aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* mac80211: fix selecting of ath10k -ct firmwareHauke Mehrtens2018-09-272-2/+2
| | | | | | | There is not firmware file with -ct-ct postfix, remove one -ct. Fixes: 61b5b4971e7d ("mac80211: make ath10k-ct the default ath10k") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Use backports-4.19-rc5-1.tar.xzHauke Mehrtens2018-09-277-14/+349
| | | | | | | | | | This is an official release with some minor changes compared to the unofficial 4.19-rc4-1 we used before. * added bcma and ssb again, which is removed in OpenWrt * fix to build with kernel 4.19 * other minor fixes not relevant for Openwrt. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iptables: fix dependency for libip6tc on IPV6Rosy Song2018-09-261-2/+2
| | | | Signed-off-by: Rosy Song <rosysong@rosinson.com>
* uboot-lantiq: fix compatibility with gcc7Martin Schiller2018-09-261-0/+142
| | | | | | | Backport u-boot commit 704f3acfcf55343043bbed01c5fb0a0094a68e8a to fix compatibility with gcc7. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ath79: add support for Buffalo BHR-4GRVINAGAKI Hiroshi2018-09-263-5/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo BHR-4GRV is a wired router, based on Atheros AR7242. Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 5x 10/100/1000 Mbps Ethernet - 3x LEDs, 2x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the BHR-4GRV normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware upgrade 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix support for Buffalo WZR-HP-G450H and split to dts/dtsiINAGAKI Hiroshi2018-09-264-81/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are many parts that are incorrect or missing in the current code for Buffalo WZR-HP-G450H in ath79, so its support is broken. I fixed that issues and split to dts/dtsi files to add support for Buffalo BHR-4GRV. And WZR-450HP has the same hardware as WZR-HP-G450H, so I change the device name to "WZR-HP-G450H/WZR-450HP". Specification: - Atheros AR7242 - 64 MB of RAM - 32 MB of Flash - 2x 16 MB SPI-NOR flash - 3T3R 2.4 GHz wifi - SoC internal - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 5x keys - 1x USB 2.0 Type-A - UART header on PCB - JP1: Vcc, GND, TX, RX from reset button side Flash instruction using factory image: 1. Boot the WZR-HP-G450H (or WZR-450HP) normaly and connect the computer to its LAN port 2. Access to "http://192.168.11.1/cgi-bin/cgi?req=frm&frm=py-db/firmup.html" with user "bufpy" and password "otdpopy" 3. Select the OpenWrt factory image and click "OK" button to perform firmware update 4. Wait ~200 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: fix wrong pll-data value for I-O DATA WN-AC-DGR devicesINAGAKI Hiroshi2018-09-261-1/+1
| | | | | | | | The pll-data value "0x56000000" is wrong for I-O DATA WN-AC1600DGR2 and WN-AC1167DGR, so there was a problem of slowing down the speed of ethernet. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: fix Archer C20 sysupgradeSteffen Förster2018-09-261-1/+0
| | | | | | | | | | The sysupgrade image failed the check due to the wrong string in the supported devices. This patch provides the correct name by dropping the SUPPORTED_DEVICES to use the default generated name. Signed-off-by: Steffen Förster <steffen@chemnitz.freifunk.net> [drop the SUPPORTED_DEVICES, the old name was never used in a release] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix power LED DTB for wt3020Emil Muratov2018-09-261-1/+1
| | | | | | | Since c134210 power LED is no longer lights after boot-up. Reversing gpio polarity makes it work as it should be. Signed-off-by: Emil Muratov <gpm@hotplug.ru>
* ramips: ex2700: actually remove kmod-mt76*Joseph C. Lehner2018-09-261-1/+1
| | | | | | | | | | | | | | When building using the multiple devices option with per-device root filesystem, only the meta package mt76 is omitted but not the dependencies selected by the package. Explicitly exclude all 3 mt76 packages, plus the metapackage. Otherwise, these modules will be included in the build, wasting a few hundred kilobytes. Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> [mention the root cause of the issue in the commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath10k-ct: update to version ath10k-4.16Hauke Mehrtens2018-09-264-9/+219
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* iw: update nl80211.hHauke Mehrtens2018-09-261-17/+607
| | | | | | Now this file matches the version in backports. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: fix compile warning in 986-rt2x00-add-TX-LOFT-calibration.patchHauke Mehrtens2018-09-261-1/+1
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: Add patches which were added laterHauke Mehrtens2018-09-2618-677/+1
| | | | | | | | These patches were added after the new matches structure for the mac80211 package was created. All the deleted patches are already integrated in kernel 4.19-rc4. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: update to version based on 4.19-rc4Hauke Mehrtens2018-09-26105-1092/+403
| | | | | | | | | | | | This updates mac80211 to backports based on kernel 4.19-rc4. I plan to integrate all the patches which are in this tar into upstream backports soon. I used the backports generated from this code: https://github.com/hauke/backports/commits/wip2 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-2618-80/+80
