aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* uboot-lantiq: Add BT Home Hub 5A supportMathias Kresin2016-11-292-0/+352
| | | | | | | | | | | | | | | | | | Based on the submission to the uboot-lantiq repo by Martin Blumenstingl. Use the ddr_settings.h from the GPL tarball. The NAND boot optimized one (with memory tuning enabled) doesn't work for the UART boot image. Use the same mtd layout as the stock u-boot. Add add UBI support. Use the leds to indicate boot status like it is done with the stock u-boot. Switch on the red power led if kernel image can't be loaded. Otherwise switch the green led on. Make only the ramboot u-boot available. Only this image is required for the first installation of LEDE. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use BT HomeHub 5 Type A OEM partition layoutMathias Kresin2016-11-294-35/+36
| | | | | | | | | | | | | | | | | | | | This way the on nand bad block table is preserved and used. Add support for nand OOB ECC checksums as well. It should fix all reported ubi errors, which were all related to bad nand blocks and a purged on nand bad block table. The existing ubi partition will be reused, which eliminates the need to touch the caldata during initial install. The BT u-boot has support for loading a kernel from an ubi volume. It isn't necessary any longer to replace the BT u-boot with a custom compiled one to use LEDE. It is required to restore the BT Firmware and install LEDE from scratch to switch to the new partition layout. An image for restoring the BT firmware and installing LEDE is provided at https://github.com/mkresin/lede/releases. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: backport kernel patch to pass of node to nand_dt_initMathias Kresin2016-11-292-2/+27
| | | | | | | | | | | | | | | | | | | Backport upstream commit a61ae81a1907af1987ad4c77300508327bc48b23. The actually purpose of the patch was to do some cleanup. As a side effect of this cleanup, the device node is now passed to nand_dt_init. This allows to use the common nand device tree properties - nand-bus-width - nand-on-flash-bbt - nand-ecc-mode - nand-ecc-step-size - nand-ecc-strength for the plat_nand driver. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop ath9k device tree binding & ath9k pci fixupMathias Kresin2016-11-291-304/+7
| | | | | | | | | | Due to the addition of the bindings to the ath9k driver, this code isn't used any longer. The fixup is now done by the owloader. Rename the ath_eep.c file to ath5k_eep.c to indicate that this files includes ath5k related code only. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use ath9k device tree bindings binding/owl-loaderMartin Blumenstingl2016-11-2914-141/+305
| | | | | | | | | | | | | | | | | This moves the extraction of the eeprom/calibration data to a hotplug firmware script. Additionally it modifies all .dts to configure ath9k directly from within the .dts. The owl-loader approach enables support on devices with exotic eeprom data locations (such as unaligned positions on the flash or data inside an UBI volume). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> [add ath9k caldata mac address patcher] [fixes DGN3500 wifi mac] [fixes BTHOMEHUBV3A wifi mac] [set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: mac80211: disable ath9k bands via device treeMartin Blumenstingl2016-11-291-0/+32
| | | | | | | | | | | | | These properties allow overriding the settings from the EEPROM which indicate whether a band is enabled or not. Setting this property is only needed when the RF circuit does not support the 2.4GHz or 5GHz band while it is enabled nevertheless in the EEPROM. These patches will be replaced with a future upstream version which will introduces an ieee80211 device tree property to disable bands. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: mac80211: add pending ath9k EEPROM swapping patchesMartin Blumenstingl2016-11-297-0/+1730
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are two types of swapping the EEPROM data in the ath9k driver. Before this series one type of swapping could not be used without the other. The first type of swapping looks at the "magic bytes" at the start of the EEPROM data and performs swab16 on the EEPROM contents if needed. The second type of swapping is EEPROM format specific and swaps specific fields within the EEPROM itself (swab16, swab32 - depends on the EEPROM format). With this series the second part now looks at the EEPMISC register inside the EEPROM, which uses a bit to indicate if the EEPROM data is Big Endian (this is also done by the FreeBSD kernel). This has a nice advantage: currently there are some out-of-tree hacks (in OpenWrt and LEDE) where the EEPROM has a Big Endian header on a Big Endian system (= no swab16 is performed) but the EEPROM itself indicates that it's data is Little Endian. Until now the out-of-tree code simply did a swab16 before passing the data to ath9k, so ath9k first did