| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
| |
Update bison to 3.5.1
Use POSIX threads as the previous option is no longer valid
Disable NLS support to be consistent with other tools such as e2fsprogs and sed
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
|
| |
Update e2fsprogs to 1.45.5
Enable pthreads support
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
| |
Remove mpbsd argument
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
|
|
| |
Update sed to 4.8
Use POSIX threads
Disable i18n and selinux support
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
| |
Update patchelf to 0.10
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
| |
Update libressl to 3.0.2 and remove 010-avoid-glibc.patch as fix is added by upstream
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds a pinmux to the shared DTSI for TP-Link TL-WR841N/ND v8,
TL-WR842N v2 and TL-MR3420 v2. It is supposed to be the equivalent
of:
/* config gpio4 as normal gpio function */
ath79_gpio_output_select(TL_MR3420V2_GPIO_USB_POWER,AR934X_GPIO_OUT_GPIO);
This allows to enable USB power on these devices.
While at it, move the jtag_disable_pins to &gpio node and remove the
redundant status=okay there.
Tested on TP-Link TL-WR842N v2.
Fixes: FS#2753
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Armin Fuerst <armin@fuerst.priv.at>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Mikrotik devices will be found in both generic and nand subtargets.
The file mikrotik-caldata.sh, currently used in generic, contains
a few lines of code that would need to be duplicated for nand
support. Instead of duplicating it, move it to target base-files,
as size impact is small and the maintenance gain should outweigh it.
This is changed separately to make life easier for the people
currently working on Mikrotik NAND support.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware
--------
SoC: Atheros AR7161
RAM: Samsung K4H511638D-UCCC
2x 64M DDR1
SPI: Micron M25P128 (16M)
WiFi: Atheros AR9160 bgn
Atheros AR9160 an
ETH: Broadcom BCM5481
LED: Power (Green/Red)
ETH (Green / Blue / Yellow)
(PHY-controlled)
WiFi 5 (Green / Blue)
WiFi 2 (Green / Blue)
BTN: Reset
Serial: Cisco-Style RJ45 - 115200 8N1
Installation
------------
1. Download the OpenWrt initramfs-image. Place it into a TFTP server
root directory and rename it to 1401A8C0.img. Configure the TFTP
server to listen at 192.168.1.66/24.
2. Connect the TFTP server to the access point.
3. Connect to the serial console of the access point. Attach power and
interrupt the boot procedure when prompted (bootdelay is 1 second).
4. Configure the U-Boot environment for booting OpenWrt from Ram and
flash:
$ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000'
$ setenv ramboot_openwrt 'setenv serverip 192.168.1.66;
tftpboot; bootm'
$ saveenv
5. Load OpenWrt into memory:
$ run ramboot_openwrt
Wait for the image to boot.
6. Transfer the OpenWrt sysupgrade image to the device. Write the image
to flash using sysupgrade:
$ sysupgrade -n /path/to/openwrt-sysuograde.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
| |
The Siemens WS-AP3610 asserts reset to the ethernet PHY with the
reset-register. Backport the necessary patches to de-assert reset
when probing the PHY.
These patches can be dropped when using kernel 5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
| |
* send: cleanup skb padding calculation
* socket: remove useless synchronize_net
Sorry for the back-to-back releases. This fixes a regression spotted by Eric
Dumazet.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Despite, since subtargets range from bcm2708 to bcm2711, it seems
appropriate to use bcm27xx instead of bcm2708 (again, as already done
for BOARDNAME).
This also renames the packages brcm2708-userland and brcm2708-gpu-fw.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
This change makes the names of Broadcom targets consistent by using
the common notation based on SoC/CPU ID (which is used internally
anyway), bcmXXXX instead of brcmXXXX.
This is even used for target TITLE in make menuconfig already,
only the short target name used brcm so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
HC5761A has only 2 LAN ports
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
| |
Update iproute2 to 5.5.0
Enable LTO to save several KB of size
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Some targets like kirkwood or omap don't use a subtarget which results
in a malformed JSON info file.
Instead of having a valid value like `"target": "ath79/tiny"` for these
targets the value is `"target": "kirkwood/"`.
This patch uses the same if condition to use `generic` if the subtarget
is empty.
Tested for the kirkwood target.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
| |
This will ensure the htc suffixed driver also gets created
chanbw debugfs entry.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This supports better per-chain noise floor reporting, which in turn allows for
better RSSI reporting in the driver.
Wave-2 fixes a long-standing rate-ctrl problem when connected to xbox (and probably other devices).