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* mac80211: rt2x00: add experimental patches from Stanislaw GruszkaDaniel Golle2018-09-265-0/+1067
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: remove obsolete patchDaniel Golle2018-09-261-136/+0
| | | | | | | | According to Stanislaw Gruszka the patch 600-23-rt2x00-rt2800mmio-add-a-workaround-for-spurious-TX_F.patch should be dropped. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mac80211: rt2x00: add TX LOFT calibrationTomislav Požega2018-09-261-0/+1005
| | | | | | Add TX LOFT calibration from mtk driver. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* mac80211: rt2x00: add RXIQ calibrationTomislav Požega2018-09-261-0/+417
| | | | | | | Add RXIQ calibration found in mtk driver. With old openwrt builds this gets us ~8Mbps more of RX bandwidth (test with iPA/eLNA layout). Please try if this makes any difference among various board/RF layouts. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* mac80211: rt2x00: add RXDCOC calibrationTomislav Požega2018-09-261-0/+102
| | | | | | Add RXDCOC calibration code from mtk driver. Please try if this makes any difference among various board/RF layouts. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* mac80211: rt2x00: add r calibrationTomislav Požega2018-09-261-0/+193
| | | | | | Add r calibration code as found in mtk driver. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* mac80211: rt2x00: add RF self TXDC calibrationTomislav Požega2018-09-261-0/+89
| | | | | | Add TX self calibration based on mtk driver. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
* mac80211: rt2x00: write registers required for reducing power consumptionTomislav Požega2018-09-261-0/+43
| | | | | | | | | | | Write registers required for reducing power consumption like the vendor driver does when ADJUST_POWER_CONSUMPTION_SUPPORT is set. This helps devices to sync at better TX/RX rates and improves overall performance. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: edited commit message]
* linux-firmware: set PKG_MIRROR_HASHDaniel Golle2018-09-261-1/+1
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* linux-firmware: add ath10k supportJohn Crispin2018-09-262-4/+109
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ath10k-firmware: disable the package and use default linux-firmware packageJohn Crispin2018-09-261-7/+7
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mac80211: rebase ontop of v4.18.5John Crispin2018-09-26284-15968/+388
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-2616-492/+21
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch - 0013-MIPS-ath79-fix-system-restart.patch - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.129Koen Vandeputte2018-09-267-41/+21
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 3.18 to 3.18.123Koen Vandeputte2018-09-262-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* netifd: do not validate relevant section when ipv6 is not supportedRosy Song2018-09-252-3/+3
| | | | Signed-off-by: Rosy Song <rosysong@rosinson.com>
* base-files: add network_get_metric() to /lib/functions/network.shFlorian Eckert2018-09-252-1/+6
| | | | | Signed-off-by: Florian Eckert <fe@dev.tdt.de> Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
* kernel: netfilter: add IPVS kernel module supportMauro Mozzarelli2018-09-241-0/+92
| | | | | | | | | | | | | | | | IPVS (IP Virtual Server) implements transport-layer load balancing inside the Linux kernel, so called Layer-4 switching. IPVS running on a host acts as a load balancer at the front of a cluster of real servers, it can direct requests for TCP/UDP based services to the real servers, and makes services of the real servers to appear as a virtual service on a single IP address. This change adds the following kmod packages - kmod-nf-ipvs - kmod-nf-ipvs-ftp - kmod-nf-ipvs-sip Signed-off-by: Mauro Mozzarelli <mauro@ezplanet.org> Signed-off-by: Florian Eckert <fe@dev.tdt.de>
* ncurses: use default host installAndy Walsh2018-09-241-6/+0
| | | | | | * just use default host/install, so libs/headers get properly generated/installed Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
* gettext-full: host compile with -fpicAndy Walsh2018-09-241-0/+2
| | | | Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
* zram-swap: Shell cosmeticSamuel Casa2018-09-241-4/+4
| | | | Signed-off-by: Samuel Casa <samuel.casa@neratec.com>
* zram-swap: remove trailing whitespaces in init scriptSamuel Casa2018-09-241-2/+2
| | | | | | Signed-off-by: Samuel Casa <samuel.casa@neratec.com> [slightly reword subject] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* dante: disable sched_getscheduler() - not implemented in muslDavid Yang2018-09-241-3/+4