the swab16 - this also enabled the format specific swapping. These out-of-tree hacks are still working with the new logic, but it is recommended to remove them. This implementation is based on a discussion with Arnd Bergmann who raised concerns about the robustness and portability of the swapping logic in the original OF support patch review, see [0]. After a second round of patches (= v1 of this series) neither Arnd Bergmann nor I were really happy with the complexity of the EEPROM swapping logic. Based on a discussion (see [1] and [2]) we decided that ath9k should use a defined format (specifying the endianness of the data - I went with __le16 and __le32) when accessing the EEPROM fields. A benefit of this is that we enable the EEPMISC based swapping logic by default, just like the FreeBSD driver, see [3]. On the devices which I have tested (see below) ath9k now works without having to specify the "endian_check" field in ath9k_platform_data (or a similar logic which could provide this via devicetree) as ath9k now detects the endianness automatically. Only EEPROMs which are mangled by some out-of-tree code still need the endian_check flag (or one can simply remove that mangling from the out-of-tree code). [0] http://www.spinics.net/lists/linux-wireless/msg152634.html [1] https://marc.info/?l=linux-wireless&m=147250597503174&w=2 [2] https://marc.info/?l=linux-wireless&m=147254388611344&w=2 [3] https://github.com/freebsd/freebsd/blob/50719b56d9ce8d7d4beb53b16e9edb2e9a4a7a18/sys/dev/ath/ath_hal/ah_eeprom_9287.c#L351 Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: mac80211: backport ath9k device tree support patchesMartin Blumenstingl2016-11-293-0/+194
| | | | | | | | | | | | | These patches add support for configuring ath9k based devices via devicetree. This was tested on PCI(e) based devices. This should work for AHB based devices as well (adding more AHB specific properties may still be needed) as soon as the ath79 platform is ready to populate the ath9k wmac via devicetree. This patchset was accepted upstream, more information can be found on the linux-wireless list: https://www.spinics.net/lists/linux-wireless/msg155474.html Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ar71xx: fix syntax error in /lib/ar71xx.shMatthias Schiffer2016-11-291-4/+4
| | | | | | | | Remove all comments in ubnt_xm_board_detect(), as it's not possible to add comments to specific lines of the case construct anyways. Fixes: 9a5801e7 "ar71xx: add model detection for UBNT Rocket Ti" Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: add model detection for UBNT Rocket TiMatthias Schiffer2016-11-291-1/+2
| | | | | Based-on-patch-by: Neal Oakey <neal.oakey@bingo-ev.de> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: have kmod-ipsec depend on kmod-crypto-echainivStijn Tintel2016-11-291-1/+4
| | | | | | | | | The ESP algorithms in CBC mode require echainiv, so have kmod-ipsec depend on kmod-crypto-echainiv. See upstream commit 32b6170ca59ccf07d0e394561e54b2cd9726038c. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* brcm47xx: fix initramfs image build errorFelix Fietkau2016-11-291-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* brcm47xx: merge cpu cache workaround patches into one, ensure they get ↵Felix Fietkau2016-11-292-177/+115
| | | | | | compiled out on mips74k Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove squashfs-64k rootfs image from bin directory, the generic one ↵Felix Fietkau2016-11-291-1/+0
| | | | | | is enough Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove split kernel/rootfs images where the sysupgrade image can be ↵Felix Fietkau2016-11-291-17/+1
| | | | | | written to flash directly Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove 2MB flash variant of WP543Felix Fietkau2016-11-292-7/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy devices that cannot be supported due to kernel ↵Felix Fietkau2016-11-292-38/+0
| | | | | | partition size limits Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove legacy gzip imagesFelix Fietkau2016-11-291-6/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete jffs2 image building codeFelix Fietkau2016-11-292-27/+7
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* iw: drop TX power patch that is part of upstream version nowRafał Miłecki2016-11-291-30/+0
| | | | | | | | | | | | | | | | Applying it again was resulting in duplicated TX info like: Interface wlan0 ifindex 6 wdev 0x1 addr 00:23:6a:a3:7d:00 ssid LEDE2 type AP wiphy 0 channel 11 (2462 MHz), width: 20 MHz, center1: 2462 MHz txpower 31.00 dBm txpower 31.00 dBm Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: use upstream accepted bcm47xxpart parsing fixRafał Miłecki2016-11-281-0/+3
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use upstream accepted fix for ARM core abortsRafał Miłecki2016-11-282-42/+75
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* firmware-utils: replace md5 code with Alexander Peslyak's implementationRafał Miłecki2016-11-282-337/+306
