aboutsummaryrefslogtreecommitdiffstats
path: root/target
diff options
context:
space:
mode:
Diffstat (limited to 'target')
-rwxr-xr-xtarget/linux/ipq40xx/base-files/etc/board.d/02_network3
-rw-r--r--target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata2
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh1
-rw-r--r--target/linux/ipq40xx/base-files/lib/upgrade/platform.sh3
-rw-r--r--target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts197
-rw-r--r--target/linux/ipq40xx/image/Makefile16
-rw-r--r--target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch3
7 files changed, 222 insertions, 3 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index 86787eeffd..b9e79c3b68 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -17,7 +17,8 @@ ipq40xx_setup_interfaces()
alfa-network,ap120c-ac|\
engenius,emr3500|\
engenius,ens620ext|\
- luma,wrtq-329acn)
+ luma,wrtq-329acn|\
+ plasmacloud,pa1200)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
aruba,ap-303|\
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index f33d3f331c..ade0d74341 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -101,6 +101,7 @@ case "$FIRMWARE" in
luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
+ plasmacloud,pa1200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
@@ -198,6 +199,7 @@ case "$FIRMWARE" in
luma,wrtq-329acn|\
openmesh,a42 |\
openmesh,a62 |\
+ plasmacloud,pa1200 |\
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2 |\
unielec,u4019-32m)
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
index 807a85d43c..60886071c9 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/dualboot_datachk.sh
@@ -44,6 +44,7 @@ platform_do_upgrade_dualboot_datachk() {
# boot anymore to Linux until it was reflashed with ap51-flash.
local next_boot_part="1"
case "$(board_name)" in
+ plasmacloud,pa1200|\
openmesh,a42)
primary_kernel_mtd=8
;;
diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
index 0fbce92f3b..22e9ffe114 100644
--- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh
@@ -111,7 +111,8 @@ platform_do_upgrade() {
nand_do_upgrade "$1"
;;
openmesh,a42 |\
- openmesh,a62)
+ openmesh,a62 |\
+ plasmacloud,pa1200)
PART_NAME="inactive"
platform_do_upgrade_dualboot_datachk "$1"
;;
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts
new file mode 100644
index 0000000000..bcb9552ce7
--- /dev/null
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-pa1200.dts
@@ -0,0 +1,197 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2017-2020, Sven Eckelmann <sven@narfation.org>
+ * Copyright (c) 2018, Marek Lindner <marek.lindner@kaiwoo.ai>
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Plasma Cloud PA1200";
+ compatible = "plasmacloud,pa1200";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &led_status_purple;
+ led-failsafe = &led_status_yellow;
+ led-running = &led_status_cyan;
+ led-upgrade = &led_status_yellow;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_cyan: status_cyan {
+ label = "cyan:status";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_purple: status_purple {
+ label = "purple:status";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_yellow: status_yellow {
+ label = "yellow:status";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "PlasmaCloud-PA1200";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index b3f2d1f755..b0fde22813 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -648,6 +648,22 @@ define Device/openmesh_a62
endef
TARGET_DEVICES += openmesh_a62
+define Device/plasmacloud_pa1200
+ $(call Device/FitImageLzma)
+ DEVICE_VENDOR := Plasma Cloud
+ DEVICE_MODEL := PA1200
+ SOC := qcom-ipq4018
+ DEVICE_DTS_CONFIG := config@pc.pa1200
+ BLOCKSIZE := 64k
+ KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE)
+ IMAGE_SIZE := 15616k
+ IMAGES += factory.bin
+ IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=PA1200
+ IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata
+ DEVICE_PACKAGES := uboot-envtools ipq-wifi-plasmacloud-pa1200
+endef
+TARGET_DEVICES += plasmacloud_pa1200
+
define Device/qcom_ap-dk01.1-c1
DEVICE_VENDOR := Qualcomm Atheros
DEVICE_MODEL := AP-DK01.1
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index 06dd135a59..8d725ebf9e 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,54 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,55 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8074-dragonboard.dtb \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
@@ -31,6 +31,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
+ qcom-ipq4018-meshpoint-one.dtb \
+ qcom-ipq4018-nbg6617.dtb \
+ qcom-ipq4019-oap100.dtb \
++ qcom-ipq4018-pa1200.dtb \
+ qcom-ipq4018-rt-ac58u.dtb \
+ qcom-ipq4018-wre6606.dtb \
+ qcom-ipq4018-wrtq-329acn.dtb \