) ? "PCI" : "cardbus"); + + val = __raw_readl(priv->pci + MPI_L2PIOREMAP_REG); + if (io_window) + val |= MPI_L2PREMAP_IS_CARDBUS_MASK; + else + val &= ~MPI_L2PREMAP_IS_CARDBUS_MASK; + __raw_writel(val, priv->pci + MPI_L2PIOREMAP_REG); + + io_window = new_io_window; +} +DECLARE_PCI_FIXUP_ENABLE(PCI_ANY_ID, PCI_ANY_ID, bcm6348_pci_fixup); + +static struct resource bcm6348_cb_io_resource = { + .name = "bcm6348 CB IO space", + .flags = IORESOURCE_IO, +}; +static struct resource bcm6348_cb_mem_resource; + +static struct pci_controller bcm6348_cb_controller = { + .pci_ops = &bcm6348_cb_ops, + .io_resource = &bcm6348_cb_io_resource, + .mem_resource = &bcm6348_cb_mem_resource, +}; +#endif /* CONFIG_CARDBUS */ + +static void bcm6348_pci_setup(struct bcm6348_pci *priv) +{ + u32 val; + + /* Setup local bus to PCI access (PCI memory) */ + val = bcm6348_pci_mem_resource.start & MPI_L2P_BASE_MASK; + __raw_writel(val, priv->pci + MPI_L2PMEMBASE1_REG); + __raw_writel(~(resource_size(&bcm6348_pci_mem_resource) - 1), + priv->pci + MPI_L2PMEMRANGE1_REG); + __raw_writel(val | MPI_L2PREMAP_ENABLED_MASK, + priv->pci + MPI_L2PMEMREMAP1_REG); + + /* Set Cardbus IDSEL (type 0 cfg access on primary bus for + * this IDSEL will be done on Cardbus instead) */ + val = __raw_readl(priv->pcmcia + PCMCIA_C1_REG); + val &= ~PCMCIA_C1_CBIDSEL_MASK; + val |= (CARDBUS_PCI_IDSEL << PCMCIA_C1_CBIDSEL_SHIFT); + __raw_writel(val, priv->pcmcia + PCMCIA_C1_REG); + +#ifdef CONFIG_CARDBUS + /* setup local bus to PCI access (Cardbus memory) */ + val = bcm6348_cb_mem_resource.start & MPI_L2P_BASE_MASK; + __raw_writel(val, priv->pci + MPI_L2PMEMBASE2_REG); + __raw_writel(~(resource_size(&bcm6348_cb_mem_resource) - 1), + priv->pci + MPI_L2PMEMRANGE2_REG); + val |= MPI_L2PREMAP_ENABLED_MASK | MPI_L2PREMAP_IS_CARDBUS_MASK; + __raw_writel(val, priv->pci + MPI_L2PMEMREMAP2_REG); +#else + /* disable second access windows */ + __raw_writel(0, priv->pci + MPI_L2PMEMREMAP2_REG); +#endif + + /* setup local bus to PCI access (IO memory), we have only 1 + * IO window for both PCI and cardbus, but it cannot handle + * both at the same time, assume standard PCI for now, if + * cardbus card has IO zone, PCI fixup will change window to + * cardbus */ + val = bcm6348_pci_io_resource.start & MPI_L2P_BASE_MASK; + __raw_writel(val, priv->pci + MPI_L2PIOBASE_REG); + __raw_writel(~(resource_size(&bcm6348_pci_io_resource) - 1), + priv->pci + MPI_L2PIORANGE_REG); + __raw_writel(val | MPI_L2PREMAP_ENABLED_MASK, + priv->pci + MPI_L2PIOREMAP_REG); + + /* Enable PCI related GPIO pins */ + __raw_writel(MPI_LOCBUSCTL_EN_PCI_GPIO_MASK, + priv->pci + MPI_LOCBUSCTL_REG); + + /* Setup PCI to local bus access, used by PCI device to target + * local RAM while bus mastering */ + bcm6348_int_cfg_writel(0, PCI_BASE_ADDRESS_3); + if (priv->remap) + val = MPI_SP0_REMAP_ENABLE_MASK; + else + val = 0; + __raw_writel(val, priv->pci + MPI_SP0_REMAP_REG); + + bcm6348_int_cfg_writel(0, PCI_BASE_ADDRESS_4); + __raw_writel(0, priv->pci + MPI_SP1_REMAP_REG); + + /* Setup sp0 range to local RAM size */ + __raw_writel(~(memblock_phys_mem_size() - 1), + priv->pci + MPI_SP0_RANGE_REG); + __raw_writel(0, priv->pci + MPI_SP1_RANGE_REG); + + /* Change host bridge retry counter to infinite number of + * retries, needed for some broadcom wifi cards with Silicon + * Backplane bus where access to srom seems very slow */ + val = bcm6348_int_cfg_readl(BCMPCI_REG_TIMERS); + val &= ~REG_TIMER_RETRY_MASK; + bcm6348_int_cfg_writel(val, BCMPCI_REG_TIMERS); + + /* EEnable memory decoder and bus mastering */ + val = bcm6348_int_cfg_readl(PCI_COMMAND); + val |= (PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); + bcm6348_int_cfg_writel(val, PCI_COMMAND); + + /* Enable read prefetching & disable byte swapping for bus + * mastering transfers */ + val = __raw_readl(priv->pci + MPI_PCIMODESEL_REG); + val &= ~MPI_PCIMODESEL_BAR1_NOSWAP_MASK; + val &= ~MPI_PCIMODESEL_BAR2_NOSWAP_MASK; + val &= ~MPI_PCIMODESEL_PREFETCH_MASK; + val |= (8 << MPI_PCIMODESEL_PREFETCH_SHIFT); + __raw_writel(val, priv->pci + MPI_PCIMODESEL_REG); + + /* Enable pci interrupt */ + val = __raw_readl(priv->pci + MPI_LOCINT_REG); + val |= MPI_LOCINT_MASK(MPI_LOCINT_EXT_PCI_INT); + __raw_writel(val, priv->pci + MPI_LOCINT_REG); +} + +static int bcm6348_pci_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct bcm6348_pci *priv = &bcm6348_pci; + struct resource *res; + + of_pci_check_probe_only(); + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pci"); + priv->pci = devm_ioremap_resource(dev, res); + if (IS_ERR(priv->pci)) + return PTR_ERR(priv->pci); + + priv->pcmcia = priv->pci + PCMCIA_OFFSET; + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pci-io"); + if (!res) + return -EINVAL; +#ifdef CONFIG_CARDBUS + bcm6348_pci_io_resource.start = res->start; + bcm6348_pci_io_resource.end = res->end - (resource_size(res) >> 1); + bcm6348_cb_io_resource.start = res->start + (resource_size(res) >> 1); + bcm6348_cb_io_resource.end = res->end; +#else + bcm6348_pci_io_resource.start = res->start; + bcm6348_pci_io_resource.end = res->end; +#endif + + priv->irq = platform_get_irq(pdev, 0); + if (!priv->irq) + return -ENODEV; + + bmips_pci_irq = priv->irq; + + priv->reset = devm_reset_control_get(dev, "pci"); + if (IS_ERR(priv->reset)) + return PTR_ERR(priv->reset); + + priv->remap = of_property_read_bool(np, "brcm,remap"); + + reset_control_reset(priv->reset); + + pci_load_of_ranges(&bcm6348_pci_controller, np); + if (!bcm6348_pci_mem_resource.start) + return -EINVAL; + + of_pci_parse_bus_range(np, &bcm6348_pci_busn_resource); + + /* + * Configuration accesses are done through IO space, remap 4 + * first bytes to access it from CPU. + * + * This means that no IO access from CPU should happen while + * we do a configuration cycle, but there's no way we can add + * a spinlock for each io access, so this is currently kind of + * broken on SMP. + */ + priv->io = ioremap(bcm6348_pci_io_resource.start, sizeof(u32)); + if (!priv->io) + return -ENOMEM; + + bcm6348_pci_setup(priv); + + register_pci_controller(&bcm6348_pci_controller); + +#ifdef CONFIG_CARDBUS + priv->cb_bus = -1; + register_pci_controller(&bcm6348_cb_controller); +#endif /* CONFIG_CARDBUS */ + + /* Mark memory space used for IO mapping as reserved */ + request_mem_region(bcm6348_pci_io_resource.start, + resource_size(&bcm6348_pci_io_resource), + "BCM6348 PCI IO space"); + + return 0; +} + +static const struct of_device_id bcm6348_pci_of_match[] = { + { .compatible = "brcm,bcm6348-pci", }, + { /* sentinel */ } +}; + +static struct platform_driver bcm6348_pci_driver = { + .probe = bcm6348_pci_probe, + .driver = { + .name = "bcm6348-pci", + .of_match_table = bcm6348_pci_of_match, + }, +}; + +int __init bcm6348_pci_init(void) +{ + int ret = platform_driver_register(&bcm6348_pci_driver); + if (ret) + pr_err("pci-bcm6348: Error registering platform driver!\n"); + return ret; +} +late_initcall_sync(bcm6348_pci_init); diff --git a/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6318.c b/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6318.c new file mode 100644 index 0000000000..1df67b8389 --- /dev/null +++ b/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6318.c @@ -0,0 +1,402 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * BCM6318 PCIe Controller Driver + * + * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com> + * Copyright (C) 2015 Jonas Gorski <jonas.gorski@gmail.com> + * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> + */ + +#include <linux/clk.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/kernel.h> +#include <linux/mm.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> +#include <linux/of_platform.h> +#include <linux/pci.h> +#include <linux/reset.h> +#include <linux/types.h> +#include <linux/vmalloc.h> + +#include "../pci.h" + +#define PCIE_BUS_BRIDGE 0 +#define PCIE_BUS_DEVICE 1 + +#define PCIE_SPECIFIC_REG 0x188 +#define SPECIFIC_ENDIAN_MODE_BAR1_SHIFT 0 +#define SPECIFIC_ENDIAN_MODE_BAR1_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) +#define SPECIFIC_ENDIAN_MODE_BAR2_SHIFT 2 +#define SPECIFIC_ENDIAN_MODE_BAR2_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) +#define SPECIFIC_ENDIAN_MODE_BAR3_SHIFT 4 +#define SPECIFIC_ENDIAN_MODE_BAR3_MASK (0x3 << SPECIFIC_ENDIAN_MODE_BAR1_SHIFT) +#define SPECIFIC_ENDIAN_MODE_WORD_ALIGN 0 +#define SPECIFIC_ENDIAN_MODE_HALFWORD_ALIGN 1 +#define SPECIFIC_ENDIAN_MODE_BYTE_ALIGN 2 + +#define PCIE_CONFIG2_REG 0x408 +#define CONFIG2_BAR1_SIZE_EN 1 +#define CONFIG2_BAR1_SIZE_MASK 0xf + +#define PCIE_IDVAL3_REG 0x43c +#define IDVAL3_CLASS_CODE_MASK 0xffffff +#define IDVAL3_SUBCLASS_SHIFT 8 +#define IDVAL3_CLASS_SHIFT 16 + +#define PCIE_DLSTATUS_REG 0x1048 +#define DLSTATUS_PHYLINKUP (1 << 13) + +#define PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG 0x400c +#define C2P_MEM_WIN_ENDIAN_MODE_MASK 0x3 +#define C2P_MEM_WIN_ENDIAN_NO_SWAP 0 +#define C2P_MEM_WIN_ENDIAN_HALF_WORD_SWAP 1 +#define C2P_MEM_WIN_ENDIAN_HALF_BYTE_SWAP 2 +#define C2P_MEM_WIN_BASE_ADDR_SHIFT 20 +#define C2P_MEM_WIN_BASE_ADDR_MASK (0xfff << C2P_MEM_WIN_BASE_ADDR_SHIFT) + +#define PCIE_RC_BAR1_CONFIG_LO_REG 0x402c +#define RC_BAR_CFG_LO_SIZE_256MB 0xd +#define RC_BAR_CFG_LO_MATCH_ADDR_SHIFT 20 +#define RC_BAR_CFG_LO_MATCH_ADDR_MASK (0xfff << RC_BAR_CFG_LO_MATCH_ADDR_SHIFT) + +#define PCIE_CPU_2_PCIE_MEM_WIN0_BASELIMIT_REG 0x4070 +#define C2P_BASELIMIT_LIMIT_SHIFT 20 +#define C2P_BASELIMIT_LIMIT_MASK (0xfff << C2P_BASELIMIT_LIMIT_SHIFT) +#define C2P_BASELIMIT_BASE_SHIFT 4 +#define C2P_BASELIMIT_BASE_MASK (0xfff << C2P_BASELIMIT_BASE_SHIFT) + +#define PCIE_UBUS_BAR1_CFG_REMAP_REG 0x4088 +#define BAR1_CFG_REMAP_OFFSET_SHIFT 20 +#define BAR1_CFG_REMAP_OFFSET_MASK (0xfff << BAR1_CFG_REMAP_OFFSET_SHIFT) +#define BAR1_CFG_REMAP_ACCESS_EN 1 + +#define PCIE_HARD_DEBUG_REG 0x4204 +#define HARD_DEBUG_SERDES_IDDQ (1 << 23) + +#define PCIE_CPU_INT1_MASK_CLEAR_REG 0x830c +#define CPU_INT_PCIE_ERR_ATTN_CPU (1 << 0) +#define CPU_INT_PCIE_INTA (1 << 1) +#define CPU_INT_PCIE_INTB (1 << 2) +#define CPU_INT_PCIE_INTC (1 << 3) +#define CPU_INT_PCIE_INTD (1 << 4) +#define CPU_INT_PCIE_INTR (1 << 5) +#define CPU_INT_PCIE_NMI (1 << 6) +#define CPU_INT_PCIE_UBUS (1 << 7) +#define CPU_INT_IPI (1 << 8) + +#define PCIE_EXT_CFG_INDEX_REG 0x8400 +#define EXT_CFG_FUNC_NUM_SHIFT 12 +#define EXT_CFG_FUNC_NUM_MASK (0x7 << EXT_CFG_FUNC_NUM_SHIFT) +#define EXT_CFG_DEV_NUM_SHIFT 15 +#define EXT_CFG_DEV_NUM_MASK (0xf << EXT_CFG_DEV_NUM_SHIFT) +#define EXT_CFG_BUS_NUM_SHIFT 20 +#define EXT_CFG_BUS_NUM_MASK (0xff << EXT_CFG_BUS_NUM_SHIFT) + +#define PCIE_DEVICE_OFFSET 0x9000 + +struct bcm6318_pcie { + void __iomem *base; + int irq; + struct clk *clk; + struct clk *clk25; + struct clk *clk_ubus; + struct reset_control *reset; + struct reset_control *reset_ext; + struct reset_control *reset_core; + struct reset_control *reset_hard; +}; + +static struct bcm6318_pcie bcm6318_pcie; + +extern int bmips_pci_irq; + +/* + * swizzle 32bits data to return only the needed part + */ +static int postprocess_read(u32 data, int where, unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (data >> ((where & 3) << 3)) & 0xff; + break; + case 2: + ret = (data >> ((where & 3) << 3)) & 0xffff; + break; + case 4: + ret = data; + break; + } + + return ret; +} + +static int preprocess_write(u32 orig_data, u32 val, int where, + unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (orig_data & ~(0xff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 2: + ret = (orig_data & ~(0xffff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 4: + ret = val; + break; + } + + return ret; +} + +static int bcm6318_pcie_can_access(struct pci_bus *bus, int devfn) +{ + struct bcm6318_pcie *priv = &bcm6318_pcie; + + switch (bus->number) { + case PCIE_BUS_BRIDGE: + return PCI_SLOT(devfn) == 0; + case PCIE_BUS_DEVICE: + if (PCI_SLOT(devfn) == 0) + return __raw_readl(priv->base + PCIE_DLSTATUS_REG) + & DLSTATUS_PHYLINKUP; + /* else, fall through */ + default: + return false; + } +} + +static int bcm6318_pcie_read(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + struct bcm6318_pcie *priv = &bcm6318_pcie; + u32 data; + u32 reg = where & ~3; + + if (!bcm6318_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + + if (bus->number == PCIE_BUS_DEVICE) + reg += PCIE_DEVICE_OFFSET; + + data = __raw_readl(priv->base + reg); + *val = postprocess_read(data, where, size); + + return