aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* generic: add flow_offload accountingJohn Crispin2018-08-281-0/+70
| | | | | | | This patch makes the flow offloading layer account for the traffic inside the conntack entries. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: add a RPS balancerJohn Crispin2018-08-281-0/+93
| | | | | | | | | By default the RPS delegation will happen by masking the last few bits of skb->hash. This patch adds an inermediate hash bucket that maps the masked hash to a RPS core. This makes RPS results much more deterministic on SMP systems. Signed-off-by: John Crispin <john@phrozen.org>
* build: add mkrasimageDavid Bauer2018-08-287-208/+480
| | | | | | | | | | | | | | | The current make-ras.sh image generation script for the ZyXEL NBG6617 has portability issues with bash. Because of this, factory images are currently not built correctly by the OpenWRT buildbots. This commit replaces the make-ras.sh by C-written mkrasimage. The new mkrasimage is also compatible with other ZyXEL devices using the ras image-format. This is not tested with the NBG6616 but it correctly builds the header for ZyXEL factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix ar7100 PCI IRQ handlingDmitry Tunin2018-08-282-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently all PCI devices get the same IRQ that affects performance badly. This commit adresses this problem and cleans the code. ar7100 has a special PCI interrupt controller@18060018 that works exactly the same way as misc interrupt controller. This patch does the following: 1. Defines pci-intc interrupt controller@18060018 in dtsi. 2. Removes interrupt-controller property from PCI node. 3. Sets a correct interrupt mask for PCI devices. 4. Removes all IRQ handling code from the PCI driver. "qca,ar7100-misc-intc" should be used as the compatible property, becuase on ar7100 the controlled status register is read-only and the ack method used in "qca,ar7240-misc-intc" won't work properly. There are two very minor downsides of this patch that don't affect perormance: 1. We allocate an IRQ domain of 32 IRQ, whan we need only 5. But ar7100 aren't tiny un terms of RAM and that is not very important and can be tuned if we implement "nr-interrupts" property". 2. It reuses the same irg chip name "MISC" for both controllers. Run tested on DIR-825 B1. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
* ath79: ag71xx: apply interface mode to MII0/1_CTRL on ar71xx/ar913xChuanhong Guo2018-08-284-0/+73
| | | | | | | | | | | | | We currently don't have any code configuring interface mode in ath79, meaning that we relies on bootloader to set the correct interface mode. This patch added code to set interface correctly so that everything works even if bootloader configures it wrong.(e.g. on WNDR3800 u-boot set the second GMAC mode to RMII but it should be RGMII.) Introduced "qca,mac-idx" for the difference in MII_CTRL register value. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: replace patchesJohn Crispin2018-08-2835-1322/+1332
| | | | | | | replace our downstream version of the patches with the ones that were sent upstream. Signed-off-by: John Crispin <john@phrozen.org>
* strace: update strace to version 4.24Hauke Mehrtens2018-08-282-3/+3
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: WNR612v2: fix kernel panic due to wrong Wifi LED initMichal Cieslakiewicz2018-08-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WNR612v2 flashed with recent OpenWrt builds suffers from kernel panic at boot during wireless chip initialization, making device unusable: ath: phy0: Ignoring endianness difference in EEPROM magic bytes. ath: phy0: Enable LNA combining CPU 0 Unable to handle kernel paging request at virtual address 1000fee1, epc == 801d08f0, ra == 801d0d90 Oops[#1]: CPU: 0 PID: 469 Comm: kmodloader Not tainted 4.9.120 #0 [ ... register dump etc ... ] Kernel panic - not syncing: Fatal exception Rebooting in 1 seconds.. This simple patch fixes above error. It keeps LED table in memory after kernel init phase for ath9k driver to operate correctly (__initdata removed). Also, another bug is fixed - correct array size is provided to function that adds platform LEDs (this device has only 1 connected to Wifi chip) preventing code from going outside array bounds. Fixes: 1f5ea4eae46e ("ar71xx: add correct named default wireless led by using platform leds") Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> [trimmed commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx/generic: enable Zyxel NBG6616 in kernel config againMatthias Schiffer2018-08-271-0/+1
