aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix AR8033 fiber operationDavid Bauer2021-06-272-7/+70
| | | | | | | | | | | | | | It was reported AR8033 did not work in fiber operation mode on the ER-X. While the earlier attempt of fixing this mitigated the issue of 1000 Base-X link mode not being supported, it also switched to the copper page, breaking fiber operation altogether. Extend the hack adding fiber operation so it does not switch to the copper page. Also remove the part where the supported link mode bit for 1000 Base-X is removed, as this is required for fiber operation. Signed-off-by: David Bauer <mail@david-bauer.net>
* generic: at803x: mask 1000 Base-X link modeDavid Bauer2021-06-272-0/+132
| | | | | | | | | | | | | | AR8031/AR8033 have different status registers for copper and fiber operation. However, the extended status register is the same for both operation modes. As a result of that, ESTATUS_1000_XFULL is set to 1 even when operating in copper TP mode. Remove this mode from the supported link modes, as this driver currently only supports copper operation. Signed-off-by: David Bauer <mail@david-bauer.net>
* dante: move to packages.gitPaul Spooren2021-06-263-207/+0
| | | | | | | Rather than maintaining it in core, move it to packages.git where it's maintained by a community. Signed-off-by: Paul Spooren <mail@aparcar.org>
* Revert "dnsmasq: Update to version 2.86test3"Kevin Darbyshire-Bryant2021-06-262-5/+5
| | | | | | | | This reverts commit 3628870015ef46eacf2c936f36e3c1ed3b4c9855. dnsmasq v2.86test3 has some issues with ubus, so is being reverted. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* Revert "dnsmasq: add config option for connmark DNS filtering"Kevin Darbyshire-Bryant2021-06-261-12/+0
| | | | | | | | | This reverts commit dea4bae7c2b963af02e1e3e3bdb5cd656a5ea3d3. dnsmasq v2.86test3 has some issues with ubus and needs reverting, hence this needs reverting. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* lantiq: xrx200: switch the subtarget to the mainline DSA driverMartin Blumenstingl2021-06-2642-8865/+945
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable the XRX200 PMAC, GSWIP DSA tag and GSIP DSA drivers in the 5.4 kernel config. Update the existing vr9_*.dts{,i} to use the new Ethernet and switch drivers. Drop the swconfig package from the xrx200 target because swconfig doesn't manage DSA based switches. The new /etc/config/network format for the DSA driver is not compatible with the old (swconfig) based one. Show a message during sysupgrade notifying users about this change and asking them to start with a fresh config (or forcefully update and then migrate the config manually). Failsafe mode can now automatically bring up the first lan interface based on board.json including DSA based setups. Drop 05_set_preinit_iface_lantiq from the xRX200 sub-target as this is not needed anymore. For now we are keeping it for the ase, xway and xway_legacy until there's some confirmation that it can be dropped from there as well. While here, some boards also receive minor fixups: - Use LAN1 as LAN1 (according to a photo this port can also be configured as WAN) on the Buffalo WBMR-300HPD. This makes it easier to read the port mapping because otherwise we would have LAN{2,3,4} and WAN (which was the case for the non-DSA version previously). - vr9_avm_fritz3390.dts: move the "gpio" comment from port 0 and 1 to their corresponding PHYs - vr9_tplink_vr200.dtsi: move the "gpio" comment from port 0 to PHY 0 - vr9_tplink_tdw89x0.dtsi: move the "gpio" comment from port 0 to PHY 0 Acked-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Tested-by: Notupus <notpp46@googlemail.com> # TD-W9980/DM200/FRITZ 7430 Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TDT VR2020 Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on TP-Link TD-W8980B Tested-by: Martin Schiller <ms@dev.tdt.de> # tested on ZyXEL P-2812HNU-F1 Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 7490 Tested-by: Daniel Kestrel <kestrel1974@t-online.de> # tested on Fritzbox 3490 Tested-by: @jospezial <jospezial@gmx.de> # tested on VGV7510KW22 (o2 Box 6431) Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* dnsmasq: add config option for connmark DNS filteringEtan Kissling2021-06-261-0/+12
| | | | | | | | This adds uci support to configure connmark based DNS filtering. Signed-off-by: Etan Kissling <etan_kissling@apple.com> (See https://lists.thekelleys.org.uk/pipermail/dnsmasq-discuss/2021q2/015151.html) Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
* dnsmasq: Update to version 2.86test3Etan Kissling2021-06-262-5/+5
| | | | | | | | | | | | | | Need this version to add config option for connmark DNS filtering. Summary of upstream CHANGELOG: * Handle DHCPREBIND requests in the DHCPv6 server code. * Fix bug which caused dnsmasq to lose track of processes forked. * Major rewrite of the DNS server and domain handling code. * Revise resource handling for number of concurrent DNS queries. * Improve efficiency of DNSSEC. * Connection track mark based DNS query filtering. Signed-off-by: Etan Kissling <etan.kissling@gmail.com>