Wave-2 has fix for crash likely related to rekeying.
Wave-1 has some debugging code added where a user reported a crash.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq806x+qca9984,ipq4019+qca9986]
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Changes:
ath10k-ct: Support better RSSI measurements.
When used with recent firmware, these changes allow the driver to
query per-chain noise-floor from the radio to better calculate the
per-chain RSSI. The per-chain RSSI is then summed to provide the
'combined RSSI'. This gives better per-chain RSSI as well as combined
RSSI, especially when running with more than 20Mhz bandwidths.
Refresh patches.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq806x+qca9984,ipq4019+qca9986]
Signed-off-by: Michael Yartys <michael.yartys@protonmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This backports SATA performance boost from 5.3 kernel:
Increasing the SATA/AHCI DMA TX/RX FIFOs (P0DMACR.TXTS and .RXTS, ie.
TX_TRANSACTION_SIZE and RX_TRANSACTION_SIZE) from default 0x0 each to
0x3 each, gives a write performance boost of 120 MiB/s to 132 MiB/s from
lame 36 MiB/s to 45 MiB/s previously. Read performance is above 200
MiB/s. [tested on SSD using dd bs=4K/8K/12K/16K/20K/24K/32K: peak-perf
at 12K]
dd bs Before MB/s After MB/s Increase
4k 14.4 16.5 15%
64k 34.5 74.4 116%
1M 40.5 93.2 130%
Ref: https://forum.openwrt.org/t/sunxi-sata-write-speed-patch/54555/5
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[commit subject & description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The TL-WR940N v6 is similar to v3/v4, it just has different
LEDs and MAC address assignment.
Specification:
- 750 MHz CPU
- 32 MB of RAM
- 4 MB of FLASH
- 2.4 GHz WiFi
- 4x 10/100 Mbps Ethernet
The use of LEDs is based on ar71xx, so blue LED is used for WAN
and orange LED for diag (boot/failsafe/etc.).
Flash instruction (WebUI):
Download *-factory.bin image and upload it via the firmwary upgrade
function of the stock firmware WebUI.
Flash instruction (TFTP):
1. Set PC to fixed ip address 192.168.0.66
2. Download *-factory.bin image and rename it to
wr940nv6_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Thanks to Manuel Kock for reviewing and testing this patch.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Manuel Kock <github.web@manu.li>
|
|
|
|
|
|
|
| |
This adds the ar71xx board name to the SUPPORTED_DEVICES on ath79,
so forceless sysupgrade on this device becomes possible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since kernel 5.2 within netlink messages the NLA_F_NESTED nested flag is
validated. But swconfig/swlib doesn't set the flag for
SWITCH_ATTR_OP_VALUE_PORTS related netlink messages and assigning ports
to vlans via
swconfig dev switch0 vlan 1 set ports '0 1 2 3 4 6t'
Errors put with "Failed to set attribute: Invalid input data or
parameter".
Relax the validation rules and use the deprecated functions, to use the
same level of validation as it was till kernel 5.1. Depending on who has
swconfig related netlink messages implemented, there might be more
broken tools out there and we should keep backward compatibility if
possible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
| |
2ee323c file: poke ustream after starting deferred program
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
| |
Bump to latest commit:
c30b23e seccomp: fix resource leak
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Make run_parsers_by_type() more similar to the parse_mtd_partitions():
1. Use struct mtd_partitions
2. Use add_mtd_partitions()
This change simplifies run_parsers_by_type() by:
1. Dropping loop
2. Dropping code getting partition properties (name, offset, size)
Moreover this change allows passing more partitions details (e.g.
mask_flags).
One noticeable change introduced by this patch is adding parsed
partitions as children. This results in printing their *relative*
offsets which unifies this code with parse_mtd_partitions() behaviour.
Before:
[ 1.785448] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791642] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797537] 1 squashfs-split partitions found on MTD device rootfs
[ 1.804009] 0x0000004e0000-0x000000fb0000 : "rootfs_data"
After:
[ 1.785376] 0x00000018f800-0x000000fb0000 : "rootfs"
[ 1.791601] mtd: device 4 (rootfs) set to be root filesystem
[ 1.797491] 1 squashfs-split partitions found on MTD device rootfs
[ 1.803936] Creating 1 MTD partitions on "rootfs":
[ 1.808910] 0x000000350800-0x000000e20800 : "rootfs_data"
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Stock firmware has a vendor-defined tail at the end of uImage for image
validation. This patch enables OpenWrt installation from stock firmware
without having to access the UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This ports support for the TL-WA830RE v1 range extender from ar71xx to
ath79.