| | | | | | | | | | | | | | | | | musl doesn't come with an valid implementation of `sched_getscheduler()`; it simply returns -ENOSYS for it. Without this option (and compile dante with `sched_getscheduler()` enabled), you will get error: serverinit(): sched_getscheduler(2): failed to retrieve current cpuscheduling policy: Function not implemented and dante won't start at all. Ref: http://lists.alpinelinux.org/alpine-devel/3932.html Ref: http://lists.alpinelinux.org/alpine-devel/3936.html Signed-off-by: David Yang <mmyangfl@gmail.com> [slightly reword commit message] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* base-files: fix postinstall uci-defaults removalTony Ambardar2018-09-241-4/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 7f694582 introduced a bug where default_postinst() often fails to remove a uci-defaults script after application, leaving it to run again after a reboot. (Note: commit 7f694582 also introduced FS#1021, now fixed by 73c745f6) The subtle problem arises from the shell logical chain: [ -f "$i" ] && . "$i" && rm -f "$i" Most uci-defaults scripts contain a terminal 'exit 0' statement which, when sourced, results in the logic chain exiting before executing 'rm -f'. This was observed while testing upgrades of 'luci-app-sqm'. The solution is to wrap the shell sourcing in a subshell relative to the command 'rm -f': ( [ -f "$i" ] && . "$i" ) && rm -f "$i" Revert to using 'grep' to prefilter the list of entries from the control file, which yields the full path of uci-defaults scripts. This allows keeping the existence check, directory change and script sourcing inside the subshell, with the script removal correctly outside. This approach avoids adding a second subshell only around the "." (source) command. The change also preserves the fix FS#1021, since the full path is used to source the script, which is POSIX-portable irrespective of PATH variable or reference to the CWD. Run Tested on: LEDE 17.01.4 running ar71xx, while tracing installation of package luci-app-sqm with its associated /etc/uci-defaults/luci-sqm file. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* rules.mk: add ESED commandKonstantin Demin2018-09-241-0/+1
| | | | | | | ESED is SED with extended regular expressions turned on. Command line and usage are the same as for SED. Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
* kernel: pick earlycon regression fixes from the stable-queue.gitRafał Miłecki2018-09-243-33/+85
| | | | | | | This fixes regression introduced in kernel 4.14 and makes bcm53xx revert obsolete. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* build: drop buildbot toolchain rebuild check when not using gitFelix Fietkau2018-09-241-0/+2
| | | | | | | | The check cleans and rebuilds the toolchain if it changed on update. When building from a source tarball, it is reasonable to expect that there will be no updates, so no rebuild check is necessary Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lldpd: inhibit linking of libbsd on !GLIBCJo-Philipp Wich2018-09-241-0/+4
| | | | Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* busybox: fix dependency for IPV6Rosy Song2018-09-232-1/+2
| | | | Signed-off-by: Rosy Song <rosysong@rosinson.com>
* kernel: fix build of nftablesHauke Mehrtens2018-09-221-0/+67
| | | | | | | | Backport an additional patch from 4.16 for nftables. This fixes a build problem recently introduced. Fixes: f57806b56e5 ("kernel: generic: Fix nftables inet table breakage") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* layerscape: build ls-dpl package with linux dtc toolYangbo Lu2018-09-221-0/+3
| | | | | | | | | Building ls-dpl package requires the dtc tool. This patch is to support using linux dtc tool for ls-dpl package. This avoids compile issue when host system doesn't have the dtc tool. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix get_device_file() function of restoolYangbo Lu2018-09-221-0/+107
| | | | | | | | | | | | | | The restool failed to work with current gcc-7.3.0-musl. This patch is to add a restool fix-up patch to fix multiple problems encountered in the get_device_file() function: - The deprecated atoi() function is replaced by strtoul - An invalid memory access was being performed by using memory from dir->d_name even after closedir(). This is fixed by a strdup() on the device filename. - Also, error prints now print any relevant error code. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: update README for SD card boot and new devicesYangbo Lu2018-09-221-100/+96
| | | | | | | This patch is to update the README since SD card boot support and LS1012AFRWY/LS1021ATWR were introduced. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: add ls1012afrwy support and drop ls1012afrdmYangbo Lu2018-09-228-60/+64
| | | | | | | | | | | | | | | | | | | | | | | ls1012afrdm was no longer supported in NXP Layerscape SDK. Instead a new board ls1012afrwy was introduced in LSDK. This patch is to drop ls1012afrdm and add ls1012afrwy support. Since only 2MB NOR flash could be used, we just put u-boot and firmware on NOR flash, and put kernel/dtb/rootfs on SD card. The Layerscape FRWY-LS1012A board is an ultra-low-cost development platform for LS1012A Series Communication Processors built on Arm Cortex-A53. This tool refines the FRDM-LS1012A with more features for a better hands-on experience for IoT, edge computing, and various advanced embedded applications. Features include easy access to processor I/O, low-power operation, micro SD card storage, an M2 connector, a small form factor, and expansion board options via mikroBUS Click Module. The MicroBUS Module provides easy expansion via hundreds of powerful modules supporting sensors, actuators, memories, and displays. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-09-05 07:04:41 +0000