* kernel: bump 5.4 to 5.4.128John Audia2021-06-2618-82/+28
| | | | | | | | | | | | | | | Removed upstreamed: mvebu/patches-5.4/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.127John Audia2021-06-262-4/+4
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.126John Audia2021-06-2613-25/+41
| | | | | | | | | Manually rebased: bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch All other patches automatically rebased. Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.125John Audia2021-06-262-11/+11
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.46Rui Salvaterra2021-06-263-3/+4
| | | | | | | | Add the new symbol to the generic kconfig. No deleted or manually refreshed patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: ethernet: ralink: rewrite esw_rt3050 to support link statesAlexander Couzens2021-06-253-45/+103
| | | | | | | | Ensure the esw is initialized before the ethernet device is sending packets. Further implement carrier detection similar to mt7620. If any port has a link, the ethernet device will detect a carrier. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: allow to return EPROBE_DEFER on switch_initAlexander Couzens2021-06-251-2/+7
| | | | | | | For rt3050 the switch needs to be initialized before the ethernet start sending packets. Allow switch_init to return -EPROBE_DEFER. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: move reset of the esw into the esw instead of feAlexander Couzens2021-06-254-13/+6
| | | | | | The esw reset should only done by the esw driver and not by the fe itself. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: use the reset controller api for esw & ephyAlexander Couzens2021-06-255-15/+45
| | | | | | Instead of writing direct into the reset registers. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: add fe_reset_fe() to reset fe via reset controllerAlexander Couzens2021-06-255-25/+23
| | | | | | | | The dts defines the reset fe for all architectures. However the soc code used direct register access of the reset controller. Replace the custom soc reset with a generic fe_reset_fe(). Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: ethernet: ralink: add struct fe_priv as context to fe_reset()Alexander Couzens2021-06-256-7/+7
| | | | | | | | The fe_reset function direct access the reset controller instead using the reset controller api. In preparation to use the reset controller. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* base-files: fix /tmp/TZ when zoneinfo not installedPaul Spooren2021-06-241-7/+4
| | | | | | | | | | | | The zoneinfo packages are not installed per default so neither /tmp/localtime nor /tmp/TZ is generated. This patch mostly reverts the previous fix and instead incooperates a solution suggested by Jo. Fixes "base-files: fix zoneinfo support " 8af62ed Signed-off-by: Paul Spooren <mail@aparcar.org>
* zram-swap: robustify mkswap/swapon/swapoff invocationRui Salvaterra2021-06-242-36/+13
| | | | | | | | | | | Instead of assuming /sbin contains the correct BusyBox symlinks, directly invoke the busybox executable. The required utilities are guaranteed to be present, since the zram-swap package selects them. Additionally, don't assume busybox resides in /bin, rely on PATH to find it. While at it, update the copyright year, use SPDX and switch to AUTORELEASE. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* hostapd: add support for providing vendor specific IE elementsFelix Fietkau2021-06-241-1/+4
| | | | | | They can be added as hex digit strings via the 'vendor_elements' option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: specify FritzBox 7530 LAN port label numbersRafał Miłecki2021-06-241-1/+1
| | | | | | | | | This helps managing LAN ports. Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121 Fixes: 95b0c07a618f ("ipq40xx: add support for FritzBox 7530") Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* hostapd: add default_disabled option to the supplicantRaphaël Mélotte2021-06-231-2/+8
| | | | | | | | | | | | | | | | | | | | | | | With the default configuration we generate, the supplicant starts scanning and tries to connect to any open network when the interface is enabled. In some cases it can be desirable to prevent the supplicant from scanning by itself. For example, if on the same radio an AP is configured and an unconfigured STA is added (to be configured with WPS), the AP might not be able to beacon until the STA stops scanning. In such a case, the STA configuration can still be required to set specific settings (e.g. multi_ap_backhaul_sta) so it can't be set to "disabled" in uci (because that would prevent the supplicant from being run at all). The alternative is to add the "disabled" parameter to the default network block in the supplicant configuration. This patch adds a "default_disabled" setting in UCI which, when set, adds the "disabled" parameter to the supplicant default network block. Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