| | | | | | | | The NBG6616 shares a config symbol with the NBG6716. It was accidentally removed from the config when the ar71xx-tiny target was split off. Fixes: 0cd5e85e7ad6 ("ar71xx: create new ar71xx/tiny subtarget for 4MB flash devices") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ath79: initial support for Ubiquiti RouterStation and RouterStation ProMatt Merhar2018-08-277-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a shared ar7161_ubnt_routerstation.dtsi as well as two other .dts files that utilize it, ar7161_ubnt_routerstation.dts and ar7161_ubnt_routerstation-pro.dts. The modifications to generic-ubnt.mk, config-default, and base-files necessary for image generation, parsing RedBoot FIS partitions, network configuration, and sysupgrade are also included. This reintroduces vital bits from platform_do_upgrade_combined() and its supporting functions to /lib/upgrade/platform.sh, which were previously removed from ath79 in 3e9d9f62258f80298710441e0db557e59e152dcf "ath79: sysupgrade: drop unused platform checks". The new function is called "routerstation_do_upgrade" and will *only* work for the RouterStation series of boards. It does however retain the ability to downgrade (e.g. from master -> 17.01.x using sysupgrade -F). All hardware is functional including the AR8216 switch (for the Pro), wireless via ath5k/ath9k using the miniPCI slots, flash, USB, button, and LED. Switch and LAN/WAN configuration is the same as it is with the equivalent ar71xx targets. MAC addresses are assigned based upon the content stored in the RedBoot config partition. Flashing via both sysupgrade and TFTP has been confirmed to work. Also, the initramfs images are now raw .bin files instead of being wrapped in a uImage (as they currently are in ar71xx), which makes them bootable with RedBoot. One notable difference to ar71xx is the inclusion of the RedBoot "fconfig" utility (analogous to U-Boot’s fw_printenv/fw_setenv) in DEVICE_PACKAGES. The FIS partitions are probed using the RedBoot MTD parser’s DT binding, whose proper usage is mutually exclusive to defining a separate fixed-partitions node for "RedBoot config". This config partition contains the board's base MAC address. The lack of a hard-coded flash location means that the mtd-mac-address property cannot be used in the .dts, so instead fconfig is used to read the MAC addresses from flash in userspace during first boot. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-2752-145/+103
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: fix mt7620 pinmux for second SPIMathias Kresin2018-08-272-4/+4
| | | | | | | | | | | The mt7620 doesn't have a pinmux group named spi_cs1. The cs1 is part of the "spi refclk" group. The function "spi refclk" enables the second chip select. On reset, the pins of the "spi refclk" group are used as reference clock and GPIO. Signed-off-by: Mathias Kresin <dev@kresin.me>
* linux-firmware: realtek: Add FW for rtl8192eu, rtl8723au and rtl8723buHauke Mehrtens2018-08-271-0/+23
| | | | | | | These devices are more or less supported by the kmod-rtl8xxxu driver. Fixes: FS#1789 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* scripts: bundle-libraries: prevent loading host locales (FS#1803)Jo-Philipp Wich2018-08-271-5/+21
| | | | | | | | | | | | | Binary patch the bundled glibc library to inhibit loading of host locale archives in order to avoid triggering internal libc assertions when invoking shipped, bundled executables. The problem has been solved with upstream Glibc commit 0062ace229 ("Gracefully handle incompatible locale data") but we still need to deal with older Glibc binaries for some time to come. Fixes FS#1803 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* nghttp2: bump to 1.32.1Hans Dedecker2018-08-271-2/+2