PCIBIOS_SUCCESSFUL; +} + +static int bcm6318_pcie_write(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 val) +{ + struct bcm6318_pcie *priv = &bcm6318_pcie; + u32 data; + u32 reg = where & ~3; + + if (!bcm6318_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + + if (bus->number == PCIE_BUS_DEVICE) + reg += PCIE_DEVICE_OFFSET; + + data = __raw_readl(priv->base + reg); + data = preprocess_write(data, val, where, size); + __raw_writel(data, priv->base + reg); + + return PCIBIOS_SUCCESSFUL; +} + +static struct pci_ops bcm6318_pcie_ops = { + .read = bcm6318_pcie_read, + .write = bcm6318_pcie_write, +}; + +static struct resource bcm6318_pcie_io_resource; +static struct resource bcm6318_pcie_mem_resource; +static struct resource bcm6318_pcie_busn_resource; + +static struct pci_controller bcm6318_pcie_controller = { + .pci_ops = &bcm6318_pcie_ops, + .io_resource = &bcm6318_pcie_io_resource, + .mem_resource = &bcm6318_pcie_mem_resource, + .busn_resource = &bcm6318_pcie_busn_resource, +}; + +static void bcm6318_pcie_reset(struct bcm6318_pcie *priv) +{ + u32 val; + + reset_control_deassert(priv->reset_hard); + + reset_control_assert(priv->reset); + reset_control_assert(priv->reset_core); + reset_control_assert(priv->reset_ext); + mdelay(10); + + reset_control_deassert(priv->reset_ext); + mdelay(10); + + reset_control_deassert(priv->reset); + mdelay(10); + + val = __raw_readl(priv->base + PCIE_HARD_DEBUG_REG); + val &= ~HARD_DEBUG_SERDES_IDDQ; + __raw_writel(val, priv->base + PCIE_HARD_DEBUG_REG); + mdelay(10); + + reset_control_deassert(priv->reset_core); + mdelay(200); +} + +static void bcm6318_pcie_setup(struct bcm6318_pcie *priv) +{ + u32 val; + + __raw_writel(CPU_INT_PCIE_INTA | CPU_INT_PCIE_INTB | + CPU_INT_PCIE_INTC | CPU_INT_PCIE_INTD, + priv->base + PCIE_CPU_INT1_MASK_CLEAR_REG); + + val = bcm6318_pcie_mem_resource.end & C2P_BASELIMIT_LIMIT_MASK; + val |= (bcm6318_pcie_mem_resource.start >> C2P_BASELIMIT_LIMIT_SHIFT) + << C2P_BASELIMIT_BASE_SHIFT; + __raw_writel(val, priv->base + PCIE_CPU_2_PCIE_MEM_WIN0_BASELIMIT_REG); + + /* setup class code as bridge */ + val = __raw_readl(priv->base + PCIE_IDVAL3_REG); + val &= ~IDVAL3_CLASS_CODE_MASK; + val |= (PCI_CLASS_BRIDGE_PCI << IDVAL3_SUBCLASS_SHIFT); + __raw_writel(val, priv->base + PCIE_IDVAL3_REG); + + /* disable bar1 size */ + val = __raw_readl(priv->base + PCIE_CONFIG2_REG); + val &= ~CONFIG2_BAR1_SIZE_MASK; + __raw_writel(val, priv->base + PCIE_CONFIG2_REG); + + /* set bar0 to little endian */ + val = __raw_readl(priv->base + PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG); + val |= bcm6318_pcie_mem_resource.start & C2P_MEM_WIN_BASE_ADDR_MASK; + val |= C2P_MEM_WIN_ENDIAN_HALF_BYTE_SWAP; + __raw_writel(val, priv->base + PCIE_CPU_2_PCIE_MEM_WIN0_LO_REG); + + __raw_writel(SPECIFIC_ENDIAN_MODE_BYTE_ALIGN, + priv->base + PCIE_SPECIFIC_REG); + + __raw_writel(RC_BAR_CFG_LO_SIZE_256MB, + priv->base + PCIE_RC_BAR1_CONFIG_LO_REG); + + __raw_writel(BAR1_CFG_REMAP_ACCESS_EN, + priv->base + PCIE_UBUS_BAR1_CFG_REMAP_REG); + + __raw_writel(PCIE_BUS_DEVICE << EXT_CFG_BUS_NUM_SHIFT, + priv->base + PCIE_EXT_CFG_INDEX_REG); +} + +static int bcm6318_pcie_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct bcm6318_pcie *priv = &bcm6318_pcie; + struct resource *res; + int ret; + + of_pci_check_probe_only(); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->irq = platform_get_irq(pdev, 0); + if (!priv->irq) + return -ENODEV; + + bmips_pci_irq = priv->irq; + + priv->reset = devm_reset_control_get(dev, "pcie"); + if (IS_ERR(priv->reset)) + return PTR_ERR(priv->reset); + + priv->reset_ext = devm_reset_control_get(dev, "pcie-ext"); + if (IS_ERR(priv->reset_ext)) + return PTR_ERR(priv->reset_ext); + + priv->reset_core = devm_reset_control_get(dev, "pcie-core"); + if (IS_ERR(priv->reset_core)) + return PTR_ERR(priv->reset_core); + + priv->reset_hard = devm_reset_control_get(dev, "pcie-hard"); + if (IS_ERR(priv->reset_hard)) + return PTR_ERR(priv->reset_hard); + + priv->clk = devm_clk_get(dev, "pcie"); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + priv->clk25 = devm_clk_get(dev, "pcie25"); + if (IS_ERR(priv->clk25)) + return PTR_ERR(priv->clk25); + + priv->clk_ubus = devm_clk_get(dev, "pcie-ubus"); + if (IS_ERR(priv->clk_ubus)) + return PTR_ERR(priv->clk_ubus); + + ret = clk_prepare_enable(priv->clk); + if (ret) { + dev_err(dev, "could not enable clock\n"); + return ret; + } + + ret = clk_prepare_enable(priv->clk25); + if (ret) { + dev_err(dev, "could not enable clock\n"); + return ret; + } + + ret = clk_prepare_enable(priv->clk_ubus); + if (ret) { + dev_err(dev, "could not enable clock\n"); + return ret; + } + + pci_load_of_ranges(&bcm6318_pcie_controller, np); + if (!bcm6318_pcie_mem_resource.start) + return -EINVAL; + + of_pci_parse_bus_range(np, &bcm6318_pcie_busn_resource); + + bcm6318_pcie_reset(priv); + bcm6318_pcie_setup(priv); + + register_pci_controller(&bcm6318_pcie_controller); + + return 0; +} + +static const struct of_device_id bcm6318_pcie_of_match[] = { + { .compatible = "brcm,bcm6318-pcie", }, + { /* sentinel */ } +}; + +static struct platform_driver bcm6318_pcie_driver = { + .probe = bcm6318_pcie_probe, + .driver = { + .name = "bcm6318-pcie", + .of_match_table = bcm6318_pcie_of_match, + }, +}; + +int __init bcm6318_pcie_init(void) +{ + int ret = platform_driver_register(&bcm6318_pcie_driver); + if (ret) + pr_err("pci-bcm6318: Error registering platform driver!\n"); + return ret; +} +late_initcall_sync(bcm6318_pcie_init); diff --git a/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6328.c b/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6328.c new file mode 100644 index 0000000000..4c0d3723b8 --- /dev/null +++ b/target/linux/bmips/files/drivers/pci/controller/pcie-bcm6328.c @@ -0,0 +1,412 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * BCM6328 PCIe Controller Driver + * + * Copyright (C) 2020 Álvaro Fernández Rojas <noltari@gmail.com> + * Copyright (C) 2015 Jonas Gorski <jonas.gorski@gmail.com> + * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> + */ + +#include <linux/clk.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/kernel.h> +#include <linux/mfd/syscon.h> +#include <linux/mm.h> +#include <linux/of_gpio.h> +#include <linux/of_irq.h> +#include <linux/of_pci.h> +#include <linux/of_platform.h> +#include <linux/pci.h> +#include <linux/pm_domain.h> +#include <linux/pm_runtime.h> +#include <linux/reset.h> +#include <linux/regmap.h> +#include <linux/types.h> +#include <linux/vmalloc.h> + +#include "../pci.h" + +#define SERDES_PCIE_EXD_EN BIT(15) +#define SERDES_PCIE_EN BIT(0) + +#define PCIE_BUS_BRIDGE 0 +#define PCIE_BUS_DEVICE 1 + +#define PCIE_CONFIG2_REG 0x408 +#define CONFIG2_BAR1_SIZE_EN 1 +#define CONFIG2_BAR1_SIZE_MASK 0xf + +#define PCIE_IDVAL3_REG 0x43c +#define IDVAL3_CLASS_CODE_MASK 0xffffff +#define IDVAL3_SUBCLASS_SHIFT 8 +#define IDVAL3_CLASS_SHIFT 16 + +#define PCIE_DLSTATUS_REG 0x1048 +#define DLSTATUS_PHYLINKUP (1 << 13) + +#define PCIE_BRIDGE_OPT1_REG 0x2820 +#define OPT1_RD_BE_OPT_EN (1 << 7) +#define OPT1_RD_REPLY_BE_FIX_EN (1 << 9) +#define OPT1_PCIE_BRIDGE_HOLE_DET_EN (1 << 11) +#define OPT1_L1_INT_STATUS_MASK_POL (1 << 12) + +#define PCIE_BRIDGE_OPT2_REG 0x2824 +#define OPT2_UBUS_UR_DECODE_DIS (1 << 2) +#define OPT2_TX_CREDIT_CHK_EN (1 << 4) +#define OPT2_CFG_TYPE1_BD_SEL (1 << 7) +#define OPT2_CFG_TYPE1_BUS_NO_SHIFT 16 +#define OPT2_CFG_TYPE1_BUS_NO_MASK (0xff << OPT2_CFG_TYPE1_BUS_NO_SHIFT) + +#define PCIE_BRIDGE_BAR0_BASEMASK_REG 0x2828 +#define BASEMASK_REMAP_EN (1 << 0) +#define BASEMASK_SWAP_EN (1 << 1) +#define BASEMASK_MASK_SHIFT 4 +#define BASEMASK_MASK_MASK (0xfff << BASEMASK_MASK_SHIFT) +#define BASEMASK_BASE_SHIFT 20 +#define BASEMASK_BASE_MASK (0xfff << BASEMASK_BASE_SHIFT) + +#define PCIE_BRIDGE_BAR0_REBASE_ADDR_REG 0x282c +#define REBASE_ADDR_BASE_SHIFT 20 +#define REBASE_ADDR_BASE_MASK (0xfff << REBASE_ADDR_BASE_SHIFT) + +#define PCIE_BRIDGE_RC_INT_MASK_REG 0x2854 +#define PCIE_RC_INT_A (1 << 0) +#define PCIE_RC_INT_B (1 << 1) +#define PCIE_RC_INT_C (1 << 2) +#define PCIE_RC_INT_D (1 << 3) + +#define PCIE_DEVICE_OFFSET 0x8000 + +struct bcm6328_pcie { + void __iomem *base; + int irq; + struct regmap *serdes; + struct device **pm; + struct device_link **link_pm; + unsigned