| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
| |
Currently enabling VLAN filtering blocks all traffic in the bridge
immediately. That is because DSA ignores all VLAN setup when VLAN
filtering is disabled, and when it is enabled, there is no VLAN entry
in the VLAN table, causing all traffic to be blocked.
Add patches to allow VLAN setup even if VLAN filtering is disabled.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
| |
The new mt76 version splits out the firmware, because the driver can also be
used for MT7663/MT7613
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Remove dependencies on core kernel headers in host tools used to build perf,
which break on any non-linux system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for 2 new uci sections.
config wifi-vlan
# iface is optional. if it is not defined the vlan will apply
# to all interfaces
option iface default_radio0
option name guest
option vid 100
option network guest
config wifi-station
# iface is optional. if it is not defined the station will apply
# to all interfaces
option iface default_radio0
# mac is optional. if it is not defined it will be a catch all
# for any sta using this key
option mac '00:11:22:33:44:55'
# vid is optional. if it is not defined, the sta will be part of
# the primary iface.
option vid 100
option key testtest
With this patch applied it is possible to use multiple PSKs on a single BSS.
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
| |
db275e1 interface-ip: fix build on non-linux systems
3392046 system-dummy: fix missing return
a56b457 netifd: wireless: add support for tracking wifi-station sections
4ce33ce netifd: wireless: add support for tracking wifi-vlan sections
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
| |
Rename it to wan to match Linksys Armada 385 series
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
| |
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
| |
Backport port mirroring support for mv88e6xxx
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
| |
MAC address is set in board.d script
Interface swapping is not needed anymore as switching to DSA breaks
previous configuration anyway
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
| |
Use ucidef to set up MAC address instead of preinit script
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
| |
eth0 has HW MAC address while eth2 does not.
Use eth0 instead so we don't have to set LAN MAC manually.
Disable unused eth2, until multi CPU port is supported.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
| |
Update network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will break the ethernet.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
| |
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
| |
Drop swconfig patches for Clearfog and Linksys WRT
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
| |
Last reports with kernel 5.4 have all been positive [1], so let's open
this to a wider range of testers.
[1] https://github.com/openwrt/openwrt/pull/2804
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Each image can take up to 0x3d60000, which means 128k more per image.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
| |
Each image can take up to 0x3d60000, which means 128k more per image.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
| |
This is useful when booting OpenWrt from ramdisks in order to have both
images partitions defined.
Furthermore, instead of always using img2 for the inactive image, let's use
img1 or img2 accordingly.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
| |
Previously the dts were using a value determined by empirical testing,
because of a spi driver/clock bug. The bug was fixed quite some time
ago. 33 MHz is the default clock frequency used by RouterBOOT and thus
safe.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
|
|
|
|
|
|
|
|
| |
2faa20e5e9d1 iwinfo: add device id for Mikrotik R11e-5HacD miniPCIe card
d577a9d38a3b iwinfo: add device id for Marvell 88W8997 SDIO wifi card
f6b7d16d2ffa iwinfo: add device id for Atheros AR9287 PCIe wifi card
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
| |
_dma_cache_wback_inv needs to be exported to load wl module successfully.
root@OpenWrt:/# insmod wl
[ 363.867779] wl: Unknown symbol _dma_cache_wback_inv (err -2)
failed to insert /lib/modules/5.4.40/wl.ko
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Cc: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
| |
Add kmod for the ST LSM6DSX IMU driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
[fixed missing regmap module dependencies]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
| |
Add missing kernel module and rename driver
Fixes: 2d8f4c4fbd46 ("kernel: iio: add st-accel driver modules")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Update the can-mcp251x-convert-to-half-duplex-SPI patch to fix reception
Some SPI host controllers such as the Cavium Thunder TX do not support
full-duplex SPI. Using half-duplex transfers allows the driver to work
with those host controllers.
This patch fixes the fact that mcp251x_hw_rx_frame was still relying on
a full-duplex transfer where bits were being shifted on MOSI at the same time
as MISO. After splitting the transaction into a spi_write_then_read() care
must be taken to ignore the first byte.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
|
| |
This fixes a regression in 5.4 that causes a crash when a driver requests
an ARM GPIO for an IRQ.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
| |
refresh kernel config by running make kernel_menuconfig and saving changes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
| |
The latest 2GiB NAND flash parts used by Gateworks ventana are 2K page-size.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
- add fxos8700 support to GW52xx/GW53xx/GW54xx
- add USB_OTG support to GW552x
- add LSM9DS1 IMU support to GW560x
- add LSM9DS1 IMU support to GW5904
- add CC1352 UART to GW5910
- add BCM4330 support to GW5910
- fix wlan regulator for GW5910
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
|
|
|
|
|
|
|
|
|
| |
32-bit x86 fail to compile fast-math feature when compiled with frame
pointer, which uses a register used in a couple of inline asm functions.
Previous versions of wolfssl had this by default. Keeping an extra
register available may increase performance, so it's being restored for
all architectures.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
This will be moved to packages:
https://github.com/openwrt/packages/pull/12378
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
| |
Does not seem to be needed here. This will be imported into packages.