* base-files: fix zoneinfo supportRosen Penev2021-06-231-7/+9
| | | | | | | | | | | | | | | | The system init script currently sets /tmp/localinfo when zoneinfo is populated. However, zoneinfo has spaces in it whereas the actual files have _ instead of spaces. This made the if condition never return true. Example failure when removing the if condition: /tmp/localtime -> /usr/share/zoneinfo/America/Los Angeles This file does not exist. America/Los_Angeles does. Ran through shfmt -w -ci -bn -sr -s Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix software reboot failure on HILINK HLK-7628NLiu Yu2021-06-231-0/+1
| | | | | | | | | | | In the new kernel version 5.X,reboot will fail. When SOC is reset, flash has not exited the 4-byte address mode, which causes the operation mode mismatch of flash during boot.Add broken-flash-reset to make flash exit 4-byte address mode before SOC reset Signed-off-by: Liu Yu <f78fk@live.com>
* ramips: add missing "pinctrl-names" for Youku YK1Shiji Yang2021-06-231-0/+1
| | | | | | | | | Without this definition ethernet led can work as usual, but it's better to re-add it. Relying on default values may cause uncontrollable factors. Fixes: 882a6116d3d6 ("ramips: improve pinctrl for Youku YK-L1") Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: mt7620: disable SOC VLANs for external switchesMichael Pratt2021-06-231-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | These boards have AR8327 or QCA8337 external ethernet switch. The SOC also has it's own internal switch where VLAN is now enabled by default. Changes to preinit caused all switches to have VLANs enabled by default even if they are not configured with a topology in uci_defaults (see commit f017f617aecbd47debd4d3a734dc0e471342db96) When both internal and external switches have VLANs, and the external switch has both LAN and WAN, the TX traffic from the SOC cannot flow to the tagged port on the external switch because the VLAN IDs are not matching. So disable the internal switch VLANs by default on these boards. Also, add a topology for the internal switch, so that on LuCI there is not an "unknown topology" warning. In theory, it may be possible to have LAN ports on both switches through internal and external PHYs, but there are no known boards that have this. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: ethernet: use more macros and bump versionMichael Pratt2021-06-234-7/+11
| | | | | | | | | | | | | | | Define and use some missing macros, and use them instead of BIT() or numbers for more readable code. Add comment for a bit change that seems unrelated to ethernet but is actually needed (PCIe Root Complex mode). Remove unknown and unused macro RST_CTRL_MCM (probably from MT7621 / MT7622) This is the last of a series of fixes, so bump version. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: fix RGMII TXID PHY modeMichael Pratt2021-06-231-1/+1
| | | | | | | | | | | | | | the register bits for TX delay and RX delay are opposites: when TX delay bit is set, delay is enabled when RX delay bit is set, delay is disabled So, when both bits are unset, it is RX delay and when both bits are set, it is TX delay Note: TXID is the default RGMII mode of the SOC Fixes: 5410a8e2959a ("ramips: mt7620: add rgmii delays support") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: add ephy-disable option to switch driverMichael Pratt2021-06-232-2/+13
| | | | | | | | | | | | | | Add back the register write to disable internal PHYs as a separate option in the code that can be set using a DTS property. Set the option to true by default when an external mt7530 switch is identified. This makes the driver more in sync with original SDK code while keeping the lines separated into different options to accommodate any board with any PHY layout. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: move mt7620_mdio_mode() to ethernet driverMichael Pratt2021-06-235-74/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The function mt7620_mdio_mode is only called once and both the function and mdio_mode block have been named incorrectly, leading to confusion and useless commits. These lines in the mdio_mode block of mt7620_hw_init are only intended for boards with an external mt7530 switch. (see commit 194ca6127ee18cd3a95da4d03f02e43b5428c0bb) Therefore, move lines from mdio_mode to the place in soc_mt7620.c where the type of mt7530 switch is identified, and move lines from mt7620_mdio_mode to a main function. mt7620_mdio_mode was called from mt7620_gsw_init where the priv struct is available, so the lines must stay in mt7620_gsw_init function. In order to keep things as simple as possible, keep the DTS property related function calls together, by moving them from mt7620_gsw_probe to init. Remove the now useless DTS properties and extra phy nodes. Fixes: 5a6229a93df8 ("ramips: remove superfluous & confusing DT binding") Fixes: b85fe43ec8c4 ("ramips: mt7620: add force use of mdio-mode") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: use DTS to set PHY base address for external PHYsMichael Pratt2021-06-2324-7/+60