| | | | | | | | | 4c76aaee Update manual pages 2b51ad67 Bump up version number to 1.32.1, LT revision to 30:3:16 708379dc Tweak nghttp2_session_set_stream_user_data 73106b0d Compile with clang-6.0 Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath10k-firmware: update both QCA988X CT variantsStijn Tintel2018-08-261-4/+4
| | | | | | This fixes slow performance with 802.11w enabled. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ath10k-ct: bump to git HEADStijn Tintel2018-08-261-3/+3
| | | | | | | | | | e0d2ce0 ath10k: Support setting tx_antenna in descriptor field. 29c644f Update to latest 4.13 and 4.16 ath10k-ct drivers. 20db9db ath10k: Support vdev stats for 4.9, 4.16 kernel fd92066 ath10k: Support 'ct-sta-mode' for 9984 firmware that supports it. 34954f0 ath10k: get_tsf, PMF Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* x86: geode: Add missing config optionsHauke Mehrtens2018-08-261-2/+2
| | | | | | | | This adds a configuration options which is needed now. Without this patch the geode build will fail. Fixes: 4eda2fddf2 ("x86/geode: enable X86_INTEL_LPSS to select PINCTRL") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iproute2: update to 4.18.0Hans Dedecker2018-08-252-40/+3
| | | | | | | | Update to the latest version of iproute2; see https://lwn.net/Articles/762515/ for a full overview of the changes in 4.18. Remove upstream patch 001-rdma-sync-some-IP-headers-with-glibc Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ath9k: fix setting up tx99 with a monitor mode interfaceFelix Fietkau2018-08-251-0/+92
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix mac address increment for embedded wireless DorinFelix Fietkau2018-08-251-0/+1
| | | | | | Use mtd-mac-address-increment-byte to match ar71xx behavior Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: make mtd mac address increment more flexibleFelix Fietkau2018-08-251-3/+9
| | | | | | Allow selecting the byte on which the increment should be added. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add missing dependency to regmap to kmod-gpio-mcp23s08Hauke Mehrtens2018-08-251-1/+1
| | | | | | | This fixes a build problem recently introduced. Fixes: a904003b9b5f ("kernel: fix kmod-gpio-mcp23s08 for linux 4.14") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: Enable USB power on WNDR3400v3Tuomas Tynkkynen2018-08-251-0/+39
| | | | | | | WNDR3400v3 needs GPIO 21 pulled high to enable power to USB ports. Add a kernel patch to do that. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
* kernel: add kmod-tcp-bbrKeith Wong2018-08-253-0/+40
| | | | | | | | | | | | This adds support for BBR (Bottleneck Bandwidth and RTT) TCP congestion control. Applications (e.g. webservers, VPN client/server) which initiate connections from router side can benefit from this. This provide an easier way for users to use BBR by selecting / installing kmod-tcp-bbr instead of altering kernel config and compiling firmware by themselves. Signed-off-by: Keith Wong <keithwky@gmail.com>
* libbsd: Update to 0.8.7Daniel Engberg2018-08-254-45/+272
| | | | | | | | | | Update libbsd to 0.8.7 Remove glibc dependency Clean up InstallDev and install entries Use /usr path for consistency Cherry pick patches from upstream to fix musl compilation Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* imx6: Initial support for SolidRun CuBox-i devices based on i.MX6 processors ↵Vladimir Vid2018-08-255-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (i1, i2, i2eX, and i4Pro). - Specifications - CuBox i1: - SoC: i.MX6 Solo - Cores: 1 - Memory Size: 512MB - GPU: GC880 - Wifi/Bluetooth: Optional - USB 2.0 ports: 2 - Ethernet: 10/100/1000 Mbps CuBox i2 | i2eX: - SoC: i.MX6 Dual Lite - Cores: 2 - Memory Size: 1GB - GPU: GC2000 - Wifi/Bluetooth: Optional - USB 2.0 ports: 2 - Ethernet: 10/100/1000 Mbps CuBox i4Pro | i4x4: - SoC: i.MX6 Quad - Cores: 4 - Memory Size: 2/4 GB - GPU: GC2000 - Wifi/Bluetooth: Build In - USB 2.0 ports: 2 - Ethernet: 10/100/1000 Mbps Built-in u-boot requires SPL (secondary program loader) to be present on the SD-card regardless of the image type which will be loaded. SPL is generated by the u-boot-mx6cuboxi package which is preselected by the target device and can be found in bin/u-boot-mx6cuboxi directory. Flashing the SPL: dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=4 dd if=bin/targets/imx6/generic/u-boot-mx6cuboxi/SPL