Specifications:
- SOC: Atheros AR7240
- CPU: 400MHz
- Flash: 4 MiB (Spansion S25FL032P)
- RAM: 32 MiB (Zentel A3S56D40FTP-G5)
- WLAN: Atheros AR9280 bgn 2x2
- Ethernet: 1 port (100M)
Flash instructions:
- install from u-boot with tftp (requires serial access)
> setenv ipaddr a.b.c.d
> setenv serverip e.f.g.h
> tftpboot 0x80000000 \
openwrt-ath79-tiny-tplink_tl-wa830re-v1-squashfs-factory.bin
> erase 0x9f020000 +0x3c0000
> cp.b 0x80000000 0x9f020000 0x3c0000
> bootm 0x9f020000
- flash factory image from OEM WebUI
- sysupgrade from ar71xx image
The device seems to be a clone of the following devices not yet
added to ath79:
- tl-wa701nd-v1
- tl-wa730re-v1
- tl-wa801nd-v1
- tl-wa901nd-v1
Signed-off-by: Christian Buschau <christian.buschau@mailbox.org>
[make use of ar7240_tplink.dtsi, add note about clones]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The current set of TP-Link devices with ar7240 SoC all share
the same DTSI file. As the latter is very similar to the
definition required for the to-be-supported TP-Link TL-WA devices
with ar7240, this patch splits the definitions into a shared part
for all TP-Link devices (ar7240_tplink.dtsi) and a file containing
the specific setup for the present TL-WR devices
(ar7240_tplink_tl-wr.dtsi), equivalent to the former
ar7240_tplink_tl-wr74xn-v1.dtsi.
While at it, remove unused firmware partition label and rename
pinmux_switch_led_pins.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
If bootloader doesn't terminate its last spi operation properly
before starting kernel, our first transfer in kernel becomes a
continuous transfer to that request instead of a new one.
Fix this flaw by restoring IOC register, which restored all pin
state to default.
Fixes: ebf0d8dade ("ath79: add new ar934x spi driver")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
|
|
|
|
|
| |
Fixes PKG_SOURCE_VERSION value which was wrongly set in commit f6e07c8284
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* wg-quick: android: split uids into multiple commands
Newer android's ndc implementations have limits on uid size, so we have to
break these into several lists.
* man: document dynamic debug trick for Linux
This comes up occasionally, so it may be useful to mention its
possibility in the man page. At least the Arch Linux and Ubuntu kernels
support dynamic debugging, so this advice will at least help somebody. So that
you don't have to go digging into the commit, this adds this helpful tidbit
to the man page for getting debug logs on Linux:
# modprobe wireguard && echo module wireguard +p > /sys/kernel/debug/dynamic_debug/control
* extract-{handshakes,keys}: rework for upstream kernel
These tools will now use the source code from the running kernel instead of
from the old monolithic repo. Essential for the functioning of Wireshark.
* netlink: remove libmnl requirement
We no longer require libmnl. It turns out that inlining the small subset of
libmnl that we actually use results in a smaller binary than the overhead of
linking to the external library. And we intend to gradually morph this code
into something domain specific as a libwg emerges. Performance has also
increased, thanks to the inliner. On all platforms, wg(8) only needs a normal
libc. Compile time on my system is still less than one second. So all in all
we have: smaller binary, zero dependencies, faster performance.
Packagers should no longer have their wireguard-tools package depend on
libmnl.
* embeddable-wg-library: use newer string_list
* netlink: don't pretend that sysconf isn't a function
Small cleanups.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
|
|
|
|
|
|
| |
Fixes c0c988e179a75d33c82ed0621d954fc0ac2c0c14
bcb8655 instance: add 'requirejail' attribute
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
When changing compatibles in e4ba8c82947e ("brcm63xx: use more systematic
names for image and DTS files"), I forgot to update them in kernel
patches as well. So, do it now.
Fixes: e4ba8c82947e ("brcm63xx: use more systematic names for image and DTS files")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This uses the specific SOC names for several devices where the
Chip ID was used incorrectly before.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Since the model string in DTS is not required to derive board name
anymore, we can now align it with the model name in Makefile and
the compatible.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch removes the translation of device model name into a
board name in lib/brcm63xx.sh. The latter has been actually totally
useless as we have the compatible which can be used instead of
the board name (and actually is at other targets like ath79 or ramips).
The change requires updating the base-files with the new
identifiers based on compatible.