Ref: https://github.com/openwrt/packages/pull/12256
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
| |
No package in base uses libconfig. Everything is in the packages feed.
Ref: https://github.com/openwrt/packages/pull/12255
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since commit 910df3f06cc902ca2cb0ca8e963e9354c930df1a we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.
On a defered init we don't see the following error message now:
[ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Due to filesystem write caching the old configuration data could stay
out of flash for a long time during a first boot after the sysupgrade.
Power loss during this period could damage the overlay data and even
make device inaccessable via the network.
Fix this by syncing data to a flash as soon as the previous
configuration will be unpacked after the sysupgrade. Also sync the FS
state after the sysupgrade.tgz archive removing to prevent duplicative
extraction of a previous configuration.
Tested with AMD Geode based board.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
|
|
|
|
|
|
| |
This directory can hold configuration-snippets which should also included in the backup.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit removes changes from upstream commits:
8e18c8e58da6 arm64: dts: marvell: armada-3720-espressobin: declare SATA
PHY property
bd3d25b07342 arm64: dts: marvell: armada-37xx: link USB hosts with their
PHYs
For most boards which have factory bootloader this caused that devices
connected to USB 3.0 and SATA port were not detected. For them to
function users would need to upgrade the bootloader to version with ARM
Trusted Firmware 2.1 or later. Unfortunately there is no official
bootloader image with updated ATF component, therefore drop these
properties from nodes. This change was also tested briefly with
bootloader with updated ATF and the ports functioned properly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
|
|
|
|
|
|
| |
Also update the U-Boot BSP patch for I2SE Duckbill devices.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
|
|
|
|
|
|
|
|
|
| |
Enable the disk-activity LED trigger for ipq806x, since this SoC has an
onboard SATA controller.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
| |
This changes the ide-disk LED trigger to the generic disk-activity as
ide-disk trigger was removed in upstream commit eb25cb9956cc ("leds:
convert IDE trigger to common disk trigger").
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit, commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").
Removing it as it should be added only on targets which has usage for
this trigger.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
| |
The buildroot and SDK both require `libncurses-dev` to be installed on
the system, however the ImageBuilder uses precompiled binaries.
This patch changes the prerequirements checks to skip the
`libncurses-dev` part if running as ImageBuilder.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
| |
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e04 ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Required for installation of autoconf:
make[5]: Entering directory `/openwrt/build_dir/host/autoconf-2.69'
Making all in bin
make[6]: Entering directory `/openwrt/build_dir/host/autoconf-2.69/bin'
autom4te_perllibdir='..'/lib AUTOM4TE_CFG='../lib/autom4te.cfg'
../bin/autom4te -B '..'/lib -B '..'/lib --language M4sh --cache
'' --melt ./autoconf.as -o autoconf.in
Can't locate Data/Dumper.pm in @INC (@INC contains: ../lib
/usr/local/lib64/perl5 /usr/local/share/perl5 /usr/lib64/perl5/vendor_perl
/usr/share/perl5/vendor_perl /usr/lib64/perl5 /usr/share/perl5 .) at
../lib/Autom4te/C4che.pm line 33.
BEGIN failed--compilation aborted at ../lib/Autom4te/C4che.pm line 33.
Compilation failed in require at ../bin/autom4te line 40.
BEGIN failed--compilation aborted at ../bin/autom4te line 40.
make[6]: *** [autoconf.in] Error 2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since DEVICE_TYPE cannot be set per device, just set DEVICE_TYPE
to "nas" for the entire subtarget, which only contains this single
device.
Note that while this looks like a cosmetic change in combination
with the previous patches, this particular patch actually changes
the packages for the device.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While the effective "default" based on frequent use is "router", the
DEVICE_TYPE variable actually provides a "basic" configuration without
selecting any additional packages.
This is currently set up with the identifier "bootloader", which seems
to be not used at all. However, the only targets not using "router" or
"nas" are actually archs38 and arc770, which use their own value
"developerboard" for DEVICE_TYPE which seems to have been invented when
these targets where added. The latter is not implemented in target.mk,
though, and will fall back to the "basic" set of packages then.
So, to clean this up and make it more readable, let's just define a
DEVICE_TYPE "basic" and use it for the aforementioned cases.
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
DEVICE_TYPE is a target/subtarget variable, and it does not have
any effect when set in a device definition. It can only be set
in a target's or subtarget's Makefile.
Consequently, having it set anyway is misleading, so this drops
all cases.
This effectively reverts the following commits:
7a1497fd601d ("apm821xx: MBL: set DEVICE_TYPE to NAS")
5b4765c93a1b ("gemini: Classify Raidsonic NAS IB-4220-B as a NAS")
cdc6de460bb4 ("gemini: D-Link DNS-313 is a NAS")
For the following commit, the variable was set when adding device
support:
27b2f0fc0fc5 ("kirkwood: add support for Iomega Storcenter ix2-200")
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|