of=/dev/mmcblk0 bs=1K seek=1 Preparing the firmware on the SD-card: (echo o; echo n; echo p; echo 1; echo ''; echo ''; echo w) | fdisk /dev/mmcblk0 mkfs.ext4 /dev/mmcblk0p1 mount /dev/mmcblk0p1 /mnt tar -xzf bin/targets/imx6/generic/openwrt-imx6-device-cubox-i-rootfs.tar.gz -C /mnt/ mkdir -p /mnt/boot cp bin/targets/imx6/generic/{*-uImage,*.dtb,*.scr} /mnt/boot/ Generated u-boot.img needs to be placed on the first partition: cp bin/targets/imx6/generic/u-boot-mx6cuboxi/u-boot.img /mnt/ To boot from the SD card: Boot script which sets mmc/dtb parameters and boots the board is automatically sourced. If this does not work for any reason: mmc dev 0; load mmc 0:1 $scriptaddr boot/boot.scr; source $scriptaddr Currently imx6dl-cubox-i.dtb (Dual Lite) and imx6q-cubox-i.dtb (Quad) device trees are available. Tested on i4Pro, MMC, USB (+ HiD), HDMI and ethernet ports are working. Wireless and bluetooth are broken ATM. According to SolidRun forums, BCM4329/BCM4330 firmware is used which works fine on older kernels. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
* mac80211: mwl8k: Expand non-DFS 5G channelsAntonio Silverio2018-08-251-0/+37
| | | | | | | Add non-DFS 5G upper channels (149-165) besides existed 4 lower channels (36, 40, 44, 48). Signed-off-by: Antonio Silverio <menion@gmail.com>
* kernel: fix kmod-gpio-mcp23s08 for linux 4.14Martin Schiller2018-08-251-3/+7
| | | | Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* x86/64: enable X86_INTEL_LPSS to select PINCTRLMartin Schiller2018-08-251-1/+10
| | | | | | | This makes it possible to use the MCP23S08 i/o expander on x86_64 platforms with linux 4.14. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* x86/geode: enable X86_INTEL_LPSS to select PINCTRLMartin Schiller2018-08-251-1/+10
| | | | | | | This makes it possible to use the MCP23S08 i/o expander on geode platforms with linux 4.14. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* zynq: add support for the Zybo Z7 boardLuis Araneda2018-08-254-0/+154
| | | | | | | | | | | | | | | | | | | The board is manufactured by Digilent Main features: - Soc: XC7Z010 (Z7-10) or XC7Z020 (Z7-20) - RAM: 1 GB DDR3L - FLASH: 16 MB QSPI - 1 Gbps Ethernet - USB 2.0 - microSD slot - Pcam camera connector - HDMI Tx and Rx - Audio codec: stereo out, stereo in, mic - 5 (Z7-10) or 6 (Z7-20) Pmod ports - 6 push-buttons, 4 switches, 5 LEDs - 1 (Z7-10) or 2 (Z7-20) RGB LEDs Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* uboot-zynq: add support for the zybo z7 boardLuis Araneda2018-08-254-6/+612
| | | | | | | | Backport board support from the upcoming v2018.09 release, and add an additional patch to read the MAC address from flash memory Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* x86: add UHCI and XHCI USB host drivers to 4.14Alex Maclean2018-08-251-1/+5
| | | | | | | | | | Without UHCI a non-trivial number of machines will have no keyboard without BIOS assistance. Add XHCI as well in case there are chipsets which don't support legacy interfaces, and support PCI OHCI controllers also. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* libevent2: Switch to using release tarballRosen Penev2018-08-252-45/+8
| | | | | | | | | | | | | Starting with version 2.1.8, a release tarball is available. Simplifies the Makefile slightly. Updated the project URL. HTTPS is broken. Issue has been reported upstream Adjusted patches. CMake support is not present in the tarball. It's made for Windows anyway. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* build: Unset CDPATH to avoid problemsThomas Langer2018-08-251-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | In some places the output of commands, which include "cd" are used. In case of CDPATH the new path is printed, which might not be expected. Disable the variable to avoid these problem. When CDPATH was set by the user to some value like "export CDPATH=." the git checkout done by the build system did not work anymore, the git cloning aborted with such an error message for example: .... Packing checkout... tar: /disk/fs1/tmp2/mehrtens/pon-ugw/ugw-haps/openwrt/tmp/dl/ppa-drv-1.0\n@1534240258: Cannot stat: No such file or directory tar: Date sample file not found Try 'tar --help' or 'tar --usage' for more information. ..... To avoid this, this patch makes the build system unset CDPATH inside the build system, so the build system will still work even when the user set this variable in his local environment. Signed-off-by: Thomas Langer <thomas.langer@intel.com> Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* mt76: update to the latest versionFelix Fietkau2018-08-241-3/+3