| | | | | | | | | | | | | | | | | | | | | | | Set the PHY base address to 12 for mt7530 and 8 for others, which is based on the default setting for some devices from printing the register with the following command after it is written to by uboot during the boot cycle. `md 0x10117014 1` PHY_BASE option only uses 5 bits of the register, bits 16 to 20, so use 8-bit integer type. Set the option using the DTS property mediatek,ephy-base and create the gsw node if missing. Also, added a kernel message to display the EPHY base address. Note: If anything is written to a PHY address that is greater than 1 hex char (greater than 0xf) then there is adverse effects with Atheros switches. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: allow both internal and external PHYsMichael Pratt2021-06-231-62/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When the new variable ephy_base was introduced, it was not applied to the if block for mdio_mode. The first line in the mdio_mode if block sets the EPHY base address to 12 in the SOC by writing a register, but the corresponding variable in the driver was still set to the default of 0. This causes subsequent lines that write registers with the function _mt7620_mii_write to write to PHY addresses 0 through 4 while internal PHYs have been moved to addresses 12 through 16. All of these lines are intended only for PHYs on the SOC internal switch, however, they are being written to external ethernet switches if they exist at those PHY addresses 0 through 4. This causes some ethernet ports to be broken on boards with AR8327 or QCA8337 switch. Other suggested fixes move those lines to the else block of mdio_mode, but removing the else block completely also fixes it. Therefore, move the lines to the mt7620_hw_init function main block, and have only one instance of the function mtk_switch_w32 for writing the register with the EPHY base address. In theory, this also allows for boards that have both external switches and internal PHYs that lead to ethernet ports to be supported. Fixes: 391df3782914 ("ramips: mt7620: add EPHY base mdio address changing possibility") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: fix ethernet driver GMAC port initMichael Pratt2021-06-232-15/+9
| | | | | | | | | | | | | | | | | | | | | | | A workaround was added to the switch driver to set SOC port 4 as an RGMII GMAC interface based on the DTS property mediatek,port4-gmac. (previously mediatek,port4) However, the ethernet driver already does this, but is being blocked by a return statement whenever the phy-handle and fixed-link properties are both missing from nodes that define the port properties. Revert the workaround, so that both the switch driver and ethernet driver are not doing the same thing and move the phy-handle related lines down so nothing is ending the function prematurely. While at it, clean up kernel messages and delete useless return statements. Fixes: f6d81e2fa1f1 ("mt7620: gsw: make IntPHY and ExtPHY share mdio addr 4 possible") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: remove useless GMAC nodesMichael Pratt2021-06-234-27/+4
| | | | | | | | | | | | | | | | | | | These nodes are used for configuring a GMAC interface and for defining external PHYs to be accessed with MDIO. None of this is possible on MT7620N, only MT7620A, so remove them from all MT7620N DTS. When the mdio-bus node is missing, the driver returns -NODEV which causes the internal switch to not initialize. Replace that return so that everything works without the DTS node. Also, an extra kernel message to indicate for all error conditions that mdio-bus is disabled. Fixes: d482356322c9 ("ramips: mt7620n: add mdio node and disable port4 by default") Fixes: aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default") Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ramips: mt7620: simplify DTS properties for GMACMichael Pratt2021-06-2341-125/+23
| | | | | | | | | | | | | | | | | | | There are only 2 options in the driver for the function of mt7620 internal switch port 4: EPHY mode (RJ-45, internal PHY) GMAC mode (RGMII, external PHY) Let the DTS property be boolean instead of string where EPHY mode is the default. Fix how the properties are written for all DTS that use them, and add missing nodes where applicable, and remove useless nodes, and minor DTS formatting. Signed-off-by: Michael Pratt <mcpratt@pm.me>
* base-files: bring up vlan interface tooLuiz Angelo Daros de Luca2021-06-221-0/+3