int num_pms; + struct clk *clk; + struct reset_control *reset; + struct reset_control *reset_ext; + struct reset_control *reset_core; + struct reset_control *reset_hard; +}; + +static struct bcm6328_pcie bcm6328_pcie; + +extern int bmips_pci_irq; + +/* + * swizzle 32bits data to return only the needed part + */ +static int postprocess_read(u32 data, int where, unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (data >> ((where & 3) << 3)) & 0xff; + break; + case 2: + ret = (data >> ((where & 3) << 3)) & 0xffff; + break; + case 4: + ret = data; + break; + } + + return ret; +} + +static int preprocess_write(u32 orig_data, u32 val, int where, + unsigned int size) +{ + u32 ret = 0; + + switch (size) { + case 1: + ret = (orig_data & ~(0xff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 2: + ret = (orig_data & ~(0xffff << ((where & 3) << 3))) | + (val << ((where & 3) << 3)); + break; + case 4: + ret = val; + break; + } + + return ret; +} + +static int bcm6328_pcie_can_access(struct pci_bus *bus, int devfn) +{ + struct bcm6328_pcie *priv = &bcm6328_pcie; + + switch (bus->number) { + case PCIE_BUS_BRIDGE: + return PCI_SLOT(devfn) == 0; + case PCIE_BUS_DEVICE: + if (PCI_SLOT(devfn) == 0) + return __raw_readl(priv->base + PCIE_DLSTATUS_REG) + & DLSTATUS_PHYLINKUP; + /* else, fall through */ + default: + return false; + } +} + +static int bcm6328_pcie_read(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 *val) +{ + struct bcm6328_pcie *priv = &bcm6328_pcie; + u32 data; + u32 reg = where & ~3; + + if (!bcm6328_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + + if (bus->number == PCIE_BUS_DEVICE) + reg += PCIE_DEVICE_OFFSET; + + data = __raw_readl(priv->base + reg); + *val = postprocess_read(data, where, size); + + return PCIBIOS_SUCCESSFUL; +} + +static int bcm6328_pcie_write(struct pci_bus *bus, unsigned int devfn, + int where, int size, u32 val) +{ + struct bcm6328_pcie *priv = &bcm6328_pcie; + u32 data; + u32 reg = where & ~3; + + if (!bcm6328_pcie_can_access(bus, devfn)) + return PCIBIOS_DEVICE_NOT_FOUND; + + if (bus->number == PCIE_BUS_DEVICE) + reg += PCIE_DEVICE_OFFSET; + + data = __raw_readl(priv->base + reg); + data = preprocess_write(data, val, where, size); + __raw_writel(data, priv->base + reg); + + return PCIBIOS_SUCCESSFUL; +} + +static struct pci_ops bcm6328_pcie_ops = { + .read = bcm6328_pcie_read, + .write = bcm6328_pcie_write, +}; + +static struct resource bcm6328_pcie_io_resource; +static struct resource bcm6328_pcie_mem_resource; +static struct resource bcm6328_pcie_busn_resource; + +static struct pci_controller bcm6328_pcie_controller = { + .pci_ops = &bcm6328_pcie_ops, + .io_resource = &bcm6328_pcie_io_resource, + .mem_resource = &bcm6328_pcie_mem_resource, + .busn_resource = &bcm6328_pcie_busn_resource, +}; + +static void bcm6328_pcie_reset(struct bcm6328_pcie *priv) +{ + regmap_write_bits(priv->serdes, 0, + SERDES_PCIE_EXD_EN | SERDES_PCIE_EN, + SERDES_PCIE_EXD_EN | SERDES_PCIE_EN); + + reset_control_assert(priv->reset); + reset_control_assert(priv->reset_core); + reset_control_assert(priv->reset_ext); + if (priv->reset_hard) { + reset_control_assert(priv->reset_hard); + mdelay(10); + reset_control_deassert(priv->reset_hard); + } + mdelay(10); + + reset_control_deassert(priv->reset_core); + reset_control_deassert(priv->reset); + mdelay(10); + + reset_control_deassert(priv->reset_ext); + mdelay(200); +} + +static void bcm6328_pcie_setup(struct bcm6328_pcie *priv) +{ + u32 val; + + val = __raw_readl(priv->base + PCIE_BRIDGE_OPT1_REG); + val |= OPT1_RD_BE_OPT_EN; + val |= OPT1_RD_REPLY_BE_FIX_EN; + val |= OPT1_PCIE_BRIDGE_HOLE_DET_EN; + val |= OPT1_L1_INT_STATUS_MASK_POL; + __raw_writel(val, priv->base + PCIE_BRIDGE_OPT1_REG); + + val = __raw_readl(priv->base + PCIE_BRIDGE_RC_INT_MASK_REG); + val |= PCIE_RC_INT_A; + val |= PCIE_RC_INT_B; + val |= PCIE_RC_INT_C; + val |= PCIE_RC_INT_D; + __raw_writel(val, priv->base + PCIE_BRIDGE_RC_INT_MASK_REG); + + val = __raw_readl(priv->base + PCIE_BRIDGE_OPT2_REG); + /* enable credit checking and error checking */ + val |= OPT2_TX_CREDIT_CHK_EN; + val |= OPT2_UBUS_UR_DECODE_DIS; + /* set