| | | | | | | | | | | | | | | | | | | Our current implementation is pretty old and uses some pre-standard/old ANSI C style that triggers warnings like: warning: call to function 'MD5_Init' without a real prototype [-Wunprototyped-calls] This is caused by declarations specified in a following way: src/md5.h:60:6: note: 'MD5_Init' was declared here void MD5_Init (); Having these warnings makes it harded to notice real problems. We could try hiding them but it makes more sense to just use a cleaner code. Another tiny gain from this switch is slightly reduced binary size, on x86_64 tplink-safeloader's size 48104 became 48003. The new code is public domain, uses "heavily cut-down BSD license". Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: add Falcon supportHauke Mehrtens2016-11-2720-1/+1494
| | | | | | | | | | | | This adds support for the Intel Falcon SoC for GPON. Support for the Falcon SoC was removed in commit c8218363951 svn rev: 40392 from OpenWrt, this commit adds it again. This patch adds a new subtarget for the Falcon SoC, but it still misses all the drivers needed to control the GPON part. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: add swconfig to the default packagesMathias Kresin2016-11-273-46/+28
| | | | | | | | | | | | The DEVICE_PACKAGES are not included in the initramfs image in case TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images with a not working network configuration because of a missing swconfig. Workaround the issues by adding the essential swconfig package to the default packages selection and deselect swconfig for boards not having swconfig included before via device packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ltq-hcd: drop packageMathias Kresin2016-11-2717-21402/+0
| | | | | | | Since ffd7c155008bff4b08197dfd710d7a1386313f98 it isn't used anymore on any supported target. Signed-off-by: Mathias Kresin <dev@kresin.me>
* gpio-button-hotplug: add more buttonsMathias Kresin2016-11-271-15/+24
| | | | | | The keycodes are used by some boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix button keys codes used in dtsMathias Kresin2016-11-2722-26/+27
| | | | | | Use keycodes that matches the intended use case based on the label. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add size checks/append metadata where missingMathias Kresin2016-11-273-30/+22
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Airlink AR670W factory imageMathias Kresin2016-11-272-8/+7
| | | | | | | Move the mkwrgimg build step to the makefile. It will be required by other boards as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: fix typo in image metadata supportMathias Kresin2016-11-271-2/+2
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: more dts cleanupMathias Kresin2016-11-278-110/+80
| | | | | | | | | | | | | | | | | | | | | | | Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this GPIO is mentioned in the GPL tarball, it doesn't do anything. The 2.4/5 GHz LEDs are connected to the wifi chips and not be controlled from the the userspace. Use the LEDs names/colours as they are used in the board manuals. Merge redundant LED configurations. Use the phy[0|1]tpt trigger for the wireless LEDs. Remove the workarounds for the not controllable wireless LEDs. Fix spi compatible strings and remove superfluous spi-max-frequency parameters. If there are two power leds, use one for indicating normal operation and one for failsafe/upgrade. Keep the on/off state of the main power led during boot. Use the usb pinmux settings from the nbg6817 gpl sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: clean up dts filesHenryk Heisig2016-11-279-284/+533
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set the pinmux to the values found in the GPL tarballs of the boards. Remove pinmux which are is not used (like nand pinmux for spi flash boards). This allows to use the wan orange led of the C2600 which had a wrong pinmux before. Might fix buttons or leds of other boards as well. Fix the LED color and the ledswitch key code of the C2600. Rename the ledgnr to ledswitch. Add support for indication the boot state using LEDs to the D7800, NBG6817, R7500 and R7500v2. Change GPIO active to readable values in D7800, EA8500, R7500, R7500v2 and R7800. Change gpioexport to gpio pinmux. Add proper "drive strenght" to i2c4_pins and use it for RPM on C2600, D7800, EA8500, R7500, R7500v2. Remove pcie pinmux from D7800. Move pinctrl to correct place in NBG6817 and R7800. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* firmware-utils: Fix build failure in mkmerakifw.c FS#298Florian Fainelli2016-11-261-9/+9
| | | | | | | | | Earlier compilers such as GCC 4 do not like anynomous unions, make it a named union "u", and update the code where relevant. Fixes FS#298 Fixes: a72e1692b8b3 ("firmware-utils: Add support for the Cisco Meraki MX60/MX60W") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* ipset: Add InstallDev to provide libipset as libraryJulian Kornberger2016-11-261-1/+8