| | | | | | | Vlan subinterface was never brought up when using vlan-based preinit network. Tested forcing ifname="" before preinit_ip() on a Tp-Link Archer C5v4. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* realtek: Fix failsafe modeHauke Mehrtens2021-06-222-0/+19
| | | | | | | | | | | | | | | The RTL8380-RTL9300 switches only forward packets when VLAN ID 1 is configured. Do not use the standard failsafe configuration for DSA accessing the default port directly, but configure a switch on the lan1 interface instead. This will add the VLAN ID 1 configuration to the switch: $ bridge vlan show port vlan-id lan1 1 PVID Egress Untagged switch 1 PVID Egress Untagged Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* base-files: failsafe: Remove the VLAN modifier from interface nameHauke Mehrtens2021-06-221-0/+2
| | | | | | | Some interfaces have a VLAN modifier like :t in lan1:t, this modifier should be removed from the interface before calling preinit_ip_config(). Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* base-files: failsafe: Fix IP configurationHauke Mehrtens2021-06-221-3/+9
| | | | | | | | | | | | | Adapt the preinit_config_board() to the board.json network changes. It now looks for the device and the ports variables to configure the LAN network. This works with swconfig configurations. Fixes: FS#3866 Fixes: d42640e389a8 ("base-files: use "ports" array in board.json network for bridges") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: Backport patch to automatically bring up DSA master when opening ↵Hauke Mehrtens2021-06-2221-40/+210
| | | | | | | | | | | | user port Without this patch we have to manually bring up the CPU interface in failsafe mode. This was backported from kernel 5.12. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Rafał Miłecki <rafal@milecki.pl>
* kernel-5.4: backport latest patches for wireguardJason A. Donenfeld2021-06-2212-0/+1514
| | | | | | | | | | These are the latest patches that just landed upstream for 5.13, will be backported by Greg into 5.10 (because of stable@), and are now in the 5.4 backport branch of wireguard: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Stijn Segers <foss@volatilesystems.org>
* kernel: bump 5.10 to 5.10.44Rui Salvaterra2021-06-223-3/+4
| | | | | | | | Add the new symbol to the generic kconfig. No deleted or manually refreshed patches. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: crypto: limit crypto-hw-hifn-795x to devices with pci supportAleksander Jan Bajkowski2021-06-221-1/+1
| | | | | | | CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on devices with pci support. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* realtek: Fix buffer length calculation on RTL8380 with CRC offloadBirger Koblitz2021-06-221-9/+7
| | | | | | | | | | | | | Fixes the buffer and packet length calculations for Ethernet TX on the RTL8380 SoC when CRC calculation offload is enabled. CRC-offload is always done by the SoC, but additional CRC calculation was previously done also by the kernel. It also fixes detection of the DSA tag for packets on RTL8390 SoCs for ports > 28. v2 has correct whitespace Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
* hostapd: make wnm_sleep_mode_no_keys configurableTimo Sigurdsson2021-06-221-3/+7
| | | | | | | | | | | | In the aftermath of the KRACK attacks, hostapd gained an AP-side workaround against WNM-Sleep Mode GTK/IGTK reinstallation attacks. WNM Sleep Mode is not enabled by default on OpenWrt, but it is configurable through the option wnm_sleep_mode. Thus, make the AP-side workaround configurable as well by exposing the option wnm_sleep_mode_no_keys. If you use the option wpa_disable_eapol_key_retries and have wnm_sleep_mode enabled, you might consider using this workaround. Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
* base-files: fix enabled for services with only STOPKarel Kočí2021-06-221-1/+6
| | | | | | | | | | | | | | | There are services that have only STOP value set. They are executed only on shutdown and it is common to use them for system cleanup. There is one such service shipped directly with base-files, it is 'umount'. Those work the same way as those with START but enabled does not report them as enabled although it should have as they can be enabled and disabled as any other service. This also changes check from check for executable to check for symbolic link. The implementation depends on those being links to service file and it is much cleaner and direct to check for them being links. Signed-off-by: Karel Kočí <karel.koci@nic.cz>
* bcm63xx-cfe: update to the latest masterRafał Miłecki2021-06-221-4/+4
| | | | | | e5050f3 linksys: ea9500-v2: add cferam file Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: fix Ethernet broken state after interface restartRafał Miłecki2021-06-221-0/+43
| | | | | | This fixes traffic stalls after ifdown & ifup. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>