| | | | | | | | 7daf962 mt7603: add survey support 980c606 mt7603: add fix for CCA signal configuration 30b8371 mt7603: fix BAR rate Signed-off-by: Felix Fietkau <nbd@nbd.name>
* dropbear: backport upstream fix for CVE-2018-15599Hans Dedecker2018-08-243-3/+224
| | | | | | | | | | CVE description : The recv_msg_userauth_request function in svr-auth.c in Dropbear through 2018.76 is prone to a user enumeration vulnerability because username validity affects how fields in SSH_MSG_USERAUTH messages are handled, a similar issue to CVE-2018-15473 in an unrelated codebase. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* ramips: fix RBM11G partitioningThibaut VARÈNE2018-08-241-9/+36
| | | | | | | | | | | | | | | | | | | | | | | | | This patch improves faf64056ddd46992a75b1e277d94541c7251035c by correcting the partition scheme for the "RouterBoot" section of the flash. The partition scheme initially submitted is incorrect and does not reflect the actual flash structure. The "RouterBoot" section (name matching OEM) is subdivided in several static segments, as they are on ar71xx RB devices albeit with different offsets and sizes. The naming convention from ar71xx has been preserved, except for the bootloaders which are named "bootloader1" and "bootloader2" to avoid confusion with the master "RouterBoot" partition. The preferred 'fixed-partitions' DTS node syntax is used, with nesting support as introduced in 2a598bbaa3. "partition" is used for node names, with associated "label" to match policy set by 6dd94c2781. Leave a note in DTS to explain how the original author selected the SPI speed. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix RBM33G partitioningThibaut VARÈNE2018-08-241-9/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch improves 5684d087418d176cfdef4e045e1950ca7ba3b09f by correcting the partition scheme for the "RouterBoot" section of the flash. The partition scheme initially submitted is incorrect and does not reflect the actual flash structure. The "RouterBoot" section (name matching OEM) is subdivided in several static segments, as they are on ar71xx RB devices albeit with different offsets and sizes. The naming convention from ar71xx has been preserved, except for the bootloaders which are named "bootloader1" and "bootloader2" to avoid confusion with the master "RouterBoot" partition. The preferred 'fixed-partitions' DTS node syntax is used, with nesting support as introduced in 2a598bbaa3. "partition" is used for node names, with associated "label" to match policy set by 6dd94c2781. The OEM source code also define a "RouterBootFake" partition at the beginning of the secondary flash chip: to avoid trouble if OEM ever makes use of that space, it is also defined here. The resulting partition scheme looks like this: [ 10.114241] m25p80 spi0.0: w25x40 (512 Kbytes) [ 10.118708] 1 fixed-partitions partitions found on MTD device spi0.0 [ 10.125049] Creating 1 MTD partitions on "spi0.0": [ 10.129824] 0x000000000000-0x000000040000 : "RouterBoot" [ 10.136215] 5 fixed-partitions partitions found on MTD device RouterBoot [ 10.142894] Creating 5 MTD partitions on "RouterBoot": [ 10.148032] 0x000000000000-0x00000000f000 : "bootloader1" [ 10.154336] 0x00000000f000-0x000000010000 : "hard_config" [ 10.160665] 0x000000010000-0x00000001f000 : "bootloader2" [ 10.167046] 0x000000020000-0x000000021000 : "soft_config" [ 10.173461] 0x000000030000-0x000000031000 : "bios" [ 10.190191] m25p80 spi0.1: w25q128 (16384 Kbytes) [ 10.194950] 2 fixed-partitions partitions found on MTD device spi0.1 [ 10.201271] Creating 2 MTD partitions on "spi0.1": [ 10.206071] 0x000000000000-0x000000040000 : "RouterBootFake" [ 10.212746] 0x000000040000-0x000001000000 : "firmware" [ 10.307216] 2 minor-fw partitions found on MTD device firmware [ 10.313044] 0x000000040000-0x000000220000 : "kernel" [ 10.319002] 0x000000220000-0x000001000000 : "rootfs" [ 10.324906] mtd: device 9 (rootfs) set to be root filesystem [ 10.330678] 1 squashfs-split partitions found on MTD device rootfs [ 10.336886] 0x000000b40000-0x000001000000 : "rootfs_data" Leave a note in DTS to explain how the original author selected the SPI speed. Tested-by: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> Reviewed-by: Rafał Miłecki <rafal@milecki.pl> [rmilecki: dropped "RouterBootFake" partition] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ar71xx: fix typo in rb91x nand sourceKoen Vandeputte2018-08-241-1/+2