device bus/func for the pcie device */ + val |= (PCIE_BUS_DEVICE << OPT2_CFG_TYPE1_BUS_NO_SHIFT); + val |= OPT2_CFG_TYPE1_BD_SEL; + __raw_writel(val, priv->base + PCIE_BRIDGE_OPT2_REG); + + /* setup class code as bridge */ + val = __raw_readl(priv->base + PCIE_IDVAL3_REG); + val &= ~IDVAL3_CLASS_CODE_MASK; + val |= (PCI_CLASS_BRIDGE_PCI << IDVAL3_SUBCLASS_SHIFT); + __raw_writel(val, priv->base + PCIE_IDVAL3_REG); + + /* disable bar1 size */ + val = __raw_readl(priv->base + PCIE_CONFIG2_REG); + val &= ~CONFIG2_BAR1_SIZE_MASK; + __raw_writel(val, priv->base + PCIE_CONFIG2_REG); + + /* set bar0 to little endian */ + val = (bcm6328_pcie_mem_resource.start >> 20) + << BASEMASK_BASE_SHIFT; + val |= (bcm6328_pcie_mem_resource.end >> 20) << BASEMASK_MASK_SHIFT; + val |= BASEMASK_REMAP_EN; + __raw_writel(val, priv->base + PCIE_BRIDGE_BAR0_BASEMASK_REG); + + val = (bcm6328_pcie_mem_resource.start >> 20) + << REBASE_ADDR_BASE_SHIFT; + __raw_writel(val, priv->base + PCIE_BRIDGE_BAR0_REBASE_ADDR_REG); +} + +static int bcm6328_pcie_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct bcm6328_pcie *priv = &bcm6328_pcie; + struct resource *res; + unsigned int i; + int ret; + + pm_runtime_enable(dev); + pm_runtime_no_callbacks(dev); + + priv->num_pms = of_count_phandle_with_args(np, "power-domains", + "#power-domain-cells"); + if (priv->num_pms > 1) { + priv->pm = devm_kcalloc(dev, priv->num_pms, + sizeof(struct device *), GFP_KERNEL); + if (!priv->pm) + return -ENOMEM; + + priv->link_pm = devm_kcalloc(dev, priv->num_pms, + sizeof(struct device_link *), + GFP_KERNEL); + if (!priv->link_pm) + return -ENOMEM; + + for (i = 0; i < priv->num_pms; i++) { + priv->pm[i] = genpd_dev_pm_attach_by_id(dev, i); + if (IS_ERR(priv->pm[i])) { + dev_err(dev, "error getting pm %d\n", i); + return -EINVAL; + } + + priv->link_pm[i] = device_link_add(dev, priv->pm[i], + DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME | + DL_FLAG_RPM_ACTIVE); + } + } + + ret = pm_runtime_get_sync(dev); + if (ret < 0) { + pm_runtime_disable(dev); + dev_info(dev, "PM prober defer: ret=%d\n", ret); + return -EPROBE_DEFER; + } + + of_pci_check_probe_only(); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->base = devm_ioremap_resource(dev, res); + if (IS_ERR(priv->base)) + return PTR_ERR(priv->base); + + priv->irq = platform_get_irq(pdev, 0); + if (!priv->irq) + return -ENODEV; + + bmips_pci_irq = priv->irq; + + priv->serdes = syscon_regmap_lookup_by_phandle(np, "brcm,serdes"); + if (IS_ERR(priv->serdes)) + return PTR_ERR(priv->serdes); + + priv->reset = devm_reset_control_get(dev, "pcie"); + if (IS_ERR(priv->reset)) + return PTR_ERR(priv->reset); + + priv->reset_ext = devm_reset_control_get(dev, "pcie-ext"); + if (IS_ERR(priv->reset_ext)) + return PTR_ERR(priv->reset_ext); + + priv->reset_core = devm_reset_control_get(dev, "pcie-core"); + if (IS_ERR(priv->reset_core)) + return PTR_ERR(priv->reset_core); + + priv->reset_hard = devm_reset_control_get_optional(dev, "pcie-hard"); + if (IS_ERR(priv->reset_hard)) + return PTR_ERR(priv->reset_hard); + + priv->clk = devm_clk_get(dev, "pcie"); + if (IS_ERR(priv->clk)) + return PTR_ERR(priv->clk); + + ret = clk_prepare_enable(priv->clk); + if (ret) { + dev_err(dev, "could not enable clock\n"); + return ret; + } + + pci_load_of_ranges(&bcm6328_pcie_controller, np); + if (!bcm6328_pcie_mem_resource.start) + return -EINVAL; + + of_pci_parse_bus_range(np, &bcm6328_pcie_busn_resource); + + bcm6328_pcie_reset(priv); + bcm6328_pcie_setup(priv); + + register_pci_controller(&bcm6328_pcie_controller); + + return 0; +} + +static const struct of_device_id bcm6328_pcie_of_match[] = { + { .compatible = "brcm,bcm6328-pcie", }, + { /* sentinel */ } +}; + +static struct platform_driver bcm6328_pcie_driver = { + .probe = bcm6328_pcie_probe, + .driver = { + .name = "bcm6328-pcie", + .of_match_table = bcm6328_pcie_of_match, + }, +}; + +int __init bcm6328_pcie_init(void) +{ + int ret = platform_driver_register(&bcm6328_pcie_driver); + if (ret) + pr_err("pci-bcm6328: Error registering platform driver!