|
* lantiq: specify the PCIe controller's interrupt, size and address cellsMartin Blumenstingl2016-11-261-2/+10
| | | | | | This allows adding devices to the PCIe controller in the .dts files. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: Register the device tree node with the PCIe controllerMartin Blumenstingl2016-11-261-1/+9
| | | | | | | This allows specifying PCI devices as children of the PCIe controller node to pass configuration data to them. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ramips: Add missing chunked-io directive to W2914NSV2.dtsiYong-hyu, Ban2016-11-261-0/+1
| | | | | | | | | Fix bug that LEDE failed to boot with this message: WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214 mt7621_spi_transfer_one_message+0x28c/0x620() Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
* ramips: SamKnows SK-WB8 DTS cleanupAndrew Yong2016-11-261-11/+6
| | | | | | Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000). Signed-off-by: Andrew Yong <me@ndoo.sg>
* kernel: fix typo in input-gpio-encoder package titleAvi H. D2016-11-261-1/+1
| | | | | | Line 115, 'rotary' was misspelled as 'rotay' Signed off by: Avinash Duduskar <strykar@hotmail.com>
* tools/cmake: update to 3.7.0Hannu Nyman2016-11-263-6/+6
| | | | | | | Release notes at https://cmake.org/cmake/help/v3.7/release/3.7.html Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/quilt: update to 0.65Hannu Nyman2016-11-262-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | User-visible changes since 0.64 are as follows: - Translation fixes - Project settings have priority - Reject binary files in patches - Fix a race condition in diff_file - Performance: Optimizations to the setup command - Performance: Optimizations to the bash completion script - Test suite: Improve the edit test case - Test suite: Make the symlink test more robust - Test suite: Test backup failure - Test suite: Test the header command with hard links - diff: Report diff failures - edit: Fix a corner case bug - mail: Fix the help text - push: Fix the synopsis - refresh: Do not remove symlinks - refresh: Break links to read-only patch files - refresh: Always preserve modification time - setup: Report failed look-ups in inspect-wrapper - quilt.el: Fix quilt-editable when patches are stored in subdirs - bash_completion: Handle spaces in file names - bash_completion: Update the list of commands - bash_completion: Add new command options - bash_completion: Fix handling of mail, new, push options - guards: Simplify the help text - guards: Include the file name also in the "Not found" case - guards: Add support for an external filelist in --check mode - guards: Report which config file has problem in --check mode - guards: Documentation update - guards: Clarify a user message Note to packagers: the Makefile was modified to take configure's --sysconfdir into account as other projects do. As a result, setting --prefix=/usr will no longer put the configuration files under /etc. You now need to explicitly pass --sysconfdir=/etc. If you don't, configuration files will go under /usr/etc, which is not what you want. This is somewhat less intuitive, but also more consistent with what other projects are doing. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* tools/scons: update to 2.5.1Hannu Nyman2016-11-261-2/+2
| | | | | | | | | RELEASE 2.5.1 - Mon, 03 Nov 2016 13:37:42 -0400 - Add scons-configure-cache.py to packaging. It was omitted - Use memoization to optimize PATH evaluation across all dependencies per node. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* Revert "mvebu: simplify etc/board.d/02_network"Felix Fietkau2016-11-251-1/+5
| | | | | | | This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d. According to reports, this introduces a regression on WRT3200ACM Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: remove kmod-ledtrig-usbdev from recently added devicesMathias Kresin2016-11-241-2/+2
| | | | | | None of the devices uses an usb led at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: move DomyWifi DW33D to nand subtargetPiotr Dymacz2016-11-243-15/+11
| | | | | | | | | This device uses NAND FLASH, so it should be kept in nand subtarget. Also, inlcude in packages kmod-usb-ledtrig-usbport instead of obsolete kmod-ledtrig-usbdev. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-248-2/+467
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* remove bogus dev/null that was accidentally introduced while applying a patchFelix Fietkau2016-11-241-0/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove another redundant KCONFIG entry in virt.mkFelix Fietkau2016-11-241-3/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix virtualization kmod dependencies and kconfig symbolsFelix Fietkau2016-11-241-18/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 21:08:01 +0000