| | | | | | Fixes: 3b1ea0996f83 ("ar71xx: fix build error due to bad include") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: ubnt-xm: create mapping for RSSI LEDsLech Perczak2018-08-231-0/+7
| | | | | | | | | | Ubiquiti XM series boards contain a set of RSSI LEDs. Create an UCI mapping for them, so visual feedback on RSSI is available, when using userspace RSSI monitor daemon. Runtime tested using rssileds. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: hijack LED4 as booting/failsafeLech Perczak2018-08-231-1/+6
| | | | | | | | | | Create aliases for led-booting and led-failsafe pointing at ubnt:green:link4 LED, forUbiquiti XM series, so visual feedback on device status becomes available, in order to enter failsafe mode via button. led-running and led-upgrade aliases are omitted to avoid conflicting with RSSI LEDs when in normal operation. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: disable WAN on (rocket|bullet)-mLech Perczak2018-08-231-0/+2
| | | | | | | | | | | ubnt,bullet-m and ubnt,rocket-m targets support only single Ethernet port, therefore disable creation of WAN zone and interfaces for them, as their intended purpose is a wireless bridge. This aligns the configuration with one found in ar71xx target. ubnt,nano-m target is kept as is, being a two-port device. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: ubnt-xm: support ath9k firmware loadingLech Perczak2018-08-231-0/+5
| | | | | | | | Enable ath9k EEPROM extraction on boot for Ubiquiti XM-series boards. This is required for wireless interface to function. Runtime tested on Nanobridge M5. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: add support for I-O DATA ETG3-RINAGAKI Hiroshi2018-08-233-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA ETG3-R is a wired router, based on Atheros AR9342. Specification: - Atheros AR9342 - 64 MB of RAM - 8 MB of Flash - 5x 10/100/1000 Ethernet - AR8327N - 2x LEDs, 1x key - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using initramfs image: 1. Connect serial cable to UART header on ETG3-R 2. Rename OpenWrt initramfs image to "1500A8C0.img" and place it in the TFTP directory 3. Set IP address of the computer to 192.168.0.10, connect to the LAN port of ETG3-R, and start the TFTP server on the computer 4. Connect power cable to ETG3-R and turn on the router 5. Press "Enter" key when the "Hit any key to stop autoboot:" message is displayed on the console and enter the u-boot cli 6. execute following commands to change kernel address for u-boot setenv bootsf 1 setenv mtd_kernel1 "bootm 0x9f050000" saveenv 7. execute "tftpboot; bootm" command to download the initramfs image from TFTP server and boot with it 8. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for ETG3-R 9. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7620: add dir-810l network configRoger Pueyo Centelles2018-08-231-0/+1
| | | | | | | The device was not included in the /etc/board.d/02_network file, so the network wouldn't be properly set up on boot. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for ELECOM WRC-1900GSTNOGUCHI Hiroshi2018-08-236-172/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* ramips: fix compatibles in SoC dtsiMathias Kresin2018-08-233-3/+3
| | | | | | | The former used compatibles aren't defined anywhere and aren't used by the devicetree source files including them. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix GL-MT300N-V2 SoC compatibleMathias Kresin2018-08-231-1/+1
| | | | | | | | According to abbfcc85259a ("ramips: add support for GL-inet GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC compatible to match the used hardware. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-02 15:37:43 +0000