\n"); + return ret; +} +late_initcall_sync(bcm6328_pcie_init); diff --git a/target/linux/bmips/patches-5.10/600-mips-bmips-add-pci-support.patch b/target/linux/bmips/patches-5.10/600-mips-bmips-add-pci-support.patch new file mode 100644 index 0000000000..b4e7b7cfca --- /dev/null +++ b/target/linux/bmips/patches-5.10/600-mips-bmips-add-pci-support.patch @@ -0,0 +1,20 @@ +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -262,6 +262,7 @@ config BMIPS_GENERIC + select BCM7038_L1_IRQ + select BCM7120_L2_IRQ + select BRCMSTB_L2_IRQ ++ select HAVE_PCI + select IRQ_MIPS_CPU + select DMA_NONCOHERENT + select SYS_SUPPORTS_32BIT_KERNEL +--- a/arch/mips/pci/Makefile ++++ b/arch/mips/pci/Makefile +@@ -28,6 +28,7 @@ obj-$(CONFIG_PCI_XTALK_BRIDGE) += pci-xt + # These are still pretty much in the old state, watch, go blind. + # + obj-$(CONFIG_ATH79) += fixup-ath79.o ++obj-$(CONFIG_BMIPS_GENERIC) += fixup-bmips.o + obj-$(CONFIG_MIPS_COBALT) += fixup-cobalt.o + obj-$(CONFIG_LEMOTE_FULOONG2E) += fixup-fuloong2e.o ops-loongson2.o + obj-$(CONFIG_LEMOTE_MACH2F) += fixup-lemote2f.o ops-loongson2.o diff --git a/target/linux/bmips/patches-5.10/601-pci-controllers-add-bcm6328-pcie-support.patch b/target/linux/bmips/patches-5.10/601-pci-controllers-add-bcm6328-pcie-support.patch new file mode 100644 index 0000000000..d7e2fe113e --- /dev/null +++ b/target/linux/bmips/patches-5.10/601-pci-controllers-add-bcm6328-pcie-support.patch @@ -0,0 +1,22 @@ +--- a/drivers/pci/controller/Kconfig ++++ b/drivers/pci/controller/Kconfig +@@ -3,6 +3,11 @@ + menu "PCI controller drivers" + depends on PCI + ++config PCIE_BCM6328 ++ bool "BCM6328 PCIe controller" ++ depends on BMIPS_GENERIC || COMPILE_TEST ++ depends on OF ++ + config PCI_MVEBU + bool "Marvell EBU PCIe controller" + depends on ARCH_MVEBU || ARCH_DOVE || COMPILE_TEST +--- a/drivers/pci/controller/Makefile ++++ b/drivers/pci/controller/Makefile +@@ -1,4 +1,5 @@ + # SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_PCIE_BCM6328) += pcie-bcm6328.o + obj-$(CONFIG_PCIE_CADENCE) += cadence/ + obj-$(CONFIG_PCI_FTPCI100) += pci-ftpci100.o + obj-$(CONFIG_PCI_HYPERV) += pci-hyperv.o diff --git a/target/linux/bmips/patches-5.10/602-pci-controllers-add-bcm6318-pcie-support.patch b/target/linux/bmips/patches-5.10/602-pci-controllers-add-bcm6318-pcie-support.patch new file mode 100644 index 0000000000..3674028aec --- /dev/null +++ b/target/linux/bmips/patches-5.10/602-pci-controllers-add-bcm6318-pcie-support.patch @@ -0,0 +1,22 @@ +--- a/drivers/pci/controller/Kconfig ++++ b/drivers/pci/controller/Kconfig +@@ -3,6 +3,11 @@ + menu "PCI controller drivers" + depends on PCI + ++config PCIE_BCM6318 ++ bool "BCM6318 PCIe controller" ++ depends on BMIPS_GENERIC || COMPILE_TEST ++ depends on OF ++ + config PCIE_BCM6328 + bool "BCM6328 PCIe controller" + depends on BMIPS_GENERIC || COMPILE_TEST +--- a/drivers/pci/controller/Makefile ++++ b/drivers/pci/controller/Makefile +@@ -1,4 +1,5 @@ + # SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_PCIE_BCM6318) += pcie-bcm6318.o + obj-$(CONFIG_PCIE_BCM6328) += pcie-bcm6328.o + obj-$(CONFIG_PCIE_CADENCE) += cadence/ + obj-$(CONFIG_PCI_FTPCI100) += pci-ftpci100.o diff --git a/target/linux/bmips/patches-5.10/603-pci-controllers-add-bcm6348-pci-support.patch b/target/linux/bmips/patches-5.10/603-pci-controllers-add-bcm6348-pci-support.patch new file mode 100644 index 0000000000..c0572604ee --- /dev/null +++ b/target/linux/bmips/patches-5.10/603-pci-controllers-add-bcm6348-pci-support.patch @@ -0,0 +1,22 @@ +--- a/drivers/pci/controller/Kconfig ++++ b/drivers/pci/controller/Kconfig +@@ -3,6 +3,11 @@ + menu "PCI controller drivers" + depends on PCI + ++config PCI_BCM6348 ++ bool "BCM6348 PCI controller" ++ depends on BMIPS_GENERIC || COMPILE_TEST ++ depends on OF ++ + config PCIE_BCM6318 + bool "BCM6318 PCIe controller" + depends on BMIPS_GENERIC || COMPILE_TEST +--- a/drivers/pci/controller/Makefile ++++ b/drivers/pci/controller/Makefile +@@ -1,4 +1,5 @@ + # SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_PCI_BCM6348) += pci-bcm6348.o + obj-$(CONFIG_PCIE_BCM6318) += pcie-bcm6318.o + obj-$(CONFIG_PCIE_BCM6328) += pcie-bcm6328.o + obj-$(CONFIG_PCIE_CADENCE) += cadence/ |