With all "board names" replaced by the compatible, we do not need
the old scripts to detect board name anymore and can also remove
the obsolete treatment of "legacy" devices without DTS, as there
are none of those left. So, this patch removes the target-specific
board detection and uses the standard procedure in
package/base-files/files/lib/preinit/02_sysinfo
This also fixes several cases where the board name was not set or
evaluated correctly:
- asmax,ar1004g in 02_network
- telsey,magic in 09_fix_crc/02_network
- brcm,bcm96338gw in 02_network
- brcm,bcm96338w in 02_network
- brcm,bcm96348gw in 02_network
- dynalink,rta1025w in 02_network
- huawei,echolife-hg520v in 02_network
- several cases in diag.sh
The following orphaned identifiers are removed from board.d files:
- dmv-s0
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
In brcm63xx image Makefile DEVICE_PACKAGE definitions are split
into multiple lines with no apparent need.
Merge them into one line to increase readability and maintainability.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This changes brcm63xx target to achieve consistency between image
names, device nodes names, compatible, DTS name and device name
as much as possible. As with other targets, having consistent
names is supposed to make life easier for developers and reduces
the number of "variables" in the system. In particular, applying
the DTS scheme will make it easier to find the correct file and
architecture.
DTS files are named based on the increasingly common
soc-vendor-model scheme, using hyphens for separation as this seems
to be the kernel way. Since the compatible is not used at the
moment, I took the chance to also align them with this patch.
For the SOC, the already existing CFE_CHIP_ID can be exploiting
for all but two devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Most of the broadcom packaging codes were moved to broadcom.mk in commit
7f984dab1c52 ("mac80211: move broadcom packaging code to broadcom.mk"),
but b43/install still remained. Move it now.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes: ed2839ac4190 ("kernel/modules: add kmod-pmbus-zl6100 module")
Fixes: bbcb9de93547 ("Add package for gpio rotary encoder")
Fixes: 76854589829a ("package/kernel: package kmod-input-matrixkmap")
Fixes: 8bfef353850a ("kernel: rename kmod-switch-rtl8366_smi to
kmod-switch-rtl8366-smi to avoid underscores in package names")
Fixes: f03bf608b151 ("kernel: Add dummy sound driver")
Fixes: dda5d9b78643 ("ramips: rename pwm kernel module")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The $(space) definition in the hostapd Makefile ceased to work with
GNU Make 4.3 and later, leading to syntax errors in the generated
Kconfig files.
Drop the superfluous redefinition and reuse the working $(space)
declaration from rules.mk to fix this issue.
Fixes: GH#2713
Ref: https://github.com/openwrt/openwrt/pull/2713#issuecomment-583722469
Reported-by: Karel Kočí <cynerd@email.cz>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Tested-by: Shaleen Jain <shaleen@jain.sh>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
| |
The correct model name of WF-2881 is WF2881 without hyphen. The former used
boardnames are not added to SUPPORTED_DEVICES, to make it explicit that the
sysupgrade-tar image, which is newly added in the previous commit, should
not be used to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
| |
WF-2881 sysupgrade image uses UBI rootfs, but still relies on
default_do_upgrade. Because of this, config backup is not restored after
sysupgrade. It can be fixed by switching to nand_do_upgrade and
sysupgrade-tar image. default_do_upgrade does not handle sysupgrade-tar
properly, so one should use factory image to upgrade from older version.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
|
|
|
|
|
|
|
|
|
|
| |
Inspired by commit c48b571ad708, add an LED trigger for the WAN LED on top of
the TP-Link TL-WR902AC v1. Currently, only the LED on the port itself shows the
link state, while the LED on top of the device stays dark.
The WAN port of the device is a hybrid LAN/WAN one, hence why the LED at the
port was labeled LAN.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
|
|
|
|
|
|
|
|
| |
AR934x chips also got the 'old' qca,ar9330-uart in addition to the
'new' ns16550a compatible one. Add support for UART1 clock selector as
well as device-tree bindings in ar934x.dtsi to make use of that uart.
Reported-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x does not do any harm, so just set
them unconditionally.
Tested-by: Chuanhong Guo <gch981213@gmail.com
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
| |
Luxul ABR-4500 and XBR-4500 devices are wired routers with 5 Ethernet
ports and 1 USB 3.0 port. Flashing requires using Luxul firmware 6.4.0
or newer and uploading firmware using "Firmware Update" web UI page.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
|
|
|
|
|
|
| |
It's a simple tool prepending image with a Luxul header.
Signed-off-by: Dan Haab <dan.haab